[ Upstream commit f8b4687151 ]
The original code relies on cancel_delayed_work() in otx2_ptp_destroy(),
which does not ensure that the delayed work item synctstamp_work has fully
completed if it was already running. This leads to use-after-free scenarios
where otx2_ptp is deallocated by otx2_ptp_destroy(), while synctstamp_work
remains active and attempts to dereference otx2_ptp in otx2_sync_tstamp().
Furthermore, the synctstamp_work is cyclic, the likelihood of triggering
the bug is nonnegligible.
A typical race condition is illustrated below:
CPU 0 (cleanup) | CPU 1 (delayed work callback)
otx2_remove() |
otx2_ptp_destroy() | otx2_sync_tstamp()
cancel_delayed_work() |
kfree(ptp) |
| ptp = container_of(...); //UAF
| ptp-> //UAF
This is confirmed by a KASAN report:
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0
Write of size 8 at addr ffff88800aa09a18 by task bash/136
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcf/0x610
? __run_timer_base.part.0+0x7d7/0x8c0
kasan_report+0xb8/0xf0
? __run_timer_base.part.0+0x7d7/0x8c0
__run_timer_base.part.0+0x7d7/0x8c0
? __pfx___run_timer_base.part.0+0x10/0x10
? __pfx_read_tsc+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
run_timer_softirq+0xd1/0x190
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
Allocated by task 1:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
otx2_ptp_init+0xb1/0x860
otx2_probe+0x4eb/0xc30
local_pci_probe+0xdc/0x190
pci_device_probe+0x2fe/0x470
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__driver_attach+0xd2/0x310
bus_for_each_dev+0xed/0x170
bus_add_driver+0x208/0x500
driver_register+0x132/0x460
do_one_initcall+0x89/0x300
kernel_init_freeable+0x40d/0x720
kernel_init+0x1a/0x150
ret_from_fork+0x10c/0x1a0
ret_from_fork_asm+0x1a/0x30
Freed by task 136:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x3f/0x50
kfree+0x137/0x370
otx2_ptp_destroy+0x38/0x80
otx2_remove+0x10d/0x4c0
pci_device_remove+0xa6/0x1d0
device_release_driver_internal+0xf8/0x210
pci_stop_bus_device+0x105/0x150
pci_stop_and_remove_bus_device_locked+0x15/0x30
remove_store+0xcc/0xe0
kernfs_fop_write_iter+0x2c3/0x440
vfs_write+0x871/0xd70
ksys_write+0xee/0x1c0
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the delayed work item is properly canceled before the otx2_ptp is
deallocated.
This bug was initially identified through static analysis. To reproduce
and test it, I simulated the OcteonTX2 PCI device in QEMU and introduced
artificial delays within the otx2_sync_tstamp() function to increase the
likelihood of triggering the bug.
Fixes: 2958d17a89 ("octeontx2-pf: Add support for ptp 1-step mode on CN10K silicon")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfa7d9b1e3 ]
The original code uses cancel_delayed_work() in cnic_cm_stop_bnx2x_hw(),
which does not guarantee that the delayed work item 'delete_task' has
fully completed if it was already running. Additionally, the delayed work
item is cyclic, the flush_workqueue() in cnic_cm_stop_bnx2x_hw() only
blocks and waits for work items that were already queued to the
workqueue prior to its invocation. Any work items submitted after
flush_workqueue() is called are not included in the set of tasks that the
flush operation awaits. This means that after the cyclic work items have
finished executing, a delayed work item may still exist in the workqueue.
This leads to use-after-free scenarios where the cnic_dev is deallocated
by cnic_free_dev(), while delete_task remains active and attempt to
dereference cnic_dev in cnic_delete_task().
A typical race condition is illustrated below:
CPU 0 (cleanup) | CPU 1 (delayed work callback)
cnic_netdev_event() |
cnic_stop_hw() | cnic_delete_task()
cnic_cm_stop_bnx2x_hw() | ...
cancel_delayed_work() | /* the queue_delayed_work()
flush_workqueue() | executes after flush_workqueue()*/
| queue_delayed_work()
cnic_free_dev(dev)//free | cnic_delete_task() //new instance
| dev = cp->dev; //use
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the cyclic delayed work item is properly canceled and that any
ongoing execution of the work item completes before the cnic_dev is
deallocated. Furthermore, since cancel_delayed_work_sync() uses
__flush_work(work, true) to synchronously wait for any currently
executing instance of the work item to finish, the flush_workqueue()
becomes redundant and should be removed.
This bug was identified through static analysis. To reproduce the issue
and validate the fix, I simulated the cnic PCI device in QEMU and
introduced intentional delays — such as inserting calls to ssleep()
within the cnic_delete_task() function — to increase the likelihood
of triggering the bug.
Fixes: fdf24086f4 ("cnic: Defer iscsi connection cleanup")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cca7b1cfd7 ]
The expression `(conf->instr_type == 64) << iq_no` can overflow because
`iq_no` may be as high as 64 (`CN23XX_MAX_RINGS_PER_PF`). Casting the
operand to `u64` ensures correct 64-bit arithmetic.
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Alexey Nepomnyashih <sdl@nppct.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fbfe251cc ]
This reverts commit d24341740f.
It causes errors when trying to configure QoS, as well as
loss of L2 connectivity (on multi-host devices).
Reported-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/20250910170011.70528106@kernel.org
Fixes: d24341740f ("net/mlx5e: Update and set Xon/Xoff upon port speed set")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a72175c985 ]
Currently, VF MAC address info is not updated when the MAC address is
configured from VF, and it is not cleared when the VF is removed. This
leads to stale or missing MAC information in the PF, which may cause
incorrect state tracking or inconsistencies when VFs are hot-plugged
or reassigned.
