commit e9c206324e upstream.
The cdnsp-pci driver uses pcim_enable_device() to enable a PCI device,
which means the device will be automatically disabled on driver detach
through the managed device framework. The manual pci_disable_device()
call in the error path is therefore redundant.
Found via static anlaysis and this is similar to commit 99ca0b57e4
("thermal: intel: int340x: processor: Fix warning during module unload").
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20250903141613.2535472-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be5ae730ff upstream.
Right now the interrupt handler first reads all updated status registers
and only then clears the interrupts. It's possible that a duplicate
interrupt for a changed register or plug state comes in after the
interrupts have been processed but before they have been cleared:
* plug is inserted, TPS_REG_INT_PLUG_EVENT is set
* TPS_REG_INT_EVENT1 is read
* tps6598x_handle_plug_event() has run and registered the plug
* plug is removed again, TPS_REG_INT_PLUG_EVENT is set (again)
* TPS_REG_INT_CLEAR1 is written, TPS_REG_INT_PLUG_EVENT is cleared
We then have no plug connected and no pending interrupt but the tipd
core still thinks there is a plug. It's possible to trigger this with
e.g. a slightly broken Type-C to USB A converter.
Fix this by first clearing the interrupts and only then reading the
updated registers.
Fixes: 45188f27b3 ("usb: typec: tipd: Add support for Apple CD321X")
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Cc: stable@kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://lore.kernel.org/r/20250914-apple-usb3-tipd-v1-1-4e99c8649024@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e40b984b6c ]
The VHCI platform driver aims to forbid entering system suspend when at
least one of the virtual USB ports are bound to an active USB/IP
connection.
However, in some cases, the detection logic doesn't work reliably, i.e.
when all devices attached to the virtual root hub have been already
suspended, leading to a broken suspend state, with unrecoverable resume.
Ensure the virtually attached devices do not enter suspend by setting
the syscore PM flag. Note this is currently limited to the client side
only, since the server side doesn't implement system suspend prevention.
Fixes: 04679b3489 ("Staging: USB/IP: add client driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250902-vhci-hcd-suspend-fix-v3-1-864e4e833559@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08fa726e66 ]
This reverts commit 28a76fcc4c.
No actual HW bugs are known where Endpoint Context shows Running state
but Stop Endpoint fails repeatedly with Context State Error and leaves
the endpoint state unchanged. Stop Endpoint retries on Running EPs have
been performed since early 2021 with no such issues reported so far.
Trying to handle this hypothetical case brings a more realistic danger:
if Stop Endpoint fails on an endpoint which hasn't yet started after a
doorbell ring and enough latency occurs before this completion event is
handled, the driver may time out and begin removing cancelled TDs from
a running endpoint, even though one more retry would stop it reliably.
Such high latency is rare but not impossible, and removing TDs from a
running endpoint can cause more damage than not giving back a cancelled
URB (which wasn't happening anyway). So err on the side of caution and
revert to the old policy of always retrying if the EP appears running.
[Remove stable tag as we are dealing with theoretical cases -Mathias]
Fixes: 28a76fcc4c ("usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running")
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250917210726.97100-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e271cc0d25 ]
Once the use_os_string flag is set to true for some functions
(e.g. adb/mtp) which need to response the OS string, and then
if we re-bind the ConfigFS gadget to use the other functions
(e.g. hid) which should not to response the OS string, however,
because the use_os_string flag is still true, so the usb gadget
response the OS string descriptor incorrectly, this can cause
the USB device to be unrecognizable on the Windows system.
An example of this as follows:
echo 1 > os_desc/use
ln -s functions/ffs.adb configs/b.1/function0
start adbd
echo "<udc device>" > UDC #succeed
stop adbd
rm configs/b.1/function0
echo 0 > os_desc/use
ln -s functions/hid.gs0 configs/b.1/function0
echo "<udc device>" > UDC #fail to connect on Windows
This patch sets the use_os_string flag to false at bind if
the functions not support OS Descriptors.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Fixes: 87213d388e ("usb: gadget: configfs: OS String support")
Link: https://lore.kernel.org/r/1755833769-25434-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b570b346dd ]
In the twl6030_usb_probe(), the variable ret is declared as
a u32 type. However, since ret may receive -ENODEV when accepting
the return value of omap_usb2_set_comparator().Therefore, its type
should be changed to int.
Fixes: 0e98de67ba ("usb: otg: make twl6030_usb as a comparator driver to omap_usb2")
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Link: https://lore.kernel.org/r/20250822092224.30645-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0485e864a ]
EUD_MODE_MANAGER2 register is mapped to a memory region that is marked
as read-only for operating system running at EL1, enforcing access
restrictions that prohibit direct memory-mapped writes via writel().
Attempts to write to this region from HLOS can result in silent failures
or memory access violations, particularly when toggling EUD (Embedded
USB Debugger) state. To ensure secure register access, modify the driver
to use qcom_scm_io_writel(), which routes the write operation to Qualcomm
Secure Channel Monitor (SCM). SCM has the necessary permissions to access
protected memory regions, enabling reliable control over EUD state.
SC7280, the only user of EUD is also affected, indicating that this could
never have worked on a properly fused device.
Fixes: 9a1bf58ccd ("usb: misc: eud: Add driver support for Embedded USB Debugger(EUD)")
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Signed-off-by: Komal Bajaj <komal.bajaj@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250731-eud_mode_manager_secure_access-v8-1-4a5dcbb79f41@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 186e8f2bdb ]
The kthread_run() function returns error pointers so the
max3421_hcd->spi_thread pointer can be either error pointers or NULL.
Check for both before dereferencing it.
Fixes: 05dfa5c9bc ("usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/aJTMVAPtRe5H6jug@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Here are some new modem device ids.
Everything has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCaMPXVAAKCRALxc3C7H1l
CIToAQDoULIp/C7gzVUPgHpIeMGPHspAsVqjZ5TDO0Bhc6oM4QEAtpsmzbiZ76xh
jxTtlUiCmVedSTu/OMRTXW2Xz/CRgAU=
=U3Rs
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.17-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB serial device ids for 6.17-rc6
Here are some new modem device ids.
