[ Upstream commit 55741c7233 ]
The ffs() function returns the index of the first set bit, starting from 1.
If no bits are set, it returns zero. This behavior causes an off-by-one
page size in the debug message, as the page size calculation [1]
is zero-based, while ffs() is one-based.
Fix this by subtracting one from the result of ffs(). Note that since
variable 'val' is unsigned, subtracting one from zero will result in the
maximum unsigned integer value. Consequently, the condition 'if (val < 16)'
will still function correctly.
[1], Page size: (2^(n+12)), where 'n' is the set page size bit.
Fixes: 81720ec532 ("usb: host: xhci: use ffs() in xhci_mem_init()")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bb0ba4cb10 upstream.
Two clearly different specimens of NEC uPD720200 (one with start/stop
bug, one without) were seen to cause IOMMU faults after some Missed
Service Errors. Faulting address is immediately after a transfer ring
segment and patched dynamic debug messages revealed that the MSE was
received when waiting for a TD near the end of that segment:
[ 1.041954] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ffa08fe0
[ 1.042120] xhci_hcd: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0005 address=0xffa09000 flags=0x0000]
[ 1.042146] xhci_hcd: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0005 address=0xffa09040 flags=0x0000]
It gets even funnier if the next page is a ring segment accessible to
the HC. Below, it reports MSE in segment at ff1e8000, plows through a
zero-filled page at ff1e9000 and starts reporting events for TRBs in
page at ff1ea000 every microframe, instead of jumping to seg ff1e6000.
[ 7.041671] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ff1e8fe0
[ 7.041999] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ff1e8fe0
[ 7.042011] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint
[ 7.042028] xhci_hcd: All TDs skipped for slot 1 ep 2. Clear skip flag.
[ 7.042134] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint
[ 7.042138] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 31
[ 7.042144] xhci_hcd: Looking for event-dma 00000000ff1ea040 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820
[ 7.042259] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint
[ 7.042262] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 31
[ 7.042266] xhci_hcd: Looking for event-dma 00000000ff1ea050 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820
At some point completion events change from Isoch Buffer Overrun to
Short Packet and the HC finally finds cycle bit mismatch in ff1ec000.
[ 7.098130] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 13
[ 7.098132] xhci_hcd: Looking for event-dma 00000000ff1ecc50 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820
[ 7.098254] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 13
[ 7.098256] xhci_hcd: Looking for event-dma 00000000ff1ecc60 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820
[ 7.098379] xhci_hcd: Overrun event on slot 1 ep 2
It's possible that data from the isochronous device were written to
random buffers of pending TDs on other endpoints (either IN or OUT),
other devices or even other HCs in the same IOMMU domain.
Lastly, an error from a different USB device on another HC. Was it
caused by the above? I don't know, but it may have been. The disk
was working without any other issues and generated PCIe traffic to
starve the NEC of upstream BW and trigger those MSEs. The two HCs
shared one x1 slot by means of a commercial "PCIe splitter" board.
[ 7.162604] usb 10-2: reset SuperSpeed USB device number 3 using xhci_hcd
[ 7.178990] sd 9:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x07 driverbyte=DRIVER_OK cmd_age=0s
[ 7.179001] sd 9:0:0:0: [sdb] tag#0 CDB: opcode=0x28 28 00 04 02 ae 00 00 02 00 00
[ 7.179004] I/O error, dev sdb, sector 67284480 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0
Fortunately, it appears that this ridiculous bug is avoided by setting
the chain bit of Link TRBs on isochronous rings. Other ancient HCs are
known which also expect the bit to be set and they ignore Link TRBs if
it's not. Reportedly, 0.95 spec guaranteed that the bit is set.
The bandwidth-starved NEC HC running a 32KB/uframe UVC endpoint reports
tens of MSEs per second and runs into the bug within seconds. Chaining
Link TRBs allows the same workload to run for many minutes, many times.
No negative side effects seen in UVC recording and UAC playback with a
few devices at full speed, high speed and SuperSpeed.
The problem doesn't reproduce on the newer Renesas uPD720201/uPD720202
and on old Etron EJ168 and VIA VL805 (but the VL805 has other bug).
