commit 83964a2937 upstream.
The current solution for powering off the Apalis iMX6 is not functioning
as intended. To resolve this, it is necessary to power off the
vgen2_reg, which will also set the POWER_ENABLE_MOCI signal to a low
state. This ensures the carrier board is properly informed to initiate
its power-off sequence.
The new solution uses the regulator-poweroff driver, which will power
off the regulator during a system shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 4eb56e26f9 ("ARM: dts: imx6q-apalis: Command pmic to standby for poweroff")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24d4c56dd6 ]
After using the device for a while, Tom reports that he initially described
the switch port labels incorrectly. Apparently, ASUS's own firmware also
describes them incorrectly. Correct them to what is seen on the chassis.
Reported-by: Tom Brautaset <tbrautaset@gmail.com>
Fixes: b116239094 ("ARM: dts: BCM5301X: Add DT for ASUS RT-AC3200")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/r/20250304-for-broadcom-fix-rt-ac3200-switch-ports-v1-1-7e249a19a13e@arinc9.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56e12d0c8d ]
After using the device for a while, Tom reports that he initially described
the switch port labels incorrectly. Correct them.
Reported-by: Tom Brautaset <tbrautaset@gmail.com>
Fixes: 961dedc6b4 ("ARM: dts: BCM5301X: Add DT for ASUS RT-AC5300")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/r/20250303-for-broadcom-fix-rt-ac5300-switch-ports-v1-1-e058856ef4d3@arinc9.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c24f272ae7 ]
During upstream process of Raspberry Pi 4 back in 2019 the ARMv7 stubs
didn't configured the ARM architectural timer. This firmware issue has
been fixed in 2020, which gave users enough time to update their system.
So drop this property to allow the use of the vDSO version of
clock_gettime.
Link: https://github.com/raspberrypi/tools/pull/113
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250222094113.48198-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de09025f1 ]
The ARM PL011 UART instances in BCM2711 are r1p5 spec, which means they
have 32-entry FIFOs. The correct periphid value for this is 0x00341011.
Thanks to N Buchwitz for pointing this out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250223125614.3592-2-wahrenst@gmx.net
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f44fa354a0 ]
During s2idle tests on the Raspberry CM4 the VPU firmware always crashes
on xHCI power-domain resume:
root@raspberrypi:/sys/power# echo freeze > state
[ 70.724347] xhci_suspend finished
[ 70.727730] xhci_plat_suspend finished
[ 70.755624] bcm2835-power bcm2835-power: Power grafx off
[ 70.761127] USB: Set power to 0
[ 74.653040] USB: Failed to set power to 1 (-110)
This seems to be caused because of the mixed usage of
raspberrypi-power and bcm2835-power at the same time. So avoid
the usage of the VPU firmware power-domain driver, which
prevents the VPU crash.
Fixes: 522c35e08b ("ARM: dts: bcm2711: Add BCM2711 xHCI support")
Link: https://github.com/raspberrypi/linux/issues/6537
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250201112729.31509-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0cfbd7805f upstream.
Despite CM_IDLEST1_CORE and CM_FCLKEN1_CORE behaving normal,
disabling SPI leads to messages like when suspending:
Powerdomain (core_pwrdm) didn't enter target state 0
and according to /sys/kernel/debug/pm_debug/count off state is not
entered. That was not connected to SPI during the discussion
of disabling SPI. See:
https://lore.kernel.org/linux-omap/20230122100852.32ae082c@aktux/
The reason is that SPI is per default in slave mode. Linux driver
will turn it to master per default. It slave mode, the powerdomain seems to
be kept active if active chip select input is sensed.
Fix that by explicitly disabling the SPI3 pins which used to be muxed by
the bootloader since they are available on an optionally fitted header
which would require dtb overlays anyways.
Fixes: a622310f7f ("ARM: dts: gta04: fix excess dma channel usage")
CC: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241204174152.2360431-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1472ec1dc upstream.