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-6.17-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit Cinterion LE910C4-WWX new compositions
USB: serial: option: add Telit Cinterion FN990A w/audio compositions
The EP-IN of MIDI2 (altset 1) wasn't initialized in
f_midi2_create_usb_configs() as it's an INT EP unlike others BULK
EPs. But this leaves rather the max packet size unchanged no matter
which speed is used, resulting in the very slow access.
And the wMaxPacketSize values set there look legit for INT EPs, so
let's initialize the MIDI2 EP-IN there for achieving the equivalent
speed as well.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250905133240.20966-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget card driver forgot to call snd_ump_update_group_attrs()
after adding FBs, and this leaves the UMP group attributes
uninitialized. As a result, -ENODEV error is returned at opening a
legacy rawmidi device as an inactive group.
This patch adds the missing call to address the behavior above.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250904153932.13589-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_handle_vdm_request delivers messages to the partner altmode or the
cable altmode depending on the SVDM response type, which is incorrect.
The partner or cable should be chosen based on the received message type
instead.
Also add this filter to ADEV_NOTIFY_USB_AND_QUEUE_VDM, which is used when
the Enter Mode command is responded to by a NAK on SOP or SOP' and when
the Exit Mode command is responded to by an ACK on SOP.
Fixes: 7e7877c55e ("usb: typec: tcpm: add alt mode enter/exit/vdm support for sop'")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250821203759.1720841-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yunseong Kim and the syzbot fuzzer both reported a problem in
RT-enabled kernels caused by the way dummy-hcd mixes interrupt
management and spin-locking. The pattern was:
local_irq_save(flags);
spin_lock(&dum->lock);
...
spin_unlock(&dum->lock);
... // calls usb_gadget_giveback_request()
local_irq_restore(flags);
The code was written this way because usb_gadget_giveback_request()
needs to be called with interrupts disabled and the private lock not
held.
While this pattern works fine in non-RT kernels, it's not good when RT
is enabled. RT kernels handle spinlocks much like mutexes; in particular,
spin_lock() may sleep. But sleeping is not allowed while local
interrupts are disabled.
To fix the problem, rewrite the code to conform to the pattern used
elsewhere in dummy-hcd and other UDC drivers:
spin_lock_irqsave(&dum->lock, flags);
...
spin_unlock(&dum->lock);
usb_gadget_giveback_request(...);
spin_lock(&dum->lock);
...
spin_unlock_irqrestore(&dum->lock, flags);
This approach satisfies the RT requirements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Fixes: b4dbda1a22 ("USB: dummy-hcd: disable interrupts during req->complete")
Reported-by: Yunseong Kim <ysk@kzalloc.com>
Closes: <https://lore.kernel.org/linux-usb/5b337389-73b9-4ee4-a83e-7e82bf5af87a@kzalloc.com/>
Reported-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
Closes: <https://lore.kernel.org/linux-usb/68ac2411.050a0220.37038e.0087.GAE@google.com/>
Tested-by: syzbot+8baacc4139f12fa77909@syzkaller.appspotmail.com
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
CC: stable@vger.kernel.org
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/bb192ae2-4eee-48ee-981f-3efdbbd0d8f0@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend-resume cycle test revealed a memory leak in 6.17-rc3
Turns out the slot_id race fix changes accidentally ends up calling
xhci_free_virt_device() with an incorrect vdev parameter.
The vdev variable was reused for temporary purposes right before calling
xhci_free_virt_device().
Fix this by passing the correct vdev parameter.
The slot_id race fix that caused this regression was targeted for stable,
so this needs to be applied there as well.
Fixes: 2eb0337615 ("usb: xhci: Fix slot_id resource race conflict")
Reported-by: David Wang <00107082@163.com>
Closes: https://lore.kernel.org/linux-usb/20250829181354.4450-1-00107082@163.com
Suggested-by: Michal Pecio <michal.pecio@gmail.com>
Suggested-by: David Wang <00107082@163.com>
Cc: stable@vger.kernel.org
Tested-by: David Wang <00107082@163.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pending requests will be flushed on disconnect, and the corresponding
TRBs will be turned into No-op TRBs, which are ignored by the xHC
controller once it starts processing the ring.
If the USB debug cable repeatedly disconnects before ring is started
then the ring will eventually be filled with No-op TRBs.
No new transfers can be queued when the ring is full, and driver will
print the following error message:
"xhci_hcd 0000:00:14.0: failed to queue trbs"
This is a normal case for 'in' transfers where TRBs are always enqueued
in advance, ready to take on incoming data. If no data arrives, and
device is disconnected, then ring dequeue will remain at beginning of
the ring while enqueue points to first free TRB after last cancelled
No-op TRB.
s
Solve this by reinitializing the rings when the debug cable disconnects
and DbC is leaving the configured state.
Clear the whole ring buffer and set enqueue and dequeue to the beginning
of ring, and set cycle bit to its initial state.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Decouple allocation of endpoint ring buffer from initialization
of the buffer, and initialization of endpoint context parts from
from the rest of the contexts.
It allows driver to clear up and reinitialize endpoint rings
after disconnect without reallocating everything.
This is a prerequisite for the next patch that prevents the transfer
ring from filling up with cancelled (no-op) TRBs if a debug cable is
reconnected several times without transferring anything.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Partially revert commit e1db856bd2 ("usb: xhci: remove '0' write to
write-1-to-clear register") because the patch cleared the Interrupt Pending
bit during interrupt enabling and disabling. The Interrupt Pending bit
should only be cleared when the driver has handled the interrupt.
Ideally, all interrupts should be handled before disabling the interrupt;
consequently, no interrupt should be pending when enabling the interrupt.
For this reason, keep the debug message informing if an interrupt is still
pending when an interrupt is disabled.
Because the Interrupt Pending bit is write-1-to-clear, writing '0' to it
ensures that the state does not change.
