[ Upstream commit 69ddba9d17 ]
Currently, the MT753X switches treat frames with :01-0D and :0F MAC DAs as
regular multicast frames, therefore flooding them to user ports.
On page 205, section "8.6.3 Frame filtering" of the active standard, IEEE
Std 802.1Q™-2022, it is stated that frames with 01:80:C2:00:00:00-0F as MAC
DA must only be propagated to C-VLAN and MAC Bridge components. That means
VLAN-aware and VLAN-unaware bridges. On the switch designs with CPU ports,
these frames are supposed to be processed by the CPU (software). So we make
the switch only forward them to the CPU port. And if received from a CPU
port, forward to a single port. The software is responsible of making the
switch conform to the latter by setting a single port as destination port
on the special tag.
This switch intellectual property cannot conform to this part of the
standard fully. Whilst the REV_UN frame tag covers the remaining :04-0D and
:0F MAC DAs, it also includes :22-FF which the scope of propagation is not
supposed to be restricted for these MAC DAs.
Set frames with :01-03 MAC DAs to be trapped to the CPU port(s). Add a
comment for the remaining MAC DAs.
Note that the ingress port must have a PVID assigned to it for the switch
to forward untagged frames. A PVID is set by default on VLAN-aware and
VLAN-unaware ports. However, when the network interface that pertains to
the ingress port is attached to a vlan_filtering enabled bridge, the user
can remove the PVID assignment from it which would prevent the link-local
frames from being trapped to the CPU port. I am yet to see a way to forward
link-local frames while preventing other untagged frames from being
forwarded too.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8bf353577 ]
Whether VLAN-aware or not, on every VID VLAN table entry that has the CPU
port as a member of it, frames are set to egress the CPU port with the VLAN
tag stacked. This is so that VLAN tags can be appended after hardware
special tag (called DSA tag in the context of Linux drivers).
For user ports on a VLAN-unaware bridge, frame ingressing the user port
egresses CPU port with only the special tag.
For user ports on a VLAN-aware bridge, frame ingressing the user port
egresses CPU port with the special tag and the VLAN tag.
This causes issues with link-local frames, specifically BPDUs, because the
software expects to receive them VLAN-untagged.
There are two options to make link-local frames egress untagged. Setting
CONSISTENT or UNTAGGED on the EG_TAG bits on the relevant register.
CONSISTENT means frames egress exactly as they ingress. That means
egressing with the VLAN tag they had at ingress or egressing untagged if
they ingressed untagged. Although link-local frames are not supposed to be
transmitted VLAN-tagged, if they are done so, when egressing through a CPU
port, the special tag field will be broken.
BPDU egresses CPU port with VLAN tag egressing stacked, received on
software:
00:01:25.104821 AF Unknown (382365846), length 106:
| STAG | | VLAN |
0x0000: 0000 6c27 614d 4143 0001 0000 8100 0001 ..l'aMAC........
0x0010: 0026 4242 0300 0000 0000 0000 6c27 614d .&BB........l'aM
0x0020: 4143 0000 0000 0000 6c27 614d 4143 0000 AC......l'aMAC..
0x0030: 0000 1400 0200 0f00 0000 0000 0000 0000 ................
BPDU egresses CPU port with VLAN tag egressing untagged, received on
software:
00:23:56.628708 AF Unknown (25215488), length 64:
| STAG |
0x0000: 0000 6c27 614d 4143 0001 0000 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
BPDU egresses CPU port with VLAN tag egressing tagged, received on
software:
00:01:34.311963 AF Unknown (25215488), length 64:
| Mess |
0x0000: 0000 6c27 614d 4143 0001 0001 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
To prevent confusing the software, force the frame to egress UNTAGGED
instead of CONSISTENT. This way, frames can't possibly be received TAGGED
by software which would have the special tag field broken.
VLAN Tag Egress Procedure
For all frames, one of these options set the earliest in this order will
apply to the frame:
- EG_TAG in certain registers for certain frames.
This will apply to frame with matching MAC DA or EtherType.
- EG_TAG in the address table.
This will apply to frame at its incoming port.
- EG_TAG in the PVC register.
This will apply to frame at its incoming port.
- EG_CON and [EG_TAG per port] in the VLAN table.
