Commit graph

18,945 commits

Author SHA1 Message Date
Stephan Gerhold
cd9d354bdd arm64: dts: qcom: x1e80100: Add GPU cooling
[ Upstream commit 5ba21fa11f ]

Unlike the CPU, the GPU does not throttle its speed automatically when it
reaches high temperatures. With certain high GPU loads it is possible to
reach the critical hardware shutdown temperature of 120°C, endangering the
hardware and making it impossible to run certain applications.

Set up GPU cooling similar to the ACPI tables, by throttling the GPU speed
when reaching 95°C and polling every 200ms.

Cc: stable@vger.kernel.org
Fixes: 721e38301b ("arm64: dts: qcom: x1e80100: Add gpu support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-3-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:23 +02:00
Stephan Gerhold
9cd06b2ebe arm64: dts: qcom: x1e80100: Apply consistent critical thermal shutdown
[ Upstream commit 03f2b8eed7 ]

The firmware configures the TSENS controller with a maximum temperature of
120°C. When reaching that temperature, the hardware automatically triggers
a reset of the entire platform. Some of the thermal zones in x1e80100.dtsi
use a critical trip point of 125°C. It's impossible to reach those.

It's preferable to shut down the system cleanly before reaching the
hardware trip point. Make the critical temperature trip points consistent
by setting all of them to 115°C and apply a consistent hysteresis.
The ACPI tables also specify 115°C as critical shutdown temperature.

Cc: stable@vger.kernel.org
Fixes: 4e915987ff ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-2-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:23 +02:00
Julien Massot
0007761ff5 arm64: dts: mt6359: Rename RTC node to match binding expectations
[ Upstream commit cfe035d866 ]

Rename the node 'mt6359rtc' to 'rtc', as required by the binding.

Fix the following dtb-check error:

mediatek/mt8395-radxa-nio-12l.dtb: pmic: 'mt6359rtc' do not match
any of the regexes: 'pinctrl-[0-9]+'

Fixes: 3b7d143be4 ("arm64: dts: mt6359: add PMIC MT6359 related nodes")
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250514-mt8395-dtb-errors-v2-3-d67b9077c59a@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:03 +02:00
Thuan Nguyen
0e00819914 arm64: dts: renesas: white-hawk-ard-audio: Fix TPU0 groups
[ Upstream commit 652eea251d ]

White Hawk ARD audio uses a clock generated by the TPU, but commit
3d144ef10a ("pinctrl: renesas: r8a779g0: Fix TPU suffixes") renamed
pin group "tpu_to0_a" to "tpu_to0_b".  Update DTS accordingly otherwise
the sound driver does not receive a clock signal.

Fixes: 3d144ef10a ("pinctrl: renesas: r8a779g0: Fix TPU suffixes")
Signed-off-by: Thuan Nguyen <thuan.nguyen-hong@banvien.com.vn>
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/TYCPR01MB8740608B675365215ADB0374B49CA@TYCPR01MB8740.jpnprd01.prod.outlook.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:03 +02:00
Dmitry Baryshkov
81f52f39ed arm64: dts: qcom: qcm2290: fix (some) of QUP interconnects
[ Upstream commit e07d2d57a1 ]

While adding interconnect support for the QCM2290 platform some of them
got the c&p error, rogue MASTER_APPSS_PROC for the config_noc
interconnect. Turn that into SLAVE_QUP_0 as expected.

Fixes: 5b970ff019 ("arm64: dts: qcom: qcm2290: Hook up interconnects")
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250207-rb1-bt-v4-4-d810fc8c94a9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:02 +02:00
Quentin Schulz
16f35dcfe3 arm64: dts: rockchip: disable unrouted USB controllers and PHY on RK3399 Puma with Haikou
[ Upstream commit febd8c6ab5 ]

The u2phy0_host port is the part of the USB PHY0 (namely the
HOST0_DP/DM lanes) which routes directly to the USB2.0 HOST
controller[1]. The other lanes of the PHY are routed to the USB3.0 OTG
controller (dwc3), which we do use.

