commit c2415c407a upstream.
Prior to the topology parsing rewrite and the switchover to the new parsing
logic for AMD processors in
c749ce393b ("x86/cpu: Use common topology code for AMD"),
the initial_apicid on these platforms was:
- First initialized to the LocalApicId from CPUID leaf 0x1 EBX[31:24].
- Then overwritten by the ExtendedLocalApicId in CPUID leaf 0xb
EDX[31:0] on processors that supported topoext.
With the new parsing flow introduced in
f7fb3b2dd9 ("x86/cpu: Provide an AMD/HYGON specific topology parser"),
parse_8000_001e() now unconditionally overwrites the initial_apicid already
parsed during cpu_parse_topology_ext().
Although this has not been a problem on baremetal platforms, on virtualized AMD
guests that feature more than 255 cores, QEMU zeros out the CPUID leaf
0x8000001e on CPUs with CoreID > 255 to prevent collision of these IDs in
EBX[7:0] which can only represent a maximum of 255 cores [1].
This results in the following FW_BUG being logged when booting a guest
with more than 255 cores:
[Firmware Bug]: CPU 512: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0200
AMD64 Architecture Programmer's Manual Volume 2: System Programming Pub.
24593 Rev. 3.42 [2] Section 16.12 "x2APIC_ID" mentions the Extended
Enumeration leaf 0xb (Fn0000_000B_EDX[31:0])(which was later superseded by the
extended leaf 0x80000026) provides the full x2APIC ID under all circumstances
unlike the one reported by CPUID leaf 0x8000001e EAX which depends on the mode
in which APIC is configured.
Rely on the APIC ID parsed during cpu_parse_topology_ext() from CPUID leaf
0x80000026 or 0xb and only use the APIC ID from leaf 0x8000001e if
cpu_parse_topology_ext() failed (has_topoext is false).
On platforms that support the 0xb leaf (Zen2 or later, AMD guests on
QEMU) or the extended leaf 0x80000026 (Zen4 or later), the
initial_apicid is now set to the value parsed from EDX[31:0].
On older AMD/Hygon platforms that do not support the 0xb leaf but support the
TOPOEXT extension (families 0x15, 0x16, 0x17[Zen1], and Hygon), retain current
behavior where the initial_apicid is set using the 0x8000001e leaf.
Issue debugged by Naveen N Rao (AMD) <naveen@kernel.org> and Sairaj Kodilkar
<sarunkod@amd.com>.
[ bp: Massage commit message. ]
Fixes: c749ce393b ("x86/cpu: Use common topology code for AMD")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Naveen N Rao (AMD) <naveen@kernel.org>
Cc: stable@vger.kernel.org
Link: 35ac5dfbca [1]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537 [2]
Link: https://lore.kernel.org/20250825075732.10694-2-kprateek.nayak@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcf8239ad6 upstream.
Machines can be shipped without any microcode in the BIOS. Which means,
the microcode patch revision is 0.
Handle that gracefully.
Fixes: 94838d230a ("x86/microcode/AMD: Use the family,model,stepping encoded in the patch ID")
Reported-by: Vítek Vávra <vit.vavra.kh@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 799766208f upstream.
The userspace load can put up to 2048 bits into an xlen bit stack
buffer. We want only xlen bits, so check the size beforehand.
Fixes: 2fa290372d ("RISC-V: KVM: add 'vlenb' Vector CSR")
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@ventanamicro.com>
Reviewed-by: Nutty Liu <liujingqi@lanxincomputing.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Link: https://lore.kernel.org/r/20250805104418.196023-4-rkrcmar@ventanamicro.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88688a2c8a ]
When compiling for pseries or powernv defconfig with "make C=1",
these warning were reported bu sparse tool in powerpc/kernel/kvm.c
arch/powerpc/kernel/kvm.c:635:9: warning: switch with no cases
arch/powerpc/kernel/kvm.c:646:9: warning: switch with no cases
Currently #ifdef were added after the switch case which are specific
for BOOKE and PPC_BOOK3S_32. These are not enabled in pseries/powernv
defconfig. Fix it by moving the #ifdef before switch(){}
Fixes: cbe487fac7 ("KVM: PPC: Add mtsrin PV code")
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250518044107.39928-1-maddy@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c431ea8f3 ]
Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad937 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b28232921 ]
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0 ("net: lantiq: configure the burst length in ethernet drivers")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3868f91044 ]
When kernel lockdown is active, debugfs_locked_down() blocks access to
hypfs files that register ioctl callbacks, even if the ioctl interface
is not required for a function. This unnecessarily breaks userspace
tools that only rely on read operations.
