There are currently two situations that can trigger the PTP interrupt,
one is the PPS event, the other is the PEROUT event. However, the irq
handler fec_pps_interrupt() does not check the irq event type and
directly registers a PPS event into the system, but the event may be
a PEROUT event. This is incorrect because PEROUT is an output signal,
while PPS is the input of the kernel PPS system. Therefore, add a check
for the event type, if pps_enable is true, it means that the current
event is a PPS event, and then the PPS event is registered.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-5-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the current driver, PPS and PEROUT use the same channel to generate
the events, so they cannot be enabled at the same time. Otherwise, the
later configuration will overwrite the earlier configuration. Therefore,
when configuring PPS, the driver will check whether PEROUT is enabled.
Similarly, when configuring PEROUT, the driver will check whether PPS
is enabled.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-4-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If the previously set PEROUT is already active, updating it will cause
the new PEROUT to start immediately instead of at the specified time.
This is because fep->reload_period is updated whithout check whether
the PEROUT is enabled, and the old PEROUT is not disabled. Therefore,
the pulse period will be updated immediately in the pulse interrupt
handler fec_pps_interrupt().
Currently, the driver does not support directly updating PEROUT and it
will make the logic be more complicated. To fix the current issue, add
a check before enabling the PEROUT, the driver will return an error if
PEROUT is enabled. If users wants to update a new PEROUT, they should
disable the old PEROUT first.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The PEROUT allows the user to set a specified future time to output the
periodic signal. If the future time is far from the current time, the FEC
driver will use hrtimer to configure PEROUT one second before the future
time. However, the hrtimer will not be canceled if the PEROUT is disabled
before the hrtimer expires. So the PEROUT will be configured when the
hrtimer expires, which is not as expected. Therefore, cancel the hrtimer
in fec_ptp_pps_disable() to fix this issue.
Fixes: 350749b909 ("net: fec: Add support for periodic output signal of PPS")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251125085210.1094306-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The atlantic driver can receive packets with more than MAX_SKB_FRAGS (17)
fragments when handling large multi-descriptor packets. This causes an
out-of-bounds write in skb_add_rx_frag_netmem() leading to kernel panic.
The issue occurs because the driver doesn't check the total number of
fragments before calling skb_add_rx_frag(). When a packet requires more
than MAX_SKB_FRAGS fragments, the fragment index exceeds the array bounds.
Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE,
then all fragments are accounted for. And reusing the existing check to
prevent the overflow earlier in the code path.
This crash occurred in production with an Aquantia AQC113 10G NIC.
Stack trace from production environment:
```
RIP: 0010:skb_add_rx_frag_netmem+0x29/0xd0
Code: 90 f3 0f 1e fa 0f 1f 44 00 00 48 89 f8 41 89
ca 48 89 d7 48 63 ce 8b 90 c0 00 00 00 48 c1 e1 04 48 01 ca 48 03 90
c8 00 00 00 <48> 89 7a 30 44 89 52 3c 44 89 42 38 40 f6 c7 01 75 74 48
89 fa 83
RSP: 0018:ffffa9bec02a8d50 EFLAGS: 00010287
RAX: ffff925b22e80a00 RBX: ffff925ad38d2700 RCX:
fffffffe0a0c8000
RDX: ffff9258ea95bac0 RSI: ffff925ae0a0c800 RDI:
0000000000037a40
RBP: 0000000000000024 R08: 0000000000000000 R09:
0000000000000021
R10: 0000000000000848 R11: 0000000000000000 R12:
ffffa9bec02a8e24
R13: ffff925ad8615570 R14: 0000000000000000 R15:
ffff925b22e80a00
FS: 0000000000000000(0000)
GS:ffff925e47880000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9258ea95baf0 CR3: 0000000166022004 CR4:
0000000000f72ef0
PKRU: 55555554
Call Trace:
<IRQ>
aq_ring_rx_clean+0x175/0xe60 [atlantic]
? aq_ring_rx_clean+0x14d/0xe60 [atlantic]
? aq_ring_tx_clean+0xdf/0x190 [atlantic]
? kmem_cache_free+0x348/0x450
? aq_vec_poll+0x81/0x1d0 [atlantic]
? __napi_poll+0x28/0x1c0
? net_rx_action+0x337/0x420
```
Fixes: 6aecbba12b ("net: atlantic: add check for MAX_SKB_FRAGS")
Changes in v4:
- Add Fixes: tag to satisfy patch validation requirements.
