[ Upstream commit 53d061c19d ]
USB PHY DPDM wakeup bit is enabled by default, when USB wakeup
is not required(/sys/.../wakeup is disabled), this bit should be
disabled, otherwise we will have unexpected wakeup if do USB device
connect/disconnect while system sleep.
This bit can be enabled for both host and device mode.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230517081907.3410465-3-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ac37fbdad ]
As we use bvalid for vbus wakeup source, to save power when
suspend, turn off the vbus comparator for imx7d and imx8mm.
Below is this bit description from RM of iMX8MM
"VBUS Valid Comparator Enable:
This signal controls the USB OTG PHY VBUS Valid comparator which
indicates whether the voltage on the USB_OTG*_VBUS pin is below
the VBUS Valid threshold. The VBUS Valid threshold is nominally
4.75V on this USB PHY. The VBUS Valid threshold can be adjusted
using the USBNC_OTGn_PHY_CFG1[OTGTUNE0] bit field. Status of the
VBUS Valid comparator, when it is enabled, is reported on the
USBNC_OTGn_PHY_STATUS[VBUS_VLD] bit.
When OTGDISABLE0 (USBNC_USB_OTGx_PHY_CFG2[10])is set to 1'b0 and
DRVVBUS0 is set to 1'b1, the Bandgap circuitry and VBUS Valid
comparator are powered, even in Suspend or Sleep mode.
DRVVBUS0 should be reset to 1'b0 when the internal VBUS Valid comparator
is not required, to reduce quiescent current in Suspend or Sleep mode.
- 0 The VBUS Valid comparator is disabled
- 1 The VBUS Valid comparator is enabled"
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230517081907.3410465-2-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a070e8e20 ]
Use dedicated imx8ulp usb compatible to remove QoS request
since imx8ulp has no such limitation of imx7ulp: DMA will
not work if system enters idle.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230530104007.1294702-2-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a4776205b ]
The XHCI_PLAT quirk was only needed to ensure non-PCI xHC host avoided
setting up MSI interrupts in generic xhci codepaths.
The MSI setup code is now moved to PCI specific xhci-pci.c file so
the quirk is no longer needed.
Remove setting the XHCI_PLAT quirk for HiSilocon SoC xHC, NVIDIA Tegra xHC,
MediaTek xHC, the generic xhci-plat driver, and the checks for XHCI_PLAT
in xhci-pci.c MSI setup code.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-5-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3ff12a92b ]
ISOC transfers expect a certain cadence of requests being queued. Not
keeping up with the expected rate of requests results in missed ISOC
transfers (EXDEV). The application layer may or may not produce video
frames to match this expectation, so uvc gadget driver must handle cases
where the application is not queuing up buffers fast enough to fulfill
ISOC requirements.
Currently, uvc gadget driver waits for new video buffer to become available
before queuing up usb requests. With this patch the gadget driver queues up
0 length usb requests whenever there are no video buffers available. The
USB controller's complete callback is used as the limiter for how quickly
the 0 length packets will be queued. Video buffers are still queued as
soon as they become available.
Link: https://lore.kernel.org/CAMHf4WKbi6KBPQztj9FA4kPvESc1fVKrC8G73-cs6tTeQby9=w@mail.gmail.com/
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20230508231103.1621375-1-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e599046994 ]
When serial console over USB is enabled, gs_console_connect
queues gs_console_work, where it acquires the spinlock and
queues the usb request, and this request goes to gadget layer.
Now consider a situation where gadget layer prints something
to dmesg, this will eventually call gs_console_write() which
requires cons->lock. And this causes spinlock recursion. Avoid
this by excluding usb_ep_queue from the spinlock.
spin_lock_irqsave //needs cons->lock
gs_console_write
.
.
_printk
__warn_printk
dev_warn/pr_err
.
.
[USB Gadget Layer]
.
.
usb_ep_queue
gs_console_work
__gs_console_push // acquires cons->lock
process_one_work
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1683638872-6885-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5a5ccd61cf upstream.
When connecting to some DisplayPort partners, the initial status update
after entering DisplayPort Alt Mode notifies that the DFP_D/UFP_D is not in
the connected state. This leads to sending a configure message that keeps
the device in USB mode. The port partner then sets DFP_D/UFP_D to the
connected state and HPD to high in the same Attention message. Currently,
the HPD signal is dropped in order to handle configuration.
This patch saves changes to the HPD signal when the device chooses to
configure during dp_altmode_status_update, and invokes sysfs_notify if
necessary for HPD after configuring.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230726020903.1409072-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4270d2b484 upstream.