[shorten line length of log snippets in commit messge -Mathias]
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58d0a3fab5 upstream.
Up until commit d56b0b2ab1 ("usb: xhci: ensure skipped isoc TDs are
returned when isoc ring is stopped") in v6.11, the driver didn't skip
missed isochronous TDs when handling Stoppend and Stopped - Length
Invalid events. Instead, it erroneously cleared the skip flag, which
would cause the ring to get stuck, as future events won't match the
missed TD which is never removed from the queue until it's cancelled.
This buggy logic seems to have been in place substantially unchanged
since the 3.x series over 10 years ago, which probably speaks first
and foremost about relative rarity of this case in normal usage, but
by the spec I see no reason why it shouldn't be possible.
After d56b0b2ab1, TDs are immediately skipped when handling those
Stopped events. This poses a potential problem in case of Stopped -
Length Invalid, which occurs either on completed TDs (likely already
given back) or Link and No-Op TRBs. Such event won't be recognized
as matching any TD (unless it's the rare Link TRB inside a TD) and
will result in skipping all pending TDs, giving them back possibly
before they are done, risking isoc data loss and maybe UAF by HW.
As a compromise, don't skip and don't clear the skip flag on this
kind of event. Then the next event will skip missed TDs. A downside
of not handling Stopped - Length Invalid on a Link inside a TD is
that if the TD is cancelled, its actual length will not be updated
to account for TRBs (silently) completed before the TD was stopped.
I had no luck producing this sequence of completion events so there
is no compelling demonstration of any resulting disaster. It may be
a very rare, obscure condition. The sole motivation for this patch
is that if such unlikely event does occur, I'd rather risk reporting
a cancelled partially done isoc frame as empty than gamble with UAF.
This will be fixed more properly by looking at Stopped event's TRB
pointer when making skipping decisions, but such rework is unlikely
to be backported to v6.12, which will stay around for a few years.
Fixes: d56b0b2ab1 ("usb: xhci: ensure skipped isoc TDs are returned when isoc ring is stopped")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c133ec0e57 upstream.
Raspberry Pi is a major user of those chips and they discovered a bug -
when the end of a transfer ring segment is reached, up to four TRBs can
be prefetched from the next page even if the segment ends with link TRB
and on page boundary (the chip claims to support standard 4KB pages).
It also appears that if the prefetched TRBs belong to a different ring
whose doorbell is later rung, they may be used without refreshing from
system RAM and the endpoint will stay idle if their cycle bit is stale.
Other users complain about IOMMU faults on x86 systems, unsurprisingly.
Deal with it by using existing quirk which allocates a dummy page after
each transfer ring segment. This was seen to resolve both problems. RPi
came up with a more efficient solution, shortening each segment by four
TRBs, but it complicated the driver and they ditched it for this quirk.
Also rename the quirk and add VL805 device ID macro.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://github.com/raspberrypi/linux/issues/4685
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215906
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250225095927.2512358-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 487cfd4a8e upstream.
When adding support for USB3-over-USB4 tunnelling detection, a check
for an Intel-specific capability was added. This capability, which
goes by ID 206, is used without any check that we are actually
dealing with an Intel host.
As it turns out, the Cadence XHCI controller *also* exposes an
extended capability numbered 206 (for unknown purposes), but of
course doesn't have the Intel-specific registers that the tunnelling
code is trying to access. Fun follows.
The core of the problems is that the tunnelling code blindly uses
vendor-specific capabilities without any check (the Intel-provided
documentation I have at hand indicates that 192-255 are indeed
vendor-specific).
Restrict the detection code to Intel HW for real, preventing any
further explosion on my (non-Intel) HW.
Cc: stable <stable@kernel.org>
Fixes: 948ce83fbb ("xhci: Add USB4 tunnel detection for USB3 devices on Intel hosts")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250227194529.2288718-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c81d9fcd5b upstream.
Some Renesas HCs require firmware upload to work, this is handled by the
xhci_pci_renesas driver. Other variants of those chips load firmware from
a SPI flash and are ready to work with xhci_pci alone.
