commit 9466545720 upstream.
Since commit c033563220
("usb: gadget: configfs: Attach arbitrary strings to cdev")
a user can provide extra string descriptors to a USB gadget via configfs.
For "manufacturer", "product", "serialnumber", setting the string via
configfs ignores a trailing LF.
For the arbitrary strings the LF was not ignored.
This patch ignores a trailing LF to make this consistent with the existing
behavior for "manufacturer", ... string descriptors.
Fixes: c033563220 ("usb: gadget: configfs: Attach arbitrary strings to cdev")
Cc: stable <stable@kernel.org>
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Link: https://lore.kernel.org/r/20241212154114.29295-1-ingo.rohloff@lauterbach.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfc51e48bc upstream.
This commit addresses an issue related to below kernel panic where
panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON
in functionsfs_bind, which easily leads to the following scenarios.
1.adb_write in adbd 2. UDC write via configfs
================= =====================
->usb_ffs_open_thread() ->UDC write
->open_functionfs() ->configfs_write_iter()
->adb_open() ->gadget_dev_desc_UDC_store()
->adb_write() ->usb_gadget_register_driver_owner
->driver_register()
->StartMonitor() ->bus_add_driver()
->adb_read() ->gadget_bind_driver()
<times-out without BIND event> ->configfs_composite_bind()
->usb_add_function()
->open_functionfs() ->ffs_func_bind()
->adb_open() ->functionfs_bind()
<ffs->state !=FFS_ACTIVE>
The adb_open, adb_read, and adb_write operations are invoked from the
daemon, but trying to bind the function is a process that is invoked by
UDC write through configfs, which opens up the possibility of a race
condition between the two paths. In this race scenario, the kernel panic
occurs due to the WARN_ON from functionfs_bind when panic_on_warn is
enabled. This commit fixes the kernel panic by removing the unnecessary
WARN_ON.
Kernel panic - not syncing: kernel: panic_on_warn set ...
[ 14.542395] Call trace:
[ 14.542464] ffs_func_bind+0x1c8/0x14a8
[ 14.542468] usb_add_function+0xcc/0x1f0
[ 14.542473] configfs_composite_bind+0x468/0x588
[ 14.542478] gadget_bind_driver+0x108/0x27c
[ 14.542483] really_probe+0x190/0x374
[ 14.542488] __driver_probe_device+0xa0/0x12c
[ 14.542492] driver_probe_device+0x3c/0x220
[ 14.542498] __driver_attach+0x11c/0x1fc
[ 14.542502] bus_for_each_dev+0x104/0x160
[ 14.542506] driver_attach+0x24/0x34
[ 14.542510] bus_add_driver+0x154/0x270
[ 14.542514] driver_register+0x68/0x104
[ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4
[ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144
[ 14.542526] configfs_write_iter+0xf0/0x138
Fixes: ddf8abd259 ("USB: f_fs: the FunctionFS driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Akash M <akash.m5@samsung.com>
Link: https://lore.kernel.org/r/20241219125221.1679-1-akash.m5@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 057bd54dfc upstream.
Currently afunc_bind sets std_ac_if_desc.bNumEndpoints to 1 if
controls (mute/volume) are enabled. During next afunc_bind call,
bNumEndpoints would be unchanged and incorrectly set to 1 even
if the controls aren't enabled.
Fix this by resetting the value of bNumEndpoints to 0 on every
afunc_bind call.
Fixes: eaf6cbe099 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20241211115915.159864-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f660ffce7 upstream.
We should do reverse selection of other components from
CONFIG_USB_F_MIDI2 which is tristate, instead of
CONFIG_USB_CONFIGFS_F_MIDI2 which is bool, for satisfying subtle
module dependencies.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250101131124.27599-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13014969cb upstream.
Considering that in some extreme cases, when performing the
unbinding operation, gserial_disconnect has cleared gser->ioport,
which triggers gadget reconfiguration, and then calls gs_read_complete,
resulting in access to a null pointer. Therefore, ep is disabled before
gserial_disconnect sets port to null to prevent this from happening.
Call trace:
gs_read_complete+0x58/0x240
usb_gadget_giveback_request+0x40/0x160
dwc3_remove_requests+0x170/0x484
dwc3_ep0_out_start+0xb0/0x1d4
__dwc3_gadget_start+0x25c/0x720
kretprobe_trampoline.cfi_jt+0x0/0x8
kretprobe_trampoline.cfi_jt+0x0/0x8
udc_bind_to_driver+0x1d8/0x300
usb_gadget_probe_driver+0xa8/0x1dc
gadget_dev_desc_UDC_store+0x13c/0x188
configfs_write_iter+0x160/0x1f4
vfs_write+0x2d0/0x40c
ksys_write+0x7c/0xf0
__arm64_sys_write+0x20/0x30
invoke_syscall+0x60/0x150
el0_svc_common+0x8c/0xf8
do_el0_svc+0x28/0xa0
el0_svc+0x24/0x84
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable <stable@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Link: https://lore.kernel.org/r/TYUPR06MB621733B5AC690DBDF80A0DCCD2042@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cfbca86f6 upstream.
