commit 2c507ce90e upstream.
Kernel uses `struct virtio_net_ctrl_rss` to save command-specific-data
for both the VIRTIO_NET_CTRL_MQ_HASH_CONFIG and
VIRTIO_NET_CTRL_MQ_RSS_CONFIG commands.
According to the VirtIO standard, "Field reserved MUST contain zeroes.
It is defined to make the structure to match the layout of
virtio_net_rss_config structure, defined in 5.1.6.5.7.".
Yet for the VIRTIO_NET_CTRL_MQ_HASH_CONFIG command case, the `max_tx_vq`
field in struct virtio_net_ctrl_rss, which corresponds to the
`reserved` field in struct virtio_net_hash_config, is not zeroed,
thereby violating the VirtIO standard.
This patch solves this problem by zeroing this field in
virtnet_init_default_rss().
Cc: Andrew Melnychenko <andrew@daynix.com>
Cc: stable@vger.kernel.org
Fixes: c7114b1249 ("drivers/net/virtio_net: Added basic RSS support.")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230810110405.25558-1-yin31149@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43d00e102d ]
ADQ and switchdev are not supported simultaneously. Enabling both at the
same time can result in nullptr dereference.
To prevent this, check if ADQ is active when changing devlink mode to
switchdev mode, and check if switchdev is active when enabling ADQ.
Fixes: fbc7b27af0 ("ice: enable ndo_setup_tc support for mqprio_qdisc")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230816193405.1307580-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eb9625a3a ]
While performing certain power-off sequences, PCI drivers are
called to suspend and resume their underlying devices through
PCI PM (power management) interface. However this NIC hardware
does not support PCI PM suspend/resume operations so system wide
suspend/resume leads to bad MFW (management firmware) state which
causes various follow-up errors in driver when communicating with
the device/firmware afterwards.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding
system to go into suspended/standby mode.
Without this fix device/firmware does not recover unless system
is power cycled.
Fixes: 2950219d87 ("qede: Add basic network device support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230816150711.59035-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54c9016eb8 ]
Existing comment in the source explains why we don't want efx_init_tc()
failure to be fatal. Cited commit erroneously consolidated failure
paths causing the probe to be failed in this case.
Fixes: 7e056e2360 ("sfc: obtain device mac address based on firmware handle for ef100")
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/aa7f589dd6028bd1ad49f0a85f37ab33c09b2b45.1692114888.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa165e1949 ]
In efx_init_tc(), move the setting of efx->tc->up after the
flow_indr_dev_register() call, so that if it fails, efx_fini_tc()
won't call flow_indr_dev_unregister().
Fixes: 5b2e12d51b ("sfc: bind indirect blocks for TC offload on EF100")
Suggested-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/a81284d7013aba74005277bd81104e4cfbea3f6f.1692114888.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16ca7fb9f ]
When offloading a TC encap action, the action information for the
hardware might not be "ready": if there's currently no neighbour entry
available for the destination address, we can't construct the Ethernet
header to prepend to the packet. In this case, we still offload the
flow rule, but with its action-set-list ID pointing at a "fallback"
action which simply delivers the packet to its default destination (as
though no flow rule had matched), thus allowing software TC to handle
it. Later, when we receive a neighbouring update that allows us to
construct the encap header, the rule will become "ready" and we will
update its action-set-list ID in hardware to point at the actual
offloaded actions.
This patch sets up these fallback ASLs, but does not yet use them.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: fa165e1949 ("sfc: don't unregister flow_indr if it was never registered")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23d775f12d ]
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e7 ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34a79876d9 ]
Before this fix, running high rate traffic through XDP_REDIRECT
with multibuf could overrun the fifo used to release the
xdp frames after tx completion. This resulted in corrupted data
being consumed on the free side.
The culplirt was a miscalculation of the fifo size: the maximum ratio
between fifo entries / data segments was incorrect. This ratio serves to
calculate the max fifo size for a full sq where each packet uses the
worst case number of entries in the fifo.