Do not transition to SNK_UNATTACHED state when receiving vsafe0v event
while in SNK_HARD_RESET_WAIT_VBUS. Ignore VBUS off events as well as
in some platforms VBUS off can be signalled more than once.
[143515.364753] Requesting mux state 1, usb-role 2, orientation 2
[143515.365520] pending state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_SINK_ON @ 650 ms [rev3 HARD_RESET]
[143515.632281] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_HARD_RESET_SINK_OFF, polarity 1, disconnected]
[143515.637214] VBUS on
[143515.664985] VBUS off
[143515.664992] state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_WAIT_VBUS [rev3 HARD_RESET]
[143515.665564] VBUS VSAFE0V
[143515.665566] state change SNK_HARD_RESET_WAIT_VBUS -> SNK_UNATTACHED [rev3 HARD_RESET]
Fixes: 28b43d3d74 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: <stable@vger.kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230712085722.1414743-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e21a620c7 upstream.
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() because last_role is same
as current role. This happens since last_role gets initialised
to zero during the probe.
To avoid this, add a new flag initial_detection into struct
usb_conn_info, which prevents bailing out during initial
detection.
Cc: <stable@vger.kernel.org> # 5.4
Fixes: 4602f3bff2 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/1690880632-12588-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65dadb2bee upstream.
Avichal Rakesh reported a kernel panic that occurred when the UVC
gadget driver was removed from a gadget's configuration. The panic
involves a somewhat complicated interaction between the kernel driver
and a userspace component (as described in the Link tag below), but
the analysis did make one thing clear: The Gadget core should
accomodate gadget drivers calling usb_gadget_deactivate() as part of
their unbind procedure.
Currently this doesn't work. gadget_unbind_driver() calls
driver->unbind() while holding the udc->connect_lock mutex, and
usb_gadget_deactivate() attempts to acquire that mutex, which will
result in a deadlock.
The simple fix is for gadget_unbind_driver() to release the mutex when
invoking the ->unbind() callback. There is no particular reason for
it to be holding the mutex at that time, and the mutex isn't held
while the ->bind() callback is invoked. So we'll drop the mutex
before performing the unbind callback and reacquire it afterward.
We'll also add a couple of comments to usb_gadget_activate() and
usb_gadget_deactivate(). Because they run in process context they
must not be called from a gadget driver's ->disconnect() callback,
which (according to the kerneldoc for struct usb_gadget_driver in
include/linux/usb/gadget.h) may run in interrupt context. This may
help prevent similar bugs from arising in the future.
Reported-and-tested-by: Avichal Rakesh <arakesh@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 286d9975a8 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
Link: https://lore.kernel.org/linux-usb/4d7aa3f4-22d9-9f5a-3d70-1bd7148ff4ba@google.com/
Cc: Badhri Jagan Sridharan <badhri@google.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/48b2f1f1-0639-46bf-bbfc-98cb05a24914@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ddaa6a274 upstream.
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Cc: stable@vger.kernel.org
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ff6e7a9d upstream.
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead.
Reported-and-tested-by: syzbot+e7d46eb426883fb97efd@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/0000000000007d25ff059457342d@google.com/T/
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: e80b0fade0 ("[PATCH] USB Storage: add alauda support")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/693d5d5e-f09b-42d0-8ed9-1f96cd30bcce@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 288b4fa179 upstream.
This reverts commit 18fc7c435b.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this code, the patch means that certain tegra_xusb_probe() will
fail if the firmware supports power-domains but CONFIG_PM is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 18fc7c435b ("usb: xhci: tegra: Fix error check")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/8baace8d-fb4b-41a4-ad5f-848ae643a23b@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2627335a13 upstream.
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e0 ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dc162e223 upstream.
The Focusrite Scarlett audio device does not behave correctly during
resumes. Below is what happens during every resume (captured with
Beagle 5000):
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset/Target disconnected>
<High Speed>
The Scarlett disconnects and is enumerated again.
However from time to time it drops completely off the USB bus during
resume. Below is captured occurrence of such an event:
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset>/<Chirp K>/<Tiny K>
<High Speed>
<Corrupted packet>
<Reset/Target disconnected>
To fix the condition a user has to unplug and plug the device again.
With USB_QUIRK_RESET_RESUME applied ("usbcore.quirks=1235:8211:b")
for the Scarlett audio device the issue still reproduces.
