commit a7ed7b9d0e upstream.
On arm64, it has been possible for a module's sections to be placed more
than 128M away from each other since commit:
commit 3e35d303ab ("arm64: module: rework module VA range selection")
Due to this, an ftrace callsite in a module's .init.text section can be
out of branch range for the module's ftrace PLT entry (in the module's
.text section). Any attempt to enable tracing of that callsite will
result in a BRK being patched into the callsite, resulting in a fatal
exception when the callsite is later executed.
Fix this by adding an additional trampoline for .init.text, which will
be within range.
No additional trampolines are necessary due to the way a given
module's executable sections are packed together. Any executable
section beginning with ".init" will be placed in MOD_INIT_TEXT,
and any other executable section, including those beginning with ".exit",
will be placed in MOD_TEXT.
Fixes: 3e35d303ab ("arm64: module: rework module VA range selection")
Cc: <stable@vger.kernel.org> # 6.5.x
Signed-off-by: panfan <panfan@qti.qualcomm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20250905032236.3220885-1-panfan@qti.qualcomm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8073330629 ]
Add missing microSD slot vqmmc-supply property, otherwise the kernel
might shut down LDO5 regulator and that would power off the microSD
card slot, possibly while it is in use. Add the property to make sure
the kernel is aware of the LDO5 regulator which supplies the microSD
slot and keeps the LDO5 enabled.
Fixes: 562d222f23 ("arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c53cf8ce3b ]
Add missing microSD slot vqmmc-supply property, otherwise the kernel
might shut down LDO5 regulator and that would power off the microSD
card slot, possibly while it is in use. Add the property to make sure
the kernel is aware of the LDO5 regulator which supplies the microSD
slot and keeps the LDO5 enabled.
Fixes: 8d6712695b ("arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5245dc5ff9 ]
Fix SD card removal caused by automatic LDO5 power off after boot:
LDO5: disabling
mmc1: card 59b4 removed
EXT4-fs (mmcblk1p2): shut down requested (2)
Aborting journal on device mmcblk1p2-8.
JBD2: I/O error when updating journal superblock for mmcblk1p2-8.
To prevent this, add vqmmc regulator for USDHC, using a GPIO-controlled
regulator that is supplied by LDO5. Since this is implemented on SoM but
used on baseboards with SD-card interface, implement the functionality
on SoM part and optionally enable it on baseboards if needed.
Fixes: 418d1d840e ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1f9c49761 ]
As described in the pinebookpro_v2.1_mainboard_schematic.pdf page 10,
he SPI Flash's VCC connector is connected to VCC_3V0 power source.
This fixes the following warning:
spi-nor spi1.0: supply vcc not found, using dummy regulator
Fixes: 5a65505a69 ("arm64: dts: rockchip: Add initial support for Pinebook Pro")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250730102129.224468-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0b8da0415 ]
This moves pinmux child nodes for sdhci0 node from k3-am62x-sk-common
to each top level board file. This is needed since we require internal
pullups for AM62x SK and not for AM62 LP SK since it has external
pullups on DATA 1-7.
Internal pulls are required for AM62 SK as per JESD84 spec
recommendation to prevent unconnected lines floating.
Fixes: d19a66ae48 ("arm64: dts: ti: k3-am625-sk: Enable on board peripherals")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250707190830.3951619-1-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef839ba814 ]
Remove disable-wp flag for eMMC nodes since this flag is
only applicable to SD according to the binding doc
(mmc/mmc-controller-common.yaml).
For eMMC, this flag should be ignored but lets remove
anyways to cleanup sdhci nodes.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://lore.kernel.org/r/20250429151454.4160506-4-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: a0b8da0415 ("arm64: dts: ti: k3-am62*: Move eMMC pinmux to top level board file")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db3cd905b8 ]
The bootph-all flag was introduced in dt-schema
(dtschema/schemas/bootph.yaml) to define node usage across
different boot phases.
