[ Upstream commit eabf273c84 ]
The i2s2_data function is available on both gpio12 and gpio13. Fix the
groups definition.
Fixes: 6e261d1090 ("pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f0d22ec60 ]
GPIO controller driver should typically implement the .get_direction()
callback as GPIOLIB internals may try to use it to determine the state
of a pin. Add it for the LPASS LPI driver.
Reported-by: Abel Vesa <abelvesa@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 6e261d1090 ("pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # X1E CRD
Tested-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
[ PIN_CONFIG_LEVEL => PIN_CONFIG_OUTPUT ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1fbe3abb44 ]
Qualcomm SC7280 and SM8350 SoCs have slightly different LPASS audio
blocks (v9.4.5 and v9.2), however the LPASS LPI pin controllers are
exactly the same. The driver for SM8350 has two issues, which can be
fixed by simply moving over to SC7280 driver which has them correct:
1. "i2s2_data_groups" listed twice GPIO12, but should have both GPIO12
and GPIO13,
2. "swr_tx_data_groups" contained GPIO5 for "swr_tx_data2" function, but
that function is also available on GPIO14, thus listing it twice is
not necessary. OTOH, GPIO5 has also "swr_rx_data1", so selecting
swr_rx_data function should not block the TX one.
Fixes: be9f6d5638 ("pinctrl: qcom: sm8350-lpass-lpi: add SM8350 LPASS TLMM")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
[ .remove_new vs .remove ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c2e70397b ]
Replace disable_irq() with disable_irq_nosync() in msm_pinmux_set_mux()
to prevent deadlock when wakeup IRQ is triggered on the same
GPIO being reconfigured.
The issue occurs when a wakeup IRQ is triggered on a GPIO and the IRQ
handler attempts to reconfigure the same GPIO's pinmux. In this scenario,
msm_pinmux_set_mux() calls disable_irq() which waits for the currently
running IRQ handler to complete, creating a circular dependency that
results in deadlock.
Using disable_irq_nosync() avoids waiting for the IRQ handler to
complete, preventing the deadlock condition while still properly
disabling the interrupt during pinmux reconfiguration.
Suggested-by: Prasad Sodagudi <prasad.sodagudi@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 93712205ce upstream.
On some platforms, the UFS-reset pin has no interrupt logic in TLMM but
is nevertheless registered as a GPIO in the kernel. This enables the
user-space to trigger a BUG() in the pinctrl-msm driver by running, for
example: `gpiomon -c 0 113` on RB2.
The exact culprit is requesting pins whose intr_detection_width setting
is not 1 or 2 for interrupts. This hits a BUG() in
msm_gpio_irq_set_type(). Potentially crashing the kernel due to an
invalid request from user-space is not optimal, so let's go through the
pins and mark those that would fail the check as invalid for the irq chip
as we should not even register them as available irqs.
This function can be extended if we determine that there are more
corner-cases like this.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Cc: stable@vger.kernel.org
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/20250612091448.41546-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41e452e693 ]
Error-handling paths in msm_pinctrl_probe() don't call
a function required to unroll restart handler registration,
unregister_restart_handler(). Instead of adding calls to this function,
switch the msm pinctrl code into using devm_register_sys_off_handler().
Fixes: cf1fc18762 ("pinctrl: qcom: use restart_notifier mechanism for ps_hold")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250513-pinctrl-msm-fix-v2-2-249999af0fc1@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e225128c3f upstream.
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
Cc: stable@vger.kernel.org
Fixes: cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts when enabling")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20250312-pinctrl-msm-type-latch-v1-1-ce87c561d3d7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bc0ebfb1d upstream.
Commit 723e8462a4 ("pinctrl: qcom: spmi-gpio: Fix the GPIO strength
mapping") fixed a long-standing issue in the Qualcomm SPMI PMIC gpio
driver which had the 'low' and 'high' drive strength settings switched
but failed to update the debugfs interface which still gets this wrong.
