[ Upstream commit 3c466d6537 ]
On sa8775p-ride-r3 the RX clocks from the AQR115C PHY are not available at
the time of the DMA reset. We can however extract the RX clock from the
internal SERDES block. Once the link is up, we can revert to the
previous state.
The AQR115C PHY doesn't support in-band signalling so we can count on
getting the link up notification and safely reuse existing callbacks
which are already used by another HW quirk workaround which enables the
functional clock to avoid a DMA reset due to timeout.
Only enable loopback on revision 3 of the board - check the phy_mode to
make sure.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240703181500.28491-3-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a0a88fcba ]
This patch updates the workaround for a problem similar to erratum
DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. As the FIFO
is implemented as a ring buffer, this results in re-handling old CAN
transmit complete events.
Every transmit complete event contains with a sequence number that
equals to the sequence number of the corresponding TX request. This
way old TX complete events can be detected.
If the original driver detects a non matching sequence number, it
prints an info message and tries again later. As wrong sequence
numbers can be explained by the erratum DS80000789E 6, demote the info
message to debug level, streamline the code and update the comments.
Keep the behavior: If an old CAN TX complete event is detected, abort
the iteration and mark the number of valid CAN TX complete events as
processed in the chip by incrementing the FIFO's tail index.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8e0ddd36c ]
This is a preparatory patch to work around a problem similar to
erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
When handling the TEF interrupt, the driver reads the FIFO header
index from the TEF FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN transmit complete events that were already processed to be
re-processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_tef_ring_update() with mcp251xfd_get_tef_len().
The mcp251xfd_handle_tefif() function reads the CAN transmit complete
events from the chip, iterates over them and pushes them into the
network stack. The original driver already contains code to detect old
CAN transmit complete events, that will be updated in the next patch.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fba8334721 ]
When all the strides in a WQE have been consumed, the WQE is unlinked
from the WQ linked list (mlx5_wq_ll_pop()). For SHAMPO, it is possible
to receive CQEs with 0 consumed strides for the same WQE even after the
WQE is fully consumed and unlinked. This triggers an additional unlink
for the same wqe which corrupts the linked list.
Fix this scenario by accepting 0 sized consumed strides without
unlinking the WQE again.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240603212219.1037656-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d60041543 ]
Currently the resource allocated by crypto_alloc_shash() is not
freed in case ath12k_peer_find() fails, resulting in memory leak.
Add crypto_free_shash() to fix it.
This is found during code review, compile tested only.
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240526124226.24661-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ee09edc05 ]
Some Wake-on-LAN modes such as WAKE_FILTER may only be supported by the MAC,
while others might be only supported by the PHY. Make sure that the .get_wol()
returns the union of both rather than only that of the PHY if the PHY supports
Wake-on-LAN.
Fixes: 7e400ff35c ("net: bcmgenet: Add support for PHY-based Wake-on-LAN")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806175659.3232204-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3862093ee ]
bcm_sf2_mdio_register() calls of_phy_find_device() and then
phy_device_remove() in a loop to remove existing PHY devices.
of_phy_find_device() eventually calls bus_find_device(), which calls
get_device() on the returned struct device * to increment the refcount.
The current implementation does not decrement the refcount, which causes
memory leak.
This commit adds the missing phy_device_free() call to decrement the
refcount via put_device() to balance the refcount.
Fixes: 771089c2a4 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806011327.3817861-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a47f3320bb ]
The ext interrupts are enabled when the firmware has been started, but
this may never happen, for example, if the board configuration file is
missing.
When the system is later suspended, the driver unconditionally tries to
disable interrupts, which results in an irq disable imbalance and causes
the driver to spin indefinitely in napi_synchronize().
Make sure that the interrupts have been enabled before attempting to
disable them.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240709073132.9168-1-johan+linaro@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 604308a344 ]
Add two flags to indicate whether IRQ handler for CE and DP can be called.
This is because in one MSI vector case, interrupt is not disabled in
hif_stop and hif_irq_disable. So if interrupt is disabled, MHI interrupt
is disabled too.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-3-quic_kangyang@quicinc.com
Stable-dep-of: a47f3320bb ("wifi: ath12k: fix soft lockup on suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cda8607e82 ]
In PCI and HAL interface layer module, the identifier sc is used
to represent an instance of ath12k_base structure. However,
within ath12k, the convention is to use "ab" to represent an SoC
"base" struct. So change the all instances of sc to ab.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231018153008.29820-3-quic_periyasa@quicinc.com
Stable-dep-of: a47f3320bb ("wifi: ath12k: fix soft lockup on suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 08f3a5c380 upstream.
