commit c4cdf73762 upstream.
The local variable 'val' was never clamped to -75000 or 180000 because
the return value of clamp_val() was not used. Fix this by assigning the
clamped value back to 'val', and use clamp() instead of clamp_val().
Cc: stable@vger.kernel.org
Fixes: a557a92e68 ("net: phy: marvell-88q2xxx: add support for temperature sensor")
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251202172743.453055-3-thorsten.blum@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6c121a243 ]
Currently, if NVMEM provider is probed later than Aquantia, loading the
firmware will fail with -EINVAL.
To fix this, simply check for -EPROBE_DEFER when NVMEM is attempted and
return it.
Fixes: e93984ebc1 ("net: phy: aquantia: add firmware load support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251127114514.460924-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bccaf1fe08 ]
Value CRSM_SFT_PD written to Software Power-Down Control Register
(CRSM_SFT_PD_CNTRL) is 0x01 and therefor different to value
CRSM_SFT_PD_RDY (0x02) read from System Status Register (CRSM_STAT) for
confirmation powerdown has been reached.
The condition could have only worked when disabling powerdown
(both 0x00), but never when enabling it (0x01 != 0x02).
Result is a timeout, like so:
$ ifdown eth0
macb f802c000.ethernet eth0: Link is Down
ADIN1100 f802c000.ethernet-ffffffff:01: adin_set_powerdown_mode failed: -110
ADIN1100 f802c000.ethernet-ffffffff:01: adin_set_powerdown_mode failed: -110
Fixes: 7eaf913299 ("net: phy: adin1100: Add initial support for ADIN1100 industrial PHY")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20251119124737.280939-2-ada@thorsis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea5df88aec ]
The PTP initialization is two-step. First part are the function
vsc8584_ptp_probe_once() and vsc8584_ptp_probe() at probe time which
initialize the locks, queues, creates the PTP device. The second part is
the function vsc8584_ptp_init() at config_init() time which initialize
PTP in the HW.
For VSC8574 and VSC8572, the PTP initialization is incomplete. It is
missing the first part but it makes the second part. Meaning that the
ptp_clock_register() is never called.
There is no crash without the first part when enabling PTP but this is
unexpected because some PHys have PTP functionality exposed by the
driver and some don't even though they share the same PTP clock PTP.
Fixes: 774626fa44 ("net: phy: mscc: Add PTP support for 2 more VSC PHYs")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20251023191350.190940-3-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec3803b591 ]
As the interface mode doesn't need to be updated on PHYs connected with
USXGMII and integrated PHYs, gpy_update_interface() should just return 0
in these cases rather than -EINVAL which has wrongly been introduced by
commit 7a495dde27 ("net: phy: mxl-gpy: Change gpy_update_interface()
function return type"), as this breaks support for those PHYs.
Fixes: 7a495dde27 ("net: phy: mxl-gpy: Change gpy_update_interface() function return type")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/f744f721a1fcc5e2e936428c62ff2c7d94d2a293.1763648168.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bf91f4bc9c upstream.
The blamed commit introduced the function lanphy_modify_page_reg which
as name suggests it, it modifies the registers. In the same commit we
have started to use this function inside the drivers. The problem is
that in the function lan8814_config_init we passed the wrong page number
when disabling the aneg towards host side. We passed extended page number
4(LAN8814_PAGE_COMMON_REGS) instead of extended page
5(LAN8814_PAGE_PORT_REGS)
Fixes: a0de636ed7 ("net: phy: micrel: Introduce lanphy_modify_page_reg")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250925064702.3906950-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 96a9178a29 ]
The lan8814 is a quad-phy and it is using QSGMII towards the MAC.
The problem is that everytime when one of the ports is configured then
the PCS is reseted for all the PHYs. Meaning that the other ports can
loose traffic until the link is establish again.
To fix this, do the reset one time for the entire PHY package.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Divya Koppera <Divya.Koppera@microchip.com >
Link: https://patch.msgid.link/20251106090637.2030625-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d471793a9b ]
The functions lan_*_page_reg gets as a second parameter the page
where the register is. In all the functions the page was hardcoded.
