[ Upstream commit 8607edcd17 ]
A recent change to hide USB3 root hubs of USB2-only controllers broke
registration of USB2 root hubs - allow_single_roothub is set too late,
and by this time xhci_run() has already deferred root hub registration
until after the shared HCD is added, which will never happen.
This makes such controllers unusable, but testers didn't notice since
they were only bothered by warnings about empty USB3 root hubs. The bug
causes problems to other people who actually use such HCs and I was
able to confirm it on an ordinary HC by patching to ignore USB3 ports.
Setting allow_single_roothub during early setup fixes things.
Reported-by: Arisa Snowbell <arisa.snowbell@gmail.com>
Closes: https://lore.kernel.org/linux-usb/CABpa4MA9unucCoKtSdzJyOLjHNVy+Cwgz5AnAxPkKw6vuox1Nw@mail.gmail.com/
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Closes: https://lore.kernel.org/linux-usb/lnb5bum7dnzkn3fc7gq6hwigslebo7o4ccflcvsc3lvdgnu7el@fvqpobbdoapl/
Fixes: 719de070f7 ("usb: xhci-pci: add support for hosts with zero USB3 ports")
Tested-by: Arisa Snowbell <arisa.snowbell@gmail.com>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 719de070f7 ]
Add xhci support for PCI hosts that have zero USB3 ports.
Avoid creating a shared Host Controller Driver (HCD) when there is only
one root hub. Additionally, all references to 'xhci->shared_hcd' are now
checked before use.
Only xhci-pci.c requires modification to accommodate this change, as the
xhci core already supports configurations with zero USB3 ports. This
capability was introduced when xHCI Platform and MediaTek added support
for zero USB3 ports.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220181
Tested-by: Nick Nielsen <nick.kainielsen@free.fr>
Tested-by: grm1 <grm1@mailbox.org>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250917210726.97100-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41cf11946b ]
Allow autosuspend to be used by xhci plat device. For Qualcomm SoCs,
when in host mode, it is intended that the controller goes to suspend
state to save power and wait for interrupts from connected peripheral
to wake it up. This is particularly used in cases where a HID or Audio
device is connected. In such scenarios, the usb controller can enter
auto suspend and resume action after getting interrupts from the
connected device.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250916120436.3617598-1-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 368ed48a5e ]
The usbmon binary interface currently truncates captures of large
transfers from higher-speed USB devices. Because a single event capture
is limited to one-fifth of the total buffer size, the current maximum
size of a captured URB is around 240 KiB. This is insufficient when
capturing traffic from modern devices that use transfers of several
hundred kilobytes or more, as truncated URBs can make it impossible for
user-space USB analysis tools like Wireshark to properly defragment and
reassemble higher-level protocol packets in the captured data.
The root cause of this issue is the 1200 KiB BUFF_MAX limit, which has
not been changed since the binary interface was introduced in 2006.
To resolve this issue, this patch increases BUFF_MAX to 64 MiB. The
original comment for BUFF_MAX based the limit's calculation on a
saturated 480 Mbit/s bus. Applying the same logic to a modern USB 3.2
Gen 2×2 20 Gbit/s bus (~2500 MB/s over a 20ms window) indicates the
buffer should be at least 50 MB. The new limit of 64 MiB covers that,
plus a little extra for any overhead.
With this change, both users and developers should now be able to debug
and reverse engineer modern USB devices even when running unmodified
distro kernels.
Please note that this change does not affect the default buffer size. A
larger buffer is only allocated when a user explicitly requests it via
the MON_IOCT_RING_SIZE ioctl, so the change to the maximum buffer size
should not unduly increase memory usage for users that don't
deliberately request a larger buffer.
