[ Upstream commit f195fc060c ]
When the task management thread processes reply queues while the reset
thread resets them, the task management thread accesses an invalid queue ID
(0xFFFF), set by the reset thread, which points to unallocated memory,
causing a crash.
Add flag 'io_admin_reset_sync' to synchronize access between the reset,
I/O, and admin threads. Before a reset, the reset handler sets this flag to
block I/O and admin processing threads. If any thread bypasses the initial
check, the reset thread waits up to 10 seconds for processing to finish. If
the wait exceeds 10 seconds, the controller is marked as unrecoverable.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20250129100850.25430-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f08b24d827 ]
To avoid reply queue full condition, update the driver to check IOCFacts
capabilities for qfull.
Update the operational reply queue's Consumer Index after processing 100
replies. If pending I/Os on a reply queue exceeds a threshold
(reply_queue_depth - 200), then return I/O back to OS to retry.
Also increase default admin reply queue size to 2K.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20250129100850.25430-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5233e3235d ]
A null dereference or oops exception will eventually occur when qla1280.c
driver is compiled with DEBUG_QLA1280 enabled and ql_debug_level > 2. I
think its clear from the code that the intention here is sg_dma_len(s) not
length of sg_next(s) when printing the debug info.
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20250125095033.26188-1-linmag7@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5363ee9d11 ]
Filesystems can write to disk from page reclaim with __GFP_FS
set. Marc found a case where scsi_realloc_sdev_budget_map() ends up in
page reclaim with GFP_KERNEL, where it could try to take filesystem
locks again, leading to a deadlock.
WARNING: possible circular locking dependency detected
6.13.0 #1 Not tainted
------------------------------------------------------
kswapd0/70 is trying to acquire lock:
ffff8881025d5d78 (&q->q_usage_counter(io)){++++}-{0:0}, at: blk_mq_submit_bio+0x461/0x6e0
but task is already holding lock:
ffffffff81ef5f40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x9f/0x760
The full lockdep splat can be found in Marc's report:
https://lkml.org/lkml/2025/1/24/1101
Avoid the potential deadlock by doing the allocation with GFP_NOIO, which
prevents both filesystem and block layer recursion.
Reported-by: Marc Aurèle La France <tsi@tuyoix.net>
Signed-off-by: Rik van Riel <riel@surriel.com>
Link: https://lore.kernel.org/r/20250129104525.0ae8421e@fangorn
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce5c4afd0 ]
After commit 1bad6c4a57 ("scsi: zero per-cmd private driver data for each
MQ I/O"), the xen-scsifront/virtio_scsi/snic drivers all removed code that
explicitly zeroed driver-private command data.
In combination with commit 464a00c9e0 ("scsi: core: Kill DRIVER_SENSE"),
after virtio_scsi performs a capacity expansion, the first request will
return a unit attention to indicate that the capacity has changed. And then
the original command is retried. As driver-private command data was not
cleared, the request would return UA again and eventually time out and fail.
Zero driver-private command data when a request is retried.
Fixes: f7de50da14 ("scsi: xen-scsifront: Remove code that zeroes driver-private command data")
Fixes: c2bb87318b ("scsi: virtio_scsi: Remove code that zeroes driver-private command data")
Fixes: c3006a9264 ("scsi: snic: Remove code that zeroes driver-private command data")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20250217021628.2929248-1-yebin@huaweicloud.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9ff7c383b8 upstream.
Fail I/Os instead of retry to prevent user space processes from being
blocked on the I/O completion for several minutes.
Retrying I/Os during "depopulation in progress" or "depopulation restore in
progress" results in a continuous retry loop until the depopulation
completes or until the I/O retry loop is aborted due to a timeout by the
scsi_cmd_runtime_exceeced().
Depopulation is slow and can take 24+ hours to complete on 20+ TB HDDs.
Most I/Os in the depopulation retry loop end up taking several minutes
before returning the failure to user space.