Considering that in some extreme cases,
when u_serial driver is accessed by multiple threads,
Thread A is executing the open operation and calling the gs_open,
Thread B is executing the disconnect operation and calling the
gserial_disconnect function,The port->port_usb pointer will be set to NULL.
E.g.
Thread A Thread B
gs_open() gadget_unbind_driver()
gs_start_io() composite_disconnect()
gs_start_rx() gserial_disconnect()
... ...
spin_unlock(&port->port_lock)
status = usb_ep_queue() spin_lock(&port->port_lock)
spin_lock(&port->port_lock) port->port_usb = NULL
gs_free_requests(port->port_usb->in) spin_unlock(&port->port_lock)
Crash
This causes thread A to access a null pointer (port->port_usb is null)
when calling the gs_free_requests function, causing a crash.
If port_usb is NULL, the release request will be skipped as it
will be done by gserial_disconnect.
So add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port_usb.
Call trace:
gs_start_io+0x164/0x25c
gs_open+0x108/0x13c
tty_open+0x314/0x638
chrdev_open+0x1b8/0x258
do_dentry_open+0x2c4/0x700
vfs_open+0x2c/0x3c
path_openat+0xa64/0xc60
do_filp_open+0xb8/0x164
do_sys_openat2+0x84/0xf0
__arm64_sys_openat+0x70/0x9c
invoke_syscall+0x58/0x114
el0_svc_common+0x80/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x38/0x68
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable@vger.kernel.org
Suggested-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Acked-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/TYUPR06MB62178DC3473F9E1A537DCD02D2362@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8293705696 upstream.
The UMP Function Block info m1.0 field (represented by is_midi1 sysfs
entry) is an enumeration from 0 to 2, while the midi2 gadget driver
incorrectly copies it to the corresponding snd_ump_block_info.flags
bits as-is. This made the wrong bit flags set when m1.0 = 2.
This patch corrects the wrong interpretation of is_midi1 bits.
Fixes: 29ee7a4ddd ("usb: gadget: midi2: Add configfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20241127070213.8232-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51cdd69d6a upstream.
This reverts commit ec6ce7075e.
Fix installation of WinUSB driver using OS descriptors. Without the
fix the drivers are not installed correctly and the property
'DeviceInterfaceGUID' is missing on host side.
The original change was based on the assumption that the interface
number is in the high byte of wValue but it is in the low byte,
instead. Unfortunately, the fix is based on MS documentation which is
also wrong.
The actual USB request for OS descriptors (using USB analyzer) looks
like:
Offset 0 1 2 3 4 5 6 7
0x000 C1 A1 02 00 05 00 0A 00
C1: bmRequestType (device to host, vendor, interface)
A1: nas magic number
0002: wValue (2: nas interface)
0005: wIndex (5: get extended property i.e. nas interface GUID)
008E: wLength (142)
The fix was tested on Windows 10 and Windows 11.
Cc: stable@vger.kernel.org
Fixes: ec6ce7075e ("usb: gadget: composite: fix OS descriptors w_value logic")
Signed-off-by: Michal Vrastil <michal.vrastil@hidglobal.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Peter korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20241113235433.20244-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit adc292d54d ]
Since the req_free list will updated if enqueuing one request was not
possible it will be added back to the free list. With every available
free request in the queue it is a valid case for the pump worker to use
it and continue the pending bufferdata into requests for the req_ready
list.
Fixes: 6acba0345b ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-1-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The syzbot fuzzer has been encountering "task hung" problems ever
since the dummy-hcd driver was changed to use hrtimers instead of
regular timers. It turns out that the problems are caused by a subtle
difference between the timer_pending() and hrtimer_active() APIs.
The changeover blindly replaced the first by the second. However,
timer_pending() returns True when the timer is queued but not when its
callback is running, whereas hrtimer_active() returns True when the
hrtimer is queued _or_ its callback is running. This difference
occasionally caused dummy_urb_enqueue() to think that the callback
routine had not yet started when in fact it was almost finished. As a
result the hrtimer was not restarted, which made it impossible for the
driver to dequeue later the URB that was just enqueued. This caused
usb_kill_urb() to hang, and things got worse from there.
