[ Upstream commit 4c4ed5e073 ]
According to I2S specs audio data is sampled on the rising edge of the
clock and it can change on the falling one. When operating in normal mode
this SoC behaves the opposite so a clock polarity inversion is required
in this case.
This was tested on an OdroidC2 (Amlogic S905 SoC) board.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patch.msgid.link/20251007-fix-i2s-polarity-v1-1-86704d9cda10@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 659169c4eb ]
The 1824c does not have the A/B switch that the 1810c has,
but instead it has a mono main switch that sums the two
main output channels to mono.
Signed-off-by: Roy Vegard Ovesen <roy.vegard.ovesen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 733a763dd8 ]
The problem of having class-D initialization sequence in probe using
regmap_register_patch() is that it will do hardware register writes
immediately after being called as it bypasses regcache. Afterwards, in
aic3x_init() we also perform codec soft reset, rendering class-D init
sequence pointless. This issue is even more apparent when using reset
GPIO line, since in that case class-D amplifier initialization fails
with "Failed to init class D: -5" message as codec is already held in
reset state after requesting the reset GPIO and hence hardware I/O
fails with -EIO errno.
Thus move class-D amplifier initialization sequence from probe function
to aic3x_set_power() just before the usual regcache sync. Use bypassed
regmap_multi_reg_write_bypassed() function to make sure, class-D init
sequence is performed in proper order as described in the datasheet.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Link: https://patch.msgid.link/20250925085929.2581749-1-primoz.fiser@norik.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27fa1a8b28 ]
The mclk direction now needs to be specified in endpoint node with
"system-clock-direction-out" property. However some calls to the
set_sysclk callback, related to CPU DAI clock, result in unbalanced
calls to clock API.
The set_sysclk callback in STM32 SAI driver is intended only for mclk
management. So it is relevant to ensure that calls to set_sysclk are
related to mclk only.
Since the master clock is handled only at runtime, skip the calls to
set_sysclk in the initialization phase.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://patch.msgid.link/20250916123118.84175-1-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9565c9d53c ]
Setting format to s16le is required for compressed playback on compatible
soundcards.
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20250911154340.2798304-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8497324901 ]
If multiple instances of this driver are instantiated and try to send
concurrently then the single static buffer snd_serial_generic_tx_work()
will cause corruption in the data output.
Move the buffer into the per-instance driver data to avoid this.
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a73349c5dd ]
It reports a MIN value -15360 for volume control, but will mute when
setting it less than -14208
Tested-by: Guoli An <anguoli@uniontech.com>
Signed-off-by: Cryolitia PukNgae <cryolitia@uniontech.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250903-sound-v1-4-d4ca777b8512@uniontech.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ad299a9b9 ]
We can have modules in path which can change the number of channels and in
this case the BE params needs to be adjusted to configure the DAI according
to the copier configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Message-ID: <20250829105305.31818-2-peter.ujfalusi@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2aec0b6a6b ]
Just add fixed struct size validations for UAC2 and UAC3 effect
units. The descriptor has a variable-length array, so it should be
validated with a proper function later once when the unit is really
parsed and used by the driver (currently only referred partially for
the input terminal parsing).
Link: https://patch.msgid.link/20250821151751.12100-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ed2dca4df ]
The SND_JACK_AVOUT is a more specific jack type for HDMI and DisplayPort.
Updatae the MediaTek drivers to use such jack type, allowing system to
determine the device type based on jack event.
Signed-off-by: Terry Cheong <htcheong@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20250723-mtk-hdmi-v1-1-4ff945eb6136@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2dd1d0d32 ]
When configured for default synchronisation (Rx syncs to Tx) and the
SAI operates in consumer mode (clocks provided externally to Tx), a
synchronisation error occurs on Tx on the first attempt after device
initialisation when the playback stream is started while a capture
stream is already active. This results in channel shift/swap on the
playback stream.
Subsequent streams (ie after that first failing one) always work
correctly, no matter the order, with or without the other stream active.
This issue was observed (and fix tested) on an i.MX6UL board connected
to an ADAU1761 codec, where the codec provides both frame and bit clock
(connected to TX pins).
To fix this, always initialize the 'other' xCR4 and xCR5 registers when
we're starting a stream which is synced to the opposite one, irregardless
of the producer/consumer status.
Fixes: 51659ca069 ("ASoC: fsl-sai: set xCR4/xCR5/xMR for SAI master mode")
Signed-off-by: Maarten Zanders <maarten@zanders.be>
Reviewed-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://patch.msgid.link/20251024135716.584265-1-maarten@zanders.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9fbe5b0bf ]
The DSD little endian format requires the msb first, because oldest bit
is in msb.
found this issue by testing with pipewire.