Changes in v3:
- Fix by assuming there will be an extra frag if buff->len > AQ_CFG_RX_HDR_SIZE,
then all fragments are accounted for.
Signed-off-by: Jiefeng Zhang <jiefeng.z.zhang@gmail.com>
Link: https://patch.msgid.link/20251126032249.69358-1-jiefeng.z.zhang@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a potential counter roll-over issue in fbnic_mbx_alloc_rx_msgs()
when calculating descriptor slots. The issue occurs when head - tail
results in a large positive value (unsigned) and the compiler interprets
head - tail - 1 as a signed value.
Since FBNIC_IPC_MBX_DESC_LEN is a power of two, use a masking operation,
which is a common way of avoiding this problem when dealing with these
sort of ring space calculations.
Fixes: da3cde0820 ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20251125211704.3222413-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There have been reports that RTL8127 hangs on suspend and shutdown,
partially disappearing from lspci until power-cycling.
According to Realtek disabling PLL's when switching to D3 should be
avoided on that chip version. Fix this by aligning disabling PLL's
with the vendor drivers, what in addition results in PLL's not being
disabled when switching to D3hot on other chip versions.
Fixes: f24f7b2f3a ("r8169: add support for RTL8127A")
Tested-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/d7faae7e-66bc-404a-a432-3a496600575f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when skb is null, the driver prints an error and then
dereferences skb on the next line.
To fix this, let's add a 'break' after the error message to switch
to sxgbe_rx_refill(), which is similar to the approach taken by the
other drivers in this particular case, e.g. calxeda with xgmac_rx().
Found during a code review.
Fixes: 1edb9ca69e ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121123834.97748-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rate limiting validation condition currently checks the output
variable max_bw_value[i] instead of the input value
maxrate->tc_maxrate[i]. This causes the validation to compare an
uninitialized or stale value rather than the actual requested rate.
The condition should check the input rate to properly validate against
the upper limit:
} else if (maxrate->tc_maxrate[i] <= upper_limit_gbps) {
This aligns with the pattern used in the first branch, which correctly
checks maxrate->tc_maxrate[i] against upper_limit_mbps.
The current implementation can lead to unreliable validation behavior:
- For rates between 25.5 Gbps and 255 Gbps, if max_bw_value[i] is 0
from initialization, the GBPS path may be taken regardless of whether
the actual rate is within bounds
- When processing multiple TCs (i > 0), max_bw_value[i] contains the
value computed for the previous TC, affecting the validation logic
- The overflow check for rates exceeding 255 Gbps may not trigger
consistently depending on previous array values
This patch ensures the validation correctly examines the requested rate
value for proper bounds checking.
Fixes: 43b27d1bd8 ("net/mlx5e: Fix wraparound in rate limiting for values above 255 Gbps")
Signed-off-by: Danielle Costantino <dcostantino@meta.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20251124180043.2314428-1-dcostantino@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To initialize the taprio block in lan966x, it is required to configure
the register REVISIT_DLY. The purpose of this register is to set the
delay before revisit the next gate and the value of this register depends
on the system clock. The problem is that the we calculated wrong the value
of the system clock period in picoseconds. The actual system clock is
~165.617754MHZ and this correspond to a period of 6038 pico seconds and
not 15125 as currently set.
Fixes: e462b27173 ("net: lan966x: Add offload support for taprio")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121061411.810571-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
be_insert_vlan_in_pkt() is called with the wrb_params argument being NULL
at be_send_pkt_to_bmc() call site. This may lead to dereferencing a NULL
pointer when processing a workaround for specific packet, as commit
bc0c3405ab ("be2net: fix a Tx stall bug caused by a specific ipv6
packet") states.
The correct way would be to pass the wrb_params from be_xmit().