A bus_dma_limit was added for l3 bus by commit cfb5d65f25
("ARM: dts: dra7: Add bus_dma_limit for L3 bus") to fix an issue
observed only with SATA on DRA7-EVM with 4GB RAM and CONFIG_ARM_LPAE
enabled.
Since kernel 5.13, the SATA issue can be reproduced again following
the SATA node move from L3 bus to L4_cfg in commit 8af15365a3
("ARM: dts: Configure interconnect target module for dra7 sata").
Fix it by adding an empty dma-ranges property to l4_cfg and
segment@100000 nodes (parent device tree node of SATA controller) to
inherit the 2GB dma ranges limit from l3 bus node.
Note: A similar fix was applied for PCIe controller by commit
90d4d3f4ea ("ARM: dts: dra7: Fix bus_dma_limit for PCIe").
Fixes: 8af15365a3 ("ARM: dts: Configure interconnect target module for dra7 sata").
Link: https://lore.kernel.org/linux-omap/c583e1bb-f56b-4489-8012-ce742e85f233@smile.fr/
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Romain Naour <romain.naour@skf.com>
Link: https://lore.kernel.org/r/20241115102537.1330300-1-romain.naour@smile.fr
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d9e5965df ]
Add no-1-8-v property to sdmmc0 node to keep VDDSDMMC power rail at 3.3V.
This property will stop the LDO regulator from switching to 1.8V when the
MMC core detects an UHS SD Card. VDDSDMMC power rail is used by all the
SDMMC interface pins in GPIO mode (PA0 - PA13).
On this board, PA10 is used as GPIO to enable the power switch controlling
USB Vbus for the USB Host. The change is needed to fix the PA10 voltage
level to 3.3V instead of 1.8V.
Fixes: 5d4c3cfb63 ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20241119160107.598411-3-cristian.birsan@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c21c23a0f2 ]
Add no-1-8-v property to sdmmc0 node to keep VDDSDMMC power rail at 3.3V.
This property will stop the LDO regulator from switching to 1.8V when the
MMC core detects an UHS SD Card. VDDSDMMC power rail is used by all the
SDMMC interface pins in GPIO mode (PA0 - PA13).
On this board, PA6 is used as GPIO to enable the power switch controlling
USB Vbus for the USB Host. The change is needed to fix the PA6 voltage
level to 3.3V instead of 1.8V.
Fixes: d85c4229e9 ("ARM: dts: at91: sama5d29_curiosity: Add device tree for sama5d29_curiosity board")
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20241119160107.598411-2-cristian.birsan@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 479b8227ff ]
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73317d3271 ]
Deduplicate /aliases { serialN = ... } and /chosen node into
stm32mp15xx-dhcom-som.dtsi , since the content is identical
on all carrier boards using the STM32MP15xx DHCOM SoM. No
functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 479b8227ff ("ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62a40a0d56 ]
The ahb reset is deasserted in probe before first register access, while the
stmmacheth-ocp reset needs to be asserted every time before changing the phy
mode in Arria10[1].
Changed in Upstream to "ahb"(331085a423b arm64: dts: socfpga: change the
reset-name of "stmmaceth-ocp" to "ahb" ).This change was intended for arm64
socfpga and it is not applicable to Arria10.
Further with STMMAC-SELFTEST Driver enabled, ethtool test also FAILS.