Link: https://lore.kernel.org/linux-usb/20250818231103.672ec7ed@foxbook
Fixes: e1db856bd2 ("usb: xhci: remove '0' write to write-1-to-clear register")
Closes: https://bbs.archlinux.org/viewtopic.php?id=307641
cc: stable@vger.kernel.org # 6.16+
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC controller may immediately reuse a slot_id after it's disabled,
giving it to a new enumerating device before the xhci driver freed
all resources related to the disabled device.
In such a scenario, device-A with slot_id equal to 1 is disconnecting
while device-B is enumerating, device-B will fail to enumerate in the
follow sequence.
1.[device-A] send disable slot command
2.[device-B] send enable slot command
3.[device-A] disable slot command completed and wakeup waiting thread
4.[device-B] enable slot command completed with slot_id equal to 1 and
wakeup waiting thread
5.[device-B] driver checks that slot_id is still in use (by device-A) in
xhci_alloc_virt_device, and fail to enumerate due to this
conflict
6.[device-A] xhci->devs[slot_id] set to NULL in xhci_free_virt_device
To fix driver's slot_id resources conflict, clear xhci->devs[slot_id] and
xhci->dcbba->dev_context_ptrs[slot_id] pointers in the interrupt context
when disable slot command completes successfully. Simultaneously, adjust
function xhci_free_virt_device to accurately handle device release.
[minor smatch warning and commit message fix -Mathias]
Cc: stable@vger.kernel.org
Fixes: 7faac1953e ("xhci: avoid race between disable slot command and host runtime suspend")
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250819125844.2042452-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fusb302 irq handler has been carefully optimized by Hans de Goede in
commit 207338ec5a ("usb: typec: fusb302: Improve suspend/resume
handling"). A recent 'fix' undid most of that work to avoid a virtio-gpio
driver bug.
This reverts the incorrect fix, since it is of very low quality. It
reverts the quirks from Hans change (and thus reintroduces the problems
fixed by Hans) while keeping the overhead from the original change.
The proper fix to support using fusb302 with an interrupt line provided
by virtio-gpio must be implemented in the virtio driver instead, which
should support disabling the IRQ from the fusb302 interrupt routine.
Cc: Hans de Goede <hansg@kernel.org>
Cc: Yongbo Zhang <giraffesnn123@gmail.com>
Fixes: 1c2d81bded ("usb: typec: fusb302: fix scheduling while atomic when using virtio-gpio")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250818-fusb302-unthreaded-irq-v1-1-3a9a11a9f56f@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kerneldoc added for usb_hcd_giveback_urb() by commit 41631d3616
("usb: core: Replace in_interrupt() in comments") is unclear and
incorrect. Update the text for greater clarity and to say that URBs
for a root hub will always use a BH context for their completion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/41eaae05-116a-4568-940c-eeb94ab6baa0@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Presently in `max_contaminant_is_contaminant()` if there's no
contaminant detected previously, CC is open & stopped toggling and no
contaminant is currently present, TCPC.RC would be programmed to do DRP
toggling. However, it didn't actively look for a connection. This would
lead to Type-C not detect *any* new connections. Hence, in the above
situation, re-enable toggling & program TCPC to look for a new
connection.
Also, return early if TCPC was looking for connection as this indicates
TCPC has neither detected a potential connection nor a change in
contaminant state.
In addition, once dry detection is complete (port is dry), restart
toggling.
Fixes: 02b332a063 ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250815-fix-upstream-contaminant-v2-2-6c8d6c3adafb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Low power mode is enabled when reading CC resistance as part of
`max_contaminant_read_resistance_kohm()` and left in that state.
However, it's supposed to work with 1uA current source. To read CC
comparator values current source is changed to 80uA. This causes a storm
of CC interrupts as it (falsely) detects a potential contaminant. To
prevent this, disable low power mode current sourcing before reading
comparator values.
Fixes: 02b332a063 ("usb: typec: maxim_contaminant: Implement check_contaminant callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Rule: add
Link: https://lore.kernel.org/stable/20250814-fix-upstream-contaminant-v1-1-801ce8089031%40google.com
Link: https://lore.kernel.org/r/20250815-fix-upstream-contaminant-v2-1-6c8d6c3adafb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses a rarely observed endpoint command timeout
which causes kernel panic due to warn when 'panic_on_warn' is enabled
and unnecessary call trace prints when 'panic_on_warn' is disabled.
It is seen during fast software-controlled connect/disconnect testcases.
The following is one such endpoint command timeout that we observed:
1. Connect
=======
->dwc3_thread_interrupt
->dwc3_ep0_interrupt
->configfs_composite_setup
->composite_setup
->usb_ep_queue
->dwc3_gadget_ep0_queue
->__dwc3_gadget_ep0_queue
->__dwc3_ep0_do_control_data
->dwc3_send_gadget_ep_cmd
2. Disconnect
==========
->dwc3_thread_interrupt
->dwc3_gadget_disconnect_interrupt
->dwc3_ep0_reset_state
->dwc3_ep0_end_control_data
->dwc3_send_gadget_ep_cmd
In the issue scenario, in Exynos platforms, we observed that control
transfers for the previous connect have not yet been completed and end
transfer command sent as a part of the disconnect sequence and
processing of USB_ENDPOINT_HALT feature request from the host timeout.
This maybe an expected scenario since the controller is processing EP
commands sent as a part of the previous connect. It maybe better to
remove WARN_ON in all places where device endpoint commands are sent to
avoid unnecessary kernel panic due to warn.
Cc: stable <stable@kernel.org>
Co-developed-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Akash M <akash.m5@samsung.com>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250808125315.1607-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many Realtek USB Wi-Fi dongles released in recent years have two modes:
one is driver CD mode which has Windows driver onboard, another one is
Wi-Fi mode. Add the US_FL_IGNORE_DEVICE quirk for these multi-mode devices.
Otherwise, usb_modeswitch may fail to switch them to Wi-Fi mode.
