[ Upstream commit b95102215a ]
Fix the suspend/resume path by ensuring the rtnl lock is held where
required. Calls to sh_eth_close, sh_eth_open and wol operations must be
performed under the rtnl lock to prevent conflicts with ongoing ndo
operations.
Fixes: b71af04676 ("sh_eth: add more PM methods")
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 752e5fcc2e ]
bgmac allocates new replacement buffer before handling each received
frame. Allocating & DMA-preparing 9724 B each time consumes a lot of CPU
time. Ideally bgmac should just respect currently set MTU but it isn't
the case right now. For now just revert back to the old limited frame
size.
This change bumps NAT masquerade speed by ~95%.
Since commit 8218f62c9c ("mm: page_frag: use initial zero offset for
page_frag_alloc_align()"), the bgmac driver fails to open its network
interface successfully and runs out of memory in the following call
stack:
bgmac_open
-> bgmac_dma_init
-> bgmac_dma_rx_skb_for_slot
-> netdev_alloc_frag
BGMAC_RX_ALLOC_SIZE = 10048 and PAGE_FRAG_CACHE_MAX_SIZE = 32768.
Eventually we land into __page_frag_alloc_align() with the following
parameters across multiple successive calls:
__page_frag_alloc_align: fragsz=10048, align_mask=-1, size=32768, offset=0
__page_frag_alloc_align: fragsz=10048, align_mask=-1, size=32768, offset=10048
__page_frag_alloc_align: fragsz=10048, align_mask=-1, size=32768, offset=20096
__page_frag_alloc_align: fragsz=10048, align_mask=-1, size=32768, offset=30144
So in that case we do indeed have offset + fragsz (40192) > size (32768)
and so we would eventually return NULL. Reverting to the older 1500
bytes MTU allows the network driver to be usable again.
Fixes: 8c7da63978 ("bgmac: configure MTU and add support for frames beyond 8192 byte size")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[florian: expand commit message about recent commits]
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250127175159.1788246-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 044f2fbaa2 ]
Tx/Rx FIFO size is specified by the parameter "{tx,rx}-fifo-depth" from
stmmac_platform layer.
However, these values are constrained by upper limits determined by the
capabilities of each hardware feature. There is a risk that the upper
bits will be truncated due to the calculation, so it's appropriate to
limit them to the upper limit values and display a warning message.
This only works if the hardware capability has the upper limit values.
Fixes: e7877f52fd ("stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5fb35a3d6 ]
The number of MTL queues to use is specified by the parameter
"snps,{tx,rx}-queues-to-use" from stmmac_platform layer.
However, the maximum numbers of queues are constrained by upper limits
determined by the capability of each hardware feature. It's appropriate
to limit the values not to exceed the upper limit values and display
a warning message.
This only works if the hardware capability has the upper limit values.
Fixes: d976a525c3 ("net: stmmac: multiple queues dt configuration")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e43ad7a1e ]
Ethtool ntuple filters with FLOW_RSS were originally defined as adding
the base queue ID (ring_cookie) to the value from the indirection table,
so that the same table could distribute over more than one set of queues
when used by different filters.
However, some drivers / hardware ignore the ring_cookie, and simply use
the indirection table entries as queue IDs directly. Thus, for drivers
which have not opted in by setting ethtool_ops.cap_rss_rxnfc_adds to
declare that they support the original (addition) semantics, reject in
ethtool_set_rxnfc any filter which combines FLOW_RSS and a nonzero ring.
(For a ring_cookie of zero, both behaviours are equivalent.)
Set the cap bit in sfc, as it is known to support this feature.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://patch.msgid.link/cc3da0844083b0e301a33092a6299e4042b65221.1731499022.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4f5a52adeb ("ethtool: Fix set RXNFC command with symmetric RSS hash")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19e65c45a1 ]
dm is netdev private data and it cannot be
used after free_netdev() call. Using dm after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
This is similar to the issue fixed in commit
ad297cd2db ("net: qcom/emac: fix UAF in emac_remove").
This bug is detected by our static analysis tool.