The HOST0_DP/DM lanes aren't routed on RK3399 Puma so let's simply
disable the USB2.0 controllers.

USB3 OTG has been known to be unstable on RK3399 Puma Haikou for a
while, one of the recurring issues being that only USB2 is detected and
not USB3 in host mode. Reading the justification above and seeing that
we are keeping u2phy0_host in the Haikou carrierboard DTS probably may
have bothered you since it should be changed to u2phy0_otg. The issue is
that if it's switched to that, USB OTG on Haikou is entirely broken. I
have checked the routing in the Gerber file, the lanes are going to the
expected ball pins (that is, NOT HOST0_DP/DM).
u2phy0_host is for sure the wrong part of the PHY to use, but it's the
only one that works at the moment for that board so keep it until we
figure out what exactly is broken.

No intended functional change.

[1] https://rockchip.fr/Rockchip%20RK3399%20TRM%20V1.3%20Part2.pdf
    Chapter 2 USB2.0 PHY

Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-5-4a76a474a010@thaumatec.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:02 +02:00
Prasanth Babu Mantena
14f2820a5d arm64: dts: ti: k3-j721e-common-proc-board: Enable OSPI1 on J721E
[ Upstream commit 6b8deb2ff0 ]

J721E SoM has MT25QU512AB Serial NOR flash connected to
OSPI1 controller. Enable ospi1 node in device tree.

Fixes: 73676c480b ("arm64: dts: ti: k3-j721e: Enable OSPI nodes at the board level")
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Link: https://lore.kernel.org/r/20250507050701.3007209-1-p-mantena@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:01 +02:00
Aaron Kling
2e39a12c45 arm64: tegra: Add uartd serial alias for Jetson TX1 module
[ Upstream commit dfb25484bd ]

If a serial-tegra interface does not have an alias, the driver fails to
probe with an error:
serial-tegra 70006300.serial: failed to get alias id, errno -19
This prevents the bluetooth device from being accessible.

Fixes: 6eba6471bb ("arm64: tegra: Wire up Bluetooth on Jetson TX1 module")
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://lore.kernel.org/r/20250420-tx1-bt-v1-1-153cba105a4e@gmail.com
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:00 +02:00
Aaron Kling
39ecf2ad20 arm64: tegra: Drop remaining serial clock-names and reset-names
[ Upstream commit 4cd763297c ]

The referenced commit only removed some of the names, missing all that
weren't in use at the time. The commit removes the rest.

Fixes: 71de0a054d ("arm64: tegra: Drop serial clock-names and reset-names")
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Link: https://lore.kernel.org/r/20250428-tegra-serial-fixes-v1-1-4f47c5d85bf6@gmail.com
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:00 +02:00
Peter Robinson
827746ce8b arm64: dts: rockchip: Update eMMC for NanoPi R5 series
[ Upstream commit 8eca9e979a ]

Add the 3.3v and 1.8v regulators that are connected to
the eMMC on the R5 series devices, as well as adding the
eMMC data strobe, and enable eMMC HS200 mode as the
Foresee FEMDNN0xxG-A3A55 modules support it.

Fixes: c8ec73b05a ("arm64: dts: rockchip: create common dtsi for NanoPi R5 series")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250506222531.625157-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:00 +02:00
Peter Robinson
4fd50f6980 arm64: dts: rockchip: Add vcc-supply to SPI flash on rk3566-rock3c
[ Upstream commit a706a593cb ]

As described in the radxa_rock_3c_v1400_schematic.pdf, the SPI Flash's
VCC connector is connected to VCCIO_FLASH and according to the
that same schematic, that belongs to the VCC_1V8 power source.