Since hrtimers have no API for telling when they are queued and the
callback isn't running, the driver must keep track of this for itself.
That's what this patch does, adding a new "timer_pending" flag and
setting or clearing it at the appropriate times.
Reported-by: syzbot+f342ea16c9d06d80b585@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/6709234e.050a0220.3e960.0011.GAE@google.com/
Tested-by: syzbot+f342ea16c9d06d80b585@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: a7f3813e58 ("usb: gadget: dummy_hcd: Switch to hrtimer transfer scheduler")
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/2dab644e-ef87-4de8-ac9a-26f100b2c609@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The configfs store callback should return the number of bytes consumed
not the total number of bytes we actually stored. These could differ if
for example the passed in string had a newline we did not store.
If the returned value does not match the number of bytes written the
writer might assume a failure or keep trying to write the remaining bytes.
For example the following command will hang trying to write the final
newline over and over again (tested on bash 2.05b):
echo foo > function_name
Fixes: 993a44fa85 ("usb: gadget: f_uac2: allow changing interface name via configfs")
Cc: stable <stable@kernel.org>
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20241006232637.4267-1-kgroeneveld@lenbrook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZwu6fw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yly6QCfdXwmKEqG4H7xonERzmEkP9/sYtoAnAsafKV5
5pWgy7Jw+WH1s1L7IzGy
=xrG1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
net/9p/usbg: Fix build error
USB: yurex: kill needless initialization in yurex_read
Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
usb: xhci: Fix problem with xhci resume from suspend
usb: misc: onboard_usb_dev: introduce new config symbol for usb5744 SMBus support
usb: dwc3: core: Stop processing of pending events if controller is halted
usb: dwc3: re-enable runtime PM after failed resume
usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
usb: gadget: core: force synchronous registration
Registering a gadget driver is expected to complete synchronously and
immediately after calling driver_register() this function checks that
the driver has bound so as to return an error.
Set PROBE_FORCE_SYNCHRONOUS to ensure this is the case even when
asynchronous probing is set as the default.
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Cc: stable@vger.kernel.org
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20240913102325.2826261-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCI vendor ID for Cadence is defined in pci_ids.h. Use it.
While at it, move to PCI_DEVICE() macro and usual pattern for
PCI class and device IDs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240913132125.3630860-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here as well, and this also resolves the merge
conflict in:
drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We move the func_utils.h header to include/linux/usb to be
able to compile function drivers outside of the
drivers/usb/gadget/function directory.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240116-ml-topic-u9p-v12-1-9a27de5160e0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace kthread_create/wake_up_process() with kthread_run()
to simplify the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://lore.kernel.org/r/20240903014249.3098082-1-lihongbo22@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bInterfaceProtocol is hardcoded to USB_CDC_ACM_PROTO_AT_V25TER. This
will lead to problems with ModemManger which will gladly try to probe
that port as a modem if the gadget also has a network function.
ModemManager will try to send AT commands to the ACM port. Make the
bInterfaceProtocol configurable. For this, track the number of instances
and only allow write to the property if there are no intances (yet).
This will also set bFunctionProtocol to the same value, see commit
5c8db070b4 ("USB: Change acm_iad_descriptor bFunctionProtocol to
USB_CDC_ACM_PROTO_AT_V25TER") for more details.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20240825180446.3757073-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit "6acba0345b usb:gadget:uvc Do not use worker thread to pump
isoc usb requests", pump work could only be queued in uvc_video_complete()
and uvc_v4l2_qbuf(). If VIDIOC_QBUF is executed before VIDIOC_STREAMON,
we can only depend on uvc_video_complete() to queue pump work. However,
this requires some free requests in req_ready list. If req_ready list is
empty all the time, pump work will never be queued and video datas will
never be pumped to usb controller. Actually, this situation could happen
when run uvc-gadget with static image:
$ ./uvc-gadget -i 1080p.jpg uvc.0
When capture image from this device, the user app will always block there.
The issue is uvc driver has queued video buffer before streamon, but the
req_ready list is empty all the time after streamon. This will queue pump
work in uvcg_video_enable() to fill some request to req_ready list so the
uvc device could work properly.
Fixes: 6acba0345b ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240814112537.2608949-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While supporting GET_REPORT is a mandatory request per the HID
specification the current implementation of the GET_REPORT request responds
to the USB Host with an empty reply of the request length. However, some
USB Hosts will request the contents of feature reports via the GET_REPORT
request. In addition, some proprietary HID 'protocols' will expect
different data, for the same report ID, to be to become available in the
feature report by sending a preceding SET_REPORT to the USB Device that
defines what data is to be presented when that feature report is
subsequently retrieved via GET_REPORT (with a very fast < 5ms turn around
between the SET_REPORT and the GET_REPORT).
