commit 4541b0c8c3 upstream.
Currently, RX is_mcbc bit is set for packets sent from client as
destination address (DA) is multicast/broadcast address, but packets
are actually unicast as receiver address (RA) is not multicast address.
Hence, packets are not handled properly due to this is_mcbc bit.
Therefore, reset the is_mcbc bit if interface type is AP.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411061523.859387-3-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
[ Adjust context ]
Signed-off-by: Oliver Sedlbauer <os@dev.tdt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f80e21bf6 ]
If a port interrupt setup fails after at least one port has already been
successfully initialized, the gotos miss some resource releasing:
- the already initialized PTP IRQs aren't released
- the already initialized port IRQs aren't released if the failure
occurs in ksz_pirq_setup().
Merge 'out_girq' and 'out_ptpirq' into a single 'port_release' label.
Behind this label, use the reverse loop to release all IRQ resources
for all initialized ports.
Jump in the middle of the reverse loop if an error occurs in
ksz_ptp_irq_setup() to only release the port IRQ of the current
iteration.
Cc: stable@vger.kernel.org
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-4-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ed3472173 ]
The PTP driver code only works for certain KSZ switches like KSZ9477,
KSZ9567, LAN937X and their varieties. This code is enabled by kernel
configuration CONFIG_NET_DSA_MICROCHIP_KSZ_PTP. As the DSA driver is
common to work with all KSZ switches this PTP code is not appropriate
for other unsupported switches. The ptp_capable indication is added to
the chip data structure to signal whether to execute those code.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241218020240.70601-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 0f80e21bf6 ("net: dsa: microchip: Free previously initialized ports on init failures")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0b8fec8ae ]
The IRQ numbers created through irq_create_mapping() are only assigned
to ptpmsg_irq[n].num at the end of the IRQ setup. So if an error occurs
between their creation and their assignment (for instance during the
request_threaded_irq() step), we enter the error path and fail to
release the newly created virtual IRQs because they aren't yet assigned
to ptpmsg_irq[n].num.
Move the mapping creation to ksz_ptp_msg_irq_setup() to ensure symetry
with what's released by ksz_ptp_msg_irq_free().
In the error path, move the irq_dispose_mapping to the out_ptp_msg label
so it will be called only on created IRQs.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-5-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d849ff573 ]
The commit 5cff263606 ("can: rcar_canfd: Fix controller mode setting")
has aligned with the flow mentioned in the hardware manual for all SoCs
except R-Car Gen3 and RZ/G2L SoCs. On R-Car Gen4 and RZ/G3E SoCs, due to
the wrong logic in the commit[1] sets the default mode to FD-Only mode
instead of CAN-FD mode.
This patch sets the CAN-FD mode as the default for all SoCs by dropping
the rcar_canfd_set_mode() as some SoC requires mode setting in global
reset mode, and the rest of the SoCs in channel reset mode and update the
rcar_canfd_reset_controller() to take care of these constraints. Moreover,
the RZ/G3E and R-Car Gen4 SoCs support 3 modes compared to 2 modes on the
R-Car Gen3. Use inverted logic in rcar_canfd_reset_controller() to
simplify the code later to support FD-only mode.
[1]
commit 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Fixes: 5cff263606 ("can: rcar_canfd: Fix controller mode setting")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20251118123926.193445-1-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[ adapted to use existing is_gen4() helper and RCANFD_GEN4_FDCFG() macro instead of new ch_interface_mode field and fcbase struct ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25b62cc5b2 upstream.
If something goes wrong at setup, ksz_irq_free() can be called on
uninitialized ksz_irq (for example when ksz_ptp_irq_setup() fails). It
leads to freeing uninitialized IRQ numbers and/or domains.
Use dsa_switch_for_each_user_port_continue_reverse() in the error path
to iterate only over the fully initialized ports.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-3-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e059305be upstream.
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, during the PTP IRQ setup,
we verify that its returned value isn't negative.
Fix the irq_find_mapping() check to enter the error path when 0 is
returned. Return -EINVAL in such case.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-2-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b3c09e166 upstream.
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, on each
irq_find_mapping() call, we verify that the returned value isn't
negative.
Fix the irq_find_mapping() checks to enter error paths when 0 is
returned. Return -EINVAL in such cases.
CC: stable@vger.kernel.org
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-1-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76544beea7 upstream.
Reading the interrupt register `SUN4I_REG_INT_ADDR` causes all of its bits
to be reset. If we ever reach the condition of handling more than
`SUN4I_CAN_MAX_IRQ` IRQs, we will have read the register and reset all its
bits but without actually handling the interrupt inside of the loop body.
