commit d0fef6de4f upstream.
It is necessary to account for I2C quirks in the burst mode path of this
driver. Not all I2C controllers can accept arbitrarily long writes and this
is represented in the quirks field of the adapter structure.
Prior to this patch the following error message is seen on a Qualcomm
X1E80100 CRD.
[ 38.773524] i2c i2c-2: adapter quirk: msg too long (addr 0x0036, size 290, write)
[ 38.781454] ov08x40 2-0036: Failed regs transferred: -95
[ 38.787076] ov08x40 2-0036: ov08x40_start_streaming failed to set regs
Fix the error by breaking up the write sequence into the advertised maximum
write size of the quirks field if the quirks field is populated.
Fixes: 8f667d2023 ("media: ov08x40: Reduce start streaming time")
Cc: stable@vger.kernel.org # v6.9+
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6594d5076 upstream.
It is not valid to call pm_runtime_set_suspended() and
pm_runtime_set_active() for devices with runtime PM enabled because it
returns -EAGAIN if it is enabled already and working. So, adjust the
order to fix it.
Cc: stable@vger.kernel.org
Fixes: 5f9a089b6d ("dw9768: Enable low-power probe on ACPI")
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f070b1862 upstream.
The v4l2_detect_cvt/gtf functions should check the result against the
timing capabilities: these functions calculate the timings, so if they
are out of bounds, they should be rejected.
To do this, add the struct v4l2_dv_timings_cap as argument to those
functions.
This required updates to the adv7604 and adv7842 drivers since the
prototype of these functions has now changed. The timings struct
that is passed to v4l2_detect_cvt/gtf in those two drivers is filled
with the timings detected by the hardware.
The vivid driver was also updated, but an additional check was added:
the width and height specified by VIDIOC_S_DV_TIMINGS has to match the
calculated result, otherwise something went wrong. Note that vivid
*emulates* hardware, so all the values passed to the v4l2_detect_cvt/gtf
functions came from the timings struct that was filled by userspace
and passed on to the driver via VIDIOC_S_DV_TIMINGS. So these fields
can contain random data. Both the constraints check via
struct v4l2_dv_timings_cap and the additional width/height check
ensure that the resulting timings are sane and not messed up by the
v4l2_detect_cvt/gtf calculations.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Fixes: 2576415846 ("[media] v4l2: move dv-timings related code to v4l2-dv-timings.c")
Cc: stable@vger.kernel.org
Reported-by: syzbot+a828133770f62293563e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-media/000000000000013050062127830a@google.com/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24ad2d1f77 ]
The function ub960_rxport_read is being called and afterwards ret is
being checked for any failures, however ret is not being assigned to
the return of the function call. Fix this by assigning ret to the
return of the call which appears to be missing.
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d5c92cde4 ]
If cci_read() fails, 'st' is set to 0 in cci_read(), so we return success,
instead of the expected error code.
Fix it and return the expected error.
Fixes: 9a6d7f2ba2 ("media: i2c: st-vgxy61: Convert to CCI register access helpers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=SGfF
-----END PGP SIGNATURE-----
Merge tag 'media/v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- dvb-core fixes for vb2 check and device registration
- v4l2-core: fix an issue with error handling for VIDIOC_G_CTRL
- vb2 core: fix an issue with vb plane copy logic
- videobuf2-core: copy vb planes unconditionally
- vivid: fix buffer overwrite when using > 32 buffers
- vivid: fix a potential division by zero due to an issue at v4l2-tpg
- some spectre vulnerability fixes
- several OOM access fixes
- some buffer overflow fixes
* tag 'media/v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: videobuf2-core: copy vb planes unconditionally
media: dvbdev: fix the logic when DVB_DYNAMIC_MINORS is not set
media: vivid: fix buffer overwrite when using > 32 buffers
media: pulse8-cec: fix data timestamp at pulse8_setup()
media: cec: extron-da-hd-4k-plus: don't use -1 as an error code
media: stb0899_algo: initialize cfr before using it
media: adv7604: prevent underflow condition when reporting colorspace
media: cx24116: prevent overflows on SNR calculus
media: ar0521: don't overflow when checking PLL values
media: s5p-jpeg: prevent buffer overflows
media: av7110: fix a spectre vulnerability
media: mgb4: protect driver against spectre
media: dvb_frontend: don't play tricks with underflow values
media: dvbdev: prevent the risk of out of memory access
media: v4l2-tpg: prevent the risk of a division by zero
media: v4l2-ctrls-api: fix error handling for v4l2_g_ctrl()
media: dvb-core: add missing buffer index check
Currently, adv76xx_log_status() reads some date using
io_read() which may return negative values. The current logic
doesn't check such errors, causing colorspace to be reported
on a wrong way at adv76xx_log_status(), as reported by Coverity.
