commit 566c2d8388 upstream.
Depending on the SoC where the FEC is integrated into the PPS channel
might be routed to different timer instances. Make this configurable
from the devicetree.
When the related DT property is not present fallback to the previous
default and use channel 0.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Csókás, Bence <csokas.bence@prolan.hu>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 378e8feea9 upstream.
The DP83869 PHY transceiver supports converting from RGMII to 1000base-x.
In this operation mode, autonegotiation can be performed, as described in
IEEE802.3.
The DP83869 has a set of fiber-specific registers located at offset 0xc00.
When the transceiver is configured in RGMII-to-1000base-x mode, these
registers are mapped onto offset 0, which should make reading the
autonegotiation status transparent.
However, the fiber registers at offset 0xc04 and 0xc05 follow the bit
layout specified in Clause 37, and genphy_read_status() assumes a Clause 22
layout. Thus, genphy_read_status() doesn't properly read the capabilities
advertised by the link partner, resulting in incorrect link parameters.
Similarly, genphy_config_aneg() doesn't properly write advertised
capabilities.
Fix the 1000base-x autonegotiation procedure by replacing
genphy_read_status() and genphy_config_aneg() with their Clause 37
equivalents.
Fixes: a29de52ba2 ("net: dp83869: Add ability to advertise Fiber connection")
Cc: stable@vger.kernel.org
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Link: https://patch.msgid.link/20241112-dp83869-1000base-x-v3-1-36005f4ab0d9@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83134ef460 upstream.
Jordan reported that when running Cilium with netkit in per-endpoint-routes
mode, network policy misclassifies traffic. In this direct routing mode
of Cilium which is used in case of GKE/EKS/AKS, the Pod's BPF program to
enforce policy sits on the netkit primary device's egress side.
The issue here is that in case of netkit's netkit_prep_forward(), it will
clear meta data such as skb->mark and skb->priority before executing the
BPF program. Thus, identity data stored in there from earlier BPF programs
(e.g. from tcx ingress on the physical device) gets cleared instead of
being made available for the primary's program to process. While for traffic
egressing the Pod via the peer device this might be desired, this is
different for the primary one where compared to tcx egress on the host
veth this information would be available.
To address this, add a new parameter for the device orchestration to
allow control of skb->mark and skb->priority scrubbing, to make the two
accessible from BPF (and eventually leave it up to the program to scrub).
By default, the current behavior is retained. For netkit peer this also
enables the use case where applications could cooperate/signal intent to
the BPF program.
Note that struct netkit has a 4 byte hole between policy and bundle which
is used here, in other words, struct netkit's first cacheline content used
in fast-path does not get moved around.
Fixes: 35dfaad718 ("netkit, bpf: Add bpf programmable net device")
Reported-by: Jordan Rife <jrife@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://github.com/cilium/cilium/issues/34042
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20241004101335.117711-1-daniel@iogearbox.net
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea301aec8b upstream.
After assembling the new private flags on a PF, the operation to determine
the changed flags uses the wrong bitmaps. Instead of xor-ing orig_flags
with new_flags, it uses the still unchanged pf->flags, thus changed_flags
is always 0.
Fix it by using the correct bitmaps.
The issue was discovered while debugging why disabling source pruning
stopped working with release 6.7. Although the new flags will be copied to
pf->flags later on in that function, disabling source pruning requires
a reset of the PF, which was skipped due to this bug.
Disabling source pruning:
$ sudo ethtool --set-priv-flags eno1 disable-source-pruning on
$ sudo ethtool --show-priv-flags eno1
Private flags for eno1:
MFP : off
total-port-shutdown : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
link-down-on-close : off
legacy-rx : off
disable-source-pruning: on
disable-fw-lldp : off
rs-fec : off
base-r-fec : off
vf-vlan-pruning : off
Regarding reproducing:
I observed the issue with a rather complicated lab setup, where
* two VLAN interfaces are created on eno1
* each with a different MAC address assigned
* each moved into a separate namespace
* both VLANs are bridged externally, so they form a single layer 2 network
The external bridge is done via a channel emulator adding packet loss and
delay and the application in the namespaces tries to send/receive traffic
and measure the performance. Sender and receiver are separated by
namespaces, yet the network card "sees its own traffic" send back to it.
To make that work, source pruning has to be disabled.