This may, among other issues, cause us to never `netif_wake_queue()` again
after a transmission interrupt.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Cc: stable@vger.kernel.org
Co-developed-by: Thomas Mühlbacher <tmuehlbacher@posteo.net>
Signed-off-by: Thomas Mühlbacher <tmuehlbacher@posteo.net>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251116-sun4i-fix-loop-v1-1-3d76d3f81950@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30db4451c7 upstream.
Reading the interrupt register `SJA1000_IR` causes all of its bits to be
reset. If we ever reach the condition of handling more than
`SJA1000_MAX_IRQ` IRQs, we will have read the register and reset all its
bits but without actually handling the interrupt inside of the loop
body.
This may, among other issues, cause us to never `netif_wake_queue()`
again after a transmission interrupt.
Fixes: 429da1cc84 ("can: Driver for the SJA1000 CAN controller")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Mühlbacher <tmuehlbacher@posteo.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20251115153437.11419-1-tmuehlbacher@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a060d0fac ]
There are currently two situations that can trigger the PTP interrupt,
one is the PPS event, the other is the PEROUT event. However, the irq
handler fec_pps_interrupt() does not check the irq event type and
directly registers a PPS event into the system, but the event may be
a PEROUT event. This is incorrect because PEROUT is an output signal,
while PPS is the input of the kernel PPS system. Therefore, add a check
for the event type, if pps_enable is true, it means that the current
event is a PPS event, and then the PPS event is registered.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-5-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0a1f3d7e1 ]
In the current driver, PPS and PEROUT use the same channel to generate
the events, so they cannot be enabled at the same time. Otherwise, the
later configuration will overwrite the earlier configuration. Therefore,
when configuring PPS, the driver will check whether PEROUT is enabled.
Similarly, when configuring PEROUT, the driver will check whether PPS
is enabled.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-4-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e97faa0c20 ]
If the previously set PEROUT is already active, updating it will cause
the new PEROUT to start immediately instead of at the specified time.
This is because fep->reload_period is updated whithout check whether
the PEROUT is enabled, and the old PEROUT is not disabled. Therefore,
the pulse period will be updated immediately in the pulse interrupt
handler fec_pps_interrupt().
Currently, the driver does not support directly updating PEROUT and it
will make the logic be more complicated. To fix the current issue, add
a check before enabling the PEROUT, the driver will return an error if
PEROUT is enabled. If users wants to update a new PEROUT, they should
disable the old PEROUT first.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50caa74468 ]
The PEROUT allows the user to set a specified future time to output the
periodic signal. If the future time is far from the current time, the FEC
driver will use hrtimer to configure PEROUT one second before the future
time. However, the hrtimer will not be canceled if the PEROUT is disabled
before the hrtimer expires. So the PEROUT will be configured when the
hrtimer expires, which is not as expected. Therefore, cancel the hrtimer
in fec_ptp_pps_disable() to fix this issue.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ffcb7b890 ]
The atlantic driver can receive packets with more than MAX_SKB_FRAGS (17)
fragments when handling large multi-descriptor packets. This causes an
out-of-bounds write in skb_add_rx_frag_netmem() leading to kernel panic.
The issue occurs because the driver doesn't check the total number of
fragments before calling skb_add_rx_frag(). When a packet requires more
than MAX_SKB_FRAGS fragments, the fragment index exceeds the array bounds.
Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE,
then all fragments are accounted for. And reusing the existing check to
prevent the overflow earlier in the code path.
This crash occurred in production with an Aquantia AQC113 10G NIC.
Stack trace from production environment:
```
RIP: 0010:skb_add_rx_frag_netmem+0x29/0xd0
Code: 90 f3 0f 1e fa 0f 1f 44 00 00 48 89 f8 41 89
ca 48 89 d7 48 63 ce 8b 90 c0 00 00 00 48 c1 e1 04 48 01 ca 48 03 90
c8 00 00 00 <48> 89 7a 30 44 89 52 3c 44 89 42 38 40 f6 c7 01 75 74 48
89 fa 83
RSP: 0018:ffffa9bec02a8d50 EFLAGS: 00010287
RAX: ffff925b22e80a00 RBX: ffff925ad38d2700 RCX:
fffffffe0a0c8000
RDX: ffff9258ea95bac0 RSI: ffff925ae0a0c800 RDI:
0000000000037a40
RBP: 0000000000000024 R08: 0000000000000000 R09:
0000000000000021
R10: 0000000000000848 R11: 0000000000000000 R12:
ffffa9bec02a8e24
R13: ffff925ad8615570 R14: 0000000000000000 R15:
ffff925b22e80a00
FS: 0000000000000000(0000)
GS:ffff925e47880000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9258ea95baf0 CR3: 0000000166022004 CR4:
0000000000f72ef0
PKRU: 55555554
Call Trace:
<IRQ>
aq_ring_rx_clean+0x175/0xe60 [atlantic]
? aq_ring_rx_clean+0x14d/0xe60 [atlantic]
? aq_ring_tx_clean+0xdf/0x190 [atlantic]
? kmem_cache_free+0x348/0x450
? aq_vec_poll+0x81/0x1d0 [atlantic]
? __napi_poll+0x28/0x1c0
? net_rx_action+0x337/0x420
```
Fixes: 6aecbba12b ("net: atlantic: add check for MAX_SKB_FRAGS")
Changes in v4:
- Add Fixes: tag to satisfy patch validation requirements.
