Revert commit 9b28ef1e4c which is upstream
commit e1b0fa8639
It causes regression in 6.12.49 stable, no issues in upstream.
Commit 9b28ef1e4c ("usb: xhci: remove option to change a default
ring's TRB cycle bit") introduced a regression in 6.12.49 stable kernel.
The original commit was never intended for stable kernels, but was added
as a dependency for commit a5c98e8b13 ("xhci: dbc: Fix full DbC
transfer ring after several reconnects").
Since this commit is more of an optimization, revert it and solve the
dependecy by modifying one line in xhci_dbc_ring_init(). Specifically,
commit a5c98e8b13 ("xhci: dbc: Fix full DbC transfer ring after
several reconnects") moved function call xhci_initialize_ring_info()
into a separate function. To resolve the dependency, the arguments for
this function call are also reverted.
Closes: https://lore.kernel.org/stable/01b8c8de46251cfaad1329a46b7e3738@stwm.de/
Tested-by: Wolfgang Walter <linux@stwm.de>
Cc: stable@vger.kernel.org # v6.12.49
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47c428fce0 ]
Use "0x%x" format for quirks debug print to clarify it's a hexadecimal
value. Improves readability and consistency with other hex outputs.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Link: https://lore.kernel.org/r/20250603071045.3243699-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5c98e8b13 ]
Pending requests will be flushed on disconnect, and the corresponding
TRBs will be turned into No-op TRBs, which are ignored by the xHC
controller once it starts processing the ring.
If the USB debug cable repeatedly disconnects before ring is started
then the ring will eventually be filled with No-op TRBs.
No new transfers can be queued when the ring is full, and driver will
print the following error message:
"xhci_hcd 0000:00:14.0: failed to queue trbs"
This is a normal case for 'in' transfers where TRBs are always enqueued
in advance, ready to take on incoming data. If no data arrives, and
device is disconnected, then ring dequeue will remain at beginning of
the ring while enqueue points to first free TRB after last cancelled
No-op TRB.
s
Solve this by reinitializing the rings when the debug cable disconnects
and DbC is leaving the configured state.
Clear the whole ring buffer and set enqueue and dequeue to the beginning
of ring, and set cycle bit to its initial state.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 220a0ffde0 ]
Decouple allocation of endpoint ring buffer from initialization
of the buffer, and initialization of endpoint context parts from
from the rest of the contexts.
It allows driver to clear up and reinitialize endpoint rings
after disconnect without reallocating everything.
This is a prerequisite for the next patch that prevents the transfer
ring from filling up with cancelled (no-op) TRBs if a debug cable is
reconnected several times without transferring anything.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a5c98e8b13 ("xhci: dbc: Fix full DbC transfer ring after several reconnects")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1b0fa8639 ]
The TRB cycle bit indicates TRB ownership by the Host Controller (HC) or
Host Controller Driver (HCD). New rings are initialized with 'cycle_state'
equal to one, and all its TRBs' cycle bits are set to zero. When handling
ring expansion, set the source ring cycle bits to the same value as the
destination ring.
Move the cycle bit setting from xhci_segment_alloc() to xhci_link_rings(),
and remove the 'cycle_state' argument from xhci_initialize_ring_info().
The xhci_segment_alloc() function uses kzalloc_node() to allocate segments,
ensuring that all TRB cycle bits are initialized to zero.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a5c98e8b13 ("xhci: dbc: Fix full DbC transfer ring after several reconnects")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f970bd06c ]
Add macro to streamline and standardize the iteration over ring
segment list.
xhci_for_each_ring_seg(): Iterates over the entire ring segment list.
The xhci_free_segments_for_ring() function's while loop has not been
updated to use the new macro. This function has some underlying issues,
and as a result, it will be handled separately in a future patch.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a5c98e8b13 ("xhci: dbc: Fix full DbC transfer ring after several reconnects")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 116e79c679 upstream.
