commit 8a8f3f4991 upstream.
The driver allocates ring elements using GFP_DMA flags. There is
no dependency from LAN743x hardware on memory allocation should be
in DMA_ZONE. Hence modifying the flags to use only GFP_ATOMIC. This
is consistent with other callers of lan743x_rx_init_ring_element().
Reported-by: Zhang, Liyin(CN) <Liyin.Zhang.CN@windriver.com>
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250415044509.6695-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30296ac764 ]
As discussed here:
https://lore.kernel.org/netdev/20240620090210.drop6jwh7e5qw556@skbuf/
the fact is that the xrs700x.c driver only supports offloading
HSR_PT_SLAVE_A and HSR_PT_SLAVE_B (which were the only port types at the
time the offload was written, _for this driver_).
Up until now, the API did not explicitly tell offloading drivers what
port has what role. So xrs700x can get confused and think that it can
support a configuration which it actually can't. There was a table in
the attached link which gave an example:
$ ip link add name hsr0 type hsr slave1 swp0 slave2 swp1 \
interlink swp2 supervision 45 version 1
HSR_PT_SLAVE_A HSR_PT_SLAVE_B HSR_PT_INTERLINK
----------------------------------------------------------------
user
space 0 1 2
requests
----------------------------------------------------------------
XRS700X
driver 1 2 -
understands
The switch would act as if the ring ports were swp1 and swp2.
Now that we have explicit hsr_get_port_type() API, let's use that to
work around the unintended semantical changes of the offloading API
brought by the introduction of interlink ports in HSR.
Fixes: 5055cccfc2 ("net: hsr: Provide RedBox support (HSR-SAN)")
Cc: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Link: https://patch.msgid.link/20251130131657.65080-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6c121a243 ]
Currently, if NVMEM provider is probed later than Aquantia, loading the
firmware will fail with -EINVAL.
To fix this, simply check for -EPROBE_DEFER when NVMEM is attempted and
return it.
Fixes: e93984ebc1 ("net: phy: aquantia: add firmware load support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251127114514.460924-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8048168df5 ]
The extra "count >= limit" check in stmmac_rx_zc() is redundant and
has no effect because the value of "count" doesn't change after the
while condition at this point.
However, it can change after "read_again:" label:
while (count < limit) {
...
if (count >= limit)
break;
read_again:
...
/* XSK pool expects RX frame 1:1 mapped to XSK buffer */
if (likely(status & rx_not_ls)) {
xsk_buff_free(buf->xdp);
buf->xdp = NULL;
dirty++;
count++;
goto read_again;
}
...
This patch addresses the same issue previously resolved in stmmac_rx()
by commit fa02de9e75 ("net: stmmac: fix rx budget limit check").
The fix is the same: move the check after the label to ensure that it
bounds the goto loop.
Fixes: bba2556efa ("net: stmmac: Enable RX via AF_XDP zero-copy")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251126104327.175590-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53d1548612 ]
In mt7615_mcu_wtbl_sta_add(), an skb sskb is allocated. If the
subsequent call to mt76_connac_mcu_alloc_wtbl_req() fails, the function
returns an error without freeing sskb, leading to a memory leak.
Fix this by calling dev_kfree_skb() on sskb in the error handling path
to ensure it is properly released.
Fixes: 99c457d902 ("mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251113062415.103611-1-zilin@seu.edu.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b647d2574e ]
The rtl8187_rx_cb() calculates the rx descriptor header address
by subtracting its size from the skb tail pointer.
However, it does not validate if the received packet
(skb->len from urb->actual_length) is large enough to contain this
header.
If a truncated packet is received, this will lead to a buffer
underflow, reading memory before the start of the skb data area,
and causing a kernel panic.
Add length checks for both rtl8187 and rtl8187b descriptor headers
before attempting to access them, dropping the packet cleanly if the
check fails.
Fixes: 6f7853f3cb ("rtl8187: change rtl8187_dev.c to support RTL8187B (part 2)")
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251118013258.1789949-2-eeodqql09@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bccaf1fe08 ]
Value CRSM_SFT_PD written to Software Power-Down Control Register
(CRSM_SFT_PD_CNTRL) is 0x01 and therefor different to value
CRSM_SFT_PD_RDY (0x02) read from System Status Register (CRSM_STAT) for
confirmation powerdown has been reached.
The condition could have only worked when disabling powerdown
(both 0x00), but never when enabling it (0x01 != 0x02).