It could lead to error happen because the variable res is not updated if
the call to sr_share_read_word returns an error. In this particular case
error code was returned and res stayed uninitialized. Same issue also
applies to sr_read_reg.
This can be avoided by checking the return value of sr_share_read_word
and sr_read_reg, and propagating the error if the read operation failed.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b9e7fc0aed ]
Following the implementation of "igc: Add TransmissionOverrun counter"
patch, when a taprio command is triggered by user, igc processes two
commands: TAPRIO_CMD_REPLACE followed by TAPRIO_CMD_STATS. However, both
commands unconditionally pass through igc_tsn_offload_apply() which
evaluates and triggers reset adapter. The double reset causes issues in
the calculation of adapter->qbv_count in igc.
TAPRIO_CMD_REPLACE command is expected to reset the adapter since it
activates qbv. It's unexpected for TAPRIO_CMD_STATS to do the same
because it doesn't configure any driver-specific TSN settings. So, the
evaluation in igc_tsn_offload_apply() isn't needed for TAPRIO_CMD_STATS.
To address this, commands parsing are relocated to
igc_tsn_enable_qbv_scheduling(). Commands that don't require an adapter
reset will exit after processing, thus avoiding igc_tsn_offload_apply().
Fixes: d3750076d4 ("igc: Add TransmissionOverrun counter")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240730173304.865479-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f8e82a020 ]
Since the documentation for mlx5_toggle_port_link states that it should
only be used after setting the port register, we add a check for the
return value from mlx5_port_set_eth_ptys to ensure the register was
successfully set before calling it.
Fixes: 667daedaec ("net/mlx5e: Toggle link only after modifying port parameters")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-9-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 025f2b85a5 ]
The cited commit allocates a new modify header to replace the old
one when updating CT entry. But if failed to allocate a new one, eg.
exceed the max number firmware can support, modify header will be
an error pointer that will trigger a panic when deallocating it. And
the old modify header point is copied to old attr. When the old
attr is freed, the old modify header is lost.
Fix it by restoring the old attr to attr when failed to allocate a
new modify header context. So when the CT entry is freed, the right
modify header context will be freed. And the panic of accessing
error pointer is also fixed.
Fixes: 94ceffb48e ("net/mlx5e: Implement CT entry update")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-8-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06827e27fd ]
Require mlx5 classifier action support when creating IPSec chains in
offload path. MLX5_IPSEC_CAP_PRIO should only be set if CONFIG_MLX5_CLS_ACT
is enabled. If CONFIG_MLX5_CLS_ACT=n and MLX5_IPSEC_CAP_PRIO is set,
configuring IPsec offload will fail due to the mlxx5 ipsec chain rules
failing to be created due to lack of classifier action support.
Fixes: fa5aa2f890 ("net/mlx5e: Use chains for IPsec policy priority offload")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fda84dc09 ]
The cited commit didn't change the body of the loop as it should.
It shouldn't be using MLX5_LAG_P1.
Fixes: 7e978e7714 ("net/mlx5: Lag, use actual number of lag ports")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4557b0b57 ]
In case mlx5_irq_alloc fails, the previously allocated index remains
in the XArray, which could lead to inconsistencies.
Fix it by adding error handling that erases the allocated index
from the XArray if mlx5_irq_alloc returns an error.
Fixes: c36326d38d ("net/mlx5: Round-Robin EQs over IRQs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b75da22ed ]
There is no point in recovery during device shutdown. if health
work started need to wait for it to avoid races and NULL pointer
access.
Hence, drain health WQ on shutdown callback.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Fixes: d2aa060d40 ("net/mlx5: Cancel health poll before sending panic teardown command")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84383b5ef4 ]
The MDIX status is not accurately reflecting the current state after the link
partner has manually altered its MDIX configuration while operating in forced
mode.
Access information about Auto mdix completion and pair selection from the
KSZ9131's Auto/MDI/MDI-X status register
Fixes: b64e6a8794 ("net: phy: micrel: Add PHY Auto/MDI/MDI-X set driver for KSZ9131")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240725071125.13960-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aa3ca956c ]
This function has a nested loop. The problem is that both the inside
and outside loop use the same variable as an iterator. I found this
via static analysis so I'm not sure the impact. It could be that it
loops forever or, more likely, the loop exits early.