There are two other patch sets already submitted for adding GET_REPORT
support. The first [1] allows for pre-priming a list of reports via IOCTLs
which then allows the USB Host to perform the request, with no further
userspace interaction possible during the GET_REPORT request. And another
[2] which allows for a single report to be setup by userspace via IOCTL,
which will be fetched and returned by the kernel for subsequent GET_REPORT
requests by the USB Host, also with no further userspace interaction
possible.
This patch, while loosely based on both the patch sets, differs by allowing
the option for userspace to respond to each GET_REPORT request by setting
up a poll to notify userspace that a new GET_REPORT request has arrived. To
support this, two extra IOCTLs are supplied. The first of which is used to
retrieve the report ID of the GET_REPORT request (in the case of having
non-zero report IDs in the HID descriptor). The second IOCTL allows for
storing report responses in a list for responding to requests.
The report responses are stored in a list (it will be either added if it
does not exist or updated if it exists already). A flag (userspace_req) can
be set to whether subsequent requests notify userspace or not.
Basic operation when a GET_REPORT request arrives from USB Host:
- If the report ID exists in the list and it is set for immediate return
(i.e. userspace_req == false) then response is sent immediately,
userspace is not notified
- The report ID does not exist, or exists but is set to notify userspace
(i.e. userspace_req == true) then notify userspace via poll:
- If userspace responds, and either adds or update the response in
the list and respond to the host with the contents
- If userspace does not respond within the fixed timeout (2500ms)
but the report has been set prevously, then send 'old' report
contents
- If userspace does not respond within the fixed timeout (2500ms)
and the report does not exist in the list then send an empty
report
Note that userspace could 'prime' the report list at any other time.
While this patch allows for flexibility in how the system responds to
requests, and therefore the HID 'protocols' that could be supported, a
drawback is the time it takes to service the requests and therefore the
maximum throughput that would be achievable. The USB HID Specification
v1.11 itself states that GET_REPORT is not intended for periodic data
polling, so this limitation is not severe.
Testing on an iMX8M Nano Ultra Lite with a heavy multi-core CPU loading
showed that userspace can typically respond to the GET_REPORT request
within 1200ms - which is well within the 5000ms most operating systems seem
to allow, and within the 2500ms set by this patch.
[1] https://lore.kernel.org/all/20220805070507.123151-2-sunil@amarulasolutions.com/
[2] https://lore.kernel.org/all/20220726005824.2817646-1-vi@endrift.com/
Signed-off-by: David Sands <david.sands@biamp.com>
Signed-off-by: Chris Wulff <chris.wulff@biamp.com>
Link: https://lore.kernel.org/r/20240817142850.1311460-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential dereferencing of ERR_PTR() in find_format_by_pix()
and uvc_v4l2_enum_format().
Fix the following smatch errors:
drivers/usb/gadget/function/uvc_v4l2.c:124 find_format_by_pix()
error: 'fmtdesc' dereferencing possible ERR_PTR()
drivers/usb/gadget/function/uvc_v4l2.c:392 uvc_v4l2_enum_format()
error: 'fmtdesc' dereferencing possible ERR_PTR()
Also, fix similar issue in uvc_v4l2_try_format() for potential
dereferencing of ERR_PTR().
Signed-off-by: Abhishek Tamboli <abhishektamboli9@gmail.com>
Link: https://lore.kernel.org/r/20240815102202.594812-1-abhishektamboli9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240814030443.3876203-1-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
list_entry() will never return a NULL pointer, thus remove the
check.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/20240821085245.25348-1-liyuesong@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the ability for the USB FunctionFS (FFS) gadget driver to be able
to create Device Firmware Upgrade (DFU) functional descriptors. [1]
This patch allows implementation of DFU in userspace using the
FFS gadget. The DFU protocol uses the control pipe (ep0) for all
messaging so only the addition of the DFU functional descriptor
is needed in the kernel driver.
The DFU functional descriptor is written to the ep0 file along with
any other descriptors during FFS setup. DFU requires an interface
descriptor followed by the DFU functional descriptor.
This patch includes documentation of the added descriptor for DFU
and conversion of some existing documentation to kernel-doc format
so that it can be included in the generated docs.
An implementation of DFU 1.1 that implements just the runtime descriptor
using the FunctionFS gadget (with rebooting into u-boot for DFU mode)
has been tested on an i.MX8 Nano.
