commit 45eae113dc upstream.
This commit addresses a rarely observed endpoint command timeout
which causes kernel panic due to warn when 'panic_on_warn' is enabled
and unnecessary call trace prints when 'panic_on_warn' is disabled.
It is seen during fast software-controlled connect/disconnect testcases.
The following is one such endpoint command timeout that we observed:
1. Connect
=======
->dwc3_thread_interrupt
->dwc3_ep0_interrupt
->configfs_composite_setup
->composite_setup
->usb_ep_queue
->dwc3_gadget_ep0_queue
->__dwc3_gadget_ep0_queue
->__dwc3_ep0_do_control_data
->dwc3_send_gadget_ep_cmd
2. Disconnect
==========
->dwc3_thread_interrupt
->dwc3_gadget_disconnect_interrupt
->dwc3_ep0_reset_state
->dwc3_ep0_end_control_data
->dwc3_send_gadget_ep_cmd
In the issue scenario, in Exynos platforms, we observed that control
transfers for the previous connect have not yet been completed and end
transfer command sent as a part of the disconnect sequence and
processing of USB_ENDPOINT_HALT feature request from the host timeout.
This maybe an expected scenario since the controller is processing EP
commands sent as a part of the previous connect. It maybe better to
remove WARN_ON in all places where device endpoint commands are sent to
avoid unnecessary kernel panic due to warn.
Cc: stable <stable@kernel.org>
Co-developed-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250808125315.1607-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58577118cc upstream.
During a device-initiated disconnect, the End Transfer command resets
the event filter, allowing a new xferNotReady event to be generated
before the controller is fully halted. Processing this late event
incorrectly triggers a Start Transfer, which prevents the controller
from halting and results in a DSTS.DEVCTLHLT bit polling timeout.
Ignore the late xferNotReady event if the controller is already in a
disconnected state.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250807090700.2397190-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 086a0e516f upstream.
Make sure to drop the reference to the dwc3 device taken by
of_find_device_by_node() on probe errors and on driver unbind.
Fixes: 6dd2565989 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93b400f495 upstream.
Make sure to drop the references taken to the child devices by
of_find_device_by_node() during probe on driver unbind.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Cc: stable@vger.kernel.org # 5.2
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20250724091910.21092-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef8abc0ba4 upstream.
Leaving the USB BCR asserted prevents the associated GDSC to turn on. This
blocks any subsequent attempts of probing the device, e.g. after a probe
deferral, with the following showing in the log:
[ 1.332226] usb30_prim_gdsc status stuck at 'off'
Leave the BCR deasserted when exiting the driver to avoid this issue.
Cc: stable <stable@kernel.org>
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250709132900.3408752-1-krishna.kurapati@oss.qualcomm.com
[ adapted to individual clock management instead of bulk clock operations ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 630a1dec3b upstream.
When dwc3_gadget_soft_disconnect() fails, dwc3_suspend_common() keeps
going with the suspend, resulting in a period where the power domain is
off, but the gadget driver remains connected. Within this time frame,
invoking vbus_event_work() will cause an error as it attempts to access
DWC3 registers for endpoint disabling after the power domain has been
completely shut down.
Abort the suspend sequence when dwc3_gadget_suspend() cannot halt the
controller and proceeds with a soft connect.
Fixes: 9f8a67b65a ("usb: dwc3: gadget: fix gadget suspend/resume")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250528100315.2162699-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2372f1caec upstream.
Currently gadget_wakeup() waits for U0 synchronously if it was
called from func_wakeup(), this is because we need to send the
function wakeup command soon after the link is active. And the
call is made synchronous by polling DSTS continuosly for 20000
times in __dwc3_gadget_wakeup(). But it observed that sometimes
the link is not active even after polling 20K times, leading to
remote wakeup failures. Adding a small delay between each poll
helps, but that won't guarantee resolution in future. Hence make
the gadget_wakeup completely asynchronous.
Since multiple interfaces can issue a function wakeup at once,
add a new variable wakeup_pending_funcs which will indicate the
functions that has issued func_wakup, this is represented in a
bitmap format. If the link is in U3, dwc3_gadget_func_wakeup()
will set the bit corresponding to interface_id and bail out.
Once link comes back to U0, linksts_change irq is triggered,
where the function wakeup command is sent based on bitmap.
