[ Upstream commit 9cecad134d ]
The code does not add IBI rules for devices with controller capability.
However, the secondary controller has the controller capability and works
at target mode when the device is probed. Therefore, add IBI rules for
such devices.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-2-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30bb1ce712 ]
Add a glue code for the MIPI I3C HCI on PCI bus with Intel Panther Lake
I3C controller PCI IDs.
MIPI I3C HCI on Intel platforms has additional logic around the MIPI I3C
HCI core logic. Those together create so called I3C slice on PCI bus.
Intel specific initialization code does a reset cycle to the I3C slice
before probing the MIPI I3C HCI part.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20241231115904.620052-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccdb2e0e3b ]
MIPI I3C HCI on Intel hardware requires a quirk where ring needs to stop
and set to run again after resuming the halted controller. This is not
expected from the MIPI I3C HCI specification and is Intel specific.
Add this quirk to generic aborted transfer handling and execute it only
when ring is not in running state after a transfer error and attempted
controller resume. This is the case on Intel hardware.
It is not fully clear to me what is the ring running state in generic
hardware in such case. I would expect if ring is not running, then stop
request is a no-op and run request is either required or does the same
what controller resume would do.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20241231115904.620052-1-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b266e0d4da upstream.
Fix a probe failure in the i3c master driver that occurs when no i3c
devices are connected to the bus.
The issue arises in `i3c_master_bus_init()` where the `ret` value is not
updated after calling `master->ops->set_speed()`. If no devices are
present, `ret` remains set to `I3C_ERROR_M2`, causing the code to
incorrectly proceed to `err_bus_cleanup`.
Cc: stable@vger.kernel.org
Fixes: aef79e189b ("i3c: master: support to adjust first broadcast address speed")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250108225533.915334-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b75439c945 ]
In dw_i3c_common_probe, &master->hj_work is bound with
dw_i3c_hj_work. And dw_i3c_master_irq_handler can call
dw_i3c_master_irq_handle_ibis function to start the work.
If we remove the module which will call dw_i3c_common_remove to
make cleanup, it will free master->base through i3c_master_unregister
while the work mentioned above will be used. The sequence of operations
that may lead to a UAF bug is as follows:
CPU0 CPU1
| dw_i3c_hj_work
dw_i3c_common_remove |
i3c_master_unregister(&master->base) |
device_unregister(&master->dev) |
device_release |
//free master->base |
| i3c_master_do_daa(&master->base)
| //use master->base
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in dw_i3c_common_remove.
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/bfc49c9527be5b513e7ceafeba314ca40a5be4bc.1732703537.git.xiaopei01@kylinos.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ca2738174 ]
Bus cleanup path in DMA mode may trigger a RING_OP_STAT interrupt when
the ring is being stopped. Depending on timing between ring stop request
completion, interrupt handler removal and code execution this may lead
to a NULL pointer dereference in hci_dma_irq_handler() if it gets to run
after the io_data pointer is set to NULL in hci_dma_cleanup().
Prevent this my masking the ring interrupts before ring stop request.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240920144432.62370-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 851bd21cdb ]
If the DTS contains 'assigned-address', a dynamic address leak occurs
during hotjoin events.
Assume a device have assigned-address 0xb.
- Device issue Hotjoin
- Call i3c_master_do_daa()
- Call driver xxx_do_daa()
- Call i3c_master_get_free_addr() to get dynamic address 0x9
- i3c_master_add_i3c_dev_locked(0x9)
- expected_dyn_addr = newdev->boardinfo->init_dyn_addr (0xb);
- i3c_master_reattach_i3c_dev(newdev(0xb), old_dyn_addr(0x9));
- if (dev->info.dyn_addr != old_dyn_addr &&
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 0xb != 0x9 -> TRUE
(!dev->boardinfo ||
^^^^^^^^^^^^^^^ -> FALSE
dev->info.dyn_addr != dev->boardinfo->init_dyn_addr)) {
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
0xb != 0xb -> FALSE
...
i3c_bus_set_addr_slot_status(&master->bus, old_dyn_addr,
I3C_ADDR_SLOT_FREE);
^^^
This will be skipped. So old_dyn_addr never free
}
- i3c_master_get_free_addr() will return increased sequence number.