Changes in v3:
- Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE,
then all fragments are accounted for.
Signed-off-by: Jiefeng Zhang <jiefeng.z.zhang@gmail.com>
Link: https://patch.msgid.link/20251126032249.69358-1-jiefeng.z.zhang@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d66e093e0 ]
Fix a potential counter roll-over issue in fbnic_mbx_alloc_rx_msgs()
when calculating descriptor slots. The issue occurs when head - tail
results in a large positive value (unsigned) and the compiler interprets
head - tail - 1 as a signed value.
Since FBNIC_IPC_MBX_DESC_LEN is a power of two, use a masking operation,
which is a common way of avoiding this problem when dealing with these
sort of ring space calculations.
Fixes: da3cde0820 ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20251125211704.3222413-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da62abaaa2 ]
When using the SGMII PCS as a fixed-link chip-to-chip connection, it is
easy to miss the fact that traffic passes only at 1G, since that's what
any normal such connection would use.
When using the SGMII PCS connected towards an on-board PHY or an SFP
module, it is immediately noticeable that when the link resolves to a
speed other than 1G, traffic from the MAC fails to pass: TX counters
increase, but nothing gets decoded by the other end, and no local RX
counters increase either.
Artificially lowering a fixed-link rate to speed = <100> makes us able
to see the same issue as in the case of having an SGMII PHY.
Some debugging shows that the XPCS configuration is A-OK, but that the
MAC Configuration Table entry for the port has the SPEED bits still set
to 1000Mbps, due to a special condition in the driver. Deleting that
condition, and letting the resolved link speed be programmed directly
into the MAC speed field, results in a functional link at all 3 speeds.
This piece of evidence, based on testing on both generations with SGMII
support (SJA1105S and SJA1110A) directly contradicts the statement from
the blamed commit that "the MAC is fixed at 1 Gbps and we need to
configure the PCS only (if even that)". Worse, that statement is not
backed by any documentation, and no one from NXP knows what it might
refer to.
I am unable to recall sufficient context regarding my testing from March
2020 to understand what led me to draw such a braindead and factually
incorrect conclusion. Yet, there is nothing of value regarding forcing
the MAC speed, either for SGMII or 2500Base-X (introduced at a later
stage), so remove all such logic.
Fixes: ffe10e679c ("net: dsa: sja1105: Add support for the SGMII port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251122111324.136761-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a18891b557 ]
The static configuration reload saves the port speed in the static
configuration tables by first converting it from the internal
respresentation to the SPEED_xxx ethtool representation, and then
converts it back to restore the setting. This is because
sja1105_adjust_port_config() takes the speed as SPEED_xxx.
However, this is unnecessarily complex. If we split
sja1105_adjust_port_config() up, we can simply save and restore the
mac[port].speed member in the static configuration tables.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMa-005ZIX-If@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: da62abaaa2 ("net: dsa: sja1105: fix SGMII linking at 10M or 100M but not passing traffic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fcb8ab4a0 ]
Correct it since M.2 device T99W640 has updated from T99W515.
We need to align it with MHI side otherwise this modem can't
get the network.
Fixes: ae5a342643 ("bus: mhi: host: pci_generic: Fix the modem name of Foxconn T99W640")
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20251125070900.33324-1-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5bce28f6b ]
Currently, when skb is null, the driver prints an error and then
dereferences skb on the next line.
To fix this, let's add a 'break' after the error message to switch
to sxgbe_rx_refill(), which is similar to the approach taken by the
other drivers in this particular case, e.g. calxeda with xgmac_rx().
Found during a code review.
Fixes: 1edb9ca69e ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121123834.97748-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ae9cfc454 ]
Attempting to add a port device that is already up will expectedly fail,
but not before modifying the team device header_ops.
In the case of the syzbot reproducer the gre0 device is
already in state UP when it attempts to add it as a
port device of team0, this fails but before that
header_ops->create of team0 is changed from eth_header to ipgre_header
in the call to team_dev_type_check_change.