Cc: stable <stable@kernel.org>
Fixes: 92c08a84b5 ("usb: dwc3: Add function suspend and function wakeup support")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-4-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 461f24bff8 ]
Intel Merrifield SoC uses these endpoints for tracing and they cannot
be re-allocated if being used because the side band flow control signals
are hard wired to certain endpoints:
• 1 High BW Bulk IN (IN#1) (RTIT)
• 1 1KB BW Bulk IN (IN#8) + 1 1KB BW Bulk OUT (Run Control) (OUT#8)
In device mode, since RTIT (EP#1) and EXI/RunControl (EP#8) uses
External Buffer Control (EBC) mode, these endpoints are to be mapped to
EBC mode (to be done by EXI target driver). Additionally TRB for RTIT
and EXI are maintained in STM (System Trace Module) unit and the EXI
target driver will as well configure the TRB location for EP #1 IN
and EP#8 (IN and OUT). Since STM/PTI and EXI hardware blocks manage
these endpoints and interface to OTG3 controller through EBC interface,
there is no need to enable any events (such as XferComplete etc)
for these end points.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eafba02054 ]
Prepare the gadget driver to handle the reserved endpoints that will be
not allocated at the initialisation time.
While at it, add a warning where the NULL endpoint should never happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 38d6e60b6f upstream.
The "reset" GPIO controls the RESET signal to an external, usually
ULPI PHY, chip. The original code path acquires the signal in LOW
state, and then immediately asserts it HIGH again, if the reset
signal defaulted to asserted, there'd be a short "spike" before the
reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found during code inspection.
Also remove the cryptic "toggle ulpi .." comment.
Fixes: ca05b38252 ("usb: dwc3: xilinx: Add gpio-reset support")
Cc: stable <stable@kernel.org>
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250318064518.9320-1-mike.looijmans@topic.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63ccd26cd1 upstream.
The event count is read from register DWC3_GEVNTCOUNT.
There is a check for the count being zero, but not for exceeding the
event buffer length.
Check that event count does not exceed event buffer length,
avoiding an out-of-bounds access when memcpy'ing the event.
Crash log:
Unable to handle kernel paging request at virtual address ffffffc0129be000
pc : __memcpy+0x114/0x180
lr : dwc3_check_event_buf+0xec/0x348
x3 : 0000000000000030 x2 : 000000000000dfc4
x1 : ffffffc0129be000 x0 : ffffff87aad60080
Call trace:
__memcpy+0x114/0x180
dwc3_interrupt+0x24/0x34
Signed-off-by: Frode Isaksen <frode@meta.com>
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250403072907.448524-1-fisaksen@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc5bfc4e16 upstream.
After phy initialization, some phy operations can only be executed while
in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking
phy ops.
Previously the SUSPENDENABLE bits are only set after the controller
initialization, which may not happen right away if there's no gadget
driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits
only when there's mode switching (change in GCTL.PRTCAPDIR).
Fixes: 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init")
Cc: stable <stable@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/633aef0afee7d56d2316f7cc3e1b2a6d518a8cc9.1738280911.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a8c28426 upstream.
There is a frequent timeout during controller enter/exit from halt state
after toggling the run_stop bit by SW. This timeout occurs when
performing frequent role switches between host and device, causing
device enumeration issues due to the timeout. This issue was not present
when USB2 suspend PHY was disabled by passing the SNPS quirks
(snps,dis_u2_susphy_quirk and snps,dis_enblslpm_quirk) from the DTS.
However, there is a requirement to enable USB2 suspend PHY by setting of
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY bits when controller starts
in gadget or host mode results in the timeout issue.
This commit addresses this timeout issue by ensuring that the bits
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
the dwc3_gadget_run_stop sequence and restoring them after the
dwc3_gadget_run_stop sequence is completed.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250201163903.459-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3a9bd247c upstream.
When the system begins to enter suspend mode, dwc3_suspend() is called
by PM suspend. There is a problem that if someone interrupt the system
suspend process between dwc3_suspend() and pm_suspend() of its parent
device, PM suspend will be canceled and attempt to resume suspended
devices so that dwc3_resume() will be called. However, dwc3 and its
parent device (like the power domain or glue driver) may already be
suspended by runtime PM in fact. If this sutiation happened, the
pm_runtime_set_active() in dwc3_resume() will return an error since
parent device was suspended. This can lead to unexpected behavior if
DWC3 proceeds to execute dwc3_resume_common().