Fix the debugfs code so that the exported values match the hardware
settings.
Note that this probably means that most devicetrees that try to describe
the firmware settings got this wrong if the settings were derived from
debugfs. Before the above mentioned commit the settings would have
actually matched the firmware settings even if they were described
incorrectly, but now they are inverted.
Fixes: 723e8462a4 ("pinctrl: qcom: spmi-gpio: Fix the GPIO strength mapping")
Fixes: eadff30244 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Cc: Anjelique Melendez <quic_amelende@quicinc.com>
Cc: stable@vger.kernel.org # 3.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/20241025121622.1496-1-johan+linaro@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On X1E80100, GPIO interrupts for wakeup-capable pins have been broken since
the introduction of the pinctrl driver. This prevents keyboard and touchpad
from working on most of the X1E laptops. So far we have worked around this
by manually building a kernel with the "wakeup-parent" removed from the
pinctrl node in the device tree, but we cannot expect all users to do that.
Implement a similar workaround in the driver by clearing the wakeirq_map
for X1E80100. This avoids using the PDC wakeup parent for all GPIOs
and handles the interrupts directly in the pinctrl driver instead.
The PDC driver needs additional changes to support X1E80100 properly.
Adding a workaround separately first allows to land the necessary PDC
changes through the normal release cycle, while still solving the more
critical problem with keyboard and touchpad on the current stable kernel
versions. Bypassing the PDC is enough for now, because we have not yet
enabled the deep idle states where using the PDC becomes necessary.
Cc: stable@vger.kernel.org
Fixes: 05e4941d97 ("pinctrl: qcom: Add X1E80100 pinctrl driver")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/20240830-x1e80100-bypass-pdc-v1-1-d4c00be0c3e3@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove the erroneus 0x100000 offset to prevent the boards from crashing
on pin state setting, as well as for the intended state changes to take
effect.
Fixes: 05e4941d97 ("pinctrl: qcom: Add X1E80100 pinctrl driver")
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20240809-topic-h_sdc-v1-1-bb421532c531@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current map seems to be out of sync (and includes a duplicate entry
for GPIO193..).
Replace it with the map present in shipping devices' ACPI tables.
This new one seems more complete, as it e.g. contains GPIO145 (PCIE6a
WAKE#)
Fixes: 05e4941d97 ("pinctrl: qcom: Add X1E80100 pinctrl driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Link: https://lore.kernel.org/20240711-topic-x1e_pdc_tlmm-v1-1-e278b249d793@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the pin controller block on SM4250 Low Power Island.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/20240612-sm4250-lpi-v4-2-a0342e47e21b@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PDC was hooked up as a wakeup parent in the DTS in
commit 71f080633d ("arm64: dts: qcom: sdm670: Hook up PDC as
wakeup-parent of TLMM"), but the wakeirq mapping was not defined so it
had no effect. Add the mapping for wakeup interrupts on the PDC to their
corresponding pins.
Configuring a pin IRQ as dual-edge would break it unless the
wakeirq_dual_edge_errata flag is set.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20240523230619.256882-2-mailingradian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PMC8380 is a new chip, featuring 10 GPIOs. Describe it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240525-topic-pmc8380_gpio-v2-2-2de50cb28ac1@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPMI GPIO driver assumes that the parent device is an SPMI device
and accesses random data when backcasting the parent struct device
pointer for non-SPMI devices.
Fortunately this does not seem to cause any issues currently when the
parent device is an I2C client like the PM8008, but this could change if
the structures are reorganised (e.g. using structure randomisation).
Notably the interrupt implementation is also broken for non-SPMI devices.
Also note that the two GPIO pins on PM8008 are used for interrupts and
reset so their practical use should be limited.
Drop the broken GPIO support for PM8008 for now.
