[ Upstream commit 43e0da37d5 ]
We already have a component driver named "RX-MACRO", which is
lpass-rx-macro.c. The tx macro component driver's name should
be "TX-MACRO" accordingly. Fix it.
Cc: Srinivas Kandagatla <srini@kernel.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20250806140030.691477-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19f971057b ]
To be more resilient to codec-detection failures when the hardware
powers on slowly, add retry mechanism to the device verification check.
Similar pattern is found throughout a number of Realtek codecs. Our
tests show that 60ms delay is sufficient to address readiness issues on
rt5640 chip.
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Xinxin Wan <xinxin.wan@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20250530142120.2944095-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4ca928a6d ]
We currently log parse failures for ELD data and some disconnection events
as errors without rate limiting. These log messages can be triggered very
frequently in some situations, especially ELD parsing when there is nothing
connected to a HDMI port which will generate:
hdmi-audio-codec hdmi-audio-codec.1.auto: HDMI: Unknown ELD version 0
While there's doubtless work that could be done on reducing the number of
connection notification callbacks it's possible these may be legitimately
generated by poor quality physical connections so let's use rate limiting
to mitigate the log spam for the parse errors and lower the severity for
disconnect logging to debug level.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20250613-asoc-hdmi-eld-logging-v1-1-76d64154d969@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b3312f28e ]
Return an error from driver probe if the DEVID read from the chip is not
one supported by this driver.
In cs35l56_hw_init() there is a check for valid DEVID, but the invalid
case was returning the value of ret. At this point in the code ret == 0
so the caller would think that cs35l56_hw_init() was successful.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 84851aa055 ("ASoC: cs35l56: Move part of cs35l56_init() to shared library")
Link: https://patch.msgid.link/20250703102521.54204-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 592ab3936b ]
When the part is reset in component_probe, do not forget to reinit the
regcache, otherwise the cache can get out of sync with the part's
actual state. This fix is similar to commit 0a0342ede3
("ASoC: tas2770: Reinit regcache on reset") which concerned the
tas2770 driver.
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250406-apple-codec-changes-v5-3-50a00ec850a3@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad18392962 ]
SN012776 is a speaker amp chip found in Apple's 2021 laptops. It appears
similar and more-or-less compatible to TAS2764. Extend the TAS2764
driver with some SN012776 specifics and configure the chip assuming
it's in one of the Apple machines.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-3-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 592ab3936b ("ASoC: tas2764: Reinit cache on part reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9079db287f ]
Driver gets and enables all regulator supplies in probe path
(wcd9335_parse_dt() and wcd9335_power_on_reset()), but does not cleanup
in final error paths and in unbind (missing remove() callback). This
leads to leaked memory and unbalanced regulator enable count during
probe errors or unbind.
Fix this by converting entire code into devm_regulator_bulk_get_enable()
which also greatly simplifies the code.
Fixes: 20aedafdf4 ("ASoC: wcd9335: add support to wcd9335 codec")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250526-b4-b4-asoc-wcd9395-vdd-px-fixes-v1-1-0b8a2993b7d3@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5099bc1b5 ]
of_gpio.h is deprecated, update the driver to use GPIO descriptors.
- Use dev_gpiod_get to get GPIO descriptor.
- Use gpiod_set_value to configure output value.
With legacy of_gpio API, the driver set gpio value 0 to assert reset,
and 1 to deassert reset. And the reset-gpios use GPIO_ACTIVE_LOW flag in
DTS, so set GPIOD_OUT_LOW when get GPIO descriptors, and set value 1 means
output low, set value 0 means output high with gpiod API.
The in-tree DTS files have the right polarity set up already so we can
expect this to "just work"
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20250324-wcd-gpiod-v2-3-773f67ce3b56@nxp.com
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 9079db287f ("ASoC: codecs: wcd9335: Fix missing free of regulator supplies")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f529c91be8 ]
The ISENSE/VSENSE blocks are only powered up when the amplifier
transitions from shutdown to active. This means that if those controls
are flipped on while the amplifier is already playing back audio, they
will have no effect.
Fix this by forcing a power cycle around transitions in those controls.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250406-apple-codec-changes-v5-1-50a00ec850a3@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 63fe298652 upstream.
Driver gets regulator supplies in probe path with
devm_regulator_bulk_get(), so should not call regulator_bulk_free() in
error and remove paths to avoid double free.
Fixes: 216d04139a ("ASoC: codecs: wcd937x: Remove separate handling for vdd-buck supply")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250526-b4-b4-asoc-wcd9395-vdd-px-fixes-v1-3-0b8a2993b7d3@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff0045de4e ]
RPM manipulation in hda_codec_probe_complete()'s error path is
superfluous and leads to RPM usage count underflow if the
build-controls operation fails.
hda_codec_probe_complete() is called in:
1) hda_codec_probe() for all non-HDMI codecs
2) in card->late_probe() for HDMI codecs
Error path for hda_codec_probe() takes care of bus' RPM already.
