[ Upstream commit 8b0587a885 ]
When port buffer headroom changes, port_update_shared_buffer()
recalculates the shared buffer size and splits it in a 3:1 ratio
(lossy:lossless) - Currently, the calculation is:
lossless = shared / 4;
lossy = (shared / 4) * 3;
Meaning, the calculation dropped the remainder of shared % 4 due to
integer division, unintentionally reducing the total shared buffer
by up to three cells on each update. Over time, this could shrink
the buffer below usable size.
Fix it by changing the calculation to:
lossless = shared / 4;
lossy = shared - lossless;
This retains all buffer cells while still approximating the
intended 3:1 split, preventing capacity loss over time.
While at it, perform headroom calculations in units of cells rather than
in bytes for more accurate calculations avoiding extra divisions.
Fixes: a440030d89 ("net/mlx5e: Update shared buffer along with device buffer changes")
Signed-off-by: Armen Ratner <armeng@nvidia.com>
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20250820133209.389065-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 451d2849ea ]
The SW currently saves local buffer ownership when setting
the buffer.
This means that the SW assumes it has ownership of the buffer
after the command is set.
If setting the buffer fails and we remain in FW ownership,
the local buffer ownership state incorrectly remains as SW-owned.
This leads to incorrect behavior in subsequent PFC commands,
causing failures.
Instead of saving local buffer ownership in SW,
query the FW for buffer ownership when setting the buffer.
This ensures that the buffer ownership state is accurately
reflected, avoiding the issues caused by incorrect ownership
states.
Fixes: ecdf2dadee ("net/mlx5e: Receive buffer support for DCBX")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-8-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2f61f1db8 ]
The port header is a general file under include, yet it
contains declarations for functions that are either not
exported or exported but not used outside the mlx5_core
driver.
To enhance code organization, we move these declarations
to mlx5_core.h, where they are more appropriately scoped.
This refactor removes unnecessary exported symbols and
prevents unexported functions from being inadvertently
referenced outside of the mlx5_core driver.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250304160620.417580-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 451d2849ea ("net/mlx5e: Query FW for buffer ownership")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc17455bc8 ]
Adjust the vport number by the base ECVF vport number so the port
attributes start at 0. Previously the port attributes would start 1
after the maximum number of host VFs.
Fixes: dc13180824 ("net/mlx5: Enable devlink port for embedded cpu VF vports")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c5d95988c ]
Octeontx2/CN10K silicon supports generating a 256-bit key per packet.
The specific fields to be extracted from a packet for key generation
are configurable via a Key Extraction (MKEX) Profile.
The AF driver scans the configured extraction profile to ensure that
fields from upper layers do not overwrite fields from lower layers in
the key.
Example Packet Field Layout:
LA: DMAC + SMAC
LB: VLAN
LC: IPv4/IPv6
LD: TCP/UDP
Valid MKEX Profile Configuration:
LA -> DMAC -> key_offset[0-5]
LC -> SIP -> key_offset[20-23]
LD -> SPORT -> key_offset[30-31]
Invalid MKEX profile configuration:
LA -> DMAC -> key_offset[0-5]
LC -> SIP -> key_offset[20-23]
LD -> SPORT -> key_offset[2-3] // Overlaps with DMAC field
In another scenario, if the MKEX profile is configured to extract
the SPI field from both AH and ESP headers at the same key offset,
the driver rejecting this configuration. In a regular traffic,
ipsec packet will be having either AH(LD) or ESP (LE). This patch
relaxes the check for the same.
Fixes: 12aa0a3b93 ("octeontx2-af: Harden rule validation.")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250820063919.1463518-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0599640a21 ]
When `lacp_active` is set to `off`, the bond operates in passive mode, meaning
it only "speaks when spoken to." However, the current kernel implementation
only sends an LACPDU in response when the partner's state changes.
As a result, once LACP negotiation succeeds, the actor stops sending LACPDUs
until the partner times out and sends an "expired" LACPDU. This causes
continuous LACP state flapping.
According to IEEE 802.1AX-2014, 6.4.13 Periodic Transmission machine. The
values of Partner_Oper_Port_State.LACP_Activity and
Actor_Oper_Port_State.LACP_Activity determine whether periodic transmissions
take place. If either or both parameters are set to Active LACP, then periodic
transmissions occur; if both are set to Passive LACP, then periodic
transmissions do not occur.