Fix this by:
- storing the VF MAC address in the PF when it is set from VF
- clearing the stored VF MAC address when the VF is removed
This ensures that the PF always has correct VF MAC state.
Fixes: cde29af9e6 ("octeon_ep: add PF-VF mailbox communication")
Signed-off-by: Sathesh B Edara <sedara@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250916133207.21737-1-sedara@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b4be64fd9 ]
The function mlx5_uplink_netdev_get() gets the uplink netdevice
pointer from mdev->mlx5e_res.uplink_netdev. However, the netdevice can
be removed and its pointer cleared when unbound from the mlx5_core.eth
driver. This results in a NULL pointer, causing a kernel panic.
BUG: unable to handle page fault for address: 0000000000001300
at RIP: 0010:mlx5e_vport_rep_load+0x22a/0x270 [mlx5_core]
Call Trace:
<TASK>
mlx5_esw_offloads_rep_load+0x68/0xe0 [mlx5_core]
esw_offloads_enable+0x593/0x910 [mlx5_core]
mlx5_eswitch_enable_locked+0x341/0x420 [mlx5_core]
mlx5_devlink_eswitch_mode_set+0x17e/0x3a0 [mlx5_core]
devlink_nl_eswitch_set_doit+0x60/0xd0
genl_family_rcv_msg_doit+0xe0/0x130
genl_rcv_msg+0x183/0x290
netlink_rcv_skb+0x4b/0xf0
genl_rcv+0x24/0x40
netlink_unicast+0x255/0x380
netlink_sendmsg+0x1f3/0x420
__sock_sendmsg+0x38/0x60
__sys_sendto+0x119/0x180
do_syscall_64+0x53/0x1d0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Ensure the pointer is valid before use by checking it for NULL. If it
is valid, immediately call netdev_hold() to take a reference, and
preventing the netdevice from being freed while it is in use.
Fixes: 7a9fb35e8c ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1757939074-617281-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e37084a260 ]
i40e has a feature which writes to memory location last descriptor
successfully sent. Memory barrier in i40e_clean_tx_irq() was used to
avoid forward-reading descriptor fields in case DD bit was not set.
Having mentioned feature in place implies that such situation will not
happen as we know in advance how many descriptors HW has dealt with.
Besides, this barrier placement was wrong. Idea is to have this
protection *after* reading DD bit from HW descriptor, not before.
Digging through git history showed me that indeed barrier was before DD
bit check, anyways the commit introducing i40e_get_head() should have
wiped it out altogether.
Also, there was one commit doing s/read_barrier_depends/smp_rmb when get
head feature was already in place, but it was only theoretical based on
ixgbe experiences, which is different in these terms as that driver has
to read DD bit from HW descriptor.
Fixes: 1943d8ba95 ("i40e/i40evf: enable hardware feature head write back")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84bf1ac85a ]
The ice_put_rx_mbuf() function handles calling ice_put_rx_buf() for each
buffer in the current frame. This function was introduced as part of
handling multi-buffer XDP support in the ice driver.
It works by iterating over the buffers from first_desc up to 1 plus the
total number of fragments in the frame, cached from before the XDP program
was executed.
If the hardware posts a descriptor with a size of 0, the logic used in
ice_put_rx_mbuf() breaks. Such descriptors get skipped and don't get added
as fragments in ice_add_xdp_frag. Since the buffer isn't counted as a
fragment, we do not iterate over it in ice_put_rx_mbuf(), and thus we don't
call ice_put_rx_buf().
Because we don't call ice_put_rx_buf(), we don't attempt to re-use the
page or free it. This leaves a stale page in the ring, as we don't
increment next_to_alloc.
The ice_reuse_rx_page() assumes that the next_to_alloc has been incremented
properly, and that it always points to a buffer with a NULL page. Since
this function doesn't check, it will happily recycle a page over the top
of the next_to_alloc buffer, losing track of the old page.
Note that this leak only occurs for multi-buffer frames. The
ice_put_rx_mbuf() function always handles at least one buffer, so a
single-buffer frame will always get handled correctly. It is not clear
precisely why the hardware hands us descriptors with a size of 0 sometimes,
but it happens somewhat regularly with "jumbo frames" used by 9K MTU.
To fix ice_put_rx_mbuf(), we need to make sure to call ice_put_rx_buf() on
all buffers between first_desc and next_to_clean. Borrow the logic of a
similar function in i40e used for this same purpose. Use the same logic
also in ice_get_pgcnts().
Instead of iterating over just the number of fragments, use a loop which
iterates until the current index reaches to the next_to_clean element just
past the current frame. Unlike i40e, the ice_put_rx_mbuf() function does
call ice_put_rx_buf() on the last buffer of the frame indicating the end of
packet.
For non-linear (multi-buffer) frames, we need to take care when adjusting
the pagecnt_bias. An XDP program might release fragments from the tail of
the frame, in which case that fragment page is already released. Only
update the pagecnt_bias for the first descriptor and fragments still
remaining post-XDP program. Take care to only access the shared info for
fragmented buffers, as this avoids a significant cache miss.
The xdp_xmit value only needs to be updated if an XDP program is run, and
only once per packet. Drop the xdp_xmit pointer argument from
ice_put_rx_mbuf(). Instead, set xdp_xmit in the ice_clean_rx_irq() function
directly. This avoids needing to pass the argument and avoids an extra
bit-wise OR for each buffer in the frame.
Move the increment of the ntc local variable to ensure its updated *before*
all calls to ice_get_pgcnts() or ice_put_rx_mbuf(), as the loop logic
requires the index of the element just after the current frame.
Now that we use an index pointer in the ring to identify the packet, we no
longer need to track or cache the number of fragments in the rx_ring.