$ ethtool -t eth0
[ 322.946709] socfpga-dwmac ff800000.ethernet eth0: entered promiscuous mode
[ 323.374558] socfpga-dwmac ff800000.ethernet eth0: left promiscuous mode
The test result is FAIL
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -110
3. MMC Counters -110
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC -110
7. MC Filter -110
8. UC Filter 0
9. Flow Control -110
10. RSS -95
11. VLAN Filtering -95
12. VLAN Filtering (perf) -95
13. Double VLAN Filter -95
14. Double VLAN Filter (perf) -95
15. Flexible RX Parser -95
16. SA Insertion (desc) -95
17. SA Replacement (desc) -95
18. SA Insertion (reg) -95
19. SA Replacement (reg) -95
20. VLAN TX Insertion -95
21. SVLAN TX Insertion -95
22. L3 DA Filtering -95
23. L3 SA Filtering -95
24. L4 DA TCP Filtering -95
25. L4 SA TCP Filtering -95
26. L4 DA UDP Filtering -95
27. L4 SA UDP Filtering -95
28. ARP Offload -95
29. Jumbo Frame -110
30. Multichannel Jumbo -95
31. Split Header -95
32. TBS (ETF Scheduler) -95
[ 324.881327] socfpga-dwmac ff800000.ethernet eth0: Link is Down
[ 327.995360] socfpga-dwmac ff800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Link:[1] https://www.intel.com/content/www/us/en/docs/programmable/683711/21-2/functional-description-of-the-emac.html
Fixes: 331085a423 ("arm64: dts: socfpga: change the reset-name of "stmmaceth-ocp" to "ahb")
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ea654242e ]
The GIC IRQ type used for IPCC RX should be IRQ_TYPE_LEVEL_HIGH.
Replacing the interrupt with the EXTI event changes the type to
the numeric value 1, meaning IRQ_TYPE_EDGE_RISING.
The issue is that EXTI event 61 is a direct event.The IRQ type of
direct events is not used by EXTI and is propagated to the parent
IRQ controller of EXTI, the GIC.
Align the IRQ type to the value expected by the GIC by replacing
the second parameter "1" with IRQ_TYPE_LEVEL_HIGH.
Fixes: 7d9802bb0e ("ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4422a9183 ]
The STM32MP13xx DHCOR DHSBC is populated with STM32MP13xx part capable
of 1 GHz operation, increase the CPU core voltage to 1.35 V to make
sure the SoC is stable even if the blobs unconditionally force the CPU
to 1 GHz operation.
It is not possible to make use of CPUfreq on the STM32MP13xx because
the SCMI protocol 0x13 is not implemented by upstream OpTee-OS which
is the SCMI provider.
Fixes: 6331bddce6 ("ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 96a64e9730 upstream.
Operating stable without reduced chip life at 1Ghz needs several
technologies working: The technologies involve
- SmartReflex
- DVFS
As this cannot directly specified in the OPP table as dependecies in the
devicetree yet, use the turbo flag again to mark this OPP as something
special to have some kind of opt-in.
So revert commit
5f1bf7ae84 ("ARM: dts: omap36xx: Remove turbo mode for 1GHz variants")
Practical reasoning:
At least the GTA04A5 (DM3730) has become unstable with that OPP enabled.
Furthermore nothing enforces the availability of said technologies,
even in the kernel configuration, so allow users to rather opt-in.
Cc: Stable@vger.kernel.org
Fixes: 5f1bf7ae84 ("ARM: dts: omap36xx: Remove turbo mode for 1GHz variants")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20241018214727.275162-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd36ad71ad ]
The DCDC5 voltage rail in the X-Powers AXP809 PMIC has a resolution of
50mV, so the currently enforced limits of 1.475 and 1.525 volts cannot
be set, when the existing regulator value is beyond this range.
This will lead to the whole regulator driver to give up and fail
probing, which in turn will hang the system, as essential devices depend
on the PMIC.
In this case a bug in U-Boot set the voltage to 1.75V (meant for DCDC4),
and the AXP driver's attempt to correct this lead to this error:
==================
[ 4.447653] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
[ 4.450066] vcc-dram: Bringing 1750000uV into 1575000-1575000uV
[ 4.460272] vcc-dram: failed to apply 1575000-1575000uV constraint: -EINVAL
[ 4.474788] axp20x-regulator axp20x-regulator.0: Failed to register dcdc5
[ 4.482276] axp20x-regulator axp20x-regulator.0: probe with driver axp20x-regulator failed with error -22
==================
Set the limits to values that can be programmed, so any correction will
be successful.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: 1e1dea7265 ("ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators")
Link: https://patch.msgid.link/20241007222916.19013-1-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f9d013a0c ]
Add the atmel,usart-mode property to the UART nodes. This ensures
compliance with the atmel,at91-usart.yaml schema and resolves the errors
below:
serial@200: $nodename:0: 'serial@200' does not match
'^spi(@.*|-([0-9]|[1-9][0-9]+))?$'
serial@200: atmel,use-dma-rx: False schema does not allow True
serial@200: atmel,use-dma-tx: False schema does not allow True
serial@200: atmel,fifo-size: False schema does not allow [[16]]
These errors indicate that the property
atmel,usart-mode = <AT91_USART_MODE_SERIAL> is missing for
UART nodes 0, 1, 2, 3, 4, 6, 7, 8, 9, 10, 11, and 12.