Fixes: cf9e60aa69 ("net: davicom: Fix regulator not turned off on driver removal")
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
CC: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250123214213.623518-1-chenyuan0y@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee7d79433d ]
First case:
> ip l a l $VF name vlanx type vlan id 100
> ip l d vlanx
> ip l a l $VF name vlanx type vlan id 100
As workqueue can be execute after sometime, there is a window to have
call trace like that:
- iavf_del_vlan
- iavf_add_vlan
- iavf_del_vlans (wq)
It means that our VLAN 100 will change the state from IAVF_VLAN_ACTIVE
to IAVF_VLAN_REMOVE (iavf_del_vlan). After that in iavf_add_vlan state
won't be changed because VLAN 100 is on the filter list. The final
result is that the VLAN 100 filter isn't added in hardware (no
iavf_add_vlans call).
To fix that change the state if the filter wasn't removed yet directly
to active. It is save as IAVF_VLAN_REMOVE means that virtchnl message
wasn't sent yet.
Second case:
> ip l a l $VF name vlanx type vlan id 100
Any type of VF reset ex. change trust
> ip l s $PF vf $VF_NUM trust on
> ip l d vlanx
> ip l a l $VF name vlanx type vlan id 100
In case of reset iavf driver is responsible for readding all filters
that are being used. To do that all VLAN filters state are changed to
IAVF_VLAN_ADD. Here is even longer window for changing VLAN state from
kernel side, as workqueue isn't called immediately. We can have call
trace like that:
- changing to IAVF_VLAN_ADD (after reset)
- iavf_del_vlan (called from kernel ops)
- iavf_del_vlans (wq)
Not exsisitng VLAN filters will be removed from hardware. It isn't a
bug, ice driver will handle it fine. However, we can have call trace
like that:
- changing to IAVF_VLAN_ADD (after reset)
- iavf_del_vlan (called from kernel ops)
- iavf_add_vlan (called from kernel ops)
- iavf_del_vlans (wq)
With fix for previous case we end up with no VLAN filters in hardware.
We have to remove VLAN filters if the state is IAVF_VLAN_ADD and delete
VLAN was called. It is save as IAVF_VLAN_ADD means that virtchnl message
wasn't sent yet.
Fixes: 0c0da0e951 ("iavf: refactor VLAN filter states")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5cc2a27e0 ]
It occurred that in the commit 70838938e8 ("ice: Implement driver
functionality to dump serdes equalizer values") the invalid DRATE parameter
for reading has been added. The output of the command:
$ ethtool -d <ethX>
returns the garbage value in the place where DRATE value should be
stored.
Remove mentioned parameter to prevent return of corrupted data to
userspace.
Fixes: 70838938e8 ("ice: Implement driver functionality to dump serdes equalizer values")
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99dbcab0cd ]
Extend the work done in commit 70838938e8 ("ice: Implement driver
functionality to dump serdes equalizer values") by adding the new set of
Rx registers that can be read using command:
$ ethtool -d interface_name
Rx equalization parameters are E810 PHY registers used by end user to
gather information about configuration and status to debug link and
connection issues in the field.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: c5cc2a27e0 ("ice: remove invalid parameter of equalizer")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ea085937d ]
Refactor function ice_get_tx_rx_equa() to iterate over new table of
params instead of multiple calls to ice_aq_get_phy_equalization().
Subsequent commit will extend that function by add more serdes equalizer
values to dump.
Shorten the fields of struct ice_serdes_equalization_to_ethtool for
readability purposes.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: c5cc2a27e0 ("ice: remove invalid parameter of equalizer")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18625e26fe ]
Fix &ice_parser_rt::bst_key size. It was wrongly set to 10 instead of 20
in the initial impl commit (see Fixes tag). All usage code assumed it was
of size 20. That was also the initial size present up to v2 of the intro
series [2], but halved by v3 [3] refactor described as "Replace magic
hardcoded values with macros." The introducing series was so big that
some ugliness was unnoticed, same for bugs :/
ICE_BST_KEY_TCAM_SIZE and ICE_BST_TCAM_KEY_SIZE were differing by one.