Cc: stable@vger.kernel.org # 4.18.x: 2bbeb8d scsi: core: Handle depopulation and restoration in progress
Cc: stable@vger.kernel.org # 4.18.x
Fixes: e37c7d9a03 ("scsi: core: sanitize++ in progress")
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20250131184408.859579-1-ipylypiv@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87c4b5e8a6 upstream.
In StorVSC, payload->range.len is used to indicate if this SCSI command
carries payload. This data is allocated as part of the private driver data
by the upper layer and may get passed to lower driver uninitialized.
For example, the SCSI error handling mid layer may send TEST_UNIT_READY or
REQUEST_SENSE while reusing the buffer from a failed command. The private
data section may have stale data from the previous command.
If the SCSI command doesn't carry payload, the driver may use this value as
is for communicating with host, resulting in possible corruption.
Fix this by always initializing this value.
Fixes: be0cf6ca30 ("scsi: storvsc: Set the tablesize based on the information given by the host")
Cc: stable@kernel.org
Tested-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Long Li <longli@microsoft.com>
Link: https://lore.kernel.org/r/1737601642-7759-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 841df27d61 upstream.
Currently FCE Tracing is enabled to log additional ELS events. Instead,
user will enable or disable this feature through debugfs.
Modify existing DFS knob to allow user to enable or disable this
feature.
echo [1 | 0] > /sys/kernel/debug/qla2xxx/qla2xxx_??/fce
cat /sys/kernel/debug/qla2xxx/qla2xxx_??/fce
Cc: stable@vger.kernel.org
Fixes: df613b9607 ("[SCSI] qla2xxx: Add Fibre Channel Event (FCE) tracing support.")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98b37881b7 upstream.
Commit 9604eea5bd ("scsi: st: Add third party poweron reset handling") in
v6.6 added new code to handle the Power On/Reset Unit Attention (POR UA)
sense data. This was in addition to the existing method. When this Unit
Attention is received, the driver blocks attempts to read, write and some
other operations because the reset may have rewinded the tape. Because of
the added code, also the initial POR UA resulted in blocking operations,
including those that are used to set the driver options after the device is
recognized. Also, reading and writing are refused, whereas they succeeded
before this commit.
Add code to not set pos_unknown to block operations if the POR UA is
received from the first test_ready() call after the st device has been
created. This restores the behavior before v6.6.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20241216113755.30415-1-Kai.Makisara@kolumbus.fi
Fixes: 9604eea5bd ("scsi: st: Add third party poweron reset handling")
CC: stable@vger.kernel.org
Closes: https://lore.kernel.org/linux-scsi/2201CF73-4795-4D3B-9A79-6EE5215CF58D@kolumbus.fi/
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 295006f6e8 ]
If bsg_setup_queue() fails, the bsg_queue is assigned a non-NULL value.
Consequently, in mpi3mr_bsg_exit(), the condition "if(!mrioc->bsg_queue)"
will not be satisfied, preventing execution from entering
bsg_remove_queue(), which could lead to the following crash:
BUG: kernel NULL pointer dereference, address: 000000000000041c
Call Trace:
<TASK>
mpi3mr_bsg_exit+0x1f/0x50 [mpi3mr]
mpi3mr_remove+0x6f/0x340 [mpi3mr]
pci_device_remove+0x3f/0xb0
device_release_driver_internal+0x19d/0x220
unbind_store+0xa4/0xb0
kernfs_fop_write_iter+0x11f/0x200
vfs_write+0x1fc/0x3e0
ksys_write+0x67/0xe0
do_syscall_64+0x38/0x80
entry_SYSCALL_64_after_hwframe+0x78/0xe2
Fixes: 4268fa7513 ("scsi: mpi3mr: Add bsg device support")
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250107022032.24006-1-kanie@linux.alibaba.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad7c3c0cb8 ]
Currently, the code does:
if (x == 0) {
x &= ~0x3;
x |= 0x1;
}
Zeroing bits 0 and 1 of a variable that is 0 is not necessary. So directly
set the variable to 1.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20241212221817.78940-2-pmenzel@molgen.mpg.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d2138eab8c upstream.