Link: https://lore.kernel.org/CAO3ALPzdUkmMr0YMrODLeDSLZqNCkWcAP8NumuPHLjNJ8wC1kQ@mail.gmail.com
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/CAO3ALPxU5RzcoueC454L=WZ1qGMfAcnxm+T+p+9D8O9mcrUbCQ@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c5ff5615 ]
In the __cdnsp_gadget_init() and cdnsp_gadget_exit() functions, the gadget
structure (pdev->gadget) was freed before its endpoints.
The endpoints are linked via the ep_list in the gadget structure.
Freeing the gadget first leaves dangling pointers in the endpoint list.
When the endpoints are subsequently freed, this results in a use-after-free.
Fix:
By separating the usb_del_gadget_udc() operation into distinct "del" and
"put" steps, cdnsp_gadget_free_endpoints() can be executed prior to the
final release of the gadget structure with usb_put_gadget().
A patch similar to bb9c74a5bd14("usb: dwc3: gadget: Free gadget structure
only after freeing endpoints").
Signed-off-by: Chen Yufeng <chenyufeng@iie.ac.cn>
Link: https://lore.kernel.org/r/20250905094842.1232-1-chenyufeng@iie.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed6f727c57 ]
Set the hid req->zero flag of ep0/in_ep to true by default,
then the UDC drivers can transfer a zero length packet at
the end if the hid transfer with size divisible to EPs max
packet size according to the USB 2.0 spec.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/1756204087-26111-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 956606bafb ]
This fix is already present in f_ecm.c and was never
propagated to f_ncm.c
When creating multiple NCM ethernet devices
on a composite usb gadget device
each MAC address on the HOST side will be identical.
Having the same MAC on different network interfaces is bad.
This fix updates the MAC address inside the
ncm_strings_defs global during the ncm_bind call.
This ensures each device has a unique MAC.
In f_ecm.c ecm_string_defs is updated in the same way.
The defunct MAC assignment in ncm_alloc has been removed.
Signed-off-by: raub camaioni <raubcameo@gmail.com>
Link: https://lore.kernel.org/r/20250815131358.1047525-1-raubcameo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cfd6f1a7b4 upstream.
A race condition occurs when ffs_func_eps_enable() runs concurrently
with ffs_data_reset(). The ffs_data_clear() called in ffs_data_reset()
sets ffs->epfiles to NULL before resetting ffs->eps_count to 0, leading
to a NULL pointer dereference when accessing epfile->ep in
ffs_func_eps_enable() after successful usb_ep_enable().
The ffs->epfiles pointer is set to NULL in both ffs_data_clear() and
ffs_data_close() functions, and its modification is protected by the
spinlock ffs->eps_lock. And the whole ffs_func_eps_enable() function
is also protected by ffs->eps_lock.
Thus, add NULL pointer handling for ffs->epfiles in the
ffs_func_eps_enable() function to fix issues
Signed-off-by: Owen Gu <guhuinan@xiaomi.com>
Link: https://lore.kernel.org/r/20250915092907.17802-1-guhuinan@xiaomi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d8713f807 upstream.
When there is no port entry in the tcpci entry itself, the driver will
trigger an error message "OF: graph: no port node found in /...../typec" .
It is documented that the dts node should contain an connector entry
with ports and several port pointing to devices with usb-role-switch
property set. Only when those connector entry is missing, it should
check for port entries in the main node.
We switch the search order for looking after ports, which will avoid the
failure message while there are explicit connector entries.
Fixes: d56de8c9a1 ("usb: typec: tcpm: try to get role switch from tcpc fwnode")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://patch.msgid.link/20251013-b4-ml-topic-tcpm-v2-1-63c9b2ab8a0b@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3d12ec847 upstream.
DbC may add 1024 bogus bytes to the beginneing of the receiving endpoint
if DbC hw triggers a STALL event before any Transfer Blocks (TRBs) for
incoming data are queued, but driver handles the event after it queued
the TRBs.
This is possible as xHCI DbC hardware may trigger spurious STALL transfer
events even if endpoint is empty. The STALL event contains a pointer
to the stalled TRB, and "remaining" untransferred data length.
