[ Upstream commit 3bfbff9b46 ]
The bootrom burned into the MT7986 SoC will try multiple locations on
the SPI-NAND flash to load bl2 in case the bl2 image located at the the
previously attempted offset is corrupt.
Use 0x100000 instead of 0x80000 as partition size for bl2 on SPI-NAND,
allowing for up to four redundant copies of bl2 (typically sized a
bit less than 0x40000).
Fixes: 8e01fb15b8 ("arm64: dts: mt7986: add Bananapi R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZH9UGF99RgzrHZ88@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4366b5695 ]
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A76) cluster at a maximum of 2200MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculated the mean result for each cluster
4. Calculated DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scaled results to 1024:
result_c0 = dmips_mhz_c0 / dmips_mhz_c1 * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 12016411 Dhry/s
Cluster 1 (BIG): 31702034 Dhry/s
The calculated scaled results are:
Cluster 0: 426.953226899238 (rounded to 427)
Cluster 1: 1024
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230602183515.3778780-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38c6ced4e ]
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: 635fb18ba0 ("arch: arm64: dts: Add support for AM69 Starter Kit")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c10a9df30e ]
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: e20a06aca5 ("arm64: dts: ti: Add support for J784S4 EVM board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155e7635ed ]
Mailbox nodes are now disabled by default. The BeagleBoard AI64 DT
addition went in at around the same time and must have missed that
change so the mailboxes are not re-enabled. Do that here.
Fixes: fae14a1cb8 ("arm64: dts: ti: Add k3-j721e-beagleboneai64")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11a1397bbf ]
The USB HC node is missing the interconnect paths, so add them.
Fixes: 7f7e5c1b03 ("arm64: dts: qcom: sm8550: Add USB PHYs and controller nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230601103817.4066446-1-abel.vesa@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 223ce29c8b ]
The framebuffer configuration for edo pdx203, written in edo dtsi (which
is overwritten in pdx206 dts for its smaller panel) has to use a
1096x2560 configuration as this is what the panel (and framebuffer area)
has been initialized to. Downstream userspace also has access to (and
uses) this 2.5k mode by default, and only switches the panel to 4k when
requested.
This is similar to commit be8de06dc3 ("arm64: dts: qcom:
sm8150-kumano: Panel framebuffer is 2.5k instead of 4k") which fixed the
same for the previous generation Sony platform.
Fixes: 69cdb97ef6 ("arm64: dts: qcom: sm8250: Add support for SONY Xperia 1 II / 5 II (Edo platform)")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230606211418.587676-1-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b2c7ac8e4 ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: ffc50b2d38 ("arm64: dts: qcom: Add base SM8550 dtsi")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-8-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91e83140b5 ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: c83545d953 ("arm64: dts: sdm845: Add rpmh-rsc node")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-6-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b04cbd81b ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: 07c8ded6e3 ("arm64: dts: qcom: add sdm670 and pixel 3a device trees")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-5-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab033e7846 ]
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
Without this, only AMC votes are being commited.
Fixes: 6bd20c54b5 ("arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-rsc-v1-3-b4a985f57b8b@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a325956fa7 ]
The realtek Bluetooth module uses the same driver as the
realtek,rtl8822cs-bt and the realtek,rtl8723bs-bt, however by selecting
the 8723bs advanced power saving features are disabled that appear
to interfere with normal operation of the bluetooth module. This
change switches the compatible string to disable power saving. Without
this patch evtest of a paired bluetooth controller fails, with this
patch the controller operates as expected.
Fixes: b6986b7920 ("arm64: dts: rockchip: Update compatible for bluetooth")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20230508160811.3568213-3-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28ee08cef4 ]
The I2S0_8CH_MCLKOUT clock rate on Rock 5B board defaults to 12 MHz and
it is used to provide the master clock (MCLK) for the ES8316 audio
codec.
On sound card initialization, this limits the allowed sample rates
according to the MCLK/LRCK ratios supported by the codec, which results
in the following non-standard rates: 15625, 30000, 31250, 46875.