A refactor merged in v6.12 broke the latter configuration so that users
are finding their hardware ignored by the normal driver and are forced to
enable the firmware loader which isn't really necessary on their systems.
Let xhci_pci work with those chips as before when the firmware loader is
disabled by kernel configuration.
Fixes: 25f51b76f9 ("xhci-pci: Make xhci-pci-renesas a proper modular driver")
Cc: stable <stable@kernel.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219616
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219726
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://lore.kernel.org/r/20250128104529.58a79bfc@foxbook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e0a19912a upstream.
If a command is queued to the final usable TRB of a ring segment, the
enqueue pointer is advanced to the subsequent link TRB and no further.
If the command is later aborted, when the abort completion is handled
the dequeue pointer is advanced to the first TRB of the next segment.
If no further commands are queued, xhci_handle_stopped_cmd_ring() sees
the ring pointers unequal and assumes that there is a pending command,
so it calls xhci_mod_cmd_timer() which crashes if cur_cmd was NULL.
Don't attempt timer setup if cur_cmd is NULL. The subsequent doorbell
ring likely is unnecessary too, but it's harmless. Leave it alone.
This is probably Bug 219532, but no confirmation has been received.
The issue has been independently reproduced and confirmed fixed using
a USB MCU programmed to NAK the Status stage of SET_ADDRESS forever.
Everything continued working normally after several prevented crashes.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219532
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e19852d0bf upstream.
The source of quirk XHCI_SKIP_PHY_INIT comes from xhci_plat_priv.quirks or
software node property. This will set skip_phy_initialization if software
node also has XHCI_SKIP_PHY_INIT property.
Fixes: a6cd2b3fa8 ("usb: host: xhci-plat: Parse xhci-missing_cas_quirk and apply quirk")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241209111423.4085548-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e21ebe51af upstream.
xHC hosts from several vendors have the same issue where endpoints start
so slowly that a later queued 'Stop Endpoint' command may complete before
endpoint is up and running.
The 'Stop Endpoint' command fails with context state error as the endpoint
still appears as stopped.
See commit 42b7581376 ("usb: xhci: Limit Stop Endpoint retries") for
details
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97264eaaba upstream.
If the clocks priv->iclk and priv->fclk were not enabled in ehci_hcd_sh_probe,
they should not be disabled in any path.
Conversely, if they was enabled in ehci_hcd_sh_probe, they must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 63c8455222 ("usb: ehci-hcd: Add support for SuperH EHCI.")
Cc: stable@vger.kernel.org # ff30bd6a66: sh: clk: Fix clk_enable() to return 0 on NULL clk
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241121114700.2100520-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d2ada0522 upstream.
If the current USB request was aborted, the spi thread would not respond
to any further requests. This is because the "curr_urb" pointer would
not become NULL, so no further requests would be taken off the queue.
The solution here is to set the "urb_done" flag, as this will cause the
correct handling of the URB. Also clear interrupts that should only be
expected if an URB is in progress.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20241124221430.1106080-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 474538b8dd upstream.
Stop Endpoint command on an already stopped endpoint fails and may be
misinterpreted as a known hardware bug by the completion handler. This
results in an unnecessary delay with repeated retries of the command.
Avoid queuing this command when endpoint state flags indicate that it's
stopped or halted and the command will fail. If commands are pending on
the endpoint, their completion handlers will process cancelled TDs so
it's done. In case of waiting for external operations like clearing TT
buffer, the endpoint is stopped and cancelled TDs can be processed now.
This eliminates practically all unnecessary retries because an endpoint
with pending URBs is maintained in Running state by the driver, unless
aforementioned commands or other operations are pending on it. This is
guaranteed by xhci_ring_ep_doorbell() and by the fact that it is called
every time any of those operations completes.
The only known exceptions are hardware bugs (the endpoint never starts
at all) and Stream Protocol errors not associated with any TRB, which
cause an endpoint reset not followed by restart. Sounds like a bug.
Generally, these retries are only expected to happen when the endpoint
fails to start for unknown/no reason, which is a worse problem itself,
and fixing the bug eliminates the retries too.
