GPIO controller driver should typically implement the .get_direction()
callback as GPIOLIB internals may try to use it to determine the state
of a pin. Add it for the LPASS LPI driver.
Reported-by: Abel Vesa <abelvesa@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 6e261d1090 ("pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # X1E CRD
Tested-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Qualcomm SC7280 and SM8350 SoCs have slightly different LPASS audio
blocks (v9.4.5 and v9.2), however the LPASS LPI pin controllers are
exactly the same. The driver for SM8350 has two issues, which can be
fixed by simply moving over to SC7280 driver which has them correct:
1. "i2s2_data_groups" listed twice GPIO12, but should have both GPIO12
and GPIO13,
2. "swr_tx_data_groups" contained GPIO5 for "swr_tx_data2" function, but
that function is also available on GPIO14, thus listing it twice is
not necessary. OTOH, GPIO5 has also "swr_rx_data1", so selecting
swr_rx_data function should not block the TX one.
Fixes: be9f6d5638 ("pinctrl: qcom: sm8350-lpass-lpi: add SM8350 LPASS TLMM")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Core changes:
- Handle per-direction skew control in the generic pin config.
- Drop the pointless subsystem boilerplate banner message during
boot. Less noise in the console. It's available as debug message
if someone really want it.
New drivers:
- Samsung Exynos 8890 SoC support.
- Samsung Exynos derived Axis Communications ARTPEC-9 SoC support.
These guys literally live next door to me, ARTPEC spells out
"Axis Real-Time Picture Encoding Chip" and is tailored for camera
image streams and is something they have evolved for a quarter of
a century.
- Mediatek MT6878 SoC support.
- Qualcomm Glymur PMIC support (mostly just compatible strings).
- Qualcomm Kaanapali SoC TLMM support.
- Microchip pic64gx "gpio2" SoC support.
- Microchip Polarfire "iomux0" SoC support.
- CIX Semiconductors SKY1 SoC support.
- Rockchip RK3506 SoC support.
- Airhoa AN7583 chip support.
Improvements:
- Improvements for ST Microelectronics STM32 handling of skew
settings so input and output can have different skew settings.
- A whole bunch of device tree binding cleanups: Marvell Armada and
Berlin, Actions Semiconductor S700 and S900, Broadcom Northstar 2
(NS2), Bitmain BM1880 and Spreadtrum SC9860 are moved over to schema.
-----BEGIN PGP SIGNATURE-----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=/AU5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"The technical details below. For me the CIX Semi and Axis
Communications ARTPEC-9 SoCs were the most interesting new drivers in
this merge window.
Core changes:
- Handle per-direction skew control in the generic pin config
- Drop the pointless subsystem boilerplate banner message during
boot. Less noise in the console. It's available as debug message if
someone really want it
New drivers:
- Samsung Exynos 8890 SoC support
- Samsung Exynos derived Axis Communications ARTPEC-9 SoC support.