Cc: stable@vger.kernel.org
Fixes: 70756d0a47 ("i40e: Use DECLARE_BITMAP for flags and hw_features fields in i40e_pf")
Signed-off-by: Peter Große <pegro@friiks.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20241113210705.1296408-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ffade77b6 upstream.
When configuring flow steering rules, the driver is currently going
through a reset for all errors from the device. Instead, the driver
should only reset when there's a timeout error from the device.
Fixes: 57718b60df ("gve: Add flow steering adminq commands")
Cc: stable@vger.kernel.org
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241113175930.2585680-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e19a3b590 upstream.
The fixed patch introduced an additional condition to enter the scope
where the 'root' device_node is released (!settings->board_type,
currently 'err'), which avoid decrementing the refcount with a call to
of_node_put() if that second condition is not satisfied.
Move the call to of_node_put() to the point where 'root' is no longer
required to avoid leaking the resource if err is not zero.
Cc: stable@vger.kernel.org
Fixes: 7682de8b33 ("wifi: brcmfmac: of: Fetch Apple properties")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241030-brcmfmac-of-cleanup-v1-1-0b90eefb4279@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1304446f67 upstream.
If there is an error during some initialization related to firmware,
the function ath12k_dp_cc_cleanup is called to release resources.
However this is released again when the device is unbinded (ath12k_pci),
and we get:
BUG: kernel NULL pointer dereference, address: 0000000000000020
at RIP: 0010:ath12k_dp_cc_cleanup.part.0+0xb6/0x500 [ath12k]
Call Trace:
ath12k_dp_cc_cleanup
ath12k_dp_free
ath12k_core_deinit
ath12k_pci_remove
...
The issue is always reproducible from a VM because the MSI addressing
initialization is failing.
In order to fix the issue, just set to NULL the released structure in
ath12k_dp_cc_cleanup at the end.
cc: stable@vger.kernel.org
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://patch.msgid.link/20241017181004.199589-2-jtornosm@redhat.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c1b544563 upstream.
Syzkaller reported a hung task with uevent_show() on stack trace. That
specific issue was addressed by another commit [0], but even with that
fix applied (for example, running v6.12-rc5) we face another type of hung
task that comes from the same reproducer [1]. By investigating that, we
could narrow it to the following path:
(a) Syzkaller emulates a Realtek USB WiFi adapter using raw-gadget and
dummy_hcd infrastructure.
(b) During the probe of rtl8192cu, the driver ends-up performing an efuse
read procedure (which is related to EEPROM load IIUC), and here lies the
issue: the function read_efuse() calls read_efuse_byte() many times, as
loop iterations depending on the efuse size (in our example, 512 in total).
This procedure for reading efuse bytes relies in a loop that performs an
I/O read up to *10k* times in case of failures. We measured the time of
the loop inside read_efuse_byte() alone, and in this reproducer (which
involves the dummy_hcd emulation layer), it takes 15 seconds each. As a
consequence, we have the driver stuck in its probe routine for big time,
exposing a stack trace like below if we attempt to reboot the system, for
example:
task:kworker/0:3 state:D stack:0 pid:662 tgid:662 ppid:2 flags:0x00004000
Workqueue: usb_hub_wq hub_event
Call Trace:
__schedule+0xe22/0xeb6
schedule_timeout+0xe7/0x132
__wait_for_common+0xb5/0x12e
usb_start_wait_urb+0xc5/0x1ef
? usb_alloc_urb+0x95/0xa4
usb_control_msg+0xff/0x184
_usbctrl_vendorreq_sync+0xa0/0x161
_usb_read_sync+0xb3/0xc5
read_efuse_byte+0x13c/0x146
read_efuse+0x351/0x5f0
efuse_read_all_map+0x42/0x52
rtl_efuse_shadow_map_update+0x60/0xef
rtl_get_hwinfo+0x5d/0x1c2
rtl92cu_read_eeprom_info+0x10a/0x8d5
? rtl92c_read_chip_version+0x14f/0x17e
rtl_usb_probe+0x323/0x851
usb_probe_interface+0x278/0x34b
really_probe+0x202/0x4a4
__driver_probe_device+0x166/0x1b2
driver_probe_device+0x2f/0xd8
[...]
