commit 6db541ae27 upstream.
If a login request fails, the recovery process should be protected
against parallel resets. It is a known issue that freeing and
registering CRQ's in quick succession can result in a failover CRQ from
the VIOS. Processing a failover during login recovery is dangerous for
two reasons:
1. This will result in two parallel initialization processes, this can
cause serious issues during login.
2. It is possible that the failover CRQ is received but never executed.
We get notified of a pending failover through a transport event CRQ.
The reset is not performed until a INIT CRQ request is received.
Previously, if CRQ init fails during login recovery, then the ibmvnic
irq is freed and the login process returned error. If failover_pending
is true (a transport event was received), then the ibmvnic device
would never be able to process the reset since it cannot receive the
CRQ_INIT request due to the irq being freed. This leaved the device
in a inoperable state.
Therefore, the login failure recovery process must be hardened against
these possible issues. Possible failovers (due to quick CRQ free and
init) must be avoided and any issues during re-initialization should be
dealt with instead of being propagated up the stack. This logic is
similar to that of ibmvnic_probe().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-5-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23cc5f6674 upstream.
Perform a partial reset before sending a login request if any of the
following are true:
1. If a previous request times out. This can be dangerous because the
VIOS could still receive the old login request at any point after
the timeout. Therefore, it is best to re-register the CRQ's and
sub-CRQ's before retrying.
2. If the previous request returns an error that is not described in
PAPR. PAPR provides procedures if the login returns with partial
success or aborted return codes (section L.5.1) but other values
do not have a defined procedure. Previously, these conditions
just returned error from the login function rather than trying
to resolve the issue.
This can cause further issues since most callers of the login
function are not prepared to handle an error when logging in. This
improper cleanup can lead to the device being permanently DOWN'd.
For example, if the VIOS believes that the device is already logged
in then it will return INVALID_STATE (-7). If we never re-register
CRQ's then it will always think that the device is already logged
in. This leaves the device inoperable.
The partial reset involves freeing the sub-CRQs, freeing the CRQ then
registering and initializing a new CRQ and sub-CRQs. This essentially
restarts all communication with VIOS to allow for a fresh login attempt
that will be unhindered by any previous failed attempts.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-4-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d78a671eb8 upstream.
Rather than leaving the DMA unmapping of the login buffers to the
login response handler, move this work into the login release functions.
Previously, these functions were only used for freeing the allocated
buffers. This could lead to issues if there are more than one
outstanding login buffer requests, which is possible if a login request
times out.
If a login request times out, then there is another call to send login.
The send login function makes a call to the login buffer release
function. In the past, this freed the buffers but did not DMA unmap.
Therefore, the VIOS could still write to the old login (now freed)
buffer. It is for this reason that it is a good idea to leave the DMA
unmap call to the login buffers release function.
Since the login buffer release functions now handle DMA unmapping,
remove the duplicate DMA unmapping in handle_login_rsp().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-3-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 411c565b4b upstream.
If the LOGIN CRQ fails to send then we must DMA unmap the response
buffer. Previously, if the CRQ failed then the memory was freed without
DMA unmapping.
Fixes: c98d9cc417 ("ibmvnic: send_login should check for crq errors")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db17ba719b upstream.
Ensure that all offsets in a login response buffer are within the size
of the allocated response buffer. Any offsets or lengths that surpass
the allocation are likely the result of an incomplete response buffer.
In these cases, a full reset is necessary.
When attempting to login, the ibmvnic device will allocate a response
buffer and pass a reference to the VIOS. The VIOS will then send the
ibmvnic device a LOGIN_RSP CRQ to signal that the buffer has been filled
with data. If the ibmvnic device does not get a response in 20 seconds,
the old buffer is freed and a new login request is sent. With 2
outstanding requests, any LOGIN_RSP CRQ's could be for the older
login request. If this is the case then the login response buffer (which
is for the newer login request) could be incomplete and contain invalid
data. Therefore, we must enforce strict sanity checks on the response
buffer values.