Fixes: c111c2ddb3 ("ASoC: fsl_sai: Add PDM daifmt support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/20251023064538.368850-2-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 845f716dc5 ]
avs_dai_fe_shutdown() handles the shutdown procedure for HOST HDAudio
stream while period-elapsed work services its IRQs. As the former
frees the DAI's private context, these two operations shall be
synchronized to avoid slab-use-after-free or worse errors.
Fixes: 0dbb186c35 ("ASoC: Intel: avs: Update stream status in a separate thread")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20251023092348.3119313-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfca1637bc ]
The pcm->prepare() function may be called multiple times in a row by the
userspace, as mentioned in the documentation. The driver shall take that
into account and prevent redundancy. However, the exact same function is
called during XRUNs and in such case, the particular stream shall be
reset and setup anew.
Fixes: 9114700b49 ("ASoC: Intel: avs: Generic PCM FE operations")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20251023092348.3119313-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec20584f25 ]
cs-amp-lib-test uses functions from kunit/test-bug.h but wasn't
including it.
This error was found by smatch.
Fixes: 177862317a ("ASoC: cs-amp-lib: Add KUnit test for calibration helpers")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20251016094844.92796-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7963891f7c ]
Since the requesttype has USB_DIR_OUT the pipe should be
constructed with usb_sndctrlpipe().
Fixes: 8dc5efe3d1 ("ALSA: usb-audio: Add support for Presonus Studio 1810c")
Signed-off-by: Roy Vegard Ovesen <roy.vegard.ovesen@gmail.com>
Link: https://patch.msgid.link/aPPL3tBFE_oU-JHv@ark
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fdbb53d318 upstream.
For some reason we ended up kfree between spinlock lock and unlock,
which can sleep.
move the kfree out of spinlock section.
Fixes: a2a5d30218 ("ASoC: qdsp6: q6asm: Add support to memory map and unmap")
Cc: Stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251017085307.4325-2-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5726b68473 ]
devm_kasprintf() may return NULL on memory allocation failure,
but the debug message prints cpus->dai_name before checking it.
Move the dev_dbg() call after the NULL check to prevent potential
NULL pointer dereference.
Fixes: cb8ea62e64 ("ASoC: amd/sdw_utils: add sof based soundwire generic machine driver")
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Link: https://patch.msgid.link/20251015075530.146851-1-liqiang01@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28412b489b ]
In try_to_register_card(), the return value of usb_ifnum_to_if() is
passed directly to usb_interface_claimed() without a NULL check, which
will lead to a NULL pointer dereference when creating an invalid
USB audio device. Fix this by adding a check to ensure the interface
pointer is valid before passing it to usb_interface_claimed().
Fixes: 39efc9c8a9 ("ALSA: usb-audio: Fix last interface check for registration")
Closes: https://lore.kernel.org/all/CANypQFYtQxHL5ghREs-BujZG413RPJGnO5TH=xjFBKpPts33tA@mail.gmail.com/
Signed-off-by: Jiaming Zhang <r772577952@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b4eda7bf7 ]
Stress testing the audio jack hotplug handling on a few Steam Deck units
revealed that the debounce circuit is responsible for having a negative
impact on the detection reliability, e.g. in some cases the ejection
interrupt is not fired, while in other instances it goes into a kind of
invalid state and generates a flood of misleading interrupts.
Add new entries to the DMI table introduced via commit 1bc40efdaf
("ASoC: nau8821: Add DMI quirk mechanism for active-high jack-detect")
and extend the quirk logic to allow bypassing the debounce circuit used
for jack detection on Valve Steam Deck LCD and OLED models.
While at it, rename existing NAU8821_JD_ACTIVE_HIGH quirk bitfield to
NAU8821_QUIRK_JD_ACTIVE_HIGH. This should help improve code readability
by differentiating from similarly named register bits.
Fixes: aab1ad11d6 ("ASoC: nau8821: new driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251003-nau8821-jdet-fixes-v1-4-f7b0e2543f09@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9273aa85b3 ]
Instead of adding yet another utility function for dealing with the
interrupt clearing register, generalize nau8821_int_status_clear_all()
by renaming it to nau8821_irq_status_clear(), whilst introducing a
second parameter to allow restricting the operation scope to a single
interrupt instead of the whole range of active IRQs.
While at it, also fix a spelling typo in the comment block.