Fixes: 760c295e0e ("be2net: Support for OS2BMC.")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://patch.msgid.link/20251119105015.194501-1-a.vatoropin@crpt.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-11-18 (idpf, ice)
This series contains updates to idpf and ice drivers.
Emil adds a check for NULL vport_config during removal to avoid NULL
pointer dereference in idpf.
Grzegorz fixes PTP teardown paths to account for some missed cleanups
for ice driver.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: fix PTP cleanup on driver removal in error path
idpf: fix possible vport_config NULL pointer deref in remove
====================
Link: https://patch.msgid.link/20251118235207.2165495-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Improve the cleanup on releasing PTP resources in error path.
The error case might happen either at the driver probe and PTP
feature initialization or on PTP restart (errors in reset handling, NVM
update etc). In both cases, calls to PF PTP cleanup (ice_ptp_cleanup_pf
function) and 'ps_lock' mutex deinitialization were missed.
Additionally, ptp clock was not unregistered in the latter case.
Keep PTP state as 'uninitialized' on init to distinguish between error
scenarios and to avoid resource release duplication at driver removal.
The consequence of missing ice_ptp_cleanup_pf call is the following call
trace dumped when ice_adapter object is freed (port list is not empty,
as it is required at this stage):
[ T93022] ------------[ cut here ]------------
[ T93022] WARNING: CPU: 10 PID: 93022 at
ice/ice_adapter.c:67 ice_adapter_put+0xef/0x100 [ice]
...
[ T93022] RIP: 0010:ice_adapter_put+0xef/0x100 [ice]
...
[ T93022] Call Trace:
[ T93022] <TASK>
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] ? __warn.cold+0xb0/0x10e
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] ? report_bug+0xd8/0x150
[ T93022] ? handle_bug+0xe9/0x110
[ T93022] ? exc_invalid_op+0x17/0x70
[ T93022] ? asm_exc_invalid_op+0x1a/0x20
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] pci_device_remove+0x42/0xb0
[ T93022] device_release_driver_internal+0x19f/0x200
[ T93022] driver_detach+0x48/0x90
[ T93022] bus_remove_driver+0x70/0xf0
[ T93022] pci_unregister_driver+0x42/0xb0
[ T93022] ice_module_exit+0x10/0xdb0 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
...
[ T93022] ---[ end trace 0000000000000000 ]---
[ T93022] ice: module unloaded
Fixes: e800654e85 ("ice: Use ice_adapter for PTP shared data instead of auxdev")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Handle skb allocation failures in RX path, to avoid NULL pointer
dereference and RX stalls under memory pressure. If the refill fails
with -ENOMEM, complete napi polling and wake up later to retry via timer.
Also explicitly re-enable RX DMA after oom, so the dmac doesn't remain
stopped in this situation.
Previously, memory pressure could lead to skb allocation failures and
subsequent Oops like:
Oops: Kernel access of bad area, sig: 11 [#2]
Hardware name: SonyPS3 Cell Broadband Engine 0x701000 PS3
NIP [c0003d0000065900] gelic_net_poll+0x6c/0x2d0 [ps3_gelic] (unreliable)
LR [c0003d00000659c4] gelic_net_poll+0x130/0x2d0 [ps3_gelic]
Call Trace:
gelic_net_poll+0x130/0x2d0 [ps3_gelic] (unreliable)
__napi_poll+0x44/0x168
net_rx_action+0x178/0x290
Steps to reproduce the issue:
1. Start a continuous network traffic, like scp of a 20GB file
2. Inject failslab errors using the kernel fault injection:
echo -1 > /sys/kernel/debug/failslab/times
echo 30 > /sys/kernel/debug/failslab/interval
echo 100 > /sys/kernel/debug/failslab/probability
3. After some time, traces start to appear, kernel Oopses
and the system stops
Step 2 is not always necessary, as it is usually already triggered by
the transfer of a big enough file.
Fixes: 02c1889166 ("ps3: gigabit ethernet driver for PS3, take3")
Signed-off-by: Florian Fuchs <fuchsfl@gmail.com>
Link: https://patch.msgid.link/20251113181000.3914980-1-fuchsfl@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The loops in 'qede_tpa_cont()' and 'qede_tpa_end()', iterate
over 'cqe->len_list[]' using only a zero-length terminator as
the stopping condition. If the terminator was missing or
malformed, the loop could run past the end of the fixed-size array.
