[ Upstream commit 71cfa7c893 ]
Some Potron SFP+ XGSPON ONU sticks are shipped with different EEPROM
vendor ID and vendor name strings, but are otherwise functionally
identical to the existing "Potron SFP+ XGSPON ONU Stick" handled by
sfp_quirk_potron().
These modules, including units distributed under the "Better Internet"
branding, use the same UART pin assignment and require the same
TX_FAULT/LOS behaviour and boot delay. Re-use the existing Potron
quirk for this EEPROM variant.
Signed-off-by: Marcus Hughes <marcus.hughes@betterinternet.ltd>
Link: https://patch.msgid.link/20251207210355.333451-1-marcus.hughes@betterinternet.ltd
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b5bdabb54 ]
The max buffer size of ENETC RX BD is 0xFFFF bytes, so if the PAGE_SIZE
is greater than 128K, ENETC_RXB_DMA_SIZE and ENETC_RXB_DMA_SIZE_XDP will
be greater than 0xFFFF, thus causing a build warning.
This will not cause any practical issues because ENETC is currently only
used on the ARM64 platform, and the max PAGE_SIZE is 64K. So this patch
is only for fixing the build warning that occurs when compiling ENETC
drivers for other platforms.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202601050637.kHEKKOG7-lkp@intel.com/
Fixes: e59bc32df2 ("net: enetc: correct the value of ENETC_RXB_TRUESIZE")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260107091204.1980222-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afa27621a2 ]
When asynchronously writing to the device registers and if usb_submit_urb()
fail, the code fail to release allocated to this point resources.
Fixes: 323b34963d ("drivers: net: usb: pegasus: fix control urb submission")
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Link: https://patch.msgid.link/20260106084821.3746677-1-petko.manolov@konsulko.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 333418872b ]
The NAN notification is for 5745 MHz which corresponds to channel 149
and not 5475 which is not actually a valid channel. This could result in
a NULL pointer dereference in cfg80211_next_nan_dw_notif.
Fixes: a37a6f5443 ("wifi: mac80211_hwsim: Add simulation support for NAN device")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260107143652.7dab2035836f.Iacbaf7bb94ed5c14a0928a625827e4137d8bfede@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6abcf751bc ]
airoha_ppe_deinit() runs airoha_npu_ppe_deinit() in atomic context.
airoha_npu_ppe_deinit routine allocates ppe_data buffer with GFP_KERNEL
flag. Rely on rcu_replace_pointer in airoha_ppe_deinit routine in order
to fix schedule while atomic issue in airoha_npu_ppe_deinit() since we
do not need atomic context there.
Fixes: 00a7678310 ("net: airoha: Introduce flowtable offload support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260105-airoha-fw-ethtool-v2-1-3b32b158cc31@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d83dddffe1 ]
This patch fixes the edge case behavior on ifup/ifdown and
linking/unlinking two netdevsim interfaces:
1. unlink two interfaces netdevsim1 and netdevsim2
2. ifdown netdevsim1
3. ifup netdevsim1
4. link two interfaces netdevsim1 and netdevsim2
5. (Now two interfaces are linked in terms of netdevsim peer, but
carrier state of the two interfaces remains DOWN.)
This inconsistent behavior is caused by the current implementation,
which only cares about the "link, then ifup" order, not "ifup, then
link" order. This patch fixes the inconsistency by calling
netif_carrier_on() when two netdevsim interfaces are linked.
This patch fixes buggy behavior on NetworkManager-based systems which
causes the netdevsim test to fail with the following error:
# timeout set to 600
# selftests: drivers/net/netdevsim: peer.sh
# 2025/12/25 00:54:03 socat[9115] W address is opened in read-write mode but only supports read-only
# 2025/12/25 00:56:17 socat[9115] W connect(7, AF=2 192.168.1.1:1234, 16): Connection timed out
# 2025/12/25 00:56:17 socat[9115] E TCP:192.168.1.1🔢 Connection timed out
# expected 3 bytes, got 0
# 2025/12/25 00:56:17 socat[9109] W exiting on signal 15
not ok 13 selftests: drivers/net/netdevsim: peer.sh # exit=1
This patch also solves timeout on TCP Fast Open (TFO) test in
NetworkManager-based systems because it also depends on netdevsim's
carrier consistency.
Fixes: 1a8fed52f7 ("netdevsim: set the carrier when the device goes up")
Signed-off-by: Yohei Kojima <yk@y-koj.net>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/602c9e1ba5bb2ee1997bb38b1d866c9c3b807ae9.1767624906.git.yk@y-koj.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13ff3e7242 ]
We expect the SFP write accessors to return the number of written bytes.
We fail to do so for single-byte smbus accesses, which may cause errors
when setting a module's high-power state and for some cotsworks modules.
Let's return the amount of written bytes, as expected.
Fixes: 7662abf4db ("net: phy: sfp: Add support for SMBus module access")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260105151840.144552-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7801edc9ba ]
This reverts commit 926eae6044, which
never could have produced the intended effect:
https://lore.kernel.org/netdev/AM0PR06MB10396BBF8B568D77556FC46F8F7DEA@AM0PR06MB10396.eurprd06.prod.outlook.com/
The reason why it is broken beyond repair in this form is that the
mv88e6xxx driver outsources its "tx-p2p-microvolt" property to the OF
node of an external Ethernet PHY. This:
(a) does not work if there is no external PHY (chip-to-chip connection,
or SFP module)
(b) pollutes the OF property namespace / bindings of said external PHY
("tx-p2p-microvolt" could have meaning for the Ethernet PHY's SerDes
interface as well)
We can revisit the idea of making SerDes amplitude configurable once we
have proper bindings for the mv88e6xxx SerDes. Until then, remove the
code that leaves us with unnecessary baggage.