Cc: Christoph Petrausch <christoph.petrausch@deepl.com>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Reported-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Closes: https://lore.kernel.org/netdev/CAK8fFZ4hY6GUJNENz3wY9jaYLZXGfpr7dnZxzGMYoE44caRbgw@mail.gmail.com/
Fixes: 743bbd93cf ("ice: put Rx buffers after being done with current frame")
Tested-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Tested-by: Priya Singh <priyax.singh@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e61c89c60 ]
The max_frame and rx_buf_len fields of the VSI set the maximum frame size
for packets on the wire, and configure the size of the Rx buffer. In the
hardware, these are per-queue configuration. Most VSI types use a simple
method to determine the size of the buffers for all queues.
However, VFs may potentially configure different values for each queue.
While the Linux iAVF driver does not do this, it is allowed by the virtchnl
interface.
The current virtchnl code simply sets the per-VSI fields inbetween calls to
ice_vsi_cfg_single_rxq(). This technically works, as these fields are only
ever used when programming the Rx ring, and otherwise not checked again.
However, it is confusing to maintain.
The Rx ring also already has an rx_buf_len field in order to access the
buffer length in the hotpath. It also has extra unused bytes in the ring
structure which we can make use of to store the maximum frame size.
Drop the VSI max_frame and rx_buf_len fields. Add max_frame to the Rx ring,
and slightly re-order rx_buf_len to better fit into the gaps in the
structure layout.
Change the ice_vsi_cfg_frame_size function so that it writes to the ring
fields. Call this function once per ring in ice_vsi_cfg_rxqs(). This is
done over calling it inside the ice_vsi_cfg_rxq(), because
ice_vsi_cfg_rxq() is called in the virtchnl flow where the max_frame and
rx_buf_len have already been configured.
Change the accesses for rx_buf_len and max_frame to all point to the ring
structure. This has the added benefit that ice_vsi_cfg_rxq() no longer has
the surprise side effect of updating ring->rx_buf_len based on the VSI
field.
Update the virtchnl ice_vc_cfg_qs_msg() function to set the ring values
directly, and drop references to the removed VSI fields.
This now makes the VF logic clear, as the ring fields are obviously
per-queue. This reduces the required cognitive load when reasoning about
this logic.
Note that removing the VSI fields does leave a 4 byte gap, but the ice_vsi
structure has many gaps, and its layout is not as critical in the hot path.
The structure may benefit from a more thorough repacking, but no attempt
was made in this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 84bf1ac85a ("ice: fix Rx page leak on multi-buffer frames")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93ab4881a4 ]
`netif_rx()` already increments `rx_dropped` core stat when it fails.
The driver was also updating `ndev->stats.rx_dropped` in the same path.
Since both are reported together via `ip -s -s` command, this resulted
in drops being counted twice in user-visible stats.
Keep the driver update on `if (unlikely(!skb))`, but skip it after
`netif_rx()` errors.
Fixes: caf586e5f2 ("net: add a core netdev->rx_dropped counter")
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250913060135.35282-3-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56c0a2a9dd ]
In the protection override dump path, the firmware can return far too
many GRC elements, resulting in attempting to write past the end of the
previously-kmalloc'ed dump buffer.
This will result in a kernel panic with reason:
BUG: unable to handle kernel paging request at ADDRESS
where "ADDRESS" is just past the end of the protection override dump
buffer. The start address of the buffer is:
p_hwfn->cdev->dbg_features[DBG_FEATURE_PROTECTION_OVERRIDE].dump_buf
and the size of the buffer is buf_size in the same data structure.
The panic can be arrived at from either the qede Ethernet driver path:
[exception RIP: qed_grc_dump_addr_range+0x108]
qed_protection_override_dump at ffffffffc02662ed [qed]
qed_dbg_protection_override_dump at ffffffffc0267792 [qed]
qed_dbg_feature at ffffffffc026aa8f [qed]
qed_dbg_all_data at ffffffffc026b211 [qed]
qed_fw_fatal_reporter_dump at ffffffffc027298a [qed]
devlink_health_do_dump at ffffffff82497f61
devlink_health_report at ffffffff8249cf29
qed_report_fatal_error at ffffffffc0272baf [qed]
qede_sp_task at ffffffffc045ed32 [qede]
process_one_work at ffffffff81d19783
or the qedf storage driver path:
[exception RIP: qed_grc_dump_addr_range+0x108]
qed_protection_override_dump at ffffffffc068b2ed [qed]
qed_dbg_protection_override_dump at ffffffffc068c792 [qed]
qed_dbg_feature at ffffffffc068fa8f [qed]
qed_dbg_all_data at ffffffffc0690211 [qed]
qed_fw_fatal_reporter_dump at ffffffffc069798a [qed]
devlink_health_do_dump at ffffffff8aa95e51
devlink_health_report at ffffffff8aa9ae19
qed_report_fatal_error at ffffffffc0697baf [qed]
qed_hw_err_notify at ffffffffc06d32d7 [qed]
qed_spq_post at ffffffffc06b1011 [qed]
qed_fcoe_destroy_conn at ffffffffc06b2e91 [qed]
qedf_cleanup_fcport at ffffffffc05e7597 [qedf]
qedf_rport_event_handler at ffffffffc05e7bf7 [qedf]
fc_rport_work at ffffffffc02da715 [libfc]
process_one_work at ffffffff8a319663
Resolve this by clamping the firmware's return value to the maximum
number of legal elements the firmware should return.