Add an explicit bound check using ARRAY_SIZE() in both loops to prevent
a potential out-of-bounds access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 55482edc25 ("qede: Add slowpath/fastpath support and enable hardware GRO")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Link: https://patch.msgid.link/20251113112757.4166625-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Airoha_eth driver forwards offloaded uplink traffic (packets received
on GDM1 and forwarded to GDM{3,4}) to GDM2 in order to apply hw QoS.
This is correct if the device does not support a dedicated GDM2 port.
In this case, in order to enable hw offloading for uplink traffic,
the packets should be sent to GDM{3,4} directly.
Fixes: 9cd451d414 ("net: airoha: Add loopback support for GDM2")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251113-airoha-hw-offload-gdm2-fix-v1-1-7e4ca300872f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call to devlink_info_version_fixed_put() in
mlxsw_linecard_devlink_info_get() did not check for errors,
although it is checked everywhere in the code.
Add missed 'err' check to the mlxsw_linecard_devlink_info_get()
Fixes: 3fc0c51905 ("mlxsw: core_linecards: Expose device PSID over device info")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251113161922.813828-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function mlxsw_sp_flower_stats() calls mlxsw_sp_acl_ruleset_get() to
obtain a ruleset reference. If the subsequent call to
mlxsw_sp_acl_rule_lookup() fails to find a rule, the function returns
an error without releasing the ruleset reference, causing a memory leak.
Fix this by using a goto to the existing error handling label, which
calls mlxsw_sp_acl_ruleset_put() to properly release the reference.
Fixes: 7c1b8eb175 ("mlxsw: spectrum: Add support for TC flower offload statistics")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251112052114.1591695-1-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, CQs without a completion function are assigned the
mlx5_add_cq_to_tasklet function by default. This is problematic since
only user CQs created through the mlx5_ib driver are intended to use
this function.
Additionally, all CQs that will use doorbells instead of polling for
completions must call mlx5_cq_arm. However, the default CQ creation flow
leaves a valid value in the CQ's arm_db field, allowing FW to send
interrupts to polling-only CQs in certain corner cases.
These two factors would allow a polling-only kernel CQ to be triggered
by an EQ interrupt and call a completion function intended only for user
CQs, causing a null pointer exception.
Some areas in the driver have prevented this issue with one-off fixes
but did not address the root cause.
This patch fixes the described issue by adding defaults to the create CQ
flow. It adds a default dummy completion function to protect against
null pointer exceptions, and it sets an invalid command sequence number
by default in kernel CQs to prevent the FW from sending an interrupt to
the CQ until it is armed. User CQs are responsible for their own
initialization values.
Callers of mlx5_core_create_cq are responsible for changing the
completion function and arming the CQ per their needs.
Fixes: cdd04f4d4d ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Akiva Goldberger <agoldberger@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Link: https://patch.msgid.link/1762681743-1084694-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Change the debug message to print the correct units instead of always
assuming Gbps, as the value can be in either 100 Mbps or 1 Gbps units.
Fixes: 5da8bc3eff ("net/mlx5e: DCBNL, Add debug messages log")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1762681073-1084058-6-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The previous calculation used roundup() which caused an overflow for
rates between 25.5Gbps and 26Gbps.
For example, a rate of 25.6Gbps would result in using 100Mbps units with
value of 256, which would overflow the 8 bits field.
Simplify the upper_limit_mbps calculation by removing the
unnecessary roundup, and adjust the comparison to use <= to correctly
handle the boundary condition.
Fixes: d8880795da ("net/mlx5e: Implement DCBNL IEEE max rate")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1762681073-1084058-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When trying to set num_doorbells to a value greater than the max number
of channels, the error message was going over the netlink limit of 80
chars, truncating the most important part of the message, the number of
channels.
Fix that by trimming the length a bit.