Result is a timeout, like so:
$ ifdown eth0
macb f802c000.ethernet eth0: Link is Down
ADIN1100 f802c000.ethernet-ffffffff:01: adin_set_powerdown_mode failed: -110
ADIN1100 f802c000.ethernet-ffffffff:01: adin_set_powerdown_mode failed: -110
Fixes: 7eaf913299 ("net: phy: adin1100: Add initial support for ADIN1100 industrial PHY")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20251119124737.280939-2-ada@thorsis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5b9c042b ]
In rtl8180_init_rx_ring(), memory is allocated for skb packets and DMA
allocations in a loop. When an allocation fails, the previously
successful allocations are not freed on exit.
Fix that by jumping to err_free_rings label on error, which calls
rtl8180_free_rx_ring() to free the allocations. Remove the free of
rx_ring in rtl8180_init_rx_ring() error path, and set the freed
priv->rx_buf entry to null, to avoid double free.
Fixes: f653211197 ("Add rtl8180 wireless driver")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251114094527.79842-1-nihaal@cse.iitm.ac.in
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e88e86411 ]
In one of the error paths, the memory allocated for skb_rx is not freed.
Fix that by freeing it before returning.
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Link: https://patch.msgid.link/20251110175316.106591-1-nihaal@cse.iitm.ac.in
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be5febd51c ]
When the call to ath12k_wmi_arp_ns_offload() fails, the temporary memory
allocation for offload is not freed before returning. Fix that by
freeing offload in the error path.
Fixes: 1666108c74 ("wifi: ath12k: support ARP and NS offload")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251028170457.134608-1-nihaal@cse.iitm.ac.in
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea5df88aec ]
The PTP initialization is two-step. First part are the function
vsc8584_ptp_probe_once() and vsc8584_ptp_probe() at probe time which
initialize the locks, queues, creates the PTP device. The second part is
the function vsc8584_ptp_init() at config_init() time which initialize
PTP in the HW.
For VSC8574 and VSC8572, the PTP initialization is incomplete. It is
missing the first part but it makes the second part. Meaning that the
ptp_clock_register() is never called.
There is no crash without the first part when enabling PTP but this is
unexpected because some PHys have PTP functionality exposed by the
driver and some don't even though they share the same PTP clock PTP.
Fixes: 774626fa44 ("net: phy: mscc: Add PTP support for 2 more VSC PHYs")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20251023191350.190940-3-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a013ca2d4 ]
In ath11k_wmi_send_peer_assoc_cmd(), peer's transmit MCS is sent to
firmware as receive MCS while peer's receive MCS sent as transmit MCS,
which goes against firmwire's definition.
While connecting to a misbehaved AP that advertises 0xffff (meaning not
supported) for 160 MHz transmit MCS map, firmware crashes due to 0xffff
is assigned to he_mcs->rx_mcs_set field.
Ext Tag: HE Capabilities
[...]
Supported HE-MCS and NSS Set
[...]
Rx and Tx MCS Maps 160 MHz
[...]
Tx HE-MCS Map 160 MHz: 0xffff
Swap the assignment to fix this issue.
As the HE rate control mask is meant to limit our own transmit MCS, it
needs to go via he_mcs->rx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive MCS.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 61fe43e721 ("ath11k: add support for setting fixed HE rate/gi/ltf")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251017-ath11k-mcs-assignment-v1-2-da40825c1783@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47d0cd6bcc ]
While associating, firmware needs to know peer's receive capability to
calculate its own VHT transmit MCS, currently host sends this information
to firmware via mcs->rx_mcs_set field, this is wrong as firmware actually
takes it from mcs->tx_mcs_set field. Till now there is no failure seen
due to this, most likely because almost all peers are advertising the
same capability for both transmit and receive. Swap the assignment to
fix it.
Besides, rate control mask is meant to limit our own transmit MCS, hence
need to go via mcs->tx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive
capability rather than transmit capability.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251017-ath11k-mcs-assignment-v1-1-da40825c1783@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 596b911644 ]
Hardware target implements an address space larger than that PCI BAR can
map. In order to be able to access the whole target address space, the BAR
space is split into 4 segments, of which the last 3, called windows, can
be dynamically mapped to the desired area. This is achieved by updating
window register with appropriate window value. Currently each time when
accessing a register that beyond ATH11K_PCI_WINDOW_START, host calculates
the window value and caches it after window update, this way next time
when accessing a register falling in the same window, host knows that the
window is already good hence no additional update needed.
However this mechanism breaks after global reset is triggered in
ath11k_pci_soc_global_reset(), because with global reset hardware resets
window register hence the window is not properly mapped any more. Current
host does nothing about this, as a result a subsequent register access may
not work as expected if it falls in a window same as before.