If there's a persistent error in the hypervisor, the SCSI warning for
failed I/O can flood the kernel log and max out CPU utilization,
preventing troubleshooting from the VM side. Ratelimit the warning so
it doesn't DoS the VM.
Closes: https://github.com/microsoft/WSL/issues/9173
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Link: https://lore.kernel.org/r/20250107-eahariha-ratelimit-storvsc-v1-1-7fc193d1f2b0@linux.microsoft.com
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63ca02221c ]
The ISCSI_UEVENT_GET_HOST_STATS request is already handled in
iscsi_get_host_stats(). This fix ensures that redundant responses are
skipped in iscsi_if_rx().
- On success: send reply and stats from iscsi_get_host_stats()
within if_recv_msg().
- On error: fall through.
Signed-off-by: Xiang Zhang <hawkxiang.cpp@gmail.com>
Link: https://lore.kernel.org/r/20250107022432.65390-1-hawkxiang.cpp@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1aee7f034 ]
This partially reverts commit 812fe6420a ("scsi: storvsc: Handle
additional SRB status values").
HyperV does not support MAINTENANCE_IN resulting in FC passthrough
returning the SRB_STATUS_DATA_OVERRUN value. Now that
SRB_STATUS_DATA_OVERRUN is treated as an error, multipath ALUA paths go
into a faulty state as multipath ALUA submits RTPG commands via
MAINTENANCE_IN.
[ 3.215560] hv_storvsc 1d69d403-9692-4460-89f9-a8cbcc0f94f3:
tag#230 cmd 0xa3 status: scsi 0x0 srb 0x12 hv 0xc0000001
[ 3.215572] scsi 1:0:0:32: alua: rtpg failed, result 458752
Make MAINTENANCE_IN return success to avoid the error path as is
currently done with INQUIRY and MODE_SENSE.
Suggested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Cathy Avery <cavery@redhat.com>
Link: https://lore.kernel.org/r/20241127181324.3318443-1-cavery@redhat.com
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb6eb98f39 ]
Before retrying initialization, check and abort if the fault code
indicates insufficient power. Also mark the controller as unrecoverable
instead of issuing reset in the watch dog timer if the fault code
indicates insufficient power.
Signed-off-by: Prayas Patel <prayas.patel@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110194405.10108-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d32014f1e ]
Instead of displaying the controller index starting from '1' make the
driver display the controller index starting from '0'.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110194405.10108-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 711201a8b8 ]
The driver, through the SAS transport, exposes a sysfs interface to
enable/disable PHYs in a controller/expander setup. When multiple PHYs
are disabled and enabled in rapid succession, the persistent and current
config pages related to SAS IO unit/SAS Expander pages could get
corrupted.
Use separate memory for each config request.
Signed-off-by: Prayas Patel <prayas.patel@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110194405.10108-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 367ac16e5f ]
The driver serializes ioctls through a mutex lock but access to the
ioctl data buffer is not guarded by the mutex. This results in multiple
user threads being able to write to the driver's ioctl buffer
simultaneously.
Protect the ioctl buffer with the ioctl mutex.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110194405.10108-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f5eb062e8 ]
Issue a Diag-Reset when the "Doorbell-In-Use" bit is set during the
driver load/initialization.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110173341.11595-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c064de86d2 ]
Fix the hardware revision numbering for Qlogic ISP1020/1040 boards. HWMASK
suggests that the revision number only needs four bits, this is consistent
with how NetBSD does things in their ISP driver. Verified on a IPS1040B
which is seen as rev 5 not as BIT_4.