This patch fixes the formula and names the constant. It also makes sure
that future values will use a power of 2 number of entries for the fifo
mask to work.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Fixes: 3f734b8c59 ("net/mlx5e: XDP, Use multiple single-entry objects in xdpi_fifo")
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f2beb8874 ]
Change "write" into the actual "read" word.
Change parameters description.
Fixes: 7073f46e44 ("i40e: Add AQ commands for NVM Update for X722")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 751969e5b1 ]
Return an error if a field's mask is neither full nor empty. When a mask
is only partial the field is not being used for rule programming but it
gives a wrong impression it is used. Fix by returning an error on any
partial mask to make it clear they are not supported.
The ip_ver assignment is moved earlier in code to allow using it in
iavf_validate_fdir_fltr_masks.
Fixes: 527691bf06 ("iavf: Support IPv4 Flow Director filters")
Fixes: e90cbc257a ("iavf: Support IPv6 Flow Director filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dafcbce071 ]
Similar to commit 01f4fd2708 ("bonding: Fix incorrect deletion of
ETH_P_8021AD protocol vid from slaves"), we can trigger BUG_ON(!vlan_info)
in unregister_vlan_dev() with the following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add team1 type team
# ip netns exec ns1 ip link add team_slave type veth peer veth2
# ip netns exec ns1 ip link set team_slave master team1
# ip netns exec ns1 ip link add link team_slave name team_slave.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link team1 name team1.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set team_slave nomaster
# ip netns del ns1
Add S-VLAN tag related features support to team driver. So the team driver
will always propagate the VLAN info to its slaves.
Fixes: 8ad227ff89 ("net: vlan: add 802.1ad support")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230814032301.2804971-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 096516d092 ]
The 54810 does not support c45. The mmd_phy_indirect accesses return
arbirtary values leading to odd behavior like saying it supports EEE
when it doesn't. We also see that reading/writing these non-existent
MMD registers leads to phy instability in some cases.
Fixes: b14995ac25 ("net: phy: broadcom: Add BCM54810 PHY entry")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/1691901708-28650-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a519a5725 ]
The failure handling procedure destroys page pools for all queues,
including those that haven't had their page pool created yet. this patch
introduces necessary adjustments to prevent potential risks and
inconsistency with the error handling behavior.
Fixes: 0ebab78cbc ("net: veth: add page_pool for page recycling")
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Link: https://lore.kernel.org/r/20230812023016.10553-1-liangchen.linux@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 758c910781 ]
If it fails to get the devices's MAC address, octep_probe exits while
leaving the delayed work intr_poll_task queued. When the work later
runs, it's a use after free.
Move the cancelation of intr_poll_task from octep_remove into
octep_device_cleanup. This does not change anything in the octep_remove
flow, but octep_device_cleanup is called also in the octep_probe error
path, where the cancelation is needed.
Note that the cancelation of ctrl_mbox_task has to follow
intr_poll_task's, because the ctrl_mbox_task may be queued by
intr_poll_task.
Fixes: 24d4333233 ("octeon_ep: poll for control messages")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://lore.kernel.org/r/20230810150114.107765-5-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 607a7a45cd ]
intr_poll_task may queue ctrl_mbox_task. The function
octep_poll_non_ioq_interrupts_cn93_pf does this.
When removing the driver and canceling these two works, cancel
ctrl_mbox_task last to guarantee it does not run anymore.
Fixes: 24d4333233 ("octeon_ep: poll for control messages")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://lore.kernel.org/r/20230810150114.107765-4-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28458c8000 ]
tx_timeout_task is canceled too early when removing the driver. Nothing
prevents .ndo_tx_timeout from triggering and queuing the work again.
Better cancel it after the netdev is unregistered.
It's harmless for octep_tx_timeout_task to run in the window between the
unregistration and cancelation, because it checks netif_running.
Fixes: 862cd659a6 ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://lore.kernel.org/r/20230810150114.107765-3-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 519b227904 ]
The intention was to wait up to 500 ms for the mbox response.
The third argument to wait_event_interruptible_timeout() is supposed to
be the timeout duration. The driver mistakenly passed absolute time
instead.