Fixes: 3a616b92a9 ("net: mvpp2: Add TX flow control support for jumbo frames")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/eaa8f403-7779-4d81-973d-a9ecddc0bf6f@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6044ca2621 ]
It is read by data path and modified from process context on remote cpu
so it is needed to use WRITE_ONCE to clear the pointer.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 405d9999aa ]
Given that ice_qp_dis() is called under rtnl_lock, synchronize_net() can
be called instead of synchronize_rcu() so that XDP rings can finish its
job in a faster way. Also let us do this as earlier in XSK queue disable
flow.
Additionally, turn off regular Tx queue before disabling irqs and NAPI.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ff72a2f67 ]
When ice driver is spammed with multiple xdpsock instances and flow
control is enabled, there are cases when Rx queue gets stuck and unable
to reflect the disable state in QRX_CTRL register. Similar issue has
previously been addressed in commit 13a6233b03 ("ice: Add support to
enable/disable all Rx queues before waiting").
To workaround this, let us simply not wait for a disabled state as later
patch will make sure that regardless of the encountered error in the
process of disabling a queue pair, the Rx queue will be enabled.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec145a1868 ]
Address a scenario in which XSK ZC Tx produces descriptors to XDP Tx
ring when link is either not yet fully initialized or process of
stopping the netdev has already started. To avoid this, add checks
against carrier readiness in ice_xsk_wakeup() and in ice_xmit_zc().
One could argue that bailing out early in ice_xsk_wakeup() would be
sufficient but given the fact that we produce Tx descriptors on behalf
of NAPI that is triggered for Rx traffic, the latter is also needed.
Bringing link up is an asynchronous event executed within
ice_service_task so even though interface has been brought up there is
still a time frame where link is not yet ok.
Without this patch, when AF_XDP ZC Tx is used simultaneously with stack
Tx, Tx timeouts occur after going through link flap (admin brings
interface down then up again). HW seem to be unable to transmit
descriptor to the wire after HW tail register bump which in turn causes
bit __QUEUE_STATE_STACK_XOFF to be set forever as
netdev_tx_completed_queue() sees no cleaned bytes on the input.
Fixes: 126cdfe100 ("ice: xsk: Improve AF_XDP ZC Tx and use batching API")
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 799a829507 ]
softirq may get lost if an Rx interrupt comes before we call
napi_enable. Move napi_enable in front of axienet_setoptions(), which
turns on the device, to address the issue.
Link: https://lists.gnu.org/archive/html/qemu-devel/2024-07/msg06160.html
Fixes: cc37610caa ("net: axienet: implement NAPI and GRO receive")
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225990c487 ]
The PHY built in to the Realtek RTL8366S switch controller was
previously supported by genphy_driver. This PHY does not implement MMD
operations. Since commit 9b01c885be ("net: phy: c22: migrate to
genphy_c45_write_eee_adv()"), MMD register reads have been made during
phy_probe to determine EEE support. For genphy_driver, these reads are
transformed into 802.3 annex 22D clause 45-over-clause 22
mmd_phy_indirect operations that perform MII register writes to
MII_MMD_CTRL and MII_MMD_DATA. This overwrites those two MII registers,
which on this PHY are reserved and have another function, rendering the
PHY unusable while so configured.
Proper support for this PHY is restored by providing a phy_driver that
declares MMD operations as unsupported by using the helper functions
provided for that purpose, while remaining otherwise identical to
genphy_driver.
Fixes: 9b01c885be ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
Reported-by: Russell Senior <russell@personaltelco.net>
Closes: https://github.com/openwrt/openwrt/issues/15981
Link: https://github.com/openwrt/openwrt/issues/15739
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9dbebae2e ]
The perfect_match parameter of the update_vlan_hash operation is __le16,
and is correctly converted from host byte-order in the lone caller,
stmmac_vlan_update().
However, the implementations of this caller, dwxgmac2_update_vlan_hash()
and dwxgmac2_update_vlan_hash(), both treat this parameter as host byte
order, using the following pattern:
u32 value = ...