If I/O error happens there, print a different message, instead
of reporting bogus messages to userspace.
Fixes: 54450f591c ("[media] adv7604: driver for the Analog Devices ADV7604 video decoder")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
The PLL checks are comparing 64 bit integers with 32 bit
ones, as reported by Coverity. Depending on the values of
the variables, this may underflow.
Fix it ensuring that both sides of the expression are u64.
Fixes: 852b50aeed ("media: On Semi AR0521 sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Drop the redundant comma from mt9v111_of_match array to make the code
clean.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rectify the logical value of reset-gpio so that it is set to
0 (disabled) during power-on and to 1 (enabled) during power-off.
Set the reset-gpio to GPIO_OUT_HIGH at initialization time to make
sure it starts off in reset. Also drop the "Set XCLR" comment which
is not-so-informative.
The existing usage of imx335 had reset-gpios polarity inverted
(GPIO_ACTIVE_HIGH) in their device-tree sources. With this patch
included, those DTS will not be able to stream imx335 anymore. The
reset-gpio polarity will need to be rectified in the device-tree
sources as shown in [1] example, in order to get imx335 functional
again (as it remains in reset prior to this fix).
Cc: stable@vger.kernel.org
Fixes: 45d19b5fb9 ("media: i2c: Add imx335 camera sensor driver")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/linux-media/20240729110437.199428-1-umang.jain@ideasonboard.com/
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Omnivision OG01A1B camera sensor is supplied by three power rails,
if supplies are present as device properties, include them into
sensor power up sequence.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Omnivision OG01A1B camera sensor may have a connected active low GPIO
to XSHUTDOWN pad, and if so, include it into sensor power up sequence.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The OmniVision OG01A1B camera sensor has an xvclk supply clock, which
could be described and then explicitly controlled on OF platforms.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
[Sakari Ailus: Use UL specifier for power-up delay cycle value.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rearrange initializations and checks in probe before population of
the power management functions.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The OmniVision OG01A1B image sensor driver currently supports probing
only on ACPI platforms, the changes adds support of OF platforms to
the driver.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit 2989a45717 ("media: ccs: Refactor register reading a little")
removed ccs_read_addr_no_quirk() but left declaration.
Commit 529322112a ("media: ccs: Use V4L2 CCI for accessing sensor
registers") removed ccs_write_addr_no_quirk() and ccs_reg_width() but
leave their declarations.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The ov5675 specification says that the gap between XSHUTDN deassert and the
first I2C transaction should be a minimum of 8192 XVCLK cycles.
Right now we use a usleep_rage() that gives a sleep time of between about
430 and 860 microseconds.
On the Lenovo X13s we have observed that in about 1/20 cases the current
timing is too tight and we start transacting before the ov5675's reset
cycle completes, leading to I2C bus transaction failures.
The reset racing is sometimes triggered at initial chip probe but, more
usually on a subsequent power-off/power-on cycle e.g.
[ 71.451662] ov5675 24-0010: failed to write reg 0x0103. error = -5
[ 71.451686] ov5675 24-0010: failed to set plls
The current quiescence period we have is too tight. Instead of expressing
the post reset delay in terms of the current XVCLK this patch converts the
power-on and power-off delays to the maximum theoretical delay @ 6 MHz with
an additional buffer.
1.365 milliseconds on the power-on path is 1.5 milliseconds with grace.
85.3 microseconds on the power-off path is 90 microseconds with grace.
Fixes: 49d9ad719e ("media: ov5675: add device-tree support and support runtime PM")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Tested-by: Quentin Schulz <quentin.schulz@cherry.de> # RK3399 Puma with
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Analogous to e.g. the imx219 driver. This enables propagating the
V4L2_CID_CAMERA_SENSOR_ROTATION and V4L2_CID_CAMERA_ORIENTATION
values so that userspace - e.g. libcamera - can detect the
correct rotation and orientation from the device tree.
Signed-off-by: Robert Mader <robert.mader@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Coding style fixes suggested by Sakari during the
driver review.
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Coding style fixes suggested by Sakari during the
driver review.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Smatch is very confused by a clk_prepare_enable() being called in an
error-path. Fix this warning by moving the clk_prepare_enable() to its
own function.
drivers/media/i2c/tc358746.c:1631 tc358746_suspend() warn: 'tc358746->refclk' from clk_prepare_enable() not released on lines: 1631.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Smatch is very confused by a clk_prepare_enable() being called in an
error-path. Fix this warning by moving the clk_prepare_enable() to its
own function.
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1425 __s5c73m3_power_off() warn: 'state->clock' from clk_prepare_enable() not released on lines: 1425.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Factor out all the power off logic, except clk_disable_unprepare(), to a
new function __ov5645_set_power_off().