To comply with this, we remove the `!bond->params.lacp_active` check in
`ad_periodic_machine()`. Instead, we initialize the actor's port's
`LACP_STATE_LACP_ACTIVITY` state based on `lacp_active` setting.
Additionally, we avoid setting the partner's state to
`LACP_STATE_LACP_ACTIVITY` in the EXPIRED state, since we should not assume
the partner is active by default.
This ensures that in passive mode, the bond starts sending periodic LACPDUs
after receiving one from the partner, and avoids flapping due to inactivity.
Fixes: 3a755cd8b7 ("bonding: add new option lacp_active")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250815062000.22220-3-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b64d035f77 ]
The port's actor_oper_port_state activity flag should be updated immediately
after changing the lacp_active option to reflect the current mode correctly.
Fixes: 3a755cd8b7 ("bonding: add new option lacp_active")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250815062000.22220-2-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e318cd6714 ]
ksz9477_hsr_join() is called once to setup the HSR port membership, but
the port can be enabled later, or disabled and enabled back and the port
membership is not set correctly inside ksz_update_port_member(). The
added code always use the correct HSR port membership for HSR port that
is enabled.
Fixes: 2d61298fdd ("net: dsa: microchip: Enable HSR offloading for KSZ9477")
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Łukasz Majewski <lukma@nabladev.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20250819010457.563286-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1468c1f97c ]
Device ID comparison in igc_is_device_id_i226 is performed before
the ID is set, resulting in always failing check on init.
Before the patch:
* L1.2 is not disabled on init
* L1.2 is properly disabled after suspend-resume cycle
With the patch:
* L1.2 is properly disabled both on init and after suspend-resume
How to test:
Connect to the 1G link with 300+ mbit/s Internet speed, and run
the download speed test, such as:
curl -o /dev/null http://speedtest.selectel.ru/1GB
Without L1.2 disabled, the speed would be no more than ~200 mbit/s.
With L1.2 disabled, the speed would reach 1 gbit/s.
Note: it's required that the latency between your host and the remote
be around 3-5 ms, the test inside LAN (<1 ms latency) won't trigger the
issue.
Link: https://lore.kernel.org/intel-wired-lan/15248b4f-3271-42dd-8e35-02bfc92b25e1@intel.com
Fixes: 0325143b59 ("igc: disable L1.2 PCI-E link substate to avoid performance issue")
Signed-off-by: ValdikSS <iam@valdikss.org.ru>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250819222000.3504873-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d4d9ef9df ]
Resolve the budget negative overflow which leads to returning true in
ixgbe_xmit_zc even when the budget of descs are thoroughly consumed.
Before this patch, when the budget is decreased to zero and finishes
sending the last allowed desc in ixgbe_xmit_zc, it will always turn back
and enter into the while() statement to see if it should keep processing
packets, but in the meantime it unexpectedly decreases the value again to
'unsigned int (0--)', namely, UINT_MAX. Finally, the ixgbe_xmit_zc returns
true, showing 'we complete cleaning the budget'. That also means
'clean_complete = true' in ixgbe_poll.
The true theory behind this is if that budget number of descs are consumed,
it implies that we might have more descs to be done. So we should return
false in ixgbe_xmit_zc to tell napi poll to find another chance to start
polling to handle the rest of descs. On the contrary, returning true here
means job done and we know we finish all the possible descs this time and
we don't intend to start a new napi poll.
It is apparently against our expectations. Please also see how
ixgbe_clean_tx_irq() handles the problem: it uses do..while() statement
to make sure the budget can be decreased to zero at most and the negative
overflow never happens.
The patch adds 'likely' because we rarely would not hit the loop condition
since the standard budget is 256.
Fixes: 8221c5eba8 ("ixgbe: add AF_XDP zero-copy Tx support")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Priya Singh <priyax.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250819222000.3504873-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cd58fec91 ]
Fix missing configuration for LAN865x silicon revisions B0 and B1 as per
Microchip Application Note AN1760 (Rev F, June 2024).