Fixes: 99c8083358 ("ARM: dts: at91: sam9x60: Add missing flexcom definitions")
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20240912093307.40488-1-andrei.simion@microchip.com
[claudiu.beznea: move the atmel,usart-mode close to vendor specific
properties to cope with DTS coding style]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Both the node name as well as the compatible were not named
according to the binding expectations, fix that.
Fixes: 47bf3a5c9e ("ARM: dts: rockchip: add the sound setup for rk3036-kylin board")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-15-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Compatible and clock names did not match the existing binding.
So set the correct values and re-order+rename the clocks.
It looks like no rk3036 board did use the spi controller so far,
so this was never detected on a running device yet.
Fixes: f629fcfab2 ("ARM: dts: rockchip: support the spi for rk3036")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-14-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Neither the binding nor the driver implementation specify/use the grf
reference provided in the rk3036. And neither does the newer rk3128
user of the hdmi controller. So drop the rockchip,grf property.
Fixes: b7217cf19c ("ARM: dts: rockchip: add hdmi device node for rk3036")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-13-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The acodec node is not conformant to the binding.
Set the correct nodename, use the correct compatible, add the needed
#sound-dai-cells and sort the rockchip,grf below clocks properties
as expected.
Fixes: faea098e18 ("ARM: dts: rockchip: add core rk3036 dtsi")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-12-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This concludes a long journey towards replacing the old
board files with devictree description on the Cirrus Logic
EP93xx platform.
Nikita Shubin has been working on this for a long time,
for details see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/
-----BEGIN PGP SIGNATURE-----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=Y3Cd
-----END PGP SIGNATURE-----
Merge tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
New SoC support for Broadcom bcm2712 (Raspberry Pi 5) and Renesas
R9A09G057 (RZ/V2H(P)) and Qualcomm Snapdragon 414 (MSM8929), all three
of these are variants of already supported chips, in particular the last
one is almost identical to MSM8939.
Lots of updates to Mediatek, ASpeed, Rockchips, Amlogic, Qualcomm,
STM32, NXP i.MX, Sophgo, TI K3, Renesas, Microchip at91, NVIDIA Tegra,
and T-HEAD.
The added Qualcomm platform support once again dominates the changes,
with seven phones and three laptops getting added in addition to
many new features on existing machines. The Snapdragon X1E support
specifically keeps improving.
The other new machines are:
- eight new machines using various 64-bit Rockchips SoCs, both
on the consumer/gaming side and developer boards
- three industrial boards with 64-bit i.MX, which is a very
low number for them.
- four more servers using a 32-bit Speed BMC
- three boards using STM32MP1 SoCs
- one new machine each using allwinner, amlogic, broadcom
and renesas chips.
-----BEGIN PGP SIGNATURE-----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=r07W
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC devicetree updates from Arnd Bergmann:
"New SoC support for Broadcom bcm2712 (Raspberry Pi 5) and Renesas
R9A09G057 (RZ/V2H(P)) and Qualcomm Snapdragon 414 (MSM8929), all three
of these are variants of already supported chips, in particular the
last one is almost identical to MSM8939.
Lots of updates to Mediatek, ASpeed, Rockchips, Amlogic, Qualcomm,
STM32, NXP i.MX, Sophgo, TI K3, Renesas, Microchip at91, NVIDIA Tegra,
and T-HEAD.
The added Qualcomm platform support once again dominates the changes,
with seven phones and three laptops getting added in addition to many
new features on existing machines. The Snapdragon X1E support
specifically keeps improving.
