[ Upstream commit a372d66af4 ]
incl_srcpt has the limitation, mentioned in commit b4638af888 ("net:
dsa: sja1105: always enable the INCL_SRCPT option"), that frames with a
MAC DA of 01:80:c2:xx:yy:zz will be received as 01:80:c2:00:00:zz unless
PTP RX timestamping is enabled.
The incl_srcpt option was initially unconditionally enabled, then that
changed with commit 42824463d3 ("net: dsa: sja1105: Limit use of
incl_srcpt to bridge+vlan mode"), then again with b4638af888 ("net:
dsa: sja1105: always enable the INCL_SRCPT option"). Bottom line is that
it now needs to be always enabled, otherwise the driver does not have a
reliable source of information regarding source_port and switch_id for
link-local traffic (tag_8021q VLANs may be imprecise since now they
identify an entire bridging domain when ports are not standalone).
If we accept that PTP RX timestamping (and therefore, meta frame
generation) is always enabled in hardware, then that limitation could be
avoided and packets with any MAC DA can be properly received, because
meta frames do contain the original bytes from the MAC DA of their
associated link-local packet.
This change enables meta frame generation unconditionally, which also
has the nice side effects of simplifying the switch control path
(a switch reset is no longer required on hwtstamping settings change)
and the tagger data path (it no longer needs to be informed whether to
expect meta frames or not - it always does).
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf62c8177 ]
Switch in MAXLEN register stores the maximum size of a data frame.
The MTU size is 18 bytes smaller than the frame size.
The current settings are causing problems with packet forwarding.
This patch fixes the MTU settings to proper values.
Fixes: fb77ffc6ec ("net: dsa: vsc73xx: make the MTU configurable")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230628194327.1765644-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4638af888 ]
Link-local traffic on bridged SJA1105 ports is sometimes tagged by the
hardware with source port information (when the port is under a VLAN
aware bridge).
The tag_8021q source port identification has become more loose
("imprecise") and will report a plausible rather than exact bridge port,
when under a bridge (be it VLAN-aware or VLAN-unaware). But link-local
traffic always needs to know the precise source port.
Modify the driver logic (and therefore: the tagging protocol itself) to
always include the source port information with link-local packets,
regardless of whether the port is standalone, under a VLAN-aware or
VLAN-unaware bridge. This makes it possible for the tagging driver to
give priority to that information over the tag_8021q VLAN header.
The big drawback with INCL_SRCPT is that it makes it impossible to
distinguish between an original MAC DA of 01:80:C2:XX:YY:ZZ and
01:80:C2:AA:BB:ZZ, because the tagger just patches MAC DA bytes 3 and 4
with zeroes. Only if PTP RX timestamping is enabled, the switch will
generate a META follow-up frame containing the RX timestamp and the
original bytes 3 and 4 of the MAC DA. Those will be used to patch up the
original packet. Nonetheless, in the absence of PTP RX timestamping, we
have to live with this limitation, since it is more important to have
the more precise source port information for link-local traffic.
Fixes: d7f9787a76 ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID")
Fixes: 91495f21fc ("net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2edcfcbb3c ]
The driver implements a workaround for the fact that it doesn't have an
IRQ source to tell it whether PTP frames are available through the
extraction registers, for those frames to be processed and passed
towards the network stack. That workaround is to configure the switch,
through felix_hwtstamp_set() -> felix_update_trapping_destinations(),
to create two copies of PTP packets: one sent over Ethernet to the DSA
master, and one to be consumed through the aforementioned CPU extraction
queue registers.
The reason why we want PTP packets to be consumed through the CPU
extraction registers in the first place is because we want to see their
hardware RX timestamp. With tag_8021q, that is only visible that way,
and it isn't visible with the copy of the packet that's transmitted over
Ethernet.
The problem with the workaround implementation is that it drops the
packet received over Ethernet, in expectation of its copy being present
in the CPU extraction registers. However, if felix_hwtstamp_set() hasn't
run (aka PTP RX timestamping is disabled), the driver will drop the
original PTP frame and there will be no copy of it in the CPU extraction
registers. So, the network stack will simply not see any PTP frame.
Look at the port's trapping configuration to see whether the driver has
previously enabled the CPU extraction registers. If it hasn't, just
don't RX timestamp the frame and let it be passed up the stack by DSA,
which is perfectly fine.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the introduction of the OF bindings, DSA has always had a policy that
in case multiple CPU ports are present in the device tree, the numerically
smallest one is always chosen.
