commit e383f09614 upstream.
Commit 53326135d0 ("i2c: riic: Add suspend/resume support") added
suspend support for the Renesas I2C driver and following this change
on RZ/G3E the following WARNING is seen on entering suspend ...
[ 134.275704] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[ 134.285536] ------------[ cut here ]------------
[ 134.290298] i2c i2c-2: Transfer while suspended
[ 134.295174] WARNING: drivers/i2c/i2c-core.h:56 at __i2c_smbus_xfer+0x1e4/0x214, CPU#0: systemd-sleep/388
[ 134.365507] Tainted: [W]=WARN
[ 134.368485] Hardware name: Renesas SMARC EVK version 2 based on r9a09g047e57 (DT)
[ 134.375961] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 134.382935] pc : __i2c_smbus_xfer+0x1e4/0x214
[ 134.387329] lr : __i2c_smbus_xfer+0x1e4/0x214
[ 134.391717] sp : ffff800083f23860
[ 134.395040] x29: ffff800083f23860 x28: 0000000000000000 x27: ffff800082ed5d60
[ 134.402226] x26: 0000001f4395fd74 x25: 0000000000000007 x24: 0000000000000001
[ 134.409408] x23: 0000000000000000 x22: 000000000000006f x21: ffff800083f23936
[ 134.416589] x20: ffff0000c090e140 x19: ffff0000c090e0d0 x18: 0000000000000006
[ 134.423771] x17: 6f63657320313030 x16: 2e30206465737061 x15: ffff800083f23280
[ 134.430953] x14: 0000000000000000 x13: ffff800082b16ce8 x12: 0000000000000f09
[ 134.438134] x11: 0000000000000503 x10: ffff800082b6ece8 x9 : ffff800082b16ce8
[ 134.445315] x8 : 00000000ffffefff x7 : ffff800082b6ece8 x6 : 80000000fffff000
[ 134.452495] x5 : 0000000000000504 x4 : 0000000000000000 x3 : 0000000000000000
[ 134.459672] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff0000c9ee9e80
[ 134.466851] Call trace:
[ 134.469311] __i2c_smbus_xfer+0x1e4/0x214 (P)
[ 134.473715] i2c_smbus_xfer+0xbc/0x120
[ 134.477507] i2c_smbus_read_byte_data+0x4c/0x84
[ 134.482077] isl1208_i2c_read_time+0x44/0x178 [rtc_isl1208]
[ 134.487703] isl1208_rtc_read_time+0x14/0x20 [rtc_isl1208]
[ 134.493226] __rtc_read_time+0x44/0x88
[ 134.497012] rtc_read_time+0x3c/0x68
[ 134.500622] rtc_suspend+0x9c/0x170
The warning is triggered because I2C transfers can still be attempted
while the controller is already suspended, due to inappropriate ordering
of the system sleep callbacks.
If the controller is autosuspended, there is no way to wake it up once
runtime PM disabled (in suspend_late()). During system resume, the I2C
controller will be available only after runtime PM is re-enabled
(in resume_early()). However, this may be too late for some devices.
Wake up the controller in the suspend() callback while runtime PM is
still enabled. The I2C controller will remain available until the
suspend_noirq() callback (pm_runtime_force_suspend()) is called. During
resume, the I2C controller can be restored by the resume_noirq() callback
(pm_runtime_force_resume()). Finally, the resume() callback re-enables
autosuspend. As a result, the I2C controller can remain available until
the system enters suspend_noirq() and from resume_noirq().
Cc: stable@vger.kernel.org
Fixes: 53326135d0 ("i2c: riic: Add suspend/resume support")
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0c50e3743 ]
The I2C Hub controller is a simpler GENI I2C variant that doesn't
support DMA at all, add a no_dma flag to make sure it nevers selects
the SE DMA mode with mappable 32bytes long transfers.
Fixes: cacd9643ec ("i2c: qcom-geni: add support for I2C Master Hub variant")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a6ee6aac66 upstream.