Fixes: 926eae6044 ("dsa: mv88e6xxx: make serdes SGMII/Fiber tx amplitude configurable")
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260104093952.486606-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4648fb2f2e ]
If vport flags do not contain VIRTCHNL2_VPORT_ENABLE_RDMA, driver does not
allocate vdev_info for this vport. This leads to kernel NULL pointer
dereference in idpf_idc_vport_dev_down(), which references vdev_info for
every vport regardless.
Check, if vdev_info was ever allocated before unplugging aux device.
Fixes: be91128c57 ("idpf: implement RDMA vport auxiliary dev create, init, and destroy")
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 086efe0a1e ]
The HW only supports a maximum Rx buffer size of 16K-128. On systems
using large pages, the libeth logic can configure the buffer size to be
larger than this. The upper bound is PAGE_SIZE while the lower bound is
MTU rounded up to the nearest power of 2. For example, ARM systems with
a 64K page size and an mtu of 9000 will set the Rx buffer size to 16K,
which will cause the config Rx queues message to fail.
Initialize the bufq/fill queue buf_len field to the maximum supported
size. This will trigger the libeth logic to cap the maximum Rx buffer
size by reducing the upper bound.
Fixes: 74d1412ac8 ("idpf: use libeth Rx buffer management for payload buffer")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: David Decotigny <ddecotig@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b8ee6468 ]
Fix error handling to properly cleanup interrupts when
idpf_vport_queue_ids_init() or idpf_rx_bufs_init_all() fail. Jump to
'intr_deinit' instead of 'queues_rel' to ensure interrupts are cleaned up
before releasing other resources.
Fixes: d4d5587182 ("idpf: initialize interrupts and enable vport")
Signed-off-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebecca5b09 ]
During soft reset, the RSS LUT is freed and not restored unless the
interface is up. If an ethtool command that accesses the rss lut is
attempted immediately after reset, it will result in NULL ptr
dereference. Also, there is no need to reset the rss lut if the soft reset
does not involve queue count change.
After soft reset, set the RSS LUT to default values based on the updated
queue count only if the reset was a result of a queue count change and
the LUT was not configured by the user. In all other cases, don't touch
the LUT.
Steps to reproduce:
** Bring the interface down (if up)
ifconfig eth1 down
** update the queue count (eg., 27->20)
ethtool -L eth1 combined 20
** display the RSS LUT
ethtool -x eth1
[82375.558338] BUG: kernel NULL pointer dereference, address: 0000000000000000
[82375.558373] #PF: supervisor read access in kernel mode
[82375.558391] #PF: error_code(0x0000) - not-present page
[82375.558408] PGD 0 P4D 0
[82375.558421] Oops: Oops: 0000 [#1] SMP NOPTI
<snip>
[82375.558516] RIP: 0010:idpf_get_rxfh+0x108/0x150 [idpf]
[82375.558786] Call Trace:
[82375.558793] <TASK>
[82375.558804] rss_prepare.isra.0+0x187/0x2a0
[82375.558827] rss_prepare_data+0x3a/0x50
[82375.558845] ethnl_default_doit+0x13d/0x3e0
[82375.558863] genl_family_rcv_msg_doit+0x11f/0x180
[82375.558886] genl_rcv_msg+0x1ad/0x2b0
[82375.558902] ? __pfx_ethnl_default_doit+0x10/0x10
[82375.558920] ? __pfx_genl_rcv_msg+0x10/0x10
[82375.558937] netlink_rcv_skb+0x58/0x100
[82375.558957] genl_rcv+0x2c/0x50
[82375.558971] netlink_unicast+0x289/0x3e0
[82375.558988] netlink_sendmsg+0x215/0x440
[82375.559005] __sys_sendto+0x234/0x240
[82375.559555] __x64_sys_sendto+0x28/0x30
[82375.560068] x64_sys_call+0x1909/0x1da0
[82375.560576] do_syscall_64+0x7a/0xfa0
[82375.561076] ? clear_bhb_loop+0x60/0xb0
[82375.561567] entry_SYSCALL_64_after_hwframe+0x76/0x7e
<snip>
Fixes: 02cbfba1ad ("idpf: add ethtool callbacks")
Signed-off-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 445b49d137 ]
RSS LUT provisioning and queries on a down interface currently return
silently without effect. Users should be able to configure RSS settings
even when the interface is down.
Fix by maintaining RSS configuration changes in the driver's soft copy and
deferring HW programming until the interface comes up.
Fixes: 02cbfba1ad ("idpf: add ethtool callbacks")
Signed-off-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83f38f210b ]
The RSS LUT is not initialized until the interface comes up, causing
the following NULL pointer crash when ethtool operations like rxhash on/off
are performed before the interface is brought up for the first time.
Move RSS LUT initialization from ndo_open to vport creation to ensure LUT
is always available. This enables RSS configuration via ethtool before
bringing the interface up. Simplify LUT management by maintaining all
changes in the driver's soft copy and programming zeros to the indirection
table when rxhash is disabled. Defer HW programming until the interface
comes up if it is down during rxhash and LUT configuration changes.