An implementation of DFU 1.1 that implements both runtime and DFU mode
using the FunctionFS gadget has been tested on Xilinx Zynq UltraScale+.
Note that for the best performance of firmware update file transfers, the
userspace program should respond as quick as possible to the setup packets.
[1] https://www.usb.org/sites/default/files/DFU_1.1.pdf
Signed-off-by: David Sands <david.sands@biamp.com>
Co-developed-by: Chris Wulff <crwulff@gmail.com>
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240811000004.1395888-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct config_item_type' is not modified in this file.
Apparently, these structures are only used with
config_group_init_type_name() which takes a const struct config_item_type*
as a 3rd argument.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
40834 5112 64 46010 b3ba drivers/usb/gadget/configfs.o
After:
=====
text data bss dec hex filename
41218 4728 64 46010 b3ba drivers/usb/gadget/configfs.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/513223e97082e1bb758e36d55c175ec9ea34a71c.1723323896.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"linux/usb/gadget_configfs.h" is only included in
"drivers/usb/gadget/configfs.c", so there is no need to declare a function
in the header file. it is only used in this .c file.
It's better to have it static.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/958cb49dca1bff4254a3492c018efbf3b01918b4.1723323107.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert array initializers to C99 syntax by adding the '=' after
each designated initializer.
Fix the following smatch warnings:
drivers/usb/gadget/function/u_audio.c:1117:20:
warning: obsolete array initializer, use C99 syntax
drivers/usb/gadget/function/u_audio.c:1124:28:
warning: obsolete array initializer, use C99 syntax
drivers/usb/gadget/function/u_audio.c:1131:19:
warning: obsolete array initializer, use C99 syntax
drivers/usb/gadget/function/u_audio.c:1138:27:
warning: obsolete array initializer, use C99 syntax
drivers/usb/gadget/function/u_audio.c:1145:25:
warning: obsolete array initializer, use C99 syntax
Also, fix two checkpatch.pl warnings:
WARNING: please, no spaces at the start of a line
+ [UAC_FBACK_CTRL] = {$
WARNING: please, no spaces at the start of a line
+ [UAC_MUTE_CTRL] = {$
Signed-off-by: Abhishek Tamboli <abhishektamboli9@gmail.com>
Reviewed-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240801190209.500373-1-abhishektamboli9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ``alt`` parameter was used as a way to differentiate between
f->disable() and f->set_alt(). As the code paths diverge quite a bit,
pull out the f->disable() code from ffs_func_set_alt(), everything will
become clearer and less error prone. No change in functionality
intended.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240802140428.2000312-3-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The blamed commit made ffs_func_disable() always return -EINVAL as the
method calls ffs_func_set_alt() with the ``alt`` argument being
``(unsigned)-1``, which is always greater than MAX_ALT_SETTINGS.
Use the MAX_ALT_SETTINGS check just in the f->set_alt() code path,
f->disable() doesn't care about the ``alt`` parameter.
Make a surgical fix, but really the f->disable() code shall be pulled
out from ffs_func_set_alt(), the code will become clearer. A patch will
follow.
Note that ffs_func_disable() always returning -EINVAL made pixel6 crash
on USB disconnect.
Fixes: 2f550553e2 ("usb: gadget: f_fs: Add the missing get_alt callback")
Cc: stable <stable@kernel.org>
Reported-by: William McVicker <willmcvicker@google.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240802140428.2000312-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add icount support for the transmitting and receiving characters. This
will make the tty LED trigger work with the ttyGS devices.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20240730193840.2580358-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit aba3a8d01d ("usb: gadget: u_serial: add suspend
resume callbacks") added started_delayed flag, so that new ports
which are opened after USB suspend can start IO while resuming.
But if the port was already opened, and gadget suspend kicks in
afterwards, start_delayed will never be set. This causes resume
to bail out before calling gs_start_io(). Fix this by setting
start_delayed during suspend.
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240730125754.576326-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the descriptor has been set before looking at maxpacket.
This fixes a null pointer panic in this case.
This may happen if the gadget doesn't properly set up the endpoint
for the current speed, or the gadget descriptors are malformed and
the descriptor for the speed/endpoint are not found.
No current gadget driver is known to have this problem, but this
may cause a hard-to-find bug during development of new gadgets.
Fixes: 54f83b8c8e ("USB: gadget: Reject endpoints with 0 maxpacket value")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240725010419.314430-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions can fail if descriptors are malformed, or missing,
for the selected USB speed.
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Fixes: 24f779dac8 ("usb: gadget: f_uac2/u_audio: add feedback endpoint support")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240721192314.3532697-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the block number 0xff is given to Function Block Discovery
message, the device should return the information of all Function
Blocks, but currently the gadget driver treats it as an error.