This will apply to frame at its outgoing port.
- EG_TAG in the PCR register.
This will apply to frame at its outgoing port.
EG_TAG in certain registers for certain frames:
PPPoE Discovery_ARP/RARP: PPP_EG_TAG and ARP_EG_TAG in the APC register.
IGMP_MLD: IGMP_EG_TAG and MLD_EG_TAG in the IMC register.
BPDU and PAE: BPDU_EG_TAG and PAE_EG_TAG in the BPC register.
REV_01 and REV_02: R01_EG_TAG and R02_EG_TAG in the RGAC1 register.
REV_03 and REV_0E: R03_EG_TAG and R0E_EG_TAG in the RGAC2 register.
REV_10 and REV_20: R10_EG_TAG and R20_EG_TAG in the RGAC3 register.
REV_21 and REV_UN: R21_EG_TAG and RUN_EG_TAG in the RGAC4 register.
With this change, it can be observed that a bridge interface with stp_state
and vlan_filtering enabled will properly block ports now.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50e60de381 ]
For PF to AF interrupt vector and VF to AF vector same
interrupt handler is registered which is causing race condition.
When two interrupts are raised to two CPUs at same time
then two cores serve same event corrupting the data.
Fixes: 7304ac4567 ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfcf6355f5 ]
When PF sending link status messages to VF, it is possible
that by the time link_event_task work function is executed
VF might have brought down. Hence before sending VF link
status message check whether VF is up to receive it.
Fixes: ad513ed938 ("octeontx2-vf: Link event notification support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7558ce0d97 ]
Only one execution context for the workqueue used for PF and
VFs mailbox communication is incorrect since multiple works are
queued simultaneously by all the VFs and PF link UP messages.
Hence use default number of execution contexts by passing zero
as max_active to alloc_workqueue function. With this fix in place,
modify UP messages also to wait until completion.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf2f24939 ]
During VF driver remove, a message is sent to detach VF
resources to PF but VF is not waiting until message is
complete. Also mailbox interrupts need to be turned off
after the detach resource message is complete. This patch
fixes that problem.
Fixes: 05fcc9e089 ("octeontx2-pf: Attach NIX and NPA block LFs")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a88e0f936b ]
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9dae ("octeontx2-pf: Mailbox communication with AF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d27e2da94a ]
Fix race condition leading to system crash during EEH error handling
During EEH error recovery, the bnx2x driver's transmit timeout logic
could cause a race condition when handling reset tasks. The
bnx2x_tx_timeout() schedules reset tasks via bnx2x_sp_rtnl_task(),
which ultimately leads to bnx2x_nic_unload(). In bnx2x_nic_unload()
SGEs are freed using bnx2x_free_rx_sge_range(). However, this could
overlap with the EEH driver's attempt to reset the device using
bnx2x_io_slot_reset(), which also tries to free SGEs. This race
condition can result in system crashes due to accessing freed memory
locations in bnx2x_free_rx_sge()
799 static inline void bnx2x_free_rx_sge(struct bnx2x *bp,
800 struct bnx2x_fastpath *fp, u16 index)
801 {
802 struct sw_rx_page *sw_buf = &fp->rx_page_ring[index];
803 struct page *page = sw_buf->page;
....
where sw_buf was set to NULL after the call to dma_unmap_page()
by the preceding thread.
EEH: Beginning: 'slot_reset'
PCI 0011:01:00.0#10000: EEH: Invoking bnx2x->slot_reset()
bnx2x: [bnx2x_io_slot_reset:14228(eth1)]IO slot reset initializing...
bnx2x 0011:01:00.0: enabling device (0140 -> 0142)
bnx2x: [bnx2x_io_slot_reset:14244(eth1)]IO slot reset --> driver unload
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0080000025065fc
Oops: Kernel access of bad area, sig: 11 [#1]
.....
Call Trace:
[c000000003c67a20] [c00800000250658c] bnx2x_io_slot_reset+0x204/0x610 [bnx2x] (unreliable)
[c000000003c67af0] [c0000000000518a8] eeh_report_reset+0xb8/0xf0
[c000000003c67b60] [c000000000052130] eeh_pe_report+0x180/0x550
[c000000003c67c70] [c00000000005318c] eeh_handle_normal_event+0x84c/0xa60
[c000000003c67d50] [c000000000053a84] eeh_event_handler+0xf4/0x170
[c000000003c67da0] [c000000000194c58] kthread+0x1c8/0x1d0
[c000000003c67e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
To solve this issue, we need to verify page pool allocations before
freeing.