For eMMC and SD boot modes, voltage regulator nodes, io-expander
nodes, gpio nodes, and MMC nodes need to be present in all boot
stages, so add missing bootph-all phase flag to these nodes to
support SD boot and eMMC boot.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://lore.kernel.org/r/20250429151454.4160506-2-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: a0b8da0415 ("arm64: dts: ti: k3-am62*: Move eMMC pinmux to top level board file")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e44ac61ab upstream.
main_uart1 reserved for TIFS firmware traces is routed to the
onboard FT4232 via a FET switch which is connected to pin A21 and
B21 of the SoC and not E17 and C17. Fix it.
Fixes: cf39ff15cc ("arm64: dts: ti: k3-am62a7-sk: Describe main_uart1 and wkup_uart")
Cc: stable@vger.kernel.org
Signed-off-by: Hong Guan <hguan@ti.com>
[bb@ti.com: expanded commit message]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250707-uart-fixes-v1-1-8164147218b0@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4292564c71 upstream.
ufs-exynos driver configures the sysreg shareability as
cacheable for gs101 so we need to set the dma-coherent
property so the descriptors are also allocated cacheable.
This fixes the UFS stability issues we have seen with
the upstream UFS driver on gs101.
Fixes: 4c65d7054b ("arm64: dts: exynos: gs101: Add ufs and ufs-phy dt nodes")
Cc: stable@vger.kernel.org
Suggested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Tested-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250314-ufs-dma-coherent-v1-1-bdf9f9be2919@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b27212788 upstream.
Switch Schmitt Trigger functions for PIN_INPUT* macros by default. This is
HW PoR configuration, the slew rate requirements without ST enabled are
pretty tough for these devices. We've noticed spurious GPIO interrupts even
with noise-free edges but not meeting slew rate requirements (3.3E+6 V/s
for 3.3v LVCMOS).
It's not obvious why one might want to disable the PoR-enabled ST on any
pin. Just enable it by default. As it's not possible to provide OR-able
macros to disable the ST, shall anyone require it, provide a set of
new macros with _NOST suffix.
Fixes: fe49f2d776 ("arm64: dts: ti: Use local header for pinctrl register values")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20250701105437.3539924-1-alexander.sverdlin@siemens.com
[vigneshr@ti.com: Add Fixes tag]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65ba2a6e77 ]
According to the "GPIO Expander Map / Table" section of the J722S EVM
Schematic within the Evaluation Module Design Files package [0], the
GPIO Pin P05 located on the GPIO Expander 1 (I2C0/0x23) has to be pulled
down to select the Type-C interface. Since commit under Fixes claims to
enable the Type-C interface, update the property within "p05-hog" from
"output-high" to "output-low", thereby switching from the Type-A
interface to the Type-C interface.
[0]: https://www.ti.com/lit/zip/sprr495
Cc: stable@vger.kernel.org
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250623100657.4082031-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc8d9e6b58 ]
J722S SOC has two usb controllers USB0 and USB1. USB0 is brought out on
the EVM as a stacked USB connector which has one Type-A and one Type-C
port. These Type-A and Type-C ports are connected to MUX so only
one of them can be enabled at a time.
Commit under Fixes, tries to enable the USB0 instance of USB to
interface with the Type-C port via the USB hub, by configuring the
USB2.0_MUX_SEL to GPIO_ACTIVE_HIGH. But it is observed on J722S-EVM
that Type-A port is enabled instead of Type-C port.
Fix this by setting USB2.0_MUX_SEL to GPIO_ACTIVE_LOW to enable Type-C
port.
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20250116125726.2549489-1-h-salunke@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Stable-dep-of: 65ba2a6e77 ("arm64: dts: ti: k3-j722s-evm: Fix USB gpio-hog level for Type-C")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59305202c6 upstream.
Memory hot remove unmaps and tears down various kernel page table regions
as required. The ptdump code can race with concurrent modifications of
the kernel page tables. When leaf entries are modified concurrently, the
dump code may log stale or inconsistent information for a VA range, but
this is otherwise not harmful.