Currently there are only two USB IDs known to be used by these multi-mode
Wi-Fi dongles: 0bda:1a2b and 0bda:a192.
Information about Mercury MW310UH in /sys/kernel/debug/usb/devices.
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 12 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=a192 Rev= 2.00
S: Manufacturer=Realtek
S: Product=DISK
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Information about D-Link AX9U rev. A1 in /sys/kernel/debug/usb/devices.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 55 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=1a2b Rev= 0.00
S: Manufacturer=Realtek
S: Product=DISK
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable <stable@kernel.org>
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250813162415.2630-1-zenmchen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 'bcs->Residue' has the data type '__le32', convert it to the
correct byte order of the CPU using this driver when assigning it to
the local variable 'residue'.
Cc: stable <stable@kernel.org>
Fixes: 50a6cb932d ("USB: usb_storage: add ums-realtek driver")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://lore.kernel.org/r/20250813145247.184717-3-thorsten.blum@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When add workaround for ERR051725, the usbmisc will put PHY to
Non-driving mode (OPMODE = 01) after stopping the device controller
and put PHY back to Normal mode (OPMODE = 00) after starting the device
controller.
However, this will bring issue for host controller. Because the PHY may
stay in Non-driving mode after switching the role from device to host.
Then the port will not work if USB device is attached. To fix this issue,
improving the workaround by putting PHY to Non-driving mode for a certain
period and back to Normal mode finally. To make host detect a disconnect
signal, the period should be at least 125us (a micro-frame time) for
high-speed link.
And only working as high-speed mode will need workaround for ERR051725.
So this will also filter the pullup event for high-speed.
Fixes: 11992b4100 ("usb: chipidea: imx: implement workaround for ERR051725")
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250811100833.862876-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kcov_remote_start_usb_softirq() the begin of urb's completion callback.
HCDs marked HCD_BH will invoke this function from the softirq and
in_serving_softirq() will detect this properly.
Root-HUB (RH) requests will not be delayed to softirq but complete
immediately in IRQ context.
This will confuse kcov because in_serving_softirq() will report true if
the softirq is served after the hardirq and if the softirq got
interrupted by the hardirq in which currently runs.
This was addressed by simply disabling interrupts in
kcov_remote_start_usb_softirq() which avoided the interruption by the RH
while a regular completion callback was invoked.
This not only changes the behaviour while kconv is enabled but also
breaks PREEMPT_RT because now sleeping locks can no longer be acquired.
Revert the previous fix. Address the issue by invoking
kcov_remote_start_usb() only if the context is just "serving softirqs"
which is identified by checking in_serving_softirq() and in_hardirq()
must be false.
Fixes: f85d39dd7e ("kcov, usb: disable interrupts in kcov_remote_start_usb_softirq")
Cc: stable <stable@kernel.org>
Reported-by: Yunseong Kim <ysk@kzalloc.com>
Closes: https://lore.kernel.org/all/20250725201400.1078395-2-ysk@kzalloc.com/
Tested-by: Yunseong Kim <ysk@kzalloc.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250811082745.ycJqBXMs@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a device-initiated disconnect, the End Transfer command resets
the event filter, allowing a new xferNotReady event to be generated
before the controller is fully halted. Processing this late event
incorrectly triggers a Start Transfer, which prevents the controller
from halting and results in a DSTS.DEVCTLHLT bit polling timeout.
Ignore the late xferNotReady event if the controller is already in a
disconnected state.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250807090700.2397190-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core will unmap urb->transfer_dma after SETUP stage completes.
Then the USB controller will access unmapped memory when it received
device descriptor. If iommu is equipped, the entire test can't be
completed due to the memory accessing is blocked.
Fix it by calling map_urb_for_dma() again for IN stage. To reduce
redundant map for urb->transfer_buffer, this will also set
URB_NO_TRANSFER_DMA_MAP flag before first map_urb_for_dma() to skip
dma map for urb->transfer_buffer and clear URB_NO_TRANSFER_DMA_MAP
flag before second map_urb_for_dma().
Fixes: 216e0e563d ("usb: core: hcd: use map_urb_for_dma for single step set feature urb")
Cc: stable <stable@kernel.org>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250806083955.3325299-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase the External ROM access timeouts to prevent failures during
programming of External SPI EEPROM chips. The current timeouts are
too short for some SPI EEPROMs used with uPD720201 controllers.
The current timeout for Chip Erase in renesas_rom_erase() is 100 ms ,
the current timeout for Sector Erase issued by the controller before
Page Program in renesas_fw_download_image() is also 100 ms. Neither
timeout is sufficient for e.g. the Macronix MX25L5121E or MX25V5126F.
MX25L5121E reference manual [1] page 35 section "ERASE AND PROGRAMMING
PERFORMANCE" and page 23 section "Table 8. AC CHARACTERISTICS (Temperature
= 0°C to 70°C for Commercial grade, VCC = 2.7V ~ 3.6V)" row "tCE" indicate
that the maximum time required for Chip Erase opcode to complete is 2 s,
and for Sector Erase it is 300 ms .
MX25V5126F reference manual [2] page 47 section "13. ERASE AND PROGRAMMING
PERFORMANCE (2.3V - 3.6V)" and page 42 section "Table 8. AC CHARACTERISTICS
(Temperature = -40°C to 85°C for Industrial grade, VCC = 2.3V - 3.6V)" row
"tCE" indicate that the maximum time required for Chip Erase opcode to
complete is 3.2 s, and for Sector Erase it is 400 ms .
Update the timeouts such, that Chip Erase timeout is set to 5 seconds,
and Sector Erase timeout is set to 500 ms. Such lengthy timeouts ought
to be sufficient for majority of SPI EEPROM chips.
