[ Upstream commit e5cb94ba5f ]
Ben reports that when running with CONFIG_DEBUG_PREEMPT, using
__arch_counter_get_cntvct_stable() results in well deserves warnings,
as we access a per-CPU variable without preemption disabled.
Fix the issue by disabling preemption on reading the counter. We can
probably do a lot better by not disabling preemption on systems that
do not require horrible workarounds to return a valid counter value,
but this plugs the issue for the time being.
Fixes: 29cc0f3aa7 ("arm64: Force the use of CNTVCT_EL0 in __delay()")
Reported-by: Ben Horgan <ben.horgan@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/aZw3EGs4rbQvbAzV@e134344.arm.com
Tested-by: Ben Horgan <ben.horgan@arm.com>
Tested-by: André Draszik <andre.draszik@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29cc0f3aa7 ]
Quentin forwards a report from Hyesoo Yu, describing an interesting
problem with the use of WFxT in __delay() when a vcpu is loaded and
that KVM is *not* in VHE mode (either nVHE or hVHE).
In this case, CNTVOFF_EL2 is set to a non-zero value to reflect the
state of the guest virtual counter. At the same time, __delay() is
using get_cycles() to read the counter value, which is indirected to
reading CNTPCT_EL0.
The core of the issue is that WFxT is using the *virtual* counter,
while the kernel is using the physical counter, and that the offset
introduces a really bad discrepancy between the two.
Fix this by forcing the use of CNTVCT_EL0, making __delay() consistent
irrespective of the value of CNTVOFF_EL2.
Reported-by: Hyesoo Yu <hyesoo.yu@samsung.com>
Reported-by: Quentin Perret <qperret@google.com>
Reviewed-by: Quentin Perret <qperret@google.com>
Fixes: 7d26b0516a ("arm64: Use WFxT for __delay() when possible")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/ktosachvft2cgqd5qkukn275ugmhy6xrhxur4zqpdxlfr3qh5h@o3zrfnsq63od
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb0c99e08a ]
The implementation of __READ_ONCE() under CONFIG_LTO=y incorrectly
qualified the fallback "once" access for types larger than 8 bytes,
which are not atomic but should still happen "once" and suppress common
compiler optimizations.
The cast `volatile typeof(__x)` applied the volatile qualifier to the
pointer type itself rather than the pointee. This created a volatile
pointer to a non-volatile type, which violated __READ_ONCE() semantics.
Fix this by casting to `volatile typeof(*__x) *`.
With a defconfig + LTO + debug options build, we see the following
functions to be affected:
xen_manage_runstate_time (884 -> 944 bytes)
xen_steal_clock (248 -> 340 bytes)
^-- use __READ_ONCE() to load vcpu_runstate_info structs
Fixes: e35123d83e ("arm64: lto: Strengthen READ_ONCE() to acquire when CONFIG_LTO=y")
Cc: stable@vger.kernel.org
Reviewed-by: Boqun Feng <boqun@kernel.org>
Signed-off-by: Marco Elver <elver@google.com>
Tested-by: David Laight <david.laight.linux@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f3b950492 ]
If a process wrote to POR_EL0 and then crashed before a context switch
happened, the coredump would contain an incorrect value for POR_EL0.
The value read in poe_get() would be a stale value left in thread.por_el0. Fix
this by reading the value from the system register, if the target thread is the
current thread.
This matches what gcs/fpsimd do.
Fixes: 1751981992 ("arm64/ptrace: add support for FEAT_POE")
Reported-by: David Spickett <david.spickett@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Kevin Brodsky <kevin.brodsky@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79a3286e61 ]
Rockchip RK3576 UFS controller uses a dedicated pin to reset the connected
UFS device, which can operate either in a hardware controlled mode or as a
GPIO pin.
Power-on default is GPIO mode, but the boot ROM reconfigures it to a
hardware controlled mode if it uses UFS to load the next boot stage.
Given that existing bindings (and rk3576.dtsi) expect a GPIO-controlled
device reset, request the required pin config explicitly.
The pin is requested with pull-down enabled, which is in line with the
SoC power-on default and helps ensure that the attached UFS chip stays
in reset until the driver takes over the control of the respective
GPIO line.