There was tmp variable @j in the scope of edited function, but was not
used in all places. This ugliness is now gone.
I'm moving ice_parser_rt::pg_prio a few positions up, to fill up one of
the holes in order to compensate for the added 10 bytes to the ::bst_key,
resulting in the same size of the whole as prior to the fix, and minimal
changes in the offsets of the fields.
Extend also the debug dump print of the key to cover all bytes. To not
have string with 20 "%02x" and 20 params, switch to
ice_debug_array_w_prefix().
This fix obsoletes Ahmed's attempt at [1].
[1] https://lore.kernel.org/intel-wired-lan/20240823230847.172295-1-ahmed.zaki@intel.com
[2] https://lore.kernel.org/intel-wired-lan/20230605054641.2865142-13-junfeng.guo@intel.com
[3] https://lore.kernel.org/intel-wired-lan/20230817093442.2576997-13-junfeng.guo@intel.com
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/intel-wired-lan/b1fb6ff9-b69e-4026-9988-3c783d86c2e0@stanley.mountain
Fixes: 9a4c07aaa0 ("ice: add parser execution main loop")
CC: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a5b021cb8 ]
When a workqueue is created with `WQ_UNBOUND`, its work items are
served by special worker-pools, whose host workers are not bound to
any specific CPU. In the default configuration (i.e. when
`queue_delayed_work` and friends do not specify which CPU to run the
work item on), `WQ_UNBOUND` allows the work item to be executed on any
CPU in the same node of the CPU it was enqueued on. While this
solution potentially sacrifices locality, it avoids contention with
other processes that might dominate the CPU time of the processor the
work item was scheduled on.
This is not just a theoretical problem: in a particular scenario
misconfigured process was hogging most of the time from CPU0, leaving
less than 0.5% of its CPU time to the kworker. The IDPF workqueues
that were using the kworker on CPU0 suffered large completion delays
as a result, causing performance degradation, timeouts and eventual
system crash.
Tested:
* I have also run a manual test to gauge the performance
improvement. The test consists of an antagonist process
(`./stress --cpu 2`) consuming as much of CPU 0 as possible. This
process is run under `taskset 01` to bind it to CPU0, and its
priority is changed with `chrt -pQ 9900 10000 ${pid}` and
`renice -n -20 ${pid}` after start.
Then, the IDPF driver is forced to prefer CPU0 by editing all calls
to `queue_delayed_work`, `mod_delayed_work`, etc... to use CPU 0.
Finally, `ktraces` for the workqueue events are collected.
Without the current patch, the antagonist process can force
arbitrary delays between `workqueue_queue_work` and
`workqueue_execute_start`, that in my tests were as high as
`30ms`. With the current patch applied, the workqueue can be
migrated to another unloaded CPU in the same node, and, keeping
everything else equal, the maximum delay I could see was `6us`.
Fixes: 0fe45467a1 ("idpf: add create vport and netdev configuration")
Signed-off-by: Marco Leogrande <leogrande@google.com>
Signed-off-by: Manoj Vishwanathan <manojvishy@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d15fe4edd7 ]
The transaction salt was being accessed before acquiring the
idpf_vc_xn_lock when idpf has to forward the virtchnl reply.
Fixes: 34c21fa894 ("idpf: implement virtchnl transaction manager")
Signed-off-by: Manoj Vishwanathan <manojvishy@google.com>
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 137da75ba7 ]
Restore the call to idpf_vc_xn_shutdown() at the beginning of
idpf_vc_core_deinit() provided the function is not called on remove.
In the reset path the mailbox is destroyed, leading to all transactions
timing out.
Fixes: 09d0fb5cb3 ("idpf: deinit virtchnl transaction manager after vport and vectors")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 396f016567 ]
Add read memory barrier to ensure the order of operations when accessing
control queue descriptors. Specifically, we want to avoid cases where loads
can be reordered:
1. Load #1 is dispatched to read descriptor flags.
2. Load #2 is dispatched to read some other field from the descriptor.
3. Load #2 completes, accessing memory/cache at a point in time when the DD
flag is zero.