Fixes: ea119e5a48 ("pinctrl: qcom-pmic-gpio: Add support for pm8008")
Cc: stable@vger.kernel.org # 5.13
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240529162958.18081-9-johan+linaro@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table. Pin controllers are
considered core components, so usually they are built-in, however these
can be built and used as modules on some generic kernel.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Message-ID: <20240411064614.7409-4-krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for qcom,pmih0108-gpio and qcom,pmd8028-gpio.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Message-ID: <20240326220628.2392802-5-quic_amelende@quicinc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for qcom,pmxr2230-gpio and qcom,pm6450-gpio.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Message-ID: <20240326220628.2392802-4-quic_amelende@quicinc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
remove the second #include <linux/seq_file.h>
Signed-off-by: Wang Jinchao <wangjinchao@xfusion.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/202312151810+0800-wangjinchao@xfusion.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver for TLMM block found in SM4450 SoC.
Can Guo helped out in reviewing the driver.
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Link: https://lore.kernel.org/r/20231212094900.12615-3-quic_tengfan@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinconf-groups debugfs file dumps each valid configuration item of
all pin groups. Some platforms and devices may have pin groups which
cannot be accessed, according to commit 691bf5d5a7 ("pinctrl: qcom:
Don't allow protected pins to be requested"). Fail for each
configuration item of an invalid pin group by checking the GPIO chip's
valid mask.
The validity of the pin group cannot be checked in the generic pinconf
dump (function "pinconf_generic_dump_one"), as it does not directly
interact with the gpiochip or the pinmux callbacks (which would give it
access to the request callback). Instead, an entry contains the ID and
name of the pingroup with no properties when all items fail.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20231128020202.728156-3-mailingradian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration with pinctrl
framework for X1E80100 SoC.
Co-developed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231117093921.31968-3-quic_sibis@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Existing Qualcomm SoCs have the LPASS pin controller slew rate control
in separate register, however this will change with upcoming Qualcomm
SoCs. The slew rate will be part of the main register for pin
configuration, thus second device IO address space is not needed.
Prepare for supporting new SoCs by adding flag customizing the driver
behavior for slew rate.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231013145935.220945-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting slew rate for each pin will grow with upcoming Qualcomm SoCs,
so split the code responsible for this into separate function for easier
readability and maintenance.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231013145935.220945-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New platforms uses a new set of bits to control the wakeirq
delivery to the PDC block.
The intr_wakeup_present_bit indicates if the GPIO supports
wakeirq and intr_wakeup_enable_bit enables wakeirq delivery
to the PDC block.
While the name seems to imply this only enables wakeup events,
it is required to allow interrupts events to the PDC block.
Enable this bit in the irq resource request/free if:
- gpio is in wakeirq map
- has the intr_wakeup_present_bit
- the intr_wakeup_enable_bit is set
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231106-topic-sm8650-upstream-tlmm-v3-2-0e179c368933@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for the pin controller in Low Power Audio SubSystem (LPASS)
of Qualcomm SM8650 SoC.
Notable differences against SM8550 LPASS pin controller:
1. Additional address space for slew rate thus driver uses
LPI_FLAG_SLEW_RATE_SAME_REG and sets slew rate via different
register.
2. Two new pin mux functions: qca_swr_clk and qca_swr_data
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231027093615.140656-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- Realtek RTD family pin control driver and RTD1619B,
RTD1319D and RTD1315E subdrivers.
- Nuvoton NPCM8xx combined pin control and GPIO driver.
- Amlogic T7 pin control driver.
- Renesas RZ/G3S pin control driver.
Improvements:
- A number of additional UART groups added to the Mediatek
MT7981 driver.
- MPM pin maps added for Qualcomm MSM8996, SM6115, SM6125
and SDM660.
- Extra GPIO banks for the Sunxi H616.
- MLSP I2C6 function support in Qualcomm MSM8226.
- Some __counted_by() annotations for dynamic arrays.
- Ongoing work to make remove() return void.
- LSBC groups and functions in the Renesas R8A7778.