Hence, the very first access of the sound card fails:
Broken configuration for playback: no configurations available: Invalid argument
Setting of hwparams failed: Invalid argument
However, all subsequent attempts will succeed, as the audio graph card
will request a correct clock frequency, based on the stream sample rate
and the multiplication factor.
Assign MCLK to 12.288 MHz, which allows the codec to advertise most of
the standard sample rates.
Fixes: 55529fe3f3 ("arm64: dts: rockchip: Add rk3588-rock-5b analog audio")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-4-cristian.ciocaltea@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a2c4e5635 ]
The schematics are misleading, the flow control is for HSCIF1. We need
SCIF1 for GNSS/GPS which does not use flow control.
Fixes: c6c816e22b ("arm64: dts: ulcb-kf: enable SCIF1")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230525084823.4195-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea6c5f21ef ]
Firmware shipped on mt8195 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: 5eb2e303ec ("arm64: dts: mediatek: Introduce MT8195 Cherry platform's Tomato")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.5.Ia0b6ebbaa351e3cd67e201355b9ae67783c7d718@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d72cfbd6fc ]
Firmware shipped on mt8192 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: 331fae2fc9 ("arm64: dts: mediatek: Introduce MT8192-based Asurada board family")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.4.Ie7e600278ffbed55a1e5a58178203787b1449b35@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42127f578e ]
Firmware shipped on mt8183 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.3.I525a2ed4260046d43c885ee1275e91707743df1c@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83022f6484 ]
This file is using definitions from the spmi-vadc header, so we need to
include it.
Fixes: 11975b9b81 ("arm64: dts: qcom: Add pm7250b PMIC")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-pm7250b-sid-v1-1-fc648478cc25@fairphone.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5500f823db ]
The 96Boards specification expects a 1.8V power rail on the low-speed
expansion connector that is able to provide at least 0.18W / 100 mA.
According to the DB410c hardware user manual this is done by connecting
both L15 and L16 in parallel with up to 55mA each (for 110 mA total) [1].
Unfortunately the current regulator setup in the DB410c device tree
does not implement the specification correctly and only provides 5 mA:
- Only L15 is marked always-on, so L16 is never enabled.
- Without specifying a load the regulator is put into LPM where
it can only provide 5 mA.
Fix this by:
- Adding proper voltage constraints for L16.
- Making L16 always-on.
- Adding regulator-system-load for both L15 and L16. 100 mA should be
available in total, so specify 50 mA for each. (The regulator
hardware can only be in normal (55 mA) or low-power mode (5 mA) so
this will actually result in the expected 110 mA total...)
[1]: https://www.96boards.org/documentation/consumer/dragonboard/dragonboard410c/hardware-docs/hardware-user-manual.md.html#power-supplies
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 828dd5d66f ("arm64: dts: apq8016-sbc: make 1.8v available on LS expansion")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-2-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e27654df20 ]
For some reason DB410c has completely bogus regulator constraints that
actually just correspond to the programmable voltages which are already
provided by the regulator driver. Some of them are not just outside the
recommended operating conditions of the APQ8016E SoC but even exceed
the absolute maximum ratings, potentially risking permanent device
damage.
In practice it's not quite as dangerous thanks to the RPM firmware:
It turns out that it has its own voltage constraints and silently
clamps all regulator requests. For example, requesting 3.3V for L5
(allowed by the current regulator constraints!) still results in 1.8V
being programmed in the actual regulator hardware.
Experimentation with various voltages shows that the internal RPM
voltage constraints roughly correspond to the safe "specified range"
in the PM8916 Device Specification (rather than the "programmable
range" used inside apq8016-sbc.dtsi right now).
Combine those together with some fixed voltages used in the old
msm-3.10 device tree from Qualcomm to give DB410c some actually valid
voltage constraints.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 4c7d53d16d ("arm64: dts: apq8016-sbc: add regulators support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a0156b886 ]
Add missing reg property to touchscreen child node to fix dtbs W=1 warnings:
Warning (unit_address_vs_reg): /soc@0/geniqup@ac0000/i2c@a98000/touchscreen@20/rmi4-f12@12: node has a unit name, but no reg or ranges property
Fixes: be497abe19 ("arm64: dts: qcom: Add support for Xiaomi Mi Mix2s")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Molly Sophia <mollysophia379@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230419211856.79332-18-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9ef7a805a ]
Unlike typical GIC interrupts, first cell for SPMI interrupts is the
USID rather than GIC_SPI/GIC_PPI/GIC_LPI qualifier. Fix the resin
interrupt to use USID value 0x0 rather than GIC_SPI define.