This allows ov5645_set_power_on() to excplicitly clean-out the clock
during the error-path.
The following smatch warning is fixed:
drivers/media/i2c/ov5645.c:690 ov5645_set_power_on() warn: 'ov5645->xclk' from clk_prepare_enable() not released on lines: 690.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Factor out all the power off logic, except the clk_disable_unprepare(),
to a new function __ar0521_power_off().
This allows ar0521_power_on() to explicitly clean-out the clock during
the error-path.
The following smatch warning is fixed:
drivers/media/i2c/ar0521.c:912 ar0521_power_on() warn: 'sensor->extclk' from clk_prepare_enable() not released on lines: 912.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop of_match_ptr() from mt9p031_i2c_driver and get rid of ugly CONFIG_OF
if check. This slightly increases the size of mt9p031_i2c_driver on non-OF
system and shouldn't be an issue.
Add mod_devicetable.h include.
It also allows, in case if needed, to enumerate this device via ACPI with
PRP0001 magic.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20230910160126.70122-3-biju.das.jz@bp.renesas.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The driver has an OF match table, still, it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumption that an I2C device registered via OF will always match a
legacy I2C device ID. The correct approach is to have an OF device ID
table using i2c_get_match_data() if the devices are registered via OF/ID.
Unify the OF/ID table by using MEDIA_BUS_FMT as match data for both these
tables and replace the ID lookup table for the match data by
i2c_get_match_data() and simplifly probe() and mt9p031_init_state().
While at it, remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other similar
things where the new entry goes _after_ the termination without the
compiler noticing.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20230910160126.70122-2-biju.das.jz@bp.renesas.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
`tda1997x_codec_driver` is not modified after its declaration, and it
is only passed to `devm_snd_soc_register_component()`, which expects
a constant `snd_soc_component_driver`.
Move `tda1997x_codec_driver` to a read-only section by declaring it
const.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is a spelling mistake in a string in the gc05a2_test_pattern_menu
array. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'vbi_ram_default' and 'tvp5150_config' are not modified in this diver
and are only used as a const struct.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
text data bss dec hex filename
57197 2936 36 60169 eb09 drivers/media/i2c/tvp5150.o
After:
text data bss dec hex filename
57517 2608 36 60161 eb01 drivers/media/i2c/tvp5150.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/i2c/uda1342.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use CCI_REG16_LE macro in order to access little-endian
encoded registers of the P3 (CSI) section.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
- Cleanups and fixes for the Renesas R-Car VSP and VIN drivers
- Miscellaneous cleanups to V4L2 core
-----BEGIN PGP SIGNATURE-----
iJgEABYKAEAWIQTAnvhxs4J7QT+XHKnMPy2AAyfeZAUCZnNeLCIcbGF1cmVudC5w
aW5jaGFydEBpZGVhc29uYm9hcmQuY29tAAoJEMw/LYADJ95kxyUBAKdQ86lXbVd1
97wtbRDP3H3MTtEowjskDGqhfH0QA9kXAP9eTf7rJixORvXFg/DaLcjdWIyfIsjY
4gz7aHO8MsXGBg==
=BgVa
-----END PGP SIGNATURE-----
Merge tag 'tags/next-media-renesas-20240619' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux.git
- Conversion of max9286 and adv748x to V4L2 subdev active state
- Cleanups and fixes for the Renesas R-Car VSP and VIN drivers
- Miscellaneous cleanups to V4L2 core
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
FW_LOADER config only selects the firmware loader API, but we also need
the sysfs_upload symbols for firmware_upload_unregister() and
firmware_upload_register() to function properly.
Fixes: 7a52ab415b ("media: i2c: Add driver for THine THP7312")
Cc: stable@vger.kernel.org
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Link: https://lore.kernel.org/r/20240620102544.1918105-1-kory.maincent@bootlin.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Add a V4L2 sub-device driver for Galaxycore GC05A2 image sensor.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
[Sakari Ailus: Fold in MAINTAINERS change.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a V4L2 sub-device driver for Galaxycore GC08A3 image sensor.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
[Sakari Ailus: Fold in MAINTAINERS change.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the frame interval stored in the subdev state instead of storing
a copy in the driver private structure.
Initialize the frame interval to the special case 0/0 that in the
max9286 driver represents automatic handling of frame sync.
As the frame sync mode is set at s_stream() time, we can remove it
from max9286_setup().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240617161135.130719-12-jacopo.mondi@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Use the subdev active state in the max9286 driver to store the
image format.
Replace the .open() function call with the .init_state() one and
simplify the set/get_pad_fmt() operations.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20240617161135.130719-11-jacopo.mondi@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The max9286 driver supports multiple output formats but only a single
one is reported through the .enum_mbus_code operation.
Fix that.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20240617161135.130719-10-jacopo.mondi@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