Testing has shown that the `off_rxadd_buff_size` value is filled in last
by the VIOS and will be the smoking gun for these circumstances.
Until VIOS can implement a mechanism for tracking outstanding response
buffers and a method for mapping a LOGIN_RSP CRQ to a particular login
response buffer, the best ibmvnic can do in this situation is perform a
full reset.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aab8e1a200 upstream.
Handling pci errors should fully teardown and load back auxiliary
devices, same as done through mlx5 health recovery flow.
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d006207625 upstream.
When device is in error state, marked by the flag
MLX5_DEVICE_STATE_INTERNAL_ERROR, the HW and PCI may not be accessible
and so clock update work should be skipped. Furthermore, such access
through PCI in error state, after calling mlx5_pci_disable_device() can
result in failing to recover from pci errors.
Fixes: ef9814deaf ("net/mlx5e: Add HW timestamping (TS) support")
Reported-and-tested-by: Ganesh G R <ganeshgr@linux.ibm.com>
Closes: https://lore.kernel.org/netdev/9bdb9b9d-140a-7a28-f0de-2e64e873c068@nvidia.com
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dc2b3922d upstream.
When querying eswitch functions 0 is a valid number of host VFs. After
introducing ARM SRIOV falling through to getting the max value from PCI
results in using the total VFs allowed on the ARM for the host.
Fixes: 86eec50bea ("net/mlx5: Support querying max VFs from device");
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bfe1e19fb upstream.
Fixing wrong calculation of the modify hdr pattern size,
where the previously calculated number would not be enough
to accommodate the required number of actions.
Fixes: da5d0027d6 ("net/mlx5: DR, Add cache for modify header pattern")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac5da544a3 upstream.
The flow rule can be splited, and the extra post_act rules are added
to post_act table. It's possible to trigger memleak when the rule
forwards packets from internal port and over tunnel, in the case that,
for example, CT 'new' state offload is allowed. As int_port object is
assigned to the flow attribute of post_act rule, and its refcnt is
incremented by mlx5e_tc_int_port_get(), but mlx5e_tc_int_port_put() is
not called, the refcnt is never decremented, then int_port is never
freed.
The kmemleak reports the following error:
unreferenced object 0xffff888128204b80 (size 64):
comm "handler20", pid 50121, jiffies 4296973009 (age 642.932s)
hex dump (first 32 bytes):
01 00 00 00 19 00 00 00 03 f0 00 00 04 00 00 00 ................
98 77 67 41 81 88 ff ff 98 77 67 41 81 88 ff ff .wgA.....wgA....
backtrace:
[<00000000e992680d>] kmalloc_trace+0x27/0x120
[<000000009e945a98>] mlx5e_tc_int_port_get+0x3f3/0xe20 [mlx5_core]
[<0000000035a537f0>] mlx5e_tc_add_fdb_flow+0x473/0xcf0 [mlx5_core]
[<0000000070c2cec6>] __mlx5e_add_fdb_flow+0x7cf/0xe90 [mlx5_core]
[<000000005cc84048>] mlx5e_configure_flower+0xd40/0x4c40 [mlx5_core]
[<000000004f8a2031>] mlx5e_rep_indr_offload.isra.0+0x10e/0x1c0 [mlx5_core]
[<000000007df797dc>] mlx5e_rep_indr_setup_tc_cb+0x90/0x130 [mlx5_core]
[<0000000016c15cc3>] tc_setup_cb_add+0x1cf/0x410
[<00000000a63305b4>] fl_hw_replace_filter+0x38f/0x670 [cls_flower]
[<000000008bc9e77c>] fl_change+0x1fd5/0x4430 [cls_flower]
[<00000000e7f766e4>] tc_new_tfilter+0x867/0x2010
[<00000000e101c0ef>] rtnetlink_rcv_msg+0x6fc/0x9f0
[<00000000e1111d44>] netlink_rcv_skb+0x12c/0x360
[<0000000082dd6c8b>] netlink_unicast+0x438/0x710
[<00000000fc568f70>] netlink_sendmsg+0x794/0xc50
[<0000000016e92590>] sock_sendmsg+0xc5/0x190
So fix this by moving int_port cleanup code to the flow attribute
free helper, which is used by all the attribute free cases.