Fixes: f86ae6f23a ("arm64: dts: qcom: sagit: add initial device tree for sagit")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230409182145.122895-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14e6c47b62 ]
Card-Detect (CD) gpio for SDHC2 is an active GPIO line. Fix the same.
This allows the uSD card to be properly detected on the board.
Fixes: 8d58a8c0d9 ("arm64: dts: qcom: Add base qrb4210-rb2 board dts")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516075908.2323372-3-bhupesh.sharma@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fb4576269 ]
Update the size of GICC and GICV regions to 8kB as the GICC_DIR & GICV_DIR
registers lie in the second 4kB region. Also, add target CPU encoding.
Fixes: 97cb36ff52 ("arm64: dts: qcom: Add ipq9574 SoC and AL02 board support")
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230425084010.15581-2-quic_devipriy@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70be83708c ]
PSCI is not implemented on SparX-5 at all, there is no ATF and U-boot that
is shipped does not implement it as well.
I have tried flashing the latest BSP 2022.12 U-boot which did not work.
After contacting Microchip, they confirmed that there is no ATF for the
SoC nor PSCI implementation which is unfortunate in 2023.
So, disable PSCI as otherwise kernel crashes as soon as it tries probing
PSCI with, and the crash is only visible if earlycon is used.
Since PSCI is not implemented, switch core bringup to use spin-tables
which are implemented in the vendor U-boot and actually work.
Tested on PCB134 with eMMC (VSC5640EV).
Fixes: 6694aee00a ("arm64: dts: sparx5: Add basic cpu support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20230221105039.316819-1-robert.marko@sartura.hr
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Changes related to cache management for DMA memory caused WiFi to stop
work on SC7180 and SC7280 based products, using TF-A. These changes
marks the relevant device dma-coherent to correct the behavior.
-----BEGIN PGP SIGNATURE-----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=ZdjH
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmSV/OcACgkQYKtH/8kJ
UidD+Q//XxciqeCyOqnK+Uv2MXj3CDswUPZIQ3bTi8/JJt6WpT6qP8ZYWP3CbfeX
qTe3tgbjmG+5Co2cUq1PSwNTLn1/vG2mEyhz48EDOmh+20joeduKRwt5DrN29+GP
nk/N+1bslHpEmjgfSIliOLJNLlMvBpUOyFKTT70zDkRN1o3en/aLKhI1N5h1G8IF
f3wt68siitFKNEBgLyN6VTZeEO0LWuX4oqC5ggq8hA+0k3XuGRHcp4OXQvTbhrF8
AgRQSaaWc9awBSO0kVbOG+P3cXTc2KdJIua6uaq5ToJ6LPArQ3jtIDfMMMWBQtWd
4evU2maitV384SpqlQ1PN8TC5oqIEVdvfh/bujDPO5iTajj9x8LT9u0suPkU7q0A
tpF9zwpcClo7K1svgEi3wJ7vr/Ktm8mxhu+OKmYeQfQCIyAIGD+00UCVuHbSUuzo
doptwvUNQzJ3i6Ifszdl5fslnN/ol5gP02PdUsQiXwC3NIAtWjTgtENYq4WN0VwV
REQzIhHRlXF2NO+UBmAvL/Ju9+7yV3fYkdFBTjJ85BnIDejnZbaZ4ErRYTxzuNYA
/VGiSuE5aVpTBuLPLF2pAmUnFsITXMTKEv/knObq4BM0YiWgixee0PFmCPWVvUOd
P7tDO9TUFHjcFJGHge+nRgiMRzedVqIW2d4SfPFWAF5KgiVwH74=
=f/SB
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-fixes-for-6.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
One last Qualcomm ARM64 DeviceTree fix for v6.4
Changes related to cache management for DMA memory caused WiFi to stop
work on SC7180 and SC7280 based products, using TF-A. These changes
marks the relevant device dma-coherent to correct the behavior.