Resolve this by registering a minimal set of file operations during
lockdown, avoiding ioctl registration and preserving access for affected
tooling.
Note that this change restores hypfs functionality when lockdown is
active from early boot (e.g. via lockdown=integrity kernel parameter),
but does not apply to scenarios where lockdown is enabled dynamically
while Linux is running.
Tested-by: Mete Durlu <meted@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Fixes: 5496197f9b ("debugfs: Restrict debugfs when the kernel is locked down")
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fec7bdfe7f ]
Currently, hypfs registers ioctl callbacks for all debugfs files,
despite only one file requiring them. This leads to unintended exposure
of unused interfaces to user space and can trigger side effects such as
restricted access when kernel lockdown is enabled.
Restrict ioctl registration to only those files that implement ioctl
functionality to avoid interface clutter and unnecessary access
restrictions.
Tested-by: Mete Durlu <meted@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Fixes: 5496197f9b ("debugfs: Restrict debugfs when the kernel is locked down")
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93f616ff87 ]
Since the identity mapping is pinned to address zero the lowcore is always
also mapped to address zero, this happens regardless of the relocate_lowcore
command line option. If the option is specified the lowcore is mapped
twice, instead of only once.
This means that NULL pointer accesses will succeed instead of causing an
exception (low address protection still applies, but covers only parts).
To fix this never map the first two pages of physical memory with the
identity mapping.
Fixes: 32db401965 ("s390/mm: Pin identity mapping base to zero")
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63dbd8fb2a ]
When enabling CONFIG_KASAN, CONFIG_PREEMPT_VOLUNTARY_BUILD and
CONFIG_PREEMPT_VOLUNTARY at the same time, there will be soft deadlock,
the relevant logs are as follows:
rcu: INFO: rcu_sched self-detected stall on CPU
...
Call Trace:
[<900000000024f9e4>] show_stack+0x5c/0x180
[<90000000002482f4>] dump_stack_lvl+0x94/0xbc
[<9000000000224544>] rcu_dump_cpu_stacks+0x1fc/0x280
[<900000000037ac80>] rcu_sched_clock_irq+0x720/0xf88
[<9000000000396c34>] update_process_times+0xb4/0x150
[<90000000003b2474>] tick_nohz_handler+0xf4/0x250
[<9000000000397e28>] __hrtimer_run_queues+0x1d0/0x428
[<9000000000399b2c>] hrtimer_interrupt+0x214/0x538
[<9000000000253634>] constant_timer_interrupt+0x64/0x80
[<9000000000349938>] __handle_irq_event_percpu+0x78/0x1a0
[<9000000000349a78>] handle_irq_event_percpu+0x18/0x88
[<9000000000354c00>] handle_percpu_irq+0x90/0xf0
[<9000000000348c74>] handle_irq_desc+0x94/0xb8
[<9000000001012b28>] handle_cpu_irq+0x68/0xa0
[<9000000001def8c0>] handle_loongarch_irq+0x30/0x48
[<9000000001def958>] do_vint+0x80/0xd0
[<9000000000268a0c>] kasan_mem_to_shadow.part.0+0x2c/0x2a0
[<90000000006344f4>] __asan_load8+0x4c/0x120
[<900000000025c0d0>] module_frob_arch_sections+0x5c8/0x6b8
[<90000000003895f0>] load_module+0x9e0/0x2958
[<900000000038b770>] __do_sys_init_module+0x208/0x2d0
[<9000000001df0c34>] do_syscall+0x94/0x190
[<900000000024d6fc>] handle_syscall+0xbc/0x158
After analysis, this is because the slow speed of loading the amdgpu
module leads to the long time occupation of the cpu and then the soft
deadlock.