Fixes: 577f0d1b1c ("octeon_ep: add separate mailbox command and response queues")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230810150114.107765-2-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c461e394d ]
On Zynq UltraScale+ MPSoC ubuntu platform when systemctl issues suspend,
network manager bring down the interface and goes into suspend. When it
wakes up it again enables the interface.
This leads to xilinx-psgtr "PLL lock timeout" on interface bringup, as
the power management controller power down the entire FPD (including
SERDES) if none of the FPD devices are in use and serdes is not
initialized on resume.
$ sudo rtcwake -m no -s 120 -v
$ sudo systemctl suspend <this does ifconfig eth1 down>
$ ifconfig eth1 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
macb driver is called in this way:
1. macb_close: Stop network interface. In this function, it
reset MACB IP and disables PHY and network interface.
2. macb_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into suspend state. Some time later, system is
waken up by RTC wakeup device;
4. macb_resume: It does nothing because network interface has
been disabled;
5. macb_open: It is called to enable network interface again. ethernet
interface is initialized in this API but serdes which is power-off
by PMUFW during FPD-off suspend is not initialized again and so
we hit GT PLL lock issue on open.
To resolve this PLL timeout issue always do PS GTR initialization
when ethernet device is configured as non-wakeup source.
Fixes: f22bd29ba1 ("net: macb: Fix ZynqMP SGMII non-wakeup source resume failure")
Fixes: 8b73fa3ae0 ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1691414091-2260697-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc941e548b ]
Uwe reports:
"Most PHYs signal WoL using an interrupt. So disabling interrupts [at
shutdown] breaks WoL at least on PHYs covered by the marvell driver."
Discussing with Ioana, the problem which was trying to be solved was:
"The board in question is a LS1021ATSN which has two AR8031 PHYs that
share an interrupt line. In case only one of the PHYs is probed and
there are pending interrupts on the PHY#2 an IRQ storm will happen
since there is no entity to clear the interrupt from PHY#2's registers.
PHY#1's driver will get stuck in .handle_interrupt() indefinitely."
Further confirmation that "the two AR8031 PHYs are on the same MDIO
bus."
With WoL using interrupts to wake the system, in such a case, the
system will begin booting with an asserted interrupt. Thus, we need to
cope with an interrupt asserted during boot.
Solve this instead by disabling interrupts during PHY probe. This will
ensure in Ioana's situation that both PHYs of the same type sharing an
interrupt line on a common MDIO bus will have their interrupt outputs
disabled when the driver probes the device, but before we hook in any
interrupt handlers - thus avoiding the interrupt storm.
A better fix would be for platform firmware to disable the interrupting
devices at source during boot, before control is handed to the kernel.
Fixes: e2f016cf77 ("net: phy: add a shutdown procedure")
Link: 20230804071757.383971-1-u.kleine-koenig@pengutronix.de
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829c6524d6 ]
The reference of pdev->dev is taken by of_find_device_by_node, so
it should be released when not need anymore.
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Signed-off-by: Xiang Yang <xiangyang3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51b813176f ]
Commit 25266128fe ("virtio-net: fix race between set queues and
probe") tries to fix the race between set queues and probe by calling
_virtnet_set_queues() before DRIVER_OK is set. This violates virtio
spec. Fixing this by setting queues after virtio_device_ready().
Note that rtnl needs to be held for userspace requests to change the
number of queues. So we are serialized in this way.
Fixes: 25266128fe ("virtio-net: fix race between set queues and probe")
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2145328515 ]
With RX coalescing, one CQE entry can be used to indicate multiple packets
on the receive queue. This saves processing time and PCI bandwidth over
the CQ.
The MANA Ethernet driver also uses the v2 version of the protocol. It
doesn't use RX coalescing and its behavior is not changed.