As there are no TRBs queued yet the STALL event will just point to first
TRB position of the empty ring, with '0' bytes remaining untransferred.
DbC driver is polling for events, and may not handle the STALL event
before /dev/ttyDBC0 is opened and incoming data TRBs are queued.
The DbC event handler will now assume the first queued TRB (length 1024)
has stalled with '0' bytes remaining untransferred, and copies the data
This race situation can be practically mitigated by making sure the event
handler handles all pending transfer events when DbC reaches configured
state, and only then create dev/ttyDbC0, and start queueing transfers.
The event handler can this way detect the STALL events on empty rings
and discard them before any transfers are queued.
This does in practice solve the issue, but still leaves a small possible
gap for the race to trigger.
We still need a way to distinguish spurious STALLs on empty rings with '0'
bytes remaing, from actual STALL events with all bytes transmitted.
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bbd38fcd2 upstream.
DbC is currently only enabled back if it's in configured state during
suspend.
If system is suspended after DbC is enabled, but before the device is
properly enumerated by the host, then DbC would not be enabled back in
resume.
Always enable DbC back in resume if it's suspended in enabled,
connected, or configured state
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37b9dd0d11 upstream.
Drop the check on the maximum transfer length in Raw Gadget for both
control and non-control transfers.
Limiting the transfer length causes a problem with emulating USB devices
whose full configuration descriptor exceeds PAGE_SIZE in length.
Overall, there does not appear to be any reason to enforce any kind of
transfer length limit on the Raw Gadget side for either control or
non-control transfers, so let's just drop the related check.
Cc: stable <stable@kernel.org>
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://patch.msgid.link/a6024e8eab679043e9b8a5defdb41c4bda62f02b.1761085528.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfc2cf4dca upstream.
The list of Huawei LTE modules needing the quirk fixing spurious wakeups
was missing the IDs of the Huawei ME906S module, therefore suspend did not
work.
Cc: stable <stable@kernel.org>
Signed-off-by: Tim Guttzeit <t.guttzeit@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://patch.msgid.link/20251020134304.35079-1-wse@tuxedocomputers.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0822894143 ]
After an bind/unbind cycle, the rndis->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Fixes: 45fe3b8e53 ("usb ethernet gadget: split RNDIS function")
Cc: stable@kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-6-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-6-4997bf277548@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42988380ac ]
After an bind/unbind cycle, the ecm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Fixes: da741b8c56 ("usb ethernet gadget: split CDC Ethernet function")
Cc: stable@kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-5-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-5-4997bf277548@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47b2116e54 ]
After an bind/unbind cycle, the acm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Call trace:
usb_ep_free_request+0x2c/0xec
gs_free_req+0x30/0x44
acm_bind+0x1b8/0x1f4
usb_add_function+0xcc/0x1f0
configfs_composite_bind+0x468/0x588
gadget_bind_driver+0x104/0x270
really_probe+0x190/0x374
__driver_probe_device+0xa0/0x12c
driver_probe_device+0x3c/0x218
__device_attach_driver+0x14c/0x188
bus_for_each_drv+0x10c/0x168
__device_attach+0xfc/0x198
device_initial_probe+0x14/0x24
bus_probe_device+0x94/0x11c
device_add+0x268/0x48c
usb_add_gadget+0x198/0x28c
dwc3_gadget_init+0x700/0x858
__dwc3_set_mode+0x3cc/0x664
process_scheduled_works+0x1d8/0x488
worker_thread+0x244/0x334
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20
Fixes: 1f1ba11b64 ("usb gadget: issue notifications from ACM function")
Cc: stable@kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-4-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-4-4997bf277548@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75a5b8d4dd ]
After an bind/unbind cycle, the ncm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Call trace:
usb_ep_free_request+0x2c/0xec
ncm_bind+0x39c/0x3dc
usb_add_function+0xcc/0x1f0
configfs_composite_bind+0x468/0x588
gadget_bind_driver+0x104/0x270
really_probe+0x190/0x374
__driver_probe_device+0xa0/0x12c
driver_probe_device+0x3c/0x218
__device_attach_driver+0x14c/0x188
bus_for_each_drv+0x10c/0x168
__device_attach+0xfc/0x198
device_initial_probe+0x14/0x24
bus_probe_device+0x94/0x11c
device_add+0x268/0x48c
usb_add_gadget+0x198/0x28c
dwc3_gadget_init+0x700/0x858
__dwc3_set_mode+0x3cc/0x664
process_scheduled_works+0x1d8/0x488
worker_thread+0x244/0x334
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Cc: stable@kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-3-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-3-4997bf277548@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfb1d99d96 ]