Later when we end up in ipgre_header() struct ip_tunnel* points to nonsense
as the private data of the device still holds a struct team.
Example sequence of iproute2 commands to reproduce the hang/BUG():
ip link add dev team0 type team
ip link add dev gre0 type gre
ip link set dev gre0 up
ip link set dev gre0 master team0
ip link set dev team0 up
ping -I team0 1.1.1.1
Move team_dev_type_check_change down where all other checks have passed
as it changes the dev type with no way to restore it in case
one of the checks that follow it fail.
Also make sure to preserve the origial mtu assignment:
- If port_dev is not the same type as dev, dev takes mtu from port_dev
- If port_dev is the same type as dev, port_dev takes mtu from dev
This is done by adding a conditional before the call to dev_set_mtu
to prevent it from assigning port_dev->mtu = dev->mtu and instead
letting team_dev_type_check_change assign dev->mtu = port_dev->mtu.
The conditional is needed because the patch moves the call to
team_dev_type_check_change past dev_set_mtu.
Testing:
- team device driver in-tree selftests
- Add/remove various devices as slaves of team device
- syzbot
Reported-by: syzbot+a2a3b519de727b0f7903@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a2a3b519de727b0f7903
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Signed-off-by: Nikola Z. Ivanov <zlatistiv@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20251122002027.695151-1-zlatistiv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2099d9f16 ]
The rate limiting validation condition currently checks the output
variable max_bw_value[i] instead of the input value
maxrate->tc_maxrate[i]. This causes the validation to compare an
uninitialized or stale value rather than the actual requested rate.
The condition should check the input rate to properly validate against
the upper limit:
} else if (maxrate->tc_maxrate[i] <= upper_limit_gbps) {
This aligns with the pattern used in the first branch, which correctly
checks maxrate->tc_maxrate[i] against upper_limit_mbps.
The current implementation can lead to unreliable validation behavior:
- For rates between 25.5 Gbps and 255 Gbps, if max_bw_value[i] is 0
from initialization, the GBPS path may be taken regardless of whether
the actual rate is within bounds
- When processing multiple TCs (i > 0), max_bw_value[i] contains the
value computed for the previous TC, affecting the validation logic
- The overflow check for rates exceeding 255 Gbps may not trigger
consistently depending on previous array values
This patch ensures the validation correctly examines the requested rate
value for proper bounds checking.
Fixes: 43b27d1bd8 ("net/mlx5e: Fix wraparound in rate limiting for values above 255 Gbps")
Signed-off-by: Danielle Costantino <dcostantino@meta.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20251124180043.2314428-1-dcostantino@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9780f535f8 ]
To initialize the taprio block in lan966x, it is required to configure
the register REVISIT_DLY. The purpose of this register is to set the
delay before revisit the next gate and the value of this register depends
on the system clock. The problem is that the we calculated wrong the value
of the system clock period in picoseconds. The actual system clock is
~165.617754MHZ and this correspond to a period of 6038 pico seconds and
not 15125 as currently set.
Fixes: e462b27173 ("net: lan966x: Add offload support for taprio")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121061411.810571-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec3803b591 ]
As the interface mode doesn't need to be updated on PHYs connected with
USXGMII and integrated PHYs, gpy_update_interface() should just return 0
in these cases rather than -EINVAL which has wrongly been introduced by
commit 7a495dde27 ("net: phy: mxl-gpy: Change gpy_update_interface()
function return type"), as this breaks support for those PHYs.
Fixes: 7a495dde27 ("net: phy: mxl-gpy: Change gpy_update_interface() function return type")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/f744f721a1fcc5e2e936428c62ff2c7d94d2a293.1763648168.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a14602fcae ]
As explain in commit fa349e396e ("veth: Fix race with AF_XDP exposing
old or uninitialized descriptors") for veth there is a chance after
napi_complete_done() that another CPU can manage start another NAPI
instance running veth_pool(). For NAPI this is correctly handled as the
napi_schedule_prep() check will prevent multiple instances from getting
scheduled, but for the remaining code in veth_pool() this can run
concurrent with the newly started NAPI instance.
The problem/race is that xdp_clear_return_frame_no_direct() isn't
designed to be nested.
Prior to commit 401cb7dae8 ("net: Reference bpf_redirect_info via
task_struct on PREEMPT_RT.") the temporary BPF net context
bpf_redirect_info was stored per CPU, where this wasn't an issue. Since
this commit the BPF context is stored in 'current' task_struct. When
running veth in threaded-NAPI mode, then the kthread becomes the storage
area. Now a race exists between two concurrent veth_pool() function calls
one exiting NAPI and one running new NAPI, both using the same BPF net
context.