This doesn't appear to affect Linux, but it does affect U-boot:
Before:
=> md.l 0x2604b398
2604b398: 00000011 00000000 00000000 00000000 ................
< ... snip ... >
=> ufs init
ufshcd-rockchip ufshc@2a2d0000: [RX, TX]: gear=[3, 3], lane[2, 2], pwr[FASTAUTO_MODE, FASTAUTO_MODE], rate = 2
=> md.l 0x2604b398
2604b398: 00000011 00000000 00000000 00000000 ................
After:
=> md.l 0x2604b398
2604b398: 00000011 00000000 00000000 00000000 ................
< ... snip ...>
=> ufs init
ufshcd-rockchip ufshc@2a2d0000: [RX, TX]: gear=[3, 3], lane[2, 2], pwr[FASTAUTO_MODE, FASTAUTO_MODE], rate = 2
=> md.l 0x2604b398
2604b398: 00000010 00000000 00000000 00000000 ................
(0x2604b398 is the respective pin mux register, with its BIT0 driving the
mode of UFS_RST: unset = GPIO, set = hardware controlled UFS_RST)
This helps ensure that GPIO-driven device reset actually fires when the
system requests it, not when whatever black box magic inside the UFSHC
decides to reset the flash chip.
Cc: stable@vger.kernel.org
Fixes: c75e5e010f ("scsi: arm64: dts: rockchip: Add UFS support for RK3576 SoC")
Reported-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://patch.msgid.link/20260121-ufs-rst-v3-1-35839bcb4ca7@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eb80a2eee ]
We had extended the sysreg masking infrastructure to more general
registers, instead of restricting it to VNCR-backed registers, since
commit a016202009 ("KVM: arm64: Extend masking facility to arbitrary
registers"). Fix kvm_get_sysreg_res0() to reflect this fact.
Note that we're sure that we only deal with FGT registers in
kvm_get_sysreg_res0(), the
if (sr < __VNCR_START__)
is actually a never false, which should probably be removed later.
Fixes: 69c19e047d ("KVM: arm64: Add TCR2_EL2 to the sysreg arrays")
Signed-off-by: Zenghui Yu (Huawei) <zenghui.yu@linux.dev>
Link: https://patch.msgid.link/20260121101631.41037-1-zenghui.yu@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7226664bf9 ]
When runtime suspend is enabled, the associated power domain is powered
off, which resets the registers, including the power control bit. As a result,
the card loses power during runtime suspend. The card should still be able
to process I/O with the help of mmc_blk_mq_rw_recovery(), which is suboptimal.
To address this issue, we must use vmmc-supply with a GPIO based method to
maintain power to the card. Also, add cd-gpios method to make hot-plug work
correctly during idle periods.
Fixes: f135a1a073 ("arm64: dts: rockchip: Add rk3576 evb1 board")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/1768524932-163929-5-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e4e729325 ]
Add the display controller and DPTX phy power-domains to the framebuffer
node to keep the framebuffer and display out working after device probing
finished.
The OS has more control about the display pipeline used for the HDMI
output on M2 based devices. The HDMI output is driven by an integrated
DisplayPort to HDMI converter (Parade PS190). The DPTX phy is now
controlled by the OS and no longer by firmware running on the display
co-processor. This allows using the second display controller on the
second USB type-c port or tunneling 2 DisplayPort connections over
USB4/Thunderbolt.
The m1n1 bootloader uses the second display controller to drive the HDMI
output. Adjust for this difference compared to the notebooks as well.
Fixes: 2d5ce3fbef ("arm64: dts: apple: t8112: Initial t8112 (M2) device trees")
Cc: stable@vger.kernel.org
Signed-off-by: Janne Grunau <j@jannau.net>
Link: https://patch.msgid.link/20260108-apple-dt-pmgr-fixes-v1-1-cfdce629c0a8@jannau.net
Signed-off-by: Sven Peter <sven@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f22c81bebf ]
The arm64 kernel doesn't boot with annotated branches
(PROFILE_ANNOTATED_BRANCHES) enabled and CONFIG_DEBUG_VIRTUAL together.