Steps to reproduce:
** Load idpf driver; interfaces will be created
modprobe idpf
** Before bringing the interfaces up, turn rxhash off
ethtool -K eth2 rxhash off
[89408.371875] BUG: kernel NULL pointer dereference, address: 0000000000000000
[89408.371908] #PF: supervisor read access in kernel mode
[89408.371924] #PF: error_code(0x0000) - not-present page
[89408.371940] PGD 0 P4D 0
[89408.371953] Oops: Oops: 0000 [#1] SMP NOPTI
<snip>
[89408.372052] RIP: 0010:memcpy_orig+0x16/0x130
[89408.372310] Call Trace:
[89408.372317] <TASK>
[89408.372326] ? idpf_set_features+0xfc/0x180 [idpf]
[89408.372363] __netdev_update_features+0x295/0xde0
[89408.372384] ethnl_set_features+0x15e/0x460
[89408.372406] genl_family_rcv_msg_doit+0x11f/0x180
[89408.372429] genl_rcv_msg+0x1ad/0x2b0
[89408.372446] ? __pfx_ethnl_set_features+0x10/0x10
[89408.372465] ? __pfx_genl_rcv_msg+0x10/0x10
[89408.372482] netlink_rcv_skb+0x58/0x100
[89408.372502] genl_rcv+0x2c/0x50
[89408.372516] netlink_unicast+0x289/0x3e0
[89408.372533] netlink_sendmsg+0x215/0x440
[89408.372551] __sys_sendto+0x234/0x240
[89408.372571] __x64_sys_sendto+0x28/0x30
[89408.372585] x64_sys_call+0x1909/0x1da0
[89408.372604] do_syscall_64+0x7a/0xfa0
[89408.373140] ? clear_bhb_loop+0x60/0xb0
[89408.373647] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[89408.378887] </TASK>
<snip>
Fixes: a251eee621 ("idpf: add SRIOV support and other ndo_ops")
Signed-off-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36aae2ea6b ]
When ethtool -n is executed on an interface to display the flow steering
rules, "rxclass: Unknown flow type" error is generated.
The flow steering list maintained in the driver currently stores only the
location and q_index but other fields of the ethtool_rx_flow_spec are not
stored. This may be enough for the virtchnl command to delete the entry.
However, when the ethtool -n command is used to query the flow steering
rules, the ethtool_rx_flow_spec returned is not complete causing the
error below.
Resolve this by storing the flow spec (fsp) when rules are added and
returning the complete flow spec when rules are queried.
Also, change the return value from EINVAL to ENOENT when flow steering
entry is not found during query by location or when deleting an entry.
Add logic to detect and reject duplicate filter entries at the same
location and change logic to perform upfront validation of all error
conditions before adding flow rules through virtchnl. This avoids the
need for additional virtchnl delete messages when subsequent operations
fail, which was missing in the original upstream code.
Example:
Before the fix:
ethtool -n eth1
2 RX rings available
Total 2 rules
rxclass: Unknown flow type
rxclass: Unknown flow type
After the fix:
ethtool -n eth1
2 RX rings available
Total 2 rules
Filter: 0
Rule Type: TCP over IPv4
Src IP addr: 10.0.0.1 mask: 0.0.0.0
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
Action: Direct to queue 0
Filter: 1
Rule Type: UDP over IPv4
Src IP addr: 10.0.0.1 mask: 0.0.0.0
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
Action: Direct to queue 0
Fixes: ada3e24b84 ("idpf: add flow steering support")
Signed-off-by: Erik Gabriel Carrillo <erik.g.carrillo@intel.com>
Co-developed-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Signed-off-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9841bd28b ]
The flow steering list maintains entries that are added and removed as
ethtool creates and deletes flow steering rules. Module removal with active
entries causes memory leak as the list is not properly cleaned up.
Prevent this by iterating through the remaining entries in the list and
freeing the associated memory during module removal. Add a spinlock
(flow_steer_list_lock) to protect the list access from multiple threads.
Fixes: ada3e24b84 ("idpf: add flow steering support")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d792219fe ]
If the init_task fails during a driver load, we end up without vports and
netdevs, effectively failing the entire process. In that state a
subsequent reset will result in a crash as the service task attempts to
access uninitialized resources. Following trace is from an error in the
init_task where the CREATE_VPORT (op 501) is rejected by the FW:
[40922.763136] idpf 0000:83:00.0: Device HW Reset initiated
[40924.449797] idpf 0000:83:00.0: Transaction failed (op 501)
[40958.148190] idpf 0000:83:00.0: HW reset detected
[40958.161202] BUG: kernel NULL pointer dereference, address: 00000000000000a8
...
[40958.168094] Workqueue: idpf-0000:83:00.0-vc_event idpf_vc_event_task [idpf]
[40958.168865] RIP: 0010:idpf_vc_event_task+0x9b/0x350 [idpf]
...
[40958.177932] Call Trace:
[40958.178491] <TASK>
[40958.179040] process_one_work+0x226/0x6d0
[40958.179609] worker_thread+0x19e/0x340
[40958.180158] ? __pfx_worker_thread+0x10/0x10
[40958.180702] kthread+0x10f/0x250
[40958.181238] ? __pfx_kthread+0x10/0x10
[40958.181774] ret_from_fork+0x251/0x2b0
[40958.182307] ? __pfx_kthread+0x10/0x10
[40958.182834] ret_from_fork_asm+0x1a/0x30
[40958.183370] </TASK>
Fix the error handling in the init_task to make sure the service and
mailbox tasks are disabled if the error happens during load. These are
started in idpf_vc_core_init(), which spawns the init_task and has no way
of knowing if it failed. If the error happens on reset, following
successful driver load, the tasks can still run, as that will allow the
netdevs to attempt recovery through another reset. Stop the PTP callbacks
either way as those will be restarted by the call to idpf_vc_core_init()
during a successful reset.
