[ Upstream commit 0a2b96e42a ]
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx6sx.dtsi#L1108-L1109
Fixes: 1e336aa0c0 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be18293e47 ]
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
mmc0: Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx7s.dtsi#L1216-L1217
Fixes: 1e336aa0c0 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9f5cd85f1 ]
Currently the dtbs_check generates warnings like this:
$nodename:0: 'dma-apbh@110000' does not match '^dma-controller(@.*)?$'
So fix all affected dma-apbh node names.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: be18293e47 ("ARM: dts: imx: Set default tuning step for imx7d usdhc")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 762b700982 ]
RTC interrupt level should be set to "LOW". This was revealed by the
introduction of commit:
f181987ef4 ("rtc: m41t80: use IRQ flags obtained from fwnode")
which changed the way IRQ type is obtained.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Stefan Riedmüller <s.riedmueller@phytec.de>
Fixes: 800d595151 ("ARM: dts: imx6: Add initial support for phyBOARD-Mira")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d14bd943f ]
Fix USB-related warnings in prtrvt, prtvt7, prti6q and prtwd2 device trees
by disabling unused usbphynop1 and usbphynop2 USB PHYs and providing proper
configuration for the over-current detection. This fixes the following
warnings with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over current polarity defined
By the way, fix over-current detection on usbotg port for prtvt7, prti6q
and prtwd2 boards. Only prtrvt do not have OC on USB OTG port.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c486762fb1 ]
The SK-IMX53 board, bearing i.MX536A CPU, is not stable when running at
1.2 GHz (default iMX53 maximum). The SoC is only rated up to 800 MHz.
Disable 1.2 GHz and 1 GHz frequencies.
Fixes: 0b8576d844 ("ARM: dts: imx: Add support for SK-iMX53 board")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ee31bb0524 upstream
check_bugs() is about to be phased out. Switch over to the new
arch_cpu_finalize_init() implementation.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613224545.078124882@linutronix.de
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8ef123393 upstream.
The DT version of this board has a custom file with the gpio
device. However, it does nothing because the d2net_init()
has no caller or prototype:
arch/arm/mach-orion5x/board-d2net.c:101:13: error: no previous prototype for 'd2net_init'
Call it from the board-dt file as intended.
Fixes: 94b0bd366e ("ARM: orion5x: convert d2net to Device Tree")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230516153109.514251-10-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edcbdd57de upstream.
After renaming NAND controller node name from "qpic-nand" to
"nand-controller", the board DTS/DTSI also have to be updated:
Warning (unit_address_vs_reg): /soc/qpic-nand@79b0000: node has a unit name, but no reg or ranges property
Cc: <stable@vger.kernel.org>
Fixes: 9e1e00f18a ("ARM: dts: qcom: Fix node name for NAND controller node")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230420072811.36947-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0f19091d4 upstream.
commit 04715461abf7 altered the node names in a DTSI file
used by qcom-apq8060-dragonboard.dts breaking the board.
Align the node names in the DTS file and the board boots
again.
Cc: stable@vger.kernel.org
Fixes: 85055a1eec ("ARM: dts: qcom-msm8660: align RPM regulators node name with bindings")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230414135747.34994-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fcb79ee3f0 ]
The pinctrl node was missing which change the pin mux to GPIO mode.
Add it so we don't have to rely on the bootloader to set the correct
mode.
Fixes: 79d83b3a45 ("ARM: dts: lan966x: add basic Kontron KSwitch D10 support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230616-feature-d10-dt-cleanups-v1-2-50dd0452b8fe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd274b733b ]
this typo was found by the dtbs_check
| ports:port@5:fixed-link: 'oneOf' conditional failed,
| {'speed': [[1000]], 'duplex-full': True} is not of type 'array'
| 'duplex-full' does not match any of the regexes: 'pinctrl-[0-]..."
this should have been full-duplex;
Fixes: 935327a735 ("ARM: dts: BCM5301X: Add DT for Meraki MR26")
Fixes: ec88a9c344 ("ARM: BCM5301X: Add DT for Meraki MR32")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/50522f45566951a9eabd22820647924cc6b4a264.1686238550.git.chunkeey@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f2778b1b ]
The audio routing flow is not correct, the flow should be from source
(second element in the pair) to sink (first element in the pair). The
flow now is from "HP_OUT" to "Playback", where "Playback" is source
and "HP_OUT" is sink, i.e. the direction is swapped and there is no
direct link between the two either.
Fill in the correct routing, where "HP_OUT" supplies the "Headphone Jack",
"Line In Jack" supplies "LINE_IN" input, "Microphone Jack" supplies "MIC_IN"
input and "Mic Bias" supplies "Microphone Jack".