When loading a module, module_frob_arch_sections() tries to figure out
the number of PLTs/GOTs that will be needed to handle all the RELAs. It
will call the count_max_entries() to find in an out-of-order date which
counting algorithm has O(n^2) complexity.
To make it faster, we sort the relocation list by info and addend. That
way, to check for a duplicate relocation, it just needs to compare with
the previous entry. This reduces the complexity of the algorithm to O(n
log n), as done in commit d4e0340919 ("arm64/module: Optimize module
load time by optimizing PLT counting"). This gives sinificant reduction
in module load time for modules with large number of relocations.
After applying this patch, the soft deadlock problem has been solved,
and the kernel starts normally without "Call Trace".
Using the default configuration to test some modules, the results are as
follows:
Module Size
ip_tables 36K
fat 143K
radeon 2.5MB
amdgpu 16MB
Without this patch:
Module Module load time (ms) Count(PLTs/GOTs)
ip_tables 18 59/6
fat 0 162/14
radeon 54 1221/84
amdgpu 1411 4525/1098
With this patch:
Module Module load time (ms) Count(PLTs/GOTs)
ip_tables 18 59/6
fat 0 162/14
radeon 22 1221/84
amdgpu 45 4525/1098
Fixes: fcdfe9d22b ("LoongArch: Add ELF and module support")
Signed-off-by: Kanglong Wang <wangkanglong@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d8df126349 upstream.
Since
923f3a2b48 ("x86/resctrl: Query LLC monitoring properties once during boot")
resctrl_cpu_detect() has been moved from common CPU initialization code to
the vendor-specific BSP init helper, while Hygon didn't put that call in their
code.
This triggers a division by zero fault during early booting stage on our
machines with X86_FEATURE_CQM* supported, where get_rdt_mon_resources() tries
to calculate mon_l3_config with uninitialized boot_cpu_data.x86_cache_occ_scale.
Add the missing resctrl_cpu_detect() in the Hygon BSP init helper.
[ bp: Massage commit message. ]
Fixes: 923f3a2b48 ("x86/resctrl: Query LLC monitoring properties once during boot")
Signed-off-by: Tianxiang Peng <txpeng@tencent.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Hui Li <caelli@tencent.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/20250623093153.3016937-1-txpeng@tencent.com
Signed-off-by: Tianxiang Peng <txpeng@tencent.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a821e2d69 upstream.
Similar to x86 the ppc boot code does not build with GCC 15.
Copy the fix from
commit ee2ab467bd ("x86/boot: Use '-std=gnu11' to fix build with GCC 15")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Tested-by: Amit Machhiwal <amachhiw@linux.ibm.com>
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250331105722.19709-1-msuchanek@suse.de
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ea815399c ]
__ADDRESSABLE_ASM_STR() is where the necessary stringification happens.
As long as "sym" doesn't contain any odd characters, no quoting is
required for its use with .quad / .long. In fact the quotation gets in
the way with gas 2.25; it's only from 2.26 onwards that quoted symbols
are half-way properly supported.
However, assembly being different from C anyway, drop
__ADDRESSABLE_ASM_STR() and its helper macro altogether. A simple
.global directive will suffice to get the symbol "declared", i.e. into
the symbol table. While there also stop open-coding STATIC_CALL_TRAMP()
and STATIC_CALL_KEY().
Fixes: 0ef8047b73 ("x86/static-call: provide a way to do very early static-call updates")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <609d2c74-de13-4fae-ab1a-1ec44afb948d@suse.com>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0b8da0415 ]
This moves pinmux child nodes for sdhci0 node from k3-am62x-sk-common
to each top level board file. This is needed since we require internal
pullups for AM62x SK and not for AM62 LP SK since it has external
pullups on DATA 1-7.
Internal pulls are required for AM62 SK as per JESD84 spec
recommendation to prevent unconnected lines floating.
Fixes: d19a66ae48 ("arm64: dts: ti: k3-am625-sk: Enable on board peripherals")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250707190830.3951619-1-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef839ba814 ]
Remove disable-wp flag for eMMC nodes since this flag is
only applicable to SD according to the binding doc
(mmc/mmc-controller-common.yaml).