4. NIC DMA overwrites the descriptor, now the DD flag is one.
5. Any fields loaded before step 4 are now inconsistent with the actual
descriptor state.
Add read memory barrier between steps 1 and 2, so that load #2 is not
executed until load #1 has completed.
Fixes: 8077c72756 ("idpf: add controlq init and reset checks")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Suggested-by: Lance Richardson <rlance@google.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a197004cf3 ]
When using temperature measurement on Marvell 88Q2XXX devices and the
reset-gpios property is set in DT, the device does a hardware reset when
interface is brought down and up again. That means that the content of
the register MDIO_MMD_PCS_MV_TEMP_SENSOR2 is reset to default and that
leads to permanent deactivation of the temperature measurement, because
activation is done in mv88q2xxx_probe. To fix this move activation of
temperature measurement to mv88q222x_config_init.
Fixes: a557a92e68 ("net: phy: marvell-88q2xxx: add support for temperature sensor")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250118-marvell-88q2xxx-fix-hwmon-v2-1-402e62ba2dcb@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92e5995773 ]
When unload hclge driver, it tries to disable sriov first for each
ae_dev node from hnae3_ae_dev_list. If user unloads hns3 driver at
the time, because it removes all the ae_dev nodes, and it may cause
oops.
But we can't simply use hnae3_common_lock for this. Because in the
process flow of pci_disable_sriov(), it will trigger the remove flow
of VF, which will also take hnae3_common_lock.
To fixes it, introduce a new mutex to protect the unload process.
Fixes: 0dd8a25f35 ("net: hns3: disable sriov before unload hclge layer")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250118094741.3046663-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d31a49d37c ]
Fix wrong GDM4 register definition, in Airoha SDK GDM4 is defined at
offset 0x2400 but this doesn't make sense as it does conflict with the
CDM4 that is in the same location.
Following the pattern where each GDM base is at the FWD_CFG, currently
GDM4 base offset is set to 0x2500. This is correct but REG_GDM4_FWD_CFG
and REG_GDM4_SRC_PORT_SET are still using the SDK reference with the
0x2400 offset. Fix these 2 define by subtracting 0x100 to each register
to reflect the real address location.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250120154148.13424-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4395a44acb ]
When getting the IRQ we use k3_udma_glue_tx_get_irq() which returns
negative error value on error. So not NULL check is not sufficient
to deteremine if IRQ is valid. Check that IRQ is greater then zero
to ensure it is valid.
There is no issue at probe time but at runtime user can invoke
.set_channels which results in the following call chain.
am65_cpsw_set_channels()
am65_cpsw_nuss_update_tx_rx_chns()
am65_cpsw_nuss_remove_tx_chns()
am65_cpsw_nuss_init_tx_chns()
At this point if am65_cpsw_nuss_init_tx_chns() fails due to
k3_udma_glue_tx_get_irq() then tx_chn->irq will be set to a
negative value.
Then, at subsequent .set_channels with higher channel count we
will attempt to free an invalid IRQ in am65_cpsw_nuss_remove_tx_chns()
leading to a kernel warning.
The issue is present in the original commit that introduced this driver,
although there, am65_cpsw_nuss_update_tx_rx_chns() existed as
am65_cpsw_nuss_update_tx_chns().
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70d81f25cc ]
Currently, mlxfw kernel module limits FW flash image size to be
10MB at most, preventing the ability to burn recent BlueField-3
FW that exceeds the said size limit.
Thus, drop the hard coded limit. Instead, rely on FW's
max_component_size threshold that is reported in MCQI register
as the size limit for FW image.
Fixes: 410ed13cae ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1737030796-1441634-1-git-send-email-moshe@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3440fa34ad ]
Following fields of 'struct mr_mfc' can be updated
concurrently (no lock protection) from ip_mr_forward()
and ip6_mr_forward()
- bytes
- pkt
- wrong_if
- lastuse
They also can be read from other functions.