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0501fdec10 ]
make dtbs_check:
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
PWM specifiers referring to R-Car PWM Timer Controllers should contain
only two cells.
Fix this by dropping the bogus third cell.
Fixes: 6f89dd9e93 ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e5c3167424a43faf8c1fa68d9667b3d87dc86d8.1684855911.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98b503c7fb ]
On Meson8 uart_B and uart_C do not work, because they are relying on
incorrect clocks. Change the references of pclk to the correct CLKID
(UART1 for uart_B and UART2 for uart_C), to allow use of the two uarts.
This was originally reported by Hans-Frieder Vogt for Meson8b [0], but
the same bug is also present in meson8.dtsi
[0] https://lore.kernel.org/linux-amlogic/trinity-bf20bcb9-790b-4ab9-99e3-0831ef8257f4-1680878185420@3c-app-gmx-bap55/
Fixes: 57007bfb54 ("ARM: dts: meson8: Fix the UART device-tree schema validation")
Reported-by: Hans-Frieder Vogt <hfdevel@gmx.net> # for meson8b.dtsi
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230516203029.1031174-1-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e60c230588 ]
Add the qcom,controlled-remotely property for the blsp2_bam
controller node. This board requires this, otherwise the board stalls
during the boot for some reason (most probably because TZ mishandles the
protection error and keeps on looping somewhere inside).
Fixes: 62bc817922 dts: msm8974: Add blsp2_bam dma node
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-3-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cf765e598 ]
Fix the following error in kernel log due to too long sound card name:
"
asoc-audio-graph-card sound: ASoC: driver name too long 'STM32MP1-AV96-HDMI' -> 'STM32MP1-AV96-H'
"
Fixes: e027da3427 ("ARM: dts: stm32: Add bindings for audio on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861bc1d288 ]
omap2 contains a hack to define tick_broadcast() on non-SMP
configurations in place of the normal SMP definition. This one
causes a warning because of a missing prototype:
arch/arm/mach-omap2/board-generic.c:44:6: error: no previous prototype for 'tick_broadcast'
Make sure to always include the header with the declaration.
Fixes: d86ad463d6 ("ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs")
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20230516153109.514251-9-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419013740e ]
ep93xx_clocksource_read() is only called from the file it is declared in,
while ep93xx_timer_init() is declared in a header that is not included here.
arch/arm/mach-ep93xx/timer-ep93xx.c:120:13: error: no previous prototype for 'ep93xx_timer_init'
arch/arm/mach-ep93xx/timer-ep93xx.c:63:5: error: no previous prototype for 'ep93xx_clocksource_read'
Fixes: 000bc17817 ("ARM: ep93xx: switch to GENERIC_CLOCKEVENTS")
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230516153109.514251-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0285ab95 ]
The TUSB6010 (MUSB) device is picking up some GPIO lines
hardcoded by number and passing on to the TUSB6010 device
when registering it.
Instead of nasty workarounds, provide a GPIO descriptor
table and then make the TUSB6010 MUSB glue driver pick up
the GPIO lines directly, convert it to an IRQ and pass down
to the MUSB driver. OMAP2 is the only system using the
TUSB6010.
Stash the GPIO descriptors in the glue layer and use
then to power up and down the TUSB6010 on-demand, instead
of using boardfile callbacks.
Since the OMAP2 boards are the only boards using the
.set_power() and .board_set_power() callbacks, we can
just delete them as the power is now handled directly
in the TUSB6010 glue code.
Cc: Bin Liu <b-liu@ti.com>
Cc: linux-usb@vger.kernel.org
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 078dc5194c ]
The OMAP2 platform data quirk is using the global GPIO numberspace
to obtain two WLAN GPIOs to drive power and xcvr reset GPIO
lines during start-up.
Rewrite the quirk to use a GPIO descriptor table so we avoid using
global GPIO numbers.
This gets rid of the final dependency on the legacy <linux/gpio.h>
header from the OMAP2/3 platforms.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94075d16be ]
This switches the USB hub GPIO reset line handling in the
OMAP2 pdata quirks over to using GPIO descriptors to avoid using
the global GPIO numberspace.
Since the GPIOs are exported and assumedly used by some kind
of userspace we cannot simply use hogs in the device tree.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5f4fa60d6 ]
The TWL4030 GPIO driver has a custom platform data .set_up()
callback to call back into the platform and do misc stuff such
as hog and export a GPIO for WLAN PWR on a specific OMAP3 board.
Avoid all the kludgery in the platform data and the boardfile
and just put the quirks right into the driver. Make it
conditional on OMAP3.
I think the exported GPIO is used by some kind of userspace
so ordinary DTS hogs will probably not work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c729baa860 ]
After fixing all the offending users referencing the global GPIO
numberspace in OMAP1, a few sites still remain including the
legacy <linus/gpio.h> header for no reason.