Although there is no obvious issue seen now, better to fix it to avoid
future problem. The fix is done by restoring the window register after
global reset.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251014-ath11k-reset-window-cache-v1-1-b85271b111dd@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f35a07a484 ]
Currently, ath10k has a recovery check logic. It will wait for the
last recovery to finish by wait_for_completion_timeout();
But in SDIO scenarios, the recovery function may be invoked from
interrupt context, where long blocking waits are undesirable and can
lead to system instability.
Additionally, Linux’s ordered workqueue processes one task at a time.
If a previous recovery is still queued or executing, new triggers are
ignored. This prevents accurate tracking of consecutive failures and
delays transition to the WEDGED state.
To address this, move the recovery check logic into a different
workqueue.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00189
Fixes: c256a94d1b ("wifi: ath10k: shutdown driver when hardware is unreliable")
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251014110757.155-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32c3a0f889 ]
Commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath10k/bmi.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/ce.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/coredump.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htc.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htt_rx.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htt_tx.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/mac.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/trace.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-3-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Stable-dep-of: f35a07a484 ("wifi: ath10k: move recovery check logic into a new work")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc9c4252fe ]
In some scenarios, the firmware may be stopped before the interface is
removed, either due to a crash or because the remoteproc (e.g., MPSS)
is shut down early during system reboot or shutdown.
This leads to a delay during interface teardown, as the driver waits for
a vdev delete response that never arrives, eventually timing out.
Example (SNOC):
$ echo stop > /sys/class/remoteproc/remoteproc0/state
[ 71.64] remoteproc remoteproc0: stopped remote processor modem
$ reboot
[ 74.84] ath10k_snoc c800000.wifi: failed to transmit packet, dropping: -108
[ 74.84] ath10k_snoc c800000.wifi: failed to submit frame: -108
[...]
[ 82.39] ath10k_snoc c800000.wifi: Timeout in receiving vdev delete response
To avoid this, skip waiting for the vdev delete response if the firmware is
already marked as unreachable (`ATH10K_FLAG_CRASH_FLUSH`), similar to how
`ath10k_mac_wait_tx_complete()` and `ath10k_vdev_setup_sync()` handle this case.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522131704.612206-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Stable-dep-of: f35a07a484 ("wifi: ath10k: move recovery check logic into a new work")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4541b0c8c3 upstream.
Currently, RX is_mcbc bit is set for packets sent from client as
destination address (DA) is multicast/broadcast address, but packets
are actually unicast as receiver address (RA) is not multicast address.
Hence, packets are not handled properly due to this is_mcbc bit.
Therefore, reset the is_mcbc bit if interface type is AP.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411061523.859387-3-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
[ Adjust context ]
Signed-off-by: Oliver Sedlbauer <os@dev.tdt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f80e21bf6 ]
If a port interrupt setup fails after at least one port has already been
successfully initialized, the gotos miss some resource releasing:
- the already initialized PTP IRQs aren't released
- the already initialized port IRQs aren't released if the failure
occurs in ksz_pirq_setup().
Merge 'out_girq' and 'out_ptpirq' into a single 'port_release' label.
Behind this label, use the reverse loop to release all IRQ resources
for all initialized ports.
Jump in the middle of the reverse loop if an error occurs in
ksz_ptp_irq_setup() to only release the port IRQ of the current
iteration.
Cc: stable@vger.kernel.org
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-4-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ed3472173 ]
The PTP driver code only works for certain KSZ switches like KSZ9477,
KSZ9567, LAN937X and their varieties. This code is enabled by kernel
configuration CONFIG_NET_DSA_MICROCHIP_KSZ_PTP. As the DSA driver is
common to work with all KSZ switches this PTP code is not appropriate
for other unsupported switches. The ptp_capable indication is added to
the chip data structure to signal whether to execute those code.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241218020240.70601-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 0f80e21bf6 ("net: dsa: microchip: Free previously initialized ports on init failures")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0b8fec8ae ]
The IRQ numbers created through irq_create_mapping() are only assigned
to ptpmsg_irq[n].num at the end of the IRQ setup. So if an error occurs
between their creation and their assignment (for instance during the
request_threaded_irq() step), we enter the error path and fail to
release the newly created virtual IRQs because they aren't yet assigned
to ptpmsg_irq[n].num.
Move the mapping creation to ksz_ptp_msg_irq_setup() to ensure symetry
with what's released by ksz_ptp_msg_irq_free().