Link: https://lore.kernel.org/r/1684045095-31228-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e58f30246c ]
In commit 7beecaf7d5 ("net: phy: at803x: improve the WOL feature"), it
seems not correct to use a wol_en bit in a 1588 Control Register which is
only available on AR8031/AR8033(share the same phy_id) to determine if WoL
is enabled. Change it back to use AT803X_INTR_ENABLE_WOL for determining
the WoL status which is applicable on all chips supporting wol. Also update
the at803x_set_wol() function to only update the 1588 register on chips
having it. After this change, disabling wol at probe from commit
d7cd5e06c9 ("net: phy: at803x: disable WOL at probe") is no longer
needed. Change it to just disable the WoL bit in 1588 register for
AR8031/AR8033 to be aligned with AT803X_INTR_ENABLE_WOL in probe.
Fixes: 7beecaf7d5 ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 988e8d90b3 ]
Use devm_regulator_get_enable_optional() instead of hand writing it. It
saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: e58f30246c ("net: phy: at803x: fix the wol setting functions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6db541ae27 upstream.
If a login request fails, the recovery process should be protected
against parallel resets. It is a known issue that freeing and
registering CRQ's in quick succession can result in a failover CRQ from
the VIOS. Processing a failover during login recovery is dangerous for
two reasons:
1. This will result in two parallel initialization processes, this can
cause serious issues during login.
2. It is possible that the failover CRQ is received but never executed.
We get notified of a pending failover through a transport event CRQ.
The reset is not performed until a INIT CRQ request is received.
Previously, if CRQ init fails during login recovery, then the ibmvnic
irq is freed and the login process returned error. If failover_pending
is true (a transport event was received), then the ibmvnic device
would never be able to process the reset since it cannot receive the
CRQ_INIT request due to the irq being freed. This leaved the device
in a inoperable state.
Therefore, the login failure recovery process must be hardened against
these possible issues. Possible failovers (due to quick CRQ free and
init) must be avoided and any issues during re-initialization should be
dealt with instead of being propagated up the stack. This logic is
similar to that of ibmvnic_probe().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-5-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23cc5f6674 upstream.
Perform a partial reset before sending a login request if any of the
following are true:
1. If a previous request times out. This can be dangerous because the
VIOS could still receive the old login request at any point after
the timeout. Therefore, it is best to re-register the CRQ's and
sub-CRQ's before retrying.
2. If the previous request returns an error that is not described in
PAPR. PAPR provides procedures if the login returns with partial
success or aborted return codes (section L.5.1) but other values
do not have a defined procedure. Previously, these conditions
just returned error from the login function rather than trying
to resolve the issue.
This can cause further issues since most callers of the login
function are not prepared to handle an error when logging in. This
improper cleanup can lead to the device being permanently DOWN'd.
For example, if the VIOS believes that the device is already logged
in then it will return INVALID_STATE (-7). If we never re-register
CRQ's then it will always think that the device is already logged
in. This leaves the device inoperable.
The partial reset involves freeing the sub-CRQs, freeing the CRQ then
registering and initializing a new CRQ and sub-CRQs. This essentially
restarts all communication with VIOS to allow for a fresh login attempt
that will be unhindered by any previous failed attempts.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-4-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d78a671eb8 upstream.
Rather than leaving the DMA unmapping of the login buffers to the
login response handler, move this work into the login release functions.
Previously, these functions were only used for freeing the allocated
buffers. This could lead to issues if there are more than one
outstanding login buffer requests, which is possible if a login request
times out.
If a login request times out, then there is another call to send login.
The send login function makes a call to the login buffer release
function. In the past, this freed the buffers but did not DMA unmap.
Therefore, the VIOS could still write to the old login (now freed)
buffer. It is for this reason that it is a good idea to leave the DMA
unmap call to the login buffers release function.
Since the login buffer release functions now handle DMA unmapping,
remove the duplicate DMA unmapping in handle_login_rsp().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-3-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 411c565b4b upstream.
If the LOGIN CRQ fails to send then we must DMA unmap the response
buffer. Previously, if the CRQ failed then the memory was freed without
DMA unmapping.
Fixes: c98d9cc417 ("ibmvnic: send_login should check for crq errors")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db17ba719b upstream.
Ensure that all offsets in a login response buffer are within the size
of the allocated response buffer. Any offsets or lengths that surpass
the allocation are likely the result of an incomplete response buffer.