Delete the last remaining users, and OMAP1 is free from legacy
GPIO dependencies.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df89de979f ]
The code in serial.c looks up GPIOs corresponding to a line
on the UART when muxed in as GPIO to use this as a wakeup
on serial activity for OMAP1.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, set as input and convert to IRQ numbers,
then set these to wakeup IRQs. This is ugly but should work.
This is only needed on the OSK1 and Nokia 770 devices that
use the OMAP16xx.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 084b6f2167 ]
The platform devices on the Nokia 770 is using some
board-specific IRQs that get statically assigned to platform
devices in the boardfile.
This does not work with dynamic IRQ chip bases.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e519f0bb64 ]
A recent change to the OMAP driver making it use a dynamic GPIO
base created problems with some old OMAP1 board files, among
them Nokia 770, SX1 and also the OMAP2 Nokia n8x0.
Fix up all instances of GPIOs being used for the MMC driver
by pushing the handling of power, slot selection and MMC
"cover" into the driver as optional GPIOs.
This is maybe not the most perfect solution as the MMC
framework have some central handlers for some of the
stuff, but it at least makes the situtation better and
solves the immediate issue.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 767d83361a ]
The Nokia 770 is using GPIOs from the global numberspace on the
CBUS node to pass down to the LCD controller. This regresses when we
let the OMAP GPIO driver use dynamic GPIO base.
The Nokia 770 now has dynamic allocation of IRQ numbers, so this
needs to be fixed for it to work.
As this is the only user of LCD MIPID we can easily augment the
driver to use a GPIO descriptor instead and resolve the issue.
The platform data .shutdown() callback wasn't even used in the
code, but we encode a shutdown asserting RESET in the remove()
callback for completeness sake.
The CBUS also has the ADS7846 touchscreen attached.
Populate the devices on the Nokia 770 CBUS I2C using software
nodes instead of platform data quirks. This includes the LCD
and the ADS7846 touchscreen so the conversion just brings the LCD
along with it as software nodes is an all-or-nothing design
pattern.
The ADS7846 has some limited support for using GPIO descriptors,
let's convert it over completely to using device properties and then
fix all remaining boardfile users to provide all platform data using
software nodes.
Dump the of includes and of_match_ptr() in the ADS7846 driver as part
of the job.
Since we have to move ADS7846 over to obtaining the GPIOs it is
using exclusively from descriptors, we provide descriptor tables
for the two remaining in-kernel boardfiles using ADS7846:
- PXA Spitz
- MIPS Alchemy DB1000 development board
It was too hard for me to include software node conversion of
these two remaining users at this time: the spitz is using a
hscync callback in the platform data that would require further
GPIO descriptor conversion of the Spitz, and moving the hsync
callback down into the driver: it will just become too big of
a job, but it can be done separately.
The MIPS Alchemy DB1000 is simply something I cannot test, so take
the easier approach of just providing some GPIO descriptors in
this case as I don't want the patch to grow too intrusive.
As we see that several device trees have incorrect polarity flags
and just expect to bypass the gpiolib polarity handling, fix up
all device trees too, in a separate patch.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 480c82daa3 ]
It appears this happens because the OMAP driver now
allocates GPIO numbers dynamically, so all that is
references by number is a bit up in the air.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c40db6249 ]
It appears this happens because the OMAP driver now
allocates GPIO numbers dynamically, so all that is
references by number is a bit up in the air.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa1ae0cd89 ]
The AMS Delta board uses GPIO descriptors exclusively and
does not have any dependencies on the legacy <linux/gpio.h>
header, so just drop it.
Acked-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c32c81f3db ]
Aaro reports problems on the OSK1 board after we altered
the dynamic base for GPIO allocations.
It appears this happens because the OMAP driver now
allocates GPIO numbers dynamically, so all that is
references by number is a bit up in the air.
Let's bite the bullet and try to just move the gpio_chip
in the tps65010 MFD driver over to using dynamic allocations.
Alter everything in the OSK1 board file to use a GPIO
descriptor table and lookups.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
The .setup() callback for tps65010 was used for some GPIO
hogging, but since the OSK1 is the only user in the entire
kernel we can alter the signatures to something that
is helpful and make a clean transition.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: andy.shevchenko@gmail.com
Cc: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ffec92e70 ]
The model property should be at the top level, let's move it out
of the pinctrl node.
Fixes: d2eaf949d2 ("ARM: dts: omap3-gta04a5one: define GTA04A5 variant with OneNAND")
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9660efc2af ]
The ethernet MAC EEPROM is not populated on the SoM itself, it has to be
populated on each carrier board. Move the EEPROM into the correct place
in DTs, i.e. the carrier board DTs. Add label to the EEPROM too.