* tag 'qcom-arm64-fixes-for-6.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sc7280: Mark SCM as dma-coherent for chrome devices
arm64: dts: qcom: sc7180: Mark SCM as dma-coherent for trogdor
arm64: dts: qcom: sc7180: Mark SCM as dma-coherent for IDP
dt-bindings: firmware: qcom,scm: Document that SCM can be dma-coherent
Link: https://lore.kernel.org/r/20230622203248.106422-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Just like for sc7180 devices using the Chrome bootflow (AKA trogdor
and IDP), sc7280 devices using the Chrome bootflow also need their
firmware marked dma-coherent. On sc7280 this wasn't causing WiFi to
fail to startup, since WiFi works differently there. However, on
sc7280 devices we were still getting the message at bootup after
commit 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache
invalidation from arch_dma_prep_coherent()"""):
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 9c900000.memory: assign memory failed
qcom_rmtfs_mem: probe of 9c900000.memory failed with error -22
We should mark SCM properly just like we did for trogdor.
Fixes: 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: 7a1f4e7f74 ("arm64: dts: qcom: sc7280: Add basic dts/dtsi files for sc7280 soc")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.4.I21dc14a63327bf81c6bb58fe8ed91dbdc9849ee2@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Trogdor devices use firmware backed by TF-A instead of Qualcomm's
normal TZ. On TF-A we end up mapping memory as cacheable.
Specifically, you can see in Trogdor's TF-A code [1] in
qti_sip_mem_assign() that we call qti_mmap_add_dynamic_region() with
MT_RO_DATA. This translates down to MT_MEMORY instead of
MT_NON_CACHEABLE or MT_DEVICE. Apparently Qualcomm's normal TZ
implementation maps the memory as non-cacheable.
Let's add the "dma-coherent" attribute to the SCM for trogdor.
Adding "dma-coherent" like this fixes WiFi on sc7180-trogdor
devices. WiFi was broken as of commit 7bd6680b47 ("Revert "Revert
"arm64: dma: Drop cache invalidation from
arch_dma_prep_coherent()"""). Specifically at bootup we'd get:
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 94600000.memory: assign memory failed
qcom_rmtfs_mem: probe of 94600000.memory failed with error -22
From discussion on the mailing lists [2] and over IRC [3], it was
determined that we should always have been tagging the SCM as
dma-coherent on trogdor but that the old "invalidate" happened to make
things work most of the time. Tagging it properly like this is a much
more robust solution.
[1] https://chromium.googlesource.com/chromiumos/third_party/arm-trusted-firmware/+/refs/heads/firmware-trogdor-13577.B/plat/qti/common/src/qti_syscall.c
[2] https://lore.kernel.org/r/20230614165904.1.I279773c37e2c1ed8fbb622ca6d1397aea0023526@changeid
[3] https://oftc.irclog.whitequark.org/linux-msm/2023-06-15
Fixes: 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.3.Ic62daa649b47b656b313551d646c4de9a7da4bd4@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
sc7180-idp is, for most intents and purposes, a trogdor device.
Specifically, sc7180-idp is designed to run the same style of firmware
as trogdor devices. This can be seen from the fact that IDP has the
same "Reserved memory changes" in its device tree that trogdor has.
Recently it was realized that we need to mark SCM as dma-coherent to
match what trogdor's style of firmware (based on TF-A) does [1]. That
means we need this dma-coherent tag on IDP as well.
Without this, on newer versions of Linux, specifically those with
commit 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache
invalidation from arch_dma_prep_coherent()"""), WiFi will fail to
work. At bootup you'll see:
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 94600000.memory: assign memory failed
qcom_rmtfs_mem: probe of 94600000.memory failed with error -22
[1] https://lore.kernel.org/r/20230615145253.1.Ic62daa649b47b656b313551d646c4de9a7da4bd4@changeid
Fixes: 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: f5ab220d16 ("arm64: dts: qcom: sc7180: Add remoteproc enablers")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.2.I3c17d546d553378aa8a0c68c3fe04bccea7cba17@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
