commit 38b845e1f9 upstream.
The power-limits for ru and mcs and stored in the devicetree as bytewise
array (often with sizes which are not a multiple of 4). These arrays have a
prefix which defines for how many modes a line is applied. This prefix is
also only a byte - but the code still tried to fix the endianness of this
byte with a be32 operation. As result, loading was mostly failing or was
sending completely unexpected values to the firmware.
Since the other rates are also stored in the devicetree as bytewise arrays,
just drop the u32 access + be32_to_cpu conversion and directly access them
as bytes arrays.
Cc: stable@vger.kernel.org
Fixes: 22b980badc ("mt76: add functions for parsing rate power limits from DT")
Fixes: a9627d992b ("mt76: extend DT rate power limits to support 11ax devices")
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8e5a110c0 ]
The Acer A1 840 tablet contains quite generic names in the sys_vendor and
product_name DMI strings, without this patch brcmfmac will try to load:
brcmfmac43340-sdio.Insyde-BayTrail.txt as nvram file which is a bit
too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file name
is used on the Acer A1 840 tablet.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Link: https://patch.msgid.link/20251103100314.353826-1-hansg@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 066f417be5 ]
Set the MT76_STATE_MCU_RUNNING bit only after mt7921_load_clc()
has successfully completed. Previously, the MCU_RUNNING state
was set before loading CLC, which could cause conflict between
chip mcu_init retry and mac_reset flow, result in chip init fail
and chip abnormal status. By moving the state set after CLC load,
firmware initialization becomes robust and resolves init fail issue.
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Reviewed-by: druth@chromium.org
Link: https://patch.msgid.link/19ec8e4465142e774f17801025accd0ae2214092.1763465933.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5511ba3de4 ]
Flip the response rate subchannel. It was backwards, causing low
speeds when using 40 MHz channel width. "iw dev ... station dump"
showed a low RX rate, 11M or less.
Also fix the channel width field of RF6052_REG_MODE_AG.
Tested only with RTL8192CU, but these settings are identical for
RTL8723AU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1f46571d-855b-43e1-8bfc-abacceb96043@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53d1548612 ]
In mt7615_mcu_wtbl_sta_add(), an skb sskb is allocated. If the
subsequent call to mt76_connac_mcu_alloc_wtbl_req() fails, the function
returns an error without freeing sskb, leading to a memory leak.
Fix this by calling dev_kfree_skb() on sskb in the error handling path
to ensure it is properly released.
Fixes: 99c457d902 ("mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251113062415.103611-1-zilin@seu.edu.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fe823b9ee ]
Do not take into account offchannel links for deflink accounting.
Fixes: a3316d2fc6 ("wifi: mt76: mt7996: set vif default link_id adding/removing vif links")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Link: https://patch.msgid.link/20251114-mt76-fix-missing-mtx-v1-4-259ebf11f654@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6aaaaeacf1 ]
Move mt76_abort_scan routine out of mt76_reset_device() in order to
avoid a possible deadlock since mt76_reset_device routine is running
with mt76 mutex help and mt76_abort_scan_complete() can grab mt76 mutex
in some cases.
Fixes: b36d556102 ("wifi: mt76: abort scan/roc on hw restart")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Link: https://patch.msgid.link/20251114-mt76-fix-missing-mtx-v1-3-259ebf11f654@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a4bcba26e ]
Grab mt76 mutex in mt7996_mac_sta_event routine in order to rely on
mt76_dereference() utility macro.
Fixes: ecd72f9695 ("wifi: mt76: mt7996: Support MLO in mt7996_mac_sta_event()")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Link: https://patch.msgid.link/20251114-mt76-fix-missing-mtx-v1-1-259ebf11f654@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4031fec9d ]
The RRO EMI rings only need to be allocated when WED is not active.
This patch fixes command timeout issue for the setting of WED off and
RRO on.
