commit d8fb63e46c upstream.
When the mcp251xfd_start_xmit() function fails, the driver stops
processing messages, and the interrupt routine does not return,
running indefinitely even after killing the running application.
Error messages:
[ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16
[ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3).
... and repeat forever.
The issue can be triggered when multiple devices share the same SPI
interface. And there is concurrent access to the bus.
The problem occurs because tx_ring->head increments even if
mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX
package while still expecting a response in
mcp251xfd_handle_tefif_one().
Resolve the issue by starting a workqueue to write the tx obj
synchronously if err = -EBUSY. In case of another error, decrement
tx_ring->head, remove skb from the echo stack, and drop the message.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Link: https://lore.kernel.org/all/20240517134355.770777-1-ivitro@gmail.com
[mkl: use more imperative wording in patch description]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 058722ee35 upstream.
Avoid spurious link status logs that may ultimately be wrong; for example,
if the link is set to down with the cable plugged, then the cable is
unplugged and after this the link is set to up, the last new log that is
appearing is incorrectly telling that the link is up.
In order to avoid errors, show link status logs after link_reset
processing, and in order to avoid spurious as much as possible, only show
the link loss when some link status change is detected.
cc: stable@vger.kernel.org
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d33fe1714a ]
For CONFIG_CPUMASK_OFFSTACK=y kernel, explicit allocation of cpumask
variable on stack is not recommended since it can cause potential stack
overflow.
Instead, kernel code should always use *cpumask_var API(s) to allocate
cpumask var in config-neutral way, leaving allocation strategy to
CONFIG_CPUMASK_OFFSTACK.
Use *cpumask_var API(s) to address it.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Link: https://lore.kernel.org/r/20240331053441.1276826-3-dawei.li@shingroup.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1c4b4d452 ]
The switch global port interrupt mask, REG_SW_PORT_INT_MASK__4, is
defined as 0x001C in ksz9477_reg.h. The designers used 32-bit value in
anticipation for increase of port count in future product but currently
the maximum port count is 7 and the effective value is 0x7F in register
0x001F. Each port has its own interrupt mask and is defined as 0x#01F.
It uses only 4 bits for different interrupts.
The developer who implemented the current interrupt mechanism in the
switch driver noticed there are similarities between the mechanism to
mask port interrupts in global interrupt and individual interrupts in
each port and so used the same code to handle these interrupts. He
updated the code to use the new macro REG_SW_PORT_INT_MASK__1 which is
defined as 0x1F in ksz_common.h but he forgot to update the 32-bit write
to 8-bit as now the mask registers are 0x1F and 0x#01F.
In addition all KSZ switches other than the KSZ9897/KSZ9893 and LAN937X
families use only 8-bit access and so this common code will eventually
be changed to accommodate them.
Fixes: e1add7dd61 ("net: dsa: microchip: use common irq routines for girq and pirq")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://lore.kernel.org/r/1719009262-2948-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d963c95bc9 ]
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54a4e5c163 ]
PHY_ID_KSZ9477 was supported but not added to the device table passed to
MODULE_DEVICE_TABLE.
Fixes: fc3973a1fa ("phy: micrel: add Microchip KSZ 9477 Switch PHY support")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49bbeb5719 ]
There are 2 types of outstanding tx skb's:
Type 1: Packets that are sitting in the drivers ind_buff that are
waiting to be batch sent to the NIC. During a device reset, these are
freed with a call to ibmvnic_tx_scrq_clean_buffer()
Type 2: Packets that have been sent to the NIC and are awaiting a TX
completion IRQ. These are free'd during a reset with a call to
clean_tx_pools()
During any reset which requires us to free the tx irq, ensure that the
Type 2 skb references are freed. Since the irq is released, it is
impossible for the NIC to inform of any completions.
Furthermore, later in the reset process is a call to init_tx_pools()
which marks every entry in the tx pool as free (ie not outstanding).
So if the driver is to make a call to init_tx_pools(), it must first
be sure that the tx pool is empty of skb references.