Replace the hardcoded values with defines to make it more clear
what are those parameters.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250818075121.1298170-4-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 96a9178a29 ("net: phy: micrel: lan8814 fix reset of the QSGMII interface")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0de636ed7 ]
As the name suggests this function modifies the register in an
extended page. It has the same parameters as phy_modify_mmd.
This function was introduce because there are many places in the
code where the registers was read then the value was modified and
written back. So replace all this code with this function to make
it clear.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250818075121.1298170-3-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 96a9178a29 ("net: phy: micrel: lan8814 fix reset of the QSGMII interface")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60f887b129 ]
When a PHY is halted (e.g. `ip link set dev lan2 down`), several
fields in struct phy_device may still reflect the last active
connection. This leads to ethtool showing stale values even though
the link is down.
Reset selected fields in _phy_state_machine() when transitioning
to PHY_HALTED and the link was previously up:
- speed/duplex -> UNKNOWN, but only in autoneg mode (in forced mode
these fields carry configuration, not status)
- master_slave_state -> UNKNOWN if previously supported
- mdix -> INVALID (state only, same meaning as "unknown")
- lp_advertising -> always cleared
The cleanup is skipped if the PHY is in PHY_ERROR state, so the
last values remain available for diagnostics.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250917094751.2101285-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deb105f498 ]
The 88e1510 PHY has an erratum where the phy downshift counter is not
cleared after phy being suspended(BMCR_PDOWN set) and then later
resumed(BMCR_PDOWN cleared). This can cause the gigabit link to
intermittently downshift to a lower speed.
Disabling and re-enabling the downshift feature clears the counter,
allowing the PHY to retry gigabit link negotiation up to the programmed
retry count times before downshifting. This behavior has been observed
on copper links.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250906-marvell_fix-v2-1-f6efb286937f@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0f849c1cc ]
fixed_phy_register() creates and registers the phy_device. To be
symmetric, we should not only unregister, but also free the phy_device
in fixed_phy_unregister(). This allows to simplify code in users.
Note wrt of_phy_deregister_fixed_link():
put_device(&phydev->mdio.dev) and phy_device_free(phydev) are identical.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/ad8dda9a-10ed-4060-916b-3f13bdbb899d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 399d109347 ]
Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception.
Fixes: b3f1a08fcf ("net: phy: micrel: Add support for PTP_PF_EXTTS for lan8814")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20251021132034.983936-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddbf0e78a8 ]
Add quirk for a copper SFP that identifies itself as "FLYPRO"
"SFP-10GT-CS-30M". It uses RollBall protocol to talk to the PHY.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250831105910.3174-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8ea25274eb upstream.
reset_gpio is claimed in mdiobus_register_device(), but it is not
released in mdiobus_unregister_device(). It is instead only
released when the whole MDIO bus is unregistered.
When a device uses the reset_gpio property, it becomes impossible
to unregister it and register it again, because the GPIO remains
claimed.
This patch resolves that issue.