These guys literally live next door to me, ARTPEC spells out "Axis
Real-Time Picture Encoding Chip" and is tailored for camera image
streams and is something they have evolved for a quarter of a
century
- Mediatek MT6878 SoC support
- Qualcomm Glymur PMIC support (mostly just compatible strings)
- Qualcomm Kaanapali SoC TLMM support
- Microchip pic64gx "gpio2" SoC support
- Microchip Polarfire "iomux0" SoC support
- CIX Semiconductors SKY1 SoC support
- Rockchip RK3506 SoC support
- Airhoa AN7583 chip support
Improvements:
- Improvements for ST Microelectronics STM32 handling of skew
settings so input and output can have different skew settings
- A whole bunch of device tree binding cleanups: Marvell Armada and
Berlin, Actions Semiconductor S700 and S900, Broadcom Northstar 2
(NS2), Bitmain BM1880 and Spreadtrum SC9860 are moved over to
schema"
* tag 'pinctrl-v6.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
pinctrl: add CONFIG_OF dependencies for microchip drivers
pinctrl: starfive: use dynamic GPIO base allocation
pinctrl: single: Fix incorrect type for error return variable
MAINTAINERS: Change Linus Walleij mail address
pinctrl: cix: Fix obscure dependency
dt-bindings: pinctrl: cix,sky1-pinctrl: Drop duplicate newline
dt-bindings: pinctrl: aspeed,ast2600-pinctrl: Add PCIe RC PERST# group
pinctrl: airoha: Fix AIROHA_PINCTRL_CONFS_DRIVE_E2 in an7583_pinctrl_match_data
pinctrl: airoha: fix pinctrl function mismatch issue
pinctrl: cherryview: Convert to use intel_gpio_add_pin_ranges()
pinctrl: intel: Export intel_gpio_add_pin_ranges()
pinctrl: renesas: rzg2l: Refactor OEN register PWPR handling
pinctrl: airoha: convert comma to semicolon
pinctrl: elkhartlake: Switch to INTEL_GPP() macro
pinctrl: cherryview: Switch to INTEL_GPP() macro
pinctrl: emmitsburg: Switch to INTEL_GPP() macro
pinctrl: denverton: Switch to INTEL_GPP() macro
pinctrl: cedarfork: Switch to INTEL_GPP() macro
pinctrl: airoha: add support for Airoha AN7583 PINs
dt-bindings: pinctrl: airoha: Document AN7583 Pin Controller
...
Replace disable_irq() with disable_irq_nosync() in msm_pinmux_set_mux()
to prevent deadlock when wakeup IRQ is triggered on the same
GPIO being reconfigured.
The issue occurs when a wakeup IRQ is triggered on a GPIO and the IRQ
handler attempts to reconfigure the same GPIO's pinmux. In this scenario,
msm_pinmux_set_mux() calls disable_irq() which waits for the currently
running IRQ handler to complete, creating a circular dependency that
results in deadlock.
Using disable_irq_nosync() avoids waiting for the IRQ handler to
complete, preventing the deadlock condition while still properly
disabling the interrupt during pinmux reconfiguration.
Suggested-by: Prasad Sodagudi <prasad.sodagudi@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for Kaanapali TLMM configuration and control via the pinctrl
framework.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mark the gpio/egpio as GPIO specific pin functions, othewise
the pin muxing generic framework will complain about the gpio
being already requested by a different owner.
Fixes: 87ebcd8bae ("pinctrl: qcom: Add glymur pinctrl driver")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The platform specific configuration is already passed on to the generic
msm probe. So it's useless to exist in the match table next to the
compatible. So drop it from match table.
Fixes: 87ebcd8bae ("pinctrl: qcom: Add glymur pinctrl driver")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Snapdragon 660 has a Low-Power Island (LPI) TLMM for configuring
pins related to audio. Add the driver for this.
Also, this driver uses predefined pin_offsets for each pin taken from
downstream driver, which does not follow the usual 0x1000 distance
between pins and uses an array with predefined offsets that do not
follow any regular pattern [1].
[1] https://git.codelinaro.org/clo/la/kernel/msm-4.4/-/blob/LA.UM.7.2.c27-07400-sdm660.0/drivers/pinctrl/qcom/pinctrl-lpi.c#L107
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Co-developed-by: Nickolay Goppen <setotau@mainlining.org>
Signed-off-by: Nickolay Goppen <setotau@mainlining.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By default pin_offset is calculated by formula: LPI_TLMM_REG_OFFSET * pin_id.
However not all platforms are using this pin_offset formula (e.g. SDM660 LPASS
LPI uses a predefined array of offsets [1]), so extend lpi_pingroup struct
with pin_offset field, introduce extended LPI_PINGROUP_OFFSET macro with
pin_offet field and introduce LPI_FLAG_USE_PREDEFINED_PIN_OFFSET flag.
This adds an ability to use predefined offset for pin if it exists.