Note this is mainly a prerequisite for subsequent patches aiming to
address some deficiencies in the implementation of the interrupt
handler. Thus the presence of the Fixes tag below is intentional, to
facilitate backporting.
Fixes: aab1ad11d6 ("ASoC: nau8821: new driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251003-nau8821-jdet-fixes-v1-2-f7b0e2543f09@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e54919cb5 ]
The microphone detection work scheduled by a prior jack insertion
interrupt may still be in a pending state or under execution when a jack
ejection interrupt has been fired.
This might lead to a racing condition or nau8821_jdet_work() completing
after nau8821_eject_jack(), which will override the currently
disconnected state of the jack and incorrectly report the headphone or
the headset as being connected.
Cancel any pending jdet_work or wait for its execution to finish before
attempting to handle the ejection interrupt.
Proceed similarly before launching the eject handler as a consequence of
detecting an invalid insert interrupt.
Fixes: aab1ad11d6 ("ASoC: nau8821: new driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251003-nau8821-jdet-fixes-v1-1-f7b0e2543f09@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6370a996f3 ]
The gain ranges specified in Renesas IDT821034 codec documentation
are [-3dB;+13dB] in the transmit path (ADC) and [-13dB;+3dB] in the
receive path (DAC). Allthough the registers allow programming values
outside those ranges, the signal S/N and distorsion are only
guaranteed in the specified ranges.
Set ranges to the specified ones.
Fixes: e51166990e ("ASoC: codecs: Add support for the Renesas IDT821034 codec")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://patch.msgid.link/2bd547194f3398e6182f770d7d6be711c702b4b2.1760029099.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bace10b596 upstream.
Assumption that chain DMA module starts the link DMA when 1ms of
data is available from host is not correct. Instead the firmware
chain DMA module fills the link DMA with initial buffer of zeroes
and the host and link DMAs are started at the same time.
This results in a small error in delay calculation. This can become a
more severe problem if host DMA has delays that exceed 1ms. This results
in negative delay to be calculated and bogus values reported to
applications. This can confuse some applications like
alsa_conformance_test.
Fix the issue by correctly calculating the firmware chain DMA
preamble size and initializing the start offset to this value.
Cc: stable@vger.kernel.org
Fixes: a1d203d390 ("ASoC: SOF: ipc4-pcm: Enable delay reporting for ChainDMA streams")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20251002074719.2084-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bcd1383516 ]
When the sampling rates going in (host) and out (dai) from the DSP
are different, the IPC4 delay reporting does not work correctly.
Add support for this case by scaling the all raw position values to
a common timebase before calculating real-time delay for the PCM.
Cc: stable@vger.kernel.org
Fixes: 0ea06680df ("ASoC: SOF: ipc4-pcm: Correct the delay calculation")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20251002074719.2084-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1d203d390 ]
All streams (currently) which is configured to use ChainDMA can only work
on Link/host DMA pairs where the link side position can be access via host
registers (like HDA on CAVS 2.5 platforms).
Since the firmware does not provide time_info for ChainDMA, unlike for HDA
stream, the kernel should calculate the start and end offsets that is
needed for the delay calculation.
With this small change we can report accurate delays when the stream is
configured to use ChainDMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20250619102848.12389-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: bcd1383516 ("ASoC: SOF: ipc4-pcm: fix delay calculation when DSP resamples")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aaab61de1f ]
It is allowed to mix Link and Host DMA channels in a way that their index
is different. In this case we would read the LLP from a channel which is
not used or used for other operation.
Such case can be reproduced on cAVS2.5 or ACE1 platforms with soundwire
configuration:
playback to SDW would take Host channel 0 (stream_tag 1) and no Link DMA
used
Second playback to HDMI (HDA) would use Host channel 1 (stream_tag 2) and
Link channel 0 (stream_tag 1).
In this case reading the LLP from channel 2 is incorrect as that is not the
Link channel used for the HDMI playback.
To correct this, we should look up the BE and get the channel used on the
Link side.
Fixes: 67b182bea0 ("ASoC: SOF: Intel: hda: Implement get_stream_position (Linear Link Position)")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20251002074719.2084-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45ad27d9a6 ]
Instead of constraining the ALSA buffer time to be double of the firmware
host buffer size, it is better to set it for the period time.
This will implicitly constrain the buffer time to a safe value
(num_periods is at least 2) and prohibits applications to set smaller
period size than what will be covered by the initial DMA burst.