Fixes: bafbdd527d ("phylib: Add device reset GPIO support") # see notes
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: Csókás Bence <csokas.bence@prolan.hu>
[ csokas.bence: Resolve rebase conflict and clarify msg ]
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Link: https://patch.msgid.link/20250807135449.254254-2-csokas.bence@prolan.hu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
[ csokas.bence: Use the v1 patch on top of 6.12, as specified in notes ]
Signed-off-by: Bence Csókás <csokas.bence@prolan.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b2bfdbf43 ]
When transmitting a PTP frame which is timestamp using 2 step, the
following warning appears if CONFIG_PROVE_LOCKING is enabled:
=============================
[ BUG: Invalid wait context ]
6.17.0-rc1-00326-ge6160462704e #427 Not tainted
-----------------------------
ptp4l/119 is trying to lock:
c2a44ed4 (&vsc8531->ts_lock){+.+.}-{3:3}, at: vsc85xx_txtstamp+0x50/0xac
other info that might help us debug this:
context-{4:4}
4 locks held by ptp4l/119:
#0: c145f068 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x58/0x1440
#1: c29df974 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: __dev_queue_xmit+0x5c4/0x1440
#2: c2aaaad0 (_xmit_ETHER#2){+.-.}-{2:2}, at: sch_direct_xmit+0x108/0x350
#3: c2aac170 (&lan966x->tx_lock){+.-.}-{2:2}, at: lan966x_port_xmit+0xd0/0x350
stack backtrace:
CPU: 0 UID: 0 PID: 119 Comm: ptp4l Not tainted 6.17.0-rc1-00326-ge6160462704e #427 NONE
Hardware name: Generic DT based system
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x7c/0xac
dump_stack_lvl from __lock_acquire+0x8e8/0x29dc
__lock_acquire from lock_acquire+0x108/0x38c
lock_acquire from __mutex_lock+0xb0/0xe78
__mutex_lock from mutex_lock_nested+0x1c/0x24
mutex_lock_nested from vsc85xx_txtstamp+0x50/0xac
vsc85xx_txtstamp from lan966x_fdma_xmit+0xd8/0x3a8
lan966x_fdma_xmit from lan966x_port_xmit+0x1bc/0x350
lan966x_port_xmit from dev_hard_start_xmit+0xc8/0x2c0
dev_hard_start_xmit from sch_direct_xmit+0x8c/0x350
sch_direct_xmit from __dev_queue_xmit+0x680/0x1440
__dev_queue_xmit from packet_sendmsg+0xfa4/0x1568
packet_sendmsg from __sys_sendto+0x110/0x19c
__sys_sendto from sys_send+0x18/0x20
sys_send from ret_fast_syscall+0x0/0x1c
Exception stack(0xf0b05fa8 to 0xf0b05ff0)
5fa0: 00000001 0000000e0000000e 0004b47a 0000003a 00000000
5fc0: 00000001 0000000e 00000000 00000121 0004af58 00044874 00000000 00000000
5fe0: 00000001 bee9d420 00025a10 b6e75c7c
So, instead of using the ts_lock for tx_queue, use the spinlock that
skb_buff_head has.
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250902121259.3257536-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 882e57cbc7 ]
It looks like that every time when the interface was set down and up the
driver was creating a new ptp clock. On top of this the function
ptp_clock_unregister was never called.
Therefore fix this by calling ptp_clock_register and initialize the
mii_ts struct inside the probe function and call ptp_clock_unregister when
driver is removed.
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250825065543.2916334-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc1a59cff9 ]
There was a problem when we received frames and the frames were
timestamped. The driver is configured to store the nanosecond part of
the timestmap in the ptp reserved bits and it would take the second part
by reading the LTC. The problem is that when reading the LTC we are in
atomic context and to read the second part will go over mdio bus which
might sleep, so we get an error.
The fix consists in actually put all the frames in a queue and start the
aux work and in that work to read the LTC and then calculate the full
received time.
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250818081029.1300780-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57ec5a8735 ]
According to the LAN8710A datasheet (Rev. B, section 3.8.5.1), a hardware
reset is required after power-on, and the reference clock (REF_CLK) must be
established before asserting reset.
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Cc: Csókás Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250728152916.46249-2-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3117a11fff ]
Reset the bit 12 in PHY's LRE Control register upon initialization.
According to the datasheet, this bit must be written to zero after
every device reset.
Signed-off-by: Kamil Horák - 2N <kamilh@axis.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250708090140.61355-5-kamilh@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f25a7eaa89 ]
The Renesas RZ/G3E SMARC EVK uses KSZ9131RNXC phy. On deep power state,
PHY loses the power and on wakeup the rgmii delays are not reconfigured
causing it to fail.
Replace the callback kszphy_resume()->ksz9131_resume() for reconfiguring
the rgmii_delay when it exits from PM suspend state.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250711054029.48536-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 49db61c27c upstream.
Commit 21b688dabe ("net: phy: micrel: Cable Diag feature for lan8814
phy") introduced cable_test support for the LAN8814 that reuses parts of
the KSZ886x logic and introduced the cable_diag_reg and pair_mask
parameters to account for differences between those chips.