Fixes: 0fe45467a1 ("idpf: add create vport and netdev configuration")
Reported-by: Vivek Kumar <iamvivekkumar@google.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e281e1155 ]
Protect the reset path from callbacks by setting the netdevs to detached
state and close any netdevs in UP state until the reset handling has
completed. During a reset, the driver will de-allocate resources for the
vport, and there is no guarantee that those will recover, which is why the
existing vport_ctrl_lock does not provide sufficient protection.
idpf_detach_and_close() is called right before reset handling. If the
reset handling succeeds, the netdevs state is recovered via call to
idpf_attach_and_open(). If the reset handling fails the netdevs remain
down. The detach/down calls are protected with RTNL lock to avoid racing
with callbacks. On the recovery side the attach can be done without
holding the RTNL lock as there are no callbacks expected at that point,
due to detach/close always being done first in that flow.
The previous logic restoring the netdevs state based on the
IDPF_VPORT_UP_REQUESTED flag in the init task is not needed anymore, hence
the removal of idpf_set_vport_state(). The IDPF_VPORT_UP_REQUESTED is
still being used to restore the state of the netdevs following the reset,
but has no use outside of the reset handling flow.
idpf_init_hard_reset() is converted to void, since it was used as such and
there is no error handling being done based on its return value.
Before this change, invoking hard and soft resets simultaneously will
cause the driver to lose the vport state:
ip -br a
<inf> UP
echo 1 > /sys/class/net/ens801f0/device/reset& \
ethtool -L ens801f0 combined 8
ip -br a
<inf> DOWN
ip link set <inf> up
ip -br a
<inf> DOWN
Also in case of a failure in the reset path, the netdev is left
exposed to external callbacks, while vport resources are not
initialized, leading to a crash on subsequent ifup/down:
[408471.398966] idpf 0000:83:00.0: HW reset detected
[408471.411744] idpf 0000:83:00.0: Device HW Reset initiated
[408472.277901] idpf 0000:83:00.0: The driver was unable to contact the device's firmware. Check that the FW is running. Driver state= 0x2
[408508.125551] BUG: kernel NULL pointer dereference, address: 0000000000000078
[408508.126112] #PF: supervisor read access in kernel mode
[408508.126687] #PF: error_code(0x0000) - not-present page
[408508.127256] PGD 2aae2f067 P4D 0
[408508.127824] Oops: Oops: 0000 [#1] SMP NOPTI
...
[408508.130871] RIP: 0010:idpf_stop+0x39/0x70 [idpf]
...
[408508.139193] Call Trace:
[408508.139637] <TASK>
[408508.140077] __dev_close_many+0xbb/0x260
[408508.140533] __dev_change_flags+0x1cf/0x280
[408508.140987] netif_change_flags+0x26/0x70
[408508.141434] dev_change_flags+0x3d/0xb0
[408508.141878] devinet_ioctl+0x460/0x890
[408508.142321] inet_ioctl+0x18e/0x1d0
[408508.142762] ? _copy_to_user+0x22/0x70
[408508.143207] sock_do_ioctl+0x3d/0xe0
[408508.143652] sock_ioctl+0x10e/0x330
[408508.144091] ? find_held_lock+0x2b/0x80
[408508.144537] __x64_sys_ioctl+0x96/0xe0
[408508.144979] do_syscall_64+0x79/0x3d0
[408508.145415] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[408508.145860] RIP: 0033:0x7f3e0bb4caff
Fixes: 0fe45467a1 ("idpf: add create vport and netdev configuration")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dd72ebc73 ]
Convert vport state to a bitmap and remove the DOWN state which is
redundant in the existing logic. There are no functional changes aside
from the use of bitwise operations when setting and checking the states.
Removed the double underscore to be consistent with the naming of other
bitmaps in the header and renamed current_state to vport_is_up to match
the meaning of the new variable.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Chittim Madhu <madhu.chittim@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251125223632.1857532-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 2e281e1155 ("idpf: detach and close netdevs while handling a reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 083029bd8b ]
During a successful reset the driver would re-allocate vport resources
while keeping the netdevs intact. However, in case of an error in the
init task, the netdev of the failing vport will be unregistered,
effectively removing the network interface:
[ 121.211076] idpf 0000:83:00.0: enabling device (0100 -> 0102)
[ 121.221976] idpf 0000:83:00.0: Device HW Reset initiated
[ 124.161229] idpf 0000:83:00.0 ens801f0: renamed from eth0
[ 124.163364] idpf 0000:83:00.0 ens801f0d1: renamed from eth1
[ 125.934656] idpf 0000:83:00.0 ens801f0d2: renamed from eth2
[ 128.218429] idpf 0000:83:00.0 ens801f0d3: renamed from eth3
ip -br a
ens801f0 UP
ens801f0d1 UP
ens801f0d2 UP
ens801f0d3 UP
echo 1 > /sys/class/net/ens801f0/device/reset
[ 145.885537] idpf 0000:83:00.0: resetting
[ 145.990280] idpf 0000:83:00.0: reset done
[ 146.284766] idpf 0000:83:00.0: HW reset detected
[ 146.296610] idpf 0000:83:00.0: Device HW Reset initiated
[ 211.556719] idpf 0000:83:00.0: Transaction timed-out (op:526 cookie:7700 vc_op:526 salt:77 timeout:60000ms)
[ 272.996705] idpf 0000:83:00.0: Transaction timed-out (op:502 cookie:7800 vc_op:502 salt:78 timeout:60000ms)
ip -br a
ens801f0d1 DOWN
ens801f0d2 DOWN
ens801f0d3 DOWN
Re-shuffle the logic in the error path of the init task to make sure the
netdevs remain intact. This will allow the driver to attempt recovery via
subsequent resets, provided the FW is still functional.