The Timer Increment register was not being set, which is required for
accurate timestamping. As per the application note, configure the MAC to
set timestamping at the end of the Start of Frame Delimiter (SFD), and
set the Timer Increment register to 40 ns (corresponding to a 25 MHz
internal clock).
Link: https://www.microchip.com/en-us/application-notes/an1760
Fixes: 5cd2340cb6 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY")
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250818060514.52795-3-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1683fd1b2f ]
This fixes an issue where the transmit queue is started implicitly only
the very first time the device is registered. When the device is taken
down and brought back up again (using `ip` or `ifconfig`), the transmit
queue is not restarted, causing packet transmission to hang.
Adding an explicit call to netif_start_queue() in lan865x_net_open()
ensures the transmit queue is properly started every time the device
is reopened.
Fixes: 5cd2340cb6 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY")
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20250818060514.52795-2-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75a9a46d67 ]
A crash can occur if an ethtool operation is invoked
after shutdown() is called.
shutdown() is invoked during system shutdown to stop DMA operations
without performing expensive deallocations. It is discouraged to
unregister the netdev in this path, so the device may still be visible
to userspace and kernel helpers.
In gve, shutdown() tears down most internal data structures. If an
ethtool operation is dispatched after shutdown(), it will dereference
freed or NULL pointers, leading to a kernel panic. While graceful
shutdown normally quiesces userspace before invoking the reboot
syscall, forced shutdowns (as observed on GCP VMs) can still trigger
this path.
Fix by calling netif_device_detach() in shutdown().
This marks the device as detached so the ethtool ioctl handler
will skip dispatching operations to the driver.
Fixes: 974365e518 ("gve: Implement suspend/resume/shutdown")
Signed-off-by: Jordan Rhee <jordanrhee@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250818211245.1156919-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc1a59cff9 ]
There was a problem when we received frames and the frames were
timestamped. The driver is configured to store the nanosecond part of
the timestmap in the ptp reserved bits and it would take the second part
by reading the LTC. The problem is that when reading the LTC we are in
atomic context and to read the second part will go over mdio bus which
might sleep, so we get an error.
The fix consists in actually put all the frames in a queue and start the
aux work and in that work to read the LTC and then calculate the full
received time.
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250818081029.1300780-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01792bc3e5 ]
To enable HSR / Switch offload, certain configurations are needed.
Currently they are done inside icssg_change_mode(). This function only
gets called if we move from one mode to another without bringing the
links up / down.
Once in HSR / Switch mode, if we bring the links down and bring it back
up again. The callback sequence is,
- emac_ndo_stop()
Firmwares are stopped
- emac_ndo_open()
Firmwares are loaded
In this path icssg_change_mode() doesn't get called and as a result the
configurations needed for HSR / Switch is not done.
To fix this, put all these configurations in a separate function
icssg_enable_fw_offload() and call this from both icssg_change_mode()
and emac_ndo_open()
Fixes: 56375086d0 ("net: ti: icssg-prueth: Enable HSR Tx duplication, Tx Tag and Rx Tag offload")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20250814105106.1491871-1-danishanwar@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0417adf367 ]
ppp_fill_forward_path() has two race conditions:
1. The ppp->channels list can change between list_empty() and
list_first_entry(), as ppp_lock() is not held. If the only channel
is deleted in ppp_disconnect_channel(), list_first_entry() may
access an empty head or a freed entry, and trigger a panic.
2. pch->chan can be NULL. When ppp_unregister_channel() is called,
pch->chan is set to NULL before pch is removed from ppp->channels.
Fix these by using a lockless RCU approach:
- Use list_first_or_null_rcu() to safely test and access the first list
entry.
- Convert list modifications on ppp->channels to their RCU variants and
add synchronize_net() after removal.
- Check for a NULL pch->chan before dereferencing it.
Fixes: f6efc675c9 ("net: ppp: resolve forwarding path for bridge pppoe devices")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://patch.msgid.link/20250814012559.3705-2-dqfext@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f604d3aaf6 ]
By default, the device does not forward IPv4 packets with a link-local
source IP (i.e., 169.254.0.0/16). This behavior does not align with the
kernel which does forward them.
Fix by instructing the device to forward such packets instead of
dropping them.