But when intermediate levels of kernel page table are freed, the dump code
will continue to use memory that has been freed and potentially
reallocated for another purpose. In such cases, the ptdump code may
dereference bogus addresses, leading to a number of potential problems.
To avoid the above mentioned race condition, platforms such as arm64,
riscv and s390 take memory hotplug lock, while dumping kernel page table
via the sysfs interface /sys/kernel/debug/kernel_page_tables.
Similar race condition exists while checking for pages that might have
been marked W+X via /sys/kernel/debug/kernel_page_tables/check_wx_pages
which in turn calls ptdump_check_wx(). Instead of solving this race
condition again, let's just move the memory hotplug lock inside generic
ptdump_check_wx() which will benefit both the scenarios.
Drop get_online_mems() and put_online_mems() combination from all existing
platform ptdump code paths.
Link: https://lkml.kernel.org/r/20250620052427.2092093-1-anshuman.khandual@arm.com
Fixes: bbd6ec605c ("arm64/mm: Enable memory hot remove")
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dev Jain <dev.jain@arm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> [s390]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit beecfd6a88 ]
If kretprobe_find_ret_addr() fails to find the original return address,
it returns 0. Check for this case so that a reliable stacktrace won't
silently ignore it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Andrea della Porta <andrea.porta@suse.com>
Cc: Breno Leitao <leitao@debian.org>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Song Liu <song@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-and-tested-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20250521111000.2237470-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bad3fa2fb9 ]
The kernel currently alway prints:
"Use ACPI SPCR as default console: No/Yes "
even on systems that lack an SPCR table. This can
mislead users into thinking the SPCR table exists
on the machines without SPCR.
With this change, the "Yes" is only printed if
the SPCR table is present, parsed and !param_acpi_nospcr.
This avoids user confusion on SPCR-less systems.
Signed-off-by: Li Chen <chenl311@chinatelecom.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20250620131309.126555-3-me@linux.beauty
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7ce7e3a84 ]
Set TAINT_MACHINE_CHECK when SError or Synchronous External Abort (SEA)
interrupts trigger a panic to flag potential hardware faults. This
tainting mechanism aids in debugging and enables correlation of
hardware-related crashes in large-scale deployments.
This change aligns with similar patches[1] that mark machine check
events when the system crashes due to hardware errors.
Link: https://lore.kernel.org/all/20250702-add_tain-v1-1-9187b10914b9@debian.org/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20250716-vmcore_hw_error-v2-1-f187f7d62aba@debian.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65c430906e ]
GCC appears to have kind of fragile inlining heuristics, in the
sense that it can change whether or not it inlines something based on
optimizations. It looks like the kcov instrumentation being added (or in
this case, removed) from a function changes the optimization results,
and some functions marked "inline" are _not_ inlined. In that case,
we end up with __init code calling a function not marked __init, and we
get the build warnings I'm trying to eliminate in the coming patch that
adds __no_sanitize_coverage to __init functions:
WARNING: modpost: vmlinux: section mismatch in reference: acpi_get_enable_method+0x1c (section: .text.unlikely) -> acpi_psci_present (section: .init.text)
This problem is somewhat fragile (though using either __always_inline
or __init will deterministically solve it), but we've tripped over
this before with GCC and the solution has usually been to just use
__always_inline and move on.
For arm64 this requires forcing one ACPI function to be inlined with
__always_inline.
Link: https://lore.kernel.org/r/20250724055029.3623499-1-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b114fcee76 ]
In the ARM64 BPF JIT when prog->aux->exception_boundary is set for a BPF
program, find_used_callee_regs() is not called because for a program
acting as exception boundary, all callee saved registers are saved.
find_used_callee_regs() sets `ctx->fp_used = true;` when it sees FP
being used in any of the instructions.
For programs acting as exception boundary, ctx->fp_used remains false
even if frame pointer is used by the program and therefore, FP is not
set-up for such programs in the prologue. This can cause the kernel to
crash due to a pagefault.