The main change is to make sure that idpf_decfg_netdev() is not called
should the init task fail during a reset. The error handling is
consolidated under unwind_vports, as the removed labels had the same
cleanup logic split depending on the point of failure.
Fixes: ce1b75d063 ("idpf: add ptypes and MAC filter support")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffeafa65b2 ]
Fix the max number of bits passed to find_first_zero_bit() in
bnxt_alloc_agg_idx(). We were incorrectly passing the number of
long words. find_first_zero_bit() may fail to find a zero bit and
cause a wrong ID to be used. If the wrong ID is already in use, this
can cause data corruption. Sometimes an error like this can also be
seen:
bnxt_en 0000:83:00.0 enp131s0np0: TPA end agg_buf 2 != expected agg_bufs 1
Fix it by passing the correct number of bits MAX_TPA_P5. Use
DECLARE_BITMAP() to more cleanly define the bitmap. Add a sanity
check to warn if a bit cannot be found and reset the ring [MChan].
Fixes: ec4d8e7cf0 ("bnxt_en: Add TPA ID mapping logic for 57500 chips.")
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Srijit Bose <srijit.bose@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251231083625.3911652-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92e6e0a87f ]
Commit 1f52d7b622 ("net: wwan: iosm: Enable M.2 7360 WWAN card support")
allocated memory for pp_qlt in ipc_mux_init() but did not free it in
ipc_mux_deinit(). This results in a memory leak when the driver is
unloaded.
Free the allocated memory in ipc_mux_deinit() to fix the leak.
Fixes: 1f52d7b622 ("net: wwan: iosm: Enable M.2 7360 WWAN card support")
Co-developed-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20251230071853.1062223-1-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0462a15d2d ]
The commit which added RX steering rules for PSP forgot to free a modify
header HW object on the cleanup path, which lead to health errors when
reloading the driver and uninitializing the device:
mlx5_core 0000:08:00.0: poll_health:803:(pid 3021): Fatal error 3 detected
Fix that by saving the modify header pointer in the PSP steering struct
and deallocating it after freeing the rule which references it.
Fixes: 9536fbe10c ("net/mlx5e: Add PSP steering in local NIC RX")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20251225132717.358820-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 144297e2a2 ]
Dumping module EEPROM on newer modules is supported through the netlink
interface only.
Querying with old userspace ethtool (or other tools, such as 'lshw')
which still uses the ioctl interface results in an error message that
could flood dmesg (in addition to the expected error return value).
The original message was added under the assumption that the driver
should be able to handle all module types, but now that such flows are
easily triggered from userspace, it doesn't serve its purpose.
Change the log level of the print in mlx5_query_module_eeprom() to
debug.
Fixes: bb64143eee ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20251225132717.358820-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c75dc9de4 ]
Currently, the ppcnt_statistical_group capability check
incorrectly gates access to FEC histogram statistics.
This capability applies only to statistical and physical
counter groups, not for histogram data.
Restrict the ppcnt_statistical_group check to the
Physical_Layer_Counters and Physical_Layer_Statistical_Counters
groups.
Histogram statistics access remains gated by the pphcr
capability.
The issue is harmless as of today, as it happens that
ppcnt_statistical_group is set on all existing devices that
have pphcr set.
Fixes: 6b81b8a0b1 ("net/mlx5e: Don't query FEC statistics when FEC is disabled")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20251225132717.358820-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31057979cd ]
Today multipath offload is controlled by a single route and the route
controlling is selected if it meets one of the following criteria:
1. No controlling route is set.
2. New route destination is the same as old one.
3. New route metric is lower than old route metric.
This can cause unwanted behaviour in case a new route is added
with a smaller network prefix which should get the priority.
Fix this by adding a new criteria to give priority to new route with
a smaller network prefix.
Fixes: ad11c4f1d8 ("net/mlx5e: Lag, Only handle events from highest priority multipath entry")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20251225132717.358820-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62f7edd599 ]
Implement soft_reset, suspend, and resume callbacks using
genphy_soft_reset(), genphy_suspend(), and genphy_resume()
to fix PHY initialization and power management issues.
The soft_reset callback is needed to properly recover the PHY after an
ifconfig down/up cycle. Without it, the PHY can remain in power-down
state, causing MDIO register access failures during config_init().
The soft reset ensures the PHY is operational before configuration.
The suspend/resume callbacks enable proper power management during
system suspend/resume cycles.
Fixes: b2908a989c ("net: phy: add driver for MaxLinear MxL86110 PHY")
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Link: https://patch.msgid.link/20251223120940.407195-1-stefano.r@variscite.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34f3ff52cb ]
Commit 15faa1f67a ("lan966x: Fix crash when adding interface under a lag")
fixed a similar issue in the lan966x driver caused by a NULL pointer dereference.
The ocelot_set_aggr_pgids() function in the ocelot driver has similar logic
and is susceptible to the same crash.
This issue specifically affects the ocelot_vsc7514.c frontend, which leaves
unused ports as NULL pointers. The felix_vsc9959.c frontend is unaffected as
it uses the DSA framework which registers all ports.
Fix this by checking if the port pointer is valid before accessing it.