All cases were tested and found to work as expected. SET_DEQ_PENDING
was produced by patching uvcvideo to unlink URBs in 100us intervals,
which then runs into this case very often. EP_HALTED was produced by
restarting 'cat /dev/ttyUSB0' on a serial dongle with broken cable.
EP_CLEARING_TT by the same, with the dongle on an external hub.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-34-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 484c3bab2d upstream.
xhci_invalidate_cancelled_tds() may not work correctly if the hardware
is modifying endpoint or stream contexts at the same time by executing
a Set TR Dequeue command. And even if it worked, it would be unable to
queue Set TR Dequeue for the next stream, failing to clear xHC cache.
On stream endpoints, a chain of Set TR Dequeue commands may take some
time to execute and we may want to cancel more TDs during this time.
Currently this leads to Stop Endpoint completion handler calling this
function without testing for SET_DEQ_PENDING, which will trigger the
aforementioned problems when it happens.
On all endpoints, a halt condition causes Reset Endpoint to be queued
and an error status given to the class driver, which may unlink more
URBs in response. Stop Endpoint is queued and its handler may execute
concurrently with Set TR Dequeue queued by Reset Endpoint handler.
(Reset Endpoint handler calls this function too, but there seems to
be no possibility of it running concurrently with Set TR Dequeue).
Fix xhci_invalidate_cancelled_tds() to work correctly under a pending
Set TR Dequeue. Bail out of the function when SET_DEQ_PENDING is set,
then make the completion handler call the function again and also call
xhci_giveback_invalidated_tds(), which needs to be called next.
This seems to fix another potential bug, where the handler would call
xhci_invalidate_cancelled_tds(), which may clear some deferred TDs if
a sanity check fails, and the TDs wouldn't be given back promptly.
Said sanity check seems to be wrong and prone to false positives when
the endpoint halts, but fixing it is beyond the scope of this change,
besides ensuring that cleared TDs are given back properly.
Fixes: 5ceac4402f ("xhci: Handle TD clearing for multiple streams case")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-33-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42b7581376 upstream.
Some host controllers fail to atomically transition an endpoint to the
Running state on a doorbell ring and enter a hidden "Restarting" state,
which looks very much like Stopped, with the important difference that
it will spontaneously transition to Running anytime soon.
A Stop Endpoint command queued in the Restarting state typically fails
with Context State Error and the completion handler sees the Endpoint
Context State as either still Stopped or already Running. Even a case
of Halted was observed, when an error occurred right after the restart.
The Halted state is already recovered from by resetting the endpoint.
The Running state is handled by retrying Stop Endpoint.
The Stopped state was recognized as a problem on NEC controllers and
worked around also by retrying, because the endpoint soon restarts and
then stops for good. But there is a risk: the command may fail if the
endpoint is "stopped for good" already, and retries will fail forever.
The possibility of this was not realized at the time, but a number of
cases were discovered later and reproduced. Some proved difficult to
deal with, and it is outright impossible to predict if an endpoint may
fail to ever start at all due to a hardware bug. One such bug (albeit
on ASM3142, not on NEC) was found to be reliably triggered simply by
toggling an AX88179 NIC up/down in a tight loop for a few seconds.
An endless retries storm is quite nasty. Besides putting needless load
on the xHC and CPU, it causes URBs never to be given back, paralyzing
the device and connection/disconnection logic for the whole bus if the
device is unplugged. User processes waiting for URBs become unkillable,
drivers and kworker threads lock up and xhci_hcd cannot be reloaded.
For peace of mind, impose a timeout on Stop Endpoint retries in this
case. If they don't succeed in 100ms, consider the endpoint stopped
permanently for some reason and just give back the unlinked URBs. This
failure case is rare already and work is under way to make it rarer.
Start this work today by also handling one simple case of race with
Reset Endpoint, because it costs just two lines to implement.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-32-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76d98856b1 upstream.
Sometimes the hub driver does not recognize the USB device connected
to the external USB2.0 hub when the system resumes from S4.