For eMMC, this flag should be ignored but lets remove
anyways to cleanup sdhci nodes.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://lore.kernel.org/r/20250429151454.4160506-4-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: a0b8da0415 ("arm64: dts: ti: k3-am62*: Move eMMC pinmux to top level board file")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db3cd905b8 ]
The bootph-all flag was introduced in dt-schema
(dtschema/schemas/bootph.yaml) to define node usage across
different boot phases.
For eMMC and SD boot modes, voltage regulator nodes, io-expander
nodes, gpio nodes, and MMC nodes need to be present in all boot
stages, so add missing bootph-all phase flag to these nodes to
support SD boot and eMMC boot.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://lore.kernel.org/r/20250429151454.4160506-2-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: a0b8da0415 ("arm64: dts: ti: k3-am62*: Move eMMC pinmux to top level board file")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 916b7f42b3 upstream.
A VMM may send a non-fatal signal to its threads, including vCPU tasks,
at any time, and thus may signal vCPU tasks during KVM_RUN. If a vCPU
task receives the signal while its trying to spawn the huge page recovery
vhost task, then KVM_RUN will fail due to copy_process() returning
-ERESTARTNOINTR.
Rework call_once() to mark the call complete if and only if the called
function succeeds, and plumb the function's true error code back to the
call_once() invoker. This provides userspace with the correct, non-fatal
error code so that the VMM doesn't terminate the VM on -ENOMEM, and allows
subsequent KVM_RUN a succeed by virtue of retrying creation of the NX huge
page task.
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
[implemented the kvm user side]
Signed-off-by: Keith Busch <kbusch@kernel.org>
Message-ID: <20250227230631.303431-3-kbusch@meta.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alistair Delva <adelva@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ee9cebd0a upstream.
In order to support future versions of the SVSM_CORE_PVALIDATE call, all
reserved fields within a PVALIDATE entry must be set to zero as an SVSM should
be ensuring all reserved fields are zero in order to support future usage of
reserved areas based on the protocol version.
Fixes: fcd042e864 ("x86/sev: Perform PVALIDATE using the SVSM when not at VMPL0")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/7cde412f8b057ea13a646fb166b1ca023f6a5031.1755098819.git.thomas.lendacky@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4be8cefc13 upstream.
Add the flag KVM_LARCH_LBT checking in function kvm_own_lbt(), so that
it can be called safely rather than duplicated enabling again.
Cc: stable@vger.kernel.org
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb22f247f3 upstream.
The following testcase exposed a problem with our read access checks
in get_user() and raw_copy_from_user():
#include <stdint.h>
#include <stddef.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
#include <errno.h>
#include <sys/mman.h>
#include <sys/types.h>
int main(int argc, char **argv)
{
unsigned long page_size = sysconf(_SC_PAGESIZE);
char *p = malloc(3 * page_size);
char *p_aligned;
/* initialize memory region. If not initialized, write syscall below will correctly return EFAULT. */
if (1)
memset(p, 'X', 3 * page_size);
p_aligned = (char *) ((((uintptr_t) p) + (2*page_size - 1)) & ~(page_size - 1));
/* Drop PROT_READ protection. Kernel and userspace should fault when accessing that memory region */
mprotect(p_aligned, page_size, PROT_NONE);
/* the following write() should return EFAULT, since PROT_READ was dropped by previous mprotect() */
int ret = write(2, p_aligned, 1);
if (!ret || errno != EFAULT)
printf("\n FAILURE: write() did not returned expected EFAULT value\n");
return 0;
}
Because of the way _PAGE_READ is handled, kernel code never generates
a read access fault when it access a page as the kernel privilege level
is always less than PL1 in the PTE.
This patch reworks the comments in the make_insert_tlb macro to try
to make this clearer.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6334f4ae9 upstream.
We use load and stbys,e instructions to trigger memory reference
interruptions without writing to memory. Because of the way read
access support is implemented, read access interruptions are only
triggered at privilege levels 2 and 3. The kernel and gateway
page execute at privilege level 0, so this code never triggers
a read access interruption. Thus, it is currently possible for
user code to execute a LWS compare and swap operation at an
address that is read protected at privilege level 3 (PRIV_USER).