Fixes: 528d3f190c ("net: mscc: ocelot: drop the use of the "lags" array")
Signed-off-by: Jerry Wu <w.7erry@foxmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/tencent_75EF812B305E26B0869C673DD1160866C90A@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a428e0da12 ]
devlink_alloc() may return NULL on allocation failure, but
prestera_devlink_alloc() unconditionally calls devlink_priv() on
the returned pointer.
This leads to a NULL pointer dereference if devlink allocation fails.
Add a check for a NULL devlink pointer and return NULL early to avoid
the crash.
Fixes: 34dd1710f5 ("net: marvell: prestera: Add basic devlink support")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Acked-by: Elad Nachman <enachman@marvell.com>
Link: https://patch.msgid.link/20251230052124.897012-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3358995b1a upstream.
When bnxt_init_one() fails during initialization (e.g.,
bnxt_init_int_mode returns -ENODEV), the error path calls
bnxt_free_hwrm_resources() which destroys the DMA pool and sets
bp->hwrm_dma_pool to NULL. Subsequently, bnxt_ptp_clear() is called,
which invokes ptp_clock_unregister().
Since commit a60fc3294a ("ptp: rework ptp_clock_unregister() to
disable events"), ptp_clock_unregister() now calls
ptp_disable_all_events(), which in turn invokes the driver's .enable()
callback (bnxt_ptp_enable()) to disable PTP events before completing the
unregistration.
bnxt_ptp_enable() attempts to send HWRM commands via bnxt_ptp_cfg_pin()
and bnxt_ptp_cfg_event(), both of which call hwrm_req_init(). This
function tries to allocate from bp->hwrm_dma_pool, causing a NULL
pointer dereference:
bnxt_en 0000:01:00.0 (unnamed net_device) (uninitialized): bnxt_init_int_mode err: ffffffed
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
Call Trace:
__hwrm_req_init (drivers/net/ethernet/broadcom/bnxt/bnxt_hwrm.c:72)
bnxt_ptp_enable (drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:323 drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:517)
ptp_disable_all_events (drivers/ptp/ptp_chardev.c:66)
ptp_clock_unregister (drivers/ptp/ptp_clock.c:518)
bnxt_ptp_clear (drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:1134)
bnxt_init_one (drivers/net/ethernet/broadcom/bnxt/bnxt.c:16889)
Lines are against commit f8f9c1f4d0 ("Linux 6.19-rc3")
Fix this by clearing and unregistering ptp (bnxt_ptp_clear()) before
freeing HWRM resources.
Suggested-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: a60fc3294a ("ptp: rework ptp_clock_unregister() to disable events")
Cc: stable@vger.kernel.org
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260106-bnxt-v3-1-71f37e11446a@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4e305ed60 upstream.
pdev can be null and free_ring: can be called in 1297 with a null
pdev.
Fixes: 55c82617c3 ("3c59x: convert to generic DMA API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Link: https://patch.msgid.link/20260106094731.25819-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99537d5c47 upstream.
In the non-RT kernel, local_bh_disable() merely disables preemption,
whereas it maps to an actual spin lock in the RT kernel. Consequently,
when attempting to refill RX buffers via netdev_alloc_skb() in
macb_mac_link_up(), a deadlock scenario arises as follows:
WARNING: possible circular locking dependency detected
6.18.0-08691-g2061f18ad76e #39 Not tainted
------------------------------------------------------
kworker/0:0/8 is trying to acquire lock:
ffff00080369bbe0 (&bp->lock){+.+.}-{3:3}, at: macb_start_xmit+0x808/0xb7c
but task is already holding lock:
ffff000803698e58 (&queue->tx_ptr_lock){+...}-{3:3}, at: macb_start_xmit
+0x148/0xb7c
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&queue->tx_ptr_lock){+...}-{3:3}:
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x148/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #2 (_xmit_ETHER#2){+...}-{3:3}:
rt_spin_lock+0x50/0x1f0
sch_direct_xmit+0x11c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #1 ((softirq_ctrl.lock)){+.+.}-{3:3}:
lock_release+0x250/0x348
__local_bh_enable_ip+0x7c/0x240
__netdev_alloc_skb+0x1b4/0x1d8
gem_rx_refill+0xdc/0x240
gem_init_rings+0xb4/0x108
macb_mac_link_up+0x9c/0x2b4
phylink_resolve+0x170/0x614
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #0 (&bp->lock){+.+.}-{3:3}:
__lock_acquire+0x15a8/0x2084
lock_acquire+0x1cc/0x350
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x808/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
other info that might help us debug this:
Chain exists of:
&bp->lock --> _xmit_ETHER#2 --> &queue->tx_ptr_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&queue->tx_ptr_lock);
lock(_xmit_ETHER#2);
lock(&queue->tx_ptr_lock);
lock(&bp->lock);
*** DEADLOCK ***
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0xa0/0xf0
dump_stack+0x18/0x24
print_circular_bug+0x28c/0x370
check_noncircular+0x198/0x1ac
__lock_acquire+0x15a8/0x2084
lock_acquire+0x1cc/0x350
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x808/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
Notably, invoking the mog_init_rings() callback upon link establishment
is unnecessary. Instead, we can exclusively call mog_init_rings() within
the ndo_open() callback. This adjustment resolves the deadlock issue.
Furthermore, since MACB_CAPS_MACB_IS_EMAC cases do not use mog_init_rings()
when opening the network interface via at91ether_open(), moving
mog_init_rings() to macb_open() also eliminates the MACB_CAPS_MACB_IS_EMAC
check.