EX.
RPM suspend: ... -> dwc3_runtime_suspend()
-> rpm_suspend() of parent device
...
PM suspend: ... -> dwc3_suspend() -> pm_suspend of parent device
^ interrupt, so resume suspended device
... <- dwc3_resume() <-/
^ pm_runtime_set_active() returns error
To prevent the problem, this commit will skip dwc3_resume_common() and
return the error if pm_runtime_set_active() fails.
Fixes: 68c26fe581 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable <stable@kernel.org>
Signed-off-by: Ray Chi <raychi@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250106082240.3822059-1-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66e0ea341a upstream.
Currently, DWC3 driver attempts to acquire the USB power supply only
once during the probe. If the USB power supply is not ready at that
time, the driver simply ignores the failure and continues the probe,
leading to permanent non-functioning of the gadget vbus_draw callback.
Address this problem by delaying the dwc3 driver initialization until
the USB power supply is registered.
Fixes: 6f0764b5ad ("usb: dwc3: add a power supply for current control")
Cc: stable <stable@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250115044548.2701138-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01ea6bf5cb upstream.
Before writing a new value to the register, the old value needs to be
masked out for the new value to be programmed as intended, because at
least in some cases the reset value of that field is 0xf (max value).
At the moment, the dwc3 core initialises the threshold to the maximum
value (0xf), with the option to override it via a DT. No upstream DTs
seem to override it, therefore this commit doesn't change behaviour for
any upstream platform. Nevertheless, the code should be fixed to have
the desired outcome.
Do so.
Fixes: 80caf7d21a ("usb: dwc3: add lpm erratum support")
Cc: stable@vger.kernel.org # 5.10+ (needs adjustment for 5.4)
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209-dwc3-nyet-fix-v2-1-02755683345b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a48f744bef upstream.
When the USB3 PHY is not defined in the Linux device tree, there could
still be a case where there is a USB3 PHY active on the board and enabled
by the first stage bootloader. If serdes clock is being used then the USB
will fail to enumerate devices in 2.0 only mode.
To solve this, make sure that the PIPE clock is deselected whenever the
USB3 PHY is not defined and guarantees that the USB2 only mode will work
in all cases.
Fixes: 9678f3361a ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: stable@vger.kernel.org
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/1733163111-1414816-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4faee0117 upstream.
When unbind and bind the device again, kernel will dump below warning:
[ 173.972130] sysfs: cannot create duplicate filename '/devices/platform/soc/4c010010.usb/software_node'
[ 173.981564] CPU: 2 UID: 0 PID: 536 Comm: sh Not tainted 6.12.0-rc6-06344-g2aed7c4a5c56 #144
[ 173.989923] Hardware name: NXP i.MX95 15X15 board (DT)
[ 173.995062] Call trace:
[ 173.997509] dump_backtrace+0x90/0xe8
[ 174.001196] show_stack+0x18/0x24
[ 174.004524] dump_stack_lvl+0x74/0x8c
[ 174.008198] dump_stack+0x18/0x24
[ 174.011526] sysfs_warn_dup+0x64/0x80
[ 174.015201] sysfs_do_create_link_sd+0xf0/0xf8
[ 174.019656] sysfs_create_link+0x20/0x40
[ 174.023590] software_node_notify+0x90/0x100
[ 174.027872] device_create_managed_software_node+0xec/0x108
...
The '4c010010.usb' device is a platform device created during the initcall
and is never removed, which causes its associated software node to persist
indefinitely.
The existing device_create_managed_software_node() does not provide a
corresponding removal function.
Replace device_create_managed_software_node() with the
device_add_software_node() and device_remove_software_node() pair to ensure
proper addition and removal of software nodes, addressing this issue.
Fixes: a9400f1979 ("usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241126032841.2458338-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7fc65f514 upstream.
The dwc3_request->num_queued_sgs is decremented on completion. If a
partially completed request is handled, then the
dwc3_request->num_queued_sgs no longer reflects the total number of
num_queued_sgs (it would be cleared).
Correctly check the number of request SG entries remained to be prepare
and queued. Failure to do this may cause null pointer dereference when
accessing non-existent SG entry.