Gadget function drivers often have goto-based error handling in their
bind paths, which can be bug-prone. Refactoring these paths to use
__free() scope-based cleanup is desirable, but currently blocked.
The blocker is that usb_ep_free_request(ep, req) requires two
parameters, while the __free() mechanism can only pass a pointer to the
request itself.
Store an endpoint pointer in the struct usb_request. The pointer is
populated centrally in usb_ep_alloc_request() on every successful
allocation, making the request object self-contained.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-1-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-1-4997bf277548@google.com
Stable-dep-of: 75a5b8d4dd ("usb: gadget: f_ncm: Refactor bind path to use __free()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9c206324e upstream.
The cdnsp-pci driver uses pcim_enable_device() to enable a PCI device,
which means the device will be automatically disabled on driver detach
through the managed device framework. The manual pci_disable_device()
call in the error path is therefore redundant.
Found via static anlaysis and this is similar to commit 99ca0b57e4
("thermal: intel: int340x: processor: Fix warning during module unload").
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20250903141613.2535472-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be5ae730ff upstream.
Right now the interrupt handler first reads all updated status registers
and only then clears the interrupts. It's possible that a duplicate
interrupt for a changed register or plug state comes in after the
interrupts have been processed but before they have been cleared:
* plug is inserted, TPS_REG_INT_PLUG_EVENT is set
* TPS_REG_INT_EVENT1 is read
* tps6598x_handle_plug_event() has run and registered the plug
* plug is removed again, TPS_REG_INT_PLUG_EVENT is set (again)
* TPS_REG_INT_CLEAR1 is written, TPS_REG_INT_PLUG_EVENT is cleared
We then have no plug connected and no pending interrupt but the tipd
core still thinks there is a plug. It's possible to trigger this with
e.g. a slightly broken Type-C to USB A converter.
Fix this by first clearing the interrupts and only then reading the
updated registers.
Fixes: 45188f27b3 ("usb: typec: tipd: Add support for Apple CD321X")
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Cc: stable@kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://lore.kernel.org/r/20250914-apple-usb3-tipd-v1-1-4e99c8649024@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e40b984b6c ]
The VHCI platform driver aims to forbid entering system suspend when at
least one of the virtual USB ports are bound to an active USB/IP
connection.
However, in some cases, the detection logic doesn't work reliably, i.e.
when all devices attached to the virtual root hub have been already
suspended, leading to a broken suspend state, with unrecoverable resume.
Ensure the virtually attached devices do not enter suspend by setting
the syscore PM flag. Note this is currently limited to the client side
only, since the server side doesn't implement system suspend prevention.
Fixes: 04679b3489 ("Staging: USB/IP: add client driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250902-vhci-hcd-suspend-fix-v3-1-864e4e833559@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08fa726e66 ]
This reverts commit 28a76fcc4c.
No actual HW bugs are known where Endpoint Context shows Running state
but Stop Endpoint fails repeatedly with Context State Error and leaves
the endpoint state unchanged. Stop Endpoint retries on Running EPs have
been performed since early 2021 with no such issues reported so far.