Fixes: 3a29164425 ("wifi: mt76: mt7996: Add SW path for HW-RRO v3.1")
Co-developed-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251106064203.1000505-12-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e11be918d9 ]
This patch fixes the following key issues:
- Pass correct link BSS to mt7996_mcu_add_key(), and use HW beacon
protection mode for mt7990 chipset
- Do not do group key deletion for GTK and IGTK due to FW design, the
delete key command will delete all group keys of a link BSS
- For deleting BIGTK, FW adds a new flow, but the "sec->add" field
should be filled with "SET_KEY". Note that if BIGTK is not deleted, it
will cause beacon decryption issue when switching from an AP interface
to a station interface
Fixes: 0c45d52276 ("wifi: mt76: mt7996: fix setting beacon protection keys")
Co-developed-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Allen Ye <allen.ye@mediatek.com>
Co-developed-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20251106064203.1000505-10-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eaea3a8ba ]
This ensures the upper layer uses the correct link ID during packet
processing.
Fixes: dd82a9e02c ("wifi: mt76: mt7996: Rely on mt7996_sta_link in sta_add/sta_remove callbacks")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251106064203.1000505-7-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e077071e7a ]
For an MLD peer, we only need to call the teardown command when removing
the last link, and there's no need to call mt7996_mcu_add_sta() for the
earlier links.
Fixes: c1d6dd5d03 ("wifi: mt76: mt7996: Add mt7996_mcu_teardown_mld_sta rouine")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251106064203.1000505-6-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb705a6067 ]
Fix several fields in mt7996_mcu_bss_basic_tlv() that were not obtained
from the correct link. Without this patch, the MLD station interface
does not function properly.
Fixes: 34a41bfbcb ("wifi: mt76: mt7996: prepare mt7996_mcu_add_dev/bss_info for MLO support")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251106064203.1000505-5-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d86765828 ]
Fix the ibf_timeout field for mt7996, mt7992 and mt7990 chipsets. For
the mt7992, this value shall be set as 0xff, while the others shall be
set as 0x18.
Fixes: ad4c9a8a98 ("wifi: mt76: mt7996: add implicit beamforming support for mt7992")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20251106064203.1000505-3-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 361b59b6be ]
Since wiphy->available_antennas_tx now accumulates the chainmask of all
the radios of a wiphy, use phy->orig_antenna_mask to get the original
max nss for comparison.
Fixes: 69d54ce749 ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20251106064203.1000505-1-shayne.chen@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb2941a51 ]
This reverts commit 55e95ce469.
mt792x drivers don't seem to support multi-radio devices yet. At least
they don't mess with `struct wiphy_radio` at the moment.
Packet capturing on monitor interface doesn't work after the blamed patch:
tcpdump -i wls6mon -n -vvv
Revert the NO_VIRTUAL_MONITOR feature for now to resolve the issue.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 55e95ce469 ("wifi: mt76: mt792x: improve monitor interface handling")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20251027111843.38975-1-pchelkin@ispras.ru
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 084922069c ]
Remove unnecessary link_id checks in mt7996_tx routine since if the link
identifier provided by mac80211 is unspecified the value will be
overwritten at the beginning on the function.
Fixes: f940c9b7ae ("wifi: mt76: mt7996: Set proper link destination address in mt7996_tx()")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250924-mt76_tx_unnecessary-check-v1-1-e595930a5662@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79277f8ad1 ]
If a link does not have an assigned channel yet, mt7996_vif_link returns
NULL. We still need to store the updated queue settings in that case, and
apply them later.
Move the location of the queue params to within struct mt7996_vif_link.
Fixes: c0df2f0caa ("wifi: mt76: mt7996: prepare mt7996_mcu_set_tx for MLO support")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250929111723.52486-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b647d2574e ]
The rtl8187_rx_cb() calculates the rx descriptor header address
by subtracting its size from the skb tail pointer.
However, it does not validate if the received packet
(skb->len from urb->actual_length) is large enough to contain this
header.
If a truncated packet is received, this will lead to a buffer
underflow, reading memory before the start of the skb data area,
and causing a kernel panic.
Add length checks for both rtl8187 and rtl8187b descriptor headers
before attempting to access them, dropping the packet cleanly if the
check fails.