This issue was discovered by observing the following in the logs during
EEH testing:
TX free map points to untracked skb (tso_pool 0 idx=4)
TX free map points to untracked skb (tso_pool 0 idx=5)
TX free map points to untracked skb (tso_pool 1 idx=36)
Fixes: 65d6470d13 ("ibmvnic: clean pending indirect buffs during reset")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c28947de2b ]
The following two shared buffer operations make use of the Shared Buffer
Status Register (SBSR):
# devlink sb occupancy snapshot pci/0000:01:00.0
# devlink sb occupancy clearmax pci/0000:01:00.0
The register has two masks of 256 bits to denote on which ingress /
egress ports the register should operate on. Spectrum-4 has more than
256 ports, so the register was extended by cited commit with a new
'port_page' field.
However, when filling the register's payload, the driver specifies the
ports as absolute numbers and not relative to the first port of the port
page, resulting in memory corruptions [1].
Fix by specifying the ports relative to the first port of the port page.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
Read of size 1 at addr ffff8881068cb00f by task devlink/1566
[...]
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
mlxsw_devlink_sb_occ_snapshot+0x75/0xb0
devlink_nl_sb_occ_snapshot_doit+0x1f9/0x2a0
genl_family_rcv_msg_doit+0x20c/0x300
genl_rcv_msg+0x567/0x800
netlink_rcv_skb+0x170/0x450
genl_rcv+0x2d/0x40
netlink_unicast+0x547/0x830
netlink_sendmsg+0x8d4/0xdb0
__sys_sendto+0x49b/0x510
__x64_sys_sendto+0xe5/0x1c0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[...]
Allocated by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
copy_verifier_state+0xbc2/0xfb0
do_check_common+0x2c51/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x109/0x170
__kasan_slab_free+0x14/0x30
kfree+0xca/0x2b0
free_verifier_state+0xce/0x270
do_check_common+0x4828/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: f8538aec88 ("mlxsw: Add support for more than 256 ports in SBSR register")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad53f5f54f ]
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7be4cb7189 upstream.
After ecf848eb93 ("net: usb: ax88179_178a: fix link status when link is
set to down/up") to not reset from usbnet_open after the reset from
usbnet_probe at initialization stage to speed up this, some issues have
been reported.
It seems to happen that if the initialization is slower, and some time
passes between the probe operation and the open operation, the second reset
from open is necessary too to have the device working. The reason is that
if there is no activity with the phy, this is "disconnected".
In order to improve this, the solution is to detect when the phy is
"disconnected", and we can use the phy status register for this. So we will
only reset the device from reset operation in this situation, that is, only
if necessary.
The same bahavior is happening when the device is stopped (link set to
down) and later is restarted (link set to up), so if the phy keeps working
we only need to enable the mac again, but if enough time passes between the
device stop and restart, reset is necessary, and we can detect the
situation checking the phy status register too.
cc: stable@vger.kernel.org # 6.6+
Fixes: ecf848eb93 ("net: usb: ax88179_178a: fix link status when link is set to down/up")
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Reported-by: Antje Miederhöfer <a.miederhoefer@gmx.de>
Reported-by: Arne Fitzenreiter <arne_f@ipfire.org>
Tested-by: Yongqin Liu <yongqin.liu@linaro.org>
Tested-by: Antje Miederhöfer <a.miederhoefer@gmx.de>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8851346912 upstream.
Assign the configured channel value to the EXTTS event in the timestamp
interrupt handler. Without assigning the correct channel, applications
like ts2phc will refuse to accept the event, resulting in errors such
as:
...
ts2phc[656.834]: config item end1.ts2phc.pin_index is 0
ts2phc[656.834]: config item end1.ts2phc.channel is 3
ts2phc[656.834]: config item end1.ts2phc.extts_polarity is 2
ts2phc[656.834]: config item end1.ts2phc.extts_correction is 0
...
ts2phc[656.862]: extts on unexpected channel
ts2phc[658.141]: extts on unexpected channel
ts2phc[659.140]: extts on unexpected channel
Fixes: f4da56529d ("net: stmmac: Add support for external trigger timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20240618073821.619751-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e7962114c ]
The current code only restores PTP tx_avail count when we get DMA
mapping errors. Fix it so that the PTP tx_avail count will be
restored for both DMA mapping errors and skb_pad() errors.
Otherwise PTP TX timestamp will not be available after a PTP
packet hits the skb_pad() error.