Fixes: 4cace675d6 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240315205535.1321-1-thinhtr@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32fa4366cc ]
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec7329517 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f490c492e9 ]
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 0 Reserved
0 1 20MHz
1 0 40MHz
1 1 25MHz
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] [3] [5]
: : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
_____________________________
ESW_P3_LED_0 |__________________________
: : : :
: : [4]...:
: :
[2]................:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] [2-1] [3] [5]
: : : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
___________________ _______
ESW_P3_LED_0 |_________| |__________________
: : : : :
: [2-2]...: [4]...:
[2]................:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
ESW_P3_LED_0 low period before reset deassertion:
5000 usec
- 5100 usec
TEST RESET HOLD
# (usec)
---------------------
1 5410
2 5440
3 4375
4 5490
5 5475
6 4335
7 4370
8 5435
9 4205
10 4335
11 3750
12 3170
13 4395
14 4375
15 3515
16 4335
17 4220
18 4175
19 4175
20 4350
Min 3170
Max 5490
Median 4342.500
Avg 4466.500
Revert commit 2920dd92b9 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7db7775ea ]
Commit d3256efd8e ("veth: allow enabling NAPI even without XDP") tried to fix
the fact that GRO was not possible without XDP, because veth did not use NAPI
without XDP. However, it also introduced the behaviour that GRO is always
enabled, when XDP is enabled.
While it might be desired for most cases, it is confusing for the user at best
as the GRO flag suddenly changes, when an XDP program is attached. It also
introduces some complexities in state management as was partially addressed in
commit fe9f801355 ("net: veth: clear GRO when clearing XDP even when down").
But the biggest problem is that it is not possible to disable GRO at all, when
an XDP program is attached, which might be needed for some use cases.
Fix this by not touching the GRO flag on XDP enable/disable as the code already
supports switching to NAPI if either GRO or XDP is requested.
Link: https://lore.kernel.org/lkml/20240311124015.38106-1-ignat@cloudflare.com/
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Fixes: fe9f801355 ("net: veth: clear GRO when clearing XDP even when down")
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea80e3ed09 ]
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/b40da332dfe763932a82f9f62a4709457a15dd6c
Fixes: ba37b7caf1 ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1b85ef15a ]
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e30cef001d ]
txgbe register clk which name is i2c_designware.pci_dev_id(),
clk_name will be stored in clk_lookup_alloc. If PCIe bus number
is larger than 0x39, clk_name size will be larger than 20 bytes.
It exceeds clk_lookup_alloc MAX_DEV_ID limits. So the driver
shortened clk_name.
Fixes: b63f20485e ("net: txgbe: Register fixed rate clock")
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20240313080634.459523-1-duanqiangwen@net-swift.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e642921dfe ]
Use wake_up API instead of wake_up_interruptible, since
wait_event_timeout API is used for waiting on command completion.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84e95149bd ]
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again.
Fixes: bb9a8d0311 ("nfp: flower: monitor and offload LAG groups")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20240308142540.9674-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8a5c731fd ]
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292 ("net: phy: DP83822: Add setting the fixed internal delay")
Signed-off-by: Tim Pambor <tp@osasysteme.de>
Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d80f79dd ]
Currently, the mac port is fixed to configured as full dplex mode in
hclge_mac_init() when driver initialization or reset restore. Users may
change the mode to half duplex with ethtool, so it may cause the user
configuration dropped after reset.
To fix it, don't change the duplex mode when resetting.
Fixes: 2d03eacc0b ("net: hns3: Only update mac configuation when necessary")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07a1d6dc90 ]
In hns3_dcbnl_ieee_delapp, should check ieee_delapp not ieee_setapp.
This path fix the wrong judgment.
Fixes: 0ba22bcb22 ("net: hns3: add support config dscp map to tc")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4469c0c5b1 ]
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec91 ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07161b2416 ]
Add check for usbnet_get_endpoints() and return the error if it fails
in order to transfer the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 19a38d8e0a ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support")
Link: https://lore.kernel.org/r/20240305075927.261284-1-nichen@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 257310e998 ]
Simplify stats accumulation logic to fix the case where we don't take
previous stat value into account, we should always respect it.
