Commit graph

37,468 commits

Author SHA1 Message Date
Marc Zyngier
b7493f48c3 KVM: arm64: Eagerly init vgic dist/redist on vgic creation
[ Upstream commit ac6769c8f9 ]

If vgic_allocate_private_irqs_locked() fails for any odd reason,
we exit kvm_vgic_create() early, leaving dist->rd_regions uninitialised.

kvm_vgic_dist_destroy() then comes along and walks into the weeds
trying to free the RDs. Got to love this stuff.

Solve it by moving all the static initialisation early, and make
sure that if we fail halfway, we're in a reasonable shape to
perform the rest of the teardown. While at it, reset the vgic model
on failure, just in case...

Reported-by: syzbot+f6a46b038fc243ac0175@syzkaller.appspotmail.com
Tested-by: syzbot+f6a46b038fc243ac0175@syzkaller.appspotmail.com
Fixes: b3aa9283c0 ("KVM: arm64: vgic: Hoist SGI/PPI alloc from vgic_init() to kvm_create_vgic()")
Link: https://lore.kernel.org/r/69a2d58c.050a0220.3a55be.003b.GAE@google.com
Link: https://patch.msgid.link/20260228164559.936268-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-19 16:08:49 +01:00
Sascha Bischoff
2a01a93ed2 KVM: arm64: gic: Set vgic_model before initing private IRQs
[ Upstream commit 9435c1e143 ]

Different GIC types require the private IRQs to be initialised
differently. GICv5 is the culprit as it supports both a different
number of private IRQs, and all of these are PPIs (there are no
SGIs). Moreover, as GICv5 uses the top bits of the interrupt ID to
encode the type, the intid also needs to computed differently.

Up until now, the GIC model has been set after initialising the
private IRQs for a VCPU. Move this earlier to ensure that the GIC
model is available when configuring the private IRQs. While we're at
it, also move the setting of the in_kernel flag and implementation
revision to keep them grouped together as before.

Signed-off-by: Sascha Bischoff <sascha.bischoff@arm.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20260128175919.3828384-7-sascha.bischoff@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Stable-dep-of: ac6769c8f9 ("KVM: arm64: Eagerly init vgic dist/redist on vgic creation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-19 16:08:49 +01:00
Piotr Jaroszynski
6f92a7a8b4 arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults
commit 97c5550b76 upstream.

contpte_ptep_set_access_flags() compared the gathered ptep_get() value
against the requested entry to detect no-ops. ptep_get() ORs AF/dirty
from all sub-PTEs in the CONT block, so a dirty sibling can make the
target appear already-dirty. When the gathered value matches entry, the
function returns 0 even though the target sub-PTE still has PTE_RDONLY
set in hardware.

For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may
set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered
across the CONT range. But page-table walkers that evaluate each
descriptor individually (e.g. a CPU without DBM support, or an SMMU
without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the
unchanged target sub-PTE, causing an infinite fault loop.

Gathering can therefore cause false no-ops when only a sibling has been
updated:
 - write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared)
 - read faults:  target still lacks PTE_AF

Fix by checking each sub-PTE against the requested AF/dirty/write state
(the same bits consumed by __ptep_set_access_flags()), using raw
per-PTE values rather than the gathered ptep_get() view, before
returning no-op. Keep using the raw target PTE for the write-bit unfold
decision.

Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT
range may become the effective cached translation and software must
maintain consistent attributes across the range.

Fixes: 4602e5757b ("arm64/mm: wire up PTE_CONT for user mappings")
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Breno Leitao <leitao@debian.org>
Cc: stable@vger.kernel.org
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Piotr Jaroszynski <pjaroszynski@nvidia.com>
Acked-by: Balbir Singh <balbirs@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-19 16:08:38 +01:00
Catalin Marinas
439b5fb728 arm64: mm: Add PTE_DIRTY back to PAGE_KERNEL* to fix kexec/hibernation
commit c25c4aa3f7 upstream.

Commit 143937ca51 ("arm64, mm: avoid always making PTE dirty in
pte_mkwrite()") changed pte_mkwrite_novma() to only clear PTE_RDONLY
when PTE_DIRTY is set. This was to allow writable-clean PTEs for swap
pages that haven't actually been written.

However, this broke kexec and hibernation for some platforms. Both go
through trans_pgd_create_copy() -> _copy_pte(), which calls
pte_mkwrite_novma() to make the temporary linear-map copy fully
writable. With the updated pte_mkwrite_novma(), read-only kernel pages
(without PTE_DIRTY) remain read-only in the temporary mapping.
While such behaviour is fine for user pages where hardware DBM or
trapping will make them writeable, subsequent in-kernel writes by the
kexec relocation code will fault.

Add PTE_DIRTY back to all _PAGE_KERNEL* protection definitions. This was
the case prior to 5.4, commit aa57157be6 ("arm64: Ensure
VM_WRITE|VM_SHARED ptes are clean by default"). With the kernel
linear-map PTEs always having PTE_DIRTY set, pte_mkwrite_novma()
correctly clears PTE_RDONLY.

Fixes: 143937ca51 ("arm64, mm: avoid always making PTE dirty in pte_mkwrite()")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: stable@vger.kernel.org
Reported-by: Jianpeng Chang <jianpeng.chang.cn@windriver.com>
Link: https://lore.kernel.org/r/20251204062722.3367201-1-jianpeng.chang.cn@windriver.com
Cc: Will Deacon <will@kernel.org>
Cc: Huang, Ying <ying.huang@linux.alibaba.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Huang Ying <ying.huang@linux.alibaba.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-19 16:08:37 +01:00
Catalin Marinas
db377ed4ec arm64: gcs: Honour mprotect(PROT_NONE) on shadow stack mappings
commit 47a8aad135 upstream.

vm_get_page_prot() short-circuits the protection_map[] lookup for a
VM_SHADOW_STACK mapping since it uses a different PIE index from the
typical read/write/exec permissions. However, the side effect is that it
also ignores mprotect(PROT_NONE) by creating an accessible PTE.

Special-case the !(vm_flags & VM_ACCESS_FLAGS) flags to use the
protection_map[VM_NONE] permissions instead. No GCS attributes are
required for an inaccessible PTE.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 6497b66ba6 ("arm64/mm: Map pages for guarded control stack")
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: David Hildenbrand <david@kernel.org>
Reviewed-by: David Hildenbrand (Arm) <david@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-19 16:08:34 +01:00
Marc Zyngier
213e82ccde KVM: arm64: pkvm: Fallback to level-3 mapping on host stage-2 fault
commit 8531d5a83d upstream.