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20241113225636.2276-1-linmag7@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b120edb37 ]
Most drives rewind the tape when the device is reset. Reading and writing
are not allowed until something is done to make the tape position match the
user's expectation (e.g., rewind the tape). Add MTIOCGET and MTLOAD to
operations allowed after reset. MTIOCGET is modified to not touch the tape
if pos_unknown is non-zero. The tape location is known after MTLOAD.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219419#c14
Link: https://lore.kernel.org/r/20241106095723.63254-3-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4281f44ea8 ]
Current dev_loss_tmo handling checks whether there has been a previous
call to unregister with SCSI transport. If so, the NDLP kref count is
decremented a second time in dev_loss_tmo as the final kref release.
However, this can sometimes result in a reference count underflow if
there is also a race to unregister with NVMe transport as well. Add a
check for NVMe transport registration before decrementing the final
kref. If NVMe transport is still registered, then the NVMe transport
unregistration is designated as the final kref decrement.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-8-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98f8d35880 ]
The lpfc_cmpl_ct_disc_fdmi() routine has incorrect logic that treats an
FDMI completion with error LOCAL_REJECT/SLI_ABORTED as a success status.
Under the erroneous assumption of successful completion, the routine
proceeds to issue follow up FDMI commands, which may never complete if
the HBA is in an errata state as indicated by the errored completion
status. Fix by freeing FDMI cmd resources and early return when the
LPFC_SLI_ACTIVE flag is not set and a LOCAL_REJECT/SLI_ABORTED or
SLI_DOWN status is received.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-6-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d35f767271 ]
During initialization, the driver allocates wq->pring in lpfc_wq_create
and lpfc_sli4_queue_unset() is the only place where kfree(wq->pring) is
called.
There is a possible memory leak in lpfc_sli_brdrestart_s4() (restart)
and lpfc_pci_remove_one_s4() (rmmod) paths because there are no calls to
lpfc_sli4_queue_unset() to kfree() the wq->pring.
Fix by inserting a call to lpfc_sli4_queue_unset() in
lpfc_sli_brdrestart_s4() and lpfc_sli4_hba_unset() routines. Also, add
a check for the SLI_ACTIVE flag before issuing the Q_DESTROY mailbox
command. If not set, then the mailbox command will obviously fail. In
such cases, skip issuing the mailbox command and only execute the driver
resource clean up portions of the lpfc_*q_destroy routines.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-4-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 833c70e212 upstream.
Firmware supports multiple sg_cnt for request and response for CT
commands, so remove the redundant check. A check is there where sg_cnt
for request and response should be same. This is not required as driver
and FW have code to handle multiple and different sg_cnt on request and
response.
Cc: stable@vger.kernel.org
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07c903db0a upstream.
System crash is observed with stack trace warning of use after
free. There are 2 signals to tell dpc_thread to terminate (UNLOADING
flag and kthread_stop).
On setting the UNLOADING flag when dpc_thread happens to run at the time
and sees the flag, this causes dpc_thread to exit and clean up
itself. When kthread_stop is called for final cleanup, this causes use
after free.
Remove UNLOADING signal to terminate dpc_thread. Use the kthread_stop
as the main signal to exit dpc_thread.
[596663.812935] kernel BUG at mm/slub.c:294!
[596663.812950] invalid opcode: 0000 [#1] SMP PTI
[596663.812957] CPU: 13 PID: 1475935 Comm: rmmod Kdump: loaded Tainted: G IOE --------- - - 4.18.0-240.el8.x86_64 #1
[596663.812960] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 08/20/2012
[596663.812974] RIP: 0010:__slab_free+0x17d/0x360
...
[596663.813008] Call Trace:
[596663.813022] ? __dentry_kill+0x121/0x170
[596663.813030] ? _cond_resched+0x15/0x30
[596663.813034] ? _cond_resched+0x15/0x30
[596663.813039] ? wait_for_completion+0x35/0x190
[596663.813048] ? try_to_wake_up+0x63/0x540
[596663.813055] free_task+0x5a/0x60
[596663.813061] kthread_stop+0xf3/0x100
[596663.813103] qla2x00_remove_one+0x284/0x440 [qla2xxx]
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4e268f898 upstream.