Remove dev->info.dyn_addr != dev->boardinfo->init_dyn_addr condition check.
dev->info.dyn_addr should be checked before calling this function because
i3c_master_setnewda_locked() has already been called and the target device
has already accepted dyn_addr. It is too late to check if dyn_addr is free
in i3c_master_reattach_i3c_dev().
Add check to ensure expected_dyn_addr is free before
i3c_master_setnewda_locked().
Fixes: cc3a392d69 ("i3c: master: fix for SETDASA and DAA process")
Cc: stable@kernel.org
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-3-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f552fa280 ]
Extend the address status bit to 4 and introduce the
I3C_ADDR_SLOT_EXT_DESIRED macro to indicate that a device prefers a
specific address. This is generally set by the 'assigned-address' in the
device tree source (dts) file.
┌────┬─────────────┬───┬─────────┬───┐
│S/Sr│ 7'h7E RnW=0 │ACK│ ENTDAA │ T ├────┐
└────┴─────────────┴───┴─────────┴───┘ │
┌─────────────────────────────────────────┘
│ ┌──┬─────────────┬───┬─────────────────┬────────────────┬───┬─────────┐
└─►│Sr│7'h7E RnW=1 │ACK│48bit UID BCR DCR│Assign 7bit Addr│PAR│ ACK/NACK│
└──┴─────────────┴───┴─────────────────┴────────────────┴───┴─────────┘
Some master controllers (such as HCI) need to prepare the entire above
transaction before sending it out to the I3C bus. This means that a 7-bit
dynamic address needs to be allocated before knowing the target device's
UID information.
However, some I3C targets may request specific addresses (called as
"init_dyn_addr"), which is typically specified by the DT-'s
assigned-address property. Lower addresses having higher IBI priority. If
it is available, i3c_bus_get_free_addr() preferably return a free address
that is not in the list of desired addresses (called as "init_dyn_addr").
This allows the device with the "init_dyn_addr" to switch to its
"init_dyn_addr" when it hot-joins the I3C bus. Otherwise, if the
"init_dyn_addr" is already in use by another I3C device, the target device
will not be able to switch to its desired address.
If the previous step fails, fallback returning one of the remaining
unassigned address, regardless of its state in the desired list.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-2-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 851bd21cdb ("i3c: master: Fix dynamic address leak when 'assigned-address' is present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16aed0a652 ]
Replace the hardcoded value 2, which indicates 2 bits for I3C address
status, with the predefined macro I3C_ADDR_SLOT_STATUS_BITS.
Improve maintainability and extensibility of the code.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-1-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 851bd21cdb ("i3c: master: Fix dynamic address leak when 'assigned-address' is present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 25bc99be5f upstream.
Fix issue where disabling IBI on one device disables the entire IBI
interrupt. Modify bit 7:0 of enabled_events to serve as an IBI enable
counter, ensuring that the system IBI interrupt is disabled only when all
I3C devices have IBI disabled.
Cc: stable@kernel.org
Fixes: 7ff730ca45 ("i3c: master: svc: enable the interrupt in the enable ibi function")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241101165002.2479794-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b2ac810d8 upstream.
svc_i3c_master_do_daa() {
...
for (i = 0; i < dev_nb; i++) {
ret = i3c_master_add_i3c_dev_locked(m, addrs[i]);
if (ret)
goto rpm_out;
}
}
If two devices (A and B) are detected in DAA and address 0xa is assigned to
device A and 0xb to device B, a failure in i3c_master_add_i3c_dev_locked()
for device A (addr: 0xa) could prevent device B (addr: 0xb) from being
registered on the bus. The I3C stack might still consider 0xb a free
address. If a subsequent Hotjoin occurs, 0xb might be assigned to Device A,
causing both devices A and B to use the same address 0xb, violating the I3C
specification.
