[ Upstream commit e7ea5f5b18 ]
The message "Error getting PHY irq. Use polling instead"
is emitted when the mlxbf_gige driver is loaded by the
kernel before the associated gpio-mlxbf driver, and thus
the call to get the PHY IRQ fails since it is not yet
available. The driver probe() must return -EPROBE_DEFER
if acpi_dev_gpio_irq_get_by() returns the same.
Fixes: 6c2a6ddca7 ("net: mellanox: mlxbf_gige: Replace non-standard interrupt handling")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250618135902.346-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e353b0854d ]
Before calling lan743x_ptp_io_event_clock_get(), the 'channel' value
is checked against the maximum value of PCI11X1X_PTP_IO_MAX_CHANNELS(8).
This seems correct and aligns with the PTP interrupt status register
(PTP_INT_STS) specifications.
However, lan743x_ptp_io_event_clock_get() writes to ptp->extts[] with
only LAN743X_PTP_N_EXTTS(4) elements, using channel as an index:
lan743x_ptp_io_event_clock_get(..., u8 channel,...)
{
...
/* Update Local timestamp */
extts = &ptp->extts[channel];
extts->ts.tv_sec = sec;
...
}
To avoid an out-of-bounds write and utilize all the supported GPIO
inputs, set LAN743X_PTP_N_EXTTS to 8.
Detected using the static analysis tool - Svace.
Fixes: 60942c397a ("net: lan743x: Add support for PTP-IO Event Input External Timestamp (extts)")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://patch.msgid.link/20250616113743.36284-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bd1bafd44 ]
The semantics are that caller of fbnic_mbx_map_msg() retains
the ownership of the message on error. All existing callers
dutifully free the page.
Fixes: da3cde0820 ("eth: fbnic: Add FW communication mechanism")
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250616195510.225819-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dacc94c6f ]
The commit under the Fixes tag below which updates the VNICs' RSS
and MRU during .ndo_queue_start(), needs to be extended to cover any
non-default RSS contexts which have their own VNICs. Without this
step, packets that are destined to a non-default RSS context may be
dropped after .ndo_queue_start().
We further optimize this scheme by updating the VNIC only if the
RX ring being restarted is in the RSS table of the VNIC. Updating
the VNIC (in particular setting the MRU to 0) will momentarily stop
all traffic to all rings in the RSS table. Any VNIC that has the
RX ring excluded from the RSS table can skip this step and avoid the
traffic disruption.
Note that this scheme is just an improvement. A VNIC with multiple
rings in the RSS table will still see traffic disruptions to all rings
in the RSS table when one of the rings is being restarted. We are
working on a FW scheme that will improve upon this further.
Fixes: 5ac066b7b0 ("bnxt_en: Fix queue start to update vnic RSS table")
Reported-by: David Wei <dw@davidwei.uk>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250613231841.377988-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e11baaea94 ]
Add a new helper function that will configure MRU and RSS table
of a VNIC. This will be useful when we configure both on a VNIC
when resetting an RX ring. This function will be used again in
the next bug fix patch where we have to reconfigure VNICs for RSS
contexts.
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Wei <dw@davidwei.uk>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250613231841.377988-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 5dacc94c6f ("bnxt_en: Update MRU and RSS table of RSS contexts on queue reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 919f9f497d ]
The bnxt_queue_{start | stop}() access vnic_info as much as allocated,
which indicates bp->nr_vnics.
So, it should not reach bp->vnic_info[bp->nr_vnics].
Fixes: 661958552e ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250316025837.939527-1-ap420073@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 5dacc94c6f ("bnxt_en: Update MRU and RSS table of RSS contexts on queue reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 688a0d61b2 ]
On some systems with Nahum 11 and Nahum 13 the value of the XTAL clock in
the software STRAP is incorrect. This causes the PTP timer to run at the
wrong rate and can lead to synchronization issues.
The STRAP value is configured by the system firmware, and a firmware
update is not always possible. Since the XTAL clock on these systems
always runs at 38.4MHz, the driver may ignore the STRAP and just set
the correct value.