Implement the proper behavior for the block 0xff instead.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240717095102.10493-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases to
get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions. It's not all that useful for a "write a whole driver
in rust" type of thing, but the firmware bindings do help out the
phy rust drivers, and the driver core bindings give a solid base on
which others can start their work. There is still a long way to go
here before we have a multitude of rust drivers being added, but
it's a great first step.
- driver core const api changes. This reached across all bus types,
and there are some fix-ups for some not-common bus types that
linux-next and 0-day testing shook out. This work is being done to
help make the rust bindings more safe, as well as the C code, moving
toward the end-goal of allowing us to put driver structures into
read-only memory. We aren't there yet, but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZqH+aQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoOQCfVBdLcBjEDAGh3L8qHRGMPy4rV2EAoL/r+zKm
cJEYtJpGtWX6aAtugm9E
=ZyJV
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
-----BEGIN PGP SIGNATURE-----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=vw2i
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Define PCIE_RESET_CONFIG_DEVICE_WAIT_MS for the generic 100ms
required after reset before config access (Kevin Xie)
- Define PCIE_T_RRS_READY_MS for the generic 100ms required after
reset before config access (probably should be unified with
PCIE_RESET_CONFIG_DEVICE_WAIT_MS) (Damien Le Moal)
Resource management:
- Rename find_resource() to find_resource_space() to be more
descriptive (Ilpo Järvinen)
- Export find_resource_space() for use by PCI core, which needs to
learn whether there is available space for a bridge window (Ilpo
Järvinen)
- Prevent double counting of resources so window size doesn't grow on
each remove/rescan cycle (Ilpo Järvinen)
- Relax bridge window sizing algorithm so a device doesn't break
simply because it was removed and rescanned (Ilpo Järvinen)
- Evaluate the ACPI PRESERVE_BOOT_CONFIG _DSM in
pci_register_host_bridge() (not acpi_pci_root_create()) so we can
unify it with similar DT functionality (Vidya Sagar)
- Extend use of DT "linux,pci-probe-only" property so it works
per-host bridge as well as globally (Vidya Sagar)
- Unify support for ACPI PRESERVE_BOOT_CONFIG _DSM and the DT
"linux,pci-probe-only" property in pci_preserve_config() (Vidya
Sagar)
Driver binding:
- Add devres infrastructure for managed request and map of partial
BAR resources (Philipp Stanner)
- Deprecate pcim_iomap_table() because uses like
"pcim_iomap_table()[0]" have no good way to return errors (Philipp
Stanner)
- Add an always-managed pcim_request_region() for use instead of
pci_request_region() and similar, which are sometimes managed
depending on whether pcim_enable_device() has been called
previously (Philipp Stanner)
- Reimplement pcim_set_mwi() so it doesn't need to keep store MWI
state (Philipp Stanner)
- Add pcim_intx() for use instead of pci_intx(), which is sometimes
managed depending on whether pcim_enable_device() has been called
previously (Philipp Stanner)
- Add managed pcim_iomap_range() to allow mapping of a partial BAR
(Philipp Stanner)
- Fix a devres mapping leak in drm/vboxvideo (Philipp Stanner)
Error handling:
- Add missing bridge locking in device reset path and add a warning
for other possible lock issues (Dan Williams)
- Fix use-after-free on concurrent DPC and hot-removal (Lukas Wunner)
Power management:
- Disable AER and DPC during suspend to avoid spurious wakeups if
they share an interrupt with PME (Kai-Heng Feng)
PCIe native device hotplug:
- Detect if a device was removed or replaced during system sleep so
we don't assume a new device is the one that used to be there
(Lukas Wunner)
Virtualization:
- Add an ACS quirk for Broadcom BCM5760X multi-function NIC; it
prevents transactions between functions even though it doesn't
advertise ACS, so the functions can be attached individually via
VFIO (Ajit Khaparde)
Peer-to-peer DMA:
- Add a "pci=config_acs=" kernel command-line parameter to relax
default ACS settings to enable additional peer-to-peer
configurations. Requires expert knowledge of topology and ACS
operation (Vidya Sagar)
Endpoint framework:
- Remove unused struct pci_epf_group.type_group (Christophe JAILLET)