Applying USB_QUIRK_DISCONNECT_SUSPEND ("usbcore.quirks=1235:8211:m")
fixed the issue and the Scarlett audio device didn't drop off the USB
bus for ~5000 suspend/resume cycles where originally issue reproduced in
~100 or less suspend/resume cycles.
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230724112911.1802577-1-lb@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c55afcbeaa upstream.
The ohci_hcd_at91_drv_suspend() sets ohci->rh_state to OHCI_RH_HALTED when
suspend which will let the ohci_irq() skip the interrupt after resume. And
nobody to handle this interrupt.
According to the comment in ohci_hcd_at91_drv_suspend(), it need to reset
when resume from suspend(MEM) to fix by setting "hibernated" argument of
ohci_resume().
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230626152713.18950-1-aarongt.shen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f2327666a upstream.
A negative number from ret means the host controller had failed to send
usb message and 0 means succeed. Therefore, the if logic is wrong here
and this patch will fix it.
Fixes: f2b42379c5 ("usb: misc: ehset: Rework test mode entry")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230705095231.457860-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e835c0a4e2 upstream.
Commit c4a5153e87 ("usb: dwc3: core: Power-off core/PHYs on
system_suspend in host mode") replaces check for HOST only dr_mode with
current_dr_role. But during booting, the current_dr_role isn't
initialized, thus the device side reset is always issued even if dwc3
was configured as host-only. What's more, on some platforms with host
only dwc3, aways issuing device side reset by accessing device register
block can cause kernel panic.
Fixes: c4a5153e87 ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b32b8f2b95 upstream.
Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for
USB device-mode. The phy chip usually has its 'reset' and 'chip select'
lines connected to GPIOs described by ACPI fwnodes in the DSDT table.
Because of hardware with missing ACPI resources for the 'reset' and 'chip
select' GPIOs commit 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table
on platforms without ACPI GPIO resources") introduced a fallback
gpiod_lookup_table with hard-coded mappings for Bay Trail devices.
However there are existing Bay Trail based devices, like the National
Instruments cRIO-903x series, where the phy chip has its 'reset' and
'chip-select' lines always asserted in hardware via resistor pull-ups. On
this hardware the phy chip is always enabled and the ACPI dsdt table is
missing information not only for the 'chip-select' and 'reset' lines but
also for the BYT GPIO controller itself "INT33FC".
With the introduction of the gpiod_lookup_table initializing the USB
device-mode on these hardware now errors out. The error comes from the
gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an
-ENOENT error due to the missing ACPI entry for the INT33FC gpio controller
used in the aforementioned table.
This hardware used to work before because gpiod_get_optional() will return
NULL instead of -ENOENT if no GPIO has been assigned to the requested
function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs
was then skipped (due to the NULL return). This is the correct behavior in
cases where the phy chip is hardwired and there are no GPIOs to control.
Since the gpiod_lookup_table relies on the presence of INT33FC fwnode
in ACPI tables only add the table if we know the entry for the INT33FC
gpio controller is present. This allows Bay Trail based devices with
hardwired dwc3 ULPI phys to continue working.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@kernel.org>
Signed-off-by: Gratian Crisan <gratian.crisan@ni.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 734ae15ab9 upstream.
This reverts commit b138e23d3d.
AutoRetry has been found to sometimes cause controller freezes when
communicating with buggy USB devices.
This controller feature allows the controller in host mode to send
non-terminating/burst retry ACKs instead of terminating retry ACKs
to devices when a transaction error (CRC error or overflow) occurs.
Unfortunately, if the USB device continues to respond with a CRC error,
the controller will not complete endpoint-related commands while it
keeps trying to auto-retry. [3] The xHCI driver will notice this once
it tries to abort the transfer using a Stop Endpoint command and
does not receive a completion in time. [1]
This situation is reported to dmesg:
[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up
Some users observed this problem on an Odroid HC2 with the JMS578
USB3-to-SATA bridge. The issue can be triggered by starting
a read-heavy workload on an attached SSD. After a while, the host
controller would die and the SSD would disappear from the system. [1]
Further analysis by Synopsys determined that controller revisions
other than the one in Odroid HC2 are also affected by this.
The recommended solution was to disable AutoRetry altogether.
This change does not have a noticeable performance impact. [2]
Revert the enablement commit. This will keep the AutoRetry bit in
the default state configured during SoC design [2].
Fixes: b138e23d3d ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1]
Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2]
Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3]
Cc: stable@vger.kernel.org
Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jakub Vanek <linuxtardis@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 609fded3f9 upstream.