After the SetPortFeature(PORT_RESET) request is completed, the hub
driver calls the HCD reset_device callback, which will issue a Reset
Device command and free all structures associated with endpoints
that were disabled.
This happens when the xHCI driver issue a Reset Device command to
inform the Etron xHCI host that the USB device associated with a
device slot has been reset. Seems that the Etron xHCI host can not
perform this command correctly, affecting the USB device.
To work around this, the xHCI driver should obtain a new device slot
with reference to commit 651aaf36a7 ("usb: xhci: Handle USB transaction
error on address command"), which is another way to inform the Etron
xHCI host that the USB device has been reset.
Add a new XHCI_ETRON_HOST quirk flag to invoke the workaround in
xhci_discover_or_reset_device().
Fixes: 2a8f82c4ce ("USB: xhci: Notify the xHC when a device is reset.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e735e957f2 upstream.
Since commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors"), unplugging USB device while enumeration results in
errors like this:
[ 364.855321] xhci_hcd 0000:0b:00.0: ERROR Transfer event for disabled endpoint slot 5 ep 2
[ 364.864622] xhci_hcd 0000:0b:00.0: @0000002167656d70 67f03000 00000021 0c000000 05038001
[ 374.934793] xhci_hcd 0000:0b:00.0: Abort failed to stop command ring: -110
[ 374.958793] xhci_hcd 0000:0b:00.0: xHCI host controller not responding, assume dead
[ 374.967590] xhci_hcd 0000:0b:00.0: HC died; cleaning up
[ 374.973984] xhci_hcd 0000:0b:00.0: Timeout while waiting for configure endpoint command
Seems that Etorn xHCI host can not perform Soft Retry correctly, apply
XHCI_NO_SOFT_RETRY quirk to disable Soft Retry and then issue is gone.
This patch depends on commit a4a251f8c2 ("usb: xhci: do not perform
Soft Retry for some xHCI hosts").
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7b11fe579 upstream.
Combine two if statements, because these hosts have the same
quirk flags applied.
[Mathias: has stable tag because other fixes in series depend on this]
Fixes: 91f7a1524a ("xhci: Apply broken streams quirk to Etron EJ188 xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e1c67abc9 upstream.
Performing a stability stress test on a USB3.0 2.5G ethernet adapter
results in errors like this:
[ 91.441469] r8152 2-3:1.0 eth3: get_registers -71
[ 91.458659] r8152 2-3:1.0 eth3: get_registers -71
[ 91.475911] r8152 2-3:1.0 eth3: get_registers -71
[ 91.493203] r8152 2-3:1.0 eth3: get_registers -71
[ 91.510421] r8152 2-3:1.0 eth3: get_registers -71
The r8152 driver will periodically issue lots of control-IN requests
to access the status of ethernet adapter hardware registers during
the test.
This happens when the xHCI driver enqueue a control TD (which cross
over the Link TRB between two ring segments, as shown) in the endpoint
zero's transfer ring. Seems the Etron xHCI host can not perform this
TD correctly, causing the USB transfer error occurred, maybe the upper
driver retry that control-IN request can solve problem, but not all
drivers do this.
| |
-------
| TRB | Setup Stage
-------
| TRB | Link
-------
-------
| TRB | Data Stage
-------
| TRB | Status Stage
-------
| |
To work around this, the xHCI driver should enqueue a No Op TRB if
next available TRB is the Link TRB in the ring segment, this can
prevent the Setup and Data Stage TRB to be breaked by the Link TRB.
Check if the XHCI_ETRON_HOST quirk flag is set before invoking the
workaround in xhci_queue_ctrl_tx().
Fixes: d0e96f5a71 ("USB: xhci: Control transfer support.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c9748267 upstream.
If the clock sehci->clk was not enabled in spear_ehci_hcd_drv_probe,
it should not be disabled in any path.
Conversely, if it was enabled in spear_ehci_hcd_drv_probe, it must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 7675d6ba43 ("USB: EHCI: make ehci-spear a separate driver")
Cc: stable@vger.kernel.org
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241114230310.432213-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the aborting of a command, the software receives a command
completion event for the command ring stopped, with the TRB pointing
to the next TRB after the aborted command.