Fixes: 11bbcfb766 ("net/mlx5e: Use the 'num_doorbells' devlink param")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1762681073-1084058-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The am65_cpsw_iet_verify_wait() function attempts verification 20 times,
toggling the AM65_CPSW_PN_IET_MAC_LINKFAIL bit in each iteration. When
the LINKFAIL bit transitions from 1 to 0, the MAC merge layer initiates
the verification process and waits for the timeout configured in
MAC_VERIFY_CNT before automatically retransmitting. The MAC_VERIFY_CNT
register is configured according to the user-defined verify/response
timeout in am65_cpsw_iet_set_verify_timeout_count(). As per IEEE 802.3
Clause 99, the hardware performs this automatic retry up to 3 times.
Current implementation toggles LINKFAIL after the user-configured
verify/response timeout in each iteration, forcing the hardware to
restart verification instead of respecting the MAC_VERIFY_CNT timeout.
This bypasses the hardware's automatic retry mechanism.
Fix this by moving the LINKFAIL bit toggle outside the retry loop and
reducing the retry count from 20 to 3. The software now only monitors
the status register while the hardware autonomously handles the 3
verification attempts at proper MAC_VERIFY_CNT intervals.
Fixes: 49a2eb9068 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20251106092305.1437347-3-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CPSW module uses the MAC_VERIFY_CNT bit field in the
CPSW_PN_IET_VERIFY_REG_k register to set the verify/response timeout
count. This register specifies the number of clock cycles to wait before
resending a verify packet if the verification fails.
The verify/response timeout count, as being set by the function
am65_cpsw_iet_set_verify_timeout_count() is hardcoded for 125MHz
clock frequency, which varies based on PHY mode and link speed.
The respective clock frequencies are as follows:
- RGMII mode:
* 1000 Mbps: 125 MHz
* 100 Mbps: 25 MHz
* 10 Mbps: 2.5 MHz
- QSGMII/SGMII mode: 125 MHz (all speeds)
Fix this by adding logic to calculate the correct timeout counts
based on the actual PHY interface mode and link speed.
Fixes: 49a2eb9068 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20251106092305.1437347-2-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Two additional bytes in front of each frame received into the RX FIFO if
SHIFT16 is set, so we need to subtract the extra two bytes from pkt_len
to correct the statistic of rx_bytes.
Fixes: 3ac72b7b63 ("net: fec: align IP header in hardware")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251106021421.2096585-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following warning was seen when we try to connect using ssh to the device.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:575
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 104, name: dropbear
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
CPU: 0 UID: 0 PID: 104 Comm: dropbear Tainted: G W 6.18.0-rc2-00399-g6f1ab1b109b9-dirty #530 NONE
Tainted: [W]=WARN
Hardware name: Generic DT based system
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x7c/0xac
dump_stack_lvl from __might_resched+0x16c/0x2b0
__might_resched from __mutex_lock+0x64/0xd34
__mutex_lock from mutex_lock_nested+0x1c/0x24
mutex_lock_nested from lan966x_stats_get+0x5c/0x558
lan966x_stats_get from dev_get_stats+0x40/0x43c
dev_get_stats from dev_seq_printf_stats+0x3c/0x184
dev_seq_printf_stats from dev_seq_show+0x10/0x30
dev_seq_show from seq_read_iter+0x350/0x4ec
seq_read_iter from seq_read+0xfc/0x194
seq_read from proc_reg_read+0xac/0x100
proc_reg_read from vfs_read+0xb0/0x2b0
vfs_read from ksys_read+0x6c/0xec
ksys_read from ret_fast_syscall+0x0/0x1c
Exception stack(0xf0b11fa8 to 0xf0b11ff0)
1fa0: 00000001 00001000 00000008 be9048d8 00001000 00000001
1fc0: 00000001 00001000 00000008 00000003 be905920 0000001e 00000000 00000001
1fe0: 0005404c be9048c0 00018684 b6ec2cd8
It seems that we are using a mutex in a atomic context which is wrong.
Change the mutex with a spinlock.
Fixes: 12c2d0a5b8 ("net: lan966x: add ethtool configuration and statistics")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251105074955.1766792-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device bus LAN ID was obtained from PCI_FUNC(), but when a PF
port is passthrough to a virtual machine, the function number may not
match the actual port index on the device. This could cause the driver
to perform operations such as LAN reset on the wrong port.