Fixes: 8300f22526 ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e3d20617b upstream.
hns3_dbg_fill_content()/hclge_dbg_fill_content() is aim to integrate some
items to a string for content, and we add '\n' and '\0' in the last
two bytes of content.
strscpy() will add '\0' in the last byte of destination buffer(one of
items), it result in finishing content print ahead of schedule and some
dump content truncation.
One Error log shows as below:
cat mac_list/uc
UC MAC_LIST:
Expected:
UC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 00:2b:19:05:03:00 ACTIVE
The destination buffer is length-bounded and not required to be
NUL-terminated, so just change strscpy() to memcpy() to fix it.
Fixes: 1cf3d5567f ("net: hns3: fix strncpy() not using dest-buf length as length issue")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20230809020902.1941471-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0168042a2 upstream.
The workaround implemented in commit 3222b5b613 ("net: enetc:
initialize RFS/RSS memories for unused ports too") is no longer
effective after commit 6fffbc7ae1 ("PCI: Honor firmware's device
disabled status"). Thus, it has introduced a regression and we see AER
errors being reported again:
$ ip link set sw2p0 up && dhclient -i sw2p0 && ip addr show sw2p0
fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode
fsl_enetc 0000:00:00.2 eno2: Link is Up - 2.5Gbps/Full - flow control rx/tx
mscc_felix 0000:00:00.5 swp2: configuring for fixed/sgmii link mode
mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control off
sja1105 spi2.2 sw2p0: configuring for phy/rgmii-id link mode
sja1105 spi2.2 sw2p0: Link is Up - 1Gbps/Full - flow control off
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
pcieport 0000:00:1f.0: AER: can't find device of ID0000
Rob's suggestion is to reimplement the enetc driver workaround as a
PCI fixup, and to modify the PCI core to run the fixups for all PCI
functions. This change handles the first part.
We refactor the common code in enetc_psi_create() and enetc_psi_destroy(),
and use the PCI fixup only for those functions for which enetc_pf_probe()
won't get called. This avoids some work being done twice for the PFs
which are enabled.
Fixes: 6fffbc7ae1 ("PCI: Honor firmware's device disabled status")
Link: https://lore.kernel.org/netdev/CAL_JsqLsVYiPLx2kcHkDQ4t=hQVCR7NHziDwi9cCFUFhx48Qow@mail.gmail.com/
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac6257a3ae upstream.
When externel_lb and reset are executed together, a deadlock may
occur:
[ 3147.217009] INFO: task kworker/u321:0:7 blocked for more than 120 seconds.
[ 3147.230483] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 3147.238999] task:kworker/u321:0 state:D stack: 0 pid: 7 ppid: 2 flags:0x00000008
[ 3147.248045] Workqueue: hclge hclge_service_task [hclge]
[ 3147.253957] Call trace:
[ 3147.257093] __switch_to+0x7c/0xbc
[ 3147.261183] __schedule+0x338/0x6f0
[ 3147.265357] schedule+0x50/0xe0
[ 3147.269185] schedule_preempt_disabled+0x18/0x24
[ 3147.274488] __mutex_lock.constprop.0+0x1d4/0x5dc
[ 3147.279880] __mutex_lock_slowpath+0x1c/0x30
[ 3147.284839] mutex_lock+0x50/0x60
[ 3147.288841] rtnl_lock+0x20/0x2c
[ 3147.292759] hclge_reset_prepare+0x68/0x90 [hclge]
[ 3147.298239] hclge_reset_subtask+0x88/0xe0 [hclge]
[ 3147.303718] hclge_reset_service_task+0x84/0x120 [hclge]
[ 3147.309718] hclge_service_task+0x2c/0x70 [hclge]
[ 3147.315109] process_one_work+0x1d0/0x490
[ 3147.319805] worker_thread+0x158/0x3d0
[ 3147.324240] kthread+0x108/0x13c
[ 3147.328154] ret_from_fork+0x10/0x18
In externel_lb process, the hns3 driver call napi_disable()
first, then the reset happen, then the restore process of the
externel_lb will fail, and will not call napi_enable(). When
doing externel_lb again, napi_disable() will be double call,
cause a deadlock of rtnl_lock().