[1] https://www.macronix.com/Lists/Datasheet/Attachments/8634/MX25L5121E,%203V,%20512Kb,%20v1.3.pdf
[2] https://www.macronix.com/Lists/Datasheet/Attachments/8750/MX25V5126F,%202.5V,%20512Kb,%20v1.1.pdf
Fixes: 2478be82de ("usb: renesas-xhci: Add ROM loader for uPD720201")
Cc: stable <stable@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20250802225526.25431-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon resume from system suspend, the PM runtime core issues the
following warning:
tegra-xudc 3550000.usb: Runtime PM usage count underflow!
This is because tegra_xudc_resume() unconditionally calls
schedule_work(&xudc->usb_role_sw_work) whether or not anything has
changed, which causes tegra_xudc_device_mode_off() to be called
even when we're already in that mode.
Keep track of the current state of "device_mode", and only schedule
this work if it has changed from the hardware state on resume.
Signed-off-by: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1uhtkH-007KDZ-JT@rmk-PC.armlinux.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another SanDisk 3.2Gen1 Flash Drive also need DELAY_INIT quick,
or it will randomly work incorrectly on Huawei hisi platforms
when doing reboot test.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250801082728.469406-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
- DEBUGFS
- Remove unneeded debugfs_file_{get,put}() instances
- Remove last remnants of debugfs_real_fops()
- Allow storing non-const void * in struct debugfs_inode_info::aux
- SYSFS
- Switch back to attribute_group::bin_attrs (treewide)
- Switch back to bin_attribute::read()/write() (treewide)
- Constify internal references to 'struct bin_attribute'
- Support cache-ids for device-tree systems
- Add arch hook arch_compact_of_hwid()
- Use arch_compact_of_hwid() to compact MPIDR values on arm64
- Rust
- Device
- Introduce CoreInternal device context (for bus internal methods)
- Provide generic drvdata accessors for bus devices
- Provide Driver::unbind() callbacks
- Use the infrastructure above for auxiliary, PCI and platform
- Implement Device::as_bound()
- Rename Device::as_ref() to Device::from_raw() (treewide)
- Implement fwnode and device property abstractions
- Implement example usage in the Rust platform sample driver
- Devres
- Remove the inner reference count (Arc) and use pin-init instead
- Replace Devres::new_foreign_owned() with devres::register()
- Require T to be Send in Devres<T>
- Initialize the data kept inside a Devres last
- Provide an accessor for the Devres associated Device
- Device ID
- Add support for ACPI device IDs and driver match tables
- Split up generic device ID infrastructure
- Use generic device ID infrastructure in net::phy
- DMA
- Implement the dma::Device trait
- Add DMA mask accessors to dma::Device
- Implement dma::Device for PCI and platform devices
- Use DMA masks from the DMA sample module
- I/O
- Implement abstraction for resource regions (struct resource)
- Implement resource-based ioremap() abstractions
- Provide platform device accessors for I/O (remap) requests
- Misc
- Support fallible PinInit types in Revocable
- Implement Wrapper<T> for Opaque<T>
- Merge pin-init blanket dependencies (for Devres)
- Misc
- Fix OF node leak in auxiliary_device_create()
- Use util macros in device property iterators
- Improve kobject sample code
- Add device_link_test() for testing device link flags
- Fix typo in Documentation/ABI/testing/sysfs-kernel-address_bits
- Hint to prefer container_of_const() over container_of()
-----BEGIN PGP SIGNATURE-----
iHQEABYKAB0WIQS2q/xV6QjXAdC7k+1FlHeO1qrKLgUCaIjkhwAKCRBFlHeO1qrK
LpXuAP9RWwfD9ZGgQZ9OsMk/0pZ2mDclaK97jcmI9TAeSxeZMgD1FHnOMTY7oSIi
iG7Muq0yLD+A5gk9HUnMUnFNrngWCg==
=jgRj
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"debugfs:
- Remove unneeded debugfs_file_{get,put}() instances
- Remove last remnants of debugfs_real_fops()
- Allow storing non-const void * in struct debugfs_inode_info::aux
sysfs:
- Switch back to attribute_group::bin_attrs (treewide)
- Switch back to bin_attribute::read()/write() (treewide)
- Constify internal references to 'struct bin_attribute'
Support cache-ids for device-tree systems:
- Add arch hook arch_compact_of_hwid()
- Use arch_compact_of_hwid() to compact MPIDR values on arm64
Rust:
- Device:
- Introduce CoreInternal device context (for bus internal methods)
- Provide generic drvdata accessors for bus devices
- Provide Driver::unbind() callbacks
- Use the infrastructure above for auxiliary, PCI and platform
- Implement Device::as_bound()
- Rename Device::as_ref() to Device::from_raw() (treewide)
- Implement fwnode and device property abstractions
- Implement example usage in the Rust platform sample driver
- Devres:
- Remove the inner reference count (Arc) and use pin-init instead
- Replace Devres::new_foreign_owned() with devres::register()
- Require T to be Send in Devres<T>
- Initialize the data kept inside a Devres last
- Provide an accessor for the Devres associated Device
- Device ID:
- Add support for ACPI device IDs and driver match tables
- Split up generic device ID infrastructure
- Use generic device ID infrastructure in net::phy
- DMA:
- Implement the dma::Device trait
- Add DMA mask accessors to dma::Device
- Implement dma::Device for PCI and platform devices
- Use DMA masks from the DMA sample module
- I/O:
- Implement abstraction for resource regions (struct resource)
- Implement resource-based ioremap() abstractions
- Provide platform device accessors for I/O (remap) requests
- Misc:
- Support fallible PinInit types in Revocable
- Implement Wrapper<T> for Opaque<T>
- Merge pin-init blanket dependencies (for Devres)
Misc:
- Fix OF node leak in auxiliary_device_create()
- Use util macros in device property iterators
- Improve kobject sample code
- Add device_link_test() for testing device link flags
- Fix typo in Documentation/ABI/testing/sysfs-kernel-address_bits
- Hint to prefer container_of_const() over container_of()"
* tag 'driver-core-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core: (84 commits)
rust: io: fix broken intra-doc links to `platform::Device`
rust: io: fix broken intra-doc link to missing `flags` module
rust: io: mem: enable IoRequest doc-tests
rust: platform: add resource accessors
rust: io: mem: add a generic iomem abstraction
rust: io: add resource abstraction
rust: samples: dma: set DMA mask
rust: platform: implement the `dma::Device` trait
rust: pci: implement the `dma::Device` trait
rust: dma: add DMA addressing capabilities
rust: dma: implement `dma::Device` trait
rust: net::phy Change module_phy_driver macro to use module_device_table macro
rust: net::phy represent DeviceId as transparent wrapper over mdio_device_id
rust: device_id: split out index support into a separate trait
device: rust: rename Device::as_ref() to Device::from_raw()
arm64: cacheinfo: Provide helper to compress MPIDR value into u32
cacheinfo: Add arch hook to compress CPU h/w id into 32 bits for cache-id
cacheinfo: Set cache 'id' based on DT data
container_of: Document container_of() is not to be used in new code
driver core: auxiliary bus: fix OF node leak
...