If, for any odd reason, we cannot converge to mapping size that is
completely contained in a memblock region, we fail to install a S2
mapping and go back to the faulting instruction. Rince, repeat.

This happens when faulting in regions that are smaller than a page
or that do not have PAGE_SIZE-aligned boundaries (as witnessed on
an O6 board that refuses to boot in protected mode).

In this situation, fallback to using a PAGE_SIZE mapping anyway --
it isn't like we can go any lower.

Fixes: e728e70580 ("KVM: arm64: Adjust range correctly during host stage-2 faults")
Link: https://lore.kernel.org/r/86wlzr77cn.wl-maz@kernel.org
Cc: stable@vger.kernel.org
Cc: Quentin Perret <qperret@google.com>
Reviewed-by: Quentin Perret <qperret@google.com>
Link: https://patch.msgid.link/20260305132751.2928138-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-19 16:08:25 +01:00
Marc Zyngier
686c8f1611 KVM: arm64: Fix protected mode handling of pages larger than 4kB
commit 08f97454b7 upstream.

Since 3669ddd8fa ("KVM: arm64: Add a range to pkvm_mappings"),
pKVM tracks the memory that has been mapped into a guest in a
side data structure. Crucially, it uses it to find out whether
a page has already been mapped, and therefore refuses to map it
twice. So far, so good.

However, this very patch completely breaks non-4kB page support,
with guests being unable to boot. The most obvious symptom is that
we take the same fault repeatedly, and not making forward progress.
A quick investigation shows that this is because of the above
rejection code.

As it turns out, there are multiple issues at play:

- while the HPFAR_EL2 register gives you the faulting IPA minus
  the bottom 12 bits, it will still give you the extra bits that
  are part of the page offset for anything larger than 4kB,
  even for a level-3 mapping

- pkvm_pgtable_stage2_map() assumes that the address passed as
  a parameter is aligned to the size of the intended mapping

- the faulting address is only aligned for a non-page mapping

When the planets are suitably aligned (pun intended), the guest
faults on a page by accessing it past the bottom 4kB, and extra bits
get set in the HPFAR_EL2 register. If this results in a page mapping
(which is likely with large granule sizes), nothing aligns it further
down, and pkvm_mapping_iter_first() finds an intersection that
doesn't really exist. We assume this is a spurious fault and return
-EAGAIN. And again...

This doesn't hit outside of the protected code, as the page table
code always aligns the IPA down to a page boundary, hiding the issue
for everyone else.

Fix it by always forcing the alignment on vma_pagesize, irrespective
of the value of vma_pagesize.

Fixes: 3669ddd8fa ("KVM: arm64: Add a range to pkvm_mappings")
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://https://patch.msgid.link/20260222141000.3084258-1-maz@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-19 16:08:24 +01:00
Nathan Chancellor
861aa1be41 kbuild: Split .modinfo out from ELF_DETAILS
commit 8678591b47 upstream.

Commit 3e86e4d74c ("kbuild: keep .modinfo section in
vmlinux.unstripped") added .modinfo to ELF_DETAILS while removing it
from COMMON_DISCARDS, as it was needed in vmlinux.unstripped and
ELF_DETAILS was present in all architecture specific vmlinux linker
scripts. While this shuffle is fine for vmlinux, ELF_DETAILS and
COMMON_DISCARDS may be used by other linker scripts, such as the s390
and x86 compressed boot images, which may not expect to have a .modinfo
section. In certain circumstances, this could result in a bootloader
failing to load the compressed kernel [1].

Commit ddc6cbef3e ("s390/boot/vmlinux.lds.S: Ensure bzImage ends with
SecureBoot trailer") recently addressed this for the s390 bzImage but
the same bug remains for arm, parisc, and x86. The presence of .modinfo
in the x86 bzImage was the root cause of the issue worked around with
commit d50f210913 ("kbuild: align modinfo section for Secureboot
Authenticode EDK2 compat"). misc.c in arch/x86/boot/compressed includes
lib/decompress_unzstd.c, which in turn includes lib/xxhash.c and its
MODULE_LICENSE / MODULE_DESCRIPTION macros due to the STATIC definition.

Split .modinfo out from ELF_DETAILS into its own macro and handle it in
all vmlinux linker scripts. Discard .modinfo in the places where it was
previously being discarded from being in COMMON_DISCARDS, as it has
never been necessary in those uses.

Cc: stable@vger.kernel.org
Fixes: 3e86e4d74c ("kbuild: keep .modinfo section in vmlinux.unstripped")
Reported-by: Ed W <lists@wildgooses.com>
Closes: https://lore.kernel.org/587f25e0-a80e-46a5-9f01-87cb40cfa377@wildgooses.com/ [1]
Tested-by: Ed W <lists@wildgooses.com> # x86_64
Link: https://patch.msgid.link/20260225-separate-modinfo-from-elf-details-v1-1-387ced6baf4b@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-12 07:09:44 -04:00
Catalin Marinas
ca1684dd29 arm64: gcs: Do not set PTE_SHARED on GCS mappings if FEAT_LPA2 is enabled
commit 8a85b31312 upstream.

When FEAT_LPA2 is enabled, bits 8-9 of the PTE replace the
shareability attribute with bits 50-51 of the output address. The
_PAGE_GCS{,_RO} definitions include the PTE_SHARED bits as 0b11 (this
matches the other _PAGE_* definitions) but using this macro directly
leads to the following panic when enabling GCS on a system/model with
LPA2:

  Unable to handle kernel paging request at virtual address fffff1ffc32d8008
  Mem abort info:
    ESR = 0x0000000096000004
    EC = 0x25: DABT (current EL), IL = 32 bits
    SET = 0, FnV = 0
    EA = 0, S1PTW = 0
    FSC = 0x04: level 0 translation fault
  Data abort info:
    ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
    CM = 0, WnR = 0, TnD = 0, TagAccess = 0
    GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
  swapper pgtable: 4k pages, 52-bit VAs, pgdp=0000000060f4d000
  [fffff1ffc32d8008] pgd=100000006184b003, p4d=0000000000000000
  Internal error: Oops: 0000000096000004 [#1]  SMP
  CPU: 0 UID: 0 PID: 513 Comm: gcs_write_fault Tainted: G   M                7.0.0-rc1 #1 PREEMPT
  Tainted: [M]=MACHINE_CHECK
  Hardware name: QEMU QEMU Virtual Machine, BIOS 2025.02-8+deb13u1 11/08/2025
  pstate: 03402005 (nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--)
  pc : zap_huge_pmd+0x168/0x468
  lr : zap_huge_pmd+0x2c/0x468
  sp : ffff800080beb660
  x29: ffff800080beb660 x28: fff00000c2058180 x27: ffff800080beb898
  x26: fff00000c2058180 x25: ffff800080beb820 x24: 00c800010b600f41
  x23: ffffc1ffc30af1a8 x22: fff00000c2058180 x21: 0000ffff8dc00000
  x20: fff00000c2bc6370 x19: ffff800080beb898 x18: ffff800080bebb60
  x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000007
  x14: 000000000000000a x13: 0000aaaacbbbffff x12: 0000000000000000
  x11: 0000ffff8ddfffff x10: 00000000000001fe x9 : 0000ffff8ddfffff
  x8 : 0000ffff8de00000 x7 : 0000ffff8da00000 x6 : fff00000c2bc6370
  x5 : 0000ffff8da00000 x4 : 000000010b600000 x3 : ffffc1ffc0000000
  x2 : fff00000c2058180 x1 : fffff1ffc32d8000 x0 : 000000c00010b600
  Call trace:
   zap_huge_pmd+0x168/0x468 (P)
   unmap_page_range+0xd70/0x1560
   unmap_single_vma+0x48/0x80
   unmap_vmas+0x90/0x180
   unmap_region+0x88/0xe4
   vms_complete_munmap_vmas+0xf8/0x1e0
   do_vmi_align_munmap+0x158/0x180
   do_vmi_munmap+0xac/0x160
   __vm_munmap+0xb0/0x138
   vm_munmap+0x14/0x20
   gcs_free+0x70/0x80
   mm_release+0x1c/0xc8
   exit_mm_release+0x28/0x38
   do_exit+0x190/0x8ec
   do_group_exit+0x34/0x90
   get_signal+0x794/0x858
   arch_do_signal_or_restart+0x11c/0x3e0
   exit_to_user_mode_loop+0x10c/0x17c
   el0_da+0x8c/0x9c
   el0t_64_sync_handler+0xd0/0xf0
   el0t_64_sync+0x198/0x19c
  Code: aa1603e2 d34cfc00 cb813001 8b011861 (f9400420)

Similarly to how the kernel handles protection_map[], use a
gcs_page_prot variable to store the protection bits and clear PTE_SHARED
if LPA2 is enabled.

Also remove the unused PAGE_GCS{,_RO} macros.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 6497b66ba6 ("arm64/mm: Map pages for guarded control stack")
Reported-by: Emanuele Rocca <emanuele.rocca@arm.com>
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: David Hildenbrand (Arm) <david@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-03-12 07:09:40 -04:00
Shawn Lin
e5bdc2159f arm64: dts: rockchip: Fix rk3588 PCIe range mappings
[ Upstream commit 46c56b7371 ]

The pcie bus address should be mapped 1:1 to the cpu side MMIO address, so
that there is no same address allocated from normal system memory. Otherwise
it's broken if the same address assigned to the EP for DMA purpose.Fix it to
sync with the vendor BSP.

Fixes: 0acf4fa7f1 ("arm64: dts: rockchip: add PCIe3 support for rk3588")
Fixes: 8d81b77f4c ("arm64: dts: rockchip: add rk3588 PCIe2 support")
Cc: stable@vger.kernel.org
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/1767600929-195341-2-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-12 07:09:29 -04:00
Shawn Lin
7f8f4acf39 arm64: dts: rockchip: Fix rk356x PCIe range mappings
[ Upstream commit f63ea193a4 ]

The pcie bus address should be mapped 1:1 to the cpu side MMIO address, so
that there is no same address allocated from normal system memory. Otherwise
it's broken if the same address assigned to the EP for DMA purpose.Fix it to
sync with the vendor BSP.

Fixes: 568a67e742 ("arm64: dts: rockchip: Fix rk356x PCIe register and range mappings")
Fixes: 66b51ea7d7 ("arm64: dts: rockchip: Add rk3568 PCIe2x1 controller")
Cc: stable@vger.kernel.org
Cc: Andrew Powers-Holmes <aholmes@omnom.net>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/1767600929-195341-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-12 07:09:29 -04:00
Fuad Tabba
519b1ad91d bpf, arm64: Force 8-byte alignment for JIT buffer to prevent atomic tearing
[ Upstream commit ef06fd16d4 ]

struct bpf_plt contains a u64 target field. Currently, the BPF JIT
allocator requests an alignment of 4 bytes (sizeof(u32)) for the JIT
buffer.

Because the base address of the JIT buffer can be 4-byte aligned (e.g.,
ending in 0x4 or 0xc), the relative padding logic in build_plt() fails
to ensure that target lands on an 8-byte boundary.

This leads to two issues:
1. UBSAN reports misaligned-access warnings when dereferencing the
   structure.
2. More critically, target is updated concurrently via WRITE_ONCE() in
   bpf_arch_text_poke() while the JIT'd code executes ldr. On arm64,
   64-bit loads/stores are only guaranteed to be single-copy atomic if
   they are 64-bit aligned. A misaligned target risks a torn read,
   causing the JIT to jump to a corrupted address.

Fix this by increasing the allocation alignment requirement to 8 bytes
(sizeof(u64)) in bpf_jit_binary_pack_alloc(). This anchors the base of
the JIT buffer to an 8-byte boundary, allowing the relative padding math
in build_plt() to correctly align the target field.

Fixes: b2ad54e153 ("bpf, arm64: Implement bpf_arch_text_poke() for arm64")
Signed-off-by: Fuad Tabba <tabba@google.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20260226075525.233321-1-tabba@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-12 07:09:21 -04:00
Will Deacon
3d64dcc079 arm64: io: Extract user memory type in ioremap_prot()
[ Upstream commit 8f09803713 ]

The only caller of ioremap_prot() outside of the generic ioremap()
implementation is generic_access_phys(), which passes a 'pgprot_t' value
determined from the user mapping of the target 'pfn' being accessed by
the kernel. On arm64, the 'pgprot_t' contains all of the non-address
bits from the pte, including the permission controls, and so we end up
returning a new user mapping from ioremap_prot() which faults when
accessed from the kernel on systems with PAN:

  | Unable to handle kernel read from unreadable memory at virtual address ffff80008ea89000
  | ...
  | Call trace:
  |   __memcpy_fromio+0x80/0xf8
  |   generic_access_phys+0x20c/0x2b8
  |   __access_remote_vm+0x46c/0x5b8
  |   access_remote_vm+0x18/0x30
  |   environ_read+0x238/0x3e8
  |   vfs_read+0xe4/0x2b0
  |   ksys_read+0xcc/0x178
  |   __arm64_sys_read+0x4c/0x68

Extract only the memory type from the user 'pgprot_t' in ioremap_prot()
and assert that we're being passed a user mapping, to protect us against
any changes in future that may require additional handling. To avoid
falsely flagging users of ioremap(), provide our own ioremap() macro
which simply wraps __ioremap_prot().