This patch use the HNS3_NIC_STATE_DOWN state to protect the
calling of napi_disable() and napi_enable() in externel_lb
process, just as the usage in ndo_stop() and ndo_start().
Fixes: 04b6ba1435 ("net: hns3: add support for external loopback test")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6265e242f7 upstream.
In some configure flow of hns3 driver, for example, change mtu, it will
disable MAC through firmware before configuration. But firmware disables
MAC asynchronously. The rx traffic may be not stopped in this case.
So fixes it by waiting until mac link is down.
Fixes: a9775bb64a ("net: hns3: fix set and get link ksettings issue")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08469dacfa upstream.
Some nic configurations could only be performed after link is down. So this
patch refactor this API for reuse.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fb1d8eb23 upstream.
Add fdir_fltr_lock locking in unprotected places.
The change in iavf_fdir_is_dup_fltr adds a spinlock around a loop which
iterates over all filters and looks for a duplicate. The filter can be
removed from list and freed from memory at the same time it's being
compared. All other places where filters are deleted are already
protected with spinlock.
The remaining changes protect adapter->fdir_active_fltr variable so now
all its uses are under a spinlock.
Fixes: 527691bf06 ("iavf: Support IPv4 Flow Director filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230807205011.3129224-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52417a95ff upstream.
ionic_start_queues_reconfig returns an error code if txrx_init fails.
Handle this error code in the relevant places.
This fixes a corner case where the device could get left in a detached
state if the CMB reconfig fails and the attempt to clean up the mess
also fails. Note that calling netif_device_attach when the netdev is
already attached does not lead to unexpected behavior.
Change goto name "errout" to "err_out" to maintain consistency across
goto statements.
Fixes: 40bc471dc7 ("ionic: add tx/rx-push support with device Component Memory Buffers")
Fixes: 6f7d6f0fd7 ("ionic: pull reset_queues into tx_timeout handler")
Signed-off-by: Nitya Sunkad <nitya.sunkad@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06b412589e upstream.
Access to shared variables through hrtimer requires locking in order
to protect the variables because actions to write into these variables
(oper_gate_closed, admin_gate_closed, and qbv_transition) might potentially
occur simultaneously. This patch provides a locking mechanisms to avoid
such scenarios.
Fixes: 175c241288 ("igc: Fix TX Hang issue when QBV Gate is closed")
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230807205129.3129346-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7dfeda6fd upstream.
When unloading the MANA driver, mana_dealloc_queues() waits for the MANA
hardware to complete any inflight packets and set the pending send count
to zero. But if the hardware has failed, mana_dealloc_queues()
could wait forever.
Fix this by adding a timeout to the wait. Set the timeout to 120 seconds,
which is a somewhat arbitrary value that is more than long enough for
functional hardware to complete any sends.
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Link: https://lore.kernel.org/r/1691576525-24271-1-git-send-email-schakrabarti@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9ffa069e0 upstream.