The other new machines are:
- eight new machines using various 64-bit Rockchips SoCs, both on the
consumer/gaming side and developer boards
- three industrial boards with 64-bit i.MX, which is a very low
number for them.
- four more servers using a 32-bit Speed BMC
- three boards using STM32MP1 SoCs
- one new machine each using allwinner, amlogic, broadcom and renesas
chips"
* tag 'soc-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (672 commits)
arm64: dts: allwinner: h5: NanoPi NEO Plus2: Use regulators for pio
arm64: dts: mediatek: add audio support for mt8365-evk
arm64: dts: mediatek: add afe support for mt8365 SoC
arm64: dts: mediatek: mt8186-corsola: Disable DPI display interface
arm64: dts: mediatek: mt8186: Add svs node
arm64: dts: mediatek: mt8186: Add power domain for DPI
arm64: dts: mediatek: mt8195: Correct clock order for dp_intf*
arm64: dts: mt8183: add dpi node to mt8183
arm64: dts: allwinner: h5: NanoPi Neo Plus2: Fix regulators
arm64: dts: rockchip: add CAN0 and CAN1 interfaces to mecsbc board
arm64: dts: rockchip: add CAN-FD controller nodes to rk3568
arm64: dts: nuvoton: ma35d1: Add uart pinctrl settings
arm64: dts: nuvoton: ma35d1: Add pinctrl and gpio nodes
arm64: dts: nuvoton: Add syscon to the system-management node
ARM: dts: Fix undocumented LM75 compatible nodes
arm64: dts: toshiba: Fix pl011 and pl022 clocks
ARM: dts: stm32: Use SAI to generate bit and frame clock on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Switch bitclock/frame-master to flag on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Sort properties in audio endpoints on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Add MECIO1 and MECT1S board variants
...
Add device tree file for Technologic Systems ts7250 board and
Liebherr bk3 board which have many in common, both are based on
ep9302 SoC variant.
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
6.12, please pull the following:
- Andrea adds a minimal Device Tree for the Raspberry Pi 5 (2712)
- Stefan adjusts the bcm2837/bcm2712 bcm2836-l1-intc node name to
conform to the binding changes
-----BEGIN PGP SIGNATURE-----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=k60v
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmbhWaMACgkQYKtH/8kJ
UicGcxAAm7XTkPudtXfgboLLCOnK2YfY6JpdDwFS4iRp6H+qZD5A2UoDWMZRUKO6
p3u08EEwADeBe3iPyxLFxCoPuoh9VV1qDELojZxa7QxQEZxZB3EXa7LOhEUojAwG
LP1W+Aa20NarWbWYg+g1dH4Xpxt5zF2ON2lI5TPElQ2QQ3JgEl9TVDsrLgHHJFPz
CQ7MSFhJZTWLxeZAjMH+a9HuNFPgOyvNMjXskBCNLoHsfb3/6BSEzLKvsZURoZxI
nMffM7D+n1WvyL5hEMdNr2WduTOrMjnrqSzQw1XxPMXsZQmt+4p19I8NNJXKpL7X
jK8rzHEgHZNgNPhjMHWrwasrmrsnUdV+cBiGn+xp9Hhjoyd/EhnZUXr6nyhe4xEO
FVV14Xmq3T7xTW30S/rDd6+Bfr5xzB2e5CSBoQXaPo1nGnEWDWDQxAIyRT7qnSQw
A9/Dyrv/1bME5FNdX1tpP8rBALP7wD/kC4FIaHPwBcptDqZTWhzIrgO3zTEt8eaW
DijYnIfisunW54HS6+ad+lAL9zYKEIHuXPALN5jY7BjAUG0nnrVxwYLTAEHmdXlw
1aOPCjI2R8tk3lcFsnVKS4HcQKxxElYoNHD8Orf751KBMsGMlgAkcCLU4grKt0NY
hRQi5+Zx003hhhLHWSep2CK/lAa0qHlvkucewM+sOqoKvKFSSNM=
=y4Wd
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-6.12/devicetree-arm64' of https://github.com/Broadcom/stblinux into soc/dt