However, it did not update the ksz8081_type struct, so those members are
now 0, causing no pairs to be tested in ksz886x_cable_test_get_status
and ksz886x_cable_test_wait_for_completion to poll the wrong register
for the affected PHYs (Basic Control/Reset, which is 0 in normal
operation) and exit immediately.
Fix this by setting both struct members accordingly.
Fixes: 21b688dabe ("net: phy: micrel: Cable Diag feature for lan8814 phy")
Cc: stable@vger.kernel.org
Signed-off-by: Florian Larysch <fl@n621.de>
Link: https://patch.msgid.link/20250723222250.13960-1-fl@n621.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6fb5ff63b3 ]
According to the 1588 standard, it is possible to use both unicast and
multicast frames to send the PTP information. It was noticed that if the
frames were unicast they were not processed by the analyzer meaning that
they were not timestamped. Therefore fix this to match also these
unicast frames.
Fixes: ab2bf93393 ("net: phy: mscc: 1588 block initialization")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250726140307.3039694-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0f2b992d8 ]
If a PHY has no driver, the genphy driver is probed/removed directly in
phy_attach/detach. If the PHY's ofnode has an "leds" subnode, then the
LEDs will be (un)registered when probing/removing the genphy driver.
This could occur if the leds are for a non-generic driver that isn't
loaded for whatever reason. Synchronously removing the PHY device in
phy_detach leads to the following deadlock:
rtnl_lock()
ndo_close()
...
phy_detach()
phy_remove()
phy_leds_unregister()
led_classdev_unregister()
led_trigger_set()
netdev_trigger_deactivate()
unregister_netdevice_notifier()
rtnl_lock()
There is a corresponding deadlock on the open/register side of things
(and that one is reported by lockdep), but it requires a race while this
one is deterministic.
Generic PHYs do not support LEDs anyway, so don't bother registering
them.
Fixes: 01e5b728e9 ("net: phy: Add a binding for PHY LEDs")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250707195803.666097-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd4360c0e8 ]
Restrict the 100Mbit forced-mode workaround to link-down transitions
only, to prevent repeated link reset cycles in certain configurations.
The workaround was originally introduced to improve signal reliability
when switching cables between long and short distances. It temporarily
forces the PHY into 10 Mbps before returning to 100 Mbps.
However, when used with autonegotiating link partners (e.g., Intel i350),
executing this workaround on every link change can confuse the partner
and cause constant renegotiation loops. This results in repeated link
down/up transitions and the PHY never reaching a stable state.
Limit the workaround to only run during the PHY_NOLINK state. This ensures
it is triggered only once per link drop, avoiding disruptive toggling
while still preserving its intended effect.
Note: I am not able to reproduce the original issue that this workaround
addresses. I can only confirm that 100 Mbit mode works correctly in my
test setup. Based on code inspection, I assume the workaround aims to
reset some internal state machine or signal block by toggling speeds.
However, a PHY reset is already performed earlier in the function via
phy_init_hw(), which may achieve a similar effect. Without a reproducer,
I conservatively keep the workaround but restrict its conditions.
Fixes: e57cf3639c ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250709130753.3994461-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4517c363e ]
Enable .soft_reset for the LAN88xx PHY driver by assigning
genphy_soft_reset() to ensure that the phylib core performs a proper
soft reset during reconfiguration.
Previously, the driver left .soft_reset unimplemented, so calls to
phy_init_hw() (e.g., from lan88xx_link_change_notify()) did not fully
reset the PHY. As a result, stale contents in the Link Partner Ability
(LPA) register could persist, causing the PHY to incorrectly report
that the link partner advertised autonegotiation even when it did not.
Using genphy_soft_reset() guarantees a clean reset of the PHY and
corrects the false autoneg reporting in these scenarios.
Fixes: ccb989e4d1 ("net: phy: microchip: Reset LAN88xx PHY to ensure clean link state on LAN7800/7850")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250709130753.3994461-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dfe110cc0 ]
Force a fixed MDI-X mode when auto-negotiation is disabled to prevent
link instability.