Cc: stable@vger.kernel.org
Fixes: c96e6725db ("usb: dwc3: gadget: Correct the logic for queuing sgs")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d07a7c4aa0fcf746cdca0515150dbe5c52000af7.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02a6982b0c upstream.
The check whether the TRB ring is full or empty in dwc3_calc_trbs_left()
is insufficient. It assumes there are active TRBs if there's any request
in the started_list. However, that's not the case for requests with a
large SG list.
That is, if we have a single usb request that requires more TRBs than
the total TRBs in the TRB ring, the queued TRBs will be available when
all the TRBs in the ring are completed. But the request is only
partially completed and remains in the started_list. With the current
logic, the TRB ring is empty, but dwc3_calc_trbs_left() returns 0.
Fix this by additionally checking for the request->num_trbs for active
TRB count.
Cc: stable@vger.kernel.org
Fixes: 51f1954ad8 ("usb: dwc3: gadget: Fix dwc3_calc_trbs_left()")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/708dc62b56b77da1f704cc2ae9b6ddb1f2dbef1f.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61eb055cd3 upstream.
The existing implementation of the TxFIFO resizing logic only supports
scenarios where more than one port RAM is used. However, there is a need
to resize the TxFIFO in USB2.0-only mode where only a single port RAM is
available. This commit introduces the necessary changes to support
TxFIFO resizing in such scenarios by adding a missing check for single
port RAM.
This fix addresses certain platform configurations where the existing
TxFIFO resizing logic does not work properly due to the absence of
support for single port RAM. By adding this missing check, we ensure
that the TxFIFO resizing logic works correctly in all scenarios,
including those with a single port RAM.
Fixes: 9f607a309f ("usb: dwc3: Resize TX FIFOs to meet EP bursting requirements")
Cc: stable@vger.kernel.org # 6.12.x: fad16c82: usb: dwc3: gadget: Refine the logic for resizing Tx FIFOs
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112044807.623-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d2fb074de upstream.
The driver cannot issue the End Transfer command to the SETUP transfer.
Don't clear DWC3_EP_TRANSFER_STARTED flag to make sure that the driver
won't send Start Transfer command again, which can cause no-resource
error. For example this can occur if the host issues a reset to the
device.
Cc: stable@vger.kernel.org
Fixes: 76cb323f80 ("usb: dwc3: ep0: clear all EP0 flags")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d3d618185fd614bb7426352a9fc1199641d3b5f5.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device was already runtime suspended then during system suspend
we cannot access the device registers else it will crash.
Also we cannot access any registers after dwc3_core_exit() on some
platforms so move the dwc3_enable_susphy() call to the top.
Cc: stable@vger.kernel.org # v5.15+
Reported-by: William McVicker <willmcvicker@google.com>
Closes: https://lore.kernel.org/all/ZyVfcUuPq56R2m1Y@google.com
Fixes: 705e3ce37b ("usb: dwc3: core: Fix system suspend on TI AM62 platforms")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241104-am62-lpm-usb-fix-v1-1-e93df73a4f0d@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init"),
system suspend is broken on AM62 TI platforms.
Before that commit, both DWC3_GUSB3PIPECTL_SUSPHY and DWC3_GUSB2PHYCFG_SUSPHY
bits (hence forth called 2 SUSPHY bits) were being set during core
initialization and even during core re-initialization after a system
suspend/resume.
These bits are required to be set for system suspend/resume to work correctly
on AM62 platforms.
Since that commit, the 2 SUSPHY bits are not set for DEVICE/OTG mode if gadget
driver is not loaded and started.
For Host mode, the 2 SUSPHY bits are set before the first system suspend but
get cleared at system resume during core re-init and are never set again.
This patch resovles these two issues by ensuring the 2 SUSPHY bits are set
before system suspend and restored to the original state during system resume.
Cc: stable@vger.kernel.org # v6.9+
Fixes: 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init")
Link: https://lore.kernel.org/all/1519dbe7-73b6-4afc-bfe3-23f4f75d772f@kernel.org/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20241011-am62-lpm-usb-v3-1-562d445625b5@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 programming guide mentions that when operating in USB2.0 speeds,
if GUSB2PHYCFG[6] or GUSB2PHYCFG[8] is set, it must be cleared prior
to issuing commands and may be set again after the command completes.