The buffer address used in sysfs_emit should be aligned to PAGE_SIZE.
Use sysfs_emit_at instead to offset the buffer.
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b642dc982 upstream.
The pointers of each usb_power_delivery handles are stored in "pds"
array returned from the pd_get ops but not in the adjacent memory
calculated from "pd". Get the handles from "pds" array directly instead
of deriving them from "pd".
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b33ebb2415 upstream.
When calling device_add in the registration of typec_port, it will do
the NULL check on usb_power_delivery handle in typec_port for the
visibility of the device attributes. It is always NULL because port->pd
is set in typec_port_set_usb_power_delivery which is later than the
device_add call.
Set port->pd before device_add and only link the device after that.
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d245aedc00 upstream.
Sort the driver symbols alphabetically in order to make it more obvious
where new driver entries should be added.
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd92c8a1f9 upstream.
Add the device and product ID for this CAN bus interface / license
dongle. The device is usable either directly from user space or can be
attached to a kernel CAN interface with slcan_attach.
Reported-by: Kaufmann Automotive GmbH <info@kaufmann-automotive.ch>
Tested-by: Kaufmann Automotive GmbH <info@kaufmann-automotive.ch>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
[ johan: amend commit message and move entries in sort order ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4fc01af5b upstream.
The legacy gadget driver omitted calling usb_gadget_check_config()
to ensure that the USB device controller (UDC) has adequate resources,
including sufficient endpoint numbers and types, to support the given
configuration.
Previously, usb_add_config() was solely invoked by the legacy gadget
driver. Adds the necessary usb_gadget_check_config() after the bind()
operation to fix the issue.
Fixes: dce49449e0 ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230707230015.494999-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8291be6b5 upstream.
This reverts commit f08aa7c80d.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this driver, the bug means that probe cannot succeed when CONFIG_PM
is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: f08aa7c80d ("usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/ZKQoBa84U/ykEh3C@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b0328d0b upstream.
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support
gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1,
root hub speed will show on 10Gbps.
To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID
supported by xHCI to determine root hub speed. And add a quirk
XHCI_ZHAOXIN_HOST for this issue.
[fix warning about uninitialized symbol -Mathias]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-11-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a865a6522 upstream.
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance
improvement. However this TRB prefetch mechanism may cross page boundary,
which may access memory not allocated by xHCI driver. In order to fix
this issue, two pages was allocated for a segment and only the first
page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-10-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f927728186 upstream.
On ZHAOXIN ZX-100 project, xHCI can't work normally after resume
from system Sx state. To fix this issue, when resume from system
Sx state, reinitialize xHCI instead of restore.
So, Add XHCI_RESET_ON_RESUME quirk for ZX-100 to fix issue of
resuming from system Sx state.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-9-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7fbfd44c0 upstream.
power_supply_is_system_supplied() checks whether any power
supplies are present that aren't batteries to decide whether
the system is running on DC or AC. Downstream drivers use
this to make performance decisions.
Navi dGPUs include an UCSI function that has been exported
since commit 17631e8ca2 ("i2c: designware: Add driver
support for AMD NAVI GPU").
This UCSI function registers a power supply since commit
992a60ed0d ("usb: typec: ucsi: register with power_supply class")
but this is not a system power supply.
As the power supply for a dGPU is only for powering devices connected
to dGPU, create a device property to indicate that the UCSI endpoint
is only for the scope of `POWER_SUPPLY_SCOPE_DEVICE`.
Link: https://lore.kernel.org/lkml/20230516182541.5836-2-mario.limonciello@amd.com/
Reviewed-by: Evan Quan <evan.quan@amd.com>
Tested-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df49f2a0ac ]
This reverts commit edd60d24bd.
Heikki reports that this should not be a global flag just to work around
one broken driver and should be fixed differently, so revert it.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: edd60d24bd ("usb: common: usb-conn-gpio: Set last role to unknown before initial detection")
Link: https://lore.kernel.org/r/ZImE4L3YgABnCIsP@kuha.fi.intel.com
Cc: Prashanth K <quic_prashk@quicinc.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edd60d24bd ]
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() since last_role is same as
current role. This happens because during probe last_role gets
initialised to zero.
To avoid this, added a new constant in enum usb_role, last_role
is set to USB_ROLE_UNKNOWN before performing initial detection.
While at it, also handle default case for the usb_role switch
in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid
build warnings.