In these cases, a full reset is necessary.
When attempting to login, the ibmvnic device will allocate a response
buffer and pass a reference to the VIOS. The VIOS will then send the
ibmvnic device a LOGIN_RSP CRQ to signal that the buffer has been filled
with data. If the ibmvnic device does not get a response in 20 seconds,
the old buffer is freed and a new login request is sent. With 2
outstanding requests, any LOGIN_RSP CRQ's could be for the older
login request. If this is the case then the login response buffer (which
is for the newer login request) could be incomplete and contain invalid
data. Therefore, we must enforce strict sanity checks on the response
buffer values.
Testing has shown that the `off_rxadd_buff_size` value is filled in last
by the VIOS and will be the smoking gun for these circumstances.
Until VIOS can implement a mechanism for tracking outstanding response
buffers and a method for mapping a LOGIN_RSP CRQ to a particular login
response buffer, the best ibmvnic can do in this situation is perform a
full reset.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aab8e1a200 upstream.
Handling pci errors should fully teardown and load back auxiliary
devices, same as done through mlx5 health recovery flow.
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d006207625 upstream.
When device is in error state, marked by the flag
MLX5_DEVICE_STATE_INTERNAL_ERROR, the HW and PCI may not be accessible
and so clock update work should be skipped. Furthermore, such access
through PCI in error state, after calling mlx5_pci_disable_device() can
result in failing to recover from pci errors.
Fixes: ef9814deaf ("net/mlx5e: Add HW timestamping (TS) support")
Reported-and-tested-by: Ganesh G R <ganeshgr@linux.ibm.com>
Closes: https://lore.kernel.org/netdev/9bdb9b9d-140a-7a28-f0de-2e64e873c068@nvidia.com
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dc2b3922d upstream.
When querying eswitch functions 0 is a valid number of host VFs. After
introducing ARM SRIOV falling through to getting the max value from PCI
results in using the total VFs allowed on the ARM for the host.
Fixes: 86eec50bea ("net/mlx5: Support querying max VFs from device");
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bfe1e19fb upstream.
Fixing wrong calculation of the modify hdr pattern size,
where the previously calculated number would not be enough
to accommodate the required number of actions.
Fixes: da5d0027d6 ("net/mlx5: DR, Add cache for modify header pattern")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac5da544a3 upstream.
The flow rule can be splited, and the extra post_act rules are added
to post_act table. It's possible to trigger memleak when the rule
forwards packets from internal port and over tunnel, in the case that,
for example, CT 'new' state offload is allowed. As int_port object is
assigned to the flow attribute of post_act rule, and its refcnt is
incremented by mlx5e_tc_int_port_get(), but mlx5e_tc_int_port_put() is
not called, the refcnt is never decremented, then int_port is never
freed.
The kmemleak reports the following error:
unreferenced object 0xffff888128204b80 (size 64):
comm "handler20", pid 50121, jiffies 4296973009 (age 642.932s)
hex dump (first 32 bytes):
01 00 00 00 19 00 00 00 03 f0 00 00 04 00 00 00 ................
98 77 67 41 81 88 ff ff 98 77 67 41 81 88 ff ff .wgA.....wgA....