The EP-IN of MIDI2 (altset 1) wasn't initialized in
f_midi2_create_usb_configs() as it's an INT EP unlike others BULK
EPs. But this leaves rather the max packet size unchanged no matter
which speed is used, resulting in the very slow access.
And the wMaxPacketSize values set there look legit for INT EPs, so
let's initialize the MIDI2 EP-IN there for achieving the equivalent
speed as well.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250905133240.20966-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21d8525d2e upstream.
The gadget card driver forgot to call snd_ump_update_group_attrs()
after adding FBs, and this leaves the UMP group attributes
uninitialized. As a result, -ENODEV error is returned at opening a
legacy rawmidi device as an inactive group.
This patch adds the missing call to address the behavior above.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250904153932.13589-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f34bfcc77b upstream.
tcpm_handle_vdm_request delivers messages to the partner altmode or the
cable altmode depending on the SVDM response type, which is incorrect.
The partner or cable should be chosen based on the received message type
instead.
Also add this filter to ADEV_NOTIFY_USB_AND_QUEUE_VDM, which is used when
the Enter Mode command is responded to by a NAK on SOP or SOP' and when
the Exit Mode command is responded to by an ACK on SOP.
Fixes: 7e7877c55e ("usb: typec: tcpm: add alt mode enter/exit/vdm support for sop'")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250821203759.1720841-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d63c83d8e upstream.
Yunseong Kim and the syzbot fuzzer both reported a problem in
RT-enabled kernels caused by the way dummy-hcd mixes interrupt
management and spin-locking. The pattern was:
local_irq_save(flags);
spin_lock(&dum->lock);
...
spin_unlock(&dum->lock);
... // calls usb_gadget_giveback_request()
local_irq_restore(flags);
The code was written this way because usb_gadget_giveback_request()
needs to be called with interrupts disabled and the private lock not
held.
While this pattern works fine in non-RT kernels, it's not good when RT
is enabled. RT kernels handle spinlocks much like mutexes; in particular,
spin_lock() may sleep. But sleeping is not allowed while local
interrupts are disabled.
To fix the problem, rewrite the code to conform to the pattern used
elsewhere in dummy-hcd and other UDC drivers:
spin_lock_irqsave(&dum->lock, flags);
...
spin_unlock(&dum->lock);
usb_gadget_giveback_request(...);
spin_lock(&dum->lock);
...
spin_unlock_irqrestore(&dum->lock, flags);
This approach satisfies the RT requirements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Fixes: b4dbda1a22 ("USB: dummy-hcd: disable interrupts during req->complete")
Reported-by: Yunseong Kim <ysk@kzalloc.com>
Closes: <https://lore.kernel.org/linux-usb/5b337389-73b9-4ee4-a83e-7e82bf5af87a@kzalloc.com/>
Reported-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
Closes: <https://lore.kernel.org/linux-usb/68ac2411.050a0220.37038e.0087.GAE@google.com/>
Tested-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
CC: stable@vger.kernel.org
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/bb192ae2-4eee-48ee-981f-3efdbbd0d8f0@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edcbe06453 upstream.
Suspend-resume cycle test revealed a memory leak in 6.17-rc3
Turns out the slot_id race fix changes accidentally ends up calling
xhci_free_virt_device() with an incorrect vdev parameter.
The vdev variable was reused for temporary purposes right before calling
xhci_free_virt_device().
Fix this by passing the correct vdev parameter.
The slot_id race fix that caused this regression was targeted for stable,
so this needs to be applied there as well.
Fixes: 2eb0337615 ("usb: xhci: Fix slot_id resource race conflict")
Reported-by: David Wang <00107082@163.com>
Closes: https://lore.kernel.org/linux-usb/20250829181354.4450-1-00107082@163.com
Suggested-by: Michal Pecio <michal.pecio@gmail.com>
Suggested-by: David Wang <00107082@163.com>
Cc: stable@vger.kernel.org
Tested-by: David Wang <00107082@163.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45eae113dc upstream.