Fixes: cc23f4f0b6 ("e1000e: Add support for Meteor Lake")
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Reviewed-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d3bc9e5e7 ]
This patch fixes an issue seen in a large-scale deployment under heavy
incoming pkts where the aRFS flow wrongly matches a flow and reprograms the
NIC with wrong settings. That mis-steering causes RX-path latency spikes
and noisy neighbor effects when many connections collide on the same
hash (some of our production servers have 20-30K connections).
set_rps_cpu() calls ndo_rx_flow_steer() with flow_id that is calculated by
hashing the skb sized by the per rx-queue table size. This results in
multiple connections (even across different rx-queues) getting the same
hash value. The driver steer function modifies the wrong flow to use this
rx-queue, e.g.: Flow#1 is first added:
Flow#1: <ip1, port1, ip2, port2>, Hash 'h', q#10
Later when a new flow needs to be added:
Flow#2: <ip3, port3, ip4, port4>, Hash 'h', q#20
The driver finds the hash 'h' from Flow#1 and updates it to use q#20. This
results in both flows getting un-optimized - packets for Flow#1 goes to
q#20, and then reprogrammed back to q#10 later and so on; and Flow #2
programming is never done as Flow#1 is matched first for all misses. Many
flows may wrongly share the same hash and reprogram rules of the original
flow each with their own q#.
Tested on two 144-core servers with 16K netperf sessions for 180s. Netperf
clients are pinned to cores 0-71 sequentially (so that wrong packets on q#s
72-143 can be measured). IRQs are set 1:1 for queues -> CPUs, enable XPS,
enable aRFS (global value is 144 * rps_flow_cnt).
Test notes about results from ice_rx_flow_steer():
---------------------------------------------------
1. "Skip:" counter increments here:
if (fltr_info->q_index == rxq_idx ||
arfs_entry->fltr_state != ICE_ARFS_ACTIVE)
goto out;
2. "Add:" counter increments here:
ret = arfs_entry->fltr_info.fltr_id;
INIT_HLIST_NODE(&arfs_entry->list_entry);
3. "Update:" counter increments here:
/* update the queue to forward to on an already existing flow */
Runtime comparison: original code vs with the patch for different
rps_flow_cnt values.
+-------------------------------+--------------+--------------+
| rps_flow_cnt | 512 | 2048 |
+-------------------------------+--------------+--------------+
| Ratio of Pkts on Good:Bad q's | 214 vs 822K | 1.1M vs 980K |
| Avoid wrong aRFS programming | 0 vs 310K | 0 vs 30K |
| CPU User | 216 vs 183 | 216 vs 206 |
| CPU System | 1441 vs 1171 | 1447 vs 1320 |
| CPU Softirq | 1245 vs 920 | 1238 vs 961 |
| CPU Total | 29 vs 22.7 | 29 vs 24.9 |
| aRFS Update | 533K vs 59 | 521K vs 32 |
| aRFS Skip | 82M vs 77M | 7.2M vs 4.5M |
+-------------------------------+--------------+--------------+
A separate TCP_STREAM and TCP_RR with 1,4,8,16,64,128,256,512 connections
showed no performance degradation.
Some points on the patch/aRFS behavior:
1. Enabling full tuple matching ensures flows are always correctly matched,
even with smaller hash sizes.
2. 5-6% drop in CPU utilization as the packets arrive at the correct CPUs
and fewer calls to driver for programming on misses.
3. Larger hash tables reduces mis-steering due to more unique flow hashes,
but still has clashes. However, with larger per-device rps_flow_cnt, old
flows take more time to expire and new aRFS flows cannot be added if h/w
limits are reached (rps_may_expire_flow() succeeds when 10*rps_flow_cnt
pkts have been processed by this cpu that are not part of the flow).
Fixes: 28bf26724f ("ice: Implement aRFS")
Signed-off-by: Krishna Kumar <krikku@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5466491c9e ]
Some stress/negative firmware testing around devcmd(s) returning
EAGAIN found that the done bit could get out of sync in the
firmware when it wasn't cleared in a retry case.
While here, change the type of the local done variable to a bool
to match the return type from ionic_dev_cmd_done().
Fixes: ec8ee71473 ("ionic: stretch heartbeat detection")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250609212827.53842-1-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b43b1e2c52 upstream.
