[ Upstream commit c5b8d2c370 ]
The netc_blk_ctrl is controlled by the imx95-blk-ctl clock driver and
provides relevant clock configurations for NETC, SAI and MQS. Its address
length should be 8 bytes instead of 0x1000.
Fixes: 7764fef26e ("arm64: dts: imx95: Add NETCMIX block control support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e60b14f47d upstream.
For both the controller instances, size of the 'addr_space' region should
be 0x1fe00000 as per the hardware memory layout.
Otherwise, endpoint drivers cannot request even reasonable BAR size of 1MB.
Cc: stable@vger.kernel.org # 6.11
Fixes: c5f5de8434 ("arm64: dts: qcom: sa8775p: Add ep pcie1 controller node")
Fixes: 1924f55182 ("arm64: dts: qcom: sa8775p: Add ep pcie0 controller node")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241128145147.145618-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb8e7b33c2 upstream.
As per memory map table, the region for PCIe6a is 64MByte. Hence, set the
size of 32 bit non-prefetchable memory region beginning on address
0x70300000 as 0x3d00000 so that BAR space assigned to BAR registers can be
allocated from 0x70300000 to 0x74000000.
Fixes: 7af1418500 ("arm64: dts: qcom: x1e80100: Fix up BAR spaces")
Cc: stable@vger.kernel.org
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241113080508.3458849-1-quic_qianyu@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 058387d9c6 ]
Set the cache-line-size parameter of the L2 cache for each core to the
correct value of 64 bytes.
Previously, the L2 cache line size was incorrectly set to 128 bytes
for the Broadcom BCM2712. This causes validation tests for the
Performance Application Programming Interface (PAPI) tool to fail as
they depend on sysfs accurately reporting cache line sizes.
The correct value of 64 bytes is stated in the official documentation of
the ARM Cortex A-72, which is linked in the comments of
arm64/boot/dts/broadcom/bcm2712.dtsi as the source for cache-line-size.
Fixes: faa3381267 ("arm64: dts: broadcom: Add minimal support for Raspberry Pi 5")
Signed-off-by: Willow Cunningham <willow.e.cunningham@maine.edu>
Link: https://lore.kernel.org/r/20241007212954.214724-1-willow.e.cunningham@maine.edu
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6c5789c9d2 upstream.
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: a39ed23bdf ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbcc95fceb upstream.
The reset line of the IT6505 bridge chip is active low, not active high.
It was incorrectly inverted in the device tree as the implementation at
the time incorrectly inverted the polarity in its driver, due to a prior
device having an inline inverting level shifter.
Fix the polarity now while the external display pipeline is incomplete,
thereby avoiding any impact to running systems.
A matching fix for the driver should be included if this change is
backported.
Fixes: 8855d01fb8 ("arm64: dts: mediatek: Add MT8186 Krabby platform based Tentacruel / Tentacool")
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20241029100226.660263-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2213ca5199 upstream.
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: 316b80246b ("arm64: dts: ti: add verdin am62")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20241024130628.49650-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ca7699c37 upstream.
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f1aab0cb0 upstream.
The GPU SRAM supply is supposed to be always at least 0.1V higher than
the GPU supply. However when the DT was upstreamed, the spread was
incorrectly set to 0.01V.
Fixes: 8855d01fb8 ("arm64: dts: mediatek: Add MT8186 Krabby platform based Tentacruel / Tentacool")
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241021140537.3049232-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2496b2aaac upstream.
The way InvenSense MPU-6050 accelerometer is mounted on the user-facing side
of the Pine64 PinePhone mainboard, which makes it rotated 90 degrees counter-
clockwise, [1] requires the accelerometer's x- and y-axis to be swapped, and
the direction of the accelerometer's y-axis to be inverted.
Rectify this by adding a mount-matrix to the accelerometer definition in the
Pine64 PinePhone dtsi file.
[1] https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20bottom%20placement%20v1.1%2020191031.pdf
Fixes: 91f480d409 ("arm64: dts: allwinner: Add initial support for Pine64 PinePhone")
Cc: stable@vger.kernel.org
Suggested-by: Ondrej Jirman <megi@xff.cz>
Suggested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://patch.msgid.link/129f0c754d071cca1db5d207d9d4a7bd9831dff7.1726773282.git.dsimic@manjaro.org
[wens@csie.org: Replaced Helped-by with Suggested-by]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26ea2459d1 upstream.