Trying to handle this hypothetical case brings a more realistic danger:
if Stop Endpoint fails on an endpoint which hasn't yet started after a
doorbell ring and enough latency occurs before this completion event is
handled, the driver may time out and begin removing cancelled TDs from
a running endpoint, even though one more retry would stop it reliably.
Such high latency is rare but not impossible, and removing TDs from a
running endpoint can cause more damage than not giving back a cancelled
URB (which wasn't happening anyway). So err on the side of caution and
revert to the old policy of always retrying if the EP appears running.
[Remove stable tag as we are dealing with theoretical cases -Mathias]
Fixes: 28a76fcc4c ("usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running")
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250917210726.97100-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e271cc0d25 ]
Once the use_os_string flag is set to true for some functions
(e.g. adb/mtp) which need to response the OS string, and then
if we re-bind the ConfigFS gadget to use the other functions
(e.g. hid) which should not to response the OS string, however,
because the use_os_string flag is still true, so the usb gadget
response the OS string descriptor incorrectly, this can cause
the USB device to be unrecognizable on the Windows system.
An example of this as follows:
echo 1 > os_desc/use
ln -s functions/ffs.adb configs/b.1/function0
start adbd
echo "<udc device>" > UDC #succeed
stop adbd
rm configs/b.1/function0
echo 0 > os_desc/use
ln -s functions/hid.gs0 configs/b.1/function0
echo "<udc device>" > UDC #fail to connect on Windows
This patch sets the use_os_string flag to false at bind if
the functions not support OS Descriptors.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Fixes: 87213d388e ("usb: gadget: configfs: OS String support")
Link: https://lore.kernel.org/r/1755833769-25434-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b570b346dd ]
In the twl6030_usb_probe(), the variable ret is declared as
a u32 type. However, since ret may receive -ENODEV when accepting
the return value of omap_usb2_set_comparator().Therefore, its type
should be changed to int.
Fixes: 0e98de67ba ("usb: otg: make twl6030_usb as a comparator driver to omap_usb2")
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Link: https://lore.kernel.org/r/20250822092224.30645-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0485e864a ]
EUD_MODE_MANAGER2 register is mapped to a memory region that is marked
as read-only for operating system running at EL1, enforcing access
restrictions that prohibit direct memory-mapped writes via writel().
Attempts to write to this region from HLOS can result in silent failures
or memory access violations, particularly when toggling EUD (Embedded
USB Debugger) state. To ensure secure register access, modify the driver
to use qcom_scm_io_writel(), which routes the write operation to Qualcomm
Secure Channel Monitor (SCM). SCM has the necessary permissions to access
protected memory regions, enabling reliable control over EUD state.
SC7280, the only user of EUD is also affected, indicating that this could
never have worked on a properly fused device.
Fixes: 9a1bf58ccd ("usb: misc: eud: Add driver support for Embedded USB Debugger(EUD)")
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Signed-off-by: Komal Bajaj <komal.bajaj@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250731-eud_mode_manager_secure_access-v8-1-4a5dcbb79f41@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 186e8f2bdb ]
The kthread_run() function returns error pointers so the
max3421_hcd->spi_thread pointer can be either error pointers or NULL.
Check for both before dereferencing it.
Fixes: 05dfa5c9bc ("usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/aJTMVAPtRe5H6jug@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Revert commit 9b28ef1e4c which is upstream
commit e1b0fa8639
It causes regression in 6.12.49 stable, no issues in upstream.
Commit 9b28ef1e4c ("usb: xhci: remove option to change a default
ring's TRB cycle bit") introduced a regression in 6.12.49 stable kernel.
The original commit was never intended for stable kernels, but was added
as a dependency for commit a5c98e8b13 ("xhci: dbc: Fix full DbC
transfer ring after several reconnects").