Fix this by reading the LAN ID from port status register.
Fixes: a34b3e6ed8 ("net: txgbe: Store PCI info")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/B60A670C1F52CB8E+20251104062321.40059-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MLX5E_SHAMPO_WQ_HEADER_PER_PAGE and
MLX5E_SHAMPO_LOG_MAX_HEADER_ENTRY_SIZE macros are used directly in
several places under the assumption that there will always be more
headers per WQE than headers per page. However, this assumption doesn't
hold for 64K page sizes and higher MTUs (> 4K). This can be first
observed during header page allocation: ksm_entries will become 0 during
alignment to MLX5E_SHAMPO_WQ_HEADER_PER_PAGE.
This patch introduces 2 additional members to the mlx5e_shampo_hd struct
which are meant to be used instead of the macrose mentioned above.
When the number of headers per WQE goes below
MLX5E_SHAMPO_WQ_HEADER_PER_PAGE, clamp the number of headers per
page and expand the header size accordingly so that the headers
for one WQE cover a full page.
All the formulas are adapted to use these two new members.
Fixes: 945ca432bf ("net/mlx5e: SHAMPO, Drop info array")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1762238915-1027590-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5e_hw_gro_skb_has_enough_space() uses a formula to check if there is
enough space in the skb frags to store more data. This formula is
incorrect for 64K page sizes and it triggers early GRO session
termination because the first fragment will blow up beyond
GRO_LEGACY_MAX_SIZE.
This patch adds a special case for page sizes >= GRO_LEGACY_MAX_SIZE
(64K) which uses the skb->len instead. Within this context,
the check is safe from fragment overflow because the hardware
will continuously fill the data up to the reservation size of 64K
and the driver will coalesce all data from the same page to the same
fragment. This means that the data will span one fragment or at most
two for such a large page size.
It is expected that the if statement will be optimized out as the
check is done with constants.
Fixes: 92552d3abd ("net/mlx5e: HW_GRO cqe handler implementation")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1762238915-1027590-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
HW-GRO is broken on mlx5 for 64K page sizes. The patch in the fixes tag
didn't take into account larger page sizes when doing an align down
of max_ksm_entries. For 64K page size, max_ksm_entries is 0 which will skip
mapping header pages via WQE UMR. This breaks header-data split
and will result in the following syndrome:
mlx5_core 0000:00:08.0 eth2: Error cqe on cqn 0x4c9, ci 0x0, qn 0x1133, opcode 0xe, syndrome 0x4, vendor syndrome 0x32
00000000: 00 00 00 00 04 4a 00 00 00 00 00 00 20 00 93 32
00000010: 55 00 00 00 fb cc 00 00 00 00 00 00 07 18 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4a
00000030: 00 00 3b c7 93 01 32 04 00 00 00 00 00 00 bf e0
mlx5_core 0000:00:08.0 eth2: ERR CQE on RQ: 0x1133
Furthermore, the function that fills in WQE UMRs for the headers
(mlx5e_build_shampo_hd_umr()) only supports mapping page sizes that
fit in a single UMR WQE.
This patch goes back to the old non-aligned max_ksm_entries value and it
changes mlx5e_build_shampo_hd_umr() to support mapping a large page over
multiple UMR WQEs.
This means that mlx5e_build_shampo_hd_umr() can now leave a page only
partially mapped. The caller, mlx5e_alloc_rx_hd_mpwqe(), ensures that
there are enough UMR WQEs to cover complete pages by working on
ksm_entries that are multiples of MLX5E_SHAMPO_WQ_HEADER_PER_PAGE.
Fixes: 8a0ee54027 ("net/mlx5e: SHAMPO, Simplify UMR allocation for headers")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1762238915-1027590-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ICSSG driver does the initial FDB configuration which
includes setting the control registers. Other run time
management like learning is managed by the PRU's. The default
FDB hash size used by the firmware is 512 slots, which is
currently missing in the current driver. Update the driver
FDB config to include FDB hash size as well.