Fixes: 4602f3bff2 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a944da707 ]
If dwc3_qcom_create_urs_usb_platdev() fails, some resources still need to
be released, as already done in the other error handling path of the
probe.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <b69fa8dd68d816e7d24c88d3eda776ceb28c5dc5.1685890571.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fd95da2cf ]
In the probe, some resources are allocated with
dwc3_qcom_of_register_core() or dwc3_qcom_acpi_register_core(). The
corresponding resources are already coorectly freed in the error handling
path of the probe, but not in the remove function.
Fix it.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <c0215a84cdf18fb3514c81842783ec53cf149deb.1685891059.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e6bd945e6 ]
The declaration is in an #ifdef, which causes warnings when building
with 'make W=1' and without CONFIG_PM:
drivers/usb/core/devio.c:742:6: error: no previous prototype for 'usbfs_notify_suspend'
drivers/usb/core/devio.c:747:6: error: no previous prototype for 'usbfs_notify_resume'
Use the same #ifdef check around the function definitions to avoid
the warnings and slightly shrink the USB core.
Fixes: 7794f486ed ("usbfs: Add ioctls for runtime power management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230516202103.558301-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 342161c114 ]
Smatch reports:
drivers/usb/phy/phy-tahvo.c: tahvo_usb_probe()
warn: missing unwind goto?
After geting irq, if ret < 0, it will return without error handling to
free memory.
Just add error handling to fix this problem.
Fixes: 0d45a1373e ("usb: phy: tahvo: add IRQ check")
Signed-off-by: Li Yang <lidaxian@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230420140832.9110-1-lidaxian@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f6ecb89fe ]
Consider a case where gserial_disconnect has already cleared
gser->ioport. And if gserial_suspend gets called afterwards,
it will lead to accessing of gser->ioport and thus causing
null pointer dereference.
Avoid this by adding a null pointer check. Added a static
spinlock to prevent gser->ioport from becoming null after
the newly added null pointer check.
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1683278317-11774-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 097fb3ee71 ]
Function dwc3_qcom_probe() allocates memory for resource structure
which is pointed by parent_res pointer. This memory is not
freed. This leads to memory leak. Use stack memory to prevent
memory leak.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20230517172518.442591-1-VEfanov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada050c691 ]
dwc2_driver_probe() calls dwc2_lowlevel_hw_init() which deassert some reset
lines.
Should an error happen in dwc2_lowlevel_hw_init() after calling
reset_control_deassert() or in the probe after calling
dwc2_lowlevel_hw_init(), the reset lines remain deasserted.
Add some devm_add_action_or_reset() calls to re-assert the lines if needed.
Update the remove function accordingly.
This change is compile-tested only.
Fixes: 83f8da562f ("usb: dwc2: Add reset control to dwc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/c64537b5339342bd00f7c2152b8fc23792b9f95a.1683306479.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c024241d0 ]
Avoid extra 120ms delay during system resume.
The xHC controller may signal wake up to 120ms before showing which usb
device caused the wake on the xHC port registers.
The xhci driver therefore checks for port activity up to 120ms during
resume, making sure that the hub driver can see the port change, and
won't immediately runtime suspend back due to no port activity.
This is however only needed for runtime resume as system resume will
resume all child hubs and other child usb devices anyway.
Fixes: 253f588c70 ("xhci: Improve detection of device initiated wake signal.")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230428140056.1318981-3-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f7d552071 ]
Currently, the pci_resume method has only a flag indicating whether the
system is resuming from hibernation. In order to handle all PM events like
AUTO_RESUME (runtime resume from device in D3), RESUME (system resume from
s2idle, S3 or S4 states) etc change the pci_resume method to handle all PM
events.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230428140056.1318981-2-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 1c024241d0 ("xhci: Improve the XHCI system resume time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0285ab95 ]
The TUSB6010 (MUSB) device is picking up some GPIO lines
hardcoded by number and passing on to the TUSB6010 device
when registering it.
Instead of nasty workarounds, provide a GPIO descriptor
table and then make the TUSB6010 MUSB glue driver pick up
the GPIO lines directly, convert it to an IRQ and pass down
to the MUSB driver. OMAP2 is the only system using the
TUSB6010.
Stash the GPIO descriptors in the glue layer and use
then to power up and down the TUSB6010 on-demand, instead
of using boardfile callbacks.
Since the OMAP2 boards are the only boards using the
.set_power() and .board_set_power() callbacks, we can
just delete them as the power is now handled directly
in the TUSB6010 glue code.
Cc: Bin Liu <b-liu@ti.com>
Cc: linux-usb@vger.kernel.org
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