If the command we abort is located just before the Link TRB in the
command ring, then during the 'command ring stopped' completion event,
the xHC gives the Link TRB in the event's cmd DMA, which causes a
mismatch in handling command completion event.
To address this situation, move the 'command ring stopped' completion
event check slightly earlier, since the specific command it stopped
on isn't of significant concern.
Fixes: 7f84eef0da ("USB: xhci: No-op command queueing and irq handler.")
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241022155631.1185-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pm_runtime_put in the remove function and pm_runtime_get to disable
RPM on platforms that don't support runtime D3, as re-enabling it through
sysfs auto power control may cause the controller to malfunction. This
can lead to issues such as hotplug devices not being detected due to
failed interrupt generation.
Fixes: a5d6264b63 ("xhci: Enable RPM on controllers that support low-power states")
Cc: stable <stable@kernel.org>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024133718.723846-1-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Treat each completed full size write to /dev/ttyDBC0 as a separate usb
transfer. Make sure the size of the TRBs matches the size of the tty
write by first queuing as many max packet size TRBs as possible up to
the last TRB which will be cut short to match the size of the tty write.
This solves an issue where userspace writes several transfers back to
back via /dev/ttyDBC0 into a kfifo before dbgtty can find available
request to turn that kfifo data into TRBs on the transfer ring.
The boundary between transfer was lost as xhci-dbgtty then turned
everyting in the kfifo into as many 'max packet size' TRBs as possible.
DbC would then send more data to the host than intended for that
transfer, causing host to issue a babble error.
Refuse to write more data to kfifo until previous tty write data is
turned into properly sized TRBs with data size boundaries matching tty
write size
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers fail to produce the final completion event on an
isochronous TD which experienced an error mid TD. We deal with it by
flagging such TDs and checking if the next event points at the flagged
TD or at the next one, and giving back the flagged TD if the latter.
This is not enough, because the next TD may be missed by the xHC. Or
there may be no next TD but a ring underrun. We also need to get such
TD quickly out of the way, or errors on later TDs may be handled wrong.
If the next TD experiences a Missed Service Error, we will set the skip
flag on the endpoint and then attempt skipping TDs when yet another
event arrives. In such scenario, we ought to report the 'error mid TD'
transfer as such rather than skip it.
Another problem case are Stopped events. If we see one after an error
mid TD, we naively assume that it's a Force Stopped Event because it
doesn't match the pending TD, but in reality it might be an ordinary
Stopped event for the next TD, which we fail to recognize and handle.
Fix this by moving error mid TD handling before the whole TD skipping
loop. Remove unnecessary conditions, always give back the TD if the new
event points to any TRB outside it or if the pointer is NULL, as may be
the case in Ring Underrun and Overrun events on 1st gen hardware. Only
if the pending TD isn't flagged, consider other actions like skipping.
As a side effect of reordering with skip and FSE cases, error mid TD is
reordered with last_td_was_short check. This is harmless, because the
two cases are mutually exclusive - only one can happen in any given run
of handle_tx_event().
Tested on the NEC host and a USB camera with flaky cable. Dynamic debug
confirmed that Transaction Errors are sometimes seen, sometimes mid-TD,
sometimes followed by Missed Service. In such cases, they were finished
properly before skipping began.
[Rebase on 6.12-rc1 -Mathias]
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid xHC host from processing a cancelled URB by always turning
cancelled URB TDs into no-op TRBs before queuing a 'Set TR Deq' command.
If the command fails then xHC will start processing the cancelled TD
instead of skipping it once endpoint is restarted, causing issues like
Babble error.
This is not a complete solution as a failed 'Set TR Deq' command does not
guarantee xHC TRB caches are cleared.
Fixes: 4db356924a ("xhci: turn cancelled td cleanup to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stream contex type (SCT) bitfield is used both in the stream context
data structure, and in the 'Set TR Dequeue pointer' command TRB.
In both cases it uses bits 3:1
The SCT_FOR_TRB(p) macro used to set the stream context type (SCT) field
for the 'Set TR Dequeue pointer' command TRB incorrectly shifts the value
1 bit left before masking the three bits.