Race is when another CPU gets within the xdp_set_return_frame_no_direct()
section before exiting veth_pool() calls the clear-function
xdp_clear_return_frame_no_direct().
Fixes: 401cb7dae8 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/176356963888.337072.4805242001928705046.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5442a9da69 ]
Commit dc82a33297 ("veth: apply qdisc backpressure on full ptr_ring to
reduce TX drops") introduced a race condition that can lead to a permanently
stalled TXQ. This was observed in production on ARM64 systems (Ampere Altra
Max).
The race occurs in veth_xmit(). The producer observes a full ptr_ring and
stops the queue (netif_tx_stop_queue()). The subsequent conditional logic,
intended to re-wake the queue if the consumer had just emptied it (if
(__ptr_ring_empty(...)) netif_tx_wake_queue()), can fail. This leads to a
"lost wakeup" where the TXQ remains stopped (QUEUE_STATE_DRV_XOFF) and
traffic halts.
This failure is caused by an incorrect use of the __ptr_ring_empty() API
from the producer side. As noted in kernel comments, this check is not
guaranteed to be correct if a consumer is operating on another CPU. The
empty test is based on ptr_ring->consumer_head, making it reliable only for
the consumer. Using this check from the producer side is fundamentally racy.
This patch fixes the race by adopting the more robust logic from an earlier
version V4 of the patchset, which always flushed the peer:
(1) In veth_xmit(), the racy conditional wake-up logic and its memory barrier
are removed. Instead, after stopping the queue, we unconditionally call
__veth_xdp_flush(rq). This guarantees that the NAPI consumer is scheduled,
making it solely responsible for re-waking the TXQ.
This handles the race where veth_poll() consumes all packets and completes
NAPI *before* veth_xmit() on the producer side has called netif_tx_stop_queue.
The __veth_xdp_flush(rq) will observe rx_notify_masked is false and schedule
NAPI.
(2) On the consumer side, the logic for waking the peer TXQ is moved out of
veth_xdp_rcv() and placed at the end of the veth_poll() function. This
placement is part of fixing the race, as the netif_tx_queue_stopped() check
must occur after rx_notify_masked is potentially set to false during NAPI
completion.
This handles the race where veth_poll() consumes all packets, but haven't
finished (rx_notify_masked is still true). The producer veth_xmit() stops the
TXQ and __veth_xdp_flush(rq) will observe rx_notify_masked is true, meaning
not starting NAPI. Then veth_poll() change rx_notify_masked to false and
stops NAPI. Before exiting veth_poll() will observe TXQ is stopped and wake
it up.
Fixes: dc82a33297 ("veth: apply qdisc backpressure on full ptr_ring to reduce TX drops")
Reviewed-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/176295323282.307447.14790015927673763094.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a14602fcae ("veth: reduce XDP no_direct return section to fix race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc82a33297 ]
In production, we're seeing TX drops on veth devices when the ptr_ring
fills up. This can occur when NAPI mode is enabled, though it's
relatively rare. However, with threaded NAPI - which we use in
production - the drops become significantly more frequent.
The underlying issue is that with threaded NAPI, the consumer often runs
on a different CPU than the producer. This increases the likelihood of
the ring filling up before the consumer gets scheduled, especially under
load, leading to drops in veth_xmit() (ndo_start_xmit()).
This patch introduces backpressure by returning NETDEV_TX_BUSY when the
ring is full, signaling the qdisc layer to requeue the packet. The txq
(netdev queue) is stopped in this condition and restarted once
veth_poll() drains entries from the ring, ensuring coordination between
NAPI and qdisc.
Backpressure is only enabled when a qdisc is attached. Without a qdisc,
the driver retains its original behavior - dropping packets immediately
when the ring is full. This avoids unexpected behavior changes in setups
without a configured qdisc.
With a qdisc in place (e.g. fq, sfq) this allows Active Queue Management
(AQM) to fairly schedule packets across flows and reduce collateral
damage from elephant flows.
A known limitation of this approach is that the full ring sits in front
of the qdisc layer, effectively forming a FIFO buffer that introduces
base latency. While AQM still improves fairness and mitigates flow
dominance, the latency impact is measurable.
In hardware drivers, this issue is typically addressed using BQL (Byte
Queue Limits), which tracks in-flight bytes needed based on physical link
rate. However, for virtual drivers like veth, there is no fixed bandwidth
constraint - the bottleneck is CPU availability and the scheduler's ability
to run the NAPI thread. It is unclear how effective BQL would be in this
context.
This patch serves as a first step toward addressing TX drops. Future work
may explore adapting a BQL-like mechanism to better suit virtual devices
like veth.