Fixes: ca360db4b8 ("mlxsw: spectrum: Disable DIP_LINK_LOCAL check in hardware pipeline")
Reported-by: Zoey Mertes <zoey@cloudflare.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/6721e6b2c96feb80269e72ce8d0b426e2f32d99c.1755174341.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 065c31f2c6 ]
The CRC error bit is located at bit 17 in the Rx descriptor, but the
driver was incorrectly using bit 16. Fix it.
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20250813071631.7566-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd980bf6e9 ]
Submit multiple descriptors in axienet_rx_cb() to fill Rx skb ring. This
ensures the ring "catches up" on previously missed allocations.
Increment Rx skb ring head pointer after BD is successfully allocated.
Previously, head pointer was incremented before verifying if descriptor is
successfully allocated and has valid entries, which could lead to ring
state inconsistency if descriptor setup failed.
These changes improve reliability by maintaining adequate descriptor
availability and ensuring proper ring buffer state management.
Fixes: 6a91b846af ("net: axienet: Introduce dmaengine support")
Signed-off-by: Suraj Gupta <suraj.gupta2@amd.com>
Link: https://patch.msgid.link/20250813135559.1555652-1-suraj.gupta2@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aa6956150f upstream.
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-6-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6efa0df540 upstream.
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-5-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c1ba5091f upstream.
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath11k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath11k_hal_srng_access_end().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed32169be1 upstream.
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-5-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e834da4cbd upstream.
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-4-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8157ce533a upstream.
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath12k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath12k_hal_srng_access_end().
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81284e86bf upstream.
A new warning in clang [1] complains that diq_start in
wlc_lcnphy_tx_iqlo_cal() is passed uninitialized as a const pointer to
wlc_lcnphy_common_read_table():
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2728:13: error: variable 'diq_start' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
2728 | &diq_start, 1, 16, 69);
| ^~~~~~~~~
The table pointer passed to wlc_lcnphy_common_read_table() should not be
considered constant, as wlc_phy_read_table() is ultimately going to
update it. Remove the const qualifier from the tbl_ptr to clear up the
warning.
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issues/2108
Fixes: 5b435de0d7 ("net: wireless: add brcm80211 drivers")
Link: 00dacf8c22 [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>>
Link: https://patch.msgid.link/20250715-brcmsmac-fix-uninit-const-pointer-v1-1-16e6a51a8ef4@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57ec5a8735 ]
According to the LAN8710A datasheet (Rev. B, section 3.8.5.1), a hardware
reset is required after power-on, and the reference clock (REF_CLK) must be
established before asserting reset.
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Cc: Csókás Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250728152916.46249-2-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9080abea1 ]
Since the kern_dbpage gets set up in ionic_lif_init() and that
function's error path will clean it if needed, the kern_dbpage
on teardown should be cleaned in ionic_lif_deinit(), not in
ionic_lif_free(). As it is currently we get a double call
to iounmap() on kern_dbpage if the PCI ionic fails setting up
the lif. One example of this is when firmware isn't responding
to AdminQ requests and ionic's first AdminQ call fails to
setup the NotifyQ.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Joe Damato <joe@dama.to>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76b3e5078d ]
When `dma_mapping_error()` is true, if a new `skb` has been allocated,
then it must be de-allocated.
Compile tested only
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250613074014.69856-2-fourier.thomas@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3db8563bac ]
If scan happen during start_ap, the register which control TX might be
turned off during scan. Additionally, if set_channel occurs during scan
will backup this register and set to firmware after set_channel done.
When scan complete, firmware will also set TX by this register, causing
TX to be disabled and beacon can't be TX. Therefore, in assign/unassign_vif
call scan abort before set_channel to avoid scan racing with set_channel.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250610130034.14692-13-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37883bbc45 ]
BCM5325 doesn't implement GMII_PORT_OVERRIDE_CTRL register so we should
avoid reading or writing it.
PORT_OVERRIDE_RX_FLOW and PORT_OVERRIDE_TX_FLOW aren't defined on BCM5325
and we should use PORT_OVERRIDE_LP_FLOW_25 instead.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-12-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c00df10187 ]
CPU port should be B53_CPU_PORT instead of B53_CPU_PORT_25 for
B53_PVLAN_PORT_MASK register.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-14-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 966a83df36 ]
According to the datasheet, BCM5325 uses B53_PD_MODE_CTRL_25 register to
disable clocking to individual PHYs.