When forcing the link speed and duplex on a LAN9500 PHY (e.g., with
`ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto
mode, the PHY fails to establish a stable link. This occurs because the
PHY's Auto-MDIX algorithm is not designed to operate when
auto-negotiation is disabled. In this state, the PHY continuously
toggles the TX/RX signal pairs, which prevents the link partner from
synchronizing.
This patch resolves the issue by detecting when auto-negotiation is
disabled. If the MDI-X control mode is set to 'auto', the driver now
forces a specific, stable mode (ETH_TP_MDI) to prevent the pair
toggling. This choice of a fixed MDI mode mirrors the behavior the
hardware would exhibit if the AUTOMDIX_EN strap were configured for a
fixed MDI connection.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0713e55533 ]
Override the hardware strap configuration for MDI-X mode to ensure a
predictable initial state for the driver. The initial mode of the LAN87xx
PHY is determined by the AUTOMDIX_EN strap pin, but the driver has no
documented way to read its latched status.
This unpredictability means the driver cannot know if the PHY has
initialized with Auto-MDIX enabled or disabled, preventing it from
providing a reliable interface to the user.
This patch introduces a `config_init` hook that forces the PHY into a
known state by explicitly enabling Auto-MDIX.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a141af8eb2 ]
Correct the Auto-MDIX configuration to ensure userspace settings are
respected when the feature is disabled by the AUTOMDIX_EN hardware strap.
The LAN9500 PHY allows its default MDI-X mode to be configured via a
hardware strap. If this strap sets the default to "MDI-X off", the
driver was previously unable to enable Auto-MDIX from userspace.
When handling the ETH_TP_MDI_AUTO case, the driver would set the
SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required
SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY
falls back to its hardware strap default, ignoring the software request.
This patch corrects the behavior by also setting the override bit when
enabling Auto-MDIX. This ensures that the userspace configuration takes
precedence over the hardware strap, allowing Auto-MDIX to be enabled
correctly in all scenarios.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ab9ada765 ]
The previous commit unintentionally removed the code responsible for
enabling WoL via MMD3 register 0x8012 BIT5. As a result, Wake-on-LAN
(WoL) support for the QCA808X PHY is no longer functional.
The WoL (Wake-on-LAN) feature for the QCA808X PHY is enabled via MMD3
register 0x8012, BIT5. This implementation is aligned with the approach
used in at8031_set_wol().
Fixes: e58f30246c ("net: phy: at803x: fix the wol setting functions")
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250704-qcom_phy_wol_support-v1-2-053342b1538d@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e31cf3cce2 ]
Move the WoL (Wake-on-LAN) functionality to a shared library to enable
its reuse by the QCA808X PHY driver, incorporating support for WoL
functionality similar to the implementation in at8031_set_wol().
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://patch.msgid.link/20250704-qcom_phy_wol_support-v1-1-053342b1538d@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4ab9ada765 ("net: phy: qcom: qca808x: Fix WoL issue by utilizing at8031_set_wol()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8989bad541 upstream.
The first boards show up with Realtek's RTL8125D. This MAC/PHY chip
comes with an integrated 2.5Gbps PHY with ID 0x001cc841. It's not
clear yet whether there's an external version of this PHY and how
Realtek calls it, therefore use the numeric id for now.
Link: https://lore.kernel.org/netdev/2ada65e1-5dfa-456c-9334-2bc51272e9da@gmail.com/T/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <7d2924de-053b-44d2-a479-870dc3878170@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mathieu Tortuyaux <mtortuyaux@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f87a17ed3b upstream.
The Realtek RTL8125/RTL8126 NBase-T MAC/PHY chips have internal PHY's
which are register-compatible, at least for the registers we use here.
So let's use just one PHY driver to support all of them.
These internal PHY's exist also as external C45 PHY's, but on the
internal PHY's no access to MMD registers is possible. This can be
used to differentiate between the internal and external version.