backtrace:
[<00000000e992680d>] kmalloc_trace+0x27/0x120
[<000000009e945a98>] mlx5e_tc_int_port_get+0x3f3/0xe20 [mlx5_core]
[<0000000035a537f0>] mlx5e_tc_add_fdb_flow+0x473/0xcf0 [mlx5_core]
[<0000000070c2cec6>] __mlx5e_add_fdb_flow+0x7cf/0xe90 [mlx5_core]
[<000000005cc84048>] mlx5e_configure_flower+0xd40/0x4c40 [mlx5_core]
[<000000004f8a2031>] mlx5e_rep_indr_offload.isra.0+0x10e/0x1c0 [mlx5_core]
[<000000007df797dc>] mlx5e_rep_indr_setup_tc_cb+0x90/0x130 [mlx5_core]
[<0000000016c15cc3>] tc_setup_cb_add+0x1cf/0x410
[<00000000a63305b4>] fl_hw_replace_filter+0x38f/0x670 [cls_flower]
[<000000008bc9e77c>] fl_change+0x1fd5/0x4430 [cls_flower]
[<00000000e7f766e4>] tc_new_tfilter+0x867/0x2010
[<00000000e101c0ef>] rtnetlink_rcv_msg+0x6fc/0x9f0
[<00000000e1111d44>] netlink_rcv_skb+0x12c/0x360
[<0000000082dd6c8b>] netlink_unicast+0x438/0x710
[<00000000fc568f70>] netlink_sendmsg+0x794/0xc50
[<0000000016e92590>] sock_sendmsg+0xc5/0x190
So fix this by moving int_port cleanup code to the flow attribute
free helper, which is used by all the attribute free cases.
Fixes: 8300f22526 ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e3d20617b upstream.
hns3_dbg_fill_content()/hclge_dbg_fill_content() is aim to integrate some
items to a string for content, and we add '\n' and '\0' in the last
two bytes of content.
strscpy() will add '\0' in the last byte of destination buffer(one of
items), it result in finishing content print ahead of schedule and some
dump content truncation.
One Error log shows as below:
cat mac_list/uc
UC MAC_LIST:
Expected:
UC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 00:2b:19:05:03:00 ACTIVE
The destination buffer is length-bounded and not required to be
NUL-terminated, so just change strscpy() to memcpy() to fix it.
Fixes: 1cf3d5567f ("net: hns3: fix strncpy() not using dest-buf length as length issue")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20230809020902.1941471-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0168042a2 upstream.
The workaround implemented in commit 3222b5b613 ("net: enetc:
initialize RFS/RSS memories for unused ports too") is no longer
effective after commit 6fffbc7ae1 ("PCI: Honor firmware's device
disabled status"). Thus, it has introduced a regression and we see AER
errors being reported again:
$ ip link set sw2p0 up && dhclient -i sw2p0 && ip addr show sw2p0
fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode
fsl_enetc 0000:00:00.2 eno2: Link is Up - 2.5Gbps/Full - flow control rx/tx
mscc_felix 0000:00:00.5 swp2: configuring for fixed/sgmii link mode
mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control off
sja1105 spi2.2 sw2p0: configuring for phy/rgmii-id link mode
sja1105 spi2.2 sw2p0: Link is Up - 1Gbps/Full - flow control off
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
pcieport 0000:00:1f.0: AER: can't find device of ID0000
Rob's suggestion is to reimplement the enetc driver workaround as a
PCI fixup, and to modify the PCI core to run the fixups for all PCI
functions. This change handles the first part.
We refactor the common code in enetc_psi_create() and enetc_psi_destroy(),
and use the PCI fixup only for those functions for which enetc_pf_probe()
won't get called. This avoids some work being done twice for the PFs
which are enabled.
Fixes: 6fffbc7ae1 ("PCI: Honor firmware's device disabled status")
Link: https://lore.kernel.org/netdev/CAL_JsqLsVYiPLx2kcHkDQ4t=hQVCR7NHziDwi9cCFUFhx48Qow@mail.gmail.com/
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac6257a3ae upstream.
When externel_lb and reset are executed together, a deadlock may
occur:
[ 3147.217009] INFO: task kworker/u321:0:7 blocked for more than 120 seconds.