After merging the net-next tree, today's linux-next build (sparc64
defconfig) failed like this:
drivers/net/ethernet/sun/sunvnet_common.c: In function 'vnet_handle_offloads':
drivers/net/ethernet/sun/sunvnet_common.c:1277:16: error: implicit declaration of function 'skb_gso_segment'; did you mean 'skb_gso_reset'? [-Werror=implicit-function-declaration]
1277 | segs = skb_gso_segment(skb, dev->features & ~NETIF_F_TSO);
| ^~~~~~~~~~~~~~~
| skb_gso_reset
drivers/net/ethernet/sun/sunvnet_common.c:1277:14: warning: assignment to 'struct sk_buff *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
1277 | segs = skb_gso_segment(skb, dev->features & ~NETIF_F_TSO);
| ^
Fixes: d457a0e329 ("net: move gso declarations and functions to their own files")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230613164639.164b2991@canb.auug.org.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b755c25fbc ]
When both supported and previous version have the same major version,
and the firmwares are missing, the driver ends in a loop requesting the
same (previous) version over and over again:
[ 76.327413] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 76.339802] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.352162] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.364502] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.376848] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.389183] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.401522] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.413860] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.426199] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
...
Fix this by inverting the check to that we aren't yet at the previous
version, and also check the minor version.
This also catches the case where both versions are the same, as it was
after commit bb5dbf2cc6 ("net: marvell: prestera: add firmware v4.0
support").
With this fix applied:
[ 88.499622] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 88.511995] Prestera DX 0000:01:00.0: failed to request previous firmware: mrvl/prestera/mvsw_prestera_fw-v4.0.img
[ 88.522403] Prestera DX: probe of 0000:01:00.0 failed with error -2
Fixes: 47f26018a4 ("net: marvell: prestera: try to load previous fw version")
Signed-off-by: Jonas Gorski <jonas.gorski@bisdn.de>
Acked-by: Elad Nachman <enachman@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Taras Chornyi <taras.chornyi@plvision.eu>
Link: https://lore.kernel.org/r/20230802092357.163944-1-jonas.gorski@bisdn.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c635ca45a7 ]
In the cited commit, new type of FS_TYPE_PRIO_CHAINS fs_prio was added
to support multiple parallel namespaces for multi-chains. And we skip
all the flow tables under the fs_node of this type unconditionally,
when searching for the next or previous flow table to connect for a
new table.
As this search function is also used for find new root table when the
old one is being deleted, it will skip the entire FS_TYPE_PRIO_CHAINS
fs_node next to the old root. However, new root table should be chosen
from it if there is any table in it. Fix it by skipping only the flow
tables in the same FS_TYPE_PRIO_CHAINS fs_node when finding the
closest FT for a fs_node.
Besides, complete the connecting from FTs of previous priority of prio
because there should be multiple prevs after this fs_prio type is
introduced. And also the next FT should be chosen from the first flow
table next to the prio in the same FS_TYPE_PRIO_CHAINS fs_prio, if
this prio is the first child.
Fixes: 328edb499f ("net/mlx5: Split FDB fast path prio to multiple namespaces")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/7a95754df479e722038996c97c97b062b372591f.1690803944.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 618d28a535 ]
As find_closest_ft_recursive is called to find the closest FT, the
first parameter of find_closest_ft can be changed from fs_prio to
fs_node. Thus this function is extended to find the closest FT for the
nodes of any type, not only prios, but also the sub namespaces.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/d3962c2b443ec8dde7a740dc742a1f052d5e256c.1690803944.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c635ca45a7 ("net/mlx5: fs_core: Skip the FTs in the same FS_TYPE_PRIO_CHAINS fs_prio")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08450ea98a ]
The existing code does not allow the MTU to be set to the maximum even
after an XDP program supporting multiple buffers is attached. Fix it
to set the netdev->max_mtu to the maximum value if the attached XDP
program supports mutiple buffers, regardless of the current MTU value.
Also use a local variable dev instead of repeatedly using bp->dev.
Fixes: 1dc4c557bf ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230731142043.58855-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6974b4c2d ]
The RXBD length field on all bnxt chips is 16-bit and so we cannot
support a full page when the native page size is 64K or greater.
The non-XDP (non page pool) code path has logic to handle this but
the XDP page pool code path does not handle this. Add the missing
logic to use page_pool_dev_alloc_frag() to allocate 32K chunks if
the page size is 64K or greater.