Fixes: d52c89f120 ("qed*: Utilize FW 8.37.2.0")
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Link: https://patch.msgid.link/f8e1182934aa274c18d0682a12dbaf347595469c.1757485536.git.jamie.bainbridge@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2690cb0895 ]
Starting with commit c50e747596 ("dpaa2-switch: Fix error checking in
dpaa2_switch_seed_bp()"), the probing of a second DPSW object errors out
like below.
fsl_dpaa2_switch dpsw.1: fsl_mc_driver_probe failed: -12
fsl_dpaa2_switch dpsw.1: probe with driver fsl_dpaa2_switch failed with error -12
The aforementioned commit brought to the surface the fact that seeding
buffers into the buffer pool destined for control traffic is not
successful and an access violation recoverable error can be seen in the
MC firmware log:
[E, qbman_rec_isr:391, QBMAN] QBMAN recoverable event 0x1000000
This happens because the driver incorrectly used the ID of the DPBP
object instead of the hardware buffer pool ID when trying to release
buffers into it.
This is because any DPSW object uses two buffer pools, one managed by
the Linux driver and destined for control traffic packet buffers and the
other one managed by the MC firmware and destined only for offloaded
traffic. And since the buffer pool managed by the MC firmware does not
have an external facing DPBP equivalent, any subsequent DPBP objects
created after the first DPSW will have a DPBP id different to the
underlying hardware buffer ID.
The issue was not caught earlier because these two numbers can be
identical when all DPBP objects are created before the DPSW objects are.
This is the case when the DPL file is used to describe the entire DPAA2
object layout and objects are created at boot time and it's also true
for the first DPSW being created dynamically using ls-addsw.
Fix this by using the buffer pool ID instead of the DPBP id when
releasing buffers into the pool.
Fixes: 2877e4f7e1 ("staging: dpaa2-switch: setup buffer pool and RX path rings")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20250910144825.2416019-1-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 915470e1b4 ]
If request_irq() in i40e_vsi_request_irq_msix() fails in an iteration
later than the first, the error path wants to free the IRQs requested
so far. However, it uses the wrong dev_id argument for free_irq(), so
it does not free the IRQs correctly and instead triggers the warning:
Trying to free already-free IRQ 173
WARNING: CPU: 25 PID: 1091 at kernel/irq/manage.c:1829 __free_irq+0x192/0x2c0
Modules linked in: i40e(+) [...]
CPU: 25 UID: 0 PID: 1091 Comm: NetworkManager Not tainted 6.17.0-rc1+ #1 PREEMPT(lazy)
Hardware name: [...]
RIP: 0010:__free_irq+0x192/0x2c0
[...]
Call Trace:
<TASK>
free_irq+0x32/0x70
i40e_vsi_request_irq_msix.cold+0x63/0x8b [i40e]
i40e_vsi_request_irq+0x79/0x80 [i40e]
i40e_vsi_open+0x21f/0x2f0 [i40e]
i40e_open+0x63/0x130 [i40e]
__dev_open+0xfc/0x210
__dev_change_flags+0x1fc/0x240
netif_change_flags+0x27/0x70
do_setlink.isra.0+0x341/0xc70
rtnl_newlink+0x468/0x860
rtnetlink_rcv_msg+0x375/0x450
netlink_rcv_skb+0x5c/0x110
netlink_unicast+0x288/0x3c0
netlink_sendmsg+0x20d/0x430
____sys_sendmsg+0x3a2/0x3d0
___sys_sendmsg+0x99/0xe0
__sys_sendmsg+0x8a/0xf0
do_syscall_64+0x82/0x2c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
</TASK>
---[ end trace 0000000000000000 ]---
Use the same dev_id for free_irq() as for request_irq().
I tested this with inserting code to fail intentionally.
Fixes: 493fb30011 ("i40e: Move q_vectors from pointer to array to array of pointers")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d709f178ab ]
The igb driver incorrectly skips the link test when the network
interface is admin down (if_running == false), causing the test to
always report PASS regardless of the actual physical link state.
This behavior is inconsistent with other drivers (e.g. i40e, ice, ixgbe,
etc.) which correctly test the physical link state regardless of admin
state.
Remove the if_running check to ensure link test always reflects the
physical link state.
Fixes: 8d420a1b3e ("igb: correct link test not being run when link is down")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03e79de460 ]
The function of_phy_find_device may return NULL, so we need to take
care before dereferencing phy_dev.
Fixes: 64a632da53 ("net: fec: Fix phy_device lookup for phy_reset_after_clk_enable()")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250904091334.53965-1-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1ce840c7a6 upstream.
Currently, when firmware failure occurs during matcher disconnect flow,
the error flow of the function reconnects the matcher back and returns
an error, which continues running the calling function and eventually
frees the matcher that is being disconnected.
This leads to a case where we have a freed matcher on the matchers list,
which in turn leads to use-after-free and eventual crash.
This patch fixes that by not trying to reconnect the matcher back when
some FW command fails during disconnect.
Note that we're dealing here with FW error. We can't overcome this
problem. This might lead to bad steering state (e.g. wrong connection
between matchers), and will also lead to resource leakage, as it is
the case with any other error handling during resource destruction.
However, the goal here is to allow the driver to continue and not crash
the machine with use-after-free error.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250102181415.1477316-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jan Alexander Preissler <akendo@akendo.eu>
Signed-off-by: Sujana Subramaniam <sujana.subramaniam@sap.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca47c44d36 upstream.
Add missing IDs for LAN8651 devices, which are also defined in the
DT bindings.
Fixes: 5cd2340cb6 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable@kernel.org
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250827115341.34608-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7217963eb upstream.
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from spi_device_id table. While at this, fix
the misleading variable name (spidev is unrelated to this driver).
Fixes: 5cd2340cb6 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable@kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250827115341.34608-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90fb7db49c upstream.
Fix a possible heap overflow in e1000_set_eeprom function by adding
input validation for the requested length of the change in the EEPROM.