[1] https://git.codelinaro.org/clo/la/kernel/msm-4.4/-/blob/LA.UM.7.2.c27-07400-sdm660.0/drivers/pinctrl/qcom/pinctrl-lpi.c#L107
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Nickolay Goppen <setotau@mainlining.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This mirrors the egpio support added to sc7280/sm8450/etc. This change
is necessary for GPIOs 146 - 179 (34 GPIOs) to be used as normal GPIOs.
Signed-off-by: Sean Parker <sean.parker@viasat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This generic pin config property is confusingly named so let's
rename it to make things clearer.
There are already drivers in the tree that use PIN_CONFIG_OUTPUT
to *read* the value of an output driven pin, which is a big
semantic confusion for the head: are we then reading the
setting of the output or the actual value/level that is put
out on the pin?
We already have PIN_CONFIG_OUTPUT_ENABLE that turns on driver
buffers for output, so this can by logical conclusion only
drive the voltage level if it should be any different.
But if we read the pin, are we then reading the *setting* of
the output value or the *actual* value we can see on the
line?
If the pin has not first been set into output mode with
PIN_CONFIG_OUTPUT_ENABLE, but is instead in some input mode
or tristate, what will reading this property actually
return?
Reading the current users reading this property it is clear
that what we read is the logical level of the pin as 0 or 1
depending on if it is low or high.
Rename it to PIN_CONFIG_LEVEL so it is crystal clear that
we set or read the voltage level of the pin and nothing else.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The strict flag in struct pinmux_ops disallows the usage of the same pin
as a GPIO and for another function. Without it, a rouge user-space
process with enough privileges (or even a buggy driver) can request a
used pin as GPIO and drive it, potentially confusing devices or even
crashing the system. Set it globally for all pinctrl-msm users.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow pins muxed to the "gpio" or "egpio" function to be requested as
GPIOs even if pinmux_ops say the controller should be strict.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a helper macro that wraps PINCTRL_GPIO_PINFUNCTION() for pinctrl-msm
pin functions and assign the .function_is_gpio() callback in pinmux_ops.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the pinmux core no longer duplicating memory used to store the
struct pinfunction objects in .rodata, we can now use the existing
infrastructure for storing and looking up pin functions in qualcomm
drivers. Remove hand-crafted callbacks.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_kcalloc() in sc8180x_pinctrl_add_tile_resources() to gain built-in
overflow protection, making memory allocation safer when calculating
allocation size compared to explicit multiplication.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250819143935.372084-4-rongqianfeng@vivo.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Core changes:
- Open code PINCTRL_FUNCTION_DESC() instead of defining
a complex macro only used in one place.
- Add pinmux_generic_add_pinfunction() helper and
use this in a few drivers.
New drivers:
- Amlogic S7, S7D and S6 pin control support.
- Eswin EIC7700 pin control support.
- Qualcomm PMIV0104, PM7550 and Milos pin control
support.
Because of unhelpful numbering schemes, the Qualcomm
driver now needs to start to rely on SoC codenames.
- STM32 HDP pin control support.
- Mediatek MT8189 pin control support.
Improvements:
- Switch remaining pin control drivers over to the
new GPIO set callback that provides a return value.
- Support RSVD (reserved) pins in the STM32 driver.
- Move many fixed assignments over to pinctrl_desc
definitions.
- Handle multiple TLMM regions in the Qualcomm driver.
-----BEGIN PGP SIGNATURE-----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=hEj7
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Nothing stands out, apart from maybe the interesting Eswin EIC7700, a
RISC-V SoC I've never seen before.