This commit addresses a rarely observed endpoint command timeout
which causes kernel panic due to warn when 'panic_on_warn' is enabled
and unnecessary call trace prints when 'panic_on_warn' is disabled.
It is seen during fast software-controlled connect/disconnect testcases.
The following is one such endpoint command timeout that we observed:
1. Connect
=======
->dwc3_thread_interrupt
->dwc3_ep0_interrupt
->configfs_composite_setup
->composite_setup
->usb_ep_queue
->dwc3_gadget_ep0_queue
->__dwc3_gadget_ep0_queue
->__dwc3_ep0_do_control_data
->dwc3_send_gadget_ep_cmd
2. Disconnect
==========
->dwc3_thread_interrupt
->dwc3_gadget_disconnect_interrupt
->dwc3_ep0_reset_state
->dwc3_ep0_end_control_data
->dwc3_send_gadget_ep_cmd
In the issue scenario, in Exynos platforms, we observed that control
transfers for the previous connect have not yet been completed and end
transfer command sent as a part of the disconnect sequence and
processing of USB_ENDPOINT_HALT feature request from the host timeout.
This maybe an expected scenario since the controller is processing EP
commands sent as a part of the previous connect. It maybe better to
remove WARN_ON in all places where device endpoint commands are sent to
avoid unnecessary kernel panic due to warn.
Cc: stable <stable@kernel.org>
Co-developed-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250808125315.1607-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58577118cc upstream.
During a device-initiated disconnect, the End Transfer command resets
the event filter, allowing a new xferNotReady event to be generated
before the controller is fully halted. Processing this late event
incorrectly triggers a Start Transfer, which prevents the controller
from halting and results in a DSTS.DEVCTLHLT bit polling timeout.
Ignore the late xferNotReady event if the controller is already in a
disconnected state.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250807090700.2397190-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eb0337615 upstream.
xHC controller may immediately reuse a slot_id after it's disabled,
giving it to a new enumerating device before the xhci driver freed
all resources related to the disabled device.
In such a scenario, device-A with slot_id equal to 1 is disconnecting
while device-B is enumerating, device-B will fail to enumerate in the
follow sequence.
1.[device-A] send disable slot command
2.[device-B] send enable slot command
3.[device-A] disable slot command completed and wakeup waiting thread
4.[device-B] enable slot command completed with slot_id equal to 1 and
wakeup waiting thread
5.[device-B] driver checks that slot_id is still in use (by device-A) in
xhci_alloc_virt_device, and fail to enumerate due to this
conflict
6.[device-A] xhci->devs[slot_id] set to NULL in xhci_free_virt_device
To fix driver's slot_id resources conflict, clear xhci->devs[slot_id] and
xhci->dcbba->dev_context_ptrs[slot_id] pointers in the interrupt context
when disable slot command completes successfully. Simultaneously, adjust
function xhci_free_virt_device to accurately handle device release.
[minor smatch warning and commit message fix -Mathias]
Cc: stable@vger.kernel.org
Fixes: 7faac1953e ("xhci: avoid race between disable slot command and host runtime suspend")
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a381c6d6f6 upstream.
Presently in `max_contaminant_is_contaminant()` if there's no
contaminant detected previously, CC is open & stopped toggling and no
contaminant is currently present, TCPC.RC would be programmed to do DRP
toggling. However, it didn't actively look for a connection. This would
lead to Type-C not detect *any* new connections. Hence, in the above
situation, re-enable toggling & program TCPC to look for a new
connection.
Also, return early if TCPC was looking for connection as this indicates
TCPC has neither detected a potential connection nor a change in
contaminant state.
In addition, once dry detection is complete (port is dry), restart
toggling.
Fixes: 02b332a063 ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250815-fix-upstream-contaminant-v2-2-6c8d6c3adafb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cabb6c5f4d upstream.