In addition, change the variable type from int to size_t for better
code practices and rearrange declarations to RCT.
Cc: stable@vger.kernel.org
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Co-developed-by: Mikael Wessel <post@mikaelkw.online>
Signed-off-by: Mikael Wessel <post@mikaelkw.online>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3852ae310 upstream.
There is no guarantee that spi_setup succeed, so properly handle
the error case.
Fixes: aa58bec064 ("net: ethernet: oa_tc6: implement register write operation")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable@kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250827115341.34608-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8bbceba7dc ]
Add proper error checking for dmaengine_desc_get_metadata_ptr() which
can return an error pointer and lead to potential crashes or undefined
behaviour if the pointer retrieval fails.
Properly handle the error by unmapping DMA buffer, freeing the skb and
returning early to prevent further processing with invalid data.
Fixes: 6a91b846af ("net: axienet: Introduce dmaengine support")
Signed-off-by: Abin Joseph <abin.joseph@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://patch.msgid.link/20250903025213.3120181-1-abin.joseph@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e3d71a92e ]
All paths in probe that call goto defer do so before assigning phydev
and thus it makes sense to cleanup the prior index. It also fixes a bug
where index 0 does not get cleaned up.
Fixes: b7d3e3d3d2 ("net: thunderx: Don't leak phy device references on -EPROBE_DEFER condition.")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250901213314.48599-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d473673711 ]
When sending llc packets with vlan tx offload, the hardware fails to
actually add the tag. Deal with this by fixing it up in software.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Reported-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250831182007.51619-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7e5c3e3bf ]
incorrectly used ixgbe_lp_map in loops intended to populate the
supported and advertised EEE linkmode bitmaps based on ixgbe_ls_map.
This results in incorrect bit setting and potential out-of-bounds
access, since ixgbe_lp_map and ixgbe_ls_map have different sizes
and purposes.
ixgbe_lp_map[i] -> ixgbe_ls_map[i]
Use ixgbe_ls_map for supported and advertised linkmodes, and keep
ixgbe_lp_map usage only for link partner (lp_advertised) mapping.
Fixes: 9356b6db9d ("net: ethernet: ixgbe: Convert EEE to use linkmodes")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a556f06338 ]
list_first_entry() never returns NULL - if the list is empty, it still
returns a pointer to an invalid object, leading to potential invalid
memory access when dereferenced.
Fix this by using list_first_entry_or_null instead of list_first_entry.
Fixes: e3219ce6a7 ("i40e: Add support for client interface for IWARP driver")
Signed-off-by: Zhen Ni <zhen.ni@easystack.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fcdb1c3c4 ]
The 'command' and 'netdev_ops' debugfs files are a legacy debugging
interface supported by the i40e driver since its early days by commit
02e9c29081 ("i40e: debugfs interface").
Both of these debugfs files provide a read handler which is mostly useless,
and which is implemented with questionable logic. They both use a static
256 byte buffer which is initialized to the empty string. In the case of
the 'command' file this buffer is literally never used and simply wastes
space. In the case of the 'netdev_ops' file, the last command written is
saved here.
On read, the files contents are presented as the name of the device
followed by a colon and then the contents of their respective static
buffer. For 'command' this will always be "<device>: ". For 'netdev_ops',
this will be "<device>: <last command written>". But note the buffer is
shared between all devices operated by this module. At best, it is mostly
meaningless information, and at worse it could be accessed simultaneously
as there doesn't appear to be any locking mechanism.
We have also recently received multiple reports for both read functions
about their use of snprintf and potential overflow that could result in
reading arbitrary kernel memory. For the 'command' file, this is definitely
impossible, since the static buffer is always zero and never written to.
For the 'netdev_ops' file, it does appear to be possible, if the user
carefully crafts the command input, it will be copied into the buffer,
which could be large enough to cause snprintf to truncate, which then
causes the copy_to_user to read beyond the length of the buffer allocated
by kzalloc.
A minimal fix would be to replace snprintf() with scnprintf() which would
cap the return to the number of bytes written, preventing an overflow. A
more involved fix would be to drop the mostly useless static buffers,
saving 512 bytes and modifying the read functions to stop needing those as
input.
Instead, lets just completely drop the read access to these files. These
are debug interfaces exposed as part of debugfs, and I don't believe that
dropping read access will break any script, as the provided output is
pretty useless. You can find the netdev name through other more standard
interfaces, and the 'netdev_ops' interface can easily result in garbage if
you issue simultaneous writes to multiple devices at once.
In order to properly remove the i40e_dbg_netdev_ops_buf, we need to
refactor its write function to avoid using the static buffer. Instead, use
the same logic as the i40e_dbg_command_write, with an allocated buffer.
Update the code to use this instead of the static buffer, and ensure we
free the buffer on exit. This fixes simultaneous writes to 'netdev_ops' on
multiple devices, and allows us to remove the now unused static buffer
along with removing the read access.