Since this commit is more of an optimization, revert it and solve the
dependecy by modifying one line in xhci_dbc_ring_init(). Specifically,
commit a5c98e8b13 ("xhci: dbc: Fix full DbC transfer ring after
several reconnects") moved function call xhci_initialize_ring_info()
into a separate function. To resolve the dependency, the arguments for
this function call are also reverted.
Closes: https://lore.kernel.org/stable/01b8c8de46251cfaad1329a46b7e3738@stwm.de/
Tested-by: Wolfgang Walter <linux@stwm.de>
Cc: stable@vger.kernel.org # v6.12.49
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47c428fce0 ]
Use "0x%x" format for quirks debug print to clarify it's a hexadecimal
value. Improves readability and consistency with other hex outputs.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Link: https://lore.kernel.org/r/20250603071045.3243699-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5c98e8b13 ]
Pending requests will be flushed on disconnect, and the corresponding
TRBs will be turned into No-op TRBs, which are ignored by the xHC
controller once it starts processing the ring.
If the USB debug cable repeatedly disconnects before ring is started
then the ring will eventually be filled with No-op TRBs.
No new transfers can be queued when the ring is full, and driver will
print the following error message:
"xhci_hcd 0000:00:14.0: failed to queue trbs"
This is a normal case for 'in' transfers where TRBs are always enqueued
in advance, ready to take on incoming data. If no data arrives, and
device is disconnected, then ring dequeue will remain at beginning of
the ring while enqueue points to first free TRB after last cancelled
No-op TRB.
s
Solve this by reinitializing the rings when the debug cable disconnects
and DbC is leaving the configured state.
Clear the whole ring buffer and set enqueue and dequeue to the beginning
of ring, and set cycle bit to its initial state.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 220a0ffde0 ]
Decouple allocation of endpoint ring buffer from initialization
of the buffer, and initialization of endpoint context parts from
from the rest of the contexts.
It allows driver to clear up and reinitialize endpoint rings
after disconnect without reallocating everything.
This is a prerequisite for the next patch that prevents the transfer
ring from filling up with cancelled (no-op) TRBs if a debug cable is
reconnected several times without transferring anything.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a5c98e8b13 ("xhci: dbc: Fix full DbC transfer ring after several reconnects")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1b0fa8639 ]
The TRB cycle bit indicates TRB ownership by the Host Controller (HC) or
Host Controller Driver (HCD). New rings are initialized with 'cycle_state'
equal to one, and all its TRBs' cycle bits are set to zero. When handling
ring expansion, set the source ring cycle bits to the same value as the
destination ring.
Move the cycle bit setting from xhci_segment_alloc() to xhci_link_rings(),
and remove the 'cycle_state' argument from xhci_initialize_ring_info().
The xhci_segment_alloc() function uses kzalloc_node() to allocate segments,
ensuring that all TRB cycle bits are initialized to zero.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a5c98e8b13 ("xhci: dbc: Fix full DbC transfer ring after several reconnects")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f970bd06c ]
Add macro to streamline and standardize the iteration over ring
segment list.
xhci_for_each_ring_seg(): Iterates over the entire ring segment list.
The xhci_free_segments_for_ring() function's while loop has not been
updated to use the new macro. This function has some underlying issues,
and as a result, it will be handled separately in a future patch.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a5c98e8b13 ("xhci: dbc: Fix full DbC transfer ring after several reconnects")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 116e79c679 upstream.
The EP-IN of MIDI2 (altset 1) wasn't initialized in
f_midi2_create_usb_configs() as it's an INT EP unlike others BULK
EPs. But this leaves rather the max packet size unchanged no matter
which speed is used, resulting in the very slow access.
And the wMaxPacketSize values set there look legit for INT EPs, so
let's initialize the MIDI2 EP-IN there for achieving the equivalent
speed as well.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250905133240.20966-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21d8525d2e upstream.
The gadget card driver forgot to call snd_ump_update_group_attrs()
after adding FBs, and this leaves the UMP group attributes
uninitialized. As a result, -ENODEV error is returned at opening a
legacy rawmidi device as an inactive group.