Cc: Zeng Heng <zengheng4@huawei.com>
Cc: Jinjiang Tu <tujinjiang@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 893dea9ccd ("arm64: Add HAVE_IOREMAP_PROT support")
Reported-by: Jinjiang Tu <tujinjiang@huawei.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-12 07:09:18 -04:00
Will Deacon
835da0da68 arm64: io: Rename ioremap_prot() to __ioremap_prot()
[ Upstream commit f6bf47ab32 ]

Rename our ioremap_prot() implementation to __ioremap_prot() and convert
all arch-internal callers over to the new function.

ioremap_prot() remains as a #define to __ioremap_prot() for
generic_access_phys() and will be subsequently extended to handle user
permissions in 'prot'.

Cc: Zeng Heng <zengheng4@huawei.com>
Cc: Jinjiang Tu <tujinjiang@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Stable-dep-of: 8f09803713 ("arm64: io: Extract user memory type in ioremap_prot()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-12 07:09:17 -04:00
Fuad Tabba
bce3847f7c KVM: arm64: Fix ID register initialization for non-protected pKVM guests
[ Upstream commit 7e7c2cf002 ]

In protected mode, the hypervisor maintains a separate instance of
the `kvm` structure for each VM. For non-protected VMs, this structure is
initialized from the host's `kvm` state.

Currently, `pkvm_init_features_from_host()` copies the
`KVM_ARCH_FLAG_ID_REGS_INITIALIZED` flag from the host without the
underlying `id_regs` data being initialized. This results in the
hypervisor seeing the flag as set while the ID registers remain zeroed.

Consequently, `kvm_has_feat()` checks at EL2 fail (return 0) for
non-protected VMs. This breaks logic that relies on feature detection,
such as `ctxt_has_tcrx()` for TCR2_EL1 support. As a result, certain
system registers (e.g., TCR2_EL1, PIR_EL1, POR_EL1) are not
saved/restored during the world switch, which could lead to state
corruption.

Fix this by explicitly copying the ID registers from the host `kvm` to
the hypervisor `kvm` for non-protected VMs during initialization, since
we trust the host with its non-protected guests' features. Also ensure
`KVM_ARCH_FLAG_ID_REGS_INITIALIZED` is cleared initially in
`pkvm_init_features_from_host` so that `vm_copy_id_regs` can properly
initialize them and set the flag once done.

Fixes: 41d6028e28 ("KVM: arm64: Convert the SVE guest vcpu flag to a vm flag")
Signed-off-by: Fuad Tabba <tabba@google.com>
Link: https://patch.msgid.link/20260213143815.1732675-4-tabba@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-12 07:09:08 -04:00
Fuad Tabba
7a15a1e322 KVM: arm64: Hide S1POE from guests when not supported by the host
[ Upstream commit f66857bafd ]

When CONFIG_ARM64_POE is disabled, KVM does not save/restore POR_EL1.
However, ID_AA64MMFR3_EL1 sanitisation currently exposes the feature to
guests whenever the hardware supports it, ignoring the host kernel
configuration.

If a guest detects this feature and attempts to use it, the host will
fail to context-switch POR_EL1, potentially leading to state corruption.

Fix this by masking ID_AA64MMFR3_EL1.S1POE in the sanitised system
registers, preventing KVM from advertising the feature when the host
does not support it (i.e. system_supports_poe() is false).

Fixes: 70ed723829 ("KVM: arm64: Sanitise ID_AA64MMFR3_EL1")
Signed-off-by: Fuad Tabba <tabba@google.com>
Link: https://patch.msgid.link/20260213143815.1732675-2-tabba@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-12 07:09:08 -04:00
Marc Zyngier
c954666a07 arm64: Fix sampling the "stable" virtual counter in preemptible section
[ Upstream commit e5cb94ba5f ]

Ben reports that when running with CONFIG_DEBUG_PREEMPT, using
__arch_counter_get_cntvct_stable() results in well deserves warnings,
as we access a per-CPU variable without preemption disabled.

Fix the issue by disabling preemption on reading the counter. We can
probably do a lot better by not disabling preemption on systems that
do not require horrible workarounds to return a valid counter value,
but this plugs the issue for the time being.

Fixes: 29cc0f3aa7 ("arm64: Force the use of CNTVCT_EL0 in __delay()")
Reported-by: Ben Horgan <ben.horgan@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/aZw3EGs4rbQvbAzV@e134344.arm.com
Tested-by: Ben Horgan <ben.horgan@arm.com>
Tested-by: André Draszik <andre.draszik@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:36 -05:00
Marc Zyngier
53002567af arm64: Force the use of CNTVCT_EL0 in __delay()
[ Upstream commit 29cc0f3aa7 ]

Quentin forwards a report from Hyesoo Yu, describing an interesting
problem with the use of WFxT in __delay() when a vcpu is loaded and
that KVM is *not* in VHE mode (either nVHE or hVHE).

In this case, CNTVOFF_EL2 is set to a non-zero value to reflect the
state of the guest virtual counter. At the same time, __delay() is
using get_cycles() to read the counter value, which is indirected to
reading CNTPCT_EL0.

The core of the issue is that WFxT is using the *virtual* counter,
while the kernel is using the physical counter, and that the offset
introduces a really bad discrepancy between the two.

Fix this by forcing the use of CNTVCT_EL0, making __delay() consistent
irrespective of the value of CNTVOFF_EL2.

Reported-by: Hyesoo Yu <hyesoo.yu@samsung.com>
Reported-by: Quentin Perret <qperret@google.com>
Reviewed-by: Quentin Perret <qperret@google.com>
Fixes: 7d26b0516a ("arm64: Use WFxT for __delay() when possible")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/ktosachvft2cgqd5qkukn275ugmhy6xrhxur4zqpdxlfr3qh5h@o3zrfnsq63od
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:34 -05:00
Marco Elver
956d54e07c arm64: Fix non-atomic __READ_ONCE() with CONFIG_LTO=y
[ Upstream commit bb0c99e08a ]

The implementation of __READ_ONCE() under CONFIG_LTO=y incorrectly
qualified the fallback "once" access for types larger than 8 bytes,
which are not atomic but should still happen "once" and suppress common
compiler optimizations.