Fix it by setting ctx->fp_used = true for exception boundary programs as
fp is always saved in such programs.
Fixes: 5d4fa9ec56 ("bpf, arm64: Avoid blindly saving/restoring all callee-saved registers")
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/bpf/20250722133410.54161-2-puranjay@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16ad6c799 ]
The reference manual for the i.MX8MN states the clock rate in
MMC mode is 1/2 of the input clock, therefore to properly run
at HS400 rates, the input clock must be 400MHz to operate at
200MHz. Currently the clock is set to 200MHz which is half the
rate it should be, so the throughput is half of what it should be
for HS400 operation.
Fixes: 36ca3c8ccb ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f83f69097a ]
The reference manual for the i.MX8MM states the clock rate in
MMC mode is 1/2 of the input clock, therefore to properly run
at HS400 rates, the input clock must be 400MHz to operate at
200MHz. Currently the clock is set to 200MHz which is half the
rate it should be, so the throughput is half of what it should be
for HS400 operation.
Fixes: 593816fa2f ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ec406ac4b ]
Remove always-on on generic ARM timer as the clock source provided by
STGEN is deactivated in low power mode, STOP1 by example.
Fixes: 5d30d03aaf ("arm64: dts: st: introduce stm32mp25 SoCs family")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250515151238.1.I85271ddb811a7cf73532fec90de7281cb24ce260@changeid
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdc8ad019a ]
Pinmux registers ends at 0x000f42ac (including). Thus, the size argument
of the pinctrl-single node has to be 0x2b0. Fix it.
This will fix the following error:
pinctrl-single f4000.pinctrl: mux offset out of range: 0x2ac (0x2ac)
Fixes: 29075cc09f ("arm64: dts: ti: Introduce AM62P5 family of SoCs")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20250618065239.1904953-1-mwalle@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 945e48a39c ]
For the ICSSG PHYs to operate correctly, a 25 MHz reference clock must
be supplied on CLKOUT0. Previously, our bootloader configured this
clock, which is why the PRU Ethernet ports appeared to work, but the
change never made it into the device tree.
Add clock properties to make EXT_REFCLK1.CLKOUT0 output a 25MHz clock.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Fixes: 87adfd1ab0 ("arm64: dts: ti: am642-phyboard-electra: Add PRU-ICSSG nodes")
Link: https://lore.kernel.org/r/20250521053339.1751844-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76270a18db ]
The blsp_dma controller is shared between the different subsystems,
which is why it is already initialized by the firmware. We should not
reinitialize it from Linux to avoid potential other users of the DMA
engine to misbehave.
In mainline this can be described using the "qcom,controlled-remotely"
property. In the downstream/vendor kernel from Qualcomm there is an
opposite "qcom,managed-locally" property. This property is *not* set
for the qcom,sps-dma@7884000 and qcom,sps-dma@7ac4000 [1] so adding
"qcom,controlled-remotely" upstream matches the behavior of the
downstream/vendor kernel.
Adding this fixes booting Longcheer L9360.
[1]: https://git.codelinaro.org/clo/la/kernel/msm-3.10/-/blob/LA.BR.1.3.7.c26/arch/arm/boot/dts/qcom/msm8976.dtsi#L1149-1163
Fixes: 0484d3ce09 ("arm64: dts: qcom: Add DTS for MSM8976 and MSM8956 SoCs")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Link: https://lore.kernel.org/r/20250615-bqx5plus-v2-1-72b45c84237d@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b649082312 ]
In preparation for switching to the architected timer as the primary
clockevents device, mark the cpuidle nodes with the 'local-timer-stop'
property to indicate that an alternative clockevents device must be
used for waking up from the "c2" idle state.