In the error path, move the irq_dispose_mapping to the out_ptp_msg label
so it will be called only on created IRQs.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-5-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d849ff573 ]
The commit 5cff263606 ("can: rcar_canfd: Fix controller mode setting")
has aligned with the flow mentioned in the hardware manual for all SoCs
except R-Car Gen3 and RZ/G2L SoCs. On R-Car Gen4 and RZ/G3E SoCs, due to
the wrong logic in the commit[1] sets the default mode to FD-Only mode
instead of CAN-FD mode.
This patch sets the CAN-FD mode as the default for all SoCs by dropping
the rcar_canfd_set_mode() as some SoC requires mode setting in global
reset mode, and the rest of the SoCs in channel reset mode and update the
rcar_canfd_reset_controller() to take care of these constraints. Moreover,
the RZ/G3E and R-Car Gen4 SoCs support 3 modes compared to 2 modes on the
R-Car Gen3. Use inverted logic in rcar_canfd_reset_controller() to
simplify the code later to support FD-only mode.
[1]
commit 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Fixes: 5cff263606 ("can: rcar_canfd: Fix controller mode setting")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20251118123926.193445-1-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[ adapted to use existing is_gen4() helper and RCANFD_GEN4_FDCFG() macro instead of new ch_interface_mode field and fcbase struct ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25b62cc5b2 upstream.
If something goes wrong at setup, ksz_irq_free() can be called on
uninitialized ksz_irq (for example when ksz_ptp_irq_setup() fails). It
leads to freeing uninitialized IRQ numbers and/or domains.
Use dsa_switch_for_each_user_port_continue_reverse() in the error path
to iterate only over the fully initialized ports.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-3-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e059305be upstream.
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, during the PTP IRQ setup,
we verify that its returned value isn't negative.
Fix the irq_find_mapping() check to enter the error path when 0 is
returned. Return -EINVAL in such case.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b2 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-2-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b3c09e166 upstream.
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, on each
irq_find_mapping() call, we verify that the returned value isn't
negative.
Fix the irq_find_mapping() checks to enter error paths when 0 is
returned. Return -EINVAL in such cases.
CC: stable@vger.kernel.org
Fixes: c9cd961c0d ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-1-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76544beea7 upstream.
Reading the interrupt register `SUN4I_REG_INT_ADDR` causes all of its bits
to be reset. If we ever reach the condition of handling more than
`SUN4I_CAN_MAX_IRQ` IRQs, we will have read the register and reset all its
bits but without actually handling the interrupt inside of the loop body.
This may, among other issues, cause us to never `netif_wake_queue()` again
after a transmission interrupt.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Cc: stable@vger.kernel.org
Co-developed-by: Thomas Mühlbacher <tmuehlbacher@posteo.net>
Signed-off-by: Thomas Mühlbacher <tmuehlbacher@posteo.net>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251116-sun4i-fix-loop-v1-1-3d76d3f81950@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30db4451c7 upstream.
Reading the interrupt register `SJA1000_IR` causes all of its bits to be
reset. If we ever reach the condition of handling more than
`SJA1000_MAX_IRQ` IRQs, we will have read the register and reset all its
bits but without actually handling the interrupt inside of the loop
body.
This may, among other issues, cause us to never `netif_wake_queue()`
again after a transmission interrupt.
Fixes: 429da1cc84 ("can: Driver for the SJA1000 CAN controller")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Mühlbacher <tmuehlbacher@posteo.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20251115153437.11419-1-tmuehlbacher@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a060d0fac ]
There are currently two situations that can trigger the PTP interrupt,
one is the PPS event, the other is the PEROUT event. However, the irq
handler fec_pps_interrupt() does not check the irq event type and
directly registers a PPS event into the system, but the event may be
a PEROUT event. This is incorrect because PEROUT is an output signal,
while PPS is the input of the kernel PPS system. Therefore, add a check
for the event type, if pps_enable is true, it means that the current
event is a PPS event, and then the PPS event is registered.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-5-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0a1f3d7e1 ]
In the current driver, PPS and PEROUT use the same channel to generate
the events, so they cannot be enabled at the same time. Otherwise, the
later configuration will overwrite the earlier configuration. Therefore,
when configuring PPS, the driver will check whether PEROUT is enabled.
Similarly, when configuring PEROUT, the driver will check whether PPS
is enabled.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-4-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e97faa0c20 ]
If the previously set PEROUT is already active, updating it will cause
the new PEROUT to start immediately instead of at the specified time.
This is because fep->reload_period is updated whithout check whether
the PEROUT is enabled, and the old PEROUT is not disabled. Therefore,
the pulse period will be updated immediately in the pulse interrupt
handler fec_pps_interrupt().