Core changes:
- Open code PINCTRL_FUNCTION_DESC() instead of defining a complex
macro only used in one place
- Add pinmux_generic_add_pinfunction() helper and use this in a few
drivers
New drivers:
- Amlogic S7, S7D and S6 pin control support
- Eswin EIC7700 pin control support
- Qualcomm PMIV0104, PM7550 and Milos pin control support
Because of unhelpful numbering schemes, the Qualcomm driver now
needs to start to rely on SoC codenames
- STM32 HDP pin control support
- Mediatek MT8189 pin control support
Improvements:
- Switch remaining pin control drivers over to the new GPIO set
callback that provides a return value
- Support RSVD (reserved) pins in the STM32 driver
- Move many fixed assignments over to pinctrl_desc definitions
- Handle multiple TLMM regions in the Qualcomm driver"
* tag 'pinctrl-v6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (105 commits)
pinctrl: mediatek: Add pinctrl driver for mt8189
dt-bindings: pinctrl: mediatek: Add support for mt8189
pinctrl: aspeed-g6: Add PCIe RC PERST pin group
pinctrl: ingenic: use pinmux_generic_add_pinfunction()
pinctrl: keembay: use pinmux_generic_add_pinfunction()
pinctrl: mediatek: moore: use pinmux_generic_add_pinfunction()
pinctrl: airoha: use pinmux_generic_add_pinfunction()
pinctrl: equilibrium: use pinmux_generic_add_pinfunction()
pinctrl: provide pinmux_generic_add_pinfunction()
pinctrl: pinmux: open-code PINCTRL_FUNCTION_DESC()
pinctrl: ma35: use new GPIO line value setter callbacks
MAINTAINERS: add Clément Le Goffic as STM32 HDP maintainer
pinctrl: stm32: Introduce HDP driver
dt-bindings: pinctrl: stm32: Introduce HDP
pinctrl: qcom: Add Milos pinctrl driver
dt-bindings: pinctrl: document the Milos Top Level Mode Multiplexer
pinctrl: qcom: spmi: Add PM7550
dt-bindings: pinctrl: qcom,pmic-gpio: Add PM7550 support
pinctrl: qcom: spmi: Add PMIV0104
dt-bindings: pinctrl: qcom,pmic-gpio: Add PMIV0104 support
...
Add support for selecting multiple TLMM regions using the
tlmm-test tool.
The current implementation only selects the TLMM Node region
0, which can lead to incorrect region selection.
QCS 615 TLMM Node dts reg:
tlmm: pinctrl@3100000 {
compatible = "qcom,qcs615-tlmm";
reg = <0x0 0x03100000 0x0 0x300000>,
<0x0 0x03500000 0x0 0x300000>,
<0x0 0x03d00000 0x0 0x300000>;
reg-names = "east",
"west",
"south";
QCS615 gpio57 is in the south region with an offset of 0x39000,
and its address is 0x3d39000. However, the default region selection
is region 0 (east region), resulting in a wrong calculated address
of 0x3139000.
Add a tlmm option parameter named tlmm_reg_name to select the region.
If the user does not input the parameter, the default region is 0.
Signed-off-by: Yuanjie Yang <quic_yuanjiey@quicinc.com>
Link: https://lore.kernel.org/20250624090600.91063-1-quic_yuanjiey@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some platforms, the UFS-reset pin has no interrupt logic in TLMM but
is nevertheless registered as a GPIO in the kernel. This enables the
user-space to trigger a BUG() in the pinctrl-msm driver by running, for
example: `gpiomon -c 0 113` on RB2.
The exact culprit is requesting pins whose intr_detection_width setting
is not 1 or 2 for interrupts. This hits a BUG() in
msm_gpio_irq_set_type(). Potentially crashing the kernel due to an
invalid request from user-space is not optimal, so let's go through the
pins and mark those that would fail the check as invalid for the irq chip
as we should not even register them as available irqs.
This function can be extended if we determine that there are more
corner-cases like this.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Cc: stable@vger.kernel.org
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/20250612091448.41546-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to simplify cleanup actions, use devres-enabled version of
gpiochip_add_data(). As the msm_pinctrl_remove() function is now empty,
drop it and all its calls from the corresponding pinctrl drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250513-pinctrl-msm-fix-v2-3-249999af0fc1@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add the devres devm_pinctrl_register_mappings() call that can
register some pin control machine mappings and have them go away
with the associated device.
New drivers:
- Support for the Mediatek MT6893 and MT8196 SoCs.