Fix this by first masking and rshifting, just like the similar
SCT_FOR_CTX(p) macro does
This issue has not been visibile as the lost bit 3 is only used with
secondary stream arrays (SSA). Xhci driver currently only supports using
a primary stream array with Linear stream addressing.
Fixes: 95241dbdf8 ("xhci: Set SCT field for Set TR dequeue on streams")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If USB virtualizatoin is enabled, USB2 ports are shared between all
Virtual Functions. The USB2 port number owned by an USB2 root hub in
a Virtual Function may be less than total USB2 phy number supported
by the Tegra XUSB controller.
Using total USB2 phy number as port number to check all PORTSC values
would cause invalid memory access.
[ 116.923438] Unable to handle kernel paging request at virtual address 006c622f7665642f
...
[ 117.213640] Call trace:
[ 117.216783] tegra_xusb_enter_elpg+0x23c/0x658
[ 117.222021] tegra_xusb_runtime_suspend+0x40/0x68
[ 117.227260] pm_generic_runtime_suspend+0x30/0x50
[ 117.232847] __rpm_callback+0x84/0x3c0
[ 117.237038] rpm_suspend+0x2dc/0x740
[ 117.241229] pm_runtime_work+0xa0/0xb8
[ 117.245769] process_scheduled_works+0x24c/0x478
[ 117.251007] worker_thread+0x23c/0x328
[ 117.255547] kthread+0x104/0x1b0
[ 117.259389] ret_from_fork+0x10/0x20
[ 117.263582] Code: 54000222 f9461ae8 f8747908 b4ffff48 (f9400100)
Cc: stable@vger.kernel.org # v6.3+
Fixes: a30951d31b ("xhci: tegra: USB2 pad power controls")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20241014042134.27664-1-henryl@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZwu6fw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yly6QCfdXwmKEqG4H7xonERzmEkP9/sYtoAnAsafKV5
5pWgy7Jw+WH1s1L7IzGy
=xrG1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
net/9p/usbg: Fix build error
USB: yurex: kill needless initialization in yurex_read
Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
usb: xhci: Fix problem with xhci resume from suspend
usb: misc: onboard_usb_dev: introduce new config symbol for usb5744 SMBus support
usb: dwc3: core: Stop processing of pending events if controller is halted
usb: dwc3: re-enable runtime PM after failed resume
usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
usb: gadget: core: force synchronous registration
I have a ASUS PN51 S mini pc that has two xhci devices. One from AMD,
and other from ASMEDIA. The one from ASMEDIA have problems when resume
from suspend, and keep broken until unplug the power cord. I use this
kernel parameter: xhci-hcd.quirks=128 and then it works ok. I make a
path to reset only the ASMEDIA xhci.
Signed-off-by: Jose Alberto Reguero <jose.alberto.reguero@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240919184202.22249-1-jose.alberto.reguero@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup of
the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART engine
that that chip seems to have. Hopefully it's in a better state now,
but hardware designers still seem to come up with more ways to make
broken UARTS 40+ years after this all should have finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvUz1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAhwCcCw/6BX3aKGTyx7ZxeMRc/mjbSLIAoMUv6bGT
6H04ZvcSd63ZotAWeZsn
=PWB8
-----END PGP SIGNATURE-----
Merge tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
Don't populate the read-only const arrays fifoaddr, fifosel and fifoctr
on the stack at run time, instead make them static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240912132345.589397-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse software managed property 'xhci-skip-phy-init-quirk' and
'xhci-skip-phy-init-quirk' to apply related quirk. It allows usb glue layer
driver apply these quirk.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-1-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow creators of seconday interrupters to specify the interrupt
moderation interval value in nanoseconds when creating the interrupter.
If not sure what value to use then use the xhci driver default
xhci->imod_interval
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI xHC host should be stopped and xhci driver memory freed before putting
host to PCI D3 state during PCI remove callback.
Hosts with XHCI_SPURIOUS_WAKEUP quirk did this the wrong way around
and set the host to D3 before calling usb_hcd_pci_remove(dev), which will
access the host to stop it, and then free xhci.