Fix this by probing read access rights at privilege level 3 and
branching to lws_fault if access isn't allowed.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89f686a0fb upstream.
Because of the way read access support is implemented, read access
interruptions are only triggered at privilege levels 2 and 3. The
kernel executes at privilege level 0, so __get_user() never triggers
a read access interruption (code 26). Thus, it is currently possible
for user code to access a read protected address via a system call.
Fix this by probing read access rights at privilege level 3 (PRIV_USER)
and setting __gu_err to -EFAULT (-14) if access isn't allowed.
Note the cmpiclr instruction does a 32-bit compare because COND macro
doesn't work inside asm.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52ce9406a9 upstream.
The local name used in cache.c conflicts the declaration in
include/asm-generic/tlb.h.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 305ab0a748 upstream.
For building a 64-bit kernel, both 32-bit and 64-bit VDSO binaries
are built, so both 32-bit and 64-bit compilers (and tools) should be
in the PATH environment variable.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 802e55488b upstream.
When a PTE is changed, we need to flush the PTE. set_pte_at()
was lost in the folio update. PA-RISC version is the same as
the generic version.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91428ca932 upstream.
Because of the way the _PAGE_READ is handled in the parisc PTE, an
access interruption is not generated when the kernel reads from a
region where the _PAGE_READ is zero. The current code was written
assuming read access faults would also occur in the kernel.
This change adds user access checks to raw_copy_from_user(). The
prober_user() define checks whether user code has read access to
a virtual address. Note that page faults are not handled in the
exception support for the probe instruction. For this reason, we
precede the probe by a ldb access check.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e44ac61ab upstream.
main_uart1 reserved for TIFS firmware traces is routed to the
onboard FT4232 via a FET switch which is connected to pin A21 and
B21 of the SoC and not E17 and C17. Fix it.
Fixes: cf39ff15cc ("arm64: dts: ti: k3-am62a7-sk: Describe main_uart1 and wkup_uart")
Cc: stable@vger.kernel.org
Signed-off-by: Hong Guan <hguan@ti.com>
[bb@ti.com: expanded commit message]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250707-uart-fixes-v1-1-8164147218b0@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4292564c71 upstream.
ufs-exynos driver configures the sysreg shareability as
cacheable for gs101 so we need to set the dma-coherent
property so the descriptors are also allocated cacheable.
This fixes the UFS stability issues we have seen with
the upstream UFS driver on gs101.
Fixes: 4c65d7054b ("arm64: dts: exynos: gs101: Add ufs and ufs-phy dt nodes")
Cc: stable@vger.kernel.org
Suggested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Tested-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250314-ufs-dma-coherent-v1-1-bdf9f9be2919@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b27212788 upstream.
Switch Schmitt Trigger functions for PIN_INPUT* macros by default. This is
HW PoR configuration, the slew rate requirements without ST enabled are
pretty tough for these devices. We've noticed spurious GPIO interrupts even
with noise-free edges but not meeting slew rate requirements (3.3E+6 V/s
for 3.3v LVCMOS).
It's not obvious why one might want to disable the PoR-enabled ST on any
pin. Just enable it by default. As it's not possible to provide OR-able
macros to disable the ST, shall anyone require it, provide a set of
new macros with _NOST suffix.
Fixes: fe49f2d776 ("arm64: dts: ti: Use local header for pinctrl register values")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20250701105437.3539924-1-alexander.sverdlin@siemens.com
[vigneshr@ti.com: Add Fixes tag]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22375adaa0 upstream.
The MIPS32r2 ChaCha code has never been buildable with the clang
assembler. First, clang doesn't support the 'rotl' pseudo-instruction:
error: unknown instruction, did you mean: rol, rotr?
Second, clang requires that both operands of the 'wsbh' instruction be
explicitly given:
error: too few operands for instruction
To fix this, align the code with the real instruction set by (1) using
the real instruction 'rotr' instead of the nonstandard pseudo-
instruction 'rotl', and (2) explicitly giving both operands to 'wsbh'.