Only ports 1-4 can be enabled or disabled and the datasheet is explicit
about not toggling BIT(0) since it disables the PLL power and the switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250614080000.1884236-15-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11344f63f ]
In gve_adminq_issue_cmd(), return -EINVAL instead of 0 when an unknown
admin queue command opcode is encountered.
This prevents the function from silently succeeding on invalid input
and prevents undefined behavior by ensuring the function fails gracefully
when an unrecognized opcode is provided.
These changes improve error handling.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20250616054504.1644770-2-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8155c1df5 ]
This effectively reverts 6e8b0ff1ba ("dpaa_eth: Add change_carrier()
for Fixed PHYs"). Usage of fixed_phy_change_carrier() requires that
fixed_phy_register() has been called before, directly or indirectly.
And that's not the case in this driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/7eb189b3-d5fd-4be6-8517-a66671a4e4e3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de19d5ae0 ]
Limit rate_idx to IL_LAST_OFDM_RATE for 5GHz band for thinkable case
the index is incorrect.
Reported-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reported-by: Alexei Safin <a.safin@rosa.ru>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Reviewed-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20250525144524.GA172583@wp.pl
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c0884fcd2 ]
Currently, TID is not decremented before peer cleanup, during error
handling path of ath12k_dp_rx_peer_frag_setup(). This could lead to
out-of-bounds access in peer->rx_tid[].
Hence, add a decrement operation for TID, before peer cleanup to
ensures proper cleanup and prevents out-of-bounds access issues when
the RX peer frag setup fails.
Found during code review. Compile tested only.
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250526034713.712592-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b79742b84e ]
The commit 89ac53e962 ("wifi: ath12k: Enable REO queue lookup table
feature on QCN9274") originally intended to enable the reoq_lut_support
hardware parameter flag for both QCN9274 hw1.0 and hw2.0. However,
it enabled it only for QCN9274 hw1.0.
Hence, enable REO queue lookup table feature on QCN9274 hw2.0.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250609-qcn9274-reoq-v1-1-a92c91abc9b9@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44c0e19100 ]
The function `_rtl_pci_init_one_rxdesc()` can fail even when the new
`skb` is passed because of a DMA mapping error. If it fails, the `skb`
is not saved in the rx ringbuffer and thus lost.
Compile tested only
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250616105631.444309-4-fourier.thomas@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3ad987e9d ]
The 'index' variable in the rs_fill_link_cmd() function can reach
LINK_QUAL_MAX_RETRY_NUM during the execution of the inner loop. This
variable is used as an index for the lq_cmd->rs_table array, which has a
size of LINK_QUAL_MAX_RETRY_NUM, without proper validation.
Modify the condition of the inner loop to ensure that the 'index' variable
does not exceed LINK_QUAL_MAX_RETRY_NUM - 1, thereby preventing any
potential overflow issues.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Link: https://patch.msgid.link/20240313101755.269209-1-rand.sec96@gmail.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70eeacc1a9 ]
ath12k station is unable to associate with non-transmitting BSSes
in a Multiple BSS set because the user-space does not receive
information about the non-transmitting BSSes from mac80211's
scan results.
The ath12k driver does not advertise its MBSSID capability to mac80211,
resulting in wiphy->support_mbssid not being set. Consequently, the
information about non-transmitting BSS is not parsed from received
Beacon/Probe response frames and is therefore not included in the
scan results.
Fix this by advertising the MBSSID capability of ath12k driver to
mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9903c0986f ]
When both AP/STA and monitor interfaces are enabled, ieee80211_tx_status()
is invoked from two paths: the TX completion handler for data frames
and the WMI TX completion handler for management frames.
In the data path, the skb->cb is properly zeroed using memset, but in
the WMI path, this step is missing.
As a result, mac80211 encountered uninitialized (junk) values in
skb->cb when generating the radiotap header for monitor mode, leading
to invalid radiotap lengths.
Hence, explicitly zero the status field in the skb->cb using memset
in WMI TX completion path to ensure consistent and correct behavior
during WMI tx completion path.
Additionally, set info->status.rates[0].idx = -1 to indicate that
no valid rate information is available, avoiding misinterpretation of
garbage values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250603063512.1887652-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