This fixes the following warning:

  spi-nor spi4.0: supply vcc not found, using dummy regulator

Fixes: ee219017dd ("arm64: dts: rockchip: Add Radxa ROCK 3C")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20250506195702.593044-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:00 +02:00
Alexey Minnekhanov
f924280cf4 arm64: dts: qcom: sda660-ifc6560: Fix dt-validate warning
[ Upstream commit f5110806b4 ]

If you remove clocks property, you should remove clock-names, too.
Fixes warning with dtbs check:

 'clocks' is a dependency of 'clock-names'

Fixes: 34279d6e3f ("arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support")
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250504115120.1432282-4-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:00 +02:00
Alexey Minnekhanov
2533efb0d6 arm64: dts: qcom: sdm660-lavender: Add missing USB phy supply
[ Upstream commit dbf62a117a ]

Fixes the following dtbs check error:

 phy@c012000: 'vdda-pll-supply' is a required property

Fixes: e5d3e752b0 ("arm64: dts: qcom: sdm660-xiaomi-lavender: Add USB")
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250504115120.1432282-3-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:00 +02:00
Julien Massot
3c8f511a65 arm64: dts: mt6359: Add missing 'compatible' property to regulators node
[ Upstream commit 1fe38d2a19 ]

The 'compatible' property is required by the
'mfd/mediatek,mt6397.yaml' binding. Add it to fix the following
dtb-check error:
mediatek/mt8395-radxa-nio-12l.dtb: pmic: regulators:
'compatible' is a required property

Fixes: 3b7d143be4 ("arm64: dts: mt6359: add PMIC MT6359 related nodes")
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Link: https://lore.kernel.org/r/20250505-mt8395-dtb-errors-v1-3-9c4714dcdcdb@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:32:00 +02:00
Nícolas F. R. A. Prado
e2df43c942 arm64: dts: mediatek: mt6357: Drop regulator-fixed compatibles
[ Upstream commit d77e89b7b0 ]

Some of the regulators in the MT6357 PMIC dtsi have compatible set to
regulator-fixed, even though they don't serve any purpose: all those
regulators are handled as a whole by the mt6357-regulator driver. In
fact this is the only dtsi in this family of chips where this is the
case: mt6359 and mt6358 don't have any such compatibles.

A side-effect caused by this is that the DT kselftest, which is supposed
to identify nodes with compatibles that can be probed, but haven't,
shows these nodes as failures.

Remove the useless compatibles to move the dtsi in line with the others
in its family and fix the DT kselftest failures.

Fixes: 55749bb478 ("arm64: dts: mediatek: add mt6357 device-tree")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20250502-mt6357-regulator-fixed-compatibles-removal-v1-1-a582c16743fe@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:59 +02:00
Adam Ford
66a6daa0ef arm64: dts: imx8mn-beacon: Set SAI5 MCLK direction to output for HDMI audio
[ Upstream commit a747c4dd2a ]

The HDMI bridge chip fails to generate an audio source due to the SAI5
master clock (MCLK) direction not being set to output. This prevents proper
clocking of the HDMI audio interface.

Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure
the MCLK is driven by the SoC, resolving the HDMI sound issue.

Fixes: 1d6880ceef ("arm64: dts: imx8mn-beacon: Add HDMI video with sound")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:59 +02:00
Adam Ford
b9c7c4e6c8 arm64: dts: imx8mm-beacon: Set SAI5 MCLK direction to output for HDMI audio
[ Upstream commit 8c716f80df ]

The HDMI bridge chip fails to generate an audio source due to the SAI5
master clock (MCLK) direction not being set to output. This prevents proper
clocking of the HDMI audio interface.

Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure
the MCLK is driven by the SoC, resolving the HDMI sound issue.

Fixes: 8ad7d14d99 ("arm64: dts: imx8mm-beacon: Add HDMI video with sound")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:59 +02:00
Adam Ford
c48fe69e17 arm64: dts: imx8mp-beacon: Fix RTC capacitive load
[ Upstream commit 6821ee1753 ]

Although not noticeable when used every day, the RTC appears to drift when
left to sit over time.  This is due to the capacitive load not being
properly set. Fix RTC drift by correcting the capacitive load setting
from 7000 to 12500, which matches the actual hardware configuration.