Main netdev stats of our PF (Tx/Rx packets/bytes) were reported orders of
magnitude too big during OpenStack reconfiguration events, possibly other
reconfiguration cases too.
The regression was reported to be between 6.1 and 6.2, so I was almost
certain that on of the two "preserve stats over reset" commits were the
culprit. While reading the code, it was found that in some cases we will
increase the stats by arbitrarily large number (thanks to ignoring "-prev"
part of condition, after zeroing it).
Note that this fixes also the case where we were around limits of u64, but
that was not the regression reported.
Full disclosure: I remember suggesting this particular piece of code to
Ben a few years ago, so blame on me.
Fixes: 2fd5e433cd ("ice: Accumulate HW and Netdev statistics over reset")
Reported-by: Nebojsa Stevanovic <nebojsa.stevanovic@gcore.com>
Link: https://lore.kernel.org/intel-wired-lan/VI1PR02MB439744DEDAA7B59B9A2833FE912EA@VI1PR02MB4397.eurprd02.prod.outlook.com
Reported-by: Christian Rohmann <christian.rohmann@inovex.de>
Link: https://lore.kernel.org/intel-wired-lan/f38a6ca4-af05-48b1-a3e6-17ef2054e525@inovex.de
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee14cc9ea1 ]
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b4 ("igb: enable internal PPS for the i210")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 244ae992e3 ]
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The IGC_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read IGC_TSIRC into 'tsicr';
2. handle the interrupts present in 'tsirc' and mark them in 'ack';
3. write 'ack' into IGC_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de> # Intel i225
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4152222e0 ]
The kzalloc() in brcmf_pmksa_v3_op() will return null if the
physical memory has run out. As a result, if we dereference
the null value, the null pointer dereference bug will happen.
Return -ENOMEM from brcmf_pmksa_v3_op() if kzalloc() fails
for pmk_op.
Fixes: a96202acae ("wifi: brcmfmac: cfg80211: Add support for PMKID_V3 operations")
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229103153.18533-1-duoming@zju.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c238adbc57 ]
total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just
ofdm_fa_cnt.
Fixes: 960361238b ("rtw88: 8821c: add false alarm statistics")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f3cb6d17-e4e4-44a7-9c9b-72aed994b5c9@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1dfa21427 ]
Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because
of frequent disconnections:
Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
This is caused by a mistake in the chip initialisation. This version of
the chip requires loading an extra AGC table right after the main one,
but the extra table is being loaded at the wrong time, in
rtw_chip_board_info_setup().
Move the extra AGC table loading to the right place, in
rtw_phy_load_tables().
The rtw_chip_board_info_setup() can only do "software" things, and
rtw_phy_load_tables() can really do IO.
Fixes: 5d6651fe85 ("rtw88: 8821c: support RFE type2 wifi NIC")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/276c31d8-b9a8-4e54-a3ac-09b74657aff7@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41a7acb7dd ]
RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after
reading and writing certain addresses.
Without this, the firmware upload fails approximately more than 50% of
the time.
Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU
but without Bluetooth.
Fixes: a82dfd33d1 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f12ed39d-28e8-4b8b-8d22-447bcf295afc@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07ce1d4637 ]
In some case, the MTCL table will exist, but MTDS table will not.
So the SAR will init fail. This patch make MTCL and MTDS can exist
with no dependence.
Fixes: f965333e49 ("mt76: mt7921: introduce ACPI SAR support")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c957280ef6 ]
From commit a304e1b828 ("[PATCH] Debug shared irqs"), there is a test
to make sure the shared irq handler should be able to handle the unexpected
event after deregistration. For this case, let's apply MT76_REMOVED flag to
indicate the device was removed and do not run into the resource access
anymore.