We propose hereby to drastically reduce the attempts of doing the I/O
reads in case of failures, restricted to USB devices (given that
they're inherently slower than PCIe ones). By retrying up to 10 times
(instead of 10000), we got reponsiveness in the reproducer, while seems
reasonable to believe that there's no sane USB device implementation in
the field requiring this amount of retries at every I/O read in order
to properly work. Based on that assumption, it'd be good to have it
backported to stable but maybe not since driver implementation (the 10k
number comes from day 0), perhaps up to 6.x series makes sense.
[0] Commit 15fffc6a56 ("driver core: Fix uevent_show() vs driver detach race")
[1] A note about that: this syzkaller report presents multiple reproducers
that differs by the type of emulated USB device. For this specific case,
check the entry from 2024/08/08 06:23 in the list of crashes; the C repro
is available at https://syzkaller.appspot.com/text?tag=ReproC&x=1521fc83980000.
Cc: stable@vger.kernel.org # v6.1+
Reported-by: syzbot+edd9fe0d3a65b14588d5@syzkaller.appspotmail.com
Tested-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241101193412.1390391-1-gpiccoli@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca68ce0d9f upstream.
If there is an error during some initialization related to firmware,
the buffers dp->tx_ring[i].tx_status are released.
However this is released again when the device is unbinded (ath12k_pci),
and we get:
WARNING: CPU: 0 PID: 2098 at mm/slub.c:4689 free_large_kmalloc+0x4d/0x80
Call Trace:
free_large_kmalloc
ath12k_dp_free
ath12k_core_deinit
ath12k_pci_remove
...
The issue is always reproducible from a VM because the MSI addressing
initialization is failing.
In order to fix the issue, just set the buffers to NULL after releasing in
order to avoid the double free.
cc: stable@vger.kernel.org
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://patch.msgid.link/20241017181004.199589-3-jtornosm@redhat.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3661c05c54 ]
If we go through the PCI shutdown or suspend path, we shutdown the
NIC but PTP remains registered. If the kernel continues to run for
a little bit, the periodic PTP .do_aux_work() function may be called
and it will read the PHC from the BAR register. Since the device
has already been disabled, it will cause a PCIe completion timeout.
Fix it by calling bnxt_ptp_clear() in the PCI shutdown/suspend
handlers. bnxt_ptp_clear() will unregister from PTP and
.do_aux_work() will be canceled.
In bnxt_resume(), we need to re-initialize PTP.
Fixes: a521c8a01d ("bnxt_en: Move bnxt_ptp_init() from bnxt_open() back to bnxt_init_one()")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e9614cd95 ]
Instead of passing the 2nd parameter phc_cfg to bnxt_ptp_init().
Store it in bp->ptp_cfg so that the caller doesn't need to know what
the value should be.
In the next patch, we'll need to call bnxt_ptp_init() in bnxt_resume()
and this will make it easier.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 3661c05c54 ("bnxt_en: Unregister PTP during PCI shutdown and suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3051a77a09 ]
The MTU setting at the time an XDP multi-buffer is attached
determines whether the aggregation ring will be used and the
rx_skb_func handler. This is done in bnxt_set_rx_skb_mode().
If the MTU is later changed, the aggregation ring setting may need
to be changed and it may become out-of-sync with the settings
initially done in bnxt_set_rx_skb_mode(). This may result in
random memory corruption and crashes as the HW may DMA data larger
than the allocated buffer size, such as:
BUG: kernel NULL pointer dereference, address: 00000000000003c0
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 17 PID: 0 Comm: swapper/17 Kdump: loaded Tainted: G S OE 6.1.0-226bf9805506 #1
Hardware name: Wiwynn Delta Lake PVT BZA.02601.0150/Delta Lake-Class1, BIOS F0E_3A12 08/26/2021
RIP: 0010:bnxt_rx_pkt+0xe97/0x1ae0 [bnxt_en]
Code: 8b 95 70 ff ff ff 4c 8b 9d 48 ff ff ff 66 41 89 87 b4 00 00 00 e9 0b f7 ff ff 0f b7 43 0a 49 8b 95 a8 04 00 00 25 ff 0f 00 00 <0f> b7 14 42 48 c1 e2 06 49 03 95 a0 04 00 00 0f b6 42 33f
RSP: 0018:ffffa19f40cc0d18 EFLAGS: 00010202
RAX: 00000000000001e0 RBX: ffff8e2c805c6100 RCX: 00000000000007ff
RDX: 0000000000000000 RSI: ffff8e2c271ab990 RDI: ffff8e2c84f12380
RBP: ffffa19f40cc0e48 R08: 000000000001000d R09: 974ea2fcddfa4cbf
R10: 0000000000000000 R11: ffffa19f40cc0ff8 R12: ffff8e2c94b58980
R13: ffff8e2c952d6600 R14: 0000000000000016 R15: ffff8e2c271ab990
FS: 0000000000000000(0000) GS:ffff8e3b3f840000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000003c0 CR3: 0000000e8580a004 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<IRQ>
__bnxt_poll_work+0x1c2/0x3e0 [bnxt_en]
To address the issue, we now call bnxt_set_rx_skb_mode() within
bnxt_change_mtu() to properly set the AGG rings configuration and
update rx_skb_func based on the new MTU value.