Fixes: 25a5ccdce7 ("arm64: dts: freescale: Introduce imx8mp-beacon-kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:59 +02:00
Adam Ford
69120f3767 arm64: dts: imx8mn-beacon: Fix RTC capacitive load
[ Upstream commit c3f03bec30 ]

Although not noticeable when used every day, the RTC appears to drift when
left to sit over time.  This is due to the capacitive load not being
properly set. Fix RTC drift by correcting the capacitive load setting
from 7000 to 12500, which matches the actual hardware configuration.

Fixes: 36ca3c8ccb ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:59 +02:00
Adam Ford
33ff1f1329 arm64: dts: imx8mm-beacon: Fix RTC capacitive load
[ Upstream commit 2e98d45666 ]

Although not noticeable when used every day, the RTC appears to drift when
left to sit over time.  This is due to the capacitive load not being
properly set. Fix RTC drift by correcting the capacitive load setting
from 7000 to 12500, which matches the actual hardware configuration.

Fixes: 593816fa2f ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:59 +02:00
Pin-yen Lin
e1c84dd136 arm64: dts: mt8183: Add port node to mt8183.dtsi
[ Upstream commit d15059f7be ]

Add the port node to fix the binding schema check. Also update
mt8183-kukui to reference the new port node.

Fixes: 88ec840270 ("arm64: dts: mt8183: Add dsi node")
Fixes: 27eaf34df3 ("arm64: dts: mt8183: config dsi node")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20250423040354.2847447-1-treapking@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:59 +02:00
Alexey Minnekhanov
a39ba524fb arm64: dts: qcom: sdm660-xiaomi-lavender: Add missing SD card detect GPIO
[ Upstream commit 2eca6af667 ]

During initial porting these cd-gpios were missed. Having card detect is
beneficial because driver does not need to do polling every second and it
can just use IRQ. SD card detection in U-Boot is also fixed by this.

Fixes: cf85e9aee2 ("arm64: dts: qcom: sdm660-xiaomi-lavender: Add eMMC and SD")
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415130101.1429281-1-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:58 +02:00
AngeloGioacchino Del Regno
269df4263e arm64: dts: mediatek: mt8195: Reparent vdec1/2 and venc1 power domains
[ Upstream commit 394f290333 ]

By hardware, the first and second core of the video decoder IP
need the VDEC_SOC to be powered up in order to be able to be
accessed (both internally, by firmware, and externally, by the
kernel).
Similarly, for the video encoder IP, the second core needs the
first core to be powered up in order to be accessible.

Fix that by reparenting the VDEC1/2 power domains to be children
of VDEC0 (VDEC_SOC), and the VENC1 to be a child of VENC0.

Fixes: 2b515194bf ("arm64: dts: mt8195: Add power domains controller")
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20250402090615.25871-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:58 +02:00
Chukun Pan
3682d4dd0e arm64: dts: rockchip: Move SHMEM memory to reserved memory on rk3588
[ Upstream commit 8ecd096d01 ]

0x0 to 0xf0000000 are SDRAM memory areas where 0x10f000 is located.
So move the SHMEM memory of arm_scmi to the reserved memory node.

Fixes: c9211fa260 ("arm64: dts: rockchip: Add base DT for rk3588 SoC")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20250401090009.733771-2-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:58 +02:00
Varadarajan Narayanan
3d36b1baf0 arm64: dts: qcom: ipq9574: Fix USB vdd info
[ Upstream commit 4f4c905e6a ]

USB phys in ipq9574 use the 'L5' regulator. The commit ec4f047679
("arm64: dts: qcom: ipq9574: Enable USB") incorrectly specified it as
'L2'. Because of this when the phy module turns off/on its regulators,
the wrong regulator is turned off/on resulting in 2 issues, namely the
correct regulator related to the USB phy is not turned off/on and the
module powered by the incorrect regulator is affected.