Low power mode is enabled when reading CC resistance as part of
`max_contaminant_read_resistance_kohm()` and left in that state.
However, it's supposed to work with 1uA current source. To read CC
comparator values current source is changed to 80uA. This causes a storm
of CC interrupts as it (falsely) detects a potential contaminant. To
prevent this, disable low power mode current sourcing before reading
comparator values.
Fixes: 02b332a063 ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/stable/20250814-fix-upstream-contaminant-v1-1-801ce8089031%40google.com
Link: https://lore.kernel.org/r/20250815-fix-upstream-contaminant-v2-1-6c8d6c3adafb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98da66a70a upstream.
Since 'bcs->Residue' has the data type '__le32', convert it to the
correct byte order of the CPU using this driver when assigning it to
the local variable 'residue'.
Cc: stable <stable@kernel.org>
Fixes: 50a6cb932d ("USB: usb_storage: add ums-realtek driver")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://lore.kernel.org/r/20250813145247.184717-3-thorsten.blum@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9420f4757 upstream.
Increase the External ROM access timeouts to prevent failures during
programming of External SPI EEPROM chips. The current timeouts are
too short for some SPI EEPROMs used with uPD720201 controllers.
The current timeout for Chip Erase in renesas_rom_erase() is 100 ms ,
the current timeout for Sector Erase issued by the controller before
Page Program in renesas_fw_download_image() is also 100 ms. Neither
timeout is sufficient for e.g. the Macronix MX25L5121E or MX25V5126F.
MX25L5121E reference manual [1] page 35 section "ERASE AND PROGRAMMING
PERFORMANCE" and page 23 section "Table 8. AC CHARACTERISTICS (Temperature
= 0°C to 70°C for Commercial grade, VCC = 2.7V ~ 3.6V)" row "tCE" indicate
that the maximum time required for Chip Erase opcode to complete is 2 s,
and for Sector Erase it is 300 ms .
MX25V5126F reference manual [2] page 47 section "13. ERASE AND PROGRAMMING
PERFORMANCE (2.3V - 3.6V)" and page 42 section "Table 8. AC CHARACTERISTICS
(Temperature = -40°C to 85°C for Industrial grade, VCC = 2.3V - 3.6V)" row
"tCE" indicate that the maximum time required for Chip Erase opcode to
complete is 3.2 s, and for Sector Erase it is 400 ms .
Update the timeouts such, that Chip Erase timeout is set to 5 seconds,
and Sector Erase timeout is set to 500 ms. Such lengthy timeouts ought
to be sufficient for majority of SPI EEPROM chips.
[1] https://www.macronix.com/Lists/Datasheet/Attachments/8634/MX25L5121E,%203V,%20512Kb,%20v1.3.pdf
[2] https://www.macronix.com/Lists/Datasheet/Attachments/8750/MX25V5126F,%202.5V,%20512Kb,%20v1.1.pdf
Fixes: 2478be82de ("usb: renesas-xhci: Add ROM loader for uPD720201")
Cc: stable <stable@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20250802225526.25431-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fe06185e1 upstream.
The USB core will unmap urb->transfer_dma after SETUP stage completes.
Then the USB controller will access unmapped memory when it received
device descriptor. If iommu is equipped, the entire test can't be
completed due to the memory accessing is blocked.
Fix it by calling map_urb_for_dma() again for IN stage. To reduce
redundant map for urb->transfer_buffer, this will also set
URB_NO_TRANSFER_DMA_MAP flag before first map_urb_for_dma() to skip
dma map for urb->transfer_buffer and clear URB_NO_TRANSFER_DMA_MAP
flag before second map_urb_for_dma().
Fixes: 216e0e563d ("usb: core: hcd: use map_urb_for_dma for single step set feature urb")
Cc: stable <stable@kernel.org>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250806083955.3325299-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e664036cf3 upstream.