Here is the big set of USB and Thunderbolt driver changes for 6.17-rc1.
Lots of little things in here, mostly all small cleanups and updates, no
major new features this development cycle. Stuff included in here is:
- xhci minor tweaks for error handling
- typec minor updates and a driver update
- gadget driver api cleanups
- unused function removals
- unbind memory leak fixes
- a few new device ids added
- a few new devices supported for some drivers
- other minor cleanups and changes
All of these have been in linux-next with no reported issues, with the
leak fixes being in the shortest amount of time, but they are "obviously
correct" :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaIeVLw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn3RACgg394VU3ENwqvkh1iF95fVwVheJYAn08YUeoM
98vPdogv4+kuC3B0TbiM
=7pfy
-----END PGP SIGNATURE-----
Merge tag 'usb-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for
6.17-rc1.
Lots of little things in here, mostly all small cleanups and updates,
no major new features this development cycle. Stuff included in here
is:
- xhci minor tweaks for error handling
- typec minor updates and a driver update
- gadget driver api cleanups
- unused function removals
- unbind memory leak fixes
- a few new device ids added
- a few new devices supported for some drivers
- other minor cleanups and changes
All of these have been in linux-next with no reported issues, with the
leak fixes being in the shortest amount of time, but they are
'obviously correct' :)"
* tag 'usb-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (100 commits)
usb: musb: omap2430: clean up probe error handling
usb: musb: omap2430: fix device leak at unbind
usb: gadget: udc: renesas_usb3: fix device leak at unbind
usb: dwc3: meson-g12a: fix device leaks at unbind
usb: dwc3: imx8mp: fix device leak at unbind
usb: musb: omap2430: enable compile testing
usb: gadget: udc: renesas_usb3: drop unused module alias
usb: xhci: print xhci->xhc_state when queue_command failed
usb: atm: cxacru: Merge cxacru_upload_firmware() into cxacru_heavy_init()
USB: serial: option: add Foxconn T99W709
usb: core: add urb->sgt parameter description
thunderbolt: Fix copy+paste error in match_service_id()
usb: typec: ucsi: Update power_supply on power role change
usb: typec: ucsi: psy: Set current max to 100mA for BC 1.2 and Default
usb: typec: fusb302: cache PD RX state
usb: typec: ucsi: yoga-c630: add DRM dependency
usb: gadget : fix use-after-free in composite_dev_cleanup()
usb: chipidea: imx: Add a missing blank line
usb: gadget: f_uac1: replace scnprintf() with sysfs_emit()
usb: usblp: clean up assignment inside if conditions
...
Here is the big set of TTY and Serial driver updates for 6.17-rc1.
Included in here is the following types of changes:
- another cleanup round from Jiri for the 8250 serial driver and some
other tty drivers, things are slowly getting better with our apis
thanks to this work. This touched many tty drivers all over the
tree.
- qcom_geni_serial driver update for new platforms and devices
- 8250 quirk handling fixups
- dt serial binding updates for different boards/platforms
- other minor cleanups and fixes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaIeWPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQHgCfR3KXFe7ElzXQqjJhtN/ej6IPijIAoI6k3g0m
4UewNOIef9XpIAJ8zuoo
=850o
-----END PGP SIGNATURE-----
Merge tag 'tty-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 6.17-rc1.
Included in here is the following types of changes:
- another cleanup round from Jiri for the 8250 serial driver and some
other tty drivers, things are slowly getting better with our apis
thanks to this work. This touched many tty drivers all over the
tree.
- qcom_geni_serial driver update for new platforms and devices
- 8250 quirk handling fixups
- dt serial binding updates for different boards/platforms
- other minor cleanups and fixes
All of these have been in linux-next with no reported issues"
* tag 'tty-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
dt-bindings: serial: snps-dw-apb-uart: Allow use of a power-domain
serial: 8250: fix panic due to PSLVERR
dt-bindings: serial: samsung: add samsung,exynos2200-uart compatible
vt: defkeymap: Map keycodes above 127 to K_HOLE
vt: keyboard: Don't process Unicode characters in K_OFF mode
serial: qcom-geni: Enable Serial on SA8255p Qualcomm platforms
serial: qcom-geni: Enable PM runtime for serial driver
serial: qcom-geni: move clock-rate logic to separate function
serial: qcom-geni: move resource control logic to separate functions
serial: qcom-geni: move resource initialization to separate function
soc: qcom: geni-se: Enable QUPs on SA8255p Qualcomm platforms
dt-bindings: qcom: geni-se: describe SA8255p
dt-bindings: serial: describe SA8255p
serial: 8250_dw: Fix typo "notifer"
dt-bindings: serial: 8250: spacemit: set clocks property as required
dt-bindings: serial: renesas: Document RZ/V2N SCIF
serial: 8250_ce4100: Fix CONFIG_SERIAL_8250=n build
tty: omit need_resched() before cond_resched()
serial: 8250_ni: Reorder local variables
serial: 8250_ni: Fix build warning
...