BUG: KASAN: use-after-free in mt7921_irq_handler+0xd8/0x100 [mt7921e]
Read of size 8 at addr ffff88824a7d3b78 by task rmmod/11115
CPU: 28 PID: 11115 Comm: rmmod Tainted: G W L 5.17.0 #10
Hardware name: Micro-Star International Co., Ltd. MS-7D73/MPG B650I
EDGE WIFI (MS-7D73), BIOS 1.81 01/05/2024
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x1f/0x190
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
kasan_report.cold+0x7f/0x11b
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
mt7921_irq_handler+0xd8/0x100 [mt7921e]
free_irq+0x627/0xaa0
devm_free_irq+0x94/0xd0
? devm_request_any_context_irq+0x160/0x160
? kobject_put+0x18d/0x4a0
mt7921_pci_remove+0x153/0x190 [mt7921e]
pci_device_remove+0xa2/0x1d0
__device_release_driver+0x346/0x6e0
driver_detach+0x1ef/0x2c0
bus_remove_driver+0xe7/0x2d0
? __check_object_size+0x57/0x310
pci_unregister_driver+0x26/0x250
__do_sys_delete_module+0x307/0x510
? free_module+0x6a0/0x6a0
? fpregs_assert_state_consistent+0x4b/0xb0
? rcu_read_lock_sched_held+0x10/0x70
? syscall_enter_from_user_mode+0x20/0x70
? trace_hardirqs_on+0x1c/0x130
do_syscall_64+0x5c/0x80
? trace_hardirqs_on_prepare+0x72/0x160
? do_syscall_64+0x68/0x80
? trace_hardirqs_on_prepare+0x72/0x160
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/CABXGCsOdvVwdLmSsC8TZ1jF0UOg_F_W3wqLECWX620PUkvNk=A@mail.gmail.com/
Fixes: 9270270d62 ("wifi: mt76: mt7921: fix PCI DMA hang after reboot")
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de88827751 ]
Sync the value of HIF_TXD_V2_1 with firmware to let it correctly fill
TXD values for HW path.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3ad99be7c ]
The efuse data starts from the 48th bytes instead of 64th bytes in the
returned event skb.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d52c97592f ]
The EHT MCS map subfield of 20 MHz-Only is not present in the EHT
capability of AP, so STA does not need to parse the subfield.
Moreover, AP should parse the subfield only if STA is 20 MHz-Only, which
can be confirmed by checking supported channel width in HE capability.
Fixes: 92aa2da9fa ("wifi: mt76: mt7996: enable EHT support in firmware")
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c832c228f ]
This patch fixes the following TWT issues:
- Change table_mask to u16 to support up to 16 TWT stations
- Reject TWT flows for duplicated establishment
- Fix possible unaligned pointer
- Remove unsupported TWT_CONTROL_WAKE_DUR_UNIT flag
- The minimum TWT duration supported by mt7996 chipsets is 64. Reply
with TWT_SETUP_CMD_DICTATE if the min_twt_dur is smaller than 64
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3ec643947 ]
This reverts commit fcf690b0b4.
When using a wilc1000 chip over a spi bus, users can optionally define a
reset gpio and a chip enable gpio. The reset line of wilc1000 is active
low, so to hold the chip in reset, a low (physical) value must be applied.
The corresponding device tree binding documentation was introduced by
commit f31ee3c0a5 ("wilc1000: Document enable-gpios and reset-gpios
properties") and correctly indicates that the reset line is an active-low
signal. The corresponding driver part, brought by commit ec031ac479
("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the
correct logic. But commit fcf690b0b4 ("wifi: wilc1000: use correct
sequence of RESET for chip Power-UP/Down") eventually flipped this logic
and started misusing the gpiod APIs, applying an inverted logic when
powering up/down the chip (for example, setting the reset line to a logic
"1" during power up, which in fact asserts the reset line when device tree
describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any
platform currently using the driver in SPI mode must use a faulty reset
line description in device tree, or else chip will be maintained in reset
and will not even allow to bring up the chip.
Fix reset line usage by inverting back the gpiod APIs usage, setting the
reset line to the logic value "0" when powering the chip, and the logic
value "1" when powering off the chip.
Fixes: fcf690b0b4 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240217-wilc_1000_reset_line-v2-1-b216f433d7d5@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e886ba2b ]
Avoid the following warnings by removing the ena_select_queue() function
and rely on the net core to do the queue selection, The issue happen
when an skb received from an interface with more queues than ena is
forwarded to the ena interface.