Signed-off-by: Will Deacon <willdeacon@google.com>
[Original commit from https://android.googlesource.com/kernel/gs/+/a896fd98638047989513d05556faebd28a62b27c]
Signed-off-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Youngmin Nam <youngmin.nam@samsung.com>
Tested-by: Youngmin Nam <youngmin.nam@samsung.com>
Fixes: ea89fdf24f ("arm64: dts: exynos: google: Add initial Google gs101 SoC support")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250611-gs101-cpuidle-v2-1-4fa811ec404d@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 965e28cad4 ]
We need more than what is currently described, expand the region to its
actual boundaries.
Fixes: ede638c42c ("arm64: dts: qcom: sc7180: Add IMEM and pil info regions")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250523-topic-ipa_mem_dts-v1-3-f7aa94fac1ab@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81a4a7de3d ]
We need more than what is currently described, expand the region to its
actual boundaries.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Fixes: 948f6161c6 ("arm64: dts: qcom: sdm845: Add IMEM and PIL info region")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250523-topic-ipa_mem_dts-v1-2-f7aa94fac1ab@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 696a4c325f ]
TQMa9352 is only using LPDDR4X, so the BUCK2 regulator should be fixed
at 600MV.
Fixes: d2858e6bd3 ("arm64: dts: freescale: imx93-tqma9352: Add PMIC node")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ce920e6a8 ]
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org
Fixes: bd50b1f5b6 ("arm64: dts: qcom: x1e80100: Add Compute Reference Device")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-1-24b6a2043025@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
[ Change x1e80100-crd.dts instead ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 673fa129e5 ]
The l12b and l15b supplies are used by components that are not (fully)
described (and some never will be) and must never be disabled.
Mark the regulators as always-on to prevent them from being disabled,
for example, when consumers probe defer or suspend.
Fixes: 7d1cbe2f49 ("arm64: dts: qcom: Add X1E78100 ThinkPad T14s Gen 6")
Cc: stable@vger.kernel.org # 6.12
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250314145440.11371-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
[ applied changes to .dts file instead of .dtsi ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d42e6c20de upstream.
`cpu_switch_to()` and `call_on_irq_stack()` manipulate SP to change
to different stacks along with the Shadow Call Stack if it is enabled.
Those two stack changes cannot be done atomically and both functions
can be interrupted by SErrors or Debug Exceptions which, though unlikely,
is very much broken : if interrupted, we can end up with mismatched stacks
and Shadow Call Stack leading to clobbered stacks.
In `cpu_switch_to()`, it can happen when SP_EL0 points to the new task,
but x18 stills points to the old task's SCS. When the interrupt handler
tries to save the task's SCS pointer, it will save the old task
SCS pointer (x18) into the new task struct (pointed to by SP_EL0),
clobbering it.
In `call_on_irq_stack()`, it can happen when switching from the task stack
to the IRQ stack and when switching back. In both cases, we can be
interrupted when the SCS pointer points to the IRQ SCS, but SP points to
the task stack. The nested interrupt handler pushes its return addresses
on the IRQ SCS. It then detects that SP points to the task stack,
calls `call_on_irq_stack()` and clobbers the task SCS pointer with
the IRQ SCS pointer, which it will also use !
This leads to tasks returning to addresses on the wrong SCS,
or even on the IRQ SCS, triggering kernel panics via CONFIG_VMAP_STACK
or FPAC if enabled.
This is possible on a default config, but unlikely.
However, when enabling CONFIG_ARM64_PSEUDO_NMI, DAIF is unmasked and
instead the GIC is responsible for filtering what interrupts the CPU
should receive based on priority.
Given the goal of emulating NMIs, pseudo-NMIs can be received by the CPU
even in `cpu_switch_to()` and `call_on_irq_stack()`, possibly *very*
frequently depending on the system configuration and workload, leading
to unpredictable kernel panics.
Completely mask DAIF in `cpu_switch_to()` and restore it when returning.
Do the same in `call_on_irq_stack()`, but restore and mask around
the branch.
Mask DAIF even if CONFIG_SHADOW_CALL_STACK is not enabled for consistency
of behaviour between all configurations.