The MT7530 switch family, except the switch on the MT7988 SoC, has 2 CPU
ports, 5 and 6, where port 6 is preferable on the MT7531BE switch because
it has higher bandwidth.
The MT7530 driver developers had 3 options:
- to modify DSA when the MT7531 switch support was introduced, such as to
prefer the better port
- to declare both CPU ports in device trees as CPU ports, and live with the
sub-optimal performance resulting from not preferring the better port
- to declare just port 6 in the device tree as a CPU port
Of course they chose the path of least resistance (3rd option), kicking the
can down the road. The hardware description in the device tree is supposed
to be stable - developers are not supposed to adopt the strategy of
piecemeal hardware description, where the device tree is updated in
lockstep with the features that the kernel currently supports.
Now, as a result of the fact that they did that, any attempts to modify the
device tree and describe both CPU ports as CPU ports would make DSA change
its default selection from port 6 to 5, effectively resulting in a
performance degradation visible to users with the MT7531BE switch as can be
seen below.
Without preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 374 MBytes 157 Mbits/sec 734 sender
[ 5][TX-C] 0.00-20.00 sec 373 MBytes 156 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 778 Mbits/sec 0 sender
[ 7][RX-C] 0.00-20.00 sec 1.81 GBytes 777 Mbits/sec receiver
With preferring port 6:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 856 Mbits/sec 273 sender
[ 5][TX-C] 0.00-20.00 sec 1.99 GBytes 855 Mbits/sec receiver
[ 7][RX-C] 0.00-20.00 sec 1.72 GBytes 737 Mbits/sec 15 sender
[ 7][RX-C] 0.00-20.00 sec 1.71 GBytes 736 Mbits/sec receiver
Using one port for WAN and the other ports for LAN is a very popular use
case which is what this test emulates.
As such, this change proposes that we retroactively modify stable kernels
(which don't support the modification of the CPU port assignments, so as to
let user space fix the problem and restore the throughput) to keep the
mt7530 driver preferring port 6 even with device trees where the hardware
is more fully described.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLDP frames are link-local frames, therefore they must be trapped to the
CPU port. Currently, the MT753X switches treat LLDP frames as regular
multicast frames, therefore flooding them to user ports. To fix this, set
LLDP frames to be trapped to the CPU port(s).
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPDUs are link-local frames, therefore they must be trapped to the CPU
port. Currently, the MT7530 switch treats BPDUs as regular multicast
frames, therefore flooding them to user ports. To fix this, set BPDUs to be
trapped to the CPU port. Group this on mt7530_setup() and
mt7531_setup_common() into mt753x_trap_frames() and call that.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All MT7530 switch IP variants share the MT7530_MFC register, but the
current driver only writes it for the switch variant that is integrated in
the MT7621 SoC. Modify the code to include all MT7530 derivatives.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7531_CPU_PMAP represents the destination port mask for trapped-to-CPU
frames (further restricted by PCR_MATRIX).
Currently the driver sets the first CPU port as the single port in this bit
mask, which works fine regardless of whether the device tree defines port
5, 6 or 5+6 as CPU ports. This is because the logic coincides with DSA's
logic of picking the first CPU port as the CPU port that all user ports are
affine to, by default.
An upcoming change would like to influence DSA's selection of the default
CPU port to no longer be the first one, and in that case, this logic needs
adaptation.
Since there is no observed leakage or duplication of frames if all CPU
ports are defined in this bit mask, simply include them all.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DEV_MAC_MAXLEN_CFG register contains a 16-bit value - up to 65535.
Plus 2 * VLAN_HLEN (4), that is up to 65543.
The picos_per_byte variable is the largest when "speed" is lowest -
SPEED_10 = 10. In that case it is (1000000L * 8) / 10 = 800000.
Their product - 52434400000 - exceeds 32 bits, which is a problem,
because apparently, a multiplication between two 32-bit factors is
evaluated as 32-bit before being assigned to a 64-bit variable.
In fact it's a problem for any MTU value larger than 5368.
Cast one of the factors of the multiplication to u64 to force the
multiplication to take place on 64 bits.
Issue found by Coverity.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230613170907.2413559-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Without LED triggers, the driver now fails to build:
drivers/net/dsa/qca/qca8k-leds.c: In function 'qca8k_parse_port_leds':
drivers/net/dsa/qca/qca8k-leds.c:403:31: error: 'struct led_classdev' has no member named 'hw_control_is_supported'
403 | port_led->cdev.hw_control_is_supported = qca8k_cled_hw_control_is_supported;
| ^
There is a mix of 'depends on' and 'select' for LEDS_TRIGGERS, so it's
not clear what we should use here, but in general using 'depends on'
causes fewer problems, so use that.