This pull request contains Broadcom ARM64 SoCs Device Tree changes for
6.12, please pull the following:
- Andrea adds a minimal Device Tree for the Raspberry Pi 5 (2712)
- Stefan adjusts the bcm2837/bcm2712 bcm2836-l1-intc node name to
conform to the binding changes
* tag 'arm-soc/for-6.12/devicetree-arm64' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837/bcm2712: adjust local intc node names
arm64: dts: broadcom: Add minimal support for Raspberry Pi 5
Link: https://lore.kernel.org/r/20240906180643.2275460-2-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
please pull the following:
- Krzysztof documents the AVS monitor binding present on 2711 (Raspberry
Pi 4)
- Rafal updates the Broadcom Northstar DTS files to use the recent NVMEM
binding
- Artur factors the nodes between the BCM21664 and BCM23550 SoCs since
they are nearly identical
- Stefan converts the bcm2835-system-timer and bcm2836-l1-intc to a YAML
binding syntax
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAmbZ48EACgkQh9CWnEQH
BwTAexAAz8usfam1HCq1HC611CGcdPAv/twpi+E3edRVKu/ZM+DX6GxUC9MyCAcw
GKN6Y4sn8cFSs2dPgIS0OqM65PSZhxcCiTVoSkBG17/IFWv8pwJyiPbYatt5oalS
cqIuDnagA35ff2XA1/gU5ymbDF0MN9/XwtzkZ+eznF7weFs4BrOH4cvQZeggSQj/
OBy9s4QWrbEbZz/Lzw9tIG+dRGGO037IqhgEUAcagKG9Qg1YvPPi/xtGR+yguJ4n
g5exzJw9vLWeiBagrL7YXzWrEnKK0aql+XlutbJpyUhRV1spxigQ3NMCeglHawRC
Ra09zVWou6sXdyzzatO7UVtpzjR66XiAiG6yqICfnVl54rsBj6OjnFeVfobzkTEm
6HqiSNlHLGQAo6H5tH7wwE4Kp1yvj1mMvy4l7TF/E3D3cp4vmKleYHdtZmHoiOAH
E9V7GIKyTTU+q19RI5Aq0gIKk48rMJsaXfalE8Cdb/HOGZ/DC7yOitBEVIaU7a6e
a9zDZPVv0XJ3od+ifKHny4sdcAE/FdrgVrsiJPzbxTZReLJ4w+YiD4NO7Qbeiu77
RgiMxzLKdDDQdVf5wKGrqEZmh/NO3wLzBjRDxzWj0JW/ZCZ8iSclaO2sRYJa3L/Q
zWc+peCanRKcIuO6X4M3XqH0Ot7ekjTTraF1ZQAxqlb8LSXK4Ws=
=pLbU
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=S1tP
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-6.12/devicetree' of https://github.com/Broadcom/stblinux into soc/dt
This pull request contains Broadcom SoCs Device Tree changes for 6.12,
please pull the following:
- Krzysztof documents the AVS monitor binding present on 2711 (Raspberry
Pi 4)
- Rafal updates the Broadcom Northstar DTS files to use the recent NVMEM
binding
- Artur factors the nodes between the BCM21664 and BCM23550 SoCs since
they are nearly identical
- Stefan converts the bcm2835-system-timer and bcm2836-l1-intc to a YAML
binding syntax
* tag 'arm-soc/for-6.12/devicetree' of https://github.com/Broadcom/stblinux:
dt-bindings: interrupt-controller: convert bcm2836-l1-intc to yaml
dt-bindings: timer: convert bcm2835-system-timer bindings to YAML
ARM: dts: bcm-mobile: Split out nodes used by both BCM21664 and BCM23550
ARM: dts: broadcom: bcm21664: Move chosen node into Garnet DTS
ARM: dts: broadcom: convert NVMEM content to layout syntax
dt-bindings: soc: bcm: document brcm,bcm2711-avs-monitor
Link: https://lore.kernel.org/r/20240906180643.2275460-1-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Realview: correct unit addresses (e.g. drop when not valid).