- Support for the Renesas RZ/V2N SoC.
- Support for the NXP Freescale i.MX943 SoC.
Improvements:
- Per-SoC suspend/resume callbacks in the Samsung drivers.
- Set all pins as input (High-Z) at probe in the MCP23S08 driver.
- Switch most GPIO chips to use the setters/getters with a return
value.
- EGPIO support in the Qualcomm QCM2290 driver.
- Fix up the number of available GPIO lines in Qualcomm QCS8300
and QCS615.
-----BEGIN PGP SIGNATURE-----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=Qr9t
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"An especially linear and sparse improvement and new drivers release.
Nothing exciting. The biggest change in Bartosz changes to make
gpiochip set/get calls return error codes (something we should have
fixed ages ago but is now finally getting fixed.)
Core changes:
- Add the devres devm_pinctrl_register_mappings() call that can
register some pin control machine mappings and have them go away
with the associated device
New drivers:
- Support for the Mediatek MT6893 and MT8196 SoCs
- Support for the Renesas RZ/V2N SoC
- Support for the NXP Freescale i.MX943 SoC
Improvements:
- Per-SoC suspend/resume callbacks in the Samsung drivers
- Set all pins as input (High-Z) at probe in the MCP23S08 driver
- Switch most GPIO chips to use the setters/getters with a return
value
- EGPIO support in the Qualcomm QCM2290 driver
- Fix up the number of available GPIO lines in Qualcomm QCS8300 and
QCS615"
* tag 'pinctrl-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: freescale: Add support for imx943 pinctrl
pinctrl: core: add devm_pinctrl_register_mappings()
pinctrl: remove extern specifier for functions in machine.h
pinctrl: mediatek: eint: Fix invalid pointer dereference for v1 platforms
pinctrl: freescale: Enable driver if platform is enabled.
pinctrl: freescale: Depend imx-scu driver on OF
pinctrl: armada-37xx: propagate error from armada_37xx_pmx_set_by_name()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_get_direction()
pinctrl: armada-37xx: propagate error from armada_37xx_pmx_gpio_set_direction()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_get()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_direction_output()
pinctrl: armada-37xx: set GPIO output value before setting direction
pinctrl: armada-37xx: use correct OUTPUT_VAL register for GPIOs > 31
pinctrl: meson: Drop unused aml_pctl_find_group_by_name()
pinctrl: at91: Fix possible out-of-boundary access
pinctrl: add stubs for OF-specific pinconf functions
pinctrl: qcom: correct the ngpios entry for QCS8300
pinctrl: qcom: correct the ngpios entry for QCS615
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples for qcs8300
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples for qcs615
...
Error-handling paths in msm_pinctrl_probe() don't call
a function required to unroll restart handler registration,
unregister_restart_handler(). Instead of adding calls to this function,
switch the msm pinctrl code into using devm_register_sys_off_handler().
Fixes: cf1fc18762 ("pinctrl: qcom: use restart_notifier mechanism for ps_hold")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250513-pinctrl-msm-fix-v2-2-249999af0fc1@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct the ngpios entry to account for the UFS_RESET pin, which is
expected to be wired to the reset pin of the primary UFS memory and is
exported as GPIOs in addition to the real GPIOs, allowing the UFS driver
to toggle it.
Fixes: 0c4cd2cc87 ("pinctrl: qcom: add the tlmm driver for QCS8300 platforms")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Lijuan Gao <quic_lijuang@quicinc.com>
Link: https://lore.kernel.org/20250506-correct_gpio_ranges-v3-4-49a7d292befa@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct the ngpios entry to account for the UFS_RESET pin being exported
as a GPIO in addition to the real GPIOs, allowing the UFS driver to toggle
it.
Fixes: b698f36a9d ("pinctrl: qcom: add the tlmm driver for QCS615 platform")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Lijuan Gao <quic_lijuang@quicinc.com>
Link: https://lore.kernel.org/20250506-correct_gpio_ranges-v3-3-49a7d292befa@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On newer SoCs intr_target_bit position is at 8 instead of 5. Fix it.