Fixes: 6f7853f3cb ("rtl8187: change rtl8187_dev.c to support RTL8187B (part 2)")
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251118013258.1789949-2-eeodqql09@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5b9c042b ]
In rtl8180_init_rx_ring(), memory is allocated for skb packets and DMA
allocations in a loop. When an allocation fails, the previously
successful allocations are not freed on exit.
Fix that by jumping to err_free_rings label on error, which calls
rtl8180_free_rx_ring() to free the allocations. Remove the free of
rx_ring in rtl8180_init_rx_ring() error path, and set the freed
priv->rx_buf entry to null, to avoid double free.
Fixes: f653211197 ("Add rtl8180 wireless driver")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251114094527.79842-1-nihaal@cse.iitm.ac.in
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e88e86411 ]
In one of the error paths, the memory allocated for skb_rx is not freed.
Fix that by freeing it before returning.
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Link: https://patch.msgid.link/20251110175316.106591-1-nihaal@cse.iitm.ac.in
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2977567b24 ]
Currently, for beacon_stats, ath12k_mac_get_fw_stats() is called
for each started BSS on the specified hardware.
ath12k_mac_get_fw_stats() will wait for the fw_stats_done completion
after fetching the requested data from firmware. For the beacon_stats,
fw_stats_done completion will be set only when stats are received for
all BSSes. However, for other stats like vdev_stats or pdev_stats, there
is one request to the firmware for all enabled BSSes. Since beacon_stats
is fetched individually for all BSSes enabled in that pdev, waiting for
the completion event results in a timeout error when multiple BSSes are
enabled.
Avoid this by completing the fw_stats_done immediately after
updating the requested BSS's beacon stats in the list. Subsequently,
this list will be used to display the beacon stats for all enabled
BSSes in the requested pdev.
Additionally, remove 'num_bcn_recvd' from the ath12k_fw_stats struct
as it is no longer needed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 9fe4669ae9 ("wifi: ath12k: Request beacon stats from firmware")
Signed-off-by: Manish Dharanenthiran <manish.dharanenthiran@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251031-beacon_stats-v1-2-f52fce7b03ac@qti.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7543818e97 ]
When there is an attempt to write data and RTW89_FLAG_UNPLUGGED is set,
this means device is disconnected and no urb is submitted. Return
appropriate error code to the caller to properly free the allocated
resources.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 2135c28be6 ("wifi: rtw89: Add usb.{c,h}")
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251104135720.321110-3-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a4557528 ]
Allow adding rx_skb to rx_free_queue for later reuse on the common error
handling path, otherwise free it.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 2135c28be6 ("wifi: rtw89: Add usb.{c,h}")
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20251104135720.321110-2-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e70515039d ]
During scan and remain-on-channel requests, a scan link vif (arvif) is
assigned and a temporary vdev is created. If vdev creation fails, the
assigned arvif is left attached until the virtual interface is removed,
leaving a stale link in ahvif.
Fix this by freeing the stale arvif and resetting the corresponding link in
ahvif by calling ath12k_mac_unassign_link_vif() when vdev creation fails.
While at it, propagate the actual error code from ath12k_mac_vdev_create()
instead of returning -EINVAL in ath12k_mac_initiate_hw_scan().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 477cabfdb7 ("wifi: ath12k: modify link arvif creation and removal for MLO")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251026182254.1399650-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 448bf7b514 ]
Currently, vdev limit check is performed only in
ath12k_mac_assign_vif_to_vdev(). If the host has already created
maximum number of vdevs for the radio (ar) and a scan request
arrives for the same radio, ath12k_mac_initiate_hw_scan() attempts
to create a vdev without checking the limit, causing firmware asserts.
Centralize the vdev limit guard by moving the check into
ath12k_mac_vdev_create() so that all callers obey the limit.