- Fix error handling in vpci_scan_bus() and epf_ntb_epc_cleanup()
(Dan Carpenter)
- Make struct pci_epc_class constant (Greg Kroah-Hartman)
- Remove unused pci_endpoint_test_bar_{readl,writel} functions
(Jiapeng Chong)
- Rename "BME" to "Bus Master Enable" (Manivannan Sadhasivam)
- Rename struct pci_epc_event_ops.core_init() callback to epc_init()
(Manivannan Sadhasivam)
- Move DMA init to MHI .epc_init() callback for uniformity
(Manivannan Sadhasivam)
- Cancel EPF test delayed work when link goes down (Manivannan
Sadhasivam)
- Add struct pci_epc_event_ops.epc_deinit() callback for cleanup
needed on fundamental reset (Manivannan Sadhasivam)
- Add 64KB alignment to endpoint test to support Rockchip rk3588
(Niklas Cassel)
- Optimize endpoint test by using memcpy() instead of readl() (Niklas
Cassel)
Device tree bindings:
- Add generic "ats-supported" property to advertise that a PCIe Root
Complex supports ATS (Jean-Philippe Brucker)
Amazon Annapurna Labs PCIe controller driver:
- Validate IORESOURCE_BUS presence to avoid NULL pointer dereference
(Aleksandr Mishin)
Axis ARTPEC-6 PCIe controller driver:
- Rename .cpu_addr_fixup() parameter to reflect that it is a PCI
address, not a CPU address (Niklas Cassel)
Freescale i.MX6 PCIe controller driver:
- Convert to agnostic GPIO API (Andy Shevchenko)
Freescale Layerscape PCIe controller driver:
- Make struct mobiveil_rp_ops constant (Christophe JAILLET)
- Use new generic dw_pcie_ep_linkdown() to handle link-down events
(Manivannan Sadhasivam)
HiSilicon Kirin PCIe controller driver:
- Convert to agnostic GPIO API (Andy Shevchenko)
- Use _scoped() iterator for OF children to ensure refcounts are
decremented at loop exit (Javier Carrasco)
Intel VMD host bridge driver:
- Create sysfs "domain" symlink before downstream devices are exposed
to userspace by pci_bus_add_devices() (Jiwei Sun)
Loongson PCIe controller driver:
- Enable MSI when LS7A is used with new CPUs that have integrated
PCIe Root Complex, e.g., Loongson-3C6000, so downstream devices can
use MSI (Huacai Chen)
Microchip AXI PolarFlare PCIe controller driver:
- Move pcie-microchip-host.c to a new PLDA directory (Minda Chen)
- Factor PLDA generic items out to a common
plda,xpressrich3-axi-common.yaml binding (Minda Chen)
- Factor PLDA generic data structures and code out to shared
pcie-plda.h, pcie-plda-host.c (Minda Chen)
- Add PLDA generic interrupt handling with a .request_event_irq()
callback for vendor-specific events (Minda Chen)
- Add PLDA generic host init/deinit and map bus functions for use by
vendor-specific drivers (Minda Chen)
- Rework to use PLDA core (Minda Chen)
Microsoft Hyper-V host bridge driver:
- Return zero, not garbage, when reading PCI_INTERRUPT_PIN (Wei Liu)
NVIDIA Tegra194 PCIe controller driver:
- Remove unused struct tegra_pcie_soc (Dr. David Alan Gilbert)
- Set 64KB inbound ATU alignment restriction (Jon Hunter)
Qualcomm PCIe controller driver:
- Make the MHI reg region mandatory for X1E80100, since all PCIe
controllers have it (Abel Vesa)
- Prevent use of uninitialized data and possible error pointer
dereference (Dan Carpenter)
- Return error, not success, if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Add Operating Performance Points (OPP) support to scale performance
state based on aggregate link bandwidth to improve SoC power
efficiency (Krishna chaitanya chundru)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays
active even if other drivers don't vote for it (Krishna chaitanya
chundru)
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay
Sarkar)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory
corruption (Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if
the link is already disabled (Manivannan Sadhasivam)
- Use new generic dw_pcie_ep_linkdown() to handle link-down events
(Manivannan Sadhasivam)
- Add DT and endpoint driver support for the SA8775P SoC (Mrinmay
Sarkar)
- Add Hyper DMA (HDMA) support for the SA8775P SoC and enable it in
the EPF MHI driver (Mrinmay Sarkar)
- Set PCIE_PARF_NO_SNOOP_OVERIDE to override the default NO_SNOOP
attribute on the SA8775P SoC (both Root Complex and Endpoint mode)
to avoid possible memory corruption (Mrinmay Sarkar)
Renesas R-Car PCIe controller driver:
- Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup() to
avoid unnecessary backtrace (Marek Vasut)
- Add DT and driver support for R-Car V4H (R8A779G0) host and