Fixes: fe76d2e75a ("ASoC: SOF: Intel: hda-pcm: Use dsp_max_burst_size_in_ms to place constraint")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251002135752.2430-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dcf683bf1 ]
For ChainDMA the firmware allocates 5ms host buffer instead of the standard
4ms which should be taken into account when setting the constraint on the
buffer size.
Fixes: 842bb8b62c ("ASoC: SOF: ipc4-topology: Save the DMA maximum burst size for PCMs")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251002135752.2430-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7fe5ff832 ]
The firmware has changed the minimum host buffer size from 2 periods to
4 periods (1 period is 1ms) which was missed by the kernel side.
Adjust the SOF_IPC4_MIN_DMA_BUFFER_SIZE to 4 ms to align with firmware.
Link: f0a14a3f41
Fixes: 594c1bb9ff ("ASoC: SOF: ipc4-topology: Do not parse the DMA_BUFFER_SIZE token")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251002135752.2430-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4bb62eb59 upstream.
For some reason we ended up with stub functions that are not inline,
this can result in build error if its included multiple places, as we will
be redefining the same function
Fixes: c99a515ff1 ("ASoC: codecs: wcd937x-sdw: add SoundWire driver")
Cc: Stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20250909121954.225833-3-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66a940b1bf upstream.
For some reason we endup with setting soundwire port for
HPHL_COMP and HPHR_COMP as zero, this can potentially result
in a memory corruption due to accessing and setting -1 th element of
port_map array.
Fixes: 82be8c62a3 ("ASoC: codecs: wcd937x: add basic controls")
Cc: Stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20250909121954.225833-2-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59abe7bc7e upstream.
In the case of static pipelines, freeing the widgets in the pipelines
that were not suspended after freeing the scheduler widgets results in
errors because the secondary cores are powered off when the scheduler
widgets are freed. Fix this by tearing down the leftover pipelines before
powering off the secondary cores.
Cc: stable@vger.kernel.org
Fixes: d7332c4a4f ("ASoC: SOF: ipc3-topology: Fix pipeline tear down logic")
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20251002073125.32471-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e65bda827 upstream.
wcd934x_codec_parse_data() contains a device reference count leak in
of_slim_get_device() where device_find_child() increases the reference
count of the device but this reference is not properly decreased in
the success path. Add put_device() in wcd934x_codec_parse_data() and
add devm_add_action_or_reset() in the probe function, which ensures
that the reference count of the device is correctly managed.
Memory leak in regmap_init_slimbus() as the allocated regmap is not
released when the device is removed. Using devm_regmap_init_slimbus()
instead of regmap_init_slimbus() to ensure automatic regmap cleanup on
device removal.
Calling path: of_slim_get_device() -> of_find_slim_device() ->
device_find_child(). As comment of device_find_child() says, 'NOTE:
you will need to drop the reference with put_device() after use.'.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: a61f3b4f47 ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250923065212.26660-1-make24@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87cab86925 ]
In create_sdw_dailink() check that sof_end->codec_info->add_sidecar
is not NULL before calling it.
The original code assumed that if include_sidecar is true, the codec
on that link has an add_sidecar callback. But there could be other
codecs on the same link that do not have an add_sidecar callback.
Fixes: da52441802 ("ASoC: Intel: sof_sdw: Add callbacks to register sidecar devices")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250919140235.1071941-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fc4a3da9a ]
snd_pcm_group_lock_irq() acquires a spinlock_t and disables interrupts
via spin_lock_irq(). This also implicitly disables the handling of
softirqs such as TIMER_SOFTIRQ.
On PREEMPT_RT softirqs are preemptible and spin_lock_irq() does not
disable them. That means a timer can be invoked during spin_lock_irq()
on the same CPU. Due to synchronisations reasons local_bh_disable() has
a per-CPU lock named softirq_ctrl.lock which synchronizes individual
softirq against each other.
syz-bot managed to trigger a lockdep report where softirq_ctrl.lock is
acquired in hrtimer_cancel() in addition to hrtimer_run_softirq(). This
is a possible deadlock.
The softirq_ctrl.lock can not be made part of spin_lock_irq() as this
would lead to too much synchronisation against individual threads on the
system. To avoid the possible deadlock, softirqs must be manually
disabled before the lock is acquired.
Disable softirqs before the lock is acquired on PREEMPT_RT.
Reported-by: syzbot+10b4363fb0f46527f3f3@syzkaller.appspotmail.com
Fixes: d2d6422f8b ("x86: Allow to enable PREEMPT_RT.")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4336efb59e ]
When an invalid value is passed via quirk option, currently
bytcr_rt5640 driver just ignores and leaves as is, which may lead to
unepxected results like OOB access.