Fixes: ec4f047679 ("arm64: dts: qcom: ipq9574: Enable USB")
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250207073545.1768990-2-quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:58 +02:00
Stephan Gerhold
79c8378070 arm64: dts: qcom: sc8280xp-x13s: Drop duplicate DMIC supplies
[ Upstream commit a2e617f4e6 ]

The WCD938x codec provides two controls for each of the MIC_BIASn outputs:

 - "MIC BIASn" enables an internal regulator to generate the output
   with a configurable voltage (qcom,micbiasN-microvolt).

 - "VA MIC BIASn" enables "pull-up mode" that bypasses the internal
   regulator and directly outputs fixed 1.8V from the VDD_PX pin.
   This is intended for low-power VA (voice activation) use cases.

The audio-routing setup for the ThinkPad X13s currently specifies both
as power supplies for the DMICs, but only one of them can be active
at the same time. In practice, only the internal regulator is used
with the current setup because the driver prefers it over pull-up mode.

Make this more clear by dropping the redundant routes to the pull-up
"VA MIC BIASn" supply. There is no functional difference except that we
skip briefly switching to pull-up mode when shutting down the microphone.

Fixes: 2e498f35c3 ("arm64: dts: qcom: sc8280xp-x13s: fix va dmic dai links and routing")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20241203-x1e80100-va-mic-bias-v1-1-0dfd4d9b492c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:58 +02:00
Xilin Wu
6e65650cee arm64: dts: qcom: sm8250: Fix CPU7 opp table
[ Upstream commit 28f997b899 ]

There is a typo in cpu7_opp9. Fix it to get rid of the following
errors.

[    0.198043] cpu cpu7: Voltage update failed freq=1747200
[    0.198052] cpu cpu7: failed to update OPP for freq=1747200

Fixes: 8e0e8016cb ("arm64: dts: qcom: sm8250: Add CPU opp tables")
Signed-off-by: Xilin Wu <wuxilin123@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250308-fix-sm8250-cpufreq-v1-1-8a0226721399@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:57 +02:00
Luca Weiss
3c4aaf3e76 arm64: dts: qcom: sm8350: Reenable crypto & cryptobam
[ Upstream commit 75eefd4744 ]

When num-channels and qcom,num-ees is not provided in devicetree, the
driver will try to read these values from the registers during probe but
this fails if the interconnect is not on and then crashes the system.

So we can provide these properties in devicetree (queried after patching
BAM driver to enable the necessary interconnect) so we can probe
cryptobam without reading registers and then also use the QCE as
expected.

Fixes: 4d29db2043 ("arm64: dts: qcom: sm8350: fix BAM DMA crash and reboot")
Fixes: f1040a7fe8 ("arm64: dts: qcom: sm8350: Add Crypto Engine support")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250212-bam-dma-fixes-v1-1-f560889e65d8@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:57 +02:00
Dzmitry Sankouski
9164f9ae3f arm64: dts: qcom: sdm845-starqltechn: remove excess reserved gpios
[ Upstream commit fb5fce873b ]

Starqltechn has 2 reserved gpio ranges <27 4>, <85 4>.
<27 4> is spi for eSE(embedded Secure Element).
<85 4> is spi for fingerprint.

Remove excess reserved gpio regions.

Fixes: d711b22eee ("arm64: dts: qcom: starqltechn: add initial device tree for starqltechn")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Link: https://lore.kernel.org/r/20250225-starqltechn_integration_upstream-v9-5-a5d80375cb66@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:57 +02:00
Dzmitry Sankouski
d997703f9d arm64: dts: qcom: sdm845-starqltechn: refactor node order
[ Upstream commit cba1dd3d85 ]

Fixes: d711b22eee ("arm64: dts: qcom: starqltechn: add initial device tree for starqltechn")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Link: https://lore.kernel.org/r/20250225-starqltechn_integration_upstream-v9-4-a5d80375cb66@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:57 +02:00
Dzmitry Sankouski
83f1b473bb arm64: dts: qcom: sdm845-starqltechn: fix usb regulator mistake
[ Upstream commit 242e4126ee ]

Usb regulator was wrongly pointed to vreg_l1a_0p875.
However, on starqltechn it's powered from vreg_l5a_0p8.