The Voltorb device uses a speaker codec different from the original
Corsola device. When the Voltorb device tree was first added, the new
codec was added as a separate node when it should have just replaced the
existing one.
Merge the two nodes. The only differences are the compatible string and
the GPIO line property name. This keeps the device node path for the
speaker codec the same across the MT8186 Chromebook line. Also rename
the related labels and node names from having rt1019p to speaker codec.
Cc: stable@vger.kernel.org # v6.11+
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241018082113.1297268-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5df3068441 ]
Comply with bindings guidelines and get rid of errors such as:
cpufreq@18323000: compatible: 'oneOf' conditional failed, one must be fixed:
['qcom,cpufreq-hw'] is too short
Fixes: 8575f197b0 ("arm64: dts: qcom: Introduce the SC8180x platform")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42d8555752 ]
Correct the audio name for the Indiedroid Nova from
rockchip,es8388-codec to rockchip,es8388. This name change corrects a
kernel log error of "ASoC: driver name too long 'rockchip,es8388-codec'
-> 'rockchip_es8388'".
Fixes: 3900160e16 ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20241031150505.967909-2-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaecb1da58 ]
When the fixed regulators for the LCD panel and DP bridge were added,
their supplies were not modeled in. These, except for the 1.0V supply,
are just load switches, and need and have a supply.
Add the supplies for each of the fixed regulators.
Fixes: cabc71b08e ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20241030070224.1006331-4-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4e8cf13f1 ]
Some of the regulator supplies for the MIPI-DPI-to-DP bridge and their
associated nodes are incorrectly named. In particular, the 1.0V supply
was modeled as a 1.2V supply.
Fix all the incorrect names, and also fix the voltage of the 1.0V
regulator.
Fixes: cabc71b08e ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20241030070224.1006331-3-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76ab2ae0ab ]
Fix DTBS check errors for 'mt6358codec' and 'mt6358regulator':
Error message is:
pmic: 'mt6358codec' and 'mt6358regulator' does not match any of the
regexes: 'pinctrl-[0-9]+'.
Rename these two device node to generic 'audio-codec' and 'regulators'.
Fixes: 9f88722216 ("arm64: dts: mt6358: add PMIC MT6358 related nodes")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20241029064647.13370-1-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c771d311b1 ]
Fix the issue where both 'output-low' and 'output-high' exist under GPIO
hog nodes (rst_usb_hub_hog and sel_usb_hub_hog) when applying device
tree overlays. Since /delete-property/ is not supported in the overlays,
setting 'output-low' results in both properties being present. The
workaround is to disable these hogs and create new ones with 'output-low'
as needed.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtb: sel-usb-hub-hog:
{'output-low': True, 'gpio-hog': True, 'gpios': [[1, 0]], 'output-high': True, 'phandle': 108, '$nodename': ['sel-usb-hub-hog']}
is valid under each of {'required': ['output-low']}, {'required': ['output-high']
Fixes: 3f6fc30abe ("arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc926e3fa ]
"#sound-dai-cells" is required if the board is using "simple-card".
However, the HiHope board uses "audio-graph", thus remove the unneeded
`#sound-dai-cells`.
Commit 9e72606cd2 ("arm64: dts: renesas: #sound-dai-cells is used when
simple-card") updated the comment regarding usage of "#sound-dai-cells"
in the SoC DTSI but missed to remove "#sound-dai-cells" from board DTS
files.
Fixes: 9e72606cd2 ("arm64: dts: renesas: #sound-dai-cells is used when simple-card")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/20241010135332.710648-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e65616ef0 ]
Update the numbers based on the information found in the DSDT.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240716-topic-h_bits-v1-2-f6c5d3ff982c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a47e38167 ]
The clock IDs for multiple MCSPI instances across wakeup as
well as main domain in J7200 are incorrect when compared with
documentation [1]. This results in kernel crashes when the said
instances are enabled. Fix the clock ids to their appropriate
values.