This patch adds the missing call to address the behavior above.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250904153932.13589-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f34bfcc77b upstream.
tcpm_handle_vdm_request delivers messages to the partner altmode or the
cable altmode depending on the SVDM response type, which is incorrect.
The partner or cable should be chosen based on the received message type
instead.
Also add this filter to ADEV_NOTIFY_USB_AND_QUEUE_VDM, which is used when
the Enter Mode command is responded to by a NAK on SOP or SOP' and when
the Exit Mode command is responded to by an ACK on SOP.
Fixes: 7e7877c55e ("usb: typec: tcpm: add alt mode enter/exit/vdm support for sop'")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250821203759.1720841-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d63c83d8e upstream.
Yunseong Kim and the syzbot fuzzer both reported a problem in
RT-enabled kernels caused by the way dummy-hcd mixes interrupt
management and spin-locking. The pattern was:
local_irq_save(flags);
spin_lock(&dum->lock);
...
spin_unlock(&dum->lock);
... // calls usb_gadget_giveback_request()
local_irq_restore(flags);
The code was written this way because usb_gadget_giveback_request()
needs to be called with interrupts disabled and the private lock not
held.
While this pattern works fine in non-RT kernels, it's not good when RT
is enabled. RT kernels handle spinlocks much like mutexes; in particular,
spin_lock() may sleep. But sleeping is not allowed while local
interrupts are disabled.
To fix the problem, rewrite the code to conform to the pattern used
elsewhere in dummy-hcd and other UDC drivers:
spin_lock_irqsave(&dum->lock, flags);
...
spin_unlock(&dum->lock);
usb_gadget_giveback_request(...);
spin_lock(&dum->lock);
...
spin_unlock_irqrestore(&dum->lock, flags);
This approach satisfies the RT requirements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Fixes: b4dbda1a22 ("USB: dummy-hcd: disable interrupts during req->complete")
Reported-by: Yunseong Kim <ysk@kzalloc.com>
Closes: <https://lore.kernel.org/linux-usb/5b337389-73b9-4ee4-a83e-7e82bf5af87a@kzalloc.com/>
Reported-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
Closes: <https://lore.kernel.org/linux-usb/68ac2411.050a0220.37038e.0087.GAE@google.com/>
Tested-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
CC: stable@vger.kernel.org
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/bb192ae2-4eee-48ee-981f-3efdbbd0d8f0@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edcbe06453 upstream.
Suspend-resume cycle test revealed a memory leak in 6.17-rc3
Turns out the slot_id race fix changes accidentally ends up calling
xhci_free_virt_device() with an incorrect vdev parameter.
The vdev variable was reused for temporary purposes right before calling
xhci_free_virt_device().
Fix this by passing the correct vdev parameter.
The slot_id race fix that caused this regression was targeted for stable,
so this needs to be applied there as well.
Fixes: 2eb0337615 ("usb: xhci: Fix slot_id resource race conflict")
Reported-by: David Wang <00107082@163.com>
Closes: https://lore.kernel.org/linux-usb/20250829181354.4450-1-00107082@163.com
Suggested-by: Michal Pecio <michal.pecio@gmail.com>
Suggested-by: David Wang <00107082@163.com>
Cc: stable@vger.kernel.org
Tested-by: David Wang <00107082@163.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45eae113dc upstream.
This commit addresses a rarely observed endpoint command timeout
which causes kernel panic due to warn when 'panic_on_warn' is enabled
and unnecessary call trace prints when 'panic_on_warn' is disabled.
It is seen during fast software-controlled connect/disconnect testcases.