GPIOLIB core:
- introduce a parallel, limited sysfs user ABI that doesn't expose the
global GPIO numbers to user-space while maintaining backward
compatibility with the end goal of it completely replacing the existing
interface, allowing us to remove it
- remove the legacy devm_gpio_request() routine which has no more users
- start the process of allowing to compile-out the legacy parts of the
GPIO core for users who don't need it by introducing a new Kconfig
option: GPIOLIB_LEGACY
- don't use global GPIO numbers in debugfs output from the core code
(drivers still do it, the work is ongoing)
- start the process of moving the fields specific to the gpio-mmio helper
out of the core struct gpio_chip into their own structure that wraps
it: create a new header with modern interfaces and convert several
drivers to using it
- remove the platform data structure associated with the gpio-mmio helper
from the kernel after having converted all remaining users to generic
device properties
- remove legacy struct gpio definition as it has no more users
New drivers:
- add the GPIO driver for the Apple System Management Controller
Driver improvements:
- add support for new models to gpio-adp5585, gpio-tps65219 and
gpio-pca953x
- extend the interrupt support in gpio-loongson-64bit
- allow to mark the simulated GPIO lines as invalid in gpio-sim
- convert all remaining GPIO drivers to using the new GPIO value setter
callbacks
- convert gpio-rcar to using simple device power management ops callbacks
- don't check if current direction of a line is output before setting
the value in gpio-pisosr and ti-fpc202: the GPIO core already handles
that
- also drop unneeded GPIO range checks in drivers, the core already makes
sure we're within bounds when calling driver callbacks
- use dev_fwnode() where applicable across GPIO drivers
- set line value in gpio-zynqmp-modepin and gpio-twl6040 when the user
wants to change direction of the pin to output even though these
drivers don't need to do anything else to actually set the direction,
otherwise a call like gpiod_direction_output(d, 1) will not result in
the line driver high
- remove the reduntant call to pm_runtime_mark_last_busy() from
gpio-arizona
- use lock guards in gpio-cadence and gpio-mxc
- check the return values of regmap functions in gpio-wcd934x and
gpio-tps65912
- use better regmap interfaces in gpio-wcove and gpio-pca953x
- remove dummy GPIO chip callbacks from several drivers in cases where
the GPIO core can already handle their absence
- allow building gpio-palmas as a module
Fixes:
- use correct bit widths (according to the documentation) in gpio-virtio
Device-tree bindings:
- convert several of the legacy .txt documents for many different devices
to YAML, improving automatic validation
- create a "trivial" GPIO DT schema that covers a wide range of simple
hardware that share a set of basic GPIO properties
- document new HW: Apple MAC SMC GPIO block and adp5589 I/O expander
- document a new model for pca95xx
- add and/or remove properties in YAML documents for gpio-rockchip,
fsl,qoriq-gpio, arm,pl061 and gpio-xilinx
Misc:
- some minor refactoring in several places, adding/removing forward
declarations, moving defines to better places, constify the arguments
in some functions, remove duplicate includes, etc.
- documentation updates
-----BEGIN PGP SIGNATURE-----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=tUPm
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There's one new driver (Apple SMC) and extensions to existing drivers
for supporting new HW models. A lot of different impovements across
drivers and in core GPIO code. Details on that are in the signed tag
as usual.
We managed to remove some of the legacy APIs. Arnd Bergmann started to
work on making the legacy bits optional so that we may compile them
only for older platforms that still really need them.
Rob Herring has done a lot of work to convert legacy .txt dt-bindings
for GPIO controllers to YAML. There are only a few left now in the
GPIO tree.
A big part of the commits in this PR concern the conversion of GPIO
drivers to using the new line value setter callbacks. This conversion
is now complete treewide (unless I've missed something) and once all
the changes from different trees land in mainline, I'll send you
another PR containing a commit dropping the legacy callbacks from the
tree.
As the quest to pay back technical dept never really ends, we're
starting another set of interface conversions, this time it's about
moving fields specific to only a handful of drivers using the
gpio-mmio helper out of the core gpio_chip structure that every
controller implements and uses. This cycle we introduce a new set of
APIs and convert a few drivers under drivers/gpio/, next cycle we'll
convert remaining modules treewide (in gpio, pinctrl and mfd trees)
and finally remove the old interfaces and move the gpio-mmio fields
into their own structure wrapping gpio_chip.
One last change I should mention here is the rework of the sysfs
interface. In 2016, we introduced the GPIO character device as the
preferred alternative to the sysfs class under /sys/class/gpio. While
it has seen a wide adoption with the help of its user-space
counterpart - libgpiod - there are still users who prefer the
simplicity of sysfs.
As far as the GPIO subsystem is concerned, the problem is not the
existince of the GPIO class as such but rather the fact that it
exposes the global GPIO numbers to the user-space, stopping us from
ever being able to remove the numberspace from the kernel. To that
end, this release we introduced a parallel, limited sysfs interface
that doesn't expose these numbers and only implements a subset of
features that are relevant to the existing users. This is a result of
several discussions over the course of last year and should allow us
to remove the legacy part some time in the future.