[1]https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j7200/clocks.html
Fixes: 8f6c475f4c ("arm64: dts: ti: k3-j7200: Add MCSPI nodes")
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Link: https://lore.kernel.org/r/20241023104532.3438851-2-a-dutta@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7af8b4acb ]
Commit 0d0a0b4413 ("arm64: dts: ti: k3-j7200: fix main pinmux
range") split the main_pmx0 into two nodes: main_pmx0 and main_pmx1
due to a non-addressable region, but incorrectly represented the
ranges. As a result, the memory map for the pinctrl is incorrect. Fix
this by introducing the correct ranges.
The ranges are taken from the J7200 TRM [1] (Table 5-695. CTRL_MMR0
Registers).
Padconfig starting addresses and ranges:
- 0 to 66: 0x11c000, 0x10c
- 68: 0x11c110, 0x004
- 71 to 73: 0x11c11c, 0x00c
- 89 to 90: 0x11c164, 0x008
The datasheet [2] doesn't contain PADCONFIG63 (Table 6-106. Pin
Multiplexing), but the pin is necessary for enabling the MMC1 CLKLP
pad loopback and should be included in the pinmux register map.
Due to the change in pinmux node addresses, change the pinmux node for
the USB0_DRVVBUS pin to main_pmx2. The offset has not changed since the
new main_pmx2 node has the same base address and range as the original
main_pmx1 node. All other pinmuxing done within J7200 dts or dtso files
only uses main_pmx0 which has not changed.
[1] https://www.ti.com/lit/pdf/spruiu1
[2] https://www.ti.com/lit/gpn/dra821u
Fixes: 0d0a0b4413 ("arm64: dts: ti: k3-j7200: fix main pinmux range")
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240926102533.398139-1-a-limaye@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9d7e6596 ]
The 'enable-active-low' property is not a valid, because it is the
default behaviour of the fixed regulator.
Only 'enable-active-high' is valid, and when this property is absent
the fixed regulator will act as active low by default.
Both the rk3588-orange-pi-5 and the Wolfvision pf5 io expander overlay
smuggled those enable-active-low properties in, so remove them to
make dtbscheck happier.
Fixes: 28799a7734 ("arm64: dts: rockchip: add wolfvision pf5 io expander board")
Cc: Michael Riesch <michael.riesch@wolfvision.net>
Fixes: b6bc755d80 ("arm64: dts: rockchip: Add Orange Pi 5")
Cc: Muhammed Efe Cetin <efectn@6tel.net>
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-10-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e57d3dc7b ]
The dtschema requires to specify common ancestor which all SDIO chips are
derived from, so add accordingly.
Fixes: a50d5dcd28 ("arm64: tegra: Wire up WiFi on Jetson TX1 module")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409030438.8tumAnp1-lkp@intel.com
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d5794e6d9 ]
The RT5682i and RT5682s drivers describe two DAIs: AIF1 supports both
playback and capture, while AIF2 supports capture only.
Cherry doesn't specify which DAI to use. Although this doesn't cause
real issues because AIF1 happens to be the first DAI, it should be
corrected:
codec@1a: #sound-dai-cells: 1 was expected
Update #sound-dai-cells to 1 and adjust DAI link usages accordingly.
Fixes: 87728e3ccf ("arm64: dts: mediatek: mt8195-cherry: Specify sound DAI links and routing")
Signed-off-by: Fei Shao <fshao@chromium.org>
Link: https://lore.kernel.org/r/20241021114318.1358681-1-fshao@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bb64877a4 ]
The T-PHY controller at 0x11e40000 controls two underlying USB2 and USB3
PHY ports. The USB3 port works normally just like the others, so there's
no point in disabling it separately. Otherwise, board DTs would have to
enable both the T-PHY controller and one of its sub-nodes in particular,
which is slightly redundant and confusing.
Remove the status line in the u3port1 node, so it's ready to be used
once the T-PHY controller is enabled.
Fixes: 9461e0caac ("arm64: dts: Add MediaTek MT8188 dts and evaluation board and Makefile")
Signed-off-by: Fei Shao <fshao@chromium.org>
Link: https://lore.kernel.org/r/20241021081311.543625-1-fshao@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f766fae08f ]
The Hana device has a second source option trackpad, but it is missing
its regulator supply. It only works because the regulator is marked as
always-on.