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath12k_pci_msi_alloc(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ.
This may end up with a warning from the IRQ core that is expecting the
affinity hint to be cleared before freeing the IRQ:
kernel/irq/manage.c:
/* make sure affinity_hint is cleaned up */
if (WARN_ON_ONCE(desc->affinity_hint))
desc->affinity_hint = NULL;
So to fix this issue, clear the IRQ affinity hint before calling
ath12k_pci_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm.
Fixes: a3012f206d ("wifi: ath12k: set IRQ affinity to CPU0 in case of one MSI vector")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250225053447.16824-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Wenshan Lan <jetlan9@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0948981201 upstream.
The newer firmware, lik RTL8852C version 0.27.111.0, will notify driver
report of TAS (Time Averaged SAR) power by new C2H events. This is to
assist in higher accurate calculation of TAS.
For now, driver doesn't use the report yet, so add a dummy handler to
avoid it throws info like:
rtw89_8852ce 0000:03:00.0: c2h class 9 func 6 not support
Also add "MAC" and "PHY" to the message to disambiguate the source of
C2H event.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241209042127.21424-1-pkshih@realtek.com
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6991a975e4 ]
Replicate some sanity checks that firmware does, since hardware steering
does not go through firmware.
When creating a definer, disallow matching on IP addresses without also
matching on IP version. The latter can be satisfied by matching either
on the version field in the IP header, or on the ethertype field.
Also refuse to match IPv4 IHL alongside IPv6.
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250422092540.182091-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1b01e46a3 ]
Currently, for 160 MHz bandwidth, center frequency1 and
center frequency2 are not passed correctly to the firmware.
Set center frequency1 as the center frequency
of the primary 80 MHz channel segment and center frequency2 as
the center frequency of the 160 MHz channel and pass the values
to the firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Suraj P Kizhakkethil <quic_surapk@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250304095315.3050325-2-quic_surapk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60031d9c35 ]
In the current ath12k implementation, the CE addresses
CE_HOST_IE_ADDRESS and CE_HOST_IE_2_ADDRESS are incorrect. These
values were inherited from ath11k, but ath12k does not currently use
them.
However, the Ath12k AHB support relies on these addresses. Therefore,
correct the CE addresses for ath12k.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-2-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2826139f92 ]
Currently, the link_valid field is not initialized in the monitor Rx path.
This can result in random values for the link_valid and link_id leads to
undefined behaviour in mac80211. Therefore, initialize the link_valid
field in the monitor Rx path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce8669a270 ]
To handle the Lenovo unexpected wakeup issue [1], previously we revert
commit 166a490f59 ("wifi: ath11k: support hibernation"). So currently
WLAN target is put into WoWLAN mode during suspend. This is a temporary
solution as it does not work on machines where WLAN power is cut off.
The thought here is that we do WoWLAN suspend on Lenovo machines while
do non-WoWLAN suspend (which is done in the reverted commit) on other
machines. This requires us to identify Lenovo machines from others.
For that purpose, read board vendor and product name from DMI interface,
match it against all known affected machines. If there is a match, choose
WoWLAN suspend mode, else choose non-WoWLAN mode. Save the mode in ab
for later reference.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=219196
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-1-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c056ec6dd ]
The cn10k_free_matchall_ipolicer() calls the cn10k_map_unmap_rq_policer()
for each queue in a for loop without checking for any errors.
Check the return value of the cn10k_map_unmap_rq_policer() function during
each loop, and report a warning if the function fails.
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250408032602.2909-1-vulab@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a07e3af49 ]
It is desireable to push the hardware accelerator to also
process non-segmented TCP frames: we pass the skb->len
to the "TOE/TSO" offloader and it will handle them.
Without this quirk the driver becomes unstable and lock
up and and crash.
I do not know exactly why, but it is probably due to the
TOE (TCP offload engine) feature that is coupled with the
segmentation feature - it is not possible to turn one
part off and not the other, either both TOE and TSO are
active, or neither of them.
Not having the TOE part active seems detrimental, as if
that hardware feature is not really supposed to be turned
off.