The fc_function_template for vports was missing the
.show_host_supported_speeds. The base port had the same.
Add .show_host_supported_speeds to the vport template as well.
Cc: stable@vger.kernel.org
Fixes: 2c3dfe3f6a ("[SCSI] qla2xxx: add support for NPIV")
Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4812b7796c upstream.
NVMe controller fails to send connect command due to failure to locate
hw context buffer for NVMe queue 0 (blk_mq_hw_ctx, hctx_idx=0). The
cause of the issue is NPIV host did not initialize the vha->irq_offset
field. This field is given to blk-mq (blk_mq_pci_map_queues) to help
locate the beginning of IO Queues which in turn help locate NVMe queue
0.
Initialize this field to allow NVMe to work properly with NPIV host.
kernel: nvme nvme5: Connect command failed, errno: -18
kernel: nvme nvme5: qid 0: secure concatenation is not supported
kernel: nvme nvme5: NVME-FC{5}: create_assoc failed, assoc_id 2e9100 ret 401
kernel: nvme nvme5: NVME-FC{5}: reset: Reconnect attempt failed (401)
kernel: nvme nvme5: NVME-FC{5}: Reconnect attempt in 2 seconds
Cc: stable@vger.kernel.org
Fixes: f0783d43dd ("scsi: qla2xxx: Use correct number of vectors for online CPUs")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6918141d81 ]
Since commit 771f712ba5 ("scsi: scsi_debug: Fix cmd duration
calculation"), ns_from_boot value is only evaluated in schedule_resp()
for polled requests.
However, ns_from_boot is also required for hrtimer support for when
ndelay is less than INCLUSIVE_TIMING_MAX_NS, so fix up the logic to
decide when to evaluate ns_from_boot.
Fixes: 771f712ba5 ("scsi: scsi_debug: Fix cmd duration calculation")
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20241202130045.2335194-1-john.g.garry@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f10593ad9b ]
Fix a use-after-free bug in sg_release(), detected by syzbot with KASAN:
BUG: KASAN: slab-use-after-free in lock_release+0x151/0xa30
kernel/locking/lockdep.c:5838
__mutex_unlock_slowpath+0xe2/0x750 kernel/locking/mutex.c:912
sg_release+0x1f4/0x2e0 drivers/scsi/sg.c:407
In sg_release(), the function kref_put(&sfp->f_ref, sg_remove_sfp) is
called before releasing the open_rel_lock mutex. The kref_put() call may
decrement the reference count of sfp to zero, triggering its cleanup
through sg_remove_sfp(). This cleanup includes scheduling deferred work
via sg_remove_sfp_usercontext(), which ultimately frees sfp.
After kref_put(), sg_release() continues to unlock open_rel_lock and may
reference sfp or sdp. If sfp has already been freed, this results in a
slab-use-after-free error.
Move the kref_put(&sfp->f_ref, sg_remove_sfp) call after unlocking the
open_rel_lock mutex. This ensures:
- No references to sfp or sdp occur after the reference count is
decremented.
- Cleanup functions such as sg_remove_sfp() and
sg_remove_sfp_usercontext() can safely execute without impacting the
mutex handling in sg_release().
The fix has been tested and validated by syzbot. This patch closes the
bug reported at the following syzkaller link and ensures proper
sequencing of resource cleanup and mutex operations, eliminating the
risk of use-after-free errors in sg_release().