In i2c_amd_probe(), amd_mp2_find_device() utilizes
driver_find_next_device() which internally calls driver_find_device()
to locate the matching device. driver_find_device() increments the
reference count of the found device by calling get_device(), but
amd_mp2_find_device() fails to call put_device() to decrement the
reference count before returning. This results in a reference count
leak of the PCI device each time i2c_amd_probe() is executed, which
may prevent the device from being properly released and cause a memory
leak.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 529766e0a0 ("i2c: Add drivers for the AMD PCIe MP2 I2C controller")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20251022095402.8846-1-make24@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3429178ee ]
When probing the I2C master, disable SMBus interrupts to prevent
storms caused by broken firmware mis-configuring IC_SMBUS=1; the
handler never services them and a mis-configured SMBUS Master
extend-clock timeout or SMBUS Slave extend-clock timeout can
flood the CPU.
Signed-off-by: Jinhui Guo <guojinhui.liam@bytedance.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20251021075714.3712-2-guojinhui.liam@bytedance.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c149841b06 ]
After an error occurs during probing state, dw_i2c_plat_pm_cleanup() is
called. However, this function doesn't disable clocks and the clock-enable
count keeps increasing. Should disable these clocks explicitly.
Fixes: 7272194ed3 ("i2c-designware: add minimal support for runtime PM")
Co-developed-by: Kohei Ito <ito.kohei@socionext.com>
Signed-off-by: Kohei Ito <ito.kohei@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70e633bede ]
When the driver is removed, the clocks are first enabled by
calling pm_runtime_get_sync(), and then disabled with
pm_runtime_put_sync().
If CONFIG_PM=y, clocks for this controller are disabled when it's in
the idle state. So the clocks are properly disabled when the driver
exits.
Othewise, the clocks are always enabled and the PM functions have
no effect. Therefore, the driver exits without disabling the clocks.
# cat /sys/kernel/debug/clk/clk-pclk/clk_enable_count
18
# echo 1214a000.i2c > /sys/bus/platform/drivers/i2c_designware/bind
# cat /sys/kernel/debug/clk/clk-pclk/clk_enable_count
20
# echo 1214a000.i2c > /sys/bus/platform/drivers/i2c_designware/unbind
# cat /sys/kernel/debug/clk/clk-pclk/clk_enable_count
20
To ensure that the clocks can be disabled correctly even without
CONFIG_PM=y, should add the following fixes:
- Replace with pm_runtime_put_noidle(), which only decrements the runtime
PM usage count.
- Call i2c_dw_prepare_clk(false) to explicitly disable the clocks.
Fixes: 7272194ed3 ("i2c-designware: add minimal support for runtime PM")
Co-developed-by: Kohei Ito <ito.kohei@socionext.com>
Signed-off-by: Kohei Ito <ito.kohei@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b492183652 ]
The old IC does not support the I2C_MASTER_WRRD (write-then-read)
function, but the current code’s handling of i2c->auto_restart may
potentially lead to entering the I2C_MASTER_WRRD software flow,
resulting in unexpected bugs.
Instead of repurposing the auto_restart flag, add a separate flag
to signal I2C_MASTER_WRRD operations.
Also fix handling of msgs. If the operation (i2c->op) is
I2C_MASTER_WRRD, then the msgs pointer is incremented by 2.
For all other operations, msgs is simply incremented by 1.
Fixes: b2ed11e224 ("I2C: mediatek: Add driver for MediaTek MT8173 I2C controller")
Signed-off-by: Leilk.Liu <leilk.liu@mediatek.com>
Suggested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6a8e9f3de ]
The regmap is coming from the parent also in case of Xe
GPUs. Reusing the Wangxun quirk for that.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Co-developed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250701122252.2590230-3-heikki.krogerus@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo fixed the co-developed tags while merging]
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b7c9528fa ]
This patch fixes an issue where the touchpad cursor movement becomes
slow on the Dell Precision 5560. Force the touchpad freq to 100khz
as a workaround.
Tested on Dell Precision 5560 with 6.14 to 6.14.6. Cursor movement
is now smooth and responsive.
Signed-off-by: fangzhong.zhou <myth5@myth5.com>
[wsa: kept sorting and removed unnecessary parts from commit msg]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33ac515589 ]
If an error occurs in the loop that creates the device adapters, then a
reference to 'dev' still needs to be released.