But currently while issuing EndXfer command without CmdIOC set, we
wait for 1ms after GUSB2PHYCFG is restored. This results in cases
where EndXfer command doesn't get completed and causes SMMU faults
since requests are unmapped afterwards. Hence restore GUSB2PHYCFG
after waiting for EndXfer command completion.
Cc: stable@vger.kernel.org
Fixes: 1d26ba0944 ("usb: dwc3: Wait unconditionally after issuing EndXfer command")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240924093208.2524531-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses an issue where events were being processed when
the controller was in a halted state. To fix this issue by stop
processing the events as the event count was considered stale or
invalid when the controller was halted.
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Cc: stable@kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240916231813.206-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc3_resume_common() returns an error, runtime pm is left in
suspended and disabled state in dwc3_resume(). Since the device
is suspended, its parent devices (like the power domain or glue
driver) could also be suspended and may have released resources
that dwc requires. Consequently, calling dwc3_suspend_common() in
this situation could result in attempts to access unclocked or
unpowered registers.
To prevent these problems, runtime PM should always be re-enabled,
even after failed resume attempts. This ensures that
dwc3_suspend_common() is skipped in such cases.
Fixes: 68c26fe581 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable@vger.kernel.org
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240913232145.3507723-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __get_dwc3_maximum_speed() function returns an enum type which, in
this context here, is basically unsigned int. On error cases, it's
supposed to return USB_SPEED_UNKNOWN, but it was accidentally changed to
return negative error codes in commit f93e96c544 ("usb: dwc3: rtk: use
scoped device node handling to simplify error paths").
There is only one caller and because of the way that the types work out,
returning negative error codes is not a problem. They will be treated
as greater than USB_SPEED_HIGH and ignored as invalid. So this patch
does not affect run time behavior, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/865e56dc-37cc-47b1-8d35-9047ecb1984a@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SS_CON and U3 wakeup need 'ref_clk' on. iMX8MP turn off it while system
sleep, So disable these wakeup source and only enable DP/DM wakeup source
for host mode.
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-3-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 2 software manage quirk properties (xhci-missing-cas-quirk and
xhci-skip-phy-init-quirk) for xhci host.
dwc3 driver have PHY management to cover both device and host mode, so add
xhci-skip-phy-init-quirk to skip PHY management from HCD core.
Cold Attach Status (CAS) bit can't be set at i.MX8MP after resume from
suspend state. So set xhci-missing-cas-quirk.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-2-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here as well, and this also resolves the merge
conflict in:
drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix addresses STAR 9001285599, which only affects DWC_usb3 version
3.20a. The timer value for PM_LC_TIMER in DWC_usb3 3.20a for the Link
ECN changes is incorrect. If the PM TIMER ECN is enabled via GUCTL2[19],
the link compliance test (TD7.21) may fail. If the ECN is not enabled
(GUCTL2[19] = 0), the controller will use the old timer value (5us),
which is still acceptable for the link compliance test. Therefore, clear
GUCTL2[19] to pass the USB link compliance test: TD 7.21.
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240829094502.26502-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When operating in High-Speed, it is observed that DSTS[USBLNKST] doesn't
update link state immediately after receiving the wakeup interrupt. Since
wakeup event handler calls the resume callbacks, there is a chance that
function drivers can perform an ep queue, which in turn tries to perform
remote wakeup from send_gadget_ep_cmd(STARTXFER). This happens because
DSTS[[21:18] wasn't updated to U0 yet, it's observed that the latency of
DSTS can be in order of milli-seconds. Hence avoid calling gadget_wakeup
during startxfer to prevent unnecessarily issuing remote wakeup to host.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: stable@vger.kernel.org
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240828064302.3796315-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() wrapper instead of two calls, which
together with returning directly instead of useless goto, allows to
nicely simplify the probe() function.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-10-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-9-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() wrapper instead of two calls. This
allows also dropping local 'res' variable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-8-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-7-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler. Scoped/cleanup.h coding style
expects variable declaration with initialization, so the
of_get_compatible_child() call has to be moved earlier, before any goto
jumps happen.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-6-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() to make the error paths a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-5-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get_enabled() to drop clock preparing and handling from
error and remove paths. This makes the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-4-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() to make the error paths a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-2-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler. Scoped/cleanup.h coding style
expects variable declaration with initialization, so the
of_get_compatible_child() call has to be moved earlier, before any goto
jumps happen.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-1-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