For 2) if late_probe() fails, ASoC performs card cleanup what
triggers hda_codec_remote() - same treatment is in 1).
Fixes: b5df2a7dca ("ASoC: codecs: Add HD-Audio codec driver")
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20250530141025.2942936-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd50f0e385 ]
IRQ handling was added in commit dae191fb95 ("ASoC: tas2764: Add IRQ
handling") however that same commit masks all interrupts coming from
the chip. Unmask the "main" interrupts so that we can see and
deal with a number of errors including clock, voltage, and current.
Fixes: dae191fb95 ("ASoC: tas2764: Add IRQ handling")
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250406-apple-codec-changes-v5-4-50a00ec850a3@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70ad2e6bd1 ]
The headphone clamps cause fairly loud pops during type detect
because they sink current from the detection process itself. Disable
the clamps whilst the type detect runs, to improve the detection
pop performance.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250423090944.1504538-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9a5c4b6af ]
Add a few missing registers from the readable register callback.
Suggested-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20250107154408.814455-6-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d92a38d67 ]
As per codec device specification, 24-bit is allowed in provider mode.
Update the code to reflect that.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20250203141051.2361323-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c3b5f3740 ]
The ASoC convention is that clocks are removed after codec mute, and
power up/down is more about top level power management. For these chips,
the "mute" state still expects a TDM clock, and yanking the clock in
this state will trigger clock errors. So, do the full
shutdown<->mute<->active transition on the mute operation, so the amp is
in software shutdown by the time the clocks are removed.
This fixes TDM clock errors when streams are stopped.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20250208-asoc-tas2764-v1-1-dbab892a69b5@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0116a7d84b ]
Add a stub for mt6359_accdet_enable_jack_detect() to prevent linker
failures in the machine sound drivers calling it when
CONFIG_SND_SOC_MT6359_ACCDET is not enabled.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patch.msgid.link/20250306-mt8188-accdet-v3-3-7828e835ff4b@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17fdf318f5 ]
The current code for the IRQ in pcm6240 makes no sense:
it looks up an IRQ with of_irq_get(), treat it as a GPIO
by issuing gpio_request(), gpio_direction_input()
and gpio_to_irq() on it.
This is just wrong, if the device tree assigns the IRQ
from a GPIO number this is just incorrect: it is clearly
stated that GPIO providers and IRQ providers are
orthogonal.
It is possible to look up an IRQ to a corresponding GPIO
line but this is taking an IRQ and pretending it's a
GPIO, which is just semantically wrong.
Drop the offending code and treat the IRQ that we get
from the device tree as any other IRQ, see for example
other codec drivers.
The DT bindings for this codec does not have any in-tree
DTS files, which may explain why things are weird.
As a bonus, this moves the driver away from the legacy
<linux/gpio.h> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20250312-pcm-codecs-v1-3-41ffc4f8fc5c@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed3b274abc ]
VI sense port on WSA883x speaker takes only one channel, so use 0x1 as
channel mask. This fixes garbage being recorded by the speaker when
testing the VI sense feedback path.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250312-asoc-wsa88xx-visense-v1-1-9ca705881122@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 060fac202e ]
VI sense port on WSA883x speaker takes only one channel, so use 0x1 as
channel mask. This fixes garbage being recorded by the speaker when
testing the VI sense feedback path.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250312-asoc-wsa88xx-visense-v1-2-9ca705881122@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96014d91cf ]
Depend on SND_SOC_CS_AMP_LIB instead of selecting it.
KUNIT_ALL_TESTS should only build tests for components that are
already being built, it should not cause other stuff to be added
to the build.
Fixes: 177862317a ("ASoC: cs-amp-lib: Add KUnit test for calibration helpers")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250411123608.1676462-3-rf@opensource.cirrus.com
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 060aed9c00 ]
If 'port_id' is negative, the shift counts in wcd934x_slim_irq_handler()
also become negative, resulting in undefined behavior due to shift out
of bounds.
If I'm reading the code correctly, that appears to be not possible, but
with KCOV enabled, Clang's range analysis isn't always able to determine
that and generates undefined behavior.
As a result the code generation isn't optimal, and undefined behavior
should be avoided regardless. Improve code generation and remove the
undefined behavior by converting the signed variables to unsigned.
Fixes the following warning with UBSAN:
sound/soc/codecs/snd-soc-wcd934x.o: warning: objtool: .text.wcd934x_slim_irq_handler: unexpected end of section
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/7e863839ec7301bf9c0f429a03873d44e484c31c.1742852847.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/oe-kbuild-all/202503180044.oH9gyPeg-lkp@intel.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7648beb656 upstream.