Use for_each_child_of_node_scoped() to both fix the issue and save one line
of code.
Fixes: d0f8e97866 ("i2c: muxes: add support for tsd,mule-i2c multiplexer")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a663b3c47a upstream.
The current implementation uses wait_for_completion(), which can cause
the caller to hang indefinitely if the transfer never completes.
Switch to wait_for_completion_interruptible() so that the operation can
be interrupted by signals.
Fixes: 84e1d0bf1d ("i2c: virtio: disable timeout handling")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: <stable@vger.kernel.org> # v5.16+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/b8944e9cab8eb959d888ae80add6f2a686159ba2.1751541962.git.viresh.kumar@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56344e241c upstream.
The acpi_evaluate_object() returns an ACPI error code and not
Linux one. For the some platforms the err will have positive code
which may be interpreted incorrectly. Use device_reset() for
reset control which handles it correctly.
Fixes: bd2fdedbf2 ("i2c: tegra: Add the ACPI support")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Cc: <stable@vger.kernel.org> # v5.17+
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250710131206.2316-2-akhilrajeev@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7982a14b3 upstream.
Original logic only sets the return value but doesn't jump out of the
loop if the bus is kept active by a client. This is not expected. A
malicious or buggy i2c client can hang the kernel in this case and
should be avoided. This is observed during a long time test with a
PCA953x GPIO extender.
Fix it by changing the logic to not only sets the return value, but also
jumps out of the loop and return to the caller with -ETIMEDOUT.
Fixes: fbfab1ab06 ("i2c: qup: reorganization of driver code to remove polling for qup v1")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250616-qca-i2c-v1-1-2a8d37ee0a30@outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e66b0a8f04 upstream.
Using of_property_read_bool() for non-boolean properties is deprecated
and results in a warning during runtime since commit c141ecc3ce ("of:
Warn when of_property_read_bool() is used on non-boolean properties").
Fixes: b6ef830c60 ("i2c: omap: Add support for setting mux")
Cc: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250415075230.16235-1-johan+linaro@kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ef830c60 upstream.
Some SoCs require muxes in the routing for SDA and SCL lines.
Therefore, add support for setting the mux by reading the mux-states
property from the dt-node.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20250318103622.29979-3-j-choudhary@ti.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: a9503a2ecd ("i2c: omap: Handle omap_i2c_init() errors in omap_i2c_probe()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aae87fe7f upstream.
Before each I2C transfer using DMA, the I2C buffer is DMA'pped to make
sure the memory buffer is DMA'able. This is handle in the function
`stm32_i2c_prep_dma_xfer()`.
If the transfer fails for any reason the I2C buffer must be unmap.
Use the dma_callback to factorize the code and fix this issue.
Note that the `stm32f7_i2c_dma_callback()` is now called in case of DMA
transfer success and error and that the `complete()` on the dma_complete
completion structure is done inconditionnally in case of transfer
success or error as well as the `dmaengine_terminate_async()`.
This is allowed as a `complete()` in case transfer error has no effect
as well as a `dmaengine_terminate_async()` on a transfer success.
Also fix the unneeded cast and remove not more needed variables.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Cc: <stable@vger.kernel.org> # v4.18+
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250704-i2c-upstream-v4-2-84a095a2c728@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c870cbbd71 upstream.
If the DMA mapping failed, it produced an error log with the wrong
device name:
"stm32-dma3 40400000.dma-controller: rejecting DMA map of vmalloc memory"
Fix this issue by replacing the dev with the I2C dev.
Fixes: bb8822cbbc ("i2c: i2c-stm32: Add generic DMA API")
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Cc: <stable@vger.kernel.org> # v4.18+
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250704-i2c-upstream-v4-1-84a095a2c728@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d30048958 upstream.
The i2c_dw_xfer_init() function requires msgs and msg_write_idx from the
dev context to be initialized.
amd_i2c_dw_xfer_quirk() inits msgs and msgs_num, but not msg_write_idx.
This could allow an out of bounds access (of msgs).
Initialize msg_write_idx before calling i2c_dw_xfer_init().