Reported-by: syzbot+7efb5850a17ba6ce098b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7efb5850a17ba6ce098b
Tested-by: syzbot+7efb5850a17ba6ce098b@syzkaller.appspotmail.com
Fixes: cc833acbee ("sg: O_EXCL and other lock handling")
Signed-off-by: Suraj Sonawane <surajsonawane0215@gmail.com>
Link: https://lore.kernel.org/r/20241120125944.88095-1-surajsonawane0215@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4045de893f ]
In 2010, runtime power management support was implemented in the SCSI
core. The description of patch "[SCSI] implement runtime Power
Management" mentions that the sg driver is skipped but not why. This
patch enables runtime power management even if an instance of the sg
driver is held open. Enabling runtime PM for the sg driver is safe
because all interactions of the sg driver with the SCSI device pass
through the block layer (blk_execute_rq_nowait()) and the block layer
already supports runtime PM.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Fixes: bc4f24014d ("[SCSI] implement runtime Power Management")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241030220310.1373569-1-bvanassche@acm.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95bbdca499 ]
Hook "qedi_ops->common->sb_init = qed_sb_init" does not release the DMA
memory sb_virt when it fails. Add dma_free_coherent() to free it. This
is the same way as qedr_alloc_mem_sb() and qede_alloc_mem_sb().
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20241026125711.484-3-thunder.leizhen@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c62c30429d ]
Hook "qed_ops->common->sb_init = qed_sb_init" does not release the DMA
memory sb_virt when it fails. Add dma_free_coherent() to free it. This
is the same way as qedr_alloc_mem_sb() and qede_alloc_mem_sb().
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20241026125711.484-2-thunder.leizhen@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08a07dc71d ]
For the controller reset operation(such as FLR or clear nexus ha in SCSI
EH), we will disable all PHYs and then enable PHY based on the
hisi_hba->phy_state obtained in hisi_sas_controller_reset_prepare(). If
the device is removed before controller reset or the PHY is not attached
to any device in directly attached scenario, the corresponding bit of
phy_state is not set. After controller reset done, the PHY is disabled.
The device cannot be identified even if user reconnect the disk.
Therefore, for PHYs that are not disabled by user, hisi_sas_phy_enable()
needs to be executed even if the corresponding bit of phy_state is not
set.
Fixes: 89954f024c ("scsi: hisi_sas: Ensure all enabled PHYs up during controller reset")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-5-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Two small fixes, the drivers one in ufs simply delays running a work
queue and the generic one in zoned storage switches to a more correct
API that tries the standard buddy allocator first (for small
allocations); this fixes an allocation problem with small allocations
seen under memory pressure.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZy5pZSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdonAQCeHKnp
BkxbSls2uPQn4DAxak1tCfxTujMFWxQHP2Y92gEA2q3chF7P136z2rYp0wGfm7P4
ivxddAWZth4tV7TUUw8=
=by5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, the drivers one in ufs simply delays running a work
queue and the generic one in zoned storage switches to a more correct
API that tries the standard buddy allocator first (for small
allocations); this fixes an allocation problem with small allocations
seen under memory pressure"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Start the RTC update work later
scsi: sd_zbc: Use kvzalloc() to allocate REPORT ZONES buffer
We have two reports of failed memory allocation in btrfs' code which is
calling into report zones.
Both of these reports have the following signature coming from
__vmalloc_area_node():
kworker/u17:5: vmalloc error: size 0, failed to allocate pages, mode:0x10dc2(GFP_KERNEL|__GFP_HIGHMEM|__GFP_NORETRY|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0
Further debugging showed these where allocations of one sector (512
bytes) and at least one of the reporter's systems where low on memory,
so going through the overhead of allocating a vm area failed.
Switching the allocation from __vmalloc() to kvzalloc() avoids the
overhead of vmalloc() on small allocations and succeeds.
Note: the buffer is already freed using kvfree() so there's no need to
adjust the free path.
Cc: Qu Wenru <wqu@suse.com>
Cc: Naohiro Aota <naohiro.aota@wdc.com>
Link: https://github.com/kdave/btrfs-progs/issues/779
Link: https://github.com/kdave/btrfs-progs/issues/915
Fixes: 23a50861ad ("scsi: sd_zbc: Cleanup sd_zbc_alloc_report_buffer()")
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20241030110253.11718-1-jth@kernel.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Two small fixes, both in drivers (ufs and scsi_debug).