Currently, the driver does not support directly updating PEROUT and it
will make the logic be more complicated. To fix the current issue, add
a check before enabling the PEROUT, the driver will return an error if
PEROUT is enabled. If users wants to update a new PEROUT, they should
disable the old PEROUT first.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50caa74468 ]
The PEROUT allows the user to set a specified future time to output the
periodic signal. If the future time is far from the current time, the FEC
driver will use hrtimer to configure PEROUT one second before the future
time. However, the hrtimer will not be canceled if the PEROUT is disabled
before the hrtimer expires. So the PEROUT will be configured when the
hrtimer expires, which is not as expected. Therefore, cancel the hrtimer
in fec_ptp_pps_disable() to fix this issue.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ffcb7b890 ]
The atlantic driver can receive packets with more than MAX_SKB_FRAGS (17)
fragments when handling large multi-descriptor packets. This causes an
out-of-bounds write in skb_add_rx_frag_netmem() leading to kernel panic.
The issue occurs because the driver doesn't check the total number of
fragments before calling skb_add_rx_frag(). When a packet requires more
than MAX_SKB_FRAGS fragments, the fragment index exceeds the array bounds.
Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE,
then all fragments are accounted for. And reusing the existing check to
prevent the overflow earlier in the code path.
This crash occurred in production with an Aquantia AQC113 10G NIC.
Stack trace from production environment:
```
RIP: 0010:skb_add_rx_frag_netmem+0x29/0xd0
Code: 90 f3 0f 1e fa 0f 1f 44 00 00 48 89 f8 41 89
ca 48 89 d7 48 63 ce 8b 90 c0 00 00 00 48 c1 e1 04 48 01 ca 48 03 90
c8 00 00 00 <48> 89 7a 30 44 89 52 3c 44 89 42 38 40 f6 c7 01 75 74 48
89 fa 83
RSP: 0018:ffffa9bec02a8d50 EFLAGS: 00010287
RAX: ffff925b22e80a00 RBX: ffff925ad38d2700 RCX:
fffffffe0a0c8000
RDX: ffff9258ea95bac0 RSI: ffff925ae0a0c800 RDI:
0000000000037a40
RBP: 0000000000000024 R08: 0000000000000000 R09:
0000000000000021
R10: 0000000000000848 R11: 0000000000000000 R12:
ffffa9bec02a8e24
R13: ffff925ad8615570 R14: 0000000000000000 R15:
ffff925b22e80a00
FS: 0000000000000000(0000)
GS:ffff925e47880000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9258ea95baf0 CR3: 0000000166022004 CR4:
0000000000f72ef0
PKRU: 55555554
Call Trace:
<IRQ>
aq_ring_rx_clean+0x175/0xe60 [atlantic]
? aq_ring_rx_clean+0x14d/0xe60 [atlantic]
? aq_ring_tx_clean+0xdf/0x190 [atlantic]
? kmem_cache_free+0x348/0x450
? aq_vec_poll+0x81/0x1d0 [atlantic]
? __napi_poll+0x28/0x1c0
? net_rx_action+0x337/0x420
```
Fixes: 6aecbba12b ("net: atlantic: add check for MAX_SKB_FRAGS")
Changes in v4:
- Add Fixes: tag to satisfy patch validation requirements.
Changes in v3:
- Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE,
then all fragments are accounted for.
Signed-off-by: Jiefeng Zhang <jiefeng.z.zhang@gmail.com>
Link: https://patch.msgid.link/20251126032249.69358-1-jiefeng.z.zhang@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d66e093e0 ]
Fix a potential counter roll-over issue in fbnic_mbx_alloc_rx_msgs()
when calculating descriptor slots. The issue occurs when head - tail
results in a large positive value (unsigned) and the compiler interprets
head - tail - 1 as a signed value.
Since FBNIC_IPC_MBX_DESC_LEN is a power of two, use a masking operation,
which is a common way of avoiding this problem when dealing with these
sort of ring space calculations.
Fixes: da3cde0820 ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20251125211704.3222413-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da62abaaa2 ]
When using the SGMII PCS as a fixed-link chip-to-chip connection, it is
easy to miss the fact that traffic passes only at 1G, since that's what
any normal such connection would use.
When using the SGMII PCS connected towards an on-board PHY or an SFP
module, it is immediately noticeable that when the link resolves to a
speed other than 1G, traffic from the MAC fails to pass: TX counters
increase, but nothing gets decoded by the other end, and no local RX
counters increase either.
Artificially lowering a fixed-link rate to speed = <100> makes us able
to see the same issue as in the case of having an SGMII PHY.
Some debugging shows that the XPCS configuration is A-OK, but that the
MAC Configuration Table entry for the port has the SPEED bits still set
to 1000Mbps, due to a special condition in the driver. Deleting that
condition, and letting the resolved link speed be programmed directly
into the MAC speed field, results in a functional link at all 3 speeds.