Reported-by: Yan Zhai <yan@cloudflare.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Link: https://patch.msgid.link/174559294022.827981.1282809941662942189.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a14602fcae ("veth: reduce XDP no_direct return section to fix race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34dd0fecaa ]
The "noqueue" qdisc can either be directly attached, or get default
attached if net_device priv_flags has IFF_NO_QUEUE. In both cases, the
allocated Qdisc structure gets it's enqueue function pointer reset to
NULL by noqueue_init() via noqueue_qdisc_ops.
This is a common case for software virtual net_devices. For these devices
with no-queue, the transmission path in __dev_queue_xmit() will bypass
the qdisc layer. Directly invoking device drivers ndo_start_xmit (via
dev_hard_start_xmit). In this mode the device driver is not allowed to
ask for packets to be queued (either via returning NETDEV_TX_BUSY or
stopping the TXQ).
The simplest and most reliable way to identify this no-queue case is by
checking if enqueue == NULL.
The vrf driver currently open-codes this check (!qdisc->enqueue). While
functionally correct, this low-level detail is better encapsulated in a
dedicated helper for clarity and long-term maintainability.
To make this behavior more explicit and reusable, this patch introduce a
new helper: qdisc_txq_has_no_queue(). Helper will also be used by the
veth driver in the next patch, which introduces optional qdisc-based
backpressure.
This is a non-functional change.
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/174559293172.827981.7583862632045264175.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a14602fcae ("veth: reduce XDP no_direct return section to fix race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 395d988f93 ]
The URB received in gs_usb_receive_bulk_callback() contains a struct
gs_host_frame. The length of the data after the header depends on the
gs_host_frame hf::flags and the active device features (e.g. time
stamping).
Introduce a new function gs_usb_get_minimum_length() and check that we have
at least received the required amount of data before accessing it. Only
copy the data to that skb that has actually been received.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://patch.msgid.link/20251114-gs_usb-fix-usb-callbacks-v1-3-a29b42eacada@pengutronix.de
[mkl: rename gs_usb_get_minimum_length() -> +gs_usb_get_minimum_rx_length()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fe9f3279f ]
The driver expects to receive a struct gs_host_frame in
gs_usb_receive_bulk_callback().
Use struct_group to describe the header of the struct gs_host_frame and
check that we have at least received the header before accessing any
members of it.
To resubmit the URB, do not dereference the pointer chain
"dev->parent->hf_size_rx" but use "parent->hf_size_rx" instead. Since
"urb->context" contains "parent", it is always defined, while "dev" is not
defined if the URB it too short.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://patch.msgid.link/20251114-gs_usb-fix-usb-callbacks-v1-2-a29b42eacada@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 516a0cd1c0 ]
The driver lacks the cleanup of failed transfers of URBs. This reduces the
number of available URBs per error by 1. This leads to reduced performance
and ultimately to a complete stop of the transmission.
If the sending of a bulk URB fails do proper cleanup:
- increase netdev stats
- mark the echo_sbk as free
- free the driver's context and do accounting
- wake the send queue
Closes: https://github.com/candle-usb/candleLight_fw/issues/187
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://patch.msgid.link/20251114-gs_usb-fix-usb-callbacks-v1-1-a29b42eacada@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c73772cd2 ]
The `kvaser_usb_leaf_wait_cmd()` and `kvaser_usb_leaf_read_bulk_callback`
functions contain logic to zero-length commands. These commands are used
to align data to the USB endpoint's wMaxPacketSize boundary.
The driver attempts to skip these placeholders by aligning the buffer
position `pos` to the next packet boundary using `round_up()` function.
However, if zero-length command is found exactly on a packet boundary
(i.e., `pos` is a multiple of wMaxPacketSize, including 0), `round_up`
function will return the unchanged value of `pos`. This prevents `pos`
to be increased, causing an infinite loop in the parsing logic.
This patch fixes this in the function by using `pos + 1` instead.
This ensures that even if `pos` is on a boundary, the calculation is
based on `pos + 1`, forcing `round_up()` to always return the next
aligned boundary.
Fixes: 7259124eac ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c")
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Reviewed-by: Jimmy Assarsson <extja@kvaser.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20251023162709.348240-1-eeodqql09@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90a88306eb ]
Make knav_dma_open_channel consistently return NULL on error instead
of ERR_PTR. Currently the header include/linux/soc/ti/knav_dma.h
returns NULL when the driver is disabled, but the driver
implementation does not even return NULL or ERR_PTR on failure,
causing inconsistency in the users. This results in a crash in
netcp_free_navigator_resources as followed (trimmed):
Unhandled fault: alignment exception (0x221) at 0xfffffff2
[fffffff2] *pgd=80000800207003, *pmd=82ffda003, *pte=00000000
Internal error: : 221 [#1] SMP ARM
Modules linked in:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.17.0-rc7 #1 NONE
Hardware name: Keystone
PC is at knav_dma_close_channel+0x30/0x19c
LR is at netcp_free_navigator_resources+0x2c/0x28c
[... TRIM...]