Existing code only configures one of WSA_MACRO_TX0 or WSA_MACRO_TX1
paths eventhough we enable both of them. Fix this bug by adding proper
checks and rearranging some of the common code to able to allow setting
both TX0 and TX1 paths
Without this patch only one channel gets enabled in VI path instead of 2
channels. End result would be 1 channel recording instead of 2.
Fixes: 2c4066e5d4 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Cc: stable@vger.kernel.org
Co-developed-by: Manikantan R <quic_manrav@quicinc.com>
Signed-off-by: Manikantan R <quic_manrav@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250403160209.21613-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7bff1415e upstream.
Currently the VI feedback rate is set to fixed 8K, fix this by getting
the correct rate from params_rate.
Without this patch incorrect rate will be set on the VI feedback
recording resulting in rate miss match and audio artifacts.
Fixes: 2c4066e5d4 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250403160209.21613-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fc7d2b5ca ]
Some of the manually selected jack configurations will disable the
headphone clamp override. Restore this on jack removal, such that
the state is consistent for a new insert.
Fixes: fc918cbe87 ("ASoC: cs42l43: Add support for the cs42l43")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250409120717.1294528-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e330acf4e upstream.
When snd_soc_dapm_new_controls() or snd_soc_dapm_add_routes() fails,
wcd937x_soc_codec_probe() returns without releasing 'wcd937x->clsh_info',
which is allocated by wcd_clsh_ctrl_alloc. Add wcd_clsh_ctrl_free()
to prevent potential memory leak.
Fixes: 313e978df7 ("ASoC: codecs: wcd937x: add audio routing and Kconfig")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20250226085050.3584898-1-haoxiang_li2024@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ebd494426 ]
Should an error occur after a successful regulator_bulk_enable() call,
regulator_bulk_disable() should be called, as already done in the remove
function.
Instead of adding an error handling path in the probe, switch from
devm_regulator_bulk_get() to devm_regulator_bulk_get_enable() and
simplify the remove function and some other places accordingly.
Finally, add a missing const when defining rt5665_supply_names to please
checkpatch and constify a few bytes.
Fixes: 33ada14a26 ("ASoC: add rt5665 codec driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/e3c2aa1b2fdfa646752d94f4af968630c0d58248.1742629525.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 927e6bec5c ]
"generic_new_peripheral_assigned: invalid dev_num 1, wake supported 1"
is reported by our internal CI test.
Rt1320's wake feature is not used in Linux and that's why it is not in
the wake_capable_list[] list in intel_auxdevice.c.
However, BIOS may set it as wake-capable. Overwrite wake_capable to 0
in the codec driver to align with wake_capable_list[].
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Shuming Fan <shumingf@realtek.com>
Link: https://patch.msgid.link/20250305134113.201326-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d776f016d2 ]
Temperatures are reported in units of Celsius however hwmon expects
values to be in millidegree of Celsius. Userspace tools observe values
close to zero and report it as "Not available" or incorrect values like
0C or 1C. Add a simple conversion to fix that.
Before the change:
wsa884x-virtual-0
Adapter: Virtual device
temp1: +0.0°C
--
wsa884x-virtual-0
Adapter: Virtual device
temp1: +0.0°C
Also reported as N/A before first amplifier power on.
After this change and initial wsa884x power on:
wsa884x-virtual-0
Adapter: Virtual device
temp1: +39.0°C
--
wsa884x-virtual-0
Adapter: Virtual device
temp1: +37.0°C
Tested on sm8550 only.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20250221044024.1207921-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad5a0970f8 ]
Currently the return value from spi_setup() is not checked for a failure.
It is unlikely it will ever fail in this particular case but it is still
better to add this check for the sake of completeness and correctness. This
is cheap since it is performed once when the device is being probed.
Handle spi_setup() return value.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 872fc0b6bd ("ASoC: cs35l41: Set the max SPI speed for the whole device")
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru>
Link: https://patch.msgid.link/20250304115643.2748-1-v.shevtsov@mt-integration.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed92bc5264 ]
Free some resources in the error handling path of the probe, as already
done in the remove function.
Fixes: e3523e0186 ("ASoC: wm0010: Add initial wm0010 DSP driver")
Fixes: fd8b965744 ("ASoC: wm0010: Clear IRQ as wake source and include missing header")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/5139ba1ab8c4c157ce04e56096a0f54a1683195c.1741549792.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 247fba1341 ]
SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15,
RT722_SDCA_CTL_FU_CH_GAIN, CH_01) ... SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY,
RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_04) are used by the
"FU15 Boost Volume" control, but not marked as readable.
And the mbq size are 2 for those registers.
Fixes: 7f5d6036ca ("ASoC: rt722-sdca: Add RT722 SDCA driver")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://patch.msgid.link/20250310080440.58797-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e26f1cfeac ]
The range of ADC volume is -1 -> 3 (-6 to 18dB) so the number of levels
should actually be 4.