Fixes: 633e98a711 ("net: macb: use resolved link config in mac_link_up()")
Cc: stable@vger.kernel.org
Suggested-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://patch.msgid.link/20251222015624.1994551-1-xiaolei.wang@windriver.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e5a541420 upstream.
When nvmem_cell_read() fails in mt798x_phy_calibration(), the function
returns without calling nvmem_cell_put(), leaking the cell reference.
Move nvmem_cell_put() right after nvmem_cell_read() to ensure the cell
reference is always released regardless of the read result.
Found via static analysis and code review.
Fixes: 98c485eaf5 ("net: phy: add driver for MediaTek SoC built-in GE PHYs")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251211081313.2368460-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa0b198be1 upstream.
This fixes the device failing to initialize with "error reading MAC
address" for me, probably because the incorrect write of NCR_RST to
SR_NCR is not actually resetting the device.
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Cc: stable@vger.kernel.org
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20251221082400.50688-1-enelsonmoore@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d970eda00 upstream.
Currently, interrupts are automatically enabled immediately upon
request. This allows interrupt to fire before the associated NAPI
context is fully initialized and cause failures like below:
[ 0.946369] Call Trace:
[ 0.946369] <IRQ>
[ 0.946369] __napi_poll+0x2a/0x1e0
[ 0.946369] net_rx_action+0x2f9/0x3f0
[ 0.946369] handle_softirqs+0xd6/0x2c0
[ 0.946369] ? handle_edge_irq+0xc1/0x1b0
[ 0.946369] __irq_exit_rcu+0xc3/0xe0
[ 0.946369] common_interrupt+0x81/0xa0
[ 0.946369] </IRQ>
[ 0.946369] <TASK>
[ 0.946369] asm_common_interrupt+0x22/0x40
[ 0.946369] RIP: 0010:pv_native_safe_halt+0xb/0x10
Use the `IRQF_NO_AUTOEN` flag when requesting interrupts to prevent auto
enablement and explicitly enable the interrupt in NAPI initialization
path (and disable it during NAPI teardown).
This ensures that interrupt lifecycle is strictly coupled with
readiness of NAPI context.
Cc: stable@vger.kernel.org
Fixes: 1dfc2e4611 ("gve: Refactor napi add and remove functions")
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20251219102945.2193617-1-hramamurthy@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15ef641a0c upstream.
In error paths, add fjes_hw_iounmap() to release the
resource acquired by fjes_hw_iomap(). Add a goto label
to do so.
Fixes: 8cdc3f6c5d ("fjes: Hardware initialization routine")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251211073756.101824-1-lihaoxiang@isrc.iscas.ac.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c72a5182e upstream.
In e1000_tbi_should_accept() we read the last byte of the frame via
'data[length - 1]' to evaluate the TBI workaround. If the descriptor-
reported length is zero or larger than the actual RX buffer size, this
read goes out of bounds and can hit unrelated slab objects. The issue
is observed from the NAPI receive path (e1000_clean_rx_irq):
==================================================================
BUG: KASAN: slab-out-of-bounds in e1000_tbi_should_accept+0x610/0x790
Read of size 1 at addr ffff888014114e54 by task sshd/363
CPU: 0 PID: 363 Comm: sshd Not tainted 5.18.0-rc1 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x5a/0x74
print_address_description+0x7b/0x440
print_report+0x101/0x200
kasan_report+0xc1/0xf0
e1000_tbi_should_accept+0x610/0x790
e1000_clean_rx_irq+0xa8c/0x1110
e1000_clean+0xde2/0x3c10
__napi_poll+0x98/0x380
net_rx_action+0x491/0xa20
__do_softirq+0x2c9/0x61d
do_softirq+0xd1/0x120
</IRQ>
<TASK>
__local_bh_enable_ip+0xfe/0x130
ip_finish_output2+0x7d5/0xb00
__ip_queue_xmit+0xe24/0x1ab0
__tcp_transmit_skb+0x1bcb/0x3340
tcp_write_xmit+0x175d/0x6bd0
__tcp_push_pending_frames+0x7b/0x280
tcp_sendmsg_locked+0x2e4f/0x32d0
tcp_sendmsg+0x24/0x40
sock_write_iter+0x322/0x430
vfs_write+0x56c/0xa60
ksys_write+0xd1/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f511b476b10
Code: 73 01 c3 48 8b 0d 88 d3 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d f9 2b 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 8e 9b 01 00 48 89 04 24
RSP: 002b:00007ffc9211d4e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000004024 RCX: 00007f511b476b10
RDX: 0000000000004024 RSI: 0000559a9385962c RDI: 0000000000000003
RBP: 0000559a9383a400 R08: fffffffffffffff0 R09: 0000000000004f00
R10: 0000000000000070 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffc9211d57f R14: 0000559a9347bde7 R15: 0000000000000003
</TASK>
Allocated by task 1:
__kasan_krealloc+0x131/0x1c0
krealloc+0x90/0xc0
add_sysfs_param+0xcb/0x8a0
kernel_add_sysfs_param+0x81/0xd4
param_sysfs_builtin+0x138/0x1a6
param_sysfs_init+0x57/0x5b
do_one_initcall+0x104/0x250
do_initcall_level+0x102/0x132
do_initcalls+0x46/0x74
kernel_init_freeable+0x28f/0x393
kernel_init+0x14/0x1a0
ret_from_fork+0x22/0x30
The buggy address belongs to the object at ffff888014114000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1620 bytes to the right of
2048-byte region [ffff888014114000, ffff888014114800]
The buggy address belongs to the physical page:
page:ffffea0000504400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x14110
head:ffffea0000504400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x100000000010200(slab|head|node=0|zone=1)
raw: 0100000000010200 0000000000000000 dead000000000001 ffff888013442000
raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
==================================================================
This happens because the TBI check unconditionally dereferences the last
byte without validating the reported length first:
u8 last_byte = *(data + length - 1);
Fix by rejecting the frame early if the length is zero, or if it exceeds
adapter->rx_buffer_len. This preserves the TBI workaround semantics for
valid frames and prevents touching memory beyond the RX buffer.