Fixes: 02e9c29081 ("i40e: debugfs interface")
Reported-by: Kunwu Chan <chentao@kylinos.cn>
Closes: https://lore.kernel.org/intel-wired-lan/20231208031950.47410-1-chentao@kylinos.cn/
Reported-by: Wang Haoran <haoranwangsec@gmail.com>
Closes: https://lore.kernel.org/all/CANZ3JQRRiOdtfQJoP9QM=6LS1Jto8PGBGw6y7-TL=BcnzHQn1Q@mail.gmail.com/
Reported-by: Amir Mohammad Jahangirzad <a.jahangirzad@gmail.com>
Closes: https://lore.kernel.org/all/20250722115017.206969-1-a.jahangirzad@gmail.com/
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kunwu Chan <kunwu.chan@linux.dev>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acf3a5c8be ]
On control planes that allow changing the MAC address of the interface,
the driver must provide a MAC type to avoid errors such as:
idpf 0000:0a:00.0: Transaction failed (op 535)
idpf 0000:0a:00.0: Received invalid MAC filter payload (op 535) (len 0)
idpf 0000:0a:00.0: Transaction failed (op 536)
These errors occur during driver load or when changing the MAC via:
ip link set <iface> address <mac>
Add logic to set the MAC type when sending ADD/DEL (opcodes 535/536) to
the control plane. Since only one primary MAC is supported per vport, the
driver only needs to send an ADD opcode when setting it. Remove the old
address by calling __idpf_del_mac_filter(), which skips the message and
just clears the entry from the internal list. This avoids an error on DEL
as it attempts to remove an address already cleared by the preceding ADD
opcode.
Fixes: ce1b75d063 ("idpf: add ptypes and MAC filter support")
Reported-by: Jian Liu <jianliu@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6486338fd ]
Recent versions of the E810 firmware have support for an extra interrupt to
handle report of the "low latency" Tx timestamps coming from the
specialized low latency firmware interface. Instead of polling the
registers, software can wait until the low latency interrupt is fired.
This logic makes use of the Tx timestamp tracking structure, ice_ptp_tx, as
it uses the same "ready" bitmap to track which Tx timestamps complete.
Unfortunately, the ice_ll_ts_intr() function does not check if the
tracker is initialized before its first access. This results in NULL
dereference or use-after-free bugs similar to the issues fixed in the
ice_ptp_ts_irq() function.
Fix this by only checking the in_use bitmap (and other fields) if the
tracker is marked as initialized. The reset flow will clear the init field
under lock before it tears the tracker down, thus preventing any
use-after-free or NULL access.
Fixes: 82e71b226e ("ice: Enable SW interrupt from FW for LL TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bc8a5098b ]
macb_start_xmit and macb_tx_poll can be called with bottom-halves
disabled (e.g. from softirq) as well as with interrupts disabled (with
netpoll). Because of this, all other functions taking tx_ptr_lock must
use spin_lock_irqsave.
Fixes: 138badbc21 ("net: macb: use NAPI for TX completion path")
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250829143521.1686062-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7000f4fa9b ]
The warning in bnxt_alloc_one_rx_ring_netmem() reports the number
of pages allocated for the RX aggregation ring. However, it
mistakenly used bp->rx_ring_size instead of bp->rx_agg_ring_size,
leading to confusing or misleading log output.
Use the correct bp->rx_agg_ring_size value to fix this.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://patch.msgid.link/20250830062331.783783-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b79e498080 ]
The current code incorrectly passes (XIRCREG1_ECR | FullDuplex) as
the register address to GetByte(), instead of fetching the register
value and OR-ing it with FullDuplex. This results in an invalid
register access.
Fix it by reading XIRCREG1_ECR first, then or-ing with FullDuplex
before writing it back.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250827192645.658496-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dac978e51c ]
When the driver is removed the clocks are disabled twice: once in
macb_remove and a second time by runtime pm. Disable wakeup in remove so
all the clocks are disabled and skip the second call to macb_clks_disable.
Always suspend the device as we always set it active in probe.
Fixes: d54f89af6c ("net: macb: Add pm runtime support")
Signed-off-by: Neil Mandir <neil.mandir@seco.com>
Co-developed-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250826143022.935521-1-sean.anderson@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ede14a2c6 ]
The fbnic driver was presenting with the following locking assert coming
out of a PM resume:
[ 42.208116][ T164] RTNL: assertion failed at drivers/net/phy/phylink.c (2611)
[ 42.208492][ T164] WARNING: CPU: 1 PID: 164 at drivers/net/phy/phylink.c:2611 phylink_resume+0x190/0x1e0
[ 42.208872][ T164] Modules linked in:
[ 42.209140][ T164] CPU: 1 UID: 0 PID: 164 Comm: bash Not tainted 6.17.0-rc2-virtme #134 PREEMPT(full)
[ 42.209496][ T164] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-5.fc42 04/01/2014
[ 42.209861][ T164] RIP: 0010:phylink_resume+0x190/0x1e0
[ 42.210057][ T164] Code: 83 e5 01 0f 85 b0 fe ff ff c6 05 1c cd 3e 02 01 90 ba 33 0a 00 00 48 c7 c6 20 3a 1d a5 48 c7 c7 e0 3e 1d a5 e8 21 b8 90 fe 90 <0f> 0b 90 90 e9 86 fe ff ff e8 42 ea 1f ff e9 e2 fe ff ff 48 89 ef
[ 42.210708][ T164] RSP: 0018:ffffc90000affbd8 EFLAGS: 00010296
[ 42.210983][ T164] RAX: 0000000000000000 RBX: ffff8880078d8400 RCX: 0000000000000000
[ 42.211235][ T164] RDX: 0000000000000000 RSI: 1ffffffff4f10938 RDI: 0000000000000001
[ 42.211466][ T164] RBP: 0000000000000000 R08: ffffffffa2ae79ea R09: fffffbfff4b3eb84
[ 42.211707][ T164] R10: 0000000000000003 R11: 0000000000000000 R12: ffff888007ad8000
[ 42.211997][ T164] R13: 0000000000000002 R14: ffff888006a18800 R15: ffffffffa34c59e0
[ 42.212234][ T164] FS: 00007f0dc8e39740(0000) GS:ffff88808f51f000(0000) knlGS:0000000000000000
[ 42.212505][ T164] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 42.212704][ T164] CR2: 00007f0dc8e9fe10 CR3: 000000000b56d003 CR4: 0000000000772ef0