The return value for i3c_master_add_i3c_dev_locked() should not be checked
because subsequent steps will scan the entire I3C bus, independent of
whether i3c_master_add_i3c_dev_locked() returns success.
If device A registration fails, there is still a chance to register device
B. i3c_master_add_i3c_dev_locked() can reset DAA if a failure occurs while
retrieving device information.
Cc: stable@kernel.org
Fixes: 317bacf960 ("i3c: master: add enable(disable) hot join in sys entry")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241002-svc-i3c-hj-v6-6-7e6e1d3569ae@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18599e93e4 upstream.
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Cc: stable@vger.kernel.org # v5.17
Fixes: 05be23ef78 ("i3c: master: svc: add runtime pm support")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20240930091913.2545510-1-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36faa04ce3 ]
When a new device hotjoins, a new dynamic address is assigned.
i3c_master_add_i3c_dev_locked() identifies that the device was previously
attached to the bus and locates the olddev.
i3c_master_add_i3c_dev_locked()
{
...
olddev = i3c_master_search_i3c_dev_duplicate(newdev);
...
if (olddev) {
...
i3c_dev_disable_ibi_locked(olddev);
^^^^^^
The olddev should not receive any commands on the i3c bus as it
does not exist and has been assigned a new address. This will
result in NACK or timeout. So remove it.
}
i3c_dev_free_ibi_locked(olddev);
^^^^^^^^
This function internally calls i3c_dev_disable_ibi_locked() function
causing to send DISEC command with old Address.
The olddev should not receive any commands on the i3c bus as it
does not exist and has been assigned a new address. This will
result in NACK or timeout. So, update the olddev->ibi->enabled
flag to false to avoid DISEC with OldAddr.
}
Include part of Ravindra Yashvant Shinde's work:
https://lore.kernel.org/linux-i3c/20240820151917.3904956-1-ravindra.yashvant.shinde@nxp.com/T/#u
Fixes: 317bacf960 ("i3c: master: add enable(disable) hot join in sys entry")
Co-developed-by: Ravindra Yashvant Shinde <ravindra.yashvant.shinde@nxp.com>
Signed-off-by: Ravindra Yashvant Shinde <ravindra.yashvant.shinde@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241001162232.223724-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
In the svc_i3c_master_probe function, &master->hj_work is bound with
svc_i3c_master_hj_work, &master->ibi_work is bound with
svc_i3c_master_ibi_work. And svc_i3c_master_ibi_work can start the
hj_work, svc_i3c_master_irq_handler can start the ibi_work.
If we remove the module which will call svc_i3c_master_remove to
make cleanup, it will free master->base through i3c_master_unregister
while the work mentioned above will be used. The sequence of operations
that may lead to a UAF bug is as follows:
CPU0 CPU1
| svc_i3c_master_hj_work
svc_i3c_master_remove |
i3c_master_unregister(&master->base)|
device_unregister(&master->dev) |
device_release |
//free master->base |
| i3c_master_do_daa(&master->base)
| //use master->base
Fix it by ensuring that the work is canceled before proceeding with the
cleanup in svc_i3c_master_remove.
Fixes: 0f74f8b667 ("i3c: Make i3c_master_unregister() return void")
Cc: stable@vger.kernel.org
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/stable/20240914154030.180-1-kxwang23%40m.fudan.edu.cn
Link: https://lore.kernel.org/r/20240914163932.253-1-kxwang23@m.fudan.edu.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the cdns_i3c_master_probe function, &master->hj_work is bound with
cdns_i3c_master_hj. And cdns_i3c_master_interrupt can call
cnds_i3c_master_demux_ibis function to start the work.
If we remove the module which will call cdns_i3c_master_remove to
make cleanup, it will free master->base through i3c_master_unregister
while the work mentioned above will be used. The sequence of operations
that may lead to a UAF bug is as follows:
CPU0 CPU1
| cdns_i3c_master_hj
cdns_i3c_master_remove |
i3c_master_unregister(&master->base) |
device_unregister(&master->dev) |
device_release |
//free master->base |
| i3c_master_do_daa(&master->base)
| //use master->base
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in cdns_i3c_master_remove.