Bisecting it, I found that disabling branch profiling in arch/arm64/mm
solved the problem. Narrowing down a bit further, I found that
physaddr.c is the file that needs to have branch profiling disabled to
get the machine to boot.
I suspect that it might invoke some ftrace helper very early in the boot
process and ftrace is still not enabled(!?).
Rather than playing whack-a-mole with individual files, disable branch
profiling for the entire arch/arm64 tree, similar to what x86 already
does in arch/x86/Kbuild.
Cc: stable@vger.kernel.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c6192ec9c ]
Bindings always required "qcom,num-ees" and "num-channels" properties,
as reported by dtbs_check:
sm8750-mtp.dtb: dma-controller@1dc4000 (qcom,bam-v1.7.4): 'anyOf' conditional failed, one must be fixed:
'qcom,powered-remotely' is a required property
'num-channels' is a required property
'qcom,num-ees' is a required property
'clocks' is a required property
'clock-names' is a required property
However since commit 5068b52548 ("dmaengine: qcom: bam_dma: Fix DT
error handling for num-channels/ees") missing properties are actually
fatal and BAM does not probe:
bam-dma-engine 1dc4000.dma-controller: num-channels unspecified in dt
bam-dma-engine 1dc4000.dma-controller: probe with driver bam-dma-engine failed with error -22
Fixes: eeb0f3e4ea ("arm64: dts: qcom: sm8750: Add QCrypto nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251229115734.205744-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0907cab01f ]
The DP PHYs on X1E80100 need the ref clock which is provided by the
TCSR CC.
The current X Elite devices supported upstream work fine without this
clock, because the boot firmware leaves this clock enabled. But we should
not rely on that. Also, even though this change breaks the ABI, it is
needed in order to make the driver disables this clock along with the
other ones, for a proper bring-down of the entire PHY.
So lets attach it to each of the DP PHYs in order to do that.
Cc: stable@vger.kernel.org # v6.9
Fixes: 1940c25eaa ("arm64: dts: qcom: x1e80100: Add display nodes")
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20251224-phy-qcom-edp-add-missing-refclk-v5-3-3f45d349b5ac@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c1d1591f8 ]
If the OS does not support recovering the state left by the
bootloader it needs a way to reset display hardware, so that it can
start from a clean state. Add a reference to the relevant reset.
It fixes display init issue appeared in Linux v6.17: without reset
device boots into black screen and you need to turn display off/on
to "fix" it. Also sometimes it can boot into solid blue color
with these messages in kernel log:
hw recovery is not complete for ctl:2
[drm:dpu_encoder_phys_vid_prepare_for_kickoff:569] [dpu error]enc33
intf1 ctl 2 reset failure: -22
[drm:dpu_encoder_frame_done_timeout:2727] [dpu error]enc33 frame
done timeout
Fixes: 0e789b491b ("pmdomain: core: Leave powered-on genpds on until sync_state")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251116-sdm660-mdss-reset-v2-3-6219bec0a97f@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de86dbc0fb ]
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: 87f95ea316 ("arm64: dts: ti: Add Toradex Verdin AM62P")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20251209084126.33282-1-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 729a2e8e9a ]
gcc-16 warns about an instance that older compilers did not:
arch/arm64/mm/hugetlbpage.c: In function 'huge_pte_clear':
arch/arm64/mm/hugetlbpage.c:369:57: error: parameter 'addr' set but not used [-Werror=unused-but-set-parameter=]
The issue here is that __pte_clear() does not actually use its second
argument, but when CONFIG_ARM64_CONTPTE is enabled it still gets
updated.
Replace the macro with an inline function to let the compiler see
the argument getting passed down.
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dev Jain <dev.jain@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfa93788dd ]
The USB2 port on Smaug is configured for OTG operation but lacked the
required 'usb-role-switch' property, leading to a failed probe and a
non-functioning USB port. Add the property along with setting the default
role to host.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c197179990 ]
This reverts commit 06d22ed6b6.
OP-TEE logic in U-Boot automatically injects a reserved-memory
node along with optee firmware node to kernel device tree.