Add the regulator supply, but leave out the post-power-on delay. Instead,
document the post-power-on delay along with the reason for not adding
it in a comment.
Fixes: 689b937bed ("arm64: dts: mediatek: add mt8173 elm and hana board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241018082001.1296963-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c33a0a02a2 ]
Drop the McASP AFIFOs for better audio latency. This adds back a
change that was lost while refactoring the device tree.
Fixes: 554dd562a5 ("arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Drop McASP AFIFOs")
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241002224754.2917895-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ed1a2b878 ]
Resize the GICR register region as it currently seeps into the CPU Control
Processor mailbox RX region.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20240612124056.39230-4-quic_sibis@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dd7d9d41d ]
L10A, being a fixed regulator, should have min_voltage = max_voltage,
otherwise fixed rulator fails to probe. Fix the max_voltage range to be
equal to minimum.
Fixes: 4edbcf264f ("arm64: dts: qcom: sda660-ifc6560: document missing USB PHY supplies")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240907-sdm660-wifi-v1-4-e316055142f8@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 377548f05b ]
Commit 009d855a26 ("arm64: dts: mt8183: add dpi node to mt8183") adds
a device-tree node for the DPI display interface that feeds the external
display pipeline, to enable HDMI support on the Pumpkin board.
However, the external display is not fully described on Chrome devices,
blocked by further work on DP / USB-C muxing graph bindings. This
incomplete description currently breaks internal display at least on the
Cozmo board. The same issue was found and fixed on MT8186 devices with
commit 3079fb09dd ("arm64: dts: mediatek: mt8186-corsola: Disable DPI
display interface"), but the MT8183 change wasn't merged until then.
Disable the external display interface for the Kukui device family until
the necessary work is done, like in the MT8186 Corsola case.
Fixes: 009d855a26 ("arm64: dts: mt8183: add dpi node to mt8183")
Link: https://lore.kernel.org/linux-mediatek/20240821042836.2631815-1-wenst@chromium.org/
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240916162956.267340-1-alpernebiyasak@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c14ab45f5d ]
The infracfg_ao node in mt8195.dtsi was causing a dtbs_check error.
The error message was:
syscon@10001000: compatible: ['mediatek,mt8195-infracfg_ao', 'syscon',
'simple-mfd'] is too long
To resolve this, remove 'simple-mfd' from the 'compatible' property of the
infracfg_ao node.
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241002051620.2050-1-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fc557b539 ]
The mutex node in mt8195.dtsi was triggering a dtbs_check error:
mutex@1c101000: 'clock-names', 'reg-names' do not match any of the
regexes: 'pinctrl-[0-9]+'
This seems no need by inspecting the DT schemas and other reference boards,
so drop 'clock-names' and 'reg-names' in mt8195.dtsi.
Fixes: 92d2c23dc2 ("arm64: dts: mt8195: add display node for vdosys1")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241002051620.2050-4-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 752804acea ]
The ethernet-phy node in mt8395-genio-1200-evk.dts was triggering a
dtbs_check error. The error message was:
eth-phy0@1: $nodename:0: 'eth-phy0@1' does not match
'^ethernet-phy(@[a-f0-9]+)?$'
Fix this issue by replacing 'eth-phy' node to generic 'ethernet-phy'.
Fixes: f2b543a191 ("arm64: dts: mediatek: add device-tree for Genio 1200 EVK board")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241002051620.2050-3-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4007651c25 ]
The clock index "CLK_APMIXED_MFGPLL" belongs to the "apmixedsys" provider,
so fix the index.
In addition, add a "mfg1" label so following commits could set
domain-supply for MFG1 power domain.
Fixes: eaf73e4224 ("arm64: dts: mediatek: mt8188: Add support for SoC power domains")
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241002022138.29241-2-pablo.sun@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6317aad0e1 ]
Newer boards should always use squashed MBN firmware instead of split
MDT+bNN. Use qcom/qcs6490/modem.mbn as the firmware for the modem on
RB3gen2.