Fixes: 9f4b28301c ("bnxt: XDP multibuffer enablement")
Link: https://lore.kernel.org/netdev/20230728231829.235716-2-michael.chan@broadcom.com/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230731142043.58855-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3bb7759a9 ]
As documented in acd7aaf51b ("netsec: ignore 'phy-mode' device
property on ACPI systems") the SocioNext SynQuacer platform ships with
firmware defining the PHY mode as RGMII even though the physical
configuration of the PHY is for TX and RX delays. Since bbc4d71d63
("net: phy: realtek: fix rtl8211e rx/tx delay config") this has caused
misconfiguration of the PHY, rendering the network unusable.
This was worked around for ACPI by ignoring the phy-mode property but
the system is also used with DT. For DT instead if we're running on a
SynQuacer force a working PHY mode, as well as the standard EDK2
firmware with DT there are also some of these systems that use u-boot
and might not initialise the PHY if not netbooting. Newer firmware
imagaes for at least EDK2 are available from Linaro so print a warning
when doing this.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731-synquacer-net-v3-1-944be5f06428@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b6291ad19 ]
in korina_probe(), the return value of clk_prepare_enable()
should be checked since it might fail. we can use
devm_clk_get_optional_enabled() instead of devm_clk_get_optional()
and clk_prepare_enable() to automatically handle the error.
Fixes: e4cd854ec4 ("net: korina: Get mdio input clock via common clock framework")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Link: https://lore.kernel.org/r/20230731090535.21416-1-ruc_gongyuanjun@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef45e8400f ]
Most kernel functions return negative error codes but some irq functions
return zero on error. In this code irq_of_parse_and_map(), returns zero
and platform_get_irq() returns negative error codes. We need to handle
both cases appropriately.
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Link: https://lore.kernel.org/r/3d0aef75-06e0-45a5-a2a6-2cc4738d4143@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 611e1b016c ]
The two mbox-related mutexes are destroyed in octep_ctrl_mbox_uninit(),
but the corresponding mutex_init calls were missing.
A "DEBUG_LOCKS_WARN_ON(lock->magic != lock)" warning was emitted with
CONFIG_DEBUG_MUTEXES on.
Initialize the two mutexes in octep_ctrl_mbox_init().
Fixes: 577f0d1b1c ("octeon_ep: add separate mailbox command and response queues")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230729151516.24153-1-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37b61cda9c ]
Similarly to other recently fixed drivers make sure we don't
try to access XDP or page pool APIs when NAPI budget is 0.
NAPI budget of 0 may mean that we are in netpoll.
This may result in running software IRQs in hard IRQ context,
leading to deadlocks or crashes.
To make sure bnapi->tx_pkts don't get wiped without handling
the events, move clearing the field into the handler itself.
Remember to clear tx_pkts after reset (bnxt_enable_napi())
as it's technically possible that netpoll will accumulate
some tx_pkts and then a reset will happen, leaving tx_pkts
out of sync with reality.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230728205020.2784844-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b31fd4d77 ]
During qdisc create/delete, it is necessary to rebuild the queue
of VSIs. An error occurred because the VSIs created by RDMA were
still active.
Added check if RDMA is active. If yes, it disallows qdisc changes
and writes a message in the system logs.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Rafal Rogalski <rafalx.rogalski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230728171243.2446101-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e346e231b4 ]
Here we've got to a situation when tasklet called usleep_range() in PTT
acquire logic, thus welcome to the "scheduling while atomic" BUG().