2. Nuvoton: correct node name to match bindings.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAmbbC+cQHGtyemtAa2Vy
bmVsLm9yZwAKCRDBN2bmhouD13QXD/46ZJM2sy0bXQvs3kK5kpxsYPjvAZjx66QN
KbXotlQKlJGb3pqAIravdtxTucA8x2j/B9Grg1p0KFRK0OWlMbuQz6ZPjN7JA69r
6P0NU4GxKp2Huc5rEPZcdg58dO0ZqACu6VUaf8VKMnKGIS2LYml1IUeZixwUccDn
SFoXlvrwXy9NS4VdpsDYyrvDQvvkbjCEMRwIX+f61lzO87jIVg1PA6cFc2Vht1VR
z3iXsJFAGsNqZq0ims++rtbQDcXSJeXx341dG4rZ+lHoe7SA1jDwmUNL2UXWaCdt
5hWYhLbbK+G8qIHmWDNzTNrCt/+mItNGEBv0JTeDB0ETvrDGpn/KcfQpn4eoohPf
JAl8/HHkngeGgGtEPqwhNjHj8h24TCXbPFno+HbtOZeMUs9173CNJAUTgGIKdaBB
spdZsskmHxS9v07Slf3BD7bXXFgyzAW9zIlt6zYro+md5v7+p+oEWn84wPcloEdI
ABcFGkfQ2gck4QT5hYNbSgjpFSikq35CumRanNeqrqPdY3PE0oihkCE/Xbvej2z7
k9z/EZvd9dPN5OfV0NXY+GI50eTaSPMEZpvr6A3SmasNJyumBUICZPIel7Mpe9Zd
fbqjG9j+x7xA3tASKRXMcseLjHi0bIFYutfNrMPNVxS7wJHRe32KdUGTy+k8MT+H
6NJFso1Sxw==
=MTME
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=2GTJ
-----END PGP SIGNATURE-----
Merge tag 'dt-cleanup-6.12' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements in ARM DTS for v6.12
1. Realview: correct unit addresses (e.g. drop when not valid).
2. Nuvoton: correct node name to match bindings.
* tag 'dt-cleanup-6.12' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: nuvoton: wpcm450: align LED and GPIO keys node name with bindings
arm: dts: realview: Add/drop missing/spurious unit-addreses
Link: https://lore.kernel.org/r/20240906140513.71307-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"lm75" without any vendor is undocumented. It works with the Linux
kernel since the I2C subsystem will do matches of the compatible string
without a vendor prefix to the i2c_device_id and/or driver name.
Mostly replace "lm75" with "national,lm75" as that's the original part
vendor and the compatible which matches what "lm75" matched with. In a
couple of cases the node name or compatible gives a clue to the actual
part and vendor and a more specific compatible can be used. In these
cases, it does change the variant the kernel picks.
"nct75" is an OnSemi part which is compatible with TI TMP75C based on
a comparison of the OnSemi NCT75 datasheet and configuration the Linux
driver uses. Adding an OnSemi compatible would be an ABI change.
"nxp,lm75" is most likely an NXP part. Alexander Stein says the i.MX53
boards are a NXP LM75A as well. NXP makes a LM75A and LM75B. Both are
11-bit resolution and 100ms sample time. The "national,lm75a" is
9-bit, so "national,lm75b" is the closest match for both NXP variants.
While we're here, fix the node names to use the generic name
"temperature-sensor".