Also add missing intr_wakeup_present_bit and intr_wakeup_enable_bit which
enables forwarding of GPIO interrupts to parent PDC interrupt controller.
Fixes: afe9803e3b ("pinctrl: qcom: Add sm8750 pinctrl driver")
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Link: https://lore.kernel.org/20250429-pinctrl_sm8750-v2-1-87d45dd3bd82@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250410-gpiochip-set-rv-pinctrl-qcom-v1-6-6a6891338aae@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250410-gpiochip-set-rv-pinctrl-qcom-v1-5-6a6891338aae@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250410-gpiochip-set-rv-pinctrl-qcom-v1-4-6a6891338aae@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250410-gpiochip-set-rv-pinctrl-qcom-v1-3-6a6891338aae@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250410-gpiochip-set-rv-pinctrl-qcom-v1-2-6a6891338aae@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250410-gpiochip-set-rv-pinctrl-qcom-v1-1-6a6891338aae@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
qcm2290 supports the egpio feature on GPIOs ranging from 98 to 126.
This change is necessary to allow these GPIOs to be driven by TLMM.
Signed-off-by: Wojciech Slenska <wojciech.slenska@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250409080030.62254-1-wojciech.slenska@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kunit_kzalloc() may return a NULL pointer, dereferencing it without
NULL check may lead to NULL dereference.
Add a NULL check for grp.
Fixes: c7984dc0a2 ("pinctrl: qcom: Add test case for TLMM interrupt handling")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/20250325094932.4733-1-hanchunchao@inspur.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Egpio feature allows IsLand Domain IOs to be reused as TLMM GPIOs.
sa8775p supports egpio feature for GPIOs ranging from 126 to 148.
Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
Reviewed-by: Dmitry Baryshkov <lumag@kernel.org>
Link: https://lore.kernel.org/20250312072509.3247885-3-quic_wasimn@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In commit 'cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts
when enabling")' Doug establishes an expectation that edge interrupts
occurring while an interrupt is disabled should be delivered once the
interrupt is enabled again.
Implement a test to validate that this is the case.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/20250313-tlmm-test-disabled-irq-delivered-v1-1-f0be903732ac@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
Cc: stable@vger.kernel.org
Fixes: cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts when enabling")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20250312-pinctrl-msm-type-latch-v1-1-ce87c561d3d7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While looking at the X1E PDC GPIO interrupts it became clear that we're
lacking a convenient and accessible way to validate if the TLMM
interrupt code performing as expected.
This introduces a kunit-based "hack" that relies on pin bias/pull
configuration to tickle the interrupt logic in non-connected pins to
allow us to evaluate that an expected number of interrupts are
delivered.
The bias/pull configuration is done with mmio accesses directly from the
test code, to avoid having to programmatically acquire and drive the
pinconf interface for the test pin. This limits the scalability of the
code to targets with a particular register layout, but serves our needs
for now.
The pin to be used for testing is specified by the tester using the
"tlmm-test.gpio" module parameter.
Worth mentioning is that some of the test cases currently fails for
GPIOs that is not backed by PDC (i.e. "non-wakeup" GPIOs), as lingering
latched interrupt state is being delivered at IRQ request time.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It looks like both 8917 and 8937 are the same except for one pin
"wsa_reset".
Signed-off-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/20250211-msm8937-v1-4-7d27ed67f708@mainlining.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Antonio Borneo <antonio.borneo@foss.st.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/20250114203602.1013275-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO configuration differs for the spi0 clk, cs, miso, mosi pins.
Therefore, split the spi0 pin group and assign function to each pin
as per the specification.
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/20241217091308.3253897-3-quic_mmanikan@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is based on MSM8916 driver with the pinctrl definitions from
Qualcomm's downstream MSM8917 driver.
Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/20241215-msm8917-v9-3-bacaa26f3eef@mainlining.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