BUG: scheduling while atomic: swapper/24/0/0x00000100
[<ffffffffb41c6199>] schedule+0x29/0x70
[<ffffffffb41c5512>] schedule_hrtimeout_range_clock+0xb2/0x150
[<ffffffffb41c55c3>] schedule_hrtimeout_range+0x13/0x20
[<ffffffffb41c3bcf>] usleep_range+0x4f/0x70
[<ffffffffc08d3e58>] qed_ptt_acquire+0x38/0x100 [qed]
[<ffffffffc08eac48>] _qed_get_vport_stats+0x458/0x580 [qed]
[<ffffffffc08ead8c>] qed_get_vport_stats+0x1c/0xd0 [qed]
[<ffffffffc08dffd3>] qed_get_protocol_stats+0x93/0x100 [qed]
qed_mcp_send_protocol_stats
case MFW_DRV_MSG_GET_LAN_STATS:
case MFW_DRV_MSG_GET_FCOE_STATS:
case MFW_DRV_MSG_GET_ISCSI_STATS:
case MFW_DRV_MSG_GET_RDMA_STATS:
[<ffffffffc08e36d8>] qed_mcp_handle_events+0x2d8/0x890 [qed]
qed_int_assertion
qed_int_attentions
[<ffffffffc08d9490>] qed_int_sp_dpc+0xa50/0xdc0 [qed]
[<ffffffffb3aa7623>] tasklet_action+0x83/0x140
[<ffffffffb41d9125>] __do_softirq+0x125/0x2bb
[<ffffffffb41d560c>] call_softirq+0x1c/0x30
[<ffffffffb3a30645>] do_softirq+0x65/0xa0
[<ffffffffb3aa78d5>] irq_exit+0x105/0x110
[<ffffffffb41d8996>] do_IRQ+0x56/0xf0
Fix this by making caller to provide the context whether it could be in
atomic context flow or not when getting stats from QED driver.
QED driver based on the context provided decide to schedule out or not
when acquiring the PTT BAR window.
We faced the BUG_ON() while getting vport stats, but according to the
code same issue could happen for fcoe and iscsi statistics as well, so
fixing them too.
Fixes: 6c75424612 ("qed: Add support for NCSI statistics.")
Fixes: 1e128c8129 ("qed: Add support for hardware offloaded FCoE.")
Fixes: 2f2b2614e8 ("qed: Provide iSCSI statistics to management")
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: David Miller <davem@davemloft.net>
Cc: Manish Chopra <manishc@marvell.com>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0b1b2055b ]
The clock data is an array of struct clk_bulk_data, so make sure to
allocate enough memory.
Fixes: d8ca113724 ("net: stmmac: tegra: Add MGBE support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61eab651f6 ]
The cited commit sets ft prio to fs_base_prio. But if
ignore_flow_level it not supported, ft prio must be set based on
tc filter prio. Otherwise, all the ft prio are the same on the same
chain. It is invalid if ignore_flow_level is not supported.
Fix it by setting ft prio based on tc filter prio and setting
fs_base_prio to 0 for fdb.
Fixes: 8e80e56480 ("net/mlx5: fs_chains: Refactor to detach chains from tc usage")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e4cf1dd2c ]
There are DEK objects cached in DEK pool after kTLS is used, and they
are freed only in mlx5e_ktls_cleanup().
mlx5e_destroy_mdev_resources() is called in mlx5e_suspend() to
free mdev resources, including protection domain (PD). However, PD is
still referenced by the cached DEK objects in this case, because
profile->cleanup() (and therefore mlx5e_ktls_cleanup()) is called
after mlx5e_suspend() during devlink reload. So the following FW
syndrome is generated:
mlx5_cmd_out_err:803:(pid 12948): DEALLOC_PD(0x801) op_mod(0x0) failed,
status bad resource state(0x9), syndrome (0xef0c8a), err(-22)
To avoid this syndrome, move DEK pool destruction to
mlx5e_ktls_cleanup_tx(), which is called by profile->cleanup_tx(). And
move pool creation to mlx5e_ktls_init_tx() for symmetry.
Fixes: f741db1a51 ("net/mlx5e: kTLS, Improve connection rate by using fast update encryption key")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39646d9bcd ]
When the regular rq is reactivated after the XSK socket is closed
it could be reading stale cqes which eventually corrupts the rq.
This leads to no more traffic being received on the regular rq and a
crash on the next close or deactivation of the rq.