endpoint. This requires separate proprietary firmware (Yoshihiro
Shimoda)
Rockchip PCIe controller driver:
- Assert PERST# for 100ms after power is stable (Damien Le Moal)
- Wait PCIE_T_RRS_READY_MS (100ms) after reset before starting
configuration (Damien Le Moal)
- Use GPIOD_OUT_LOW flag while requesting ep_gpio to fix a firmware
crash on Qcom-based modems with Rockpro64 board (Manivannan
Sadhasivam)
Rockchip DesignWare PCIe controller driver:
- Factor common parts of rockchip-dw-pcie DT binding to be shared by
Root Complex and Endpoint mode (Niklas Cassel)
- Add missing INTx signals to common DT binding (Niklas Cassel)
- Add eDMA items to DT binding for Endpoint controller (Niklas
Cassel)
- Fix initial dw-rockchip PERST# GPIO value to prevent unnecessary
short assert/deassert that causes issues with some WLAN controllers
(Niklas Cassel)
- Refactor dw-rockchip and add support for Endpoint mode (Niklas
Cassel)
- Call pci_epc_init_notify() and drop dw_pcie_ep_init_notify()
wrapper (Niklas Cassel)
- Add error messages in .probe() error paths to improve user
experience (Uwe Kleine-König)
Samsung Exynos PCIe controller driver:
- Use bulk clock APIs to simplify clock setup (Shradha Todi)
StarFive PCIe controller driver:
- Add DT binding and driver support for the StarFive JH7110
PLDA-based PCIe controller (Minda Chen)
Synopsys DesignWare PCIe controller driver:
- Add generic support for sending PME_Turn_Off when system suspends
(Frank Li)
- Fix incorrect interpretation of iATU slot 0 after PERST#
assert/deassert (Frank Li)
- Use msleep() instead of usleep_range() while waiting for link
(Konrad Dybcio)
- Refactor dw_pcie_edma_find_chip() to enable adding support for
Hyper DMA (HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't
auto detect this (Manivannan Sadhasivam)
- Call pci_epc_init_notify() and drop dw_pcie_ep_init_notify()
wrapper (Manivannan Sadhasivam)
- Pass the eDMA mapping format directly from drivers instead of
maintaining a capability for it (Manivannan Sadhasivam)
- Add generic dw_pcie_ep_linkdown() to notify EPF drivers about
link-down events and restore non-sticky DWC registers lost on link
down (Manivannan Sadhasivam)
- Add vendor-specific "apb" reg name, interrupt names, INTx names to
generic binding (Niklas Cassel)
- Enforce DWC restriction that 64-bit BARs must start with an
even-numbered BAR (Niklas Cassel)
- Consolidate args of dw_pcie_prog_outbound_atu() into a structure
(Yoshihiro Shimoda)
- Add support for endpoints to send Message TLPs, e.g., for INTx
emulation (Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Rename .cpu_addr_fixup() parameter to reflect that it is a PCI
address, not a CPU address (Niklas Cassel)
TI Keystone PCIe controller driver:
- Validate IORESOURCE_BUS presence to avoid NULL pointer dereference
(Aleksandr Mishin)
- Work around AM65x/DRA80xM Errata #i2037 that corrupts TLPs and
causes processor hangs by limiting Max_Read_Request_Size (MRRS) and
Max_Payload_Size (MPS) (Kishon Vijay Abraham I)
- Leave BAR 0 disabled for AM654x to fix a regression caused by
6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), which caused a 45-second boot delay (Siddharth
Vadapalli)
Xilinx Versal CPM PCIe controller driver:
- Fix overlapping bridge registers and 32-bit BAR addresses in DT
binding (Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Make struct switchtec_class constant (Greg Kroah-Hartman)
Miscellaneous:
- Remove unused struct acpi_handle_node (Dr. David Alan Gilbert)
- Add missing MODULE_DESCRIPTION() macros (Jeff Johnson)"
* tag 'pci-v6.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (154 commits)
PCI: loongson: Enable MSI in LS7A Root Complex
PCI: Extend ACS configurability
PCI: Add missing bridge lock to pci_bus_lock()
drm/vboxvideo: fix mapping leaks
PCI: Add managed pcim_iomap_range()
PCI: Remove legacy pcim_release()
PCI: Add managed pcim_intx()
PCI: vmd: Create domain symlink before pci_bus_add_devices()
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: Give pcim_set_mwi() its own devres cleanup callback
PCI: Move struct pci_devres.pinned bit to struct pci_dev
PCI: Remove struct pci_devres.enabled status bit
PCI: Document hybrid devres hazards
PCI: Add managed pcim_request_region()
PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()
PCI: Add managed partial-BAR request and map infrastructure
PCI: Add devres helpers for iomap table
PCI: Add and use devres helper for bit masks
...