Fixes: 2037110c96 ("e1000: move tbi workaround code into helper function")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca58982229 upstream.
On my system the arithmetic done on the firmware numbers
results in a negative number, but since the types are
unsigned it gets interpreted as a large positive number.
The end result is that the firmware gets rejected and wifi
is defunct.
Switch to signed types to handle this case correctly.
iwlwifi 0000:0c:00.0: Driver unable to support your firmware API. Driver supports FW core 4294967294..2, firmware is 2.
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-4.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-3.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-2.ucode failed with error -2
iwlwifi 0000:0c:00.0: Direct firmware load for iwlwifi-5000-1.ucode failed with error -2
iwlwifi 0000:0c:00.0: no suitable firmware found!
iwlwifi 0000:0c:00.0: minimum version required: iwlwifi-5000-1
iwlwifi 0000:0c:00.0: maximum version supported: iwlwifi-5000-5
iwlwifi 0000:0c:00.0: check git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
Cc: stable@vger.kernel.org
Fixes: 5f708cccde ("wifi: iwlwifi: add a new FW file numbering scheme")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220805
Link: https://patch.msgid.link/20251113222852.15896-1-ville.syrjala@linux.intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a48e232210 ]
There is a crash issue when running zero copy XDP_TX action, the crash
log is shown below.
[ 216.122464] Unable to handle kernel paging request at virtual address fffeffff80000000
[ 216.187524] Internal error: Oops: 0000000096000144 [#1] SMP
[ 216.301694] Call trace:
[ 216.304130] dcache_clean_poc+0x20/0x38 (P)
[ 216.308308] __dma_sync_single_for_device+0x1bc/0x1e0
[ 216.313351] stmmac_xdp_xmit_xdpf+0x354/0x400
[ 216.317701] __stmmac_xdp_run_prog+0x164/0x368
[ 216.322139] stmmac_napi_poll_rxtx+0xba8/0xf00
[ 216.326576] __napi_poll+0x40/0x218
[ 216.408054] Kernel panic - not syncing: Oops: Fatal exception in interrupt
For XDP_TX action, the xdp_buff is converted to xdp_frame by
xdp_convert_buff_to_frame(). The memory type of the resulting xdp_frame
depends on the memory type of the xdp_buff. For page pool based xdp_buff
it produces xdp_frame with memory type MEM_TYPE_PAGE_POOL. For zero copy
XSK pool based xdp_buff it produces xdp_frame with memory type
MEM_TYPE_PAGE_ORDER0. However, stmmac_xdp_xmit_back() does not check the
memory type and always uses the page pool type, this leads to invalid
mappings and causes the crash. Therefore, check the xdp_buff memory type
in stmmac_xdp_xmit_back() to fix this issue.
Fixes: bba2556efa ("net: stmmac: Enable RX via AF_XDP zero-copy")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20251204071332.1907111-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85f4b0c650 ]
This patch ensures that the RX ring size (rx_pending) is not
set below the permitted length. This avoids UBSAN
shift-out-of-bounds errors when users passes small or zero
ring sizes via ethtool -G.
Fixes: d45d897984 ("octeontx2-pf: Add basic ethtool support")
Signed-off-by: Anshumali Gaur <agaur@marvell.com>
Link: https://patch.msgid.link/20251219062226.524844-1-agaur@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4f800c448 ]
Currently in the return path, fwnode_handle_put calls are missing. Just use
_scoped to avoid the issue.
Fixes: 24e31e4747 ("net: mdio: Add RTL9300 MDIO driver")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20251217210153.14641-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d42bce414d ]
port_fdb_dump() is supposed to only add fdb entries, but we iterate over
the full ARL table, which also includes multicast entries.
So check if the entry is a multicast entry before passing it on to the
callback().
Additionally, the port of those entries is a bitmask, not a port number,
so any included entries would have even be for the wrong port.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251217205756.172123-1-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b94f11af9d ]
The LIBWX library code is what calls into phylink, so any user of
it has to select CONFIG_PHYLINK at the moment, with NGBEVF missing this:
x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_nway_reset':
wx_ethtool.c:(.text+0x613): undefined reference to `phylink_ethtool_nway_reset'
x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_get_link_ksettings':
wx_ethtool.c:(.text+0x62b): undefined reference to `phylink_ethtool_ksettings_get'
x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_set_link_ksettings':
wx_ethtool.c:(.text+0x643): undefined reference to `phylink_ethtool_ksettings_set'
x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_get_pauseparam':
wx_ethtool.c:(.text+0x65b): undefined reference to `phylink_ethtool_get_pauseparam'
x86_64-linux-ld: drivers/net/ethernet/wangxun/libwx/wx_ethtool.o: in function `wx_set_pauseparam':
wx_ethtool.c:(.text+0x677): undefined reference to `phylink_ethtool_set_pauseparam'
Add the 'select PHYLINK' line in the libwx option directly so this will
always be enabled for all current and future wangxun drivers, and remove
the now duplicate lines.
Fixes: a0008a3658 ("net: wangxun: add ngbevf build")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251216213547.115026-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