Kal Cuttler Conely reported this issue as a crash on the release
path when the xdpsock sample program is stopped (killed) and restarted
in sequence while traffic is running.
This patch flushes all cqes when during the rq flush. The cqe flushing
is done in the reset state of the rq. mlx5e_rq_to_ready code is moved
into the flush function to allow for this.
Fixes: 082a9edf12 ("net/mlx5e: xsk: Flush RQ on XSK activation to save memory")
Reported-by: Kal Cutter Conley <kal.conley@dectris.com>
Closes: https://lore.kernel.org/xdp-newbies/CAHApi-nUAs4TeFWUDV915CZJo07XVg2Vp63-no7UDfj6wur9nQ@mail.gmail.com
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93a331939d ]
The cited commit holds encap tbl lock unconditionally when setting
up dests. But it may cause the following deadlock:
PID: 1063722 TASK: ffffa062ca5d0000 CPU: 13 COMMAND: "handler8"
#0 [ffffb14de05b7368] __schedule at ffffffffa1d5aa91
#1 [ffffb14de05b7410] schedule at ffffffffa1d5afdb
#2 [ffffb14de05b7430] schedule_preempt_disabled at ffffffffa1d5b528
#3 [ffffb14de05b7440] __mutex_lock at ffffffffa1d5d6cb
#4 [ffffb14de05b74e8] mutex_lock_nested at ffffffffa1d5ddeb
#5 [ffffb14de05b74f8] mlx5e_tc_tun_encap_dests_set at ffffffffc12f2096 [mlx5_core]
#6 [ffffb14de05b7568] post_process_attr at ffffffffc12d9fc5 [mlx5_core]
#7 [ffffb14de05b75a0] mlx5e_tc_add_fdb_flow at ffffffffc12de877 [mlx5_core]
#8 [ffffb14de05b75f0] __mlx5e_add_fdb_flow at ffffffffc12e0eef [mlx5_core]
#9 [ffffb14de05b7660] mlx5e_tc_add_flow at ffffffffc12e12f7 [mlx5_core]
#10 [ffffb14de05b76b8] mlx5e_configure_flower at ffffffffc12e1686 [mlx5_core]
#11 [ffffb14de05b7720] mlx5e_rep_indr_offload at ffffffffc12e3817 [mlx5_core]
#12 [ffffb14de05b7730] mlx5e_rep_indr_setup_tc_cb at ffffffffc12e388a [mlx5_core]
#13 [ffffb14de05b7740] tc_setup_cb_add at ffffffffa1ab2ba8
#14 [ffffb14de05b77a0] fl_hw_replace_filter at ffffffffc0bdec2f [cls_flower]
#15 [ffffb14de05b7868] fl_change at ffffffffc0be6caa [cls_flower]
#16 [ffffb14de05b7908] tc_new_tfilter at ffffffffa1ab71f0
[1031218.028143] wait_for_completion+0x24/0x30
[1031218.028589] mlx5e_update_route_decap_flows+0x9a/0x1e0 [mlx5_core]
[1031218.029256] mlx5e_tc_fib_event_work+0x1ad/0x300 [mlx5_core]
[1031218.029885] process_one_work+0x24e/0x510
Actually no need to hold encap tbl lock if there is no encap action.
Fix it by checking if encap action exists or not before holding
encap tbl lock.
Fixes: 37c3b9fa7c ("net/mlx5e: Prevent encap offload when neigh update is running")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0507f2c8be ]
Currently, whenever a user is setting migratable port fn attr, the
driver is always turn migratable capability on.
Fix it by honor the user input
Fixes: e5b9642a33 ("net/mlx5: E-Switch, Implement devlink port function cmds to control migratable")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6cf0b6097 ]
The memory pointed to by the priv->rx_res pointer is not freed in the error
path of mlx5e_init_rep_rx, which can lead to a memory leak. Fix by freeing
the memory in the error path, thereby making the error path identical to
mlx5e_cleanup_rep_rx().
Fixes: af8bbf7300 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