The following is one such endpoint command timeout that we observed:
1. Connect
=======
->dwc3_thread_interrupt
->dwc3_ep0_interrupt
->configfs_composite_setup
->composite_setup
->usb_ep_queue
->dwc3_gadget_ep0_queue
->__dwc3_gadget_ep0_queue
->__dwc3_ep0_do_control_data
->dwc3_send_gadget_ep_cmd
2. Disconnect
==========
->dwc3_thread_interrupt
->dwc3_gadget_disconnect_interrupt
->dwc3_ep0_reset_state
->dwc3_ep0_end_control_data
->dwc3_send_gadget_ep_cmd
In the issue scenario, in Exynos platforms, we observed that control
transfers for the previous connect have not yet been completed and end
transfer command sent as a part of the disconnect sequence and
processing of USB_ENDPOINT_HALT feature request from the host timeout.
This maybe an expected scenario since the controller is processing EP
commands sent as a part of the previous connect. It maybe better to
remove WARN_ON in all places where device endpoint commands are sent to
avoid unnecessary kernel panic due to warn.
Cc: stable <stable@kernel.org>
Co-developed-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250808125315.1607-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58577118cc upstream.
During a device-initiated disconnect, the End Transfer command resets
the event filter, allowing a new xferNotReady event to be generated
before the controller is fully halted. Processing this late event
incorrectly triggers a Start Transfer, which prevents the controller
from halting and results in a DSTS.DEVCTLHLT bit polling timeout.
Ignore the late xferNotReady event if the controller is already in a
disconnected state.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250807090700.2397190-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eb0337615 upstream.
xHC controller may immediately reuse a slot_id after it's disabled,
giving it to a new enumerating device before the xhci driver freed
all resources related to the disabled device.
In such a scenario, device-A with slot_id equal to 1 is disconnecting
while device-B is enumerating, device-B will fail to enumerate in the
follow sequence.
1.[device-A] send disable slot command
2.[device-B] send enable slot command
3.[device-A] disable slot command completed and wakeup waiting thread
4.[device-B] enable slot command completed with slot_id equal to 1 and
wakeup waiting thread
5.[device-B] driver checks that slot_id is still in use (by device-A) in
xhci_alloc_virt_device, and fail to enumerate due to this
conflict
6.[device-A] xhci->devs[slot_id] set to NULL in xhci_free_virt_device
To fix driver's slot_id resources conflict, clear xhci->devs[slot_id] and
xhci->dcbba->dev_context_ptrs[slot_id] pointers in the interrupt context
when disable slot command completes successfully. Simultaneously, adjust
function xhci_free_virt_device to accurately handle device release.
[minor smatch warning and commit message fix -Mathias]
Cc: stable@vger.kernel.org
Fixes: 7faac1953e ("xhci: avoid race between disable slot command and host runtime suspend")
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a381c6d6f6 upstream.
Presently in `max_contaminant_is_contaminant()` if there's no
contaminant detected previously, CC is open & stopped toggling and no
contaminant is currently present, TCPC.RC would be programmed to do DRP
toggling. However, it didn't actively look for a connection. This would
lead to Type-C not detect *any* new connections. Hence, in the above
situation, re-enable toggling & program TCPC to look for a new
connection.
Also, return early if TCPC was looking for connection as this indicates
TCPC has neither detected a potential connection nor a change in
contaminant state.
In addition, once dry detection is complete (port is dry), restart
toggling.
Fixes: 02b332a063 ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250815-fix-upstream-contaminant-v2-2-6c8d6c3adafb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cabb6c5f4d upstream.
Low power mode is enabled when reading CC resistance as part of
`max_contaminant_read_resistance_kohm()` and left in that state.
However, it's supposed to work with 1uA current source. To read CC
comparator values current source is changed to 80uA. This causes a storm
of CC interrupts as it (falsely) detects a potential contaminant. To
prevent this, disable low power mode current sourcing before reading
comparator values.
Fixes: 02b332a063 ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/stable/20250814-fix-upstream-contaminant-v1-1-801ce8089031%40google.com
Link: https://lore.kernel.org/r/20250815-fix-upstream-contaminant-v2-1-6c8d6c3adafb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