Please refer trm [1] 6.4.14.12.17 section on how the FDB config
register gets configured. From the table 6-1404, there is a reset
field for FDB_HAS_SIZE which is 4, meaning 1024 slots. Currently
the driver is not updating this reset value from 4(1024 slots) to
3(512 slots). This patch fixes this by updating the reset value
to 512 slots.
[1]: https://www.ti.com/lit/pdf/spruim2
Fixes: abd5576b9c ("net: ti: icssg-prueth: Add support for ICSSG switch firmware")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251104104415.3110537-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LIBIE_FWLOG is unusable without DEBUG_FS. Mark it in Kconfig.
Fix build error on ixgbe when DEBUG_FS is not set. To not add another
layer of #if IS_ENABLED(LIBIE_FWLOG) in ixgbe fwlog code define debugfs
dentry even when DEBUG_FS isn't enabled. In this case the dummy
functions of LIBIE_FWLOG will be used, so not initialized dentry isn't a
problem.
Fixes: 641585bc97 ("ixgbe: fwlog support for e610")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/lkml/f594c621-f9e1-49f2-af31-23fbcb176058@roeck-us.net/
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20251104172333.752445-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make knav_dma_open_channel consistently return NULL on error instead
of ERR_PTR. Currently the header include/linux/soc/ti/knav_dma.h
returns NULL when the driver is disabled, but the driver
implementation does not even return NULL or ERR_PTR on failure,
causing inconsistency in the users. This results in a crash in
netcp_free_navigator_resources as followed (trimmed):
Unhandled fault: alignment exception (0x221) at 0xfffffff2
[fffffff2] *pgd=80000800207003, *pmd=82ffda003, *pte=00000000
Internal error: : 221 [#1] SMP ARM
Modules linked in:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.17.0-rc7 #1 NONE
Hardware name: Keystone
PC is at knav_dma_close_channel+0x30/0x19c
LR is at netcp_free_navigator_resources+0x2c/0x28c
[... TRIM...]
Call trace:
knav_dma_close_channel from netcp_free_navigator_resources+0x2c/0x28c
netcp_free_navigator_resources from netcp_ndo_open+0x430/0x46c
netcp_ndo_open from __dev_open+0x114/0x29c
__dev_open from __dev_change_flags+0x190/0x208
__dev_change_flags from netif_change_flags+0x1c/0x58
netif_change_flags from dev_change_flags+0x38/0xa0
dev_change_flags from ip_auto_config+0x2c4/0x11f0
ip_auto_config from do_one_initcall+0x58/0x200
do_one_initcall from kernel_init_freeable+0x1cc/0x238
kernel_init_freeable from kernel_init+0x1c/0x12c
kernel_init from ret_from_fork+0x14/0x38
[... TRIM...]
Standardize the error handling by making the function return NULL on
all error conditions. The API is used in just the netcp_core.c so the
impact is limited.
Note, this change, in effect reverts commit 5b6cb43b4d ("net:
ethernet: ti: netcp_core: return error while dma channel open issue"),
but provides a less error prone implementation.
Suggested-by: Simon Horman <horms@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251103162811.3730055-1-nm@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existing code calls bnxt_cancel_reservations() after
bnxt_hwrm_func_drv_unrgtr() in bnxt_dl_reload_down().
bnxt_cancel_reservations() calls the FW and it will always fail since
the driver has already unregistered, triggering this warning:
bnxt_en 0000:0a:00.0 ens2np0: resc_qcaps failed
Fix it by calling bnxt_clear_reservations() which will skip the
unnecessary FW call since we have unregistered.
Fixes: 228ea8c187 ("bnxt_en: implement devlink dev reload driver_reinit")
Reviewed-by: Mohammad Shuab Siddique <mohammad-shuab.siddique@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shantiprasad Shettar <shantiprasad.shettar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While populating firmware host logging segments for the coredump, it is
possible for the FW command that flushes the segment to fail. When that
happens, the existing code will not update the max entry and entry size
in the segment header and this causes software that decodes the coredump
to skip the segment.