Additionally, BNXT_FLAG_NO_AGG_RINGS is cleared at the beginning of
bnxt_set_rx_skb_mode() to make sure it gets set or cleared based on
the current MTU.
Fixes: 08450ea98a ("bnxt_en: Fix max_mtu setting for multi-buf XDP")
Co-developed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ac066b7b0 ]
HWRM_RING_FREE followed by a HWRM_RING_ALLOC is not guaranteed to
have the same FW ring ID as before. So we must reinitialize the
RSS table with the correct ring IDs. Otherwise, traffic may not
resume properly if the restarted ring ID is stale. Since this
feature is only supported on P5_PLUS chips, we call
bnxt_vnic_set_rss_p5() to update the HW RSS table.
Fixes: 2d694c27d3 ("bnxt_en: implement netdev_queue_mgmt_ops")
Cc: David Wei <dw@davidwei.uk>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5007991670 ]
Use the return value from bnxt_get_media() to determine the port and
link modes. bnxt_get_media() returns the proper BNXT_MEDIA_KR when
the PHY is backplane. This will correct the ethtool settings for
backplane devices.
Fixes: 5d4e1bf606 ("bnxt_en: extend media types to supported and autoneg modes")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5311598f7f ]
After successful PCIe AER recovery, FW will reset all resource
reservations. If it is IF_UP, the driver will call bnxt_open() and
all resources will be reserved again. It it is IF_DOWN, we should
call bnxt_reserve_rings() so that we can reserve resources including
RoCE resources to allow RoCE to resume after AER. Without this
patch, RoCE fails to resume in this IF_DOWN scenario.
Later, if it becomes IF_UP, bnxt_open() will see that resources have
been reserved and will not reserve again.
Fixes: fb1e6e562b ("bnxt_en: Fix AER recovery.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 762ca6eed0 ]
During initialization, the AF driver resets all blocks. The RPM (MAC)
block and NIX block operate on a credit-based model. When the NIX block
resets during active traffic flow, it doesn't release credits to the RPM
block. This causes the RPM FIFO to overflow, leading to receive traffic
struck.
To address this issue, the patch introduces the following changes:
1. Stop receiving traffic at the MAC level during AF driver
initialization.
2. Perform an X2P reset (prevents RXFIFO of all LMACS from pushing data)
3. Reset the NIX block.
4. Clear the X2P reset and re-enable receiving traffic.
Fixes: 54d557815e ("octeontx2-af: Reset all RVU blocks")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fc2164108 ]
The corrected words register(FCFECX_VL0_CCW_LO)/Uncorrected words
register (FCFECX_VL0_NCCW_LO) of FCFEC counter has different LMAC
offset which needs to be accessed differently.
Fixes: 84ad364211 ("octeontx2-af: Add FEC stats for RPM/RPM_USX block")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07cd1eb166 ]
The earlier patch sets the 'Stats control register' for RPM
receive/transmit statistics instead of RSFEC statistics,
causing the driver to return stale FEC counters.
Fixes: 84ad364211 ("octeontx2-af: Add FEC stats for RPM/RPM_USX block")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1e8884e05 ]
Low network performance is observed even on RPMs with larger
FIFO lengths.
The cn10kb silicon has three RPM blocks with the following
FIFO sizes:
--------------------
| RPM0 | 256KB |
| RPM1 | 256KB |
| RPM2 | 128KB |
--------------------
The current design stores the FIFO length in a common structure for all
RPMs (mac_ops). As a result, the FIFO length of the last RPM is applied
to all RPMs, leading to reduced network performance.