While doing this, update the condition from
`num_created_vdevs > (TARGET_NUM_VDEVS(ab) - 1)` to
`num_created_vdevs >= TARGET_NUM_VDEVS(ab)` for clarity and to
eliminate unnecessary arithmetic.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 0d6e6736ed ("wifi: ath12k: scan statemachine changes for single wiphy")
Fixes: 4938ba733e ("wifi: ath12k: modify remain on channel for single wiphy")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251026182254.1399650-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 088a099690 ]
In ath12k_core_init() when ath12k_core_hw_group_create() fails,
ath12k_core_hw_group_destroy() is called where for each device below
path would get executed
ath12k_core_soc_destroy()
ath12k_qmi_deinit_service()
qmi_handle_release()
This results in kernel crash in case one of the device fails at
qmi_handle_init() when creating hardware group:
ath12k_pci 0000:10:00.0: failed to initialize qmi handle
ath12k_pci 0000:10:00.0: failed to initialize qmi :-517
ath12k_pci 0000:10:00.0: failed to create soc core: -517
ath12k_pci 0000:10:00.0: unable to create hw group
BUG: unable to handle page fault for address: ffffffffffffffb7
RIP: 0010:qmi_handle_release
Call Trace:
<TASK>
ath12k_qmi_deinit_service
ath12k_core_hw_group_destroy
ath12k_core_init
ath12k_pci_probe
The detailed reason is, when qmi_handle_init() fails for a device
ab->qmi.handle is not correctly initialized. Then
ath12k_core_hw_group_create() returns failure, since error handing
is done for all device, eventually qmi_handle_release() is called for the
issue device and finally kernel crashes due to the uninitialized
ab->qmi.handle.
Fix this by moving error handling to ath12k_core_hw_group_create(), this
way the issue device can be skipped.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 6f245ea0ec ("wifi: ath12k: introduce device group abstraction")
Link: https://lore.kernel.org/ath12k/fabc97122016d1a66a53ddedd965d134@posteo.net
Reported-by: a-development <a-development@posteo.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220518
Tested-by: a-development <a-development@posteo.de>
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251030-fix-hw-group-create-err-handling-v1-1-0659e4d15fb9@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00575bb44b ]
During firmware recovery or suspend/resume, m3 memory could be reused if
the size of the new m3 binary is equal to or less than that of the
existing memory. There will be issues for the latter case, since
m3_mem->size will be updated with a smaller value and this value is
eventually used in the free path, where the original total size should be
used instead.
To fix it, add a new member in m3_mem_region structure to track the original
memory size and use it in free path.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Fixes: 05090ae82f ("wifi: ath12k: check M3 buffer size as well whey trying to reuse it")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251029-ath12k-fix-m3-reuse-v1-1-69225bacfc5d@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be5febd51c ]
When the call to ath12k_wmi_arp_ns_offload() fails, the temporary memory
allocation for offload is not freed before returning. Fix that by
freeing offload in the error path.
Fixes: 1666108c74 ("wifi: ath12k: support ARP and NS offload")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251028170457.134608-1-nihaal@cse.iitm.ac.in
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3df2849667 ]
Add a missing NULL pointer check after kzalloc() in
iwl_mld_send_proto_offload(). Without this check, a failed
allocation could lead to a NULL dereference.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Link: https://patch.msgid.link/20251017041128.1379715-1-liqiang01@kylinos.cn
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a41281f651 ]
Hardware target implements an address space larger than that PCI BAR can
map. In order to be able to access the whole target address space, the
BAR space is split into 4 segments, of which the last 3, called windows,
can be dynamically mapped to the desired area. This is achieved by
updating WINDOW_REG_ADDRESS register with appropriate window value.
Currently each time when accessing a register that beyond WINDOW_START,
host calculates the window value and caches it after window update,
this way next time when accessing a register falling in the same window,
host knows that the window is already good hence no additional update
needed.
However this mechanism breaks after global reset is triggered in
ath12k_pci_soc_global_reset(), because with global reset hardware resets
WINDOW_REG_ADDRESS register hence the window is not properly mapped any
more. Current host does nothing about this, as a result a subsequent
register access may not work as expected if it falls in a window same as
before.