[ 1176.159959] eth0 selects TX queue 11, but real number of TX queues is 8
[ 1176.863976] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1180.767877] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1188.703742] eth0 selects TX queue 14, but real number of TX queues is 8
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Kamal Heib <kheib@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1ea6db35f ]
An old cleanup went a little too far and causes a warning with clang-16
and higher as it breaks control flow integrity (KCFI) rules:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy_shim.c:64:34: error: cast from 'void (*)(struct brcms_phy *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
64 | brcms_init_timer(physhim->wl, (void (*)(void *))fn,
| ^~~~~~~~~~~~~~~~~~~~
Change this one instance back to passing a void pointer so it can be
used with the timer callback interface.
Fixes: d89a4c8060 ("staging: brcm80211: removed void * from softmac phy")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240213100548.457854-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb5942b77c ]
wilc_netdev_cleanup currently triggers a KASAN warning, which can be
observed on interface registration error path, or simply by
removing the module/unbinding device from driver:
echo spi0.1 > /sys/bus/spi/drivers/wilc1000_spi/unbind
==================================================================
BUG: KASAN: slab-use-after-free in wilc_netdev_cleanup+0x508/0x5cc
Read of size 4 at addr c54d1ce8 by task sh/86
CPU: 0 PID: 86 Comm: sh Not tainted 6.8.0-rc1+ #117
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from print_report+0x154/0x500
print_report from kasan_report+0xac/0xd8
kasan_report from wilc_netdev_cleanup+0x508/0x5cc
wilc_netdev_cleanup from wilc_bus_remove+0xc8/0xec
wilc_bus_remove from spi_remove+0x8c/0xac
spi_remove from device_release_driver_internal+0x434/0x5f8
device_release_driver_internal from unbind_store+0xbc/0x108
unbind_store from kernfs_fop_write_iter+0x398/0x584
kernfs_fop_write_iter from vfs_write+0x728/0xf88
vfs_write from ksys_write+0x110/0x1e4
ksys_write from ret_fast_syscall+0x0/0x1c
[...]
Allocated by task 1:
kasan_save_track+0x30/0x5c
__kasan_kmalloc+0x8c/0x94
__kmalloc_node+0x1cc/0x3e4
kvmalloc_node+0x48/0x180
alloc_netdev_mqs+0x68/0x11dc
alloc_etherdev_mqs+0x28/0x34
wilc_netdev_ifc_init+0x34/0x8ec
wilc_cfg80211_init+0x690/0x910
wilc_bus_probe+0xe0/0x4a0
spi_probe+0x158/0x1b0
really_probe+0x270/0xdf4
__driver_probe_device+0x1dc/0x580
driver_probe_device+0x60/0x140
__driver_attach+0x228/0x5d4
bus_for_each_dev+0x13c/0x1a8
bus_add_driver+0x2a0/0x608
driver_register+0x24c/0x578
do_one_initcall+0x180/0x310
kernel_init_freeable+0x424/0x484
kernel_init+0x20/0x148
ret_from_fork+0x14/0x28
Freed by task 86:
kasan_save_track+0x30/0x5c
kasan_save_free_info+0x38/0x58
__kasan_slab_free+0xe4/0x140
kfree+0xb0/0x238
device_release+0xc0/0x2a8
kobject_put+0x1d4/0x46c
netdev_run_todo+0x8fc/0x11d0
wilc_netdev_cleanup+0x1e4/0x5cc
wilc_bus_remove+0xc8/0xec
spi_remove+0x8c/0xac
device_release_driver_internal+0x434/0x5f8
unbind_store+0xbc/0x108
kernfs_fop_write_iter+0x398/0x584
vfs_write+0x728/0xf88
ksys_write+0x110/0x1e4
ret_fast_syscall+0x0/0x1c
[...]
David Mosberger-Tan initial investigation [1] showed that this
use-after-free is due to netdevice unregistration during vif list
traversal. When unregistering a net device, since the needs_free_netdev has
been set to true during registration, the netdevice object is also freed,
and as a consequence, the corresponding vif object too, since it is
attached to it as private netdevice data. The next occurrence of the loop
then tries to access freed vif pointer to the list to move forward in the
list.