This patch resolved the problem by storing the fifo length in per MAC
structure (cgx).
Fixes: b9d0fedc62 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ebbbb23ea ]
Due to a bug in the previous patch, there is a mismatch
between the lmac type reported by the driver and the actual
hardware configuration.
Fixes: 3ad3f8f93c ("octeontx2-af: cn10k: MAC internal loopback support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 407618d66d ]
On DWMAC3 and later, there's a RX Watchdog interrupt that's used for
interrupt coalescing. It's known to be buggy on some platforms, and
dwmac-socfpga appears to be one of them. Changing the interrupt
coalescing from ethtool doesn't appear to have any effect here.
Without disabling RIWT (Received Interrupt Watchdog Timer, I
believe...), we observe latencies while receiving traffic that amount to
around ~0.4ms. This was discovered with NTP but can be easily reproduced
with a simple ping. Without this patch :
64 bytes from 192.168.5.2: icmp_seq=1 ttl=64 time=0.657 ms
With this patch :
64 bytes from 192.168.5.2: icmp_seq=1 ttl=64 time=0.254 ms
Fixes: 801d233b73 ("net: stmmac: Add SOCFPGA glue driver")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241122141256.764578-1-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b032ae57d4 ]
If the clock pep->clk was not enabled in pxa168_eth_probe,
it should not be disabled in any path.
Conversely, if it was enabled in pxa168_eth_probe, it must be disabled
in all error paths to ensure proper cleanup.
Use the devm_clk_get_enabled helper function to ensure proper call balance
for pep->clk.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: a49f37eed2 ("net: add Fast Ethernet driver for PXA168.")
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Link: https://patch.msgid.link/20241121200658.2203871-1-mordan@ispras.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc8d0ecdd ]
If an optional resource is found but fails to remap, return on failure.
Avoids any potential problems when using the iomapped resource as the
assumption is that it's available.
Fixes: 23a890d493 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241121193152.8966-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a01cfcfda5 ]
Previously, when the hardware version ID was determined to be invalid,
only an error message was printed without any further handling. Therefore,
this patch makes the necessary corrections to address this.
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1fc14c4df ]
Previously, the reported speed was uniformly set to SPEED_5000, but the
RTL907XD-V1 actually operates at a speed of SPEED_10000. Therefore, this
patch makes the necessary correction.
Fixes: dd7f17c40f ("rtase: Implement ethtool function")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1f8609ff1 ]
Different hardware requires different configurations, but this distinction
was not made previously. Additionally, the error message was not clear
enough. Therefore, this patch will address the issues mentioned above.
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f164b29663 ]
VCAP API unit tests fail randomly with errors such as
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:387
Expected 134 + 7 == iter.offset, but
134 + 7 == 141 (0x8d)
iter.offset == 17214 (0x433e)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:388
Expected 5 == iter.reg_idx, but
iter.reg_idx == 702 (0x2be)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:389
Expected 11 == iter.reg_bitpos, but
iter.reg_bitpos == 15 (0xf)
# vcap_api_iterator_init_test: pass:0 fail:1 skip:0 total:1
Comments in the code state that "A typegroup table ends with an all-zero
terminator". Add the missing terminators.
Some of the typegroups did have a terminator of ".offset = 0, .width = 0,
.value = 0,". Replace those terminators with "{ }" (no trailing ',') for
consistency and to excplicitly state "this is a terminator".
Fixes: 67d637516f ("net: microchip: sparx5: Adding KUNIT test for the VCAP API")
Cc: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119213202.2884639-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e863ff806f ]
Validate Wake-on-LAN (WoL) options in `lan78xx_set_wol` before calling
`usb_autopm_get_interface`. This prevents USB autopm refcounting issues
and ensures the adapter can properly enter autosuspend when invalid WoL
options are provided.
Fixes: eb9ad088f9 ("lan78xx: Check for supported Wake-on-LAN modes")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://patch.msgid.link/20241118140351.2398166-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 614f4d166e ]
The hardware on Broadcom 1G chipsets have a known limitation
where they cannot handle DMA addresses that cross over 4GB.
When such an address is encountered, the hardware sets the
address overflow error bit in the DMA status register and
triggers a reset.