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 17631e8ca2 ("i2c: designware: Add driver support for AMD NAVI GPU")
Cc: <stable@vger.kernel.org> # v5.13+
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250627143511.489570-1-michael.j.ruhl@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56ad91c1aa upstream.
This driver passes the length of an i2c_msg directly to
usb_control_msg(). If the message is now a read and of length 0, it
violates the USB protocol and a warning will be printed. Enable the
I2C_AQ_NO_ZERO_LEN_READ quirk for this adapter thus forbidding 0-length
read messages altogether.
Fixes: 83e53a8f12 ("i2c: Add bus driver for for OSIF USB i2c device.")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250522064234.3721-2-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbdb25ccf7 upstream.
This driver passes the length of an i2c_msg directly to
usb_control_msg(). If the message is now a read and of length 0, it
violates the USB protocol and a warning will be printed. Enable the
I2C_AQ_NO_ZERO_LEN_READ quirk for this adapter thus forbidding 0-length
read messages altogether.
Fixes: e8c76eed2e ("i2c: New i2c-tiny-usb bus driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # v2.6.22+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250522064349.3823-2-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38010591a0 ]
During init of the bus, the module checks that the bus is idle.
If one of the lines are stuck try to recover them first before failing.
Sometimes SDA and SCL are low if improper reset occurs (e.g., reboot).
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Mohammed Elbadry <mohammed.0.elbadry@gmail.com>
Reviewed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250328193252.1570811-1-mohammed.0.elbadry@gmail.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6e04f05ce ]
For SMBUS block read, do not continue to read if the message length
passed from the device is '0' or greater than the maximum allowed bytes.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250424053320.19211-1-akhilrajeev@nvidia.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fe2b969d9 ]
Replaced pm_runtime_put() with pm_runtime_put_sync_suspend() to ensure
the runtime suspend is invoked immediately when unregistering a slave.
This prevents a race condition where suspend was skipped when
unregistering and registering slave in quick succession.
For example, consider the rapid sequence of
`delete_device -> new_device -> delete_device -> new_device`.
In this sequence, it is observed that the dw_i2c_plat_runtime_suspend()
might not be invoked after `delete_device` operation.
This is because after `delete_device` operation, when the
pm_runtime_put() is about to trigger suspend, the following `new_device`
operation might race and cancel the suspend.
If that happens, during the `new_device` operation,
dw_i2c_plat_runtime_resume() is skipped (since there was no suspend), which
means `i_dev->init()`, i.e. i2c_dw_init_slave(), is skipped.
Since i2c_dw_init_slave() is skipped, i2c_dw_configure_fifo_slave() is
skipped too, which leaves `DW_IC_INTR_MASK` unconfigured. If we inspect
the interrupt mask register using devmem, it will show as zero.
Example shell script to reproduce the issue:
```
#!/bin/sh
SLAVE_LADDR=0x1010
SLAVE_BUS=13
NEW_DEVICE=/sys/bus/i2c/devices/i2c-$SLAVE_BUS/new_device
DELETE_DEVICE=/sys/bus/i2c/devices/i2c-$SLAVE_BUS/delete_device
# Create initial device
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
sleep 2
# Rapid sequence of
# delete_device -> new_device -> delete_device -> new_device
echo $SLAVE_LADDR > $DELETE_DEVICE
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
echo $SLAVE_LADDR > $DELETE_DEVICE
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
# Using devmem to inspect IC_INTR_MASK will show as zero
```
Signed-off-by: Tan En De <ende.tan@starfivetech.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250412023303.378600-1-ende.tan@starfivetech.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be7113d2e2 ]
If the clock i2c->clk was not enabled in i2c_pxa_probe(), it should not be
disabled in any path.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250212172803.1422136-1-mordan@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4f35233a6 ]
When the I2C QUP controller is used together with a DMA engine it needs
to vote for the interconnect path to the DRAM. Otherwise it may be
unable to access the memory quickly enough.
The requested peak bandwidth is dependent on the I2C core clock.
To avoid sending votes too often the bandwidth is always requested when
a DMA transfer starts, but dropped only on runtime suspend. Runtime
suspend should only happen if no transfer is active. After resumption we
can defer the next vote until the first DMA transfer actually happens.