[ 3147.230483] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 3147.238999] task:kworker/u321:0 state:D stack: 0 pid: 7 ppid: 2 flags:0x00000008
[ 3147.248045] Workqueue: hclge hclge_service_task [hclge]
[ 3147.253957] Call trace:
[ 3147.257093] __switch_to+0x7c/0xbc
[ 3147.261183] __schedule+0x338/0x6f0
[ 3147.265357] schedule+0x50/0xe0
[ 3147.269185] schedule_preempt_disabled+0x18/0x24
[ 3147.274488] __mutex_lock.constprop.0+0x1d4/0x5dc
[ 3147.279880] __mutex_lock_slowpath+0x1c/0x30
[ 3147.284839] mutex_lock+0x50/0x60
[ 3147.288841] rtnl_lock+0x20/0x2c
[ 3147.292759] hclge_reset_prepare+0x68/0x90 [hclge]
[ 3147.298239] hclge_reset_subtask+0x88/0xe0 [hclge]
[ 3147.303718] hclge_reset_service_task+0x84/0x120 [hclge]
[ 3147.309718] hclge_service_task+0x2c/0x70 [hclge]
[ 3147.315109] process_one_work+0x1d0/0x490
[ 3147.319805] worker_thread+0x158/0x3d0
[ 3147.324240] kthread+0x108/0x13c
[ 3147.328154] ret_from_fork+0x10/0x18
In externel_lb process, the hns3 driver call napi_disable()
first, then the reset happen, then the restore process of the
externel_lb will fail, and will not call napi_enable(). When
doing externel_lb again, napi_disable() will be double call,
cause a deadlock of rtnl_lock().
This patch use the HNS3_NIC_STATE_DOWN state to protect the
calling of napi_disable() and napi_enable() in externel_lb
process, just as the usage in ndo_stop() and ndo_start().
Fixes: 04b6ba1435 ("net: hns3: add support for external loopback test")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6265e242f7 upstream.
In some configure flow of hns3 driver, for example, change mtu, it will
disable MAC through firmware before configuration. But firmware disables
MAC asynchronously. The rx traffic may be not stopped in this case.
So fixes it by waiting until mac link is down.
Fixes: a9775bb64a ("net: hns3: fix set and get link ksettings issue")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08469dacfa upstream.
Some nic configurations could only be performed after link is down. So this
patch refactor this API for reuse.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a94c16a2fd upstream.
When the tagging protocol in current use is "ocelot-8021q" and we unbind
the driver, we see this splat:
$ echo '0000:00:00.2' > /sys/bus/pci/drivers/fsl_enetc/unbind
mscc_felix 0000:00:00.5 swp0: left promiscuous mode
sja1105 spi2.0: Link is Down
DSA: tree 1 torn down
mscc_felix 0000:00:00.5 swp2: left promiscuous mode
sja1105 spi2.2: Link is Down
DSA: tree 3 torn down
fsl_enetc 0000:00:00.2 eno2: left promiscuous mode
mscc_felix 0000:00:00.5: Link is Down
------------[ cut here ]------------
RTNL: assertion failed at net/dsa/tag_8021q.c (409)
WARNING: CPU: 1 PID: 329 at net/dsa/tag_8021q.c:409 dsa_tag_8021q_unregister+0x12c/0x1a0
Modules linked in:
CPU: 1 PID: 329 Comm: bash Not tainted 6.5.0-rc3+ #771
pc : dsa_tag_8021q_unregister+0x12c/0x1a0
lr : dsa_tag_8021q_unregister+0x12c/0x1a0
Call trace:
dsa_tag_8021q_unregister+0x12c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
RTNL: assertion failed at net/8021q/vlan_core.c (376)
WARNING: CPU: 1 PID: 329 at net/8021q/vlan_core.c:376 vlan_vid_del+0x1b8/0x1f0
CPU: 1 PID: 329 Comm: bash Tainted: G W 6.5.0-rc3+ #771
pc : vlan_vid_del+0x1b8/0x1f0
lr : vlan_vid_del+0x1b8/0x1f0
dsa_tag_8021q_unregister+0x8c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
DSA: tree 0 torn down
This was somewhat not so easy to spot, because "ocelot-8021q" is not the
default tagging protocol, and thus, not everyone who tests the unbinding
path may have switched to it beforehand. The default
felix_tag_npi_teardown() does not require rtnl_lock() to be held.
Fixes: 7c83a7c539 ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230803134253.2711124-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7791cec23 upstream.
Since the AR8032 part does not support wol, remove related callbacks
from it.
Fixes: 5800091a20 ("net: phy: at803x: add support for AR8032 PHY")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fb1d8eb23 upstream.