However, BCM57766 hardware is setting the overflow bit and
triggering a reset in some cases when there is no actual
underlying address overflow. The hardware team analyzed the
issue and concluded that it is happening when the status
block update has an address with higher (b16 to b31) bits
as 0xffff following a previous update that had lowest bits
as 0xffff.
To work around this bug in the BCM57766 hardware, set the
coherent dma mask from the current 64b to 31b. This will
ensure that upper bits of the status block DMA address are
always at most 0x7fff, thus avoiding the improper overflow
check described above. This work around is intended for only
status block and ring memories and has no effect on TX and
RX buffers as they do not require coherent memory.
Fixes: 72f2afb8a6 ("[TG3]: Add DMA address workaround")
Reported-by: Salam Noureddine <noureddine@arista.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20241119055741.147144-1-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae7370e61c ]
Add calls to `phy_device_free` after `fixed_phy_unregister` to fix a
memory leak that occurs when the device is unplugged. This ensures
proper cleanup of pseudo fixed-link PHYs.
Fixes: 89b36fb5e5 ("lan78xx: Lan7801 Support for Fixed PHY")
Cc: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03819abbeb ]
In lan78xx_probe(), the buffer `buf` was being freed twice: once
implicitly through `usb_free_urb(dev->urb_intr)` with the
`URB_FREE_BUFFER` flag and again explicitly by `kfree(buf)`. This caused
a double free issue.
To resolve this, reordered `kmalloc()` and `usb_alloc_urb()` calls to
simplify the initialization sequence and removed the redundant
`kfree(buf)`. Now, `buf` is allocated after `usb_alloc_urb()`, ensuring
it is correctly managed by `usb_fill_int_urb()` and freed by
`usb_free_urb()` as intended.
Fixes: a6df95cae4 ("lan78xx: Fix memory allocation bug")
Cc: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bd2c61df9 ]
Fix a race condition when creating a lag bond in active backup
mode where after the bond creation the backup slave was
attached to the IB device, instead of the active slave.
This caused stale entries in the GID table, as the gid updating
mechanism relies on ib_device_get_netdev(), which would return
the backup slave.
Send an MLX5_DRIVER_EVENT_ACTIVE_BACKUP_LAG_CHANGE_LOWERSTATE
event when activating the lag, additionally to when modifying
the lag. This ensures that eventually the active netdevice is
stored in the bond IB device.
When handling this event remove the GIDs of the previously
attached netdevice in this port and rescan the GIDs of the
newly attached netdevice.
This ensures that eventually the active slave netdevice is
correctly stored in the IB device port. While there might be
a brief moment where the backup slave GIDs appear in the GID
table, it will eventually stabilize with the correct GIDs
(of the bond and the active slave).
Fixes: 8d159eb211 ("RDMA/mlx5: Use IB set_netdev and get_netdev functions")
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Link: https://patch.msgid.link/91fc2cb24f63add266a528c1c702668a80416d9f.1730381292.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2160428bcb ]
For 1000BASE-X or SGMII interface mode, the PCS also need to be selected.
Only return null pointer when there is a copper NIC with external PHY.
Fixes: 02b2a6f91b ("net: txgbe: support copper NIC with external PHY")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20241115073508.1130046-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e867ed3ac8 ]
Since the GPIO interrupt controller is always not working properly, we need
to constantly add workaround to cope with hardware deficiencies. So just
remove GPIO interrupt controller, and let the SFP driver poll the GPIO
status.
Fixes: b4a2496c17 ("net: txgbe: fix GPIO interrupt blocking")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20241115071527.1129458-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62e9c00ea8 ]
We use pcim_enable_device(), there is no need to call pci_disable_device().
Fixes: 546dd90be9 ("eth: fbnic: Add scaffolding for Meta's NIC driver")
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241115014809.754860-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1a54ec21b ]
Since we no longer shut down the device in suspend, we also no longer
call iwl_mvm_mei_device_state() and this is a problem because iwlmei
expects this to be called when it runs its own suspend sequence. It
checks mei->device_down in iwl_mei_remove() which is called upon
suspend.
Fix this by telling iwlmei when we're done accessing the device.
When we'll wake up, the device should be untouched if CSME didn't use it
during the suspend time. If CSME used it, we'll notice it through the
CSR_FUNC_SCRATCH register.