Fixes: e0256648c8 ("net: dsa: qca8k: implement hw_control ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN9303 doesn't associate FDB (ALR) entries with VLANs, it has just one
global Address Logic Resolution table [1].
Ignore VID in port_fdb_{add|del} methods, go on with the global table. This
is the same semantics as hellcreek or RZ/N1 implement.
Visible symptoms:
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to delete 00:xx:xx:xx:xx:cf vid 1 from fdb: -2
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to add 00:xx:xx:xx:xx:cf vid 1 to fdb: -95
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/00002308A.pdf
Fixes: 0620427ea0 ("net: dsa: lan9303: Add fdb/mdb manipulation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230531143826.477267-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de4 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU
port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports
are enabled, port 6 becomes the only port to forward the frames to. But
port 5 is the active port, so no frames received from the user ports will
be forwarded to port 5 which breaks network connectivity.
Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix
this issue by setting the bit that corresponds to the CPU port without
overwriting the other bits.
Clear the bits beforehand only for the MT7531 switch. According to the
documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference
Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and
UNU_FFP bits are set to 1 for MT7531, 0 for MT7530.
The commit 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user
ports") silently changed the method to set the bits on the MT7530_MFC.
Instead of clearing the relevant bits before mt7530_cpu_port_enable()
which runs under a for loop, the commit started doing it on
mt7530_cpu_port_enable().
Back then, this didn't really matter as only a single CPU port could be
used since the CPU port number was hardcoded. The driver was later changed
with commit 1f9a6abecf ("net: dsa: mt7530: get cpu-port via dp->cpu_dp
instead of constant") to retrieve the CPU port via dp->cpu_dp. With that,
this silent change became an issue for when using multiple CPU ports.
Fixes: 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user ports")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: 81d24bbce7/u-boot-mt/drivers/net/rt2880_eth.c (L2195)
Fixes: 7ef6f6f8d2 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rsvd2cpu capability for mv88e6321 model, to allow proper bpdu
processing.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Fixes: 51c901a775 ("net: dsa: mv88e6xxx: distinguish Global 2 Rsvd2CPU")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With LEDS_CLASS=m, a built-in qca8k driver fails to link:
arm-linux-gnueabi-ld: drivers/net/dsa/qca/qca8k-leds.o: in function `qca8k_setup_led_ctrl':
qca8k-leds.c:(.text+0x1ea): undefined reference to `devm_led_classdev_register_ext'
Change the dependency to avoid the broken configuration.
Fixes: 1e264f9d29 ("net: dsa: qca8k: add LEDs basic support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230420213639.2243388-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two variants of the MT7531 switch IC which got different
features (and pins) regarding port 5:
* MT7531AE: SGMII/1000Base-X/2500Base-X SerDes PCS
* MT7531BE: RGMII
Moving the creation of the SerDes PCS from mt753x_setup to mt7530_probe
with commit 6de2852297 ("net: dsa: mt7530: move SGMII PCS creation
to mt7530_probe function") works fine for MT7531AE which got two
instances of mtk-pcs-lynxi, however, MT7531BE requires mt7531_pll_setup
to setup clocks before the single PCS on port 6 (usually used as CPU
port) starts to work and hence the PCS creation failed on MT7531BE.
Fix this by introducing a pointer to mt7531_create_sgmii function in
struct mt7530_priv and call it again at the end of mt753x_setup like it
was before commit 6de2852297 ("net: dsa: mt7530: move SGMII PCS
creation to mt7530_probe function").
Fixes: 6de2852297 ("net: dsa: mt7530: move SGMII PCS creation to mt7530_probe function")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/ZDvlLhhqheobUvOK@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because of the logic in place, SW_HUGE_PACKET can never be set.
(If the first condition is true, then the 2nd one is also true, but is not
executed)
Change the logic and update each bit individually.
Fixes: 29d1e85f45 ("net: dsa: microchip: ksz8: add MTU configuration support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/43107d9e8b5b8b05f0cbd4e1f47a2bb88c8747b2.1681755535.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).
There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mqprio queue configuration can appear either through
TC_SETUP_QDISC_MQPRIO or through TC_SETUP_QDISC_TAPRIO. Make sure both
are treated in the same way.