As a side effect the drivers for two now external-only drivers don't
require read_mmd/write_mmd hooks any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c57081a6-811f-4571-ab35-34f4ca6de9af@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mathieu Tortuyaux <mtortuyaux@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 260388f79e ]
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via C45 (clause 45) mdiobus,
there is no verification of parameters passed to the ioctl and
it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before C45 read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes: 4e4aafcddb ("net: mdio: Add dedicated C45 API to MDIO bus drivers")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e62969412 ]
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via mdiobus, there is no verification of
parameters passed to the ioctl and it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes: 080bb352fa ("net: phy: Maintain MDIO device and bus statistics")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57a92d1465 ]
We have noticed that when PHY timestamping is enabled, L2 frames seems
to be modified by changing two 2 bytes with a value of 0. The place were
these 2 bytes seems to be random(or I couldn't find a pattern). In most
of the cases the userspace can ignore these frames but if for example
those 2 bytes are in the correction field there is nothing to do. This
seems to happen when configuring the HW for IPv4 even that the flow is
not enabled.
These 2 bytes correspond to the UDPv4 checksum and once we don't enable
clearing the checksum when using L2 frames then the frame doesn't seem
to be changed anymore.
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250523082716.2935895-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 846992645b ]
Fix memory leak when running one-step timestamping. When running
one-step sync timestamping, the HW is configured to insert the TX time
into the frame, so there is no reason to keep the skb anymore. As in
this case the HW will never generate an interrupt to say that the frame
was timestamped, then the frame will never released.
Fix this by freeing the frame in case of one-step timestamping.
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250522115722.2827199-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0795b05a59 ]
There is a potential crash issue when disabling and re-enabling the
network port. When disabling the network port, phy_detach() calls
device_link_del() to remove the device link, but it does not clear
phydev->devlink, so phydev->devlink is not a NULL pointer. Then the
network port is re-enabled, but if phy_attach_direct() fails before
calling device_link_add(), the code jumps to the "error" label and
calls phy_detach(). Since phydev->devlink retains the old value from
the previous attach/detach cycle, device_link_del() uses the old value,
which accesses a NULL pointer and causes a crash. The simplified crash
log is as follows.
[ 24.702421] Call trace:
[ 24.704856] device_link_put_kref+0x20/0x120
[ 24.709124] device_link_del+0x30/0x48
[ 24.712864] phy_detach+0x24/0x168
[ 24.716261] phy_attach_direct+0x168/0x3a4
[ 24.720352] phylink_fwnode_phy_connect+0xc8/0x14c
[ 24.725140] phylink_of_phy_connect+0x1c/0x34
Therefore, phydev->devlink needs to be cleared when the device link is
deleted.
Fixes: bc66fa87d4 ("net: phy: Add link between phy dev and mac dev")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250523083759.3741168-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a06a868a0c ]
Add .match_phy_device for the existing TJAs to differentiate between
TJA1103 and TJA1104.
TJA1103 and TJA1104 share the same PHY_ID but TJA1104 has MACsec
capabilities while TJA1103 doesn't.
Signed-off-by: Andrei Botila <andrei.botila@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250228154320.2979000-2-andrei.botila@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b63263555e ]
The phylink_expects_phy() function allows MAC drivers to check if they are
expecting a PHY to attach. The checking condition in phylink_expects_phy()
aims to achieve the same result as the checking condition in
phylink_attach_phy().
However, the checking condition in phylink_expects_phy() uses
pl->link_config.interface, while phylink_attach_phy() uses
pl->link_interface.
Initially, both pl->link_interface and pl->link_config.interface are set
to SGMII, and pl->cfg_link_an_mode is set to MLO_AN_INBAND.
When the interface switches from SGMII to 2500BASE-X,
pl->link_config.interface is updated by phylink_major_config().
At this point, pl->cfg_link_an_mode remains MLO_AN_INBAND, and
pl->link_config.interface is set to 2500BASE-X.
Subsequently, when the STMMAC interface is taken down
administratively and brought back up, it is blocked by
phylink_expects_phy().