Fixes: 83bb623c96 ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240618215313.29631-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74382aebc9 ]
Adding/updating VSI list rule, as well as allocating/freeing VSI list
resource are called several times with type ICE_SW_LKUP_LAST, which fails
because ice_update_vsi_list_rule() and ice_aq_alloc_free_vsi_list()
consider it invalid. Allow calling these functions with ICE_SW_LKUP_LAST.
This fixes at least one issue in switchdev mode, where the same rule with
different action cannot be added, e.g.:
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF1_PR
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF2_PR
Fixes: 0f94570d0c ("ice: allow adding advanced rules")
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240618210206.981885-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b95a4afe2d ]
otx2_sq_append_skb makes used of __vlan_hwaccel_push_inside()
to unoffload VLANs - push them from skb meta data into skb data.
However, it omitts a check for __vlan_hwaccel_push_inside()
returning NULL.
Found by inspection based on [1] and [2].
Compile tested only.
[1] Re: [PATCH net-next v1] net: stmmac: Enable TSO on VLANs
https://lore.kernel.org/all/ZmrN2W8Fye450TKs@shell.armlinux.org.uk/
[2] Re: [PATCH net-next v2] net: stmmac: Enable TSO on VLANs
https://lore.kernel.org/all/CANn89i+11L5=tKsa7V7Aeyxaj6nYGRwy35PAbCRYJ73G+b25sg@mail.gmail.com/
Fixes: fd9d7859db ("octeontx2-pf: Implement ingress/egress VLAN offload")
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 604141c036 ]
In virtio spec 0.95, VIRTIO_NET_F_GUEST_CSUM was designed to handle
partially checksummed packets, and the validation of fully checksummed
packets by the device is independent of VIRTIO_NET_F_GUEST_CSUM
negotiation. However, the specification erroneously stated:
"If VIRTIO_NET_F_GUEST_CSUM is not negotiated, the device MUST set flags
to zero and SHOULD supply a fully checksummed packet to the driver."
This statement is inaccurate because even without VIRTIO_NET_F_GUEST_CSUM
negotiation, the device can still set the VIRTIO_NET_HDR_F_DATA_VALID flag.
Essentially, the device can facilitate the validation of these packets'
checksums - a process known as RX checksum offloading - removing the need
for the driver to do so.
This scenario is currently not implemented in the driver and requires
correction. The necessary specification correction[1] has been made and
approved in the virtio TC vote.
[1] https://lists.oasis-open.org/archives/virtio-comment/202401/msg00011.html
Fixes: 4f49129be6 ("virtio-net: Set RXCSUM feature if GUEST_CSUM is available")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8c43360f6 ]
commit be27b89652 ("net: stmmac: replace priv->speed with
the portTransmitRate from the tc-cbs parameters") introduced
a problem. When deleting, it prompts "Invalid portTransmitRate
0 (idleSlope - sendSlope)" and exits. Add judgment on cbs.enable.
Only when offload is enabled, speed divider needs to be calculated.
Fixes: be27b89652 ("net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240617013922.1035854-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44d3ffd85 ]
When the system resumes from sleep, the phy_init_hw() function invokes
config_init(), which clears all interrupt masks and causes wake events to be
lost in subsequent wake sequences. Remove interrupt mask clearing from
config_init() and preserve relevant masks in config_intr().
Fixes: 7d901a1e87 ("net: phy: add Maxlinear GPY115/21x/24x driver")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ba13995be ]
GPY2xx devices need 3 seconds to fully switch out of loopback mode
before it can safely re-enter loopback mode. Implement timeout mechanism
to guarantee 3 seconds waited before re-enter loopback mode.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: c44d3ffd85 ("net: phy: mxl-gpy: Remove interrupt mask clearing from config_init")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c248cd836 ]
Prevent options not supported by the PHY from being requested to it by the MAC
Whenever a WOL option is supported by both, the PHY is given priority
since that usually leads to better power savings.
Fixes: e9e13b6adc ("lan743x: fix for potential NULL pointer dereference with bare card")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7725363936 ]
When Wake-on-LAN (WoL) is active and the system is in suspend mode, triggering
a system event can wake the system from sleep, which may block the data path.
To restore normal data path functionality after waking, disable all wake-up
events. Furthermore, clear all Write 1 to Clear (W1C) status bits by writing
1's to them.