Another SanDisk 3.2Gen1 Flash Drive also need DELAY_INIT quick,
or it will randomly work incorrectly on Huawei hisi platforms
when doing reboot test.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250801082728.469406-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9528d32873 upstream.
kcov_remote_start_usb_softirq() the begin of urb's completion callback.
HCDs marked HCD_BH will invoke this function from the softirq and
in_serving_softirq() will detect this properly.
Root-HUB (RH) requests will not be delayed to softirq but complete
immediately in IRQ context.
This will confuse kcov because in_serving_softirq() will report true if
the softirq is served after the hardirq and if the softirq got
interrupted by the hardirq in which currently runs.
This was addressed by simply disabling interrupts in
kcov_remote_start_usb_softirq() which avoided the interruption by the RH
while a regular completion callback was invoked.
This not only changes the behaviour while kconv is enabled but also
breaks PREEMPT_RT because now sleeping locks can no longer be acquired.
Revert the previous fix. Address the issue by invoking
kcov_remote_start_usb() only if the context is just "serving softirqs"
which is identified by checking in_serving_softirq() and in_hardirq()
must be false.
Fixes: f85d39dd7e ("kcov, usb: disable interrupts in kcov_remote_start_usb_softirq")
Cc: stable <stable@kernel.org>
Reported-by: Yunseong Kim <ysk@kzalloc.com>
Closes: https://lore.kernel.org/all/20250725201400.1078395-2-ysk@kzalloc.com/
Tested-by: Yunseong Kim <ysk@kzalloc.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250811082745.ycJqBXMs@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e61f6ab08 ]
This patch fixes a race condition communication error, which ends up in
PD hard resets when losing the race. Some systems, like the Radxa ROCK
5B are powered through USB-C without any backup power source and use a
FUSB302 chip to do the PD negotiation. This means it is quite important
to avoid hard resets, since that effectively kills the system's
power-supply.
I've found the following race condition while debugging unplanned power
loss during booting the board every now and then:
1. lots of TCPM/FUSB302/PD initialization stuff
2. TCPM ends up in SNK_WAIT_CAPABILITIES (tcpm_set_pd_rx is enabled here)
3. the remote PD source does not send anything, so TCPM does a SOFT RESET
4. TCPM ends up in SNK_WAIT_CAPABILITIES for the second time
(tcpm_set_pd_rx is enabled again, even though it is still on)
At this point I've seen broken CRC good messages being send by the
FUSB302 with a logic analyzer sniffing the CC lines. Also it looks like
messages are being lost and things generally going haywire with one of
the two sides doing a hard reset once a broken CRC good message was send
to the bus.
I think the system is running into a race condition, that the FIFOs are
being cleared and/or the automatic good CRC message generation flag is
being updated while a message is already arriving.
Let's avoid this by caching the PD RX enabled state, as we have already
processed anything in the FIFOs and are in a good state. As a side
effect that this also optimizes I2C bus usage :)
As far as I can tell the problem theoretically also exists when TCPM
enters SNK_WAIT_CAPABILITIES the first time, but I believe this is less
critical for the following reason:
On devices like the ROCK 5B, which are powered through a TCPM backed
USB-C port, the bootloader must have done some prior PD communication
(initial communication must happen within 5 seconds after plugging the
USB-C plug). This means the first time the kernel TCPM state machine
reaches SNK_WAIT_CAPABILITIES, the remote side is not sending messages
actively. On other devices a hard reset simply adds some extra delay and
things should be good afterwards.
Fixes: c034a43e72 ("staging: typec: Fairchild FUSB302 Type-c chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704-fusb302-race-condition-fix-v1-1-239012c0e27a@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13b3af26a4 ]
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-3-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 1e61f6ab08 ("usb: typec: fusb302: cache PD RX state")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 086a0e516f upstream.