...
writel(value | perfect_match, ...);
This is not correct because both:
1) value is host byte order; and
2) writel expects a host byte order value as it's first argument
I believe that this will break on big endian systems. And I expect it
has gone unnoticed by only being exercised on little endian systems.
The approach taken by this patch is to update the callback, and it's
caller to simply use a host byte order value.
Flagged by Sparse.
Compile tested only.
Fixes: c7ab0b8088 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19abb9c2b9 ]
When ice driver reads recipes from firmware information about
need_pass_l2 and allow_pass_l2 flags is not stored correctly.
Those flags are stored as one bit each in ice_sw_recipe structure.
Because of that, the result of checking a flag has to be casted to bool.
Note that the need_pass_l2 flag currently works correctly, because
it's stored in the first bit.
Fixes: bccd9bce29 ("ice: Add guard rule when creating FDB in switchdev")
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ba359c0cd ]
RCU use in bond_should_notify_peers() looks wrong, since it does
rcu_dereference(), leaves the critical section, and uses the
pointer after that.
Luckily, it's called either inside a nested RCU critical section
or with the RTNL held.
Annotate it with rcu_dereference_rtnl() instead, and remove the
inner RCU critical section.
Fixes: 4cb4f97b7e ("bonding: rebuild the lock use for bond_mii_monitor()")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20240719094119.35c62455087d.I68eb9c0f02545b364b79a59f2110f2cf5682a8e2@changeid
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6ebbe97a48 upstream.
While the iavf driver adds a s/w limit (128) on the number of FDIR
filters that the VF can request, a malicious VF driver can request more
than that and exhaust the resources for other VFs.
Add a similar limit in ice.
CC: stable@vger.kernel.org
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Suggested-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36e3b949e3 upstream.
The NIC requires each TSO segment to not span more than 10
descriptors. NIC further requires each descriptor to not exceed
16KB - 1 (GVE_TX_MAX_BUF_SIZE_DQO).
The descriptors for an skb are generated by
gve_tx_add_skb_no_copy_dqo() for DQO RDA queue format.
gve_tx_add_skb_no_copy_dqo() loops through each skb frag and
generates a descriptor for the entire frag if the frag size is
not greater than GVE_TX_MAX_BUF_SIZE_DQO. If the frag size is
greater than GVE_TX_MAX_BUF_SIZE_DQO, it is split into descriptor(s)
of size GVE_TX_MAX_BUF_SIZE_DQO and a descriptor is generated for
the remainder (frag size % GVE_TX_MAX_BUF_SIZE_DQO).
gve_can_send_tso() checks if the descriptors thus generated for an
skb would meet the requirement that each TSO-segment not span more
than 10 descriptors. However, the current code misses an edge case
when a TSO segment spans multiple descriptors within a large frag.
This change fixes the edge case.
gve_can_send_tso() relies on the assumption that max gso size (9728)
is less than GVE_TX_MAX_BUF_SIZE_DQO and therefore within an skb
fragment a TSO segment can never span more than 2 descriptors.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240724143431.3343722-1-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28818b4d87 upstream.
When there is beacon loss, for example due to unrelated Bluetooth
devices transmitting music nearby, the wifi connection dies soon
after the first beacon loss message:
Apr 28 20:47:14 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-BEACON-LOSS
Apr 28 20:47:15 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-DISCONNECTED bssid=... reason=4 locally_generated=1
Apr 28 20:47:24 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-BEACON-LOSS
Apr 28 20:47:25 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-DISCONNECTED bssid=... reason=4 locally_generated=1
Apr 28 20:47:34 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-BEACON-LOSS
Apr 28 20:47:35 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-DISCONNECTED bssid=... reason=4 locally_generated=1
When the beacon loss happens, mac80211 makes rtw88 transmit a QOS
NULL frame and asks to confirm the ACK status. Even though rtw88
confirms to mac80211 that the QOS NULL was transmitted successfully,
the connection still dies. This is because rtw88 is handing the QOS
NULL back to mac80211 with skb->data pointing to the headroom (the
TX descriptor) instead of ieee80211_hdr.
Fix the disconnection by moving skb->data to the correct position
before ieee80211_tx_status_irqsafe().
The problem was observed with RTL8811AU (TP-Link Archer T2U Nano)
and the potential future rtw88_8821au driver. Also tested with
RTL8811CU (Tenda U9).
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/ecbf0601-810d-4609-b8fc-8b0e38d2948d@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17b9f590f upstream.