Since phylink_expects_phy() and phylink_attach_phy() aim to achieve the
same result, phylink_expects_phy() should check pl->link_interface,
which never changes, instead of pl->link_config.interface, which is
updated by phylink_major_config().
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Link: https://patch.msgid.link/20250227121522.1802832-2-yong.liang.choong@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 30a41ed32d upstream.
With lan88xx based devices the lan78xx driver can get stuck in an
interrupt loop while bringing the device up, flooding the kernel log
with messages like the following:
lan78xx 2-3:1.0 enp1s0u3: kevent 4 may have been dropped
Removing interrupt support from the lan88xx PHY driver forces the
driver to use polling instead, which avoids the problem.
The issue has been observed with Raspberry Pi devices at least since
4.14 (see [1], bug report for their downstream kernel), as well as
with Nvidia devices [2] in 2020, where disabling interrupts was the
vendor-suggested workaround (together with the claim that phylib
changes in 4.9 made the interrupt handling in lan78xx incompatible).
Iperf reports well over 900Mbits/sec per direction with client in
--dualtest mode, so there does not seem to be a significant impact on
throughput (lan88xx device connected via switch to the peer).
[1] https://github.com/raspberrypi/linux/issues/2447
[2] https://forums.developer.nvidia.com/t/jetson-xavier-and-lan7800-problem/142134/11
Link: https://lore.kernel.org/0901d90d-3f20-4a10-b680-9c978e04ddda@lunn.ch
Fixes: 792aec47d5 ("add microchip LAN88xx phy driver")
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
Cc: kernel-list@raspberrypi.com
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250416102413.30654-1-fiona.klute@gmx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7f0ee992a ]
A network restart test on a router led to an out-of-memory condition,
which was traced to a memory leak in the PHY LED trigger code.
The root cause is misuse of the devm API. The registration function
(phy_led_triggers_register) is called from phy_attach_direct, not
phy_probe, and the unregister function (phy_led_triggers_unregister)
is called from phy_detach, not phy_remove. This means the register and
unregister functions can be called multiple times for the same PHY
device, but devm-allocated memory is not freed until the driver is
unbound.
This also prevents kmemleak from detecting the leak, as the devm API
internally stores the allocated pointer.
Fix this by replacing devm_kzalloc/devm_kcalloc with standard
kzalloc/kcalloc, and add the corresponding kfree calls in the unregister
path.
Fixes: 3928ee6485 ("net: phy: leds: Add support for "link" trigger")
Fixes: 2e0bc452f4 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Hao Guan <hao.guan@siflower.com.cn>
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250417032557.2929427-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ec5c085e ]
Add quirk for a copper SFP that identifies itself as "FS" "SFP-10GM-T".
It uses RollBall protocol to talk to the PHY and needs 4 sec wait before
probing the PHY.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://patch.msgid.link/20250227071058.1520027-1-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a850355610 ]
The OEM SFP-2.5G-BX10-D/U SFP module pair is meant to operate with
2500Base-X. However, in their EEPROM they incorrectly specify:
Transceiver codes : 0x00 0x12 0x00 0x00 0x12 0x00 0x01 0x05 0x00
BR, Nominal : 2500MBd
Use sfp_quirk_2500basex for this module to allow 2500Base-X mode anyway.
Tested on BananaPi R3.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/20250218-b4-lkmsub-v1-1-1e51dcabed90@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc75ea20ff ]
DSA has 2 kinds of drivers:
1. Those who call dsa_switch_suspend() and dsa_switch_resume() from
their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz
2. Those who don't: all others. The above methods should be optional.
For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(),
and dsa_switch_resume() calls dsa_user_resume() -> phylink_start().
These seem good candidates for setting mac_managed_pm = true because
that is essentially its definition [1], but that does not seem to be the
biggest problem for now, and is not what this change focuses on.
Talking strictly about the 2nd category of DSA drivers here (which
do not have MAC managed PM, meaning that for their attached PHYs,
mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full),
I have noticed that the following warning from mdio_bus_phy_resume() is
triggered:
WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY &&
phydev->state != PHY_UP);
because the PHY state machine is running.