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Link: https://lore.kernel.org/r/20240911153544.848398-1-kxwang23@m.fudan.edu.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
According to I3C Specification(Version 1.1) 5.1.2.4 "Use of Clock
Speed to Prevent Legacy I2C Devices From Seeing I3C traffic", when
slow i2c devices(FM/FM+ rate i2c frequency without 50ns filter)
works on i3c bus, i3c SDR should work at FM/FM+ rate.
Adjust timing for difference mode.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240719080233.842771-1-carlos.song@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C controller should support adjusting open drain timing for the first
broadcast address to make I3C device working as a i2c device can see slow
broadcast address to close its Spike Filter to change working at i3c mode.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Link: https://lore.kernel.org/r/20240910051626.4052552-2-carlos.song@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
According to I3C spec 6.2 Timing Specification, the Open Drain High Period
of SCL Clock timing for first broadcast address should be adjusted to 200ns
at least. I3C device working as i2c device will see the broadcast to close
its Spike Filter then change to work at I3C mode. After that I3C open drain
SCL high level should be adjusted back.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240910051626.4052552-1-carlos.song@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Based on the I3C TCRI specification, the rules for determining the I3C
mode are as follows:
I3C SCL rate > 8MHz: use SDR0, as SDR1 has a maximum data rate of 8MHz
I3C SCL rate > 6MHz: use SDR1, as SDR2 has a maximum data rate of 6MHz
I3C SCL rate > 4MHz: use SDR2, as SDR3 has a maximum data rate of 4MHz
I3C SCL rate > 2MHz: use SDR3, as SDR4 has a maximum data rate of 2MHz
Otherwise, use SDR4
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20240826033821.175591-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://lore.kernel.org/r/20240826123957.379212-1-liaochen4@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current driver sets the response buffer threshold value to 1
(N+1, 2 DWORDS) in the QUEUE THRESHOLD register. However, the AMD
I3C controller only generates interrupts when the response buffer
threshold value is set to 0 (1 DWORD).
Therefore, a quirk is added to set the response buffer threshold value
to 0.
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Co-developed-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Signed-off-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Co-developed-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20240829091713.736217-7-Shyam-sundar.S-k@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The AMD HCI controller is currently unstable at 12.5 MHz. To address this,
a quirk is added to configure the clock rate to 9 MHz as a workaround,
with proportional adjustments to the Open-Drain (OD) and Push-Pull (PP)
values.
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Co-developed-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20240829091713.736217-6-Shyam-sundar.S-k@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The reg_* helper macros are currently limited to core.c. Moving them to
hci.h will allow their functionality to be utilized in other files outside
of core.c.
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Co-developed-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20240829091713.736217-5-Shyam-sundar.S-k@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The AMD HCI controller currently only supports PIO mode but exposes DMA
rings to the OS, which leads to the controller being configured in DMA
mode. To address this, add a quirk to avoid configuring the controller in
DMA mode and default to PIO mode.
Additionally, introduce a generic quirk infrastructure to the mipi-i3c-hci
driver to facilitate seamless future quirk additions.
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Co-developed-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Signed-off-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Co-developed-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20240829091713.736217-4-Shyam-sundar.S-k@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The HC_CONTROL_PIO_MODE bit was introduced in the HC_CONTROL register
starting from version 1.1. Therefore, checking the HC_CONTROL_PIO_MODE bit
on hardware that adheres to older specification revisions (i.e., versions
earlier than 1.1) is incorrect. To address this, add an additional check
to read the HCI version before attempting to read the HC_CONTROL_PIO_MODE
status.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240829091713.736217-3-Shyam-sundar.S-k@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current driver code lacks the necessary plumbing for ACPI IDs,
preventing the mipi-i3c-hci driver from being loaded on x86
platforms that advertise I3C ACPI support.