This patch adds the sanity check and corrects the input mapping to the
certain default value if an invalid value is passed.
Fixes: 64484ccee7 ("ASoC: Intel: bytcr_rt5651: Set card long_name based on quirks")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20250902171826.27329-4-tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fba404e4b4 ]
When an invalid value is passed via quirk option, currently
bytcr_rt5640 driver only shows an error message but leaves as is.
This may lead to unepxected results like OOB access.
This patch corrects the input mapping to the certain default value if
an invalid value is passed.
Fixes: 063422ca2a ("ASoC: Intel: bytcr_rt5640: Set card long_name based on quirks")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20250902171826.27329-3-tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b20eb0e8de ]
When an invalid value is passed via quirk option, currently
bytcht_es8316 driver just ignores and leaves as is, which may lead to
unepxected results like OOB access.
This patch adds the sanity check and corrects the input mapping to the
certain default value if an invalid value is passed.
Fixes: 249d2fc9e5 ("ASoC: Intel: bytcht_es8316: Set card long_name based on quirks")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20250902171826.27329-2-tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ef353d546 ]
Change the 'ret' variable from u16 to int to store negative error codes or
zero returned by lx_message_send_atomic().
Storing the negative error codes in unsigned type, doesn't cause an issue
at runtime but it's ugly as pants. Additionally, assigning negative error
codes to unsigned type may trigger a GCC warning when the -Wsign-conversion
flag is enabled.
No effect on runtime.
Fixes: 02bec49045 ("ALSA: lx6464es - driver for the digigram lx6464es interface")
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Link: https://patch.msgid.link/20250828081312.393148-1-rongqianfeng@vivo.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9f2c0ac142 upstream.
The previous commit 0718a78f6a ("ALSA: usb-audio: Kill timer properly at
removal") patched a UAF issue caused by the error timer.
However, because the error timer kill added in this patch occurs after the
endpoint delete, a race condition to UAF still occurs, albeit rarely.
Additionally, since kill-cleanup for urb is also missing, freed memory can
be accessed in interrupt context related to urb, which can cause UAF.
Therefore, to prevent this, error timer and urb must be killed before
freeing the heap memory.
Cc: <stable@vger.kernel.org>
Reported-by: syzbot+f02665daa2abeef4a947@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f02665daa2abeef4a947
Fixes: 0718a78f6a ("ALSA: usb-audio: Kill timer properly at removal")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0718a78f6a upstream.
The USB-audio MIDI code initializes the timer, but in a rare case, the
driver might be freed without the disconnect call. This leaves the
timer in an active state while the assigned object is released via
snd_usbmidi_free(), which ends up with a kernel warning when the debug
configuration is enabled, as spotted by fuzzer.
For avoiding the problem, put timer_shutdown_sync() at
snd_usbmidi_free(), so that the timer can be killed properly.
While we're at it, replace the existing timer_delete_sync() at the
disconnect callback with timer_shutdown_sync(), too.
Reported-by: syzbot+d8f72178ab6783a7daea@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/681c70d7.050a0220.a19a9.00c6.GAE@google.com
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20250519212031.14436-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[ del_timer vs timer_delete differences ]
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1dd28fd86c ]
Adjust register settings for SAR adc button detection mode
to fix noise issue in headset.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://patch.msgid.link/766cd1d2dd7a403ba65bb4cc44845f71@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1d0260362 ]
Set pdm gain value by setting PDM_MISC_CTRL_MASK value.
To avoid low pdm gain value.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20250821054606.1279178-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8318e04ab2 upstream.
It is possible that the topology parsing function
audioreach_widget_load_module_common() could return NULL or an error
pointer. Add missing NULL check so that we do not dereference it.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: Stable@vger.kernel.org
Fixes: 36ad9bf1d9 ("ASoC: qdsp6: audioreach: add topology support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20250825101247.152619-2-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9df175548 ]
The vendor Comtrue Inc. (0x2fc6) produces USB audio chipsets like
the CT7601 which are capable of Native DSD playback.
This patch adds QUIRK_FLAG_DSD_RAW for Comtrue (VID 0x2fc6), which enables
native DSD playback (DSD_U32_LE) on their USB Audio device. This has been
verified under Ubuntu 25.04 with JRiver.
Signed-off-by: noble.yang <noble.yang@comtrue-inc.com>
Link: https://patch.msgid.link/20250731110614.4070-1-noble228@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