Fixes: d711b22eee ("arm64: dts: qcom: starqltechn: add initial device tree for starqltechn")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Link: https://lore.kernel.org/r/20250225-starqltechn_integration_upstream-v9-3-a5d80375cb66@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:57 +02:00
Dzmitry Sankouski
caecebc6b9 arm64: dts: qcom: sdm845-starqltechn: remove wifi
[ Upstream commit 2d3dd4b237 ]

Starqltechn has broadcom chip for wifi, so sdm845 wifi part
can be disabled.

Fixes: d711b22eee ("arm64: dts: qcom: starqltechn: add initial device tree for starqltechn")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Fixes: d711b22eee ("arm64: dts: qcom: starqltechn: add initial device  tree for starqltechn")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250225-starqltechn_integration_upstream-v9-2-a5d80375cb66@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:57 +02:00
Konrad Dybcio
bdf8915dad arm64: dts: qcom: x1e80100-romulus: Keep L12B and L15B always on
[ Upstream commit 0783c8b3c0 ]

These regulators power some electronic components onboard. They're
most likely kept online by other pieces of firmware, but you can never
be sure enough.

Fixes: 09d77be560 ("arm64: dts: qcom: Add support for X1-based Surface Laptop 7 devices")
Reported-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250304-topic-sl7_vregs_aon-v1-1-b2dc706e4157@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:57 +02:00
Neil Armstrong
5c721b58d3 arm64: dts: qcom: sm8650: add missing cpu-cfg interconnect path in the mdss node
[ Upstream commit f22be5c1dd ]

The bindings requires the mdp0-mem and the cpu-cfg interconnect path,
add the missing cpu-cfg path to fix the dtbs check error and also to ensure
that MDSS has enough bandwidth to let HLOS write config registers.

Fixes: 9fa33cbca3 ("arm64: dts: qcom: sm8650: correct MDSS interconnects")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250227-topic-sm8x50-mdss-interconnect-bindings-fix-v5-2-bf6233c6ebe5@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:56 +02:00
Neil Armstrong
a999df6f45 arm64: dts: qcom: sm8650: setup gpu thermal with higher temperatures
[ Upstream commit 2250f65b32 ]

On the SM8650, the dynamic clock and voltage scaling (DCVS) for the GPU
is done from the HLOS, but the GPU can achieve a much higher temperature
before failing according the reference downstream implementation.

Set higher temperatures in the GPU trip points corresponding to
the temperatures provided by Qualcomm in the dowstream source, much
closer to the junction temperature and with a higher critical
temperature trip in the case the HLOS DCVS cannot handle the
temperature surge.

The tsens MAX_THRESHOLD is set to 120C on those platforms, so set
the hot to 110C to leave a chance to HLOS to react and critical to
115C to avoid the monitor thermal shutdown.

Fixes: 497624ed55 ("arm64: dts: qcom: sm8650: Throttle the GPU when overheating")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-sm8650-thermal-cpu-idle-v4-2-65e35f307301@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:56 +02:00
Mark Kettenis
4e95465ab9 arm64: dts: qcom: x1e80100: Mark usb_2 as dma-coherent
[ Upstream commit 45bd6ff900 ]

Make this USB controller consistent with the others on this platform.

Fixes: 4af46b7bd6 ("arm64: dts: qcom: x1e80100: Add USB nodes")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250109205232.92336-1-kettenis@openbsd.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-06-19 15:31:56 +02:00
Siddharth Vadapalli
b7550a2584 arm64: dts: ti: k3-j784s4-j742s2-main-common: Fix length of serdes_ln_ctrl
commit 3b62bd1fde upstream.

Commit under Fixes corrected the "mux-reg-masks" property but did not
update the "length" field of the "reg" property to account for the
newly added register offsets which extend the region. Fix this.