Call trace:
knav_dma_close_channel from netcp_free_navigator_resources+0x2c/0x28c
netcp_free_navigator_resources from netcp_ndo_open+0x430/0x46c
netcp_ndo_open from __dev_open+0x114/0x29c
__dev_open from __dev_change_flags+0x190/0x208
__dev_change_flags from netif_change_flags+0x1c/0x58
netif_change_flags from dev_change_flags+0x38/0xa0
dev_change_flags from ip_auto_config+0x2c4/0x11f0
ip_auto_config from do_one_initcall+0x58/0x200
do_one_initcall from kernel_init_freeable+0x1cc/0x238
kernel_init_freeable from kernel_init+0x1c/0x12c
kernel_init from ret_from_fork+0x14/0x38
[... TRIM...]
Standardize the error handling by making the function return NULL on
all error conditions. The API is used in just the netcp_core.c so the
impact is limited.
Note, this change, in effect reverts commit 5b6cb43b4d ("net:
ethernet: ti: netcp_core: return error while dma channel open issue"),
but provides a less error prone implementation.
Suggested-by: Simon Horman <horms@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251103162811.3730055-1-nm@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34892cfec0 ]
Update tls_offload_rx_resync_async_request_start() and
tls_offload_rx_resync_async_request_end() to get a struct
tls_offload_resync_async parameter directly, rather than
extracting it from struct sock.
This change aligns the function signatures with the upcoming
tls_offload_rx_resync_async_request_cancel() helper, which
will be introduced in a subsequent patch.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1761508983-937977-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23a5b9b12d ]
Improve the cleanup on releasing PTP resources in error path.
The error case might happen either at the driver probe and PTP
feature initialization or on PTP restart (errors in reset handling, NVM
update etc). In both cases, calls to PF PTP cleanup (ice_ptp_cleanup_pf
function) and 'ps_lock' mutex deinitialization were missed.
Additionally, ptp clock was not unregistered in the latter case.
Keep PTP state as 'uninitialized' on init to distinguish between error
scenarios and to avoid resource release duplication at driver removal.
The consequence of missing ice_ptp_cleanup_pf call is the following call
trace dumped when ice_adapter object is freed (port list is not empty,
as it is required at this stage):
[ T93022] ------------[ cut here ]------------
[ T93022] WARNING: CPU: 10 PID: 93022 at
ice/ice_adapter.c:67 ice_adapter_put+0xef/0x100 [ice]
...
[ T93022] RIP: 0010:ice_adapter_put+0xef/0x100 [ice]
...
[ T93022] Call Trace:
[ T93022] <TASK>
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] ? __warn.cold+0xb0/0x10e
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] ? report_bug+0xd8/0x150
[ T93022] ? handle_bug+0xe9/0x110
[ T93022] ? exc_invalid_op+0x17/0x70
[ T93022] ? asm_exc_invalid_op+0x1a/0x20
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] pci_device_remove+0x42/0xb0
[ T93022] device_release_driver_internal+0x19f/0x200
[ T93022] driver_detach+0x48/0x90
[ T93022] bus_remove_driver+0x70/0xf0
[ T93022] pci_unregister_driver+0x42/0xb0
[ T93022] ice_module_exit+0x10/0xdb0 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
...
[ T93022] ---[ end trace 0000000000000000 ]---
[ T93022] ice: module unloaded
Fixes: e800654e85 ("ice: Use ice_adapter for PTP shared data instead of auxdev")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 896f1a2493 ]
The loops in 'qede_tpa_cont()' and 'qede_tpa_end()', iterate
over 'cqe->len_list[]' using only a zero-length terminator as
the stopping condition. If the terminator was missing or
malformed, the loop could run past the end of the fixed-size array.
Add an explicit bound check using ARRAY_SIZE() in both loops to prevent
a potential out-of-bounds access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 55482edc25 ("qede: Add slowpath/fastpath support and enable hardware GRO")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Link: https://patch.msgid.link/20251113112757.4166625-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0c959fec1 ]
The call to devlink_info_version_fixed_put() in
mlxsw_linecard_devlink_info_get() did not check for errors,
although it is checked everywhere in the code.