Code does nothing new for now (except for rejecting multiple TXQs per
TC, which is a useless concept with DSA switches).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This doesn't apply anything to hardware and in general doesn't do
anything that the software variant doesn't do, except for checking that
there isn't more than 1 TXQ per TC (TXQs for a DSA switch are a dubious
concept anyway). The reason we add this is to be able to parse one more
field added to struct tc_mqprio_qopt_offload, namely preemptible_tcs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the switch emits an IRQ, we don't know what caused it, and we
iterate through all ports to check the MAC Merge status.
Move that iteration inside the ocelot lib; we will change the locking in
a future change and it would be good to encapsulate that lock completely
within the ocelot lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
That comment was written prior to knowing that what I was actually
seeing was a manifestation of the bug fixed in commit b4024c9e5c
("felix: Fix initialization of ioremap resources").
There isn't any particular reason now why the hardware initialization is
done in felix_setup(), so just delete that comment to avoid spreading
misinformation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch can either take the MAC or the PHY role in an MII or RMII
link. There are distinct PHY_INTERFACE_ macros for these two roles.
Correct the mapping so that the `REV` version is used for the PHY
role.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230411023541.2372609-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To handle potential read/write operation failures, update
ksz8_w_sta_mac_table() to make use of the return values provided by
read/write functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since ksz8_w_sta_mac_table() is only used within ksz8795.c, make it static
to limit its scope.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Take advantage of the return values provided by read/write functions in
ksz8_r_sta_mac_table() to handle cases where read/write operations may
fail.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Prepare for the next patch by ensuring that ksz8_r_sta_mac_table() does
not use error codes for empty entries. This change will enable better
handling of read/write errors in the upcoming patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As ksz8_r_sta_mac_table() is only used within ksz8795.c, there is no need
to export it. Make the function static for better encapsulation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for add/del_fdb operations and utilize the refactored static
MAC table code. This resolves kernel warnings caused by the lack of fdb
add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move static MAC table operations to separate functions in order to reuse
the code for add/del_fdb. This is needed to address kernel warnings
caused by the lack of fdb add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add driver for the built-in Gigabit Ethernet switch which can be found
in the MediaTek MT7988 SoC.
The switch shares most of its design with MT7530 and MT7531, but has
it's registers mapped into the SoCs register space rather than being
connected externally or internally via MDIO.
Introduce a new platform driver to support that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As MT7530 and MT7531 internally use 32-bit wide registers, each access
to any register of the switch requires several operations on the MDIO
bus. Hence if there is congruent access, e.g. due to PCS or PHY
polling, this can mess up and interfere with another ongoing register
access sequence.
However, the MDIO bus mutex is only relevant for MDIO-connected
switches. Prepare switches which have there registers directly mapped
into the SoCs register space via MMIO which do not require such
locking. There we can simply use regmap's default locking mechanism.
Hence guard mutex operations to only be performed in case of MDIO
connected switches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split MT7530 switch driver into a common part and a part specific
for MDIO connected switches and multi-chip modules.
Move MDIO-specific functions to newly introduced mt7530-mdio.c while
keeping the common parts in mt7530.c.
Introduce new Kconfig symbol CONFIG_NET_DSA_MT7530_MDIO which is
implied by CONFIG_NET_DSA_MT7530.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7988 shares a significant part of the setup function with MT7531.
Split-off those parts into a shared function which is going to be used
also by mt7988_setup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move commonly used parts from mt7530_remove into new
mt7530_remove_common helper function which will be used by both,
mt7530_remove and the to-be-introduced mt7988_remove.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move commonly used parts from mt7530_probe into new mt7530_probe_common
helper function which will be used by both, mt7530_probe and the
to-be-introduced mt7988_probe.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of splitting mt7530.c into a driver for MDIO-connected
as well as MDIO-accessed built-in switches on one hand and MMIO-accessed
built-in switches move the p5_inft_modes() function from mt7530.h to
mt7530.c. The function is only needed there and will trigger a compiler
warning about a defined but unused function otherwise when including
mt7530.h in the to-be-introduced bus-specific drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the MDIO bus lock only needs to be involved if actually operating
on an MDIO-connected switch we will need to skip locking for built-in
switches which are accessed via MMIO.
Create helper functions which simplify that upcoming change.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move creating the SGMII PCS from mt753x_setup() to the more appropriate
mt7530_probe() function.
This is done also in preparation of moving all functions related to
MDIO-connected MT753x switches to a separate module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