To make removing the use of 'rotl' a bit easier, also remove the
unnecessary special-casing for big endian CPUs at
.Lchacha_mips_xor_bytes. The tail handling is actually
endian-independent since it processes one byte at a time. On big endian
CPUs the old code byte-swapped SAVED_X, then iterated through it in
reverse order. But the byteswap and reverse iteration canceled out.
Tested with chacha20poly1305-selftest in QEMU using "-M malta" with both
little endian and big endian mips32r2 kernels.
Fixes: 49aa7c00ed ("crypto: mips/chacha - import 32r2 ChaCha code from Zinc")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505080409.EujEBwA0-lkp@intel.com/
Link: https://lore.kernel.org/r/20250619225535.679301-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 210a1ce8ed upstream.
Move the cursor position rightward after rendering the character,
not before. This avoids complications that arise when the recursive
console_putc call has to wrap the line and/or scroll the display.
This also fixes the linewrap bug that crops off the rightmost column.
When the cursor is at the bottom of the display, a linefeed will not
move the cursor position further downward. Instead, the display scrolls
upward. Avoid the repeated add/subtract sequence by way of a single
subtraction at the initialization of console_struct_num_rows.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/9d4e8c68a456d5f2bc254ac6f87a472d066ebd5e.1743115195.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65ba2a6e77 ]
According to the "GPIO Expander Map / Table" section of the J722S EVM
Schematic within the Evaluation Module Design Files package [0], the
GPIO Pin P05 located on the GPIO Expander 1 (I2C0/0x23) has to be pulled
down to select the Type-C interface. Since commit under Fixes claims to
enable the Type-C interface, update the property within "p05-hog" from
"output-high" to "output-low", thereby switching from the Type-A
interface to the Type-C interface.
[0]: https://www.ti.com/lit/zip/sprr495
Cc: stable@vger.kernel.org
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250623100657.4082031-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc8d9e6b58 ]
J722S SOC has two usb controllers USB0 and USB1. USB0 is brought out on
the EVM as a stacked USB connector which has one Type-A and one Type-C
port. These Type-A and Type-C ports are connected to MUX so only
one of them can be enabled at a time.
Commit under Fixes, tries to enable the USB0 instance of USB to
interface with the Type-C port via the USB hub, by configuring the
USB2.0_MUX_SEL to GPIO_ACTIVE_HIGH. But it is observed on J722S-EVM
that Type-A port is enabled instead of Type-C port.
Fix this by setting USB2.0_MUX_SEL to GPIO_ACTIVE_LOW to enable Type-C
port.
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20250116125726.2549489-1-h-salunke@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Stable-dep-of: 65ba2a6e77 ("arm64: dts: ti: k3-j722s-evm: Fix USB gpio-hog level for Type-C")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59305202c6 upstream.
Memory hot remove unmaps and tears down various kernel page table regions
as required. The ptdump code can race with concurrent modifications of
the kernel page tables. When leaf entries are modified concurrently, the
dump code may log stale or inconsistent information for a VA range, but
this is otherwise not harmful.
But when intermediate levels of kernel page table are freed, the dump code
will continue to use memory that has been freed and potentially
reallocated for another purpose. In such cases, the ptdump code may
dereference bogus addresses, leading to a number of potential problems.
To avoid the above mentioned race condition, platforms such as arm64,
riscv and s390 take memory hotplug lock, while dumping kernel page table
via the sysfs interface /sys/kernel/debug/kernel_page_tables.
Similar race condition exists while checking for pages that might have
been marked W+X via /sys/kernel/debug/kernel_page_tables/check_wx_pages
which in turn calls ptdump_check_wx(). Instead of solving this race
condition again, let's just move the memory hotplug lock inside generic
ptdump_check_wx() which will benefit both the scenarios.
Drop get_online_mems() and put_online_mems() combination from all existing
platform ptdump code paths.