This piece of evidence, based on testing on both generations with SGMII
support (SJA1105S and SJA1110A) directly contradicts the statement from
the blamed commit that "the MAC is fixed at 1 Gbps and we need to
configure the PCS only (if even that)". Worse, that statement is not
backed by any documentation, and no one from NXP knows what it might
refer to.
I am unable to recall sufficient context regarding my testing from March
2020 to understand what led me to draw such a braindead and factually
incorrect conclusion. Yet, there is nothing of value regarding forcing
the MAC speed, either for SGMII or 2500Base-X (introduced at a later
stage), so remove all such logic.
Fixes: ffe10e679c ("net: dsa: sja1105: Add support for the SGMII port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251122111324.136761-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a18891b557 ]
The static configuration reload saves the port speed in the static
configuration tables by first converting it from the internal
respresentation to the SPEED_xxx ethtool representation, and then
converts it back to restore the setting. This is because
sja1105_adjust_port_config() takes the speed as SPEED_xxx.
However, this is unnecessarily complex. If we split
sja1105_adjust_port_config() up, we can simply save and restore the
mac[port].speed member in the static configuration tables.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMa-005ZIX-If@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: da62abaaa2 ("net: dsa: sja1105: fix SGMII linking at 10M or 100M but not passing traffic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fcb8ab4a0 ]
Correct it since M.2 device T99W640 has updated from T99W515.
We need to align it with MHI side otherwise this modem can't
get the network.
Fixes: ae5a342643 ("bus: mhi: host: pci_generic: Fix the modem name of Foxconn T99W640")
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20251125070900.33324-1-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5bce28f6b ]
Currently, when skb is null, the driver prints an error and then
dereferences skb on the next line.
To fix this, let's add a 'break' after the error message to switch
to sxgbe_rx_refill(), which is similar to the approach taken by the
other drivers in this particular case, e.g. calxeda with xgmac_rx().
Found during a code review.
Fixes: 1edb9ca69e ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121123834.97748-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ae9cfc454 ]
Attempting to add a port device that is already up will expectedly fail,
but not before modifying the team device header_ops.
In the case of the syzbot reproducer the gre0 device is
already in state UP when it attempts to add it as a
port device of team0, this fails but before that
header_ops->create of team0 is changed from eth_header to ipgre_header
in the call to team_dev_type_check_change.
Later when we end up in ipgre_header() struct ip_tunnel* points to nonsense
as the private data of the device still holds a struct team.
Example sequence of iproute2 commands to reproduce the hang/BUG():
ip link add dev team0 type team
ip link add dev gre0 type gre
ip link set dev gre0 up
ip link set dev gre0 master team0
ip link set dev team0 up
ping -I team0 1.1.1.1
Move team_dev_type_check_change down where all other checks have passed
as it changes the dev type with no way to restore it in case
one of the checks that follow it fail.
Also make sure to preserve the origial mtu assignment:
- If port_dev is not the same type as dev, dev takes mtu from port_dev
- If port_dev is the same type as dev, port_dev takes mtu from dev
This is done by adding a conditional before the call to dev_set_mtu
to prevent it from assigning port_dev->mtu = dev->mtu and instead
letting team_dev_type_check_change assign dev->mtu = port_dev->mtu.
The conditional is needed because the patch moves the call to
team_dev_type_check_change past dev_set_mtu.
Testing:
- team device driver in-tree selftests
- Add/remove various devices as slaves of team device
- syzbot
Reported-by: syzbot+a2a3b519de727b0f7903@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a2a3b519de727b0f7903
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Signed-off-by: Nikola Z. Ivanov <zlatistiv@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20251122002027.695151-1-zlatistiv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2099d9f16 ]
The rate limiting validation condition currently checks the output
variable max_bw_value[i] instead of the input value
maxrate->tc_maxrate[i]. This causes the validation to compare an
uninitialized or stale value rather than the actual requested rate.
The condition should check the input rate to properly validate against
the upper limit:
} else if (maxrate->tc_maxrate[i] <= upper_limit_gbps) {
This aligns with the pattern used in the first branch, which correctly
checks maxrate->tc_maxrate[i] against upper_limit_mbps.
The current implementation can lead to unreliable validation behavior:
- For rates between 25.5 Gbps and 255 Gbps, if max_bw_value[i] is 0
from initialization, the GBPS path may be taken regardless of whether
the actual rate is within bounds
- When processing multiple TCs (i > 0), max_bw_value[i] contains the
value computed for the previous TC, affecting the validation logic
- The overflow check for rates exceeding 255 Gbps may not trigger
consistently depending on previous array values
This patch ensures the validation correctly examines the requested rate
value for proper bounds checking.