Add the AMDI5017 ACPI ID to the list of supported IDs.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240829091713.736217-2-Shyam-sundar.S-k@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Drivers:
- dw: optional apb clock and power management support, IBI handling fixes
- mipi-i3c-hci: IBI handling fixes
- svc: few fixes
-----BEGIN PGP SIGNATURE-----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=WFhg
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"This cycle, there are new features for the Designware controller and
fixes for the other IPs:
- dw: optional apb clock and power management support, IBI handling
fixes
- mipi-i3c-hci: IBI handling fixes
- svc: a few fixes"
* tag 'i3c/for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
dt-bindings: i3c: add header for generic I3C flags
i3c: master: svc: Fix error code in svc_i3c_master_do_daa_locked()
i3c: master: Enhance i3c_bus_type visibility for device searching & event monitoring
i3c: dw: Add power management support
i3c: dw: Add some functions for reusability
i3c: dw: Save timing registers and other values
i3c: master: svc: Improve DAA STOP handle code logic
i3c: dw: Add optional apb clock
i3c: dw: Use new *_enabled clk API
dt-bindings: i3c: dw: Add apb clock binding
i3c: master: svc: Convert comma to semicolon
i3c: mipi-i3c-hci: Round IBI data chunk size to HW supported value
i3c: mipi-i3c-hci: Error out instead on BUG_ON() in IBI DMA setup
i3c: mipi-i3c-hci: Set IBI Status and Data Ring base addresses
i3c: mipi-i3c-hci: Switch to lower_32_bits()/upper_32_bits() helpers
i3c: dw: Remove ibi_capable property
i3c: dw: Fix IBI intr programming
i3c: dw: Fix clearing queue thld
i3c: mipi-i3c-hci: Fix number of DAT/DCT entries for HCI versions < 1.1
i3c: master: svc: resend target address when get NACK
This code has a typo so it returns positive EIO instead of negative -EIO. Fix
it!
Fixes: a7809cb368b9 ("i3c: master: svc: Improve DAA STOP handle code logic")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/e017edfc-da64-496b-8516-958bec27cd9a@stanley.mountain
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Improve the visibility of i3c_bus_type to facilitate searching for
i3c devices attached to the i3c bus. Enable other drivers to use
bus_register_notifier to monitor i3c bus device events.
Signed-off-by: Bhoomik Gupta <bhoomik.gupta@nxp.com>
Link: https://lore.kernel.org/r/20240708053835.3003986-1-bhoomik.gupta@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for runtime and system power management.
Handle clocks, resets, pads as part of suspend and resume.
Restore controller registers that could be lost due to suspend.
Finally add get and put calls appropriately in functions which
access controller : bus_init, do_daa, send_ccc_cmd, priv_xfers,
i2c_xfers, ibi and hot-join.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240708062103.3296587-4-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Separate logic for setting intr/thld registers in a func.
Also modify enable function to take care of setting all fields in DEVICE_CTRL.
These functions can be reused later for power management.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240708062103.3296587-3-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add variables to store timing registers and other values.
These variables would be later used to restore registers
during resume without recomputation.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240708062103.3296587-2-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The REQUEST_PROC_DAA command behaves differently from other commands.
Sometimes the hardware can auto emit STOP, but in other conditions, it
cannot.
Improves the code logic to better handle these situations.
Hardware can auto emit STOP only when the following conditions are met:
- The previous I3C device correctly returns a PID and ACKs an I3C address.
- A NACK is received when emitting 7E to try to get the next I3C device's
PID.
In all other cases, a manual STOP emission is needed.
The code is changed to emit STOP when break the while loop and 'return 0'
only when the hardware can auto emit STOP.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240702223107.403057-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move to "enabled" variant of clk_get API. It takes care
of enable and disable calls during the probe and remove.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240628154603.326075-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The dma.c: hci_dma_init() sets the CHUNK_SIZE field in the IBI_SETUP
register incorrectly if the calculated ibi_chunk_sz is not exactly
2^(n+2) bytes, where n is 0..6.