The injection logic is dependent on that there is no manually
defined optee node. Having the node in zynqmp.dtsi effectively
breaks OP-TEE's insertion of the reserved-memory node, causing
memory access violations during runtime.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20251125-revert-zynqmp-optee-v1-1-d2ce4c0fcaf6@vaisala.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3baa5d4b3 ]
The TSV110 processor is vulnerable to the Spectre-BHB (Branch History
Buffer) attack, which can be exploited to leak information through
branch prediction side channels. This commit adds the MIDR of TSV110
to the list for software mitigation.
Signed-off-by: Jinqian Yang <yangjinqian1@huawei.com>
Reviewed-by: Zenghui Yu <zenghui.yu@linux.dev>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd6735896d ]
bpf_address_lookup() has been used only in kallsyms_lookup_buildid(). It
was supposed to set @modname and @modbuildid when the symbol was in a
module.
But it always just cleared @modname because BPF symbols were never in a
module. And it did not clear @modbuildid because the pointer was not
passed.
The wrapper is no longer needed. Both @modname and @modbuildid are now
always initialized to NULL in kallsyms_lookup_buildid().
Remove the wrapper and rename __bpf_address_lookup() to
bpf_address_lookup() because this variant is used everywhere.
[akpm@linux-foundation.org: fix loongarch]
Link: https://lkml.kernel.org/r/20251128135920.217303-6-pmladek@suse.com
Fixes: 9294523e37 ("module: add printk formats to add module build ID to stacktraces")
Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Aaron Tomlin <atomlin@atomlin.com>
Cc: Daniel Borkman <daniel@iogearbox.net>
Cc: Daniel Gomez <da.gomez@samsung.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Kees Cook <kees@kernel.org>
Cc: Luis Chamberalin <mcgrof@kernel.org>
Cc: Marc Rutland <mark.rutland@arm.com>
Cc: "Masami Hiramatsu (Google)" <mhiramat@kernel.org>
Cc: Petr Pavlu <petr.pavlu@suse.com>
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dda4bdd325 ]
QUP devices are currently marked with opp-shared in their OPP table,
causing the kernel to treat them as part of a shared OPP domain. This
leads to the qcom_geni_serial driver failing to probe with error
-EBUSY (-16).
Remove the opp-shared property to ensure the OPP framework treats the
QUP OPP table as device-specific, allowing the serial driver to probe
successfully
Fixes: f6746dc9e3 ("arm64: dts: qcom: qcs615: Add QUPv3 configuration")
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251111170350.525832-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38dd256e1 ]
Unlike the phone SoCs this was copied from, x1e has a 40-bit physical bus.
The upper address space is used to support more than 32GB of memory.
This fixes issues when DMA buffers are allocated outside the 36-bit range.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251127212943.24480-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bfb696ccd ]
On SDM845 SPI uses hardware-provided chip select, while specifying
cs-gpio makes the driver request GPIO pin, which on DB845c conflicts
with the normal host controllers pinctrl entry.
Drop the cs-gpios property to restore SPI functionality.
Fixes: cb29e7106d ("arm64: dts: qcom: db845c: Add support for MCP2517FD")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-7-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5dc4812f6 ]
Follow commit 9c92d36b0b ("arm64: dts: qcom: qrb2210-rb1: Fix UART3
wakeup IRQ storm") and apply the similar fix to the RB2 platform.
Having RX / TX pins as pull up and wakup interrupt as high-level
triggered generates an interrupt storm when trying to suspend the
device. Avoid the storm by using the falling edge trigger (as all other
platforms do).
Fixes: cab60b1665 ("arm64: dts: qcom: qrb4210-rb2: Enable bluetooth")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-6-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c941feaa3 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clock to make sure it is properly configured
Fixes: 8a6b3ca2d3 ("arm64: dts: meson: g12a: add SDIO controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-6-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be2ff5fdb0 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clocks to make sure they are properly configured
Fixes: 4759fd87b9 ("arm64: dts: meson: g12a: add mmc nodes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-5-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4067065590 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clocks to make sure they are properly configured
Fixes: 50662499f9 ("ARM64: dts: meson-gx: Use correct mmc clock source 0")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-4-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13d3fe2318 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clocks to make sure they are properly configured
Fixes: 221cf34bac ("ARM64: dts: meson-axg: enable the eMMC controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-3-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69330fd236 ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
Assign the clocks to make sure they are properly configured
Fixes: 520b792e83 ("arm64: dts: amlogic: add some device nodes for C3")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-1-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61acc4428a ]
Each A72 core has one watchdog instance associated with it. Since j742s2
has 4 A72 cores, the common file should not define 8 watchdog instances.