-----BEGIN PGP SIGNATURE-----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=vonG
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No pin control core changes this time.
New drivers:
- Realtek RTD family pin control driver and RTD1619B, RTD1319D and
RTD1315E subdrivers
- Nuvoton NPCM8xx combined pin control and GPIO driver
- Amlogic T7 pin control driver
- Renesas RZ/G3S pin control driver
Improvements:
- A number of additional UART groups added to the Mediatek MT7981
driver
- MPM pin maps added for Qualcomm MSM8996, SM6115, SM6125 and SDM660
- Extra GPIO banks for the Sunxi H616
- MLSP I2C6 function support in Qualcomm MSM8226
- Some __counted_by() annotations for dynamic arrays
- Ongoing work to make remove() return void
- LSBC groups and functions in the Renesas R8A7778"
* tag 'pinctrl-v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (110 commits)
pinctrl: Use device_get_match_data()
dt-bindings: pinctrl: qcom,sa8775p-tlmm: add missing wakeup-parent
dt-bindings: pinctrl: nuvoton,npcm845: Add missing additionalProperties on gpio child nodes
dt-bindings: pinctrl: brcm: Ensure all child node properties are documented
pinctrl: renesas: rzn1: Convert to platform remove callback returning void
pinctrl: renesas: rzg2l: Add RZ/G3S support
dt-bindings: pinctrl: renesas: Document RZ/G3S SoC
pinctrl: renesas: rzg2l: Add support for different DS values on different groups
pinctrl: renesas: rzg2l: Move DS and OI to SoC-specific configuration
pinctrl: renesas: rzg2l: Adapt function number for RZ/G3S
pinctrl: renesas: rzg2l: Adapt for different SD/PWPR register offsets
pinctrl: renesas: rzg2l: Index all registers based on port offset
pinctrl: renesas: rzg2l: Add validation of GPIO pin in rzg2l_gpio_request()
pinctrl: renesas: r8a7778: Add LBSC pins, groups, and functions
pinctrl: intel: fetch community only when we need it
pinctrl: cherryview: reduce scope of PIN_CONFIG_BIAS_HIGH_IMPEDANCE case
pinctrl: cherryview: Convert to platform remove callback returning void
pinctrl: sprd-sc9860: Convert to platform remove callback returning void
pinctrl: qcom/msm: Convert to platform remove callback returning void
pinctrl: qcom/lpi: Convert to platform remove callback returning void
...
The Qualcomm LPASS LPI pin controller driver uses one lock for guarding
Read-Modify-Write code for slew rate registers. However the pin
configuration and muxing registers have exactly the same RMW code but
are not protected.
Pin controller framework does not provide locking here, thus it is
possible to trigger simultaneous change of pin configuration registers
resulting in non-atomic changes.
Protect from concurrent access by re-using the same lock used to cover
the slew rate register. Using the same lock instead of adding second
one will make more sense, once we add support for newer Qualcomm SoC,
where slew rate is configured in the same register as pin
configuration/muxing.
Fixes: 6e261d1090 ("pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver")
Cc: stable@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231013145705.219954-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
To convert all those qcom pinctrl drivers, make msm_pinctrl_remove()
return void (instead of zero) and use .remove_new in all drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009162510.335208-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
To convert all those qcom pinctrl drivers, make msm_pinctrl_remove()
return void (instead of zero) and use .remove_new in all drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009162510.335208-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pin <-> wakeirq mappings to allow for waking up the AP from sleep
through MPM-connected pins.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20230923131432.21721-3-matti.lehtimaki@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pin <-> wakeirq mappings to allow for waking up the AP from sleep
through MPM-connected pins.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20230923131432.21721-2-matti.lehtimaki@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On GPIO22 and GPIO23 there is another I2C bus. Add the function for it.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230922-msm8226-i2c6-v2-2-3fb55c47a084@z3ntu.xyz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