Make sure to drop the reference to the dwc3 device taken by
of_find_device_by_node() on probe errors and on driver unbind.
Fixes: 6dd2565989 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93b400f495 upstream.
Make sure to drop the references taken to the child devices by
of_find_device_by_node() during probe on driver unbind.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Cc: stable@vger.kernel.org # 5.2
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20250724091910.21092-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1473e9e767 upstream.
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 8934d3e4d0 ("usb: musb: omap2430: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 868837b0a9 upstream.
Make sure to drop the reference to the companion device taken during
probe when the driver is unbound.
Fixes: 39facfa01c ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Cc: stable@vger.kernel.org # 4.19
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d1b02e5d7 upstream.
After a recent change in clang to expose uninitialized warnings from
const variables [1], there is a warning in cxacru_heavy_init():
drivers/usb/atm/cxacru.c:1104:6: error: variable 'bp' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
1104 | if (instance->modem_type->boot_rom_patch) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/atm/cxacru.c:1113:39: note: uninitialized use occurs here
1113 | cxacru_upload_firmware(instance, fw, bp);
| ^~
drivers/usb/atm/cxacru.c:1104:2: note: remove the 'if' if its condition is always true
1104 | if (instance->modem_type->boot_rom_patch) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/atm/cxacru.c:1095:32: note: initialize the variable 'bp' to silence this warning
1095 | const struct firmware *fw, *bp;
| ^
| = NULL
While the warning is technically correct that bp is conditionally passed
uninitialized to cxacru_upload_firmware(), it is ultimately a false
positive warning on the uninitialized use of bp because the same
condition that initializes bp, instance->modem_type->boot_rom_patch, is
the same one that gates the use of bp within cxacru_upload_firmware().
As this warning occurs in clang's frontend before inlining occurs, it
cannot know that these conditions are indentical to avoid the warning.
Manually inline cxacru_upload_firmware() into cxacru_heavy_init(), as
that is its only callsite, so that clang can see that bp is initialized
and used under the same condition, clearing up the warning without any
functional changes to the code (LLVM was already doing this inlining
later).
Cc: stable@vger.kernel.org
Fixes: 1b0e614652 ("[PATCH] USB ATM: driver for the Conexant AccessRunner chipset cxacru")
Closes: https://github.com/ClangBuiltLinux/linux/issues/2102
Link: 2464313eef [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250722-usb-cxacru-fix-clang-21-uninit-warning-v2-1-6708a18decd2@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64690a90cd upstream.
On the devices that need their endpoints to get an
initial clear_halt, this needs to be done before
the devices can be opened. That means it needs to be
before the devices are registered.
Fixes: 15bf722e6f ("cdc-acm: Add support of ATOL FPrint fiscal printers")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250717141259.2345605-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7616f006db upstream.
The current power direction of an USB-C port also influences the
power_supply's online status, so a power role change should also update
the power_supply.
Fixes an issue on some systems where plugging in a normal USB device in
for the first time after a reboot will cause upower to erroneously
consider the system to be connected to AC power.
Cc: stable <stable@kernel.org>
Fixes: 0e6371fbfb ("usb: typec: ucsi: Report power supply changes")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250721-fix-ucsi-pwr-dir-notify-v1-1-e53d5340cb38@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf16f40836 upstream.
usb_parse_ss_endpoint_companion() checks descriptor type before length,
enabling a potentially odd read outside of the buffer size.
Fix this up by checking the size first before looking at any of the
fields in the descriptor.
Signed-off-by: Xinyu Liu <katieeliu@tencent.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 503bbde34c ]
Checking for the endpoint type is no reason for a WARN, as that can
cause a reboot. A driver not checking the endpoint type must not cause a
reboot, as there is just no point in this. We cannot prevent a device
from doing something incorrect as a reaction to a transfer. Hence
warning for a mere assumption being wrong is not sensible.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250612122149.2559724-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df9a825f33 ]
If pmc_usb_probe is called before SCU IPC is registered, pmc_usb_probe
will fail.