The datasheet says:
"Based on packet parsing and TCP connection/NAT table
lookup results, the NetEngine puts the packets
belonging to the same TCP connection to the same queue
for the software to process. The NetEngine puts
incoming packets to the buffer or series of buffers
for a jumbo packet. With this hardware acceleration,
IP/TCP header parsing, checksum validation and
connection lookup are offloaded from the software
processing."
After numerous tests with the hardware locking up after
something between minutes and hours depending on load
using iperf3 I have concluded this is necessary to stabilize
the hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20250408-gemini-ethernet-tso-always-v1-1-e669f932359c@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4145f00227 ]
ASIX AX88772B based USB 10/100 Ethernet adapter doesn't come
up ("carrier off"), despite the built-in 100BASE-FX PHY positive link
indication. The internal PHY is configured (using EEPROM) in fixed
100 Mbps full duplex mode.
The primary problem appears to be using carrier_netif_{on,off}() while,
at the same time, delegating carrier management to phylink. Use only the
latter and remove "manual control" in the asix driver.
I don't have any other AX88772 board here, but the problem doesn't seem
specific to a particular board or settings - it's probably
timing-dependent.
Remove unused asix_adjust_link() as well.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/m3plhmdfte.fsf_-_@t19.piap.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a808691df3 ]
In case the rule already exists and another VSI wants to subscribe to it
new VSI list is being created and both VSIs are moved to it.
Currently, the check for already existing VSI with the same rule is done
based on fdw_id.hw_vsi_id, which applies only to LOOKUP_RX flag.
Change it to vsi_handle. This is software VSI ID, but it can be applied
here, because vsi_map itself is also based on it.
Additionally change return status in case the VSI already exists in the
VSI map to "Already exists". Such case should be handled by the caller.
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdcb3804ee ]
The current implementation of `ixgbe_write_i2c_combined_generic_int` and
`ixgbe_write_i2c_byte_generic_int` sets `max_retry` to `1`, which makes
the condition `retry < max_retry` always evaluate to `false`. This renders
the retry mechanism ineffective, as the debug message and retry logic are
never executed.
This patch increases `max_retry` to `3` in both functions, aligning them
with the retry logic in `ixgbe_read_i2c_combined_generic_int`. This
ensures that the retry mechanism functions as intended, improving
robustness in case of I2C write failures.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015bac5dac ]
When the device sends a specific input, an integer underflow can occur, leading
to MMIO write access to an invalid page.
Prevent the integer underflow by changing the type of related variables.
Signed-off-by: Kyungwook Boo <bookyungwook@gmail.com>
Link: https://lore.kernel.org/lkml/ffc91764-1142-4ba2-91b6-8c773f6f7095@gmail.com/T/
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce7aec6b1 ]
With hardware grouping, during reboot, whenever a device is removed, it
powers down itself and all its partner devices in the same group. Now this
is done by all devices and hence there is multiple power down for devices
and hence the following error messages can be seen:
ath12k_pci 0002:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0002:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0003:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0003:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0004:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0004:01:00.0: failed to set mhi state: POWER_OFF(3)
To prevent this, check if the ATH12K_PCI_FLAG_INIT_DONE flag is already
set before powering down. If it is set, it indicates that another partner
device has already performed the power down, and this device can skip this
step.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-3-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09737cb80b ]
of_get_mac_address() might fetch the MAC address from NVMEM and that
driver might not have been loaded. In that case, -EPROBE_DEFER is
returned. Right now, this will trigger an immediate fallback to
am65_cpsw_am654_get_efuse_macid() possibly resulting in a random MAC
address although the MAC address is stored in the referenced NVMEM.
Fix it by handling the -EPROBE_DEFER return code correctly. This also
means that the creation of the MDIO device has to be moved to a later
stage as -EPROBE_DEFER must not be returned after child devices are
created.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250414084336.4017237-3-mwalle@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb7433cc5c ]
Currently, the RX multicast broadcast packet check is performed using
bit 15 from the info6 field of the MPDU start descriptor. This check
can also be done using bit 9 from the info5 field of the MSDU end
descriptor. However, in some scenarios multicast bit is not set when
fetched from MPDU start descriptor.