Summary:
GPIOLIB core:
- introduce a parallel, limited sysfs user ABI that doesn't expose
the global GPIO numbers to user-space while maintaining backward
compatibility with the end goal of it completely replacing the
existing interface, allowing us to remove it
- remove the legacy devm_gpio_request() routine which has no more
users
- start the process of allowing to compile-out the legacy parts of
the GPIO core for users who don't need it by introducing a new
Kconfig option: GPIOLIB_LEGACY
- don't use global GPIO numbers in debugfs output from the core code
(drivers still do it, the work is ongoing)
- start the process of moving the fields specific to the gpio-mmio
helper out of the core struct gpio_chip into their own structure
that wraps it: create a new header with modern interfaces and
convert several drivers to using it
- remove the platform data structure associated with the gpio-mmio
helper from the kernel after having converted all remaining users
to generic device properties
- remove legacy struct gpio definition as it has no more users
New drivers:
- add the GPIO driver for the Apple System Management Controller
Driver improvements:
- add support for new models to gpio-adp5585, gpio-tps65219 and
gpio-pca953x
- extend the interrupt support in gpio-loongson-64bit
- allow to mark the simulated GPIO lines as invalid in gpio-sim
- convert all remaining GPIO drivers to using the new GPIO value
setter callbacks
- convert gpio-rcar to using simple device power management ops
callbacks
- don't check if current direction of a line is output before setting
the value in gpio-pisosr and ti-fpc202: the GPIO core already
handles that
- also drop unneeded GPIO range checks in drivers, the core already
makes sure we're within bounds when calling driver callbacks
- use dev_fwnode() where applicable across GPIO drivers
- set line value in gpio-zynqmp-modepin and gpio-twl6040 when the
user wants to change direction of the pin to output even though
these drivers don't need to do anything else to actually set the
direction, otherwise a call like gpiod_direction_output(d, 1) will
not result in the line driver high
- remove the reduntant call to pm_runtime_mark_last_busy() from
gpio-arizona
- use lock guards in gpio-cadence and gpio-mxc
- check the return values of regmap functions in gpio-wcd934x and
gpio-tps65912
- use better regmap interfaces in gpio-wcove and gpio-pca953x
- remove dummy GPIO chip callbacks from several drivers in cases
where the GPIO core can already handle their absence
- allow building gpio-palmas as a module
Fixes:
- use correct bit widths (according to the documentation) in
gpio-virtio
Device-tree bindings:
- convert several of the legacy .txt documents for many different
devices to YAML, improving automatic validation
- create a "trivial" GPIO DT schema that covers a wide range of
simple hardware that share a set of basic GPIO properties
- document new HW: Apple MAC SMC GPIO block and adp5589 I/O expander
- document a new model for pca95xx
- add and/or remove properties in YAML documents for gpio-rockchip,
fsl,qoriq-gpio, arm,pl061 and gpio-xilinx
Misc:
- some minor refactoring in several places, adding/removing forward
declarations, moving defines to better places, constify the
arguments in some functions, remove duplicate includes, etc.
- documentation updates"
* tag 'gpio-updates-for-v6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (202 commits)
MIPS: alchemy: gpio: use new GPIO line value setter callbacks for the remaining chips
gpiolib: enable CONFIG_GPIOLIB_LEGACY even for !GPIOLIB
gpio: virtio: Fix config space reading.
gpiolib: make legacy interfaces optional
dt-bindings: gpio: rockchip: Allow use of a power-domain
gpiolib: of: add forward declaration for struct device_node
power: reset: macsmc-reboot: Add driver for rebooting via Apple SMC
gpio: Add new gpio-macsmc driver for Apple Macs
mfd: Add Apple Silicon System Management Controller
soc: apple: rtkit: Make shmem_destroy optional
dt-bindings: mfd: Add Apple Mac System Management Controller
dt-bindings: power: reboot: Add Apple Mac SMC Reboot Controller
dt-bindings: gpio: Add Apple Mac SMC GPIO block
gpio: cadence: Remove duplicated include in gpio-cadence.c
gpio: tps65219: Add support for TI TPS65214 PMIC
gpio: tps65219: Update _IDX & _OFFSET macro prefix
gpio: sysfs: Fix an end of loop test in gpiod_unexport()
dt-bindings: gpio: Convert qca,ar7100-gpio to DT schema
dt-bindings: gpio: Convert maxim,max3191x to DT schema
dt-bindings: gpio: fsl,qoriq-gpio: Add missing mpc8xxx compatibles
...
places; unfortunately, it's easy to get wrong. A number of open-coded
attempts are out there, with varying amount of bogosities.
simple_recursive_removal() had been introduced for doing that with
all precautions needed; it does an equivalent of rm -rf, with sufficient
locking, eviction of anything mounted on top of the subtree, etc.
This series converts a bunch of open-coded instances to using that.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCaIRCUwAKCRBZ7Krx/gZQ
66XWAP9BNyHcvl9uV/ku/mswYiRBxYoVogciIKeugwYTVLuTJgEA7jdh1eyLkvbS
rwbL7XD+Q35/vXZHEet+RLCGH3ae6wc=
=yaKF
-----END PGP SIGNATURE-----
Merge tag 'pull-simple_recursive_removal' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull simple_recursive_removal() update from Al Viro:
"Removing subtrees of kernel filesystems is done in quite a few places;
unfortunately, it's easy to get wrong. A number of open-coded attempts
are out there, with varying amount of bogosities.
simple_recursive_removal() had been introduced for doing that with all
precautions needed; it does an equivalent of rm -rf, with sufficient
locking, eviction of anything mounted on top of the subtree, etc.
This series converts a bunch of open-coded instances to using that"
* tag 'pull-simple_recursive_removal' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
functionfs, gadgetfs: use simple_recursive_removal()
kill binderfs_remove_file()
fuse_ctl: use simple_recursive_removal()
pstore: switch to locked_recursive_removal()
binfmt_misc: switch to locked_recursive_removal()
spufs: switch to locked_recursive_removal()
add locked_recursive_removal()
better lockdep annotations for simple_recursive_removal()
simple_recursive_removal(): saner interaction with fsnotify
Using numbered error labels is discouraged (e.g. as it requires
renumbering them when adding a new intermediate error path).
Rename the error labels after what they do.
While at it, drop the redundant platform allocation failure dev_err()
as the error would already have been logged by the allocator.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 8934d3e4d0 ("usb: musb: omap2430: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the reference to the companion device taken during
probe when the driver is unbound.
Fixes: 39facfa01c ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Cc: stable@vger.kernel.org # 4.19
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the references taken to the child devices by
of_find_device_by_node() during probe on driver unbind.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Cc: stable@vger.kernel.org # 5.2
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20250724091910.21092-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the reference to the dwc3 device taken by
of_find_device_by_node() on probe errors and on driver unbind.
Fixes: 6dd2565989 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing seems to prevent the driver from being compile tested on
non-OMAP platforms so enable it to provide wider build coverage.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724092104.21317-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