Fixes: ac6d35b9b7 ("arm64: dts: qcom: qcs6490-rb3gen2: Enable various remoteprocs")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240907-rb3g2-fixes-v1-1-eb9da98e9f80@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bring a range of PCIe fixes across the X Elite platform, as well as
marking the NVMe power supply boot-on to avoid glitching the power
supply during boot.
The X Elite CRD audio configuration sees a spelling mistake corrected.
On SM8450 the PCIe 1 PIPE clock definition is corrected, to fix a
regression where this isn't able to acquire it's clocks.
-----BEGIN PGP SIGNATURE-----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=gD69
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmck734ACgkQYKtH/8kJ
UiejvA//edyTKEHQyY0rfTnQ8/aD2/l1DL2gTKPFIEB70i2UPdcxPBaWa74JBJVK
7C5zq5H4NpdW1J5NCcbZpmQZYfGnQ9ZtcaJt07fC/sdMl6lFwCiKVfAAPnwQwep1
QCrfbzEI1x44mYzZ+n4yrZXlL5k7stSuQ30ZdXuzVg5DquADSQsRgSkg88Xs923+
3laEX2J9iX5YbcqqgZ+wDhj/US6IPHBUasfHZjdsciUKMwH3yMiyfRLmB/sHxG/0
QTah4UUBVyonT3L43ECD/z1ElxFjHS6h/RKJmF8zHgIyxCbbabIYKGH0CR3LGUfZ
tm+DursZYILoJ7ccYYcKzJgybruqCweKwD13W6OaztluxMVyveSD2b+xU6aR+xYU
xQQQpwbMi4w9y9CDdjEBjQkTXVYH6RHPuYwsqu7rRsHcezmH8SITgWJi9/Y/6xA/
WTq3X6sOzJZwUhAo3I7usLjX7zLZkOkbHieBPti1M1V21EQrxFUxSEI1pMkAP42o
xiZ4jBHBCyGACsAbzXo1QxpdgfuPc9UYa5tlZ4Rajc7SFHQZUSvDBbVpcnp/rLh3
Bl74GN5SzVLb8sPrrLiFYTf9mzubURO3nNAikZ0TIsp3b4czZJ+o8NZLrkwID2iZ
Bfuq0vBd1rJdd1ChfGPfFtlR6aJrDFH9N3Ak/03v16LRsf1zc5A=
=1j8j
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-fixes-for-6.12-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into HEAD
More Qualcomm Arm64 DeviceTree fixes for v6.12
Bring a range of PCIe fixes across the X Elite platform, as well as
marking the NVMe power supply boot-on to avoid glitching the power
supply during boot.
The X Elite CRD audio configuration sees a spelling mistake corrected.
On SM8450 the PCIe 1 PIPE clock definition is corrected, to fix a
regression where this isn't able to acquire it's clocks.
* tag 'qcom-arm64-fixes-for-6.12-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: x1e80100: fix PCIe5 interconnect
arm64: dts: qcom: x1e80100: fix PCIe4 interconnect
arm64: dts: qcom: x1e80100: Fix up BAR spaces
arm64: dts: qcom: x1e80100-qcp: fix nvme regulator boot glitch
arm64: dts: qcom: x1e80100-microsoft-romulus: fix nvme regulator boot glitch
arm64: dts: qcom: x1e80100-yoga-slim7x: fix nvme regulator boot glitch
arm64: dts: qcom: x1e80100-vivobook-s15: fix nvme regulator boot glitch
arm64: dts: qcom: x1e80100-crd: fix nvme regulator boot glitch
arm64: dts: qcom: x1e78100-t14s: fix nvme regulator boot glitch
arm64: dts: qcom: x1e80100-crd Rename "Twitter" to "Tweeter"
arm64: dts: qcom: x1e80100: Fix PCIe 6a lanes description
arm64: dts: qcom: sm8450 fix PIPE clock specification for pcie1
arm64: dts: qcom: x1e80100: Add Broadcast_AND region in LLCC block
arm64: dts: qcom: x1e80100: fix PCIe5 PHY clocks
arm64: dts: qcom: x1e80100: fix PCIe4 and PCIe6a PHY clocks
Link: https://lore.kernel.org/r/20241101143206.738617-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