Therefore, checking the RX multicast broadcast packet from the MSDU
end descriptor is more reliable as it is per MSDU.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411061523.859387-2-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bccacb4cc ]
The "ref_count" field in struct bnxt_ulp is unused after
commit a43c26fa2e ("RDMA/bnxt_re: Remove the sriov config callback").
So we can just remove it now.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250417172448.1206107-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20c76dadc7 ]
FDB entries are allocated in an atomic context as they can be added from
the data path when learning is enabled.
After converting the FDB hash table to rhashtable, the insertion rate
will be much higher (*) which will entail a much higher rate of per-CPU
allocations via dst_cache_init().
When adding a large number of entries (e.g., 256k) in a batch, a small
percentage (< 0.02%) of these per-CPU allocations will fail [1]. This
does not happen with the current code since the insertion rate is low
enough to give the per-CPU allocator a chance to asynchronously create
new chunks of per-CPU memory.
Given that:
a. Only a small percentage of these per-CPU allocations fail.
b. The scenario where this happens might not be the most realistic one.
c. The driver can work correctly without dst caches. The dst_cache_*()
APIs first check that the dst cache was properly initialized.
d. The dst caches are not always used (e.g., 'tos inherit').
It seems reasonable to not treat these allocation failures as fatal.
Therefore, do not bail when dst_cache_init() fails and suppress warnings
by specifying '__GFP_NOWARN'.
[1] percpu: allocation failed, size=40 align=8 atomic=1, atomic alloc failed, no space left
(*) 97% reduction in average latency of vxlan_fdb_update() when adding
256k entries in a batch.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250415121143.345227-14-idosch@nvidia.com
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f2f8d8b68 ]
Unify the check for IP version when creating a definer. A given matcher
is deemed to match on IPv6 if any of the higher order (>31) bits of
source or destination address mask are set.
A single packet cannot mix IP versions between source and destination
addresses, so it makes no sense that they would be decided on
independently.
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250422092540.182091-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f71c549b26 ]
Previously, nsim_rcv was not marking the NAPI ID on the skb, leading to
applications seeing a napi ID of 0 when using SO_INCOMING_NAPI_ID.
To add to the userland confusion, netlink appears to correctly report
the NAPI IDs for netdevsim queues but the resulting file descriptor from
a call to accept() was reporting a NAPI ID of 0.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250424002746.16891-2-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20aac091a1 ]
An incorrect Voltage Controlled Oscillator (VCO) setting
may cause Synthesizer (SYN) unlock, which may lead to a
failure in the TX authentication request.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250416081241.36138-3-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cc2c48c4a ]
rxq->read is accessed without the rxq->lock in a few places,
Make sure to have the lock there.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250424153620.73725f207aaa.I1a3e4b6c5fd370e029fdacfcdc9ee335788afa98@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ecf56f4b6 ]
The MSE102x doesn't provide any interrupt register, so the only way
to handle the level interrupt is to fetch the whole packet from
the MSE102x internal buffer via SPI. So in cases the interrupt
handler fails to do this, it should return IRQ_NONE. This allows
the core to disable the interrupt in case the issue persists
and prevent an interrupt storm.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20250509120435.43646-6-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b86bcfee30 ]
As mlx4 has implemented skb_tx_timestamp() in mlx4_en_xmit(), the
SOFTWARE flag is surely needed when users are trying to get timestamp
information.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250510093442.79711-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33d4cc81fc ]
Make sure the call of skb_tx_timestamp is as close as possbile to the
doorbell.
The patch also adjusts the order of setting SKBTX_IN_PROGRESS and
generate software timestamp so that without SOF_TIMESTAMPING_OPT_TX_SWHW
being set the software and hardware timestamps will not appear in the
error queue of socket nearly at the same time (Please see __skb_tstamp_tx()).
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Link: https://patch.msgid.link/20250510134812.48199-4-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285ad74775 ]
Make sure the call of skb_tx_timestamp is as close as possible to the
doorbell.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Link: https://patch.msgid.link/20250510134812.48199-2-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d105652b33 ]
Due to mac80211 triggering the hardware to enter idle mode, it fails
to install WEP key causing connected station can't ping successfully.