Introduce and use an assembly macro for saving and masking DAIF,
as the existing one saves but only masks IF.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ada Couprie Diaz <ada.coupriediaz@arm.com>
Reported-by: Cristian Prundeanu <cpru@amazon.com>
Fixes: 59b37fe52f ("arm64: Stash shadow stack pointer in the task struct on interrupt")
Tested-by: Cristian Prundeanu <cpru@amazon.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20250718142814.133329-1-ada.coupriediaz@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61f1065272 ]
Correct the DMA interrupter number of pcie0_ep from 317 to 311.
Fixes: 3b1d5deb29 ("arm64: dts: imx95: add pcie[0,1] and pcie-ep[0,1] support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98570e8cb8 ]
cd-gpios is used for sdcard detects for sdmmc.
Fixes: 3f5d336d64 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250524064223.5741-2-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e625e28417 ]
cd-gpios is used for sdcard detects for sdmmc.
Fixes: 791c154c39 ("arm64: dts: rockchip: Add support for rk3588 based board Cool Pi CM5 EVB")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250524064223.5741-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 53b6445ad0 upstream.
Hardware CS has a very slow rise time of about 6us,
causing transmission errors when CS does not reach
high between transaction.
It looks like it's not driven actively when transitioning
from low to high but switched to input, so only the CPU
pull-up pulls it high, slowly. Transitions from high to low
are fast. On the oscilloscope, CS looks like an irregular sawtooth
pattern like this:
_____
^ / |
^ /| / |
/| / | / |
/ | / | / |
___/ |___/ |_____/ |___
With cs-gpios we have a CS rise time of about 20ns, as it should be,
and CS looks rectangular.
This fixes the data errors when running a flashcp loop against a
m25p40 spi flash.
With the Rockchip 6.1 kernel we see the same slow rise time, but
for some reason CS is always high for long enough to reach a solid
high.
The RK3399 and RK3588 SoCs use the same SPI driver, so we also
checked our "Puma" (RK3399) and "Tiger" (RK3588) boards.
They do not have this problem. Hardware CS rise time is good.
Fixes: c484cf93f6 ("arm64: dts: rockchip: add PX30-µQ7 (Ringneck) SoM with Haikou baseboard")
Cc: stable@vger.kernel.org
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@cherry.de>
Link: https://lore.kernel.org/r/20250627131715.1074308-1-jakob.unterwurzacher@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fc02c2086 upstream.
The IMX8MPDS Table 37 [1] shows that the max SPI master read frequency
depends on the pins the interface is muxed behind with ECSPI2
muxed behind ECSPI2 supporting up to 25MHz.
Adjust the spi-max-frequency based on these findings.
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MPIEC
Fixes: 2b3ab9d81a ("arm64: dts: imx8mp-venice-gw73xx: add TPM device")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b25344753c upstream.
The IMX8MPDS Table 37 [1] shows that the max SPI master read frequency
depends on the pins the interface is muxed behind with ECSPI2
muxed behind ECSPI2 supporting up to 25MHz.
Adjust the spi-max-frequency based on these findings.
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MPIEC
Fixes: 5016f22028 ("arm64: dts: imx8mp-venice-gw72xx: add TPM device")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbe94be09f upstream.
LDO5 regulator is used to power the i.MX8MM NVCC_SD2 I/O supply, that is
used for the SD2 card interface and also for some GPIOs.
When the SD card interface is not enabled the regulator subsystem could
turn off this supply, since it is not used anywhere else, however this
will also remove the power to some other GPIOs, for example one I/O that
is used to power the ethernet phy, leading to a non working ethernet
interface.
[ 31.820515] On-module +V3.3_1.8_SD (LDO5): disabling
[ 31.821761] PMIC_USDHC_VSELECT: disabling
[ 32.764949] fec 30be0000.ethernet end0: Link is Down
Fix this keeping the LDO5 supply always on.
Cc: stable@vger.kernel.org
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Fixes: f5aab0438e ("regulator: pca9450: Fix enable register for LDO5")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 720fd1cbc0 upstream.