Add missed 'err' check to the mlxsw_linecard_devlink_info_get()
Fixes: 3fc0c51905 ("mlxsw: core_linecards: Expose device PSID over device info")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251113161922.813828-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6751b0b19 ]
The LED setup routine registered both led_sync_good
and led_is_gm devices without checking the return
values of led_classdev_register(). If either registration
failed, the function continued silently, leaving the
driver in a partially-initialized state and leaking
a registered LED classdev.
Add proper error handling
Fixes: 7d9ee2e8ff ("net: dsa: hellcreek: Add PTP status LEDs")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20251113135745.92375-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 407a06507c ]
The function mlxsw_sp_flower_stats() calls mlxsw_sp_acl_ruleset_get() to
obtain a ruleset reference. If the subsequent call to
mlxsw_sp_acl_rule_lookup() fails to find a rule, the function returns
an error without releasing the ruleset reference, causing a memory leak.
Fix this by using a goto to the existing error handling label, which
calls mlxsw_sp_acl_ruleset_put() to properly release the reference.
Fixes: 7c1b8eb175 ("mlxsw: spectrum: Add support for TC flower offload statistics")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251112052114.1591695-1-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3ceb6ac211 upstream.
Correct RGMII delay application logic in lan937x_set_tune_adj().
The function was missing `data16 &= ~PORT_TUNE_ADJ` before setting the
new delay value. This caused the new value to be bitwise-OR'd with the
existing PORT_TUNE_ADJ field instead of replacing it.
For example, when setting the RGMII 2 TX delay on port 4, the
intended TUNE_ADJUST value of 0 (RGMII_2_TX_DELAY_2NS) was
incorrectly OR'd with the default 0x1B (from register value 0xDA3),
leaving the delay at the wrong setting.
This patch adds the missing mask to clear the field, ensuring the
correct delay value is written. Physical measurements on the RGMII TX
lines confirm the fix, showing the delay changing from ~1ns (before
change) to ~2ns.
While testing on i.MX 8MP showed this was within the platform's timing
tolerance, it did not match the intended hardware-characterized value.
Fixes: b19ac41faa ("net: dsa: microchip: apply rgmii tx and rx delay in phylink mac config")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20251114090951.4057261-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d277a7a58 upstream.
be_insert_vlan_in_pkt() is called with the wrb_params argument being NULL
at be_send_pkt_to_bmc() call site. This may lead to dereferencing a NULL
pointer when processing a workaround for specific packet, as commit
bc0c3405ab ("be2net: fix a Tx stall bug caused by a specific ipv6
packet") states.
The correct way would be to pass the wrb_params from be_xmit().
Fixes: 760c295e0e ("be2net: Support for OS2BMC.")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://patch.msgid.link/20251119105015.194501-1-a.vatoropin@crpt.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf91f4bc9c upstream.
The blamed commit introduced the function lanphy_modify_page_reg which
as name suggests it, it modifies the registers. In the same commit we
have started to use this function inside the drivers. The problem is
that in the function lan8814_config_init we passed the wrong page number
when disabling the aneg towards host side. We passed extended page number
4(LAN8814_PAGE_COMMON_REGS) instead of extended page
5(LAN8814_PAGE_PORT_REGS)
Fixes: a0de636ed7 ("net: phy: micrel: Introduce lanphy_modify_page_reg")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250925064702.3906950-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f2b28b79d ]
There are actually 2 problems:
- deleting the last element doesn't require the memmove of elements
[i + 1, end) over it. Actually, element i+1 is out of bounds.
- The memmove itself should move size - i - 1 elements, because the last
element is out of bounds.
The out-of-bounds element still remains out of bounds after being
accessed, so the problem is only that we touch it, not that it becomes
in active use. But I suppose it can lead to issues if the out-of-bounds
element is part of an unmapped page.
Fixes: 6666cebc5e ("net: dsa: sja1105: Add support for VLAN operations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Chen Yu <xnguchen@sina.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68410c5bd3 ]
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath11k_pci_alloc_msi(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ. This results in the
below warning:
WARNING: CPU: 7 PID: 349 at kernel/irq/manage.c:1929 free_irq+0x278/0x29c
Call trace:
free_irq+0x278/0x29c
ath11k_pcic_free_irq+0x70/0x10c [ath11k]
ath11k_pci_probe+0x800/0x820 [ath11k_pci]
local_pci_probe+0x40/0xbc
The warning is due to not clearing the affinity hint before freeing the
IRQs.
So to fix this issue, clear the IRQ affinity hint before calling
ath11k_pcic_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Cc: Baochen Qiang <quic_bqiang@quicinc.com>
Fixes: 39564b475a ("wifi: ath11k: fix boot failure with one MSI vector")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250225053447.16824-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Wenshan Lan <jetlan9@163.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