Fixes: 38e7f9092e ("arm64: dts: ti: k3-j784s4-j742s2-main-common: Fix serdes_ln_ctrl reg-masks")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250423151612.48848-1-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Siddharth Vadapalli
2ee377336c arm64: dts: ti: k3-j722s-main: Disable "serdes_wiz0" and "serdes_wiz1"
commit 320d8a84f6 upstream.

Since "serdes0" and "serdes1" which are the sub-nodes of "serdes_wiz0"
and "serdes_wiz1" respectively, have been disabled in the SoC file already,
and, given that these sub-nodes will only be enabled in a board file if the
board utilizes any of the SERDES instances and the peripherals bound to
them, we end up in a situation where the board file doesn't explicitly
disable "serdes_wiz0" and "serdes_wiz1". As a consequence of this, the
following errors show up when booting Linux:

  wiz bus@f0000:phy@f000000: probe with driver wiz failed with error -12
  ...
  wiz bus@f0000:phy@f010000: probe with driver wiz failed with error -12

To not only fix the above, but also, in order to follow the convention of
disabling device-tree nodes in the SoC file and enabling them in the board
files for those boards which require them, disable "serdes_wiz0" and
"serdes_wiz1" device-tree nodes.

Fixes: 628e0a0118 ("arm64: dts: ti: k3-j722s-main: Add SERDES and PCIe support")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250417123246.2733923-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Siddharth Vadapalli
07f51c8f01 arm64: dts: ti: k3-j722s-evm: Enable "serdes_wiz0" and "serdes_wiz1"
commit 9d76be5828 upstream.

In preparation for disabling "serdes_wiz0" and "serdes_wiz1" device-tree
nodes in the SoC file, enable them in the board file. The motivation for
this change is that of following the existing convention of disabling
nodes in the SoC file and only enabling the required ones in the board
file.

Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250417123246.2733923-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Yemike Abhilash Chandra
5b9e29e74d arm64: dts: ti: k3-j721e-sk: Add requiried voltage supplies for IMX219
commit c6a20a2502 upstream.

The device tree overlay for the IMX219 sensor requires three voltage
supplies to be defined: VANA (analog), VDIG (digital core), and VDDL
(digital I/O). Add the corresponding voltage supply definitions to
avoid dtbs_check warnings.

Fixes: f767eb9180 ("arm64: dts: ti: k3-j721e-sk: Add overlay for IMX219")
Cc: stable@vger.kernel.org
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Link: https://lore.kernel.org/r/20250415111328.3847502-5-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Yemike Abhilash Chandra
110875e707 arm64: dts: ti: k3-j721e-sk: Remove clock-names property from IMX219 overlay
commit 24ab76e55e upstream.

The IMX219 sensor device tree bindings do not include a clock-names
property. Remove the incorrectly added clock-names entry to avoid
dtbs_check warnings.

Fixes: f767eb9180 ("arm64: dts: ti: k3-j721e-sk: Add overlay for IMX219")
Cc: stable@vger.kernel.org
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Jai Luthra <jai.luthra@linux.dev>
Link: https://lore.kernel.org/r/20250415111328.3847502-4-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Yemike Abhilash Chandra
8a26672180 arm64: dts: ti: k3-j721e-sk: Add DT nodes for power regulators
commit 97b67cc102 upstream.

Add device tree nodes for two power regulators on the J721E SK board.
vsys_5v0: A fixed regulator representing the 5V supply output from the
LM61460 and vdd_sd_dv: A GPIO-controlled TLV71033 regulator.

J721E-SK schematics: https://www.ti.com/lit/zip/sprr438

Fixes: 1bfda92a3a ("arm64: dts: ti: Add support for J721E SK")
Cc: stable@vger.kernel.org
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250415111328.3847502-2-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Yemike Abhilash Chandra
7d6fd34220 arm64: dts: ti: k3-am68-sk: Fix regulator hierarchy
commit 7edf0a4d3b upstream.