Watchdog doesn't work on NXP ls1046ardb board because in commit
7c8ffc5555cb("arm64: dts: layerscape: remove big-endian for mmc nodes"),
it intended to remove the big-endian from mmc node, but the big-endian of
watchdog node is also removed by accident. So, add watchdog big-endian
property back.
In addition, add compatible string fsl,ls1046a-wdt, which allow big-endian
property.
Fixes: 7c8ffc5555 ("arm64: dts: layerscape: remove big-endian for mmc nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bdaca0922 upstream.
The IMX8MPDS Table 37 [1] shows that the max SPI master read frequency
depends on the pins the interface is muxed behind with ECSPI2
muxed behind ECSPI2 supporting up to 25MHz.
Adjust the spi-max-frequency based on these findings.
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MPIEC
Fixes: 531936b218 ("arm64: dts: imx8mp-venice-gw74xx: update to revB PCB")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a75ad2fc76 upstream.
We have a number of hwcaps for various SME subfeatures enumerated via
ID_AA64SMFR0_EL1. Currently we advertise these without cross checking
against the main SME feature, advertised in ID_AA64PFR1_EL1.SME which
means that if the two are out of sync userspace can see a confusing
situation where SME subfeatures are advertised without the base SME
hwcap. This can be readily triggered by using the arm64.nosme override
which only masks out ID_AA64PFR1_EL1.SME, and there have also been
reports of VMMs which do the same thing.
Fix this as we did previously for SVE in 064737920b ("arm64: Filter
out SVE hwcaps when FEAT_SVE isn't implemented") by filtering out the
SME subfeature hwcaps when FEAT_SME is not present.
Fixes: 5e64b862c4 ("arm64/sme: Basic enumeration support")
Reported-by: Yury Khrustalev <yury.khrustalev@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250620-arm64-sme-filter-hwcaps-v1-1-02b9d3c2d8ef@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22f3a4f608 ]
We do not currently issue an ISB after updating POR_EL0 when
context-switching it, for instance. The rationale is that if the old
value of POR_EL0 is more restrictive and causes a fault during
uaccess, the access will be retried [1]. In other words, we are
trading an ISB on every context-switching for the (unlikely)
possibility of a spurious fault. We may also miss faults if the new
value of POR_EL0 is more restrictive, but that's considered
acceptable.
However, as things stand, a spurious Overlay fault results in
uaccess failing right away since it causes fault_from_pkey() to
return true. If an Overlay fault is reported, we therefore need to
double check POR_EL0 against vma_pkey(vma) - this is what
arch_vma_access_permitted() already does.
As it turns out, we already perform that explicit check if no
Overlay fault is reported, and we need to keep that check (see
comment added in fault_from_pkey()). Net result: the Overlay ISS2
bit isn't of much help to decide whether a pkey fault occurred.
Remove the check for the Overlay bit from fault_from_pkey() and
add a comment to try and explain the situation. While at it, also
add a comment to permission_overlay_switch() in case anyone gets
surprised by the lack of ISB.
[1] https://lore.kernel.org/linux-arm-kernel/ZtYNGBrcE-j35fpw@arm.com/
Fixes: 160a8e13de ("arm64: context switch POR_EL0 register")
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Link: https://lore.kernel.org/r/20250619160042.2499290-2-kevin.brodsky@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abf89bc4bb ]
The l12b and l15b supplies are used by components that are not (fully)
described (and some never will be) and must never be disabled.
Mark the regulators as always-on to prevent them from being disabled,
for example, when consumers probe defer or suspend.
Fixes: bd50b1f5b6 ("arm64: dts: qcom: x1e80100: Add Compute Reference Device")
Cc: stable@vger.kernel.org # 6.8
Cc: Abel Vesa <abel.vesa@linaro.org>
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250314145440.11371-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4becd72352 ]
Only two little a520s share the same L2, every a720 has their own L2
cache.
Fixes: d235037799 ("arm64: dts: qcom: add initial SM8650 dtsi")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250405105529.309711-1-mitltlatltl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