It's running as a result of a previous dsa_user_open() -> ... ->
phylink_start() -> phy_start() having been initiated by the user.
The previous mdio_bus_phy_suspend() was supposed to have called
phy_stop_machine(), but it didn't. So this is why the PHY is in state
PHY_NOLINK by the time mdio_bus_phy_resume() runs.
mdio_bus_phy_suspend() did not call phy_stop_machine() because for
phylink, the phydev->adjust_link function pointer is NULL. This seems a
technicality introduced by commit fddd91016d ("phylib: fix PAL state
machine restart on resume"). That commit was written before phylink
existed, and was intended to avoid crashing with consumer drivers which
don't use the PHY state machine - phylink always does, when using a PHY.
But phylink itself has historically not been developed with
suspend/resume in mind, and apparently not tested too much in that
scenario, allowing this bug to exist unnoticed for so long. Plus, prior
to the WARN_ON(), it would have likely been invisible.
This issue is not in fact restricted to type 2 DSA drivers (according to
the above ad-hoc classification), but can be extrapolated to any MAC
driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where
the issue was reported. Assuming mac_managed_pm is set correctly, a
quick search indicates the following other drivers might be affected:
$ grep -Zlr PHYLINK_NETDEV drivers/ | xargs -0 grep -L mac_managed_pm
drivers/net/ethernet/atheros/ag71xx.c
drivers/net/ethernet/microchip/sparx5/sparx5_main.c
drivers/net/ethernet/microchip/lan966x/lan966x_main.c
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
drivers/net/ethernet/freescale/ucc_geth.c
drivers/net/ethernet/freescale/enetc/enetc_pf_common.c
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
drivers/net/ethernet/marvell/mvneta.c
drivers/net/ethernet/marvell/prestera/prestera_main.c
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/altera/altera_tse_main.c
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
drivers/net/ethernet/meta/fbnic/fbnic_phylink.c
drivers/net/ethernet/tehuti/tn40_phy.c
drivers/net/ethernet/mscc/ocelot_net.c
Make the existing conditions dependent on the PHY device having a
phydev->phy_link_change() implementation equal to the default
phy_link_change() provided by phylib. Otherwise, we implicitly know that
the phydev has the phylink-provided phylink_phy_change() callback, and
when phylink is used, the PHY state machine always needs to be stopped/
started on the suspend/resume path. The code is structured as such that
if phydev->phy_link_change() is absent, it is a matter of time until the
kernel will crash - no need to further complicate the test.
Thus, for the situation where the PM is not managed by the MAC, we will
make the MDIO bus PM ops treat identically the phylink-controlled PHYs
with the phylib-controlled PHYs where an adjust_link() callback is
supplied. In both cases, the MDIO bus PM ops should stop and restart the
PHY state machine.
[1] https://lore.kernel.org/netdev/Z-1tiW9zjcoFkhwc@shell.armlinux.org.uk/
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Reported-by: Wei Fang <wei.fang@nxp.com>
Tested-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250407094042.2155633-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f40a673d6b ]
In an upcoming change, mdio_bus_phy_may_suspend() will need to
distinguish a phylib-based PHY client from a phylink PHY client.
For that, it will need to compare the phydev->phy_link_change() function
pointer with the eponymous phy_link_change() provided by phylib.
To avoid forward function declarations, the default PHY link state
change method should be moved upwards. There is no functional change
associated with this patch, it is only to reduce the noise from a real
bug fix.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250407093900.2155112-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: fc75ea20ff ("net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f1eaabb4b ]
Correct detect condition is applied to the entire 5221 family of PHYs.
Fixes: 3abbd0699b ("net: phy: broadcom: add support for BCM5221 phy")
Signed-off-by: Jim Liu <jim.t90615@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3178d2b048 ]
xa_alloc_cyclic() can return 1, which isn't an error. To prevent
situation when the caller of this function will treat it as no error do
a check only for negative here.
Fixes: 3849687869 ("net: phy: Introduce ethernet link topology representation")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