Fix this by rounding the chunk size up to nearest 2^(n+2) bytes.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240628131559.502822-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Definitely condition dma_get_cache_alignment * defined value > 256
during driver initialization is not reason to BUG_ON(). Turn that to
graceful error out with -EINVAL.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240628131559.502822-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
IBI Status and Data Ring base address registers are not set so HW
obviously cannot update those rings after In-Band Interrupt.
Set them to already allocated and mapped ring addresses.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240628131559.502822-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Rather than having own lo32()/hi32() helpers for dealing with 32-bit and
64-bit build targets switch to generic lower_32_bits()/upper_32_bits()
helpers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240628131559.502822-1-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since DW I3C IP master role always supports IBI, we don't need
to keep two variants of master ops and select one using this
property. Hence remove the code.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240627034119.3938050-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
IBI_SIR_REQ_REJECT register is not present if the IP has
IC_HAS_IBI_DATA = 1 set. So don't rely on doing read-
modify-write op on this register.
Instead maintain a variable to store the sir reject mask
and use it to set IBI_SIR_REQ_REJECT.
Signed-off-by: Aniket <aniketmaurya@google.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I was wrong about the TABLE_SIZE field description in the
commit 0676bfebf5 ("i3c: mipi-i3c-hci: Fix DAT/DCT entry sizes").
For the MIPI I3C HCI versions 1.0 and earlier the TABLE_SIZE field in
the registers DAT_SECTION_OFFSET and DCT_SECTION_OFFSET is indeed defined
in DWORDs and not number of entries like it is defined in later versions.
Where above fix allowed driver initialization to continue the wrongly
interpreted TABLE_SIZE field leads variables DAT_entries being twice and
DCT_entries four times as big as they really are.
That in turn leads clearing the DAT table over the boundary in the
dat_v1.c: hci_dat_v1_init().
So interprete the TABLE_SIZE field in DWORDs for HCI versions < 1.1 and
fix number of DAT/DCT entries accordingly.
Fixes: 0676bfebf5 ("i3c: mipi-i3c-hci: Fix DAT/DCT entry sizes")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
According to I3C Spec 1.1.1, 11-Jun-2021, section: 5.1.2.2.3:
If the Controller chooses to start an I3C Message with an I3C Dynamic
Address, then special provisions shall be made because that same I3C Target
may be initiating an IBI or a Controller Role Request. So, one of three
things may happen: (skip 1, 2)
3. The Addresses match and the RnW bits also match, and so neither
Controller nor Target will ACK since both are expecting the other side to
provide ACK. As a result, each side might think it had "won" arbitration,
but neither side would continue, as each would subsequently see that the
other did not provide ACK.
...
For either value of RnW: Due to the NACK, the Controller shall defer the
Private Write or Private Read, and should typically transmit the Target
^^^^^^^^^^^^^^^^^^^
Address again after a Repeated START (i.e., the next one or any one prior
^^^^^^^^^^^^^
to a STOP in the Frame). Since the Address Header following a Repeated
START is not arbitrated, the Controller will always win (see Section
5.1.2.2.4).
Resend target address again if address is not 7E and controller get NACK.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add hot-join support for dw i3c master controller.
By default, the hot-join acknowledgment is disabled, and the hardware will
automatically send the DISEC CCC when it receives the hot-join request.
Users can use the sys entry to enable it.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20240429073624.256830-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Enable runtime PM for i3c master node during master registration time.
Sometimes i3c client device driver may want to control the PM of the
parent (master) to perform the transactions and save the power in an
efficient way by controlling the session. Hence device can call PM
APIs by passing the parent node.
Here, I3C target device when calls pm_runtime_get_sync(dev->parent)
couldn't invoke master drivers runtime PM callback registered by
the master driver because parent's PM status was disabled in the
Master node.
Also call pm_runtime_no_callbacks() and pm_suspend_ignore_children()
for the master node to not have any callback addition and ignore the
children to have runtime PM work just locally in the driver. This
should be generic and common change for all i3c devices and should
not have any other impact.
With these changes, I3C client device works and able to invoke
master driver registered runtime PM callbacks.
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20240228093407.4038399-1-quic_msavaliy@quicinc.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