The cast `volatile typeof(__x)` applied the volatile qualifier to the
pointer type itself rather than the pointee. This created a volatile
pointer to a non-volatile type, which violated __READ_ONCE() semantics.

Fix this by casting to `volatile typeof(*__x) *`.

With a defconfig + LTO + debug options build, we see the following
functions to be affected:

	xen_manage_runstate_time (884 -> 944 bytes)
	xen_steal_clock (248 -> 340 bytes)
	  ^-- use __READ_ONCE() to load vcpu_runstate_info structs

Fixes: e35123d83e ("arm64: lto: Strengthen READ_ONCE() to acquire when CONFIG_LTO=y")
Cc: stable@vger.kernel.org
Reviewed-by: Boqun Feng <boqun@kernel.org>
Signed-off-by: Marco Elver <elver@google.com>
Tested-by: David Laight <david.laight.linux@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:21 -05:00
Joey Gouly
4612425071 arm64: poe: fix stale POR_EL0 values for ptrace
[ Upstream commit 1f3b950492 ]

If a process wrote to POR_EL0 and then crashed before a context switch
happened, the coredump would contain an incorrect value for POR_EL0.

The value read in poe_get() would be a stale value left in thread.por_el0.  Fix
this by reading the value from the system register, if the target thread is the
current thread.

This matches what gcs/fpsimd do.

Fixes: 1751981992 ("arm64/ptrace: add support for FEAT_POE")
Reported-by: David Spickett <david.spickett@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Kevin Brodsky <kevin.brodsky@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:18 -05:00
Alexey Charkov
d6e866f3a1 arm64: dts: rockchip: Explicitly request UFS reset pin on RK3576
[ Upstream commit 79a3286e61 ]

Rockchip RK3576 UFS controller uses a dedicated pin to reset the connected
UFS device, which can operate either in a hardware controlled mode or as a
GPIO pin.

Power-on default is GPIO mode, but the boot ROM reconfigures it to a
hardware controlled mode if it uses UFS to load the next boot stage.

Given that existing bindings (and rk3576.dtsi) expect a GPIO-controlled
device reset, request the required pin config explicitly.

The pin is requested with pull-down enabled, which is in line with the
SoC power-on default and helps ensure that the attached UFS chip stays
in reset until the driver takes over the control of the respective
GPIO line.

This doesn't appear to affect Linux, but it does affect U-boot:

Before:
=> md.l 0x2604b398
2604b398: 00000011 00000000 00000000 00000000  ................
< ... snip ... >
=> ufs init
ufshcd-rockchip ufshc@2a2d0000: [RX, TX]: gear=[3, 3], lane[2, 2], pwr[FASTAUTO_MODE, FASTAUTO_MODE], rate = 2
=> md.l 0x2604b398
2604b398: 00000011 00000000 00000000 00000000  ................

After:
=> md.l 0x2604b398
2604b398: 00000011 00000000 00000000 00000000  ................
< ... snip ...>
=> ufs init
ufshcd-rockchip ufshc@2a2d0000: [RX, TX]: gear=[3, 3], lane[2, 2], pwr[FASTAUTO_MODE, FASTAUTO_MODE], rate = 2
=> md.l 0x2604b398
2604b398: 00000010 00000000 00000000 00000000  ................

(0x2604b398 is the respective pin mux register, with its BIT0 driving the
mode of UFS_RST: unset = GPIO, set = hardware controlled UFS_RST)

This helps ensure that GPIO-driven device reset actually fires when the
system requests it, not when whatever black box magic inside the UFSHC
decides to reset the flash chip.

Cc: stable@vger.kernel.org
Fixes: c75e5e010f ("scsi: arm64: dts: rockchip: Add UFS support for RK3576 SoC")
Reported-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://patch.msgid.link/20260121-ufs-rst-v3-1-35839bcb4ca7@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:13 -05:00
Zenghui Yu (Huawei)
25056a2fc0 KVM: arm64: nv: Return correct RES0 bits for FGT registers
[ Upstream commit 2eb80a2eee ]

We had extended the sysreg masking infrastructure to more general
registers, instead of restricting it to VNCR-backed registers, since
commit a016202009 ("KVM: arm64: Extend masking facility to arbitrary
registers"). Fix kvm_get_sysreg_res0() to reflect this fact.

Note that we're sure that we only deal with FGT registers in
kvm_get_sysreg_res0(), the

	if (sr < __VNCR_START__)

is actually a never false, which should probably be removed later.

Fixes: 69c19e047d ("KVM: arm64: Add TCR2_EL2 to the sysreg arrays")
Signed-off-by: Zenghui Yu (Huawei) <zenghui.yu@linux.dev>
Link: https://patch.msgid.link/20260121101631.41037-1-zenghui.yu@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:12 -05:00
Jun Yan
21fde0b4b1 arm64: dts: rockchip: Do not enable hdmi_sound node on Pinebook Pro
[ Upstream commit b18247f9da ]

Remove the redundant enabling of the hdmi_sound node in the Pinebook Pro
board dts file, because the HDMI output is unused on this device. [1][2]

This change also eliminates the following kernel log warning, which is
caused by the unenabled dependent node of hdmi_sound that ultimately
results in the node's probe failure:

  platform hdmi-sound: deferred probe pending: asoc-simple-card: parse error

[1] https://files.pine64.org/doc/PinebookPro/pinebookpro_v2.1_mainboard_schematic.pdf
[2] https://files.pine64.org/doc/PinebookPro/pinebookpro_schematic_v21a_20220419.pdf

Cc: stable@vger.kernel.org
Fixes: 5a65505a69 ("arm64: dts: rockchip: Add initial support for Pinebook Pro")
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://patch.msgid.link/20260116151253.9223-1-jerrysteve1101@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:08 -05:00
Shawn Lin
26b1c59da5 arm64: dts: rockchip: Fix SD card support for RK3576 EVB1
[ Upstream commit 7226664bf9 ]

When runtime suspend is enabled, the associated power domain is powered
off, which resets the registers, including the power control bit. As a result,
the card loses power during runtime suspend. The card should still be able
to process I/O with the help of mmc_blk_mq_rw_recovery(), which is suboptimal.
To address this issue, we must use vmmc-supply with a GPIO based method to
maintain power to the card. Also, add cd-gpios method to make hot-plug work
correctly during idle periods.