[ 42.213227][ T164] PKRU: 55555554
[ 42.213366][ T164] Call Trace:
[ 42.213483][ T164] <TASK>
[ 42.213565][ T164] __fbnic_pm_attach.isra.0+0x8e/0xa0
[ 42.213725][ T164] pci_reset_function+0x116/0x1d0
[ 42.213895][ T164] reset_store+0xa0/0x100
[ 42.214025][ T164] ? pci_dev_reset_attr_is_visible+0x50/0x50
[ 42.214221][ T164] ? sysfs_file_kobj+0xc1/0x1e0
[ 42.214374][ T164] ? sysfs_kf_write+0x65/0x160
[ 42.214526][ T164] kernfs_fop_write_iter+0x2f8/0x4c0
[ 42.214677][ T164] ? kernfs_vma_page_mkwrite+0x1f0/0x1f0
[ 42.214836][ T164] new_sync_write+0x308/0x6f0
[ 42.214987][ T164] ? __lock_acquire+0x34c/0x740
[ 42.215135][ T164] ? new_sync_read+0x6f0/0x6f0
[ 42.215288][ T164] ? lock_acquire.part.0+0xbc/0x260
[ 42.215440][ T164] ? ksys_write+0xff/0x200
[ 42.215590][ T164] ? perf_trace_sched_switch+0x6d0/0x6d0
[ 42.215742][ T164] vfs_write+0x65e/0xbb0
[ 42.215876][ T164] ksys_write+0xff/0x200
[ 42.215994][ T164] ? __ia32_sys_read+0xc0/0xc0
[ 42.216141][ T164] ? do_user_addr_fault+0x269/0x9f0
[ 42.216292][ T164] ? rcu_is_watching+0x15/0xd0
[ 42.216442][ T164] do_syscall_64+0xbb/0x360
[ 42.216591][ T164] entry_SYSCALL_64_after_hwframe+0x4b/0x53
[ 42.216784][ T164] RIP: 0033:0x7f0dc8ea9986
A bit of digging showed that we were invoking the phylink_resume as a part
of the fbnic_up path when we were enabling the service task while not
holding the RTNL lock. We should be enabling this sooner as a part of the
ndo_open path and then just letting the service task come online later.
This will help to enforce the correct locking and brings the phylink
interface online at the same time as the network interface, instead of at a
later time.
I tested this on QEMU to verify this was working by putting the system to
sleep using "echo mem > /sys/power/state" to put the system to sleep in the
guest and then using the command "system_wakeup" in the QEMU monitor.
Fixes: 69684376ee ("eth: fbnic: Add link detection")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/175616257316.1963577.12238158800417771119.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1eded580a ]
Currently, in the AF_XDP transmit paths, the CIC bit of
TX Desc3 is set for all packets. Setting this bit for
packets transmitting through queues that don't support
checksum offloading causes the TX DMA to get stuck after
transmitting some packets. This patch ensures the CIC bit
of TX Desc3 is set only if the TX queue supports checksum
offloading.
Fixes: 132c32ee5b ("net: stmmac: Add TX via XDP zero-copy socket")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-3-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42ef11b2bf ]
Correct supported speed modes as per the XGMAC databook.
Commit 9cb54af214 ("net: stmmac: Fix IP-cores specific
MAC capabilities") removes support for 10M, 100M and
1000HD. 1000HD is not supported by XGMAC IP, but it does
support 10M and 100M FD mode for XGMAC version >= 2_20,
and it also supports 10M and 100M HD mode if the HDSEL bit
is set in the MAC_HW_FEATURE0 reg. This commit enables support
for 10M and 100M speed modes for XGMAC IP based on XGMAC
version and MAC capabilities.
Fixes: 9cb54af214 ("net: stmmac: Fix IP-cores specific MAC capabilities")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-2-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f23382841 ]
Enabling RX FIFO Overflow interrupts is counterproductive
and causes an interrupt storm when RX FIFO overflows.
Disabling this interrupt has no side effect and eliminates
interrupt storms when the RX FIFO overflows.
Commit 8a7cb245cf ("net: stmmac: Do not enable RX FIFO
overflow interrupts") disables RX FIFO overflow interrupts
for DWMAC4 IP and removes the corresponding handling of
this interrupt. This patch is doing the same thing for
XGMAC IP.
Fixes: 2142754f8b ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250825-xgmac-minor-fixes-v3-1-c225fe4444c0@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aca0c31af6 ]
The local Xoff value is being set before the firmware (FW) update.
In case of a failure where the FW is not updated with the new value,
there is no fallback to the previous value.
Update the local Xoff value after the FW has been successfully set.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-12-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d24341740f ]
Xon/Xoff sizes are derived from calculations that include
the port speed.
These settings need to be updated and applied whenever the
port speed is changed.
The port speed is typically set after the physical link goes down
and is negotiated as part of the link-up process between the two
connected interfaces.
Xon/Xoff parameters being updated at the point where the new
negotiated speed is established.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-11-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceddedc969 ]
Xon/Xoff sizes are derived from calculation that include the MTU size.
Set Xon/Xoff when MTU is set.
If Xon/Xoff fails, set the previous MTU.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-10-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26e42ec771 ]
If PF (Physical Function) has SFs (Sub-Functions), since the SFs are not
taking part in the synchronization flow, sync reset can lead to fatal
error on the SFs, as the function will be closed unexpectedly from the
SF point of view.
Add a check to prevent sync reset when there are SFs on a PF device
which is not ECPF, as ECPF is teardowned gracefully before reset.
Fixes: 92501fa6e4 ("net/mlx5: Ack on sync_reset_request only if PF can do reset_now")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-8-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34cc6a5491 ]
The devlink reload fw_activate command performs firmware activation
followed by driver reload, while devlink reload driver_reinit triggers
only driver reload. However, the driver reload logic differs between the
two modes, as on driver_reinit mode mlx5 also reloads auxiliary drivers,
while in fw_activate mode the auxiliary drivers are suspended where
applicable.