Fixes: 4d94282afd ("lan743x: Add power management support")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d7198278e ]
The whole mechanism to remember occurred SPI interrupts is not atomic,
which could lead to unexpected behavior. So fix this by using atomic bit
operations instead.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20240614145030.7781-1-wahrenst@gmx.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc69ad7486 ]
A bug in https://bugzilla.kernel.org/show_bug.cgi?id=218906 describes
that irdma would break and report hardware initialization failed after
suspend/resume with Intel E810 NIC (tested on 6.9.0-rc5).
The problem is caused due to the collision between the irq numbers
requested in irdma and the irq numbers requested in other drivers
after suspend/resume.
The irq numbers used by irdma are derived from ice's ice_pf->msix_entries
which stores mappings between MSI-X index and Linux interrupt number.
It's supposed to be cleaned up when suspend and rebuilt in resume but
it's not, causing irdma using the old irq numbers stored in the old
ice_pf->msix_entries to request_irq() when resume. And eventually
collide with other drivers.
This patch fixes this problem. On suspend, we call ice_deinit_rdma() to
clean up the ice_pf->msix_entries (and free the MSI-X vectors used by
irdma if we've dynamically allocated them). On resume, we call
ice_init_rdma() to rebuild the ice_pf->msix_entries (and allocate the
MSI-X vectors if we would like to dynamically allocate them).
Fixes: f9f5301e7e ("ice: Register auxiliary device to provide RDMA")
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b8db6afbc ]
Simplify probe flow by moving all RDMA related code to ice_init_rdma().
Unroll irq allocation if RDMA initialization fails.
Implement ice_deinit_rdma() and use it in remove flow.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: bc69ad7486 ("ice: avoid IRQ collision to fix init failure on ACPI S3 resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecf0b2b8a3 ]
During chip recovery (e.g. chip reset), there is a possible situation that
kernel worker reset_work is holding the lock and waiting for kernel thread
stat_worker to be parked, while stat_worker is waiting for the release of
the same lock.
It causes a deadlock resulting in the dumping of hung tasks messages and
possible rebooting of the device.
This patch prevents the execution of stat_worker during the chip recovery.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <MingYen.Hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5edc6585aa ]
This switch family supports four LEDs for each of its six ports. Each
LED group is composed of one of these four LEDs from all six ports. LED
groups can be configured to display hardware information, such as link
activity, or manually controlled through a bitmap in registers
RTL8366RB_LED_0_1_CTRL_REG and RTL8366RB_LED_2_3_CTRL_REG.
After a reset, the default LED group configuration for groups 0 to 3
indicates, respectively, link activity, link at 1000M, 100M, and 10M, or
RTL8366RB_LED_CTRL_REG as 0x5432. These configurations are commonly used
for LED indications. However, the driver was replacing that
configuration to use manually controlled LEDs (RTL8366RB_LED_FORCE)
without providing a way for the OS to control them. The default
configuration is deemed more useful than fixed, uncontrollable turned-on
LEDs.
The driver was enabling/disabling LEDs during port_enable/disable.
However, these events occur when the port is administratively controlled
(up or down) and are not related to link presence. Additionally, when a
port N was disabled, the driver was turning off all LEDs for group N,
not only the corresponding LED for port N in any of those 4 groups. In
such cases, if port 0 was brought down, the LEDs for all ports in LED
group 0 would be turned off. As another side effect, the driver was
wrongly warning that port 5 didn't have an LED ("no LED for port 5").
Since showing the administrative state of ports is not an orthodox way
to use LEDs, it was not worth it to fix it and all this code was
dropped.