Convert bytes, pkt and wrong_if to atomic_long_t,
and use READ_ONCE()/WRITE_ONCE() for lastuse.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250114221049.1190631-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da8352da1e ]
The non-AP interfaces would not use conf->vht_ldpc so they never set
STA_CAP_VHT_LDPC even if peer-station support LDPC.
Check conf->vht_ldpc only for AP interface.
Without this patch, station only uses BCC to transmit packet in VHT mode.
Fixes: dda423dd65 ("wifi: mt76: mt7996: remove mt7996_mcu_beacon_check_caps()")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-7-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14749fe2ed ]
For mt7992 chipsets, the definition of TXD.DW6.BIT10~15 has different
interpretations on different frame types. Driver only needs to fill
MSDU_CNT for non-management frames.
Fixes: 408566db8c ("wifi: mt76: connac: add new definition of tx descriptor")
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-6-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c2a25a1ab ]
Fix wrong calculation of the channel times due to incorrect
interpretation from the FW event.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-4-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e3aef59a4 ]
Set HE SU PPDU And HE MU PPDU With 4x HE-LTF And 0.8 us GI within HE PHY
Capabilities element as 1 since hardware can support.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-3-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ffbdfc1bd ]
This commit includes two changes. First, enable "EHT MU PPDU With 4x
EHT-LTF And 0.8us GI" in EHT Phy capabilities element since hardware
can support. Second, fix the value of "Maximum number of supported
EHT LTFs" in the same element, where the previous setting of 3 in
Bit 3-4 was incorrect.
Fixes: 348533eb96 ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-2-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1816ad9381 ]
Set max mpdu len to 11454 according to hardware capability.
Without this patch, the max ampdu length would be 3895 and count not get
expected performance.
Fixes: 348533eb96 ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250114101026.3587702-1-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d07ecb4f70 ]
Bypass the entry when ofs is equal to dev->reg.map[i].size.
Without this patch, it would get incorrect register mapping when the CR
address is located at the boundary of an entry.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Link: https://patch.msgid.link/OSZPR01MB84344FEFF53004B5CF40BCC198132@OSZPR01MB8434.jpnprd01.prod.outlook.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd1649ef96 ]
Bypass the entry when ofs is equal to dev->reg.map[i].size.
Without this patch, it would get incorrect register mapping when the CR
address is located at the boundary of an entry.
Fixes: cd4c314a65 ("mt76: mt7915: refine register definition")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Link: https://patch.msgid.link/OSZPR01MB843401EAA1DA6BD7AEF356F298132@OSZPR01MB8434.jpnprd01.prod.outlook.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b60e2ae51 ]
It seems that the firmware checks the register used for detecting matching
PCIe links in order to figure out if a secondary PCIe link is enabled.
Write the register again just before starting the firmware on hw reset,
in order to fix an issue that left the second band unusable after restart.
Fixes: 9093cfff72 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Link: https://patch.msgid.link/20241230194202.95065-11-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 349460913a ]
Properly retrieve the response for commands with events. Ensure accurate
handling of event-driven commands.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-17-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 816161051a ]
Clean up MLO settings after disconnection.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-16-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb2a9a12c6 ]
Update mt7925_mcu_uni_[tx,rx]_ba for MLO support in firmware.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-15-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dafab9c41 ]
Update the power-saving flow for secondary links.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-13-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30b721467c ]
Update mt7925_unassign_vif_chanctx to support per-link BSS.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-12-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90c10286b1 ]
Update mt792x_rx_get_wcid to support per-link STA.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-11-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e02f6ed6a ]
Update mt7925_mcu_sta_update for broadcast (BC) in the ASSOC state.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-10-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6803d39a8 ]
Enhance mt7925_mac_link_sta_add to support MLO.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-9-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac03e5b82b ]
In mt7925_mac_link_bss_add(), the mt76_connac_mcu_uni_add_dev() function
must be executed only after all parameters have been properly initialized.
Fixes: 86c051f2c4 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20241211011926.5002-8-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