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com> # am335x-nano.dts
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx53-mba53.dts, imx53-tqma53.dtsi
Link: https://lore.kernel.org/r/20240816164717.1585629-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series from Fabio Estevam to fix dt-schema warnings on i.MX23,
i.MX28 and i.MX27 device trees
- A bunch of changes from Krzysztof Kozlowski that corrects TQ Systems
DTS patterns in MAINTAINERS file and fix various dt-schema warnings
- A couple changes from Liu Ying to improve HDMI support on i.MX53 QSB
board
- A series from Lukasz Majewski to update imx28-lwe device tree, fixing
partition definitions, reducing SPI frequency and cleaning up SAIF
- A series from Markus Niebel to improve TQ-Systems device trees, adding
iio-hwmon device, using better compatible for LM75 temp sensor, moving
I2C3 pinmux to a better place
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmbYVjoUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7oPgf9FKYcNHDzVh4X2NFyPvqYJiJrq6tT
8Po/UvgymzF6DkYMw7vDWthYCiH9PUpjk3nP7kv+xSDq4YOfkHshVYbOwqBACeSb
XtP5vS9RIVGU6G2ZhQ+lYM3d9Uc3hCRBCRBuCzUg8p7msp0a0gIYQbEOL3bBfBcr
KwhOM8nF+LJ4/4L3MUjQPEJRmoHsFMSZXGvVEpFiHNKwh8qByW9j/cPNey1aIMpe
GY+/J71qyvEy/lXS081gdec+VM8Y3GpoDPq8EIOri2xqms1fwihIiAcpUNngR8PN
REXzRbk0uT9MUwPE794qZxqCb+W1etVUHVhdfxN29CjWW7CYf3yhB6ePrg==
=fPHr
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=QOO+
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-6.12' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree changes for 6.12:
- A series from Fabio Estevam to fix dt-schema warnings on i.MX23,
i.MX28 and i.MX27 device trees
- A bunch of changes from Krzysztof Kozlowski that corrects TQ Systems
DTS patterns in MAINTAINERS file and fix various dt-schema warnings
- A couple changes from Liu Ying to improve HDMI support on i.MX53 QSB
board
- A series from Lukasz Majewski to update imx28-lwe device tree, fixing
partition definitions, reducing SPI frequency and cleaning up SAIF
- A series from Markus Niebel to improve TQ-Systems device trees, adding
iio-hwmon device, using better compatible for LM75 temp sensor, moving
I2C3 pinmux to a better place
* tag 'imx-dt-6.12' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (27 commits)
ARM: dts: imx28-lwe: Remove saif[01] definitions
ARM: dts: imx28-lwe: Reduce maximal SPI frequency
ARM: dts: imx28-lwe: Fix partitions definitions
ARM: dts: imx6qdl: align pin config nodes with bindings
ARM: dts: imx6sl: align pin config nodes with bindings
ARM: dts: imx6ul: align pin config nodes with bindings
ARM: dts: imx6ul-tx6ul: drop empty pinctrl placeholder
ARM: dts: imx28-tx28: Fix the fsl,saif-master usage
ARM: dts: imx6ull-seeed-npi: fix fsl,pins property in tscgrp pinctrl
ARM: dts: imx6ul-geam: fix fsl,pins property in tscgrp pinctrl
ARM: dts: imx23/8: Rename apbh and apbx nodes
ARM: dts: imx6qdl-mba6b: remove doubled entry for I2C1 pinmux
ARM: dts: imx6qdl-mba6: improve compatible for LM75 temp sensor
ARM: dts: imx6qdl-tqma6: improve compatible for LM75 temp sensor
ARM: dts: imx6qdl-tqma6: move i2c3 pinmux to imx6qdl-tqma6b
ARM: dts: imx7d-sdb: align pin config nodes with bindings
ARM: dts: imx7: align pin config nodes with bindings
ARM: dts: imx7d-zii-rmu2: fix Ethernet PHY pinctrl property
MAINTAINERS: correct TQ Systems DTS patterns
ARM: dts: imx6: update spdif sound card node properties
...
Link: https://lore.kernel.org/r/20240904143439.211552-4-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
By default the SGTL5000 derives bit and frame clock from MCLK, which
does not produce particularly accurate results. The SGTL5000 PLL does
improve the accuracy, but also increases power consumption. Using the
SoC SAI interface as bit and frame clock source results in the best
accuracy without the power consumption increase downside. Switch the
bit and frame clock direction from SAI to SGTL5000, reduce mclk-fs to
match.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Switch the bitclock-master and frame-master properties from phandle to
flag on STM32MP15xx DHCOM PDK2. There is no real reason to use phandle
in this system DT, since the phandle points to the endpoint node which
contains the property itself. Simplify the DT. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