Fixes: f135a1a073 ("arm64: dts: rockchip: Add rk3576 evb1 board")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/1768524932-163929-5-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:07 -05:00
Janne Grunau
a2ac388aa8 arm64: dts: apple: t8112-j473: Keep the HDMI port powered on
[ Upstream commit 3e4e729325 ]

Add the display controller and DPTX phy power-domains to the framebuffer
node to keep the framebuffer and display out working after device probing
finished.
The OS has more control about the display pipeline used for the HDMI
output on M2 based devices. The HDMI output is driven by an integrated
DisplayPort to HDMI converter (Parade PS190). The DPTX phy is now
controlled by the OS and no longer by firmware running on the display
co-processor. This allows using the second display controller on the
second USB type-c port or tunneling 2 DisplayPort connections over
USB4/Thunderbolt.
The m1n1 bootloader uses the second display controller to drive the HDMI
output. Adjust for this difference compared to the notebooks as well.

Fixes: 2d5ce3fbef ("arm64: dts: apple: t8112: Initial t8112 (M2) device trees")
Cc: stable@vger.kernel.org
Signed-off-by: Janne Grunau <j@jannau.net>
Link: https://patch.msgid.link/20260108-apple-dt-pmgr-fixes-v1-1-cfdce629c0a8@jannau.net
Signed-off-by: Sven Peter <sven@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:21:00 -05:00
Breno Leitao
e3e6e2e4d6 arm64: Disable branch profiling for all arm64 code
[ Upstream commit f22c81bebf ]

The arm64 kernel doesn't boot with annotated branches
(PROFILE_ANNOTATED_BRANCHES) enabled and CONFIG_DEBUG_VIRTUAL together.

Bisecting it, I found that disabling branch profiling in arch/arm64/mm
solved the problem. Narrowing down a bit further, I found that
physaddr.c is the file that needs to have branch profiling disabled to
get the machine to boot.

I suspect that it might invoke some ftrace helper very early in the boot
process and ftrace is still not enabled(!?).

Rather than playing whack-a-mole with individual files, disable branch
profiling for the entire arch/arm64 tree, similar to what x86 already
does in arch/x86/Kbuild.

Cc: stable@vger.kernel.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:20:59 -05:00
Yeoreum Yun
58bd8c5f67 arm64: kernel: initialize missing kexec_buf->random field
[ Upstream commit 15dd20dda9 ]

Commit bf454ec31a ("kexec_file: allow to place kexec_buf randomly")
introduced the kexec_buf->random field to enable random placement of
kexec_buf.

However, this field was never properly initialized for kexec images
that do not need to be placed randomly, leading to the following UBSAN
warning:

[  +0.364528] ------------[ cut here ]------------
[  +0.000019] UBSAN: invalid-load in ./include/linux/kexec.h:210:12
[  +0.000131] load of value 2 is not a valid value for type 'bool' (aka '_Bool')
[  +0.000003] CPU: 4 UID: 0 PID: 927 Comm: kexec Not tainted 6.18.0-rc7+ #3 PREEMPT(full)
[  +0.000002] Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015
[  +0.000000] Call trace:
[  +0.000001]  show_stack+0x24/0x40 (C)
[  +0.000006]  __dump_stack+0x28/0x48
[  +0.000002]  dump_stack_lvl+0x7c/0xb0
[  +0.000002]  dump_stack+0x18/0x34
[  +0.000001]  ubsan_epilogue+0x10/0x50
[  +0.000002]  __ubsan_handle_load_invalid_value+0xc8/0xd0
[  +0.000003]  locate_mem_hole_callback+0x28c/0x2a0
[  +0.000003]  kexec_locate_mem_hole+0xf4/0x2f0
[  +0.000001]  kexec_add_buffer+0xa8/0x178
[  +0.000002]  image_load+0xf0/0x258
[  +0.000001]  __arm64_sys_kexec_file_load+0x510/0x718
[  +0.000002]  invoke_syscall+0x68/0xe8
[  +0.000001]  el0_svc_common+0xb0/0xf8
[  +0.000002]  do_el0_svc+0x28/0x48
[  +0.000001]  el0_svc+0x40/0xe8
[  +0.000002]  el0t_64_sync_handler+0x84/0x140
[  +0.000002]  el0t_64_sync+0x1bc/0x1c0

To address this, initialise kexec_buf->random field properly.

Fixes: bf454ec31a ("kexec_file: allow to place kexec_buf randomly")
Suggested-by: Breno Leitao <leitao@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/all/oninomspajhxp4omtdapxnckxydbk2nzmrix7rggmpukpnzadw@c67o7njgdgm3/ [1]
Link: https://lore.kernel.org/all/20250825180531.94bfb86a26a43127c0a1296f@linux-foundation.org/ [2]
Link: https://lkml.kernel.org/r/20250826-akpm-v1-1-3c831f0e3799@debian.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:20:58 -05:00
Krzysztof Kozlowski
5d83ae6ccd arm64: dts: qcom: sm8750: Fix BAM DMA probing
[ Upstream commit 1c6192ec9c ]

Bindings always required "qcom,num-ees" and "num-channels" properties,
as reported by dtbs_check:

  sm8750-mtp.dtb: dma-controller@1dc4000 (qcom,bam-v1.7.4): 'anyOf' conditional failed, one must be fixed:
    'qcom,powered-remotely' is a required property
    'num-channels' is a required property
    'qcom,num-ees' is a required property
    'clocks' is a required property
    'clock-names' is a required property

However since commit 5068b52548 ("dmaengine: qcom: bam_dma: Fix DT
error handling for num-channels/ees") missing properties are actually
fatal and BAM does not probe:

  bam-dma-engine 1dc4000.dma-controller: num-channels unspecified in dt
  bam-dma-engine 1dc4000.dma-controller: probe with driver bam-dma-engine failed with error -22

Fixes: eeb0f3e4ea ("arm64: dts: qcom: sm8750: Add QCrypto nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251229115734.205744-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:20:58 -05:00
Abel Vesa
b965b990c1 arm64: dts: qcom: x1e80100: Add missing TCSR ref clock to the DP PHYs
[ Upstream commit 0907cab01f ]

The DP PHYs on X1E80100 need the ref clock which is provided by the
TCSR CC.

The current X Elite devices supported upstream work fine without this
clock, because the boot firmware leaves this clock enabled. But we should
not rely on that. Also, even though this change breaks the ABI, it is
needed in order to make the driver disables this clock along with the
other ones, for a proper bring-down of the entire PHY.