Return -EPROBE_DEFER when pmc_usb_probe doesn't get SCU IPC device, so
the probe function can be called again after SCU IPC is initialized.
Signed-off-by: Tomasz Michalec <tmichalec@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250610154058.1859812-1-tmichalec@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31611223fb ]
This driver calls enable_irq_wake() during probe() unconditionally, and
never issues the required corresponding disable_irq_wake() to disable
hardware interrupt wakeup signals.
Additionally, whether or not a device should wake-up the system is
meant to be a policy decision based on sysfs (.../power/wakeup) in the
first place.
Update the driver to use the standard approach to enable/disable IRQ
wake during the suspend/resume callbacks. This solves both issues
described above.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250707-max77759-irq-wake-v1-1-d367f633e4bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b9c60e440 ]
When a USB4 dock is unplugged from a system it won't respond to ring
events. The PCI core handles the surprise removal event and notifies
all PCI drivers. The XHCI PCI driver sets a flag that the device is
being removed as well.
When that flag is set don't show messages in the cleanup path for
marking the controller dead.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f72b9aa821 ]
There is a subtle contradiction between sections of the xHCI 1.2 spec
regarding the initialization of Input Endpoint Context fields. Section
4.8.2 ("Endpoint Context Initialization") states that all fields should
be initialized to 0. However, Section 6.2.3 ("Endpoint Context", p.453)
specifies that the Average TRB Length (avg_trb_len) field shall be
greater than 0, and explicitly notes (p.454): "Software shall set
Average TRB Length to '8' for control endpoints."
Strictly setting all fields to 0 during initialization conflicts with
the specific recommendation for control endpoints. In practice, setting
avg_trb_len = 0 is not meaningful for the hardware/firmware, as the
value is used for bandwidth calculation.
Motivation: Our company is developing a custom Virtual xHC hardware
platform that strictly follows the xHCI spec and its recommendations.
During validation, we observed that enumeration fails and a parameter
error (TRB Completion Code = 5) is reported if avg_trb_len for EP0 is
not set to 8 as recommended by Section 6.2.3. This demonstrates the
importance of assigning a meaningful, non-zero value to avg_trb_len,
even in virtualized or emulated environments.
This patch explicitly sets avg_trb_len to 8 for EP0 in
xhci_setup_addressable_virt_dev(), as recommended in Section 6.2.3, to
prevent potential issues with xHCI host controllers that enforce the
spec strictly.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220033
Signed-off-by: Jay Chen <shawn2000100@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65fc0fc137 ]
When a USB4 dock is unplugged from a system it won't respond to ring
events. The PCI core handles the surprise removal event and notifies
all PCI drivers. The XHCI PCI driver sets a flag that the device is
being removed, and when the device stops responding a flag is also
added to indicate it's dying.
When that flag is set don't bother to show warnings about a missing
controller.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250717073107.488599-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af833e7f7d ]
ucsi_psy_get_current_max would return 0mA as the maximum current if
UCSI detected a BC or a Default USB Power sporce.
The comment in this function is true that we can't tell the difference
between DCP/CDP or SDP chargers, but we can guarantee that at least 1-unit
of USB 1.1/2.0 power is available, which is 100mA, which is a better
fallback value than 0, which causes some userspaces, including the ChromeOS
power manager, to regard this as a power source that is not providing
any power.
In reality, 100mA is guaranteed from all sources in these classes.
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Jameson Thies <jthies@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250717200805.3710473-1-bleung@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7919407eca ]
When encounters some errors like these:
xhci_hcd 0000:4a:00.2: xHCI dying or halted, can't queue_command
xhci_hcd 0000:4a:00.2: FIXME: allocate a command ring segment
usb usb5-port6: couldn't allocate usb_device
It's hard to know whether xhc_state is dying or halted. So it's better
to print xhc_state's value which can help locate the resaon of the bug.