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZyH+cSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVdMAQDdOiaS
9DO+ly/Il64wXZqb9WKcVYRIjmz7m7g5xdMgrgEA1yfD6G7GgQ3zvbVPNC7Y9ecr
4O2iR5EGAVb1Y7UaEQU=
=551G
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, both in drivers (ufs and scsi_debug)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Fix another deadlock during RTC update
scsi: scsi_debug: Fix do_device_access() handling of unexpected SG copy length
If the sg_copy_buffer() call returns less than sdebug_sector_size, then
we drop out of the copy loop. However, we still report that we copied
the full expected amount, which is not proper.
Fix by keeping a running total and return that value.
Fixes: 84f3a3c01d ("scsi: scsi_debug: Atomic write support")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20241018101655.4207-1-john.g.garry@oracle.com
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes all in drivers. The largest is the mpi3mr which corrects a phy
count limit that should only apply to the controller but was being
incorrectly applied to expander phys.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZxQINSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfuiAP9+gxzU
MYpyNFYmS8iwbma+wagKMr2ZxpiIAnQIukBtugD7Baqw7YjNbAPtCcQMgC96y8ac
X7zeMkLTyMqkaIjOQFk=
=eHKZ
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Fixes all in drivers. The largest is the mpi3mr which corrects a phy
count limit that should only apply to the controller but was being
incorrectly applied to expander phys"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: core: Fix null-ptr-deref in target_alloc_device()
scsi: mpi3mr: Validate SAS port assignments
scsi: ufs: core: Set SDEV_OFFLINE when UFS is shut down
scsi: ufs: core: Requeue aborted request
scsi: ufs: core: Fix the issue of ICU failure
A sanity check on phy_mask was added in commit 3668651def ("scsi:
mpi3mr: Sanitise num_phys"). This causes warning messages when more than
64 phys are detected and devices connected to phys greater than 64 are
dropped.
The phy_mask bitmap is only needed for controller phys and not required
for expander phys. Controller phys can go up to a maximum of 64 and
therefore u64 is good enough to contain phy_mask bitmap.
To suppress those warnings and allow devices to be discovered as before
the offending commit, restrict the phy_mask setting and lowest phy
setting only to the controller phys.
Fixes: 3668651def ("scsi: mpi3mr: Sanitise num_phys")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410051943.Mp9o5DlF-lkp@intel.com/
Reported-by: Alexander Motin <mav@ixsystems.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241008074353.200379-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
four small fixes, three in drivers and one in the FC transport class
to add idempotence to state setting.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZwnsDSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZYjAP9QKRk5
1i/g9TyqFCurbt+R4BJGiNg+89WUnLxgNbThsgD9FqmXRsm2mGok02lQS4bz5Asv
OkNVO2se/q6IlplijV8=
=RCJc
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes, three in drivers and one in the FC transport class
to add idempotence to state setting"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_transport_fc: Allow setting rport state to current state
scsi: wd33c93: Don't use stale scsi_pointer value
scsi: fnic: Move flush_work initialization out of if block
scsi: ufs: Use pre-calculated offsets in ufshcd_init_lrb()
The only input fc_rport_set_marginal_state() currently accepts is
"Marginal" when port_state is "Online", and "Online" when the port_state
is "Marginal". It should also allow setting port_state to its current
state, either "Marginal or "Online".
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Link: https://lore.kernel.org/r/20240917230643.966768-1-bmarzins@redhat.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A regression was introduced with commit dbb2da557a ("scsi: wd33c93:
Move the SCSI pointer to private command data") which results in an oops
in wd33c93_intr(). That commit added the scsi_pointer variable and
initialized it from hostdata->connected. However, during selection,
hostdata->connected is not yet valid. Fix this by getting the current
scsi_pointer from hostdata->selecting.
Cc: Daniel Palmer <daniel@0x0f.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@kernel.org
Fixes: dbb2da557a ("scsi: wd33c93: Move the SCSI pointer to private command data")
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Co-developed-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/09e11a0a54e6aa2a88bd214526d305aaf018f523.1727926187.git.fthain@linux-m68k.org
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