The code to disable LEDs was simplified only changing each LED group to
the RTL8366RB_LED_OFF state. Registers RTL8366RB_LED_0_1_CTRL_REG and
RTL8366RB_LED_2_3_CTRL_REG are only used when the corresponding LED
group is configured with RTL8366RB_LED_FORCE and they don't need to be
cleaned. The code still references an LED controlled by
RTL8366RB_INTERRUPT_CONTROL_REG, but as of now, no test device has
actually used it. Also, some magic numbers were replaced by macros.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61752ac69b ]
gcc-9 and some other older versions produce a false-positive warning
for zeroing two fields
In file included from include/linux/string.h:369,
from drivers/net/wireless/ath/ath9k/main.c:18:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at drivers/net/wireless/ath/ath9k/main.c:140:3:
include/linux/fortify-string.h:462:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
462 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Using a struct_group seems to reliably avoid the warning and
not make the code much uglier. The combined memset() should even
save a couple of cpu cycles.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-3-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9b9741854 ]
In case of token is released due to token->state == BNXT_HWRM_DEFERRED,
released token (set to NULL) is used in log messages. This issue is
expected to be prevented by HWRM_ERR_CODE_PF_UNAVAILABLE error code. But
this error code is returned by recent firmware. So some firmware may not
return it. This may lead to NULL pointer dereference.
Adjust this issue by adding token pointer check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8fa4219dba ("bnxt_en: add dynamic debug support for HWRM messages")
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240611082547.12178-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be27b89652 ]
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61a ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9f756344 ]
TSO currently fails when the skb's gso_type field has more than one bit
set.
TSO packets can be passed from userspace using PF_PACKET, TUNTAP and a
few others, using virtio_net_hdr (e.g., PACKET_VNET_HDR). This includes
virtualization, such as QEMU, a real use-case.
The gso_type and gso_size fields as passed from userspace in
virtio_net_hdr are not trusted blindly by the kernel. It adds gso_type
|= SKB_GSO_DODGY to force the packet to enter the software GSO stack
for verification.
This issue might similarly come up when the CWR bit is set in the TCP
header for congestion control, causing the SKB_GSO_TCP_ECN gso_type bit
to be set.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Joshua Washington <joshwash@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
v2 - Remove unnecessary comments, remove line break between fixes tag
and signoffs.
v3 - Add back unrelated empty line removal.
Link: https://lore.kernel.org/r/20240610225729.2985343-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 791b4089e3 ]
Move the vxlan_features_check() call to after we verified the packet is
a tunneled VXLAN packet.
Without this, tunneled UDP non-VXLAN packets (for ex. GENENVE) might
wrongly not get offloaded.
In some cases, it worked by chance as GENEVE header is the same size as
VXLAN, but it is obviously incorrect.
Fixes: e3cfc7e6b7 ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ae073f59 ]
When innerprotoinherit is set, the tunneled packets do not have an inner
Ethernet header.
Change 'maclen' to not always assume the header length is ETH_HLEN, as
there might not be a MAC header.
This resolves issues with drivers (e.g. mlx5, in
mlx5e_tx_tunnel_accel()) who rely on the skb inner network header offset
to be correct, and use it for TX offloads.
Fixes: d8a6213d70 ("geneve: fix header validation in geneve[6]_xmit_skb")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44711b786 ]
In lio_vf_rep_copy_packet() pg_info->page is compared to a NULL value,
but then it is unconditionally passed to skb_add_rx_frag() which looks
strange and could lead to null pointer dereference.
lio_vf_rep_copy_packet() call trace looks like:
octeon_droq_process_packets
octeon_droq_fast_process_packets
octeon_droq_dispatch_pkt
octeon_create_recv_info
...search in the dispatch_list...
->disp_fn(rdisp->rinfo, ...)
lio_vf_rep_pkt_recv(struct octeon_recv_info *recv_info, ...)
In this path there is no code which sets pg_info->page to NULL.
So this check looks unneeded and doesn't solve potential problem.
But I guess the author had reason to add a check and I have no such card
and can't do real test.
In addition, the code in the function liquidio_push_packet() in
liquidio/lio_core.c does exactly the same.
Based on this, I consider the most acceptable compromise solution to
adjust this issue by moving skb_add_rx_frag() into conditional scope.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f233f3279 ("liquidio: switchdev support for LiquidIO NIC")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 968fde8384 ]
Currently hns3 ring buffer init process would hold cpu too long with big
Tx/Rx ring depth. This could cause soft lockup.
So this patch adds cond_resched() to the process. Then cpu can break to
run other tasks instead of busy looping.
Fixes: a723fb8efe ("net: hns3: refine for set ring parameters")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12cda92021 ]
When link status change, the nic driver need to notify the roce
driver to handle this event, but at this time, the roce driver
may uninit, then cause kernel crash.