The implementation is largely identical to the one introduced for
spi-qup in commit ecdaa94730 ("spi: qup: Vote for interconnect
bandwidth to DRAM") since both drivers represent the same hardware
block.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20231128-i2c-qup-dvfs-v1-3-59a0e3039111@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cfe51ef07 ]
If navi_amd_register_client() fails, the previous i2c_dw_probe() call
should be undone by a corresponding i2c_del_adapter() call, as already done
in the remove function.
Fixes: 17631e8ca2 ("i2c: designware: Add driver support for AMD NAVI GPU")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <stable@vger.kernel.org> # v5.13+
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/fcd9651835a32979df8802b2db9504c523a8ebbb.1747158983.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75caec0c2a ]
The fwnode.h is not supposed to be used by the drivers as it
has the definitions for the core parts for different device
property provider implementations. Drop it.
Note, that fwnode API for drivers is provided in property.h
which is included here.
Fixes: a076a860ac ("media: i2c: add I2C Address Translator (ATR) support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[wsa: reworded subject]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 285df995f9 upstream.
On the GTA04A5 writing a reset command to the gyroscope causes IRQ
storms because NACK IRQs are enabled and therefore triggered but not
acked.
Sending a reset command to the gyroscope by
i2cset 1 0x69 0x14 0xb6
with an additional debug print in the ISR (not the thread) itself
causes
[ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00
[ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1
[ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110)
[ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010)
[ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
repeating till infinity
[...]
(0x2 = NACK, 0x100 = Bus free, which is not enabled)
Apparently no other IRQ bit gets set, so this stalls.
Do not ignore enabled interrupts and make sure they are acked.
If the NACK IRQ is not needed, it should simply not enabled, but
according to the above log, caring about it is necessary unless
the Bus free IRQ is enabled and handled. The assumption that is
will always come with a ARDY IRQ, which was the idea behind
ignoring it, proves wrong.
It is true for simple reads from an unused address.
To still avoid the i2cdetect trouble which is the reason for
commit c770657bd2 ("i2c: omap: Fix standard mode false ACK readings"),
avoid doing much about NACK in omap_i2c_xfer_data() which is used
by both IRQ mode and polling mode, so also the false detection fix
is extended to polling usage and IRQ storms are avoided.
By changing this, the hardirq handler is not needed anymore to filter
stuff.
The mentioned gyro reset now just causes a -ETIMEDOUT instead of
hanging the system.
Fixes: c770657bd2 ("i2c: omap: Fix standard mode false ACK readings").
CC: stable@kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71c49ee9bb upstream.
According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Fixes: 015e61f0bf ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: stable@vger.kernel.org # v6.3+
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220125612.1910990-1-zhoubinbin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfd74cd1fb ]
When a 400KHz freq is used on this model of ELAN touchpad in Linux,
excessive smoothing (similar to when the touchpad's firmware detects
a noisy signal) is sometimes applied. As some devices' (e.g, Lenovo
V15 G4) ACPI tables specify a 400KHz frequency for this device and
some I2C busses (e.g, Designware I2C) default to a 400KHz freq,
force the speed to 100KHz as a workaround.
For future investigation: This problem may be related to the default
HCNT/LCNT values given by some busses' drivers, because they are not
specified in the aforementioned devices' ACPI tables, and because
the device works without issues on Windows at what is expected to be
a 400KHz frequency. The root cause of the issue is not known.
Signed-off-by: Randolph Ha <rha051117@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0a4e9fa65 ]
DEFAULT_SYMBOL_NAMESPACE must already be defined when <linux/export.h>
is included. So move the define above the include block.
Fixes: fd57a3325a ("i2c: designware: Move exports to I2C_DW namespaces")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceb8bf2cea ]
Commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 2505f87eb3 ("hwmon: (nct6775): Actually make use of the HWMON_NCT6775 symbol namespace")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cefc479cbb upstream.
i2c-atr catches the BUS_NOTIFY_DEL_DEVICE event on the bus and removes
the translation by calling i2c_atr_detach_client().