Refactor the last 4 extra watchdogs from the common file to j784s4
specific file, as j784s4 has 8 A72 cores and thus hardware description
requires 8 watchdog instances.
Fixes: 9cc161a450 ("arm64: dts: ti: Refactor J784s4 SoC files to a common file")
Signed-off-by: Abhash Kumar Jha <a-kumar2@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://patch.msgid.link/20260112085113.3476193-3-a-kumar2@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24c9d5fb8b ]
The device tree nodes should be ordered by unit addresses in ascending
order.
Correct the order by moving the c71_3 DSP node at the end as it has a
higher unit address.
Signed-off-by: Abhash Kumar Jha <a-kumar2@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://patch.msgid.link/20260112085113.3476193-2-a-kumar2@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: 61acc4428a ("arm64: dts: ti: k3-j784s4-j742s2-main-common.dtsi: Refactor watchdog instances for j784s4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a115d4292 ]
MMC A and C are mis-represented as having their "clkin0" input connected to
xtal while it is actually connected to the MMC clock, probably in an
attempt to provide 24MHz to the device on this input.
Fix this and assign the clock to 24MHz to actually provide the required
rate.
Fixes: 3ab9d54b5d ("arm64: dts: amlogic: enable some device nodes for S4")
Tested-by: Nick Xie <nick@khadas.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-s4-mmc-fixup-v3-2-a4d3e136b3f2@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86124a8bec ]
The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.
This assumption did hold true until but it now, but it is apparently
not the case with s4. The clock has been reported to provide 1GHz
instead. This is most likely due to how the bootloader is using the MMC
clock on this platform.
Regardless of why the MMC clock rate is 1GHz, if the MMC driver expects
24MHz, the clock should be properly assigned, so assign it.
Reported-by: Nick Xie <nick@khadas.com>
Closes: https://lore.kernel.org/linux-amlogic/20260113011931.40424-1-nick@khadas.com/
Fixes: 3ab9d54b5d ("arm64: dts: amlogic: enable some device nodes for S4")
Tested-by: Nick Xie <nick@khadas.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-s4-mmc-fixup-v3-1-a4d3e136b3f2@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1b1ee0348 ]
Switch SD0 write-protect detection to a GPIO on the RZ/T2H and RZ/N2H
EVKs. Both boards use a full-size SD card slot on the SD0 channel with
a dedicated WP pin.
The RZ/T2H and RZ/N2H SoCs use of_data_rcar_gen3, which sets
MMC_CAP2_NO_WRITE_PROTECT and causes the core to ignore the WP signal
unless a wp-gpios property is provided. Describe the WP pin as a GPIO
to allow the MMC core to evaluate the write-protect status correctly.
Fixes: d065453e5e ("arm64: dts: renesas: rzt2h-rzn2h-evk: Enable SD card slot")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260106131319.643084-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db5fbe508 ]
Trivial change, Analog Devices vendor prefix is "adi", but there is
a valid "ad" vendor prefix of another company, this may explain why
the issue hasn't been discovered by the automatic tests.
A problem of not described compatible value is out of this change scope.
Fixes: c636eeb751 ("arm64: dts: qcom: msm8994-octagon: Add AD7147 and APDS9930 sensors")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251226003923.3341904-1-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3af51501e2 ]
It seems the USB combo SS1 and SS2 ref clocks have another gate, unlike
the SS0. These gates are part of the TCSR clock controller.
At least on Dell XPS 13 (9345), if the ref clock provided by the TCSR
clock controller for SS1 PHY is disabled on the clk_disable_unused late
initcall, the PHY fails to initialize. It doesn't happen on the SS0 PHY
and the SS2 is not used on this device.
This doesn't seem to be a problem on CRD though. It might be that the
RPMh has a vote for it from some other consumer and does not actually
disable it when ther kernel drops its vote.