To fix the problem, when link status change, need to check
whether the roce registered, and when uninit, need to wait link
update finish.
Fixes: 45e92b7e4e ("net: hns3: add calling roce callback function when link status change")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96b293315 ]
If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will
not be run. As a consequence, `sfp_hwmon_remove()` is not getting
run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()`
itself checks `sfp->sm_mod_state` anyways, so this check was not
really needed in the first place.
Fixes: d2e816c029 ("net: sfp: handle module remove outside state machine")
Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f4d93b78a upstream.
gve_rx_free_skb incorrectly leaves napi->skb referencing an skb after it
is freed with dev_kfree_skb_any(). This can result in a subsequent call
to napi_get_frags returning a dangling pointer.
Fix this by clearing napi->skb before the skb is freed.
Fixes: 9b8dd5e5ea ("gve: DQO: Add RX path")
Cc: stable@vger.kernel.org
Reported-by: Shailend Chand <shailend@google.com>
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Shailend Chand <shailend@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Link: https://lore.kernel.org/r/20240612001654.923887-1-ziweixiao@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21ae74e1bf ]
If ath10k_snoc is built-in, while Qualcomm remoteprocs are built as
modules, compilation fails with:
/usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/ath/ath10k/snoc.o: in function `ath10k_modem_init':
drivers/net/wireless/ath/ath10k/snoc.c:1534: undefined reference to `qcom_register_ssr_notifier'
/usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/ath/ath10k/snoc.o: in function `ath10k_modem_deinit':
drivers/net/wireless/ath/ath10k/snoc.c:1551: undefined reference to `qcom_unregister_ssr_notifier'
Add corresponding dependency to ATH10K_SNOC Kconfig entry so that it's
built as module if QCOM_RPROC_COMMON is built as module too.
Fixes: 747ff7d3d7 ("ath10k: Don't always treat modem stop events as crashes")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240511-ath10k-snoc-dep-v1-1-9666e3af5c27@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0c9a26435 ]
In case of region creation fail in ipc_devlink_create_region(), previously
created regions delete process starts from tainted pointer which actually
holds error code value.
Fix this bug by decreasing region index before delete.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 4dcd183fbd ("net: wwan: iosm: devlink registration")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240604082500.20769-1-amishin@t-argos.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adbf5a4234 ]
Referenced commit has introduced a bitmap to distinguish between ZC and
copy-mode AF_XDP queues, because xsk_get_pool_from_qid() does not do this
for us.
The bitmap would be especially useful when restoring previous state after
rebuild, if only it was not reallocated in the process. This leads to e.g.
xdpsock dying after changing number of queues.
Instead of preserving the bitmap during the rebuild, remove it completely
and distinguish between ZC and copy-mode queues based on the presence of
a device associated with the pool.
Fixes: e102db780e ("ice: track AF_XDP ZC enabled queues in bitmap")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-3-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad667d6268 ]
We all know they are redundant.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: adbf5a4234 ("ice: remove af_xdp_zc_qps bitmap")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16dfa49406 ]
To support new devlink-rate API ice_sched_node struct needs to store
a number of additional parameters. This includes tx_max, tx_share,
tx_weight, and tx_priority.
Add new fields to ice_sched_node struct. Add new functions to configure
the hardware with new parameters. Introduce new xarray to identify
nodes uniquely.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: adbf5a4234 ("ice: remove af_xdp_zc_qps bitmap")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03e4a092be ]
The ice_get_pfa_module_tlv() function iterates over the Type-Length-Value
structures in the Preserved Fields Area (PFA) of the NVM. This is used by
the driver to access data such as the Part Board Assembly identifier.
The function uses simple logic to iterate over the PFA. First, the pointer
to the PFA in the NVM is read. Then the total length of the PFA is read
from the first word.
A pointer to the first TLV is initialized, and a simple loop iterates over
each TLV. The pointer is moved forward through the NVM until it exceeds the
PFA area.
The logic seems sound, but it is missing a key detail. The Preserved
Fields Area length includes one additional final word. This is documented
in the device data sheet as a dummy word which contains 0xFFFF. All NVMs
have this extra word.
If the driver tries to scan for a TLV that is not in the PFA, it will read
past the size of the PFA. It reads and interprets the last dummy word of
the PFA as a TLV with type 0xFFFF. It then reads the word following the PFA
as a length.