Currently, it forces the hardware to leave idle mode before driver
adding WEP keys.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250507031203.8256-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd2e7bae92 ]
Firmware requests 2 segments at first. The first segment is of 6799360
whose allocation fails due to dma remapping not available. The success
is returned to firmware. Then firmware asks for 22 smaller segments
instead of 2 big ones. Those get allocated successfully. At suspend/
hibernation time, these segments aren't freed as they will be reused
by firmware after resuming.
After resuming, the firmware asks for the 2 segments again with the
first segment of 6799360 size. Since chunk->vaddr is not NULL, the
type and size are compared with the previous type and size to know if
it can be reused or not. Unfortunately, it is detected that it cannot
be reused and this first smaller segment is freed. Then we continue to
allocate 6799360 size memory which fails and ath11k_qmi_free_target_mem_chunk()
is called which frees the second smaller segment as well. Later success
is returned to firmware which asks for 22 smaller segments again. But
as we had freed 2 segments already, we'll allocate the first 2 new
smaller segments again and reuse the remaining 20. Hence 20 small
segments are being reused instead of 22.
Add skip logic when vaddr is set, but size/type don't match. Use the
same skip and success logic as used when dma_alloc_coherent() fails.
By skipping, the possibility of resume failure due to kernel failing to
allocate memory for QMI can be avoided.
kernel: ath11k_pci 0000:03:00.0: failed to allocate dma memory for qmi (524288 B type 1)
ath11k_pci 0000:03:00.0: failed to allocate qmi target memory: -22
Tested-on: WCN6855 WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.6
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250428080242.466901-1-usama.anjum@collabora.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef115c265a ]
spin_lock/spin_unlock are used in ath12k_reg_chan_list_event
to acquire/release ab->base_lock. For now this is safe because
that function is only called in soft IRQ context.
But ath12k_reg_chan_list_event() will be called from process
context in an upcoming patch, and this can result in a deadlock
if ab->base_lock is acquired in process context and then soft
IRQ occurs on the same CPU and tries to acquire that lock.
Fix it by using spin_lock_bh and spin_unlock_bh instead.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-1-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a69bbf89d7 ]
Currently, HAL_RX_MSDU_PKT_LENGTH_GET uses u32_get_bits to obtain the
MSDU length from the MSDU description.
This is not right. Because all halphy descriptions are little endian.
So use le32_get_bits for HAL_RX_MSDU_PKT_LENGTH_GET.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-9-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12889ce926 ]
This patch synchronizes code that accesses from both user-space
and IRQ contexts. The `get_stats()` function can be called from both
context.
`dev->stats.tx_errors` and `dev->stats.collisions` are also updated
in the `tx_errors()` function. Therefore, these fields must also be
protected by synchronized.
There is no code that accessses `dev->stats.tx_errors` between the
previous and updated lines, so the updating point can be moved.
Signed-off-by: Moon Yeounsu <yyyynoom@gmail.com>
Link: https://patch.msgid.link/20250515075333.48290-1-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d81e893b4 ]
Add thermal protection to prevent the chip from possible overheating
due to prolonged high traffic and adverse operating conditions.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Link: https://patch.msgid.link/20250509082117.453819-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7011faebe5 ]
This allows mt7922 in hostapd mode to transmit up to 1.4 Gbps.
Signed-off-by: Samuel Williams <sam8641@gmail.com>
Link: https://patch.msgid.link/20250511005316.1118961-1-sam8641@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c0e4f606d ]
Adds support for:
- LiteOn WN4516R
- LiteOn WN4519R
Both use:
- A nonstandard USB connector
- Mediatek chipset MT7600U
- ASIC revision: 76320044
Disabled VHT support on ASIC revision 76320044:
This fixes the 5G connectibity issue on LiteOn WN4519R module
see https://github.com/openwrt/mt76/issues/971
And may also fix the 5G issues on the XBox One Wireless Adapter
see https://github.com/openwrt/mt76/issues/200
I have looked at the FCC info related to the MT7632U chip as mentioned in here:
https://github.com/openwrt/mt76/issues/459
These confirm the chipset does not support 'ac' mode and hence VHT should be turned of.
Signed-off-by: Henk Vergonet <henk.vergonet@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250418143914.31384-1-henk.vergonet@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