Fixes: e8bb19c1d5 ("wifi: iwlwifi: support fast resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241028135215.525287b90af2.Ibf183824471ea5580d9276d104444e53191e6900@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e53ebc7205 ]
This feature can be used on ax200 as well. It'll avoid to restart the
firmware upon suspend / resume flow. Doing so also avoids releasing and
re-allocating all the device related memory which makes the memory's
subsystem task easier.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241028135215.514efe0ce4c7.I60061277526302a75cadbba10452e94c54763f13@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: d1a54ec21b ("wifi: iwlwifi: mvm: tell iwlmei when we finished suspending")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b88a98767 ]
The wfx_core_init() returns without checking the retval from
sdio_register_driver().
If the sdio_register_driver() failed, the module failed to install,
leaving the wfx_spi_driver not unregistered.
Fixes: a7a91ca5a2 ("staging: wfx: add infrastructure for new driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241022090453.84679-1-yuancan@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f16c40acd3 ]
There might be some racing between BT and WiFi after scan. Since
one of the TX related register will be modified by both FW and
rtw89_set_channel() in driver, which could cause Tx fail. Reorder
the calling sequence to only notify coexistence mechanism after
rtw89_set_channel() is called, so that there are no concurrent
operations.
Fixes: 5f499ce69b ("wifi: rtw89: pause/proceed MCC for ROC and HW scan")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241021063219.22613-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aad0394e7a ]
The drv_priv hooked to mac80211 become as below.
(drv_priv) (instance-0)
+---------------+ +-----------+ +----------------+
| ieee80211_vif | <---> | rtw89_vif | -------> | rtw89_vif_link |
+---------------+ +-----------+ | +----------------+
|
| (instance-1)
| +----------------+
+---> | rtw89_vif_link |
+----------------+
(drv_priv) (instance-0)
+---------------+ +-----------+ +----------------+
| ieee80211_sta | <---> | rtw89_sta | -------> | rtw89_sta_link |
+---------------+ +-----------+ | +----------------+
|
| (instance-1)
| +----------------+
+---> | rtw89_sta_link |
+----------------+
The relation bewteen mac80211 link_id and our link instance is like below.
|\
(link_id) | \
0 -------- | |
1 -------- | | ------ instance-0 (link_id: X) -> work on HW band 0
2 -------- | |
... | | ------ instance-1 (link_id: Y) -> work on HW band 1
14 -------- | |
| /
|/
N.B. For cases of non-MLD connection, we set our link instance-0
active with link_id 0. So, our code flow can be compatible between
non-MLD connection and MLD connection.
Based on above, we tweak entire driver architecture first. But, we don't
dynamically enable multiple links here. That will be handled separately.
Most of the things changed here are changing flows to iterate all active
links and read bss_conf/link_sta data according to target link. And, for
cases of scan, ROC, WOW, we use instance-0 to deal with the request.
There are some things listed below, which work for now but need to extend
before multiple active links.
1. tx path
select suitable link instance among multiple active links
2. rx path
determine rx link by PPDU instead of always link instance-0
3. CAM
apply MLD pairwise key to any active links dynamically
Besides, PS code cannot easily work along with tweaking architecture. With
supporting MLO flag (currently false), we disable PS first and will fix it
by another commit in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-8-pkshih@realtek.com
Stable-dep-of: f16c40acd3 ("wifi: rtw89: Fix TX fail with A2DP after scanning")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72e9457c19 ]
Refactor STA related functions, e.g. add/assoc/disassoc/disconnect/remove
to separate most link stuffs into sub-functions for MLO reuse.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-7-pkshih@realtek.com
Stable-dep-of: f16c40acd3 ("wifi: rtw89: Fix TX fail with A2DP after scanning")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26d460e13f ]
Refactor VIF related functions, e.g. add/remove/assoc/mapping
to separate most link stuffs into sub-functions for MLO reuse.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-6-pkshih@realtek.com
Stable-dep-of: f16c40acd3 ("wifi: rtw89: Fix TX fail with A2DP after scanning")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04911c0fe8 ]
Tweak code to not always access sta->deflink directly. Instead,
according to link_id, read target link_sta from sta->link[].
For now, rtwsta_link->link_id keeps 0. When driver starts to
support MLO, the link_id will be assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-5-pkshih@realtek.com
Stable-dep-of: f16c40acd3 ("wifi: rtw89: Fix TX fail with A2DP after scanning")
Signed-off-by: Sasha Levin <sashal@kernel.org>