The PFA resides within the Shadow RAM portion of the NVM, which is
relatively small. All of its offsets are within a 16-bit size. The PFA
pointer and TLV pointer are stored by the driver as 16-bit values.
In almost all cases, the word following the PFA will be such that
interpreting it as a length will result in 16-bit arithmetic overflow. Once
overflowed, the new next_tlv value is now below the maximum offset of the
PFA. Thus, the driver will continue to iterate the data as TLVs. In the
worst case, the driver hits on a sequence of reads which loop back to
reading the same offsets in an endless loop.
To fix this, we need to correct the loop iteration check to account for
this extra word at the end of the PFA. This alone is sufficient to resolve
the known cases of this issue in the field. However, it is plausible that
an NVM could be misconfigured or have corrupt data which results in the
same kind of overflow. Protect against this by using check_add_overflow
when calculating both the maximum offset of the TLVs, and when calculating
the next_tlv offset at the end of each loop iteration. This ensures that
the driver will not get stuck in an infinite loop when scanning the PFA.
Fixes: e961b679fb ("ice: add board identifier info to devlink .info_get")
Co-developed-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-1-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 229bedbf62 ]
In case of flow rule creation fail in mlx5_lag_create_port_sel_table(),
instead of previously created rules, the tainted pointer is deleted
deveral times.
Fix this bug by using correct flow rules pointers.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 352899f384 ("net/mlx5: Lag, use buckets in hash mode")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240604100552.25201-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2059cf51f3 ]
mlx5_cmd_init_hca() is taking ~0.2 seconds. In case of a user who
desire to disable some of the SF aux devices, and with large scale-1K
SFs for example, this user will waste more than 3 minutes on
mlx5_cmd_init_hca() which isn't needed at this stage.
Downstream patch will change SFs which are probe over the E-switch,
local SFs, to be probed without any aux dev. In order to support this,
split function_setup() to avoid executing mlx5_cmd_init_hca().
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: c8b3f38d2d ("net/mlx5: Always stop health timer during driver removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33afbfcc10 ]
In case pci channel becomes offline the driver should not wait for PCI
reads during health dump and recovery flow. The driver has timeout for
each of these loops trying to read PCI, so it would fail anyway.
However, in case of recovery waiting till timeout may cause the pci
error_detected() callback fail to meet pci_dpc_recovered() wait timeout.
Fixes: b3bd076f75 ("net/mlx5: Report devlink health on FW fatal issues")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ff38e730c ]
If driver teardown is called while PCI is turned off, there is a race
between health recovery and teardown. If health recovery already started
it will wait 60 sec trying to see if PCI gets back and it can recover,
but actually there is no need to wait anymore once teardown was called.
Use the MLX5_BREAK_FW_WAIT flag which is set on driver teardown to break
waiting for PCI up.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20230314054234.267365-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 33afbfcc10 ("net/mlx5: Stop waiting for PCI if pci channel is offline")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cd4bc987a ]
Commit f58f45c1e5 ("vxlan: drop packets from invalid src-address")
has recently been added to vxlan mainly in the context of source
address snooping/learning so that when it is enabled, an entry in the
FDB is not being created for an invalid address for the corresponding
tunnel endpoint.
Before commit f58f45c1e5 vxlan was similarly behaving as geneve in
that it passed through whichever macs were set in the L2 header. It
turns out that this change in behavior breaks setups, for example,
Cilium with netkit in L3 mode for Pods as well as tunnel mode has been
passing before the change in f58f45c1e5 for both vxlan and geneve.
After mentioned change it is only passing for geneve as in case of
vxlan packets are dropped due to vxlan_set_mac() returning false as
source and destination macs are zero which for E/W traffic via tunnel
is totally fine.
Fix it by only opting into the is_valid_ether_addr() check in
vxlan_set_mac() when in fact source address snooping/learning is
actually enabled in vxlan. This is done by moving the check into
vxlan_snoop(). With this change, the Cilium connectivity test suite
passes again for both tunnel flavors.
Fixes: f58f45c1e5 ("vxlan: drop packets from invalid src-address")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Bauer <mail@david-bauer.net>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