Fix this use-after-free thanks to two mechanisms:
- navigate in the list with list_for_each_entry_safe, which allows to
safely modify the list as we go through each element. For each element,
remove it from the list with list_del_rcu
- make sure to wait for RCU grace period end after each vif removal to make
sure it is safe to free the corresponding vif too (through
unregister_netdev)
Since we are in a RCU "modifier" path (not a "reader" path), and because
such path is expected not to be concurrent to any other modifier (we are
using the vif_mutex lock), we do not need to use RCU list API, that's why
we can benefit from list_for_each_entry_safe.
[1] https://lore.kernel.org/linux-wireless/ab077dbe58b1ea5de0a3b2ca21f275a07af967d2.camel@egauge.net/
Fixes: 8399918f30 ("staging: wilc1000: use RCU list to maintain vif interfaces list")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240212-wilc_rework_deinit-v1-1-9203ae56c27f@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cdb86487e ]
One of the flags was from the wrong API.
Fixes: 9be162a7b6 ("wifi: iwlwifi: mvm: add support for the new MAC CTXT command")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240208185302.a338c30ec4e9.Ic2813cdeba4443c692d462fc4859392f069d7e33@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a163c57610 ]
Interrupts are enabled/disabled in more places than just m_can_start()
and m_can_stop(). Couple the polling timer with enabling/disabling of
all interrupts to achieve equivalent behavior.
Cc: Judith Mendez <jm@ti.com>
Fixes: b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-2-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5bd4041cd ]
The firmware (later) actually uses the values even for keys
that are invalid as far as the host is concerned, later in
rekeying, and then only sets the low 48 bits since the PNs
are only 48 bits over the air. It does, however, compare the
full 64 bits later, obviously causing problems.
Remove the memset and use kzalloc instead to avoid any old
heap data leaking to the firmware. We already init all the
other fields in the struct anyway. This leaves the data set
to zero for any unused fields, so the firmware can look at
them safely even if they're not used right now.
Fixes: 79e561f0f0 ("iwlwifi: mvm: d3: implement RSC command version 5")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.462101146fef.I10f3855b99417af4247cff04af78dcbc6cb75c9c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e35f316bce ]
The firmware doesn't need the MFP flag for the GTK, it can even make the
firmware crash. in case the AP is configured with: group cipher TKIP and
MFPC. We would send the GTK with cipher = TKIP and MFP which is of course
not possible.
Fixes: 5c75a208c2 ("wifi: iwlwifi: mvm: support new key API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.2f2c602ab3c6.If13b2e2fa532381d985c07df130bee1478046c89@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e0e766bd8 ]
When retrieving the queue index ("SCD SSN") from the TX response,
it's currently masked with 0xFFF. However, now that we have queues
longer than 4k, that became wrong, so make the mask depend on the
hardware family.
This fixes an issue where if we get a single frame reclaim while
in the top half of an 8k long queue, we'd reclaim-wrap the queue
twice (once on this and then again on the next non-single reclaim)
which at least triggers the WARN_ON_ONCE() in iwl_txq_reclaim(),
but could have other negative side effects (such as unmapping a
frame that wasn't transmitted yet, and then taking an IOMMU fault)
as well.
Fixes: 7b3e42ea2e ("iwlwifi: support multiple tfd queue max sizes for different devices")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.4148a6ef54e0.I733a70f679c25f9f99097a8dcb3a1f8165da6997@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f51d643182 ]
sku_cap_11be_enable should be set to true also for WH.
Fixes: e1374ed253 ("wifi: iwlwifi: Add support for new CNVi (SC)")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240204235836.a6d4097cbaca.I8b00fa7b6226b4116cd91f70fb0b15e79b4dee5a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 019b58dcb6 ]
During calculate vdev_stats_id, will compare vdev_stats_id with
ATH12K_INVAL_VDEV_STATS_ID by '<='. If vdev_stats_id is relatively
small, then assign ATH12K_INVAL_VDEV_STATS_ID to vdev_stats_id.
This logic is incorrect. Firstly, should use '>=' instead of '<=' to
check if this u8 variable exceeds the max valid range.
Secondly, should use the maximum value as comparison value.
Correct comparison symbols and use the maximum value
ATH12K_MAX_VDEV_STATS_ID for comparison.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-3-quic_kangyang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