However, BUS_NOTIFY_DEL_DEVICE happens when the device is about to be
removed from this bus, i.e. before removal, and thus before calling
.remove() on the driver. If the driver happens to do any i2c
transactions in its remove(), they will fail.
Fix this by catching BUS_NOTIFY_REMOVED_DEVICE instead, thus removing
the translation only after the device is actually removed.
Fixes: a076a860ac ("media: i2c: add I2C Address Translator (ATR) support")
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Tested-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ad30f7890 ]
This backend requests a NACK from the controller driver when it detects
an error. If that request gets ignored from some reason, subsequent
accesses will wrongly be handled OK. To fix this, an error now changes
the state machine, so the backend will report NACK until a STOP
condition has been detected. This make the driver more robust against
controllers which will sadly apply the NACK not to the current byte but
the next one.
Fixes: a8335c64c5 ("i2c: add slave testunit driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 093f70c134 ]
When this controller is a target, the NACK handling had two issues.
First, the return value from the backend was not checked on the initial
WRITE_REQUESTED. So, the driver missed to send a NACK in this case.
Also, the NACK always arrives one byte late on the bus, even in the
WRITE_RECEIVED case. This seems to be a HW issue. We should then not
rely on the backend to correctly NACK the superfluous byte as well. Fix
both issues by introducing a flag which gets set whenever the backend
requests a NACK and keep sending it until we get a STOP condition.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca89f73394 ]
When misconfigured, the initial setup of the current mux channel can
fail, too. It must be checked as well.
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f8c4f5e9a ]
The reference count of the device incremented in device_initialize() is
not decremented when device_add() fails. Add a put_device() call before
returning from the function.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 60f6859702 ("i2c: core: Setup i2c_adapter runtime-pm before calling device_add()")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 49e1f0fd0d upstream.
Running i2c-detect currently produces an output akin to:
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: 08 -- 0a -- 0c -- 0e --
10: 10 -- 12 -- 14 -- 16 -- UU 19 -- 1b -- 1d -- 1f
20: -- 21 -- 23 -- 25 -- 27 -- 29 -- 2b -- 2d -- 2f
30: -- -- -- -- -- -- -- -- 38 -- 3a -- 3c -- 3e --
40: 40 -- 42 -- 44 -- 46 -- 48 -- 4a -- 4c -- 4e --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: 60 -- 62 -- 64 -- 66 -- 68 -- 6a -- 6c -- 6e --
70: 70 -- 72 -- 74 -- 76 --
This happens because for an i2c_msg with a len of 0 the driver will
mark the transmission of the message as a success once the START has
been sent, without waiting for the devices on the bus to respond with an
ACK/NAK. Since i2cdetect seems to run in a tight loop over all addresses
the NAK is treated as part of the next test for the next address.
Delete the fast path that marks a message as complete when idev->msg_len
is zero after sending a START/RESTART since this isn't a valid scenario.
CC: stable@vger.kernel.org
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241218-outbid-encounter-b2e78b1cc707@spud
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0cec36319 upstream.
Compatible string "fsl,imx7d-i2c" is not exited at i2c-imx driver
compatible string table, at the result, "fsl,imx21-i2c" will be
matched, but it will cause erratum ERR007805 not be applied in fact.
So Add "fsl,imx7d-i2c" compatible string in i2c-imx driver to apply
the erratum ERR007805(https://www.nxp.com/docs/en/errata/IMX7DS_3N09P.pdf).
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
"fsl,imx7d-i2c" already is documented in binding doc. This erratum
fix has been included in imx6_i2c_hwdata and it is the same in all
I.MX6/7/8, so just reuse it.
Fixes: 39c025721d ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Fixes: 39c025721d ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit")
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20241218044238.143414-1-carlos.song@nxp.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a8f9320d6 upstream.
At present, where repeated sends are intended to be used, the
i2c-microchip-core driver sends a stop followed by a start. Lots of i2c
devices must not malfunction in the face of this behaviour, because the
driver has operated like this for years! Try to keep track of whether or
not a repeated send is required, and suppress sending a stop in these
cases.
CC: stable@vger.kernel.org
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241218-football-composure-e56df2461461@spud
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