So lets attach it to each of the DP PHYs in order to do that.

Cc: stable@vger.kernel.org # v6.9
Fixes: 1940c25eaa ("arm64: dts: qcom: x1e80100: Add display nodes")
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20251224-phy-qcom-edp-add-missing-refclk-v5-3-3f45d349b5ac@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:20:58 -05:00
Alexey Minnekhanov
2e170d8bb3 arm64: dts: qcom: sdm630: Add missing MDSS reset
[ Upstream commit 0c1d1591f8 ]

If the OS does not support recovering the state left by the
bootloader it needs a way to reset display hardware, so that it can
start from a clean state. Add a reference to the relevant reset.

It fixes display init issue appeared in Linux v6.17: without reset
device boots into black screen and you need to turn display off/on
to "fix" it. Also sometimes it can boot into solid blue color
with these messages in kernel log:

  hw recovery is not complete for ctl:2
  [drm:dpu_encoder_phys_vid_prepare_for_kickoff:569] [dpu error]enc33
      intf1 ctl 2 reset failure: -22
  [drm:dpu_encoder_frame_done_timeout:2727] [dpu error]enc33 frame
      done timeout

Fixes: 0e789b491b ("pmdomain: core: Leave powered-on genpds on until sync_state")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251116-sdm660-mdss-reset-v2-3-6219bec0a97f@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:20:56 -05:00
Francesco Dolcini
a803cfad1f arm64: dts: ti: am62p-verdin: Fix SD regulator startup delay
[ Upstream commit de86dbc0fb ]

The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.

Fixes: 87f95ea316 ("arm64: dts: ti: Add Toradex Verdin AM62P")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20251209084126.33282-1-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:20:53 -05:00
Arnd Bergmann
581ed1a5a9 arm64: hugetlbpage: avoid unused-but-set-parameter warning (gcc-16)
[ Upstream commit 729a2e8e9a ]

gcc-16 warns about an instance that older compilers did not:

arch/arm64/mm/hugetlbpage.c: In function 'huge_pte_clear':
arch/arm64/mm/hugetlbpage.c:369:57: error: parameter 'addr' set but not used [-Werror=unused-but-set-parameter=]

The issue here is that __pte_clear() does not actually use its second
argument, but when CONFIG_ARM64_CONTPTE is enabled it still gets
updated.

Replace the macro with an inline function to let the compiler see
the argument getting passed down.

Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dev Jain <dev.jain@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:20:42 -05:00
Diogo Ivo
4567753827 arm64: tegra: smaug: Add usb-role-switch support
[ Upstream commit dfa93788dd ]

The USB2 port on Smaug is configured for OTG operation but lacked the
required 'usb-role-switch' property, leading to a failed probe and a
non-functioning USB port. Add the property along with setting the default
role to host.

Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:19:44 -05:00
Tomas Melin
3983ef126e Revert "arm64: zynqmp: Add an OP-TEE node to the device tree"
[ Upstream commit c197179990 ]

This reverts commit 06d22ed6b6.

OP-TEE logic in U-Boot automatically injects a reserved-memory
node along with optee firmware node to kernel device tree.
The injection logic is dependent on that there is no manually
defined optee node. Having the node in zynqmp.dtsi effectively
breaks OP-TEE's insertion of the reserved-memory node, causing
memory access violations during runtime.

Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20251125-revert-zynqmp-optee-v1-1-d2ce4c0fcaf6@vaisala.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:19:43 -05:00
Jinqian Yang
fd51d47fca arm64: Add support for TSV110 Spectre-BHB mitigation
[ Upstream commit e3baa5d4b3 ]

The TSV110 processor is vulnerable to the Spectre-BHB (Branch History
Buffer) attack, which can be exploited to leak information through
branch prediction side channels. This commit adds the MIDR of TSV110
to the list for software mitigation.

Signed-off-by: Jinqian Yang <yangjinqian1@huawei.com>
Reviewed-by: Zenghui Yu <zenghui.yu@linux.dev>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04 07:19:34 -05:00
Petr Mladek
34de49d097 kallsyms/bpf: rename __bpf_address_lookup() to bpf_address_lookup()
[ Upstream commit cd6735896d ]

bpf_address_lookup() has been used only in kallsyms_lookup_buildid().  It
was supposed to set @modname and @modbuildid when the symbol was in a
module.

But it always just cleared @modname because BPF symbols were never in a
module.  And it did not clear @modbuildid because the pointer was not
passed.

The wrapper is no longer needed.  Both @modname and @modbuildid are now
always initialized to NULL in kallsyms_lookup_buildid().

Remove the wrapper and rename __bpf_address_lookup() to
bpf_address_lookup() because this variant is used everywhere.

[akpm@linux-foundation.org: fix loongarch]
Link: https://lkml.kernel.org/r/20251128135920.217303-6-pmladek@suse.com
Fixes: 9294523e37 ("module: add printk formats to add module build ID to stacktraces")
Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Aaron Tomlin <atomlin@atomlin.com>
Cc: Daniel Borkman <daniel@iogearbox.net>
Cc: Daniel Gomez <da.gomez@samsung.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Kees Cook <kees@kernel.org>
Cc: Luis Chamberalin <mcgrof@kernel.org>
Cc: Marc Rutland <mark.rutland@arm.com>
Cc: "Masami Hiramatsu (Google)" <mhiramat@kernel.org>
Cc: Petr Pavlu <petr.pavlu@suse.com>
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:17 -08:00
Konrad Dybcio
3c0dd95dd5 arm64: dts: qcom: sm6115: Add CX_MEM/DBGC GPU regions
[ Upstream commit 78c13dac18 ]

Describe the GPU register regions, with the former existing but not
being used much if at all on this silicon, and the latter containing
various debugging levers generally related to dumping the state of
the IP upon a crash.

Fixes: 11750af256 ("arm64: dts: qcom: sm6115: Add GPU nodes")
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Closes: https://lore.kernel.org/linux-arm-msm/8a64f70b-8034-45e7-86a3-0015cf357132@oss.qualcomm.com/T/#m404f1425c36b61467760f058b696b8910340a063
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251229-topic-6115_2290_gpu_dbgc-v1-3-4a24d196389c@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:10 -08:00
Konrad Dybcio
58c0b917fd arm64: dts: qcom: agatti: Add CX_MEM/DBGC GPU regions
[ Upstream commit 0fdcc94892 ]

Describe the GPU register regions, with the former existing but not
being used much if at all on this silicon, and the latter containing
various debugging levers generally related to dumping the state of
the IP upon a crash.