Update the vin-supply of the TLV71033 regulator from LM5141 (vsys_3v3)
to LM61460 (vsys_5v0) to match the schematics. Add a fixed regulator
node for the LM61460 5V supply to support this change.

AM68-SK schematics: https://www.ti.com/lit/zip/sprr463

Fixes: a266c180b3 ("arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board")
Cc: stable@vger.kernel.org
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250415111328.3847502-3-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Judith Mendez
a15e563013 arm64: dts: ti: k3-am65-main: Add missing taps to sdhci0
commit f55c9f087c upstream.

For am65x, add missing ITAPDLYSEL values for Default Speed and High
Speed SDR modes to sdhci0 node according to the device datasheet [0].

[0] https://www.ti.com/lit/gpn/am6548

Fixes: eac99d38f8 ("arm64: dts: ti: k3-am654-main: Update otap-del-sel values")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://lore.kernel.org/r/20250429173009.33994-1-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Yemike Abhilash Chandra
e539e3e611 arm64: dts: ti: k3-am62x: Rename I2C switch to I2C mux in OV5640 overlay
commit b22cc402d3 upstream.

The OV5640 device tree overlay incorrectly defined an I2C switch
instead of an I2C mux. According to the DT bindings, the correct
terminology and node definition should use "i2c-mux" instead of
"i2c-switch". Hence, update the same to avoid dtbs_check warnings.

Fixes: 635ed97151 ("arm64: dts: ti: k3-am62x: Add overlays for OV5640")
Cc: stable@vger.kernel.org
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Jai Luthra <jai.luthra@linux.dev>
Link: https://lore.kernel.org/r/20250415111328.3847502-8-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Yemike Abhilash Chandra
0451eef436 arm64: dts: ti: k3-am62x: Rename I2C switch to I2C mux in IMX219 overlay
commit 7b75dd2029 upstream.

The IMX219 device tree overlay incorrectly defined an I2C switch
instead of an I2C mux. According to the DT bindings, the correct
terminology and node definition should use "i2c-mux" instead of
"i2c-switch". Hence, update the same to avoid dtbs_check warnings.

Fixes: 4111db03dc ("arm64: dts: ti: k3-am62x: Add overlay for IMX219")
Cc: stable@vger.kernel.org
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Jai Luthra <jai.luthra@linux.dev>
Link: https://lore.kernel.org/r/20250415111328.3847502-7-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Yemike Abhilash Chandra
8c32e3ca0e arm64: dts: ti: k3-am62x: Remove clock-names property from IMX219 overlay
commit c68ab54a89 upstream.

The IMX219 sensor device tree bindings do not include a clock-names
property. Remove the incorrectly added clock-names entry to avoid
dtbs_check warnings.

Fixes: 4111db03dc ("arm64: dts: ti: k3-am62x: Add overlay for IMX219")
Cc: stable@vger.kernel.org
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Jai Luthra <jai.luthra@linux.dev>
Link: https://lore.kernel.org/r/20250415111328.3847502-6-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Judith Mendez
8cc39fa7dd arm64: dts: ti: k3-am62p-j722s-common-main: Set eMMC clock parent to default
commit 9c6b73fc72 upstream.

Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.

Fixes: b5080c7c1f ("arm64: dts: ti: k3-am62p: Add nodes for more IPs")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250429163337.15634-4-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Judith Mendez
b605a449b6 arm64: dts: ti: k3-am62a-main: Set eMMC clock parent to default
commit 6af731c5de upstream.

Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.

Fixes: d3ae4e8d8b ("arm64: dts: ti: k3-am62a-main: Add sdhci0 instance")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250429163337.15634-3-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:51 +02:00
Judith Mendez
ef60b9ba0d arm64: dts: ti: k3-am62-main: Set eMMC clock parent to default
commit 3a71cdfec9 upstream.

Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.

Fixes: c37c58fdeb ("arm64: dts: ti: k3-am62: Add more peripheral nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250429163337.15634-2-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-06-04 14:43:50 +02:00