Either way, these TCSR provided clocks seem to be the correct ones for
the SS1 and SS2, so use them instead.
Fixes: 4af46b7bd6 ("arm64: dts: qcom: x1e80100: Add USB nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251103-dts-qcom-x1e80100-fix-combo-ref-clks-v1-1-f395ec3cb7e8@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad33ee060b ]
This regulator is used only for the display, which is enabled by the
bootloader and left on for continuous splash. Mark it as such.
Fixes: 288ef8a426 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251118-dts-oneplus-regulators-v2-3-3e67cea1e4e7@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9b98b9dad ]
The touchscreen isn't enabled by bootloader and doesn't need to be
enabled at boot, only when the driver probes, thus remove the
regulator-boot-on property.
Fixes: 288ef8a426 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251118-dts-oneplus-regulators-v2-1-3e67cea1e4e7@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e814796dfc ]
Historically sdm630.dtsi has used 1 byte length for the gpu_speed_bin
cell, although it spans two bytes (offset 5, size 7 bits). It was being
accepted by the kernel because before the commit 7a06ef7510 ("nvmem:
core: fix bit offsets of more than one byte") the kernel didn't have
length check. After this commit nvmem core rejects QFPROM on sdm630 /
sdm660, making GPU and USB unusable on those platforms.
Set the size of the gpu_speed_bin cell to 2 bytes, fixing the parsing
error. While we are at it, update the length to 8 bits as pointed out by
Alexey Minnekhanov.
Fixes: b190fb0106 ("arm64: dts: qcom: sdm630: Add sdm630 dts file")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Link: https://lore.kernel.org/r/20251211-sdm630-fix-gpu-v2-1-92f0e736dba0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53a5c1d98d ]
As per datasheet of the HDMI protection IC the CEC_IC pin has been
configured as open-drain.
Fixes: ddabb3ce3f ("arm64: dts: freescale: add TQMa8MPQL on MBa8MP-RAS314")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8401527abb ]
As per datasheet of the HDMI protection IC the CEC_IC pin has been
configured as open-drain.
Fixes: 418d1d840e ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53c998527f ]
alloc_gcs() returns an error-encoded pointer on failure, which comes
from do_mmap(), not NULL.
The current NULL check fails to detect errors, which could lead to using
an invalid GCS address.
Use IS_ERR_VALUE() to properly detect errors, consistent with the
check in gcs_alloc_thread_stack().
Fixes: b57180c75c ("arm64/gcs: Implement shadow stack prctl() interface")
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit be0b304eeb upstream.
The endpoint IDs in the display graph are expected to match the
associated display path number, i.e. all endpoints connected to
mmsys_ep_main must have reg = <0> and all endpoints connected to
mmsys_ep_ext must have reg = <1>.
Add the missing ID to all endpoints in the display graph, based on
mt8365.dtsi as an existing example that does this correctly.
Fixes: e72d63fa05 ("arm64: dts: mediatek: mt8183: Migrate to display controller OF graph")
Reported-by: Evans Jahja <evansjahja13@gmail.com>
Closes: https://lore.kernel.org/linux-mediatek/CAAq5pW9o3itC0G16LnJO7KMAQ_XoqXUpB=cuJ_7e3-H11zKd5Q@mail.gmail.com/
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
[Angelo: Fixed dtbs_check issues]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fbe3abb44 upstream.
Qualcomm SC7280 and SM8350 SoCs have slightly different LPASS audio
blocks (v9.4.5 and v9.2), however the LPASS LPI pin controllers are
exactly the same. The driver for SM8350 has two issues, which can be
fixed by simply moving over to SC7280 driver which has them correct:
1. "i2s2_data_groups" listed twice GPIO12, but should have both GPIO12
and GPIO13,
2. "swr_tx_data_groups" contained GPIO5 for "swr_tx_data2" function, but
that function is also available on GPIO14, thus listing it twice is
not necessary. OTOH, GPIO5 has also "swr_rx_data1", so selecting
swr_rx_data function should not block the TX one.
Fixes: be9f6d5638 ("pinctrl: qcom: sm8350-lpass-lpi: add SM8350 LPASS TLMM")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