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20250725060117.1773770-1-suhui@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 151c0aa896 upstream.
1. In func configfs_composite_bind() -> composite_os_desc_req_prepare():
if kmalloc fails, the pointer cdev->os_desc_req will be freed but not
set to NULL. Then it will return a failure to the upper-level function.
2. in func configfs_composite_bind() -> composite_dev_cleanup():
it will checks whether cdev->os_desc_req is NULL. If it is not NULL, it
will attempt to use it.This will lead to a use-after-free issue.
BUG: KASAN: use-after-free in composite_dev_cleanup+0xf4/0x2c0
Read of size 8 at addr 0000004827837a00 by task init/1
CPU: 10 PID: 1 Comm: init Tainted: G O 5.10.97-oh #1
kasan_report+0x188/0x1cc
__asan_load8+0xb4/0xbc
composite_dev_cleanup+0xf4/0x2c0
configfs_composite_bind+0x210/0x7ac
udc_bind_to_driver+0xb4/0x1ec
usb_gadget_probe_driver+0xec/0x21c
gadget_dev_desc_UDC_store+0x264/0x27c
Fixes: 37a3a53342 ("usb: gadget: OS Feature Descriptors support")
Cc: stable <stable@kernel.org>
Signed-off-by: Tao Xue <xuetao09@huawei.com>
Link: https://lore.kernel.org/r/20250721093908.14967-1-xuetao09@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62783c30d7 upstream.
In hidg_bind(), if alloc_workqueue() fails after usb_assign_descriptors()
has successfully allocated the USB descriptors, the current error handling
does not call usb_free_all_descriptors() to free the allocated descriptors,
resulting in a memory leak.
Restructure the error handling by adding proper cleanup labels:
- fail_free_all: cleans up workqueue and descriptors
- fail_free_descs: cleans up descriptors only
- fail: original cleanup for earlier failures
This ensures that allocated resources are properly freed in reverse order
of their allocation, preventing the memory leak when alloc_workqueue() fails.
Fixes: a139c98f76 ("USB: gadget: f_hid: Add GET_REPORT via userspace IOCTL")
Cc: stable@vger.kernel.org
Signed-off-by: Yuhao Jiang <danisjiang@gmail.com>
Link: https://lore.kernel.org/r/20250623094844.244977-1-danisjiang@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 168c3896f3 ]
Fix memory leak and call ucsi_destroy() from the driver's remove
function and probe's error path in order to remove debugfs files and
free the memory. Also call yoga_c630_ec_unregister_notify() in the
probe's error path.
Fixes: 2ea6d07efe ("usb: typec: ucsi: add Lenovo Yoga C630 glue driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-1-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43007b89fb ]
When multiple Apple devices are connected concurrently, the
apple-mfi-fastcharge driver fails to probe the subsequent devices with
the following error:
sysfs: cannot create duplicate filename '/class/power_supply/apple_mfi_fastcharge'
apple-mfi-fastcharge 5-2.4.3.3: probe of 5-2.4.3.3 failed with error -17
This happens because the driver uses a fixed power supply name
("apple_mfi_fastcharge") for all devices, causing a sysfs name
conflict when a second device is connected.
Fix this by generating unique names using the USB bus and device
number (e.g., "apple_mfi_fastcharge_5-12"). This ensures each
connected device gets a unique power supply entry in sysfs.
The change requires storing a copy of the power_supply_desc structure
in the per-device mfi_device struct, since the name pointer needs to
remain valid for the lifetime of the power supply registration.
Fixes: 249fa8217b ("USB: Add driver to control USB fast charge for iOS devices")
Signed-off-by: Charalampos Mitrodimas <charmitro@posteo.net>
Link: https://lore.kernel.org/r/20250602-apple-mfi-fastcharge-duplicate-sysfs-v1-1-5d84de34fac6@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