Fixes: 43b27d1bd8 ("net/mlx5e: Fix wraparound in rate limiting for values above 255 Gbps")
Signed-off-by: Danielle Costantino <dcostantino@meta.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20251124180043.2314428-1-dcostantino@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9780f535f8 ]
To initialize the taprio block in lan966x, it is required to configure
the register REVISIT_DLY. The purpose of this register is to set the
delay before revisit the next gate and the value of this register depends
on the system clock. The problem is that the we calculated wrong the value
of the system clock period in picoseconds. The actual system clock is
~165.617754MHZ and this correspond to a period of 6038 pico seconds and
not 15125 as currently set.
Fixes: e462b27173 ("net: lan966x: Add offload support for taprio")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121061411.810571-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec3803b591 ]
As the interface mode doesn't need to be updated on PHYs connected with
USXGMII and integrated PHYs, gpy_update_interface() should just return 0
in these cases rather than -EINVAL which has wrongly been introduced by
commit 7a495dde27 ("net: phy: mxl-gpy: Change gpy_update_interface()
function return type"), as this breaks support for those PHYs.
Fixes: 7a495dde27 ("net: phy: mxl-gpy: Change gpy_update_interface() function return type")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/f744f721a1fcc5e2e936428c62ff2c7d94d2a293.1763648168.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a14602fcae ]
As explain in commit fa349e396e ("veth: Fix race with AF_XDP exposing
old or uninitialized descriptors") for veth there is a chance after
napi_complete_done() that another CPU can manage start another NAPI
instance running veth_pool(). For NAPI this is correctly handled as the
napi_schedule_prep() check will prevent multiple instances from getting
scheduled, but for the remaining code in veth_pool() this can run
concurrent with the newly started NAPI instance.
The problem/race is that xdp_clear_return_frame_no_direct() isn't
designed to be nested.
Prior to commit 401cb7dae8 ("net: Reference bpf_redirect_info via
task_struct on PREEMPT_RT.") the temporary BPF net context
bpf_redirect_info was stored per CPU, where this wasn't an issue. Since
this commit the BPF context is stored in 'current' task_struct. When
running veth in threaded-NAPI mode, then the kthread becomes the storage
area. Now a race exists between two concurrent veth_pool() function calls
one exiting NAPI and one running new NAPI, both using the same BPF net
context.
Race is when another CPU gets within the xdp_set_return_frame_no_direct()
section before exiting veth_pool() calls the clear-function
xdp_clear_return_frame_no_direct().
Fixes: 401cb7dae8 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/176356963888.337072.4805242001928705046.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5442a9da69 ]
Commit dc82a33297 ("veth: apply qdisc backpressure on full ptr_ring to
reduce TX drops") introduced a race condition that can lead to a permanently
stalled TXQ. This was observed in production on ARM64 systems (Ampere Altra
Max).
The race occurs in veth_xmit(). The producer observes a full ptr_ring and
stops the queue (netif_tx_stop_queue()). The subsequent conditional logic,
intended to re-wake the queue if the consumer had just emptied it (if
(__ptr_ring_empty(...)) netif_tx_wake_queue()), can fail. This leads to a
"lost wakeup" where the TXQ remains stopped (QUEUE_STATE_DRV_XOFF) and
traffic halts.
This failure is caused by an incorrect use of the __ptr_ring_empty() API
from the producer side. As noted in kernel comments, this check is not
guaranteed to be correct if a consumer is operating on another CPU. The
empty test is based on ptr_ring->consumer_head, making it reliable only for
the consumer. Using this check from the producer side is fundamentally racy.
This patch fixes the race by adopting the more robust logic from an earlier
version V4 of the patchset, which always flushed the peer:
(1) In veth_xmit(), the racy conditional wake-up logic and its memory barrier
are removed. Instead, after stopping the queue, we unconditionally call
__veth_xdp_flush(rq). This guarantees that the NAPI consumer is scheduled,
making it solely responsible for re-waking the TXQ.
This handles the race where veth_poll() consumes all packets and completes
NAPI *before* veth_xmit() on the producer side has called netif_tx_stop_queue.
The __veth_xdp_flush(rq) will observe rx_notify_masked is false and schedule
NAPI.
(2) On the consumer side, the logic for waking the peer TXQ is moved out of
veth_xdp_rcv() and placed at the end of the veth_poll() function. This
placement is part of fixing the race, as the netif_tx_queue_stopped() check
must occur after rx_notify_masked is potentially set to false during NAPI
completion.