Fixes: 4faeef52c8 ("arm64: dts: qcom: qcm2290: Add GPU nodes")
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Closes: https://lore.kernel.org/linux-arm-msm/8a64f70b-8034-45e7-86a3-0015cf357132@oss.qualcomm.com/T/#m404f1425c36b61467760f058b696b8910340a063
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251229-topic-6115_2290_gpu_dbgc-v1-2-4a24d196389c@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:10 -08:00
Viken Dadhaniya
222e45e64b arm64: dts: qcom: talos: Drop opp-shared from QUP OPP table
[ Upstream commit dda4bdd325 ]

QUP devices are currently marked with opp-shared in their OPP table,
causing the kernel to treat them as part of a shared OPP domain. This
leads to the qcom_geni_serial driver failing to probe with error
-EBUSY (-16).

Remove the opp-shared property to ensure the OPP framework treats the
QUP OPP table as device-specific, allowing the serial driver to probe
successfully

Fixes: f6746dc9e3 ("arm64: dts: qcom: qcs615: Add QUPv3 configuration")
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251111170350.525832-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:10 -08:00
Jonathan Marek
37082c9b41 arm64: dts: qcom: x1e: bus is 40-bits (fix 64GB models)
[ Upstream commit b38dd256e1 ]

Unlike the phone SoCs this was copied from, x1e has a 40-bit physical bus.
The upper address space is used to support more than 32GB of memory.

This fixes issues when DMA buffers are allocated outside the 36-bit range.

Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251127212943.24480-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Dmitry Baryshkov
06557d72ea arm64: dts: qcom: sdm845-db845c: specify power for WiFi CH1
[ Upstream commit c303e89f7f ]

Specify power supply for the second chain / antenna output of the
onboard WiFi chip.

Fixes: 3f72e2d3e6 ("arm64: dts: qcom: Add Dragonboard 845c")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-8-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Dmitry Baryshkov
39974be66f arm64: dts: qcom: sdm845-db845c: drop CS from SPIO0
[ Upstream commit 8bfb696ccd ]

On SDM845 SPI uses hardware-provided chip select, while specifying
cs-gpio makes the driver request GPIO pin, which on DB845c conflicts
with the normal host controllers pinctrl entry.

Drop the cs-gpios property to restore SPI functionality.

Fixes: cb29e7106d ("arm64: dts: qcom: db845c: Add support for MCP2517FD")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-7-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Dmitry Baryshkov
2d7ea0516f arm64: dts: qcom: qrb4210-rb2: Fix UART3 wakeup IRQ storm
[ Upstream commit c5dc4812f6 ]

Follow commit 9c92d36b0b ("arm64: dts: qcom: qrb2210-rb1: Fix UART3
wakeup IRQ storm") and apply the similar fix to the RB2 platform.

Having RX / TX pins as pull up and wakup interrupt as high-level
triggered generates an interrupt storm when trying to suspend the
device. Avoid the storm by using the falling edge trigger (as all other
platforms do).

Fixes: cab60b1665 ("arm64: dts: qcom: qrb4210-rb2: Enable bluetooth")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-6-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Jerome Brunet
33bc5e1016 arm64: dts: amlogic: g12: assign the MMC A signal clock
[ Upstream commit 3c941feaa3 ]

The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.

Assign the clock to make sure it is properly configured

Fixes: 8a6b3ca2d3 ("arm64: dts: meson: g12a: add SDIO controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-6-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Jerome Brunet
844317f9b0 arm64: dts: amlogic: g12: assign the MMC B and C signal clocks
[ Upstream commit be2ff5fdb0 ]

The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.

Assign the clocks to make sure they are properly configured

Fixes: 4759fd87b9 ("arm64: dts: meson: g12a: add mmc nodes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-5-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Jerome Brunet
0709a09019 arm64: dts: amlogic: gx: assign the MMC signal clocks
[ Upstream commit 4067065590 ]

The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.

Assign the clocks to make sure they are properly configured

Fixes: 50662499f9 ("ARM64: dts: meson-gx: Use correct mmc clock source 0")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-4-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Jerome Brunet
c9bb634897 arm64: dts: amlogic: axg: assign the MMC signal clocks
[ Upstream commit 13d3fe2318 ]

The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.

Assign the clocks to make sure they are properly configured

Fixes: 221cf34bac ("ARM64: dts: meson-axg: enable the eMMC controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-3-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Jerome Brunet
f6e54c1ea7 arm64: dts: amlogic: c3: assign the MMC signal clocks
[ Upstream commit 69330fd236 ]

The amlogic MMC driver operate with the assumption that MMC clock
is configured to provide 24MHz. It uses this path for low
rates such as 400kHz.

Assign the clocks to make sure they are properly configured

Fixes: 520b792e83 ("arm64: dts: amlogic: add some device nodes for C3")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260114-amlogic-mmc-clocks-followup-v1-1-a999fafbe0aa@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Abhash Kumar Jha
6906a98898 arm64: dts: ti: k3-j784s4-j742s2-main-common.dtsi: Refactor watchdog instances for j784s4
[ Upstream commit 61acc4428a ]

Each A72 core has one watchdog instance associated with it. Since j742s2
has 4 A72 cores, the common file should not define 8 watchdog instances.

Refactor the last 4 extra watchdogs from the common file to j784s4
specific file, as j784s4 has 8 A72 cores and thus hardware description
requires 8 watchdog instances.

Fixes: 9cc161a450 ("arm64: dts: ti: Refactor J784s4 SoC files to a common file")
Signed-off-by: Abhash Kumar Jha <a-kumar2@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://patch.msgid.link/20260112085113.3476193-3-a-kumar2@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:09 -08:00
Abhash Kumar Jha
8273989e77 arm64: dts: ti: k3-j784s4-main.dtsi: Move c71_3 node to appropriate order
[ Upstream commit 24c9d5fb8b ]

The device tree nodes should be ordered by unit addresses in ascending
order.

Correct the order by moving the c71_3 DSP node at the end as it has a
higher unit address.

Signed-off-by: Abhash Kumar Jha <a-kumar2@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://patch.msgid.link/20260112085113.3476193-2-a-kumar2@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Stable-dep-of: 61acc4428a ("arm64: dts: ti: k3-j784s4-j742s2-main-common.dtsi: Refactor watchdog instances for j784s4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-26 14:59:08 -08:00