Fixes: f1f6d9a8b5 ("xhci: don't dereference a xhci member after removing xhci")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce an initial check for an empty list prior to entering the while
loop. Which enables, the implementation of distinct warnings to
differentiate between scenarios where the list is initially empty and
when it has been emptied during processing skipped isoc TDs.
These adjustments not only simplifies the large while loop, but also
facilitates future enhancements to the handle_tx_event() function.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HCD does not allocate or request interrupt for the xhci driver, but HCD
does free and sync xhci interrupts in some cases. Add comment detailing
in which cases HCD will free/sync xhci interrupts.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'sbrn' is used to store the Serial Bus Release Number, which is
then only used for a debug message. Thus, 'sbrn' can be a local variable
and assigned after the primary HCD check. The SBRN debug message is only
printed when a primary HCD is setup.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Completion codes 'COMP_SUCCESS' and 'COMP_SHORT_PACKET' are the most
frequently encountered completion codes. Typically, these codes do not
trigger a default debug message but rather a warning that indicates a
potential issue. This behavior is consistent across all transfer types
with the exception of Bulk transfers. To reduce unnecessary log clutter,
remove the Bulk 'COMP_SHORT_PACKET' debug message.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removed debug messages trigger each time an isoc frame is handled.
In case of an error, a dedicated debug message exists.
For example, a 60fps USB camera will trigger the debug message every 0.6s.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we move the requests from the read_queue to the end of the
read_pool list, avoiding looping and using the same one request all
the time.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't flush all pending DbC data requests when an endpoint halts.
An endpoint may halt and xHC DbC triggers a STALL error event if there's
an issue with a bulk data transfer. The transfer should restart once xHC
DbC receives a ClearFeature(ENDPOINT_HALT) request from the host.
Once xHC DbC restarts it will start from the TRB pointed to by dequeue
field in the endpoint context, which might be the same TRB we got the
STALL event for. Turn the TRB to a no-op in this case to make sure xHC
DbC doesn't reuse and tries to retransmit this same TRB after we already
handled it, and gave its corresponding data request back.
Other STALL events might be completely bogus.
Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events
if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted
endpoints even without any active bulk transfers.
Assume STALL event is spurious if it reports 0 bytes transferred, and
the endpoint stopped on the STALLED TRB.
Don't give back the data request corresponding to the TRB in this case.
The halted status is per endpoint. Track it with a per endpoint flag
instead of the driver invented DbC wide DS_STALLED state.
DbC remains in DbC-Configured state even if endpoints halt. There is no
Stalled state in the DbC Port state Machine (xhci section 7.6.6)
Reported-by: Łukasz Bartosik <ukaszb@chromium.org>
Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'tunnel_mode' enum to usb device structure to describe if a USB3
link is tunneled over USB4, or connected directly using native USB2/USB3
protocols.
Tunneled devices depend on USB4 NHI host to maintain the tunnel.
Knowledge about tunneled devices is important to ensure correct
suspend and resume order between USB4 hosts and tunneled devices.
i.e. make sure tunnel is up before the USB device using it resumes.
USB hosts such as xHCI may have vendor specific ways to detect tunneled
connections. This 'tunnel_mode' parameter can be set by USB3 host driver
during hcd->driver->update_device(hcd, udev) callback.
tunnel_mode can be set to:
USB_LINK_UNKNOWN = 0
USB_LINK_NATIVE
USB_LINK_TUNNELED
USB_LINK_UNKNOWN is used in case host is not capable of detecting
tunneled links.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Knowledge about tunneled devices is useful in order to correctly describe
the relationship between tunneled USB3 device and USB4 Host Interface,
ensuring proper suspend and resume order, and to be able to power down
Thunderbolt if there is no need for tunneling.
Intel hosts share if a USB3 connection is native or tunneled via vendor
specific "SPR eSS PORT" registers.
These vendor registers are available if host supports a vendor specific
SPR shadow extended capability with ID 206. Registers are per USB3 port
and 0x20 apart.
Knowing the tunneling status of the device connected to roothub is enough
as all its children will have the same status.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