Although there is no obvious issue seen now, better to fix it to avoid
future problem. The fix is done by restoring the window register after
global reset.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251017-ath12k-reset-window-cache-v1-1-29e0e751deed@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a013ca2d4 ]
In ath11k_wmi_send_peer_assoc_cmd(), peer's transmit MCS is sent to
firmware as receive MCS while peer's receive MCS sent as transmit MCS,
which goes against firmwire's definition.
While connecting to a misbehaved AP that advertises 0xffff (meaning not
supported) for 160 MHz transmit MCS map, firmware crashes due to 0xffff
is assigned to he_mcs->rx_mcs_set field.
Ext Tag: HE Capabilities
[...]
Supported HE-MCS and NSS Set
[...]
Rx and Tx MCS Maps 160 MHz
[...]
Tx HE-MCS Map 160 MHz: 0xffff
Swap the assignment to fix this issue.
As the HE rate control mask is meant to limit our own transmit MCS, it
needs to go via he_mcs->rx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive MCS.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 61fe43e721 ("ath11k: add support for setting fixed HE rate/gi/ltf")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251017-ath11k-mcs-assignment-v1-2-da40825c1783@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47d0cd6bcc ]
While associating, firmware needs to know peer's receive capability to
calculate its own VHT transmit MCS, currently host sends this information
to firmware via mcs->rx_mcs_set field, this is wrong as firmware actually
takes it from mcs->tx_mcs_set field. Till now there is no failure seen
due to this, most likely because almost all peers are advertising the
same capability for both transmit and receive. Swap the assignment to
fix it.
Besides, rate control mask is meant to limit our own transmit MCS, hence
need to go via mcs->tx_mcs_set field. With the aforementioned swapping
done, change is needed as well to apply it to the peer's receive
capability rather than transmit capability.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251017-ath11k-mcs-assignment-v1-1-da40825c1783@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c5f229b13 ]
Currently, the TX and RX MCS rate configurations per peer are
reversed when sent to the firmware. As a result, RX MCS rates
are configured for TX, and vice versa. This commit rectifies
the configuration to match what the firmware expects.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251009211656.2386085-3-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c21b32c2c ]
While associating, firmware needs the peer's receive capability
to calculate its own VHT transmit MCS. Currently, the host
sends this information via mcs->rx_mcs_set field, but firmware
actually reads it from mcs->tx_mcs_set field. This mismatch is
incorrect.
This issue has not caused failures so far because most peers
advertise identical TX and RX capabilities. Fix this by
assigning the value to tx_mcs_set as expected.
Additionally, the rate control mask is intended to limit our
transmit MCS, so it should also apply to the peer's receive
capability. Update the logic accordingly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251009211656.2386085-2-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36f9edbb9d ]
Currently, packets received on the REO exception ring from
unassociated peers are of MSDU buffer type, while the driver expects
link descriptor type packets. These packets are not parsed further due
to a return check on packet type in ath12k_hal_desc_reo_parse_err(),
but the associated skb is not freed. This may lead to kernel
crashes and buffer leaks.
Hence to fix, update the RX error handler to explicitly drop
MSDU buffer type packets received on the REO exception ring.
This prevents further processing of invalid packets and ensures
stability in the RX error handling path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sarika Sharma <sarika.sharma@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250930091551.3305312-2-sarika.sharma@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 596b911644 ]
Hardware target implements an address space larger than that PCI BAR can
map. In order to be able to access the whole target address space, the BAR
space is split into 4 segments, of which the last 3, called windows, can
be dynamically mapped to the desired area. This is achieved by updating
window register with appropriate window value. Currently each time when
accessing a register that beyond ATH11K_PCI_WINDOW_START, host calculates
the window value and caches it after window update, this way next time
when accessing a register falling in the same window, host knows that the
window is already good hence no additional update needed.
However this mechanism breaks after global reset is triggered in
ath11k_pci_soc_global_reset(), because with global reset hardware resets
window register hence the window is not properly mapped any more. Current
host does nothing about this, as a result a subsequent register access may
not work as expected if it falls in a window same as before.