Additionally, following the cited commit, if the device has multiple PFs,
the behavior during fw_activate may vary between PFs: one PF may suspend
auxiliary drivers, while another reloads them.
Align devlink dev reload fw_activate behavior with devlink dev reload
driver_reinit, to reload all auxiliary drivers.
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Akiva Goldberger <agoldberger@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250825143435.598584-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4fc8faacf ]
The HW resource reservation logic allows the L2 driver to use the
RoCE resources if the RoCE driver is not registered. When calculating
the stats contexts available for L2, we should not blindly subtract
the stats contexts reserved for RoCE unless the RoCE driver is
registered. This bug may cause the L2 rings to be less than the
number requested when we are close to running out of stats contexts.
Fixes: 2e4592dc9b ("bnxt_en: Change MSIX/NQs allocation policy")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ee581c24d ]
Before we accept an ethtool request to increase a resource (such as
rings), we call the FW to check that the requested resource is likely
available first before we commit. But it is still possible that
the actual reservation or allocation can fail. The existing code
is missing the logic to adjust the TX rings in case the reserved
TX rings are less than requested. Add a warning message (a similar
message for RX rings already exists) and add the logic to adjust
the TX rings. Without this fix, the number of TX rings reported
to the stack can exceed the actual TX rings and ethtool -l will
report more than the actual TX rings.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2747328ba2 ]
bnxt_set_dflt_rings() assumes that it is always called before any TC has
been created. So it doesn't take bp->num_tc into account and assumes
that it is always 0 or 1.
In the FW resource or capability change scenario, the FW will return
flags in bnxt_hwrm_if_change() that will cause the driver to
reinitialize and call bnxt_cancel_reservations(). This will lead to
bnxt_init_dflt_ring_mode() calling bnxt_set_dflt_rings() and bp->num_tc
may be greater than 1. This will cause bp->tx_ring[] to be sized too
small and cause memory corruption in bnxt_alloc_cp_rings().
Fix it by properly scaling the TX rings by bp->num_tc in the code
paths mentioned above. Add 2 helper functions to determine
bp->tx_nr_rings and bp->tx_nr_rings_per_tc.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250825175927.459987-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 007a5ffadc ]
`McstFramesRcvdOk` counts the number of received multicast packets, and
it reports the value correctly.
However, reading `McstFramesRcvdOk` clears the register to zero. As a
result, the driver was reporting only the packets since the last read,
instead of the accumulated total.
Fix this by updating the multicast statistics accumulatively instaed of
instantaneously.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-on: D-Link DGE-550T Rev-A3
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250823182927.6063-3-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a0c977c6 ]
Currently, the driver increments `alloc_page_failed` when buffer allocation fails
in `ice_clean_rx_irq()`. However, this counter is intended for page allocation
failures, not buffer allocation issues.
This patch corrects the counter by incrementing `alloc_buf_failed` instead,
ensuring accurate statistics reporting for buffer allocation failures.
Fixes: 2fba7dc515 ("ice: Add support for XDP multi-buffer on Rx side")
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Priya Singh <priyax.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c5e5b52bf ]
The ice_adapter structure is used by the ice driver to connect multiple
physical functions of a device in software. It was introduced by
commit 0e2bddf9e5 ("ice: add ice_adapter for shared data across PFs on
the same NIC") and is primarily used for PTP support, as well as for
handling certain cross-PF synchronization.
The original design of ice_adapter used PCI address information to
determine which devices should be connected. This was extended to support
E825C devices by commit fdb7f54700 ("ice: Initial support for E825C
hardware in ice_adapter"), which used the device ID for E825C devices
instead of the PCI address.
Later, commit 0093cb194a ("ice: use DSN instead of PCI BDF for
ice_adapter index") replaced the use of Bus/Device/Function addressing with
use of the device serial number.
E825C devices may appear in "Dual NAC" configuration which has multiple
physical devices tied to the same clock source and which need to use the
same ice_adapter. Unfortunately, each "NAC" has its own NVM which has its
own unique Device Serial Number. Thus, use of the DSN for connecting
ice_adapter does not work properly. It "worked" in the pre-production
systems because the DSN was not initialized on the test NVMs and all the
NACs had the same zero'd serial number.
Since we cannot rely on the DSN, lets fall back to the logic in the
original E825C support which used the device ID. This is safe for E825C
only because of the embedded nature of the device. It isn't a discreet
adapter that can be plugged into an arbitrary system. All E825C devices on
a given system are connected to the same clock source and need to be
configured through the same PTP clock.
To make this separation clear, reserve bit 63 of the 64-bit index values as
a "fixed index" indicator. Always clear this bit when using the device
serial number as an index.
For E825C, use a fixed value defined as the 0x579C E825C backplane device
ID bitwise ORed with the fixed index indicator. This is slightly different
than the original logic of just using the device ID directly. Doing so
prevents a potential issue with systems where only one of the NACs is
connected with an external PHY over SGMII. In that case, one NAC would
have the E825C_SGMII device ID, but the other would not.
Separate the determination of the full 64-bit index from the 32-bit
reduction logic. Provide both ice_adapter_index() and a wrapping
ice_adapter_xa_index() which handles reducing the index to a long on 32-bit
systems. As before, cache the full index value in the adapter structure to
warn about collisions.
This fixes issues with E825C not initializing PTP on both NACs, due to
failure to connect the appropriate devices to the same ice_adapter.
Fixes: 0093cb194a ("ice: use DSN instead of PCI BDF for ice_adapter index")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