Fixes: 7e76f82acd ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d542ce8d47 ]
With the current device tree for meson8b, uarts B (e.g. available on pins
8/10 on Odroid-C1) and C (pins 3/5 on Odroid-C1) do not work, because they
are relying on incorrect clocks. Change the references of pclk to the
correct CLKID, to allow use of the two uarts.
Fixes: 3375aa7713 ("ARM: dts: meson8b: Fix the UART device-tree schema validation")
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/trinity-bf20bcb9-790b-4ab9-99e3-0831ef8257f4-1680878185420@3c-app-gmx-bap55
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c8e2c575 ]
There is no such property in the SPI controller binding documentation.
Also Linux driver doesn't look for it.
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: spi@18029200: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230503122830.3200-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dda5f312bb ]
The sync_*() ops on arch/arm are defined in terms of the regular bitops
with no special handling. This is not correct, as UP kernels elide
barriers for the fully-ordered operations, and so the required ordering
is lost when such UP kernels are run under a hypervsior on an SMP
system.
Fix this by defining sync ops with the required barriers.
Note: On 32-bit arm, the sync_*() ops are currently only used by Xen,
which requires ARMv7, but the semantics can be implemented for ARMv6+.
Fixes: e54d2f6152 ("xen/arm: sync_bitops")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230605070124.3741859-2-mark.rutland@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9c3ddcec ]
checker_stack_use_t32strd() and kprobe_handler() can be made static since
they are not used from other files, while coverage_start_registers()
and __kprobes_test_case() are used from assembler code, and just need
a declaration to avoid a warning with the global definition.
arch/arm/probes/kprobes/checkers-common.c:43:18: error: no previous prototype for 'checker_stack_use_t32strd'
arch/arm/probes/kprobes/core.c:236:16: error: no previous prototype for 'kprobe_handler'
arch/arm/probes/kprobes/test-core.c:723:10: error: no previous prototype for 'coverage_start_registers'
arch/arm/probes/kprobes/test-core.c:918:14: error: no previous prototype for '__kprobes_test_case_start'
arch/arm/probes/kprobes/test-core.c:952:14: error: no previous prototype for '__kprobes_test_case_end_16'
arch/arm/probes/kprobes/test-core.c:967:14: error: no previous prototype for '__kprobes_test_case_end_32'
Fixes: 6624cf651f ("ARM: kprobes: collects stack consumption for store instructions")
Fixes: 454f3e132d ("ARM/kprobes: Remove jprobe arm implementation")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8b35ca3e45 upstream.
arm has an additional check for address < FIRST_USER_ADDRESS before
expanding the stack. Since FIRST_USER_ADDRESS is defined everywhere
(generally as 0), move that check to the generic expand_downwards().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
* Fix GICv2 emulation on GICv3 after the locking rework
* Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why
Generic:
* Avoid setting page table entries pointing to a deleted memslot if a
host page table entry is changed concurrently with the deletion.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmSUoQoUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroP6swf5ATU/csLrT1gR5v+YkXmlUUUi4423
VceijG7Y2+XSH7dk9svf1WLLi4OTvxs4WfUEEnFPmEXMx9PkL+btaACcXfVjpolA
dD6RsPk6fZ8XOpVkjuWENFJtstm9jOUQIZeEShvIKRabHRFHAPlmYF6LJ67S/j+E
iK/8ScnAHznbsGlN+HhLhwpLxzkam09ZwpXt9eT1ZNev7E8FAnYI9nGGxz6UIqAW
WHWJIyMpYpXZYsNuHXDMUAvn1TCpkKM0i38NEll0qEUktI9pW3cmm3kOSAlVe+47
V3LMtAP0v2VC938VAPsXBZgDlVr7yfEqzb73VBGd9776QDK3b6rjF1ZDYA==
=fuod
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why
Generic:
- Avoid setting page table entries pointing to a deleted memslot if a
host page table entry is changed concurrently with the deletion"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Avoid illegal stage2 mapping on invalid memory slot
KVM: arm64: Use raw_smp_processor_id() in kvm_pmu_probe_armpmu()
KVM: arm64: Restore GICv2-on-GICv3 functionality
KVM: arm64: PMU: Don't overwrite PMUSERENR with vcpu loaded
KVM: arm64: PMU: Restore the host's PMUSERENR_EL0
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why...
-----BEGIN PGP SIGNATURE-----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=JwZ/
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-6.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.4, take #4
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why...
Several device tree files get the polarity of the pendown-gpios
wrong: this signal is active low. Fix up all incorrect flags, so
that operating systems can rely on the flag being correctly set.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230510105156.1134320-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