Although there is no obvious issue seen now, better to fix it to avoid
future problem. The fix is done by restoring the window register after
global reset.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251014-ath11k-reset-window-cache-v1-1-b85271b111dd@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f35a07a484 ]
Currently, ath10k has a recovery check logic. It will wait for the
last recovery to finish by wait_for_completion_timeout();
But in SDIO scenarios, the recovery function may be invoked from
interrupt context, where long blocking waits are undesirable and can
lead to system instability.
Additionally, Linux’s ordered workqueue processes one task at a time.
If a previous recovery is still queued or executing, new triggers are
ignored. This prevents accurate tracking of consecutive failures and
delays transition to the WEDGED state.
To address this, move the recovery check logic into a different
workqueue.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00189
Fixes: c256a94d1b ("wifi: ath10k: shutdown driver when hardware is unreliable")
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251014110757.155-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Scanning can be offloaded to the firmware. To that end, the driver
prepares a list of channels to scan, including periodic visits back to
the operating channel, and sends the list to the firmware.
When the channel list is too long to fit in a single H2C message, the
driver splits the list, sends the first part, and tells the firmware to
scan. When the scan is complete, the driver sends the next part of the
list and tells the firmware to scan.
When the last channel that fit in the H2C message is the operating
channel something seems to go wrong in the firmware. It will
acknowledge receiving the list of channels but apparently it will not
do anything more. The AP can't be pinged anymore. The driver still
receives beacons, though.
One way to avoid this is to split the list of channels before the
operating channel.
Affected devices:
* RTL8851BU with firmware 0.29.41.3
* RTL8832BU with firmware 0.29.29.8
* RTL8852BE with firmware 0.29.29.8
The commit 57a5fbe39a ("wifi: rtw89: refactor flow that hw scan handles channel list")
is found by git blame, but it is actually to refine the scan flow, but not
a culprit, so skip Fixes tag.
Reported-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/0abbda91-c5c2-4007-84c8-215679e652e1@gmail.com/
Cc: stable@vger.kernel.org # 6.16+
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/c1e61744-8db4-4646-867f-241b47d30386@gmail.com
One of the factors of a link's grade is the channel load, which is
calculated from the AP's bss load element.
The current code takes this element from the beacon for an active link,
and from bss->ies for an inactive link.
bss->ies is set to either the beacon's ies or to the probe response
ones, with preference to the probe response (meaning that if there was
even one probe response, the ies of it will be stored in bss->ies and
won't be overiden by the beacon ies).
The probe response can be very old, i.e. from the connection time,
where a beacon is updated before each link selection (which is
triggered only after a passive scan).
In such case, the bss load element in the probe response will not
include the channel load caused by the STA, where the beacon will.
This will cause the inactive link to always have a lower channel
load, and therefore an higher grade than the active link's one.
This causes repeated link switches, causing the throughput to drop.
Fix this by always taking the ies from the beacon, as those are for
sure new.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251110145652.b493dbb1853a.I058ba7309c84159f640cc9682d1bda56dd56a536@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
During the development of the rate changes, I evidently made
some changes that shouldn't have been there; beacon templates
with rate_n_flags are only in old versions, so no changes to
them should have been necessary, and evidently broke on some
devices. This also would have broken fixed (injection) rates,
it would seem. Restore the old handling of this.
Fixes: dabc88cb3b ("wifi: iwlwifi: handle v3 rates")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220558
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20251008112044.3bb8ea849d8d.I90f4d2b2c1f62eaedaf304a61d2ab9e50c491c2d@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
The list_for_each_entry() iterator must not be used outside the loop.
Even though we break and check for NULL, doing so still violates kernel
iteration rules and triggers Coccinelle's use_after_iter.cocci warning.
Cache the matched entry in aux_roc_te and use it consistently after the
loop. This follows iterator best practices, resolves the warning, and
makes the code more maintainable.
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Link: https://patch.msgid.link/20251016014919.383565-1-junjie.cao@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