This handles the race where veth_poll() consumes all packets, but haven't
finished (rx_notify_masked is still true). The producer veth_xmit() stops the
TXQ and __veth_xdp_flush(rq) will observe rx_notify_masked is true, meaning
not starting NAPI. Then veth_poll() change rx_notify_masked to false and
stops NAPI. Before exiting veth_poll() will observe TXQ is stopped and wake
it up.
Fixes: dc82a33297 ("veth: apply qdisc backpressure on full ptr_ring to reduce TX drops")
Reviewed-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/176295323282.307447.14790015927673763094.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a14602fcae ("veth: reduce XDP no_direct return section to fix race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc82a33297 ]
In production, we're seeing TX drops on veth devices when the ptr_ring
fills up. This can occur when NAPI mode is enabled, though it's
relatively rare. However, with threaded NAPI - which we use in
production - the drops become significantly more frequent.
The underlying issue is that with threaded NAPI, the consumer often runs
on a different CPU than the producer. This increases the likelihood of
the ring filling up before the consumer gets scheduled, especially under
load, leading to drops in veth_xmit() (ndo_start_xmit()).
This patch introduces backpressure by returning NETDEV_TX_BUSY when the
ring is full, signaling the qdisc layer to requeue the packet. The txq
(netdev queue) is stopped in this condition and restarted once
veth_poll() drains entries from the ring, ensuring coordination between
NAPI and qdisc.
Backpressure is only enabled when a qdisc is attached. Without a qdisc,
the driver retains its original behavior - dropping packets immediately
when the ring is full. This avoids unexpected behavior changes in setups
without a configured qdisc.
With a qdisc in place (e.g. fq, sfq) this allows Active Queue Management
(AQM) to fairly schedule packets across flows and reduce collateral
damage from elephant flows.
A known limitation of this approach is that the full ring sits in front
of the qdisc layer, effectively forming a FIFO buffer that introduces
base latency. While AQM still improves fairness and mitigates flow
dominance, the latency impact is measurable.
In hardware drivers, this issue is typically addressed using BQL (Byte
Queue Limits), which tracks in-flight bytes needed based on physical link
rate. However, for virtual drivers like veth, there is no fixed bandwidth
constraint - the bottleneck is CPU availability and the scheduler's ability
to run the NAPI thread. It is unclear how effective BQL would be in this
context.
This patch serves as a first step toward addressing TX drops. Future work
may explore adapting a BQL-like mechanism to better suit virtual devices
like veth.
Reported-by: Yan Zhai <yan@cloudflare.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Link: https://patch.msgid.link/174559294022.827981.1282809941662942189.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a14602fcae ("veth: reduce XDP no_direct return section to fix race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34dd0fecaa ]
The "noqueue" qdisc can either be directly attached, or get default
attached if net_device priv_flags has IFF_NO_QUEUE. In both cases, the
allocated Qdisc structure gets it's enqueue function pointer reset to
NULL by noqueue_init() via noqueue_qdisc_ops.
This is a common case for software virtual net_devices. For these devices
with no-queue, the transmission path in __dev_queue_xmit() will bypass
the qdisc layer. Directly invoking device drivers ndo_start_xmit (via
dev_hard_start_xmit). In this mode the device driver is not allowed to
ask for packets to be queued (either via returning NETDEV_TX_BUSY or
stopping the TXQ).
The simplest and most reliable way to identify this no-queue case is by
checking if enqueue == NULL.
The vrf driver currently open-codes this check (!qdisc->enqueue). While
functionally correct, this low-level detail is better encapsulated in a
dedicated helper for clarity and long-term maintainability.
To make this behavior more explicit and reusable, this patch introduce a
new helper: qdisc_txq_has_no_queue(). Helper will also be used by the
veth driver in the next patch, which introduces optional qdisc-based
backpressure.
This is a non-functional change.
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/174559293172.827981.7583862632045264175.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a14602fcae ("veth: reduce XDP no_direct return section to fix race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 395d988f93 ]
The URB received in gs_usb_receive_bulk_callback() contains a struct
gs_host_frame. The length of the data after the header depends on the
gs_host_frame hf::flags and the active device features (e.g. time
stamping).
Introduce a new function gs_usb_get_minimum_length() and check that we have
at least received the required amount of data before accessing it. Only
copy the data to that skb that has actually been received.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://patch.msgid.link/20251114-gs_usb-fix-usb-callbacks-v1-3-a29b42eacada@pengutronix.de
[mkl: rename gs_usb_get_minimum_length() -> +gs_usb_get_minimum_rx_length()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