The segment most likely has already collected some DMA data, so always
update these 2 segment fields in the header to allow the decoder to
decode any data in the segment.
Fixes: 3c2179e663 ("bnxt_en: Add FW trace coredump segments to the coredump")
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-5-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With older FW, we may get the ASYNC_EVENT_CMPL_EVENT_ID_DBG_BUF_PRODUCER
for FW trace data type that has not been initialized. This will result
in a crash in bnxt_bs_trace_type_wrap(). Add a guard to check for a
valid magic_byte pointer before proceeding.
Fixes: 84fcd9449f ("bnxt_en: Manage the FW trace context memory")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Gautam R A <gautam-r.a@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In bnxt_ptp_init(), when ptp_clock_register() fails, the driver is
not freeing the memory allocated for ptp_info->pin_config. Fix it
to unconditionally free ptp_info->pin_config in bnxt_ptp_free().
Fixes: caf3eedbcd ("bnxt_en: 1PPS support for 5750X family chips")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The netif_close() call in bnxt_shutdown() only stops packet DMA. There
may be FW DMA for trace logging (recently added) that will continue. If
we kexec to a new kernel, the DMA will corrupt memory in the new kernel.
Add bnxt_hwrm_func_drv_unrgtr() to unregister the driver from the FW.
This will stop the FW DMA. In case the call fails, call pcie_flr() to
reset the function and stop the DMA.
Fixes: 24d694aec1 ("bnxt_en: Allocate backing store memory for FW trace logs")
Reported-by: Jakub Kicinski <kicinski@meta.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, emac_set_pauseparam() will oops if userspace calls it while
the interface is not up, because phydev is NULL, but it is still
accessed in emac_set_fc() and emac_set_fc_autoneg().
Check for netif_running(dev) in emac_set_pauseparam() before proceeding.
Fixes: bfec6d7f20 ("net: spacemit: Add K1 Ethernet MAC")
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251103-k1-ethernet-remove-fc-v3-1-2083770cd282@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devm_kcalloc() function never return error pointers, it returns NULL
on failure. Also delete the netdev_err() printk. These allocation
functions already have debug output built-in some the extra error message
is not required.
Fixes: efabce2901 ("octeontx2-pf: AF_XDP zero copy receive support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aQYKkrGA12REb2sj@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TSO path called ionic_tx_map_skb() before preparing the TCP pseudo
checksum (ionic_tx_tcp_[inner_]pseudo_csum()), which may perform
skb_cow_head() and might modifies bytes in the linear header area.
Mapping first and then mutating the header risks:
- Using a stale DMA address if skb_cow_head() relocates the head, and/or
- Device reading stale header bytes on weakly-ordered systems
(CPU writes after mapping are not guaranteed visible without an
explicit dma_sync_single_for_device()).
Reorder the TX path to perform all header mutations (including
skb_cow_head()) *before* DMA mapping. Mapping is now done only after the
skb layout and header contents are final. This removes the need for any
post-mapping dma_sync and prevents on-wire corruption observed under
VLAN+TSO load after repeated runs.
This change is purely an ordering fix; no functional behavior change
otherwise.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20251031155203.203031-2-mheib@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TX path currently writes descriptors and then immediately writes to
the MMIO doorbell register to notify the NIC. On weakly ordered
architectures, descriptor writes may still be pending in CPU or DMA
write buffers when the doorbell is issued, leading to the device
fetching stale or incomplete descriptors.
Add a dma_wmb() in ionic_txq_post() to ensure all descriptor writes are
visible to the device before the doorbell MMIO write.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Link: https://patch.msgid.link/20251031155203.203031-1-mheib@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gve implemented a ptp_clock for sole use of do_aux_work at this time.
ptp_clock_gettime() and ptp_sys_offset() assume every ptp_clock has
implemented either gettimex64 or gettime64. Stub gettimex64 and return
-EOPNOTSUPP to prevent NULL dereferencing.
Fixes: acd1638052 ("gve: Add initial PTP device support")
Reported-by: syzbot+c8c0e7ccabd456541612@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c8c0e7ccabd456541612
Signed-off-by: Tim Hostetler <thostet@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20251029184555.3852952-2-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