Fixes: fc918cbe87 ("ASoC: cs42l43: Add support for the cs42l43")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250306133254.1861046-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5468beeab ]
TX launch polarity needs to be the opposite of RX capture polarity, to
generate the right bit slot alignment.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250218-apple-codec-changes-v2-28-932760fd7e07@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 579cd64b9d ]
The scale starts at -100dB, not -128dB.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20250208-asoc-tas2770-v1-1-cf50ff1d59a3@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 679074942c ]
Using `fsleep` instead of `msleep` resolves some customer complaints
regarding the precision of up/down DAPM event timing. `fsleep()`
automatically selects the appropriate sleep function, making the delay
time more predictable.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://patch.msgid.link/20250205160849.500306-1-vitalyr@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 769c1b7929 ]
When SPI is used for control, the driver must hold the SPI bus lock
while issuing the sequence of writes to perform a soft reset.
>From the time the driver writes the SYSTEM_RESET command until the
driver does a write to terminate the reset, there must not be any
activity on the SPI bus lines. If there is any SPI activity during the
soft-reset, another soft-reset will be triggered. The state of the SPI
chip select is irrelevant.
A repeated soft-reset does not in itself cause any problems, and it is
not an infinite loop. The problem is a race between these resets and
the driver polling for boot completion. There is a time window between
soft resets where the driver could read HALO_STATE as 2 (fully booted)
while the chip is actually soft-resetting. Although this window is
small, it is long enough that it is possible to hit it in normal
operation.
To prevent this race and ensure the chip really is fully booted, the
driver calls spi_bus_lock() to prevent other activity while resetting.
It then issues the SYSTEM_RESET mailbox command. After allowing
sufficient time for reset to take effect, the driver issues a PING
mailbox command, which will force completion of the full soft-reset
sequence. The SPI bus lock can then be released. The mailbox is
checked for any boot or wakeup response from the firmware, before the
value in HALO_STATE will be trusted.
This does not affect SoundWire or I2C control.
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250225131843.113752-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b0c02f9b8 ]
The ES8328 codec driver, which is also used for the ES8388 chip that
appears to have an identical register map, claims that the output can
either take the route from DAC->Mixer->Output or through DAC->Output
directly. To the best of what I could find, this is not true, and
creates problems.
Without DACCONTROL17 bit index 7 set for the left channel, as well as
DACCONTROL20 bit index 7 set for the right channel, I cannot get any
analog audio out on Left Out 2 and Right Out 2 respectively, despite the
DAPM routes claiming that this should be possible. Furthermore, the same
is the case for Left Out 1 and Right Out 1, showing that those two don't
have a direct route from DAC to output bypassing the mixer either.
Those control bits toggle whether the DACs are fed (stale bread?) into
their respective mixers. If one "unmutes" the mixer controls in
alsamixer, then sure, the audio output works, but if it doesn't work
without the mixer being fed the DAC input then evidently it's not a
direct output from the DAC.
ES8328/ES8388 are seemingly not alone in this. ES8323, which uses a
separate driver for what appears to be a very similar register map,
simply flips those two bits on in its probe function, and then pretends
there is no power management whatsoever for the individual controls.
Fair enough.
My theory as to why nobody has noticed this up to this point is that
everyone just assumes it's their fault when they had to unmute an
additional control in ALSA.
Fix this in the es8328 driver by removing the erroneous direct route,
then get rid of the playback switch controls and have those bits tied to
the mixer's widget instead, which until now had no register to play
with.
Fixes: 567e4f9892 ("ASoC: add es8328 codec driver")
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://patch.msgid.link/20250222-es8328-route-bludgeoning-v1-1-99bfb7fb22d9@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 582057d223 ]
We should use *-y instead of *-objs in Makefile for the module
objects. *-objs is used rather for host programs.
Fixes: 313e978df7 ("ASoC: codecs: wcd937x: add audio routing and Kconfig")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241203141823.22393-6-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f0b8d367d ]
We should use *-y instead of *-objs in Makefile for the module
objects. *-objs is used rather for host programs.
Fixes: c486def5b3 ("ASoC: cs40l50: Support I2S streaming to CS40L50")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241203141823.22393-2-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f0defd2e5 ]
This ensures codec will resume after suspending during playback.
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250109093822.5745-1-mstrozek@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85c9ac7a56 ]
For 48Mhz MCLK systems the calculation of the HW rate is broken,
and will not produce even one sane rate. Since es83xx supports
the option to halve MCLK, calculate also rates with MCLK/2.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://patch.msgid.link/20241227202751.244954-1-posteuca@mutex.one
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9e3ebdc52 ]
The calibration procedure needs some time to finish.
This patch adds the delay time to ensure the calibration procedure is completed correctly.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://patch.msgid.link/20241218091307.96656-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