Link: https://lkml.kernel.org/r/20250620052427.2092093-1-anshuman.khandual@arm.com
Fixes: bbd6ec605c ("arm64/mm: Enable memory hot remove")
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dev Jain <dev.jain@arm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> [s390]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c9a7ff988 ]
request_mem_region() will return NULL instead of error code
when the memory request fails. Therefore, we should check if
the return value is non-zero instead of less than zero. In
this way, this patch also fixes the build warnings:
arch/mips/lantiq/falcon/sysctrl.c:214:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
214 | res_status.name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:216:47: error: ordered comparison of pointer with integer zero [-Werror=extra]
216 | res_ebu.name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:219:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
219 | res_sys[0].name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:222:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
222 | res_sys[1].name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:225:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
225 | res_sys[2].name) < 0))
|
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9f4a6b342 ]
Not all tasks have an ABI associated or vDSO mapped,
for example kthreads never do.
If such a task ever ends up calling stack_top(), it will derefence the
NULL ABI pointer and crash.
This can for example happen when using kunit:
mips_stack_top+0x28/0xc0
arch_pick_mmap_layout+0x190/0x220
kunit_vm_mmap_init+0xf8/0x138
__kunit_add_resource+0x40/0xa8
kunit_vm_mmap+0x88/0xd8
usercopy_test_init+0xb8/0x240
kunit_try_run_case+0x5c/0x1a8
kunit_generic_run_threadfn_adapter+0x28/0x50
kthread+0x118/0x240
ret_from_kernel_thread+0x14/0x1c
Only dereference the ABI point if it is set.
The GIC page is also included as it is specific to the vDSO.
Also move the randomization adjustment into the same conditional.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 844615dd0f ]
These functions are exported but their prototypes are not defined.
This patch adds the missing function prototypes to fix the following
compilation warnings:
arch/mips/kernel/vpe-mt.c:180:7: error: no previous prototype for 'vpe_alloc' [-Werror=missing-prototypes]
180 | void *vpe_alloc(void)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:198:5: error: no previous prototype for 'vpe_start' [-Werror=missing-prototypes]
198 | int vpe_start(void *vpe, unsigned long start)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:208:5: error: no previous prototype for 'vpe_stop' [-Werror=missing-prototypes]
208 | int vpe_stop(void *vpe)
| ^~~~~~~~
arch/mips/kernel/vpe-mt.c:229:5: error: no previous prototype for 'vpe_free' [-Werror=missing-prototypes]
229 | int vpe_free(void *vpe)
| ^~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beecfd6a88 ]
If kretprobe_find_ret_addr() fails to find the original return address,
it returns 0. Check for this case so that a reliable stacktrace won't
silently ignore it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Andrea della Porta <andrea.porta@suse.com>
Cc: Breno Leitao <leitao@debian.org>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Song Liu <song@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-and-tested-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20250521111000.2237470-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf183c1730 ]
The DMA map functions can fail and should be tested for errors.
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250620075602.12575-1-fourier.thomas@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bad3fa2fb9 ]
The kernel currently alway prints:
"Use ACPI SPCR as default console: No/Yes "
even on systems that lack an SPCR table. This can
mislead users into thinking the SPCR table exists
on the machines without SPCR.
With this change, the "Yes" is only printed if
the SPCR table is present, parsed and !param_acpi_nospcr.
This avoids user confusion on SPCR-less systems.
Signed-off-by: Li Chen <chenl311@chinatelecom.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20250620131309.126555-3-me@linux.beauty
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 760b9b4f6d ]
If the device configuration fails (if `dma_dev->device_config()`),
`sg_dma_address(&sg)` is not initialized and the jump to `err_dma_prep`
leads to calling `dma_unmap_single()` on `sg_dma_address(&sg)`.
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250610142918.169540-2-fourier.thomas@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cf636c99b ]
In case of an early crash the early program check handler also prints the
last breaking event address which is contained within the pt_regs
structure. However it is not initialized, and therefore a more or less
random value is printed in case of a crash.
Copy the last breaking event address from lowcore to pt_regs in case of an
early program check to address this. This also makes it easier to analyze
early crashes.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b367017cda ]
When an stp sync check is handled on a system with multiple
cpus each cpu gets a machine check but only the first one
actually handles the sync operation. All other CPUs spin
waiting for the first one to finish with a short udelay().
But udelay can't be used here as the first CPU modifies tod_clock_base
before performing the sync op. During this timeframe
get_tod_clock_monotonic() might return a non-monotonic time.
The time spent waiting should be very short and udelay is a busy loop
anyways, therefore simply remove the udelay.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