Add fdir_fltr_lock locking in unprotected places.
The change in iavf_fdir_is_dup_fltr adds a spinlock around a loop which
iterates over all filters and looks for a duplicate. The filter can be
removed from list and freed from memory at the same time it's being
compared. All other places where filters are deleted are already
protected with spinlock.
The remaining changes protect adapter->fdir_active_fltr variable so now
all its uses are under a spinlock.
Fixes: 527691bf06 ("iavf: Support IPv4 Flow Director filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230807205011.3129224-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1c936e9af upstream.
In case rhashtable_lookup_insert_fast() fails inside vxlan_vni_add(), the
allocated percpu vni stats are not freed on the error path.
Introduce vxlan_vni_free() which would work as a nice wrapper to free
vxlan_vni_node resources properly.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4095e0e132 ("drivers: vxlan: vnifilter: per vni stats")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59eeb23294 upstream.
Using the syzkaller repro with reduced packet size it was discovered
that XDP_PACKET_HEADROOM is not checked in tun_can_build_skb(),
although pad may be incremented in tun_build_skb(). This may end up
with exceeding the PAGE_SIZE limit in tun_build_skb().
Jason Wang <jasowang@redhat.com> proposed to count XDP_PACKET_HEADROOM
always (e.g. without rcu_access_pointer(tun->xdp_prog)) in
tun_can_build_skb() since there's a window during which XDP program
might be attached between tun_can_build_skb() and tun_build_skb().
Fixes: 7df13219d7 ("tun: reserve extra headroom only when XDP is set")
Link: https://syzkaller.appspot.com/bug?extid=f817490f5bd20541b90a
Signed-off-by: Andrew Kanner <andrew.kanner@gmail.com>
Link: https://lore.kernel.org/r/20230803185947.2379988-1-andrew.kanner@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01f4fd2708 upstream.
BUG_ON(!vlan_info) is triggered in unregister_vlan_dev() with
following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add bond0 type bond mode 0
# ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
# ip netns exec ns1 ip link set bond_slave_1 master bond0
# ip netns exec ns1 ip link add link bond_slave_1 name vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link bond0 name bond0_vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set bond_slave_1 nomaster
# ip netns del ns1
The logical analysis of the problem is as follows:
1. create ETH_P_8021AD protocol vlan10 for bond_slave_1:
register_vlan_dev()
vlan_vid_add()
vlan_info_alloc()
__vlan_vid_add() // add [ETH_P_8021AD, 10] vid to bond_slave_1
2. create ETH_P_8021AD protocol bond0_vlan10 for bond0:
register_vlan_dev()
vlan_vid_add()
__vlan_vid_add()
vlan_add_rx_filter_info()
if (!vlan_hw_filter_capable(dev, proto)) // condition established because bond0 without NETIF_F_HW_VLAN_STAG_FILTER
return 0;
if (netif_device_present(dev))
return dev->netdev_ops->ndo_vlan_rx_add_vid(dev, proto, vid); // will be never called
// The slaves of bond0 will not refer to the [ETH_P_8021AD, 10] vid.
3. detach bond_slave_1 from bond0:
__bond_release_one()
vlan_vids_del_by_dev()
list_for_each_entry(vid_info, &vlan_info->vid_list, list)
vlan_vid_del(dev, vid_info->proto, vid_info->vid);
// bond_slave_1 [ETH_P_8021AD, 10] vid will be deleted.
// bond_slave_1->vlan_info will be assigned NULL.
4. delete vlan10 during delete ns1:
default_device_exit_batch()
dev->rtnl_link_ops->dellink() // unregister_vlan_dev() for vlan10
vlan_info = rtnl_dereference(real_dev->vlan_info); // real_dev of vlan10 is bond_slave_1
BUG_ON(!vlan_info); // bond_slave_1->vlan_info is NULL now, bug is triggered!!!
Add S-VLAN tag related features support to bond driver. So the bond driver
will always propagate the VLAN info to its slaves.
Fixes: 8ad227ff89 ("net: vlan: add 802.1ad support")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230802114320.4156068-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