When changing the interface type we also need to update the bss_num, the
driver private data is searched based on a unique (bss_type, bss_num)
tuple, therefore every time bss_type changes, bss_num must also change.
This fixes for example an issue in which, after the mode changed, a
wireless scan on the changed interface would not finish, leading to
repeated -EBUSY messages to userspace when other scan requests were
sent.
Fixes: c606008b70 ("mwifiex: Properly initialize private structure on interface type changes")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240510110458.15475-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97d9fba9a8 upstream.
Currently, netconsole cleans up the netpoll structure before disabling
the target. This approach can lead to race conditions, as message
senders (write_ext_msg() and write_msg()) check if the target is
enabled before using netpoll. The sender can validate that the target is
enabled, but, the netpoll might be de-allocated already, causing
undesired behaviours.
This patch reverses the order of operations:
1. Disable the target
2. Clean up the netpoll structure
This change eliminates the potential race condition, ensuring that
no messages are sent through a partially cleaned-up netpoll structure.
Fixes: 2382b15bcc ("netconsole: take care of NETDEV_UNREGISTER event")
Cc: stable@vger.kernel.org
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240712143415.1141039-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5118072e2 ]
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame
configuration. In the commit referenced with the Fixes tag, the setting
is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient chip-wide maximum frame size for the CPU port.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports. This aligns the driver
to the behavior of other switch drivers.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66b6095c26 ]
Marvell chips not supporting per-port jumbo frame size configurations use
a chip-wide frame size configuration. In the commit referenced with the
Fixes tag, the setting is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient maximum frame size for the CPU port. Specifically, sending
full-size frames from the CPU port on a MV88E6097 having a user port MTU
of 1500 bytes results in dropped frames.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03b54bad26 ]
In gve_clean_xdp_done, the driver processes the TX completions based on
a 32-bit NIC counter and a 32-bit completion counter stored in the tx
queue.
Fix the for loop so that the counter wraparound is handled correctly.
Fixes: 75eaae158b ("gve: Add XDP DROP and TX support for GQI-QPL format")
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240716171041.1561142-1-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9741a03dc ]
To have enough space to write all possible sprintf() args. Currently
'name' size is 16, but the first '%s' specifier may already need at
least 16 characters, since 'bnad->netdev->name' is used there.
For '%d' specifiers, assume that they require:
* 1 char for 'tx_id + tx_info->tcb[i]->id' sum, BNAD_MAX_TXQ_PER_TX is 8
* 2 chars for 'rx_id + rx_info->rx_ctrl[i].ccb->id', BNAD_MAX_RXP_PER_RX
is 16
And replace sprintf with snprintf.
Detected using the static analysis tool - Svace.
Fixes: 8b230ed8ec ("bna: Brocade 10Gb Ethernet device driver")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5d14b0c67 ]
When user issues a connection with a different SSID than the one
virt_wifi has advertised, the __cfg80211_connect_result() will
trigger the warning: WARN_ON(bss_not_found).
The issue is because the connection code in virt_wifi does not
check the SSID from user space (it only checks the BSSID), and
virt_wifi will call cfg80211_connect_result() with WLAN_STATUS_SUCCESS
even if the SSID is different from the one virt_wifi has advertised.
Eventually cfg80211 won't be able to find the cfg80211_bss and generate
the warning.
Fixed it by checking the SSID (from user space) in the connection code.
Fixes: c7cdba31ed ("mac80211-next: rtnetlink wifi simulation device")
Reported-by: syzbot+d6eb9cee2885ec06f5e3@syzkaller.appspotmail.com
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Link: https://patch.msgid.link/20240705023756.10954-1-en-wei.wu@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85099c7ce4 ]
In rtw89_sta_info_get_iter() 'status->he_gi' is compared to array size.
But then 'rate->he_gi' is used as array index instead of 'status->he_gi'.
This can lead to go beyond array boundaries in case of 'rate->he_gi' is
not equal to 'status->he_gi' and is bigger than array size. Looks like
"copy-paste" mistake.
Fix this mistake by replacing 'rate->he_gi' with 'status->he_gi'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240703210510.11089-1-amishin@t-argos.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0b4b8ef08 ]
TX power index is read from the efuse on init, the values get written to
the TX power registers when the channel gets switched.
When the chip has not yet been calibrated, the efuse values are 0xFF,
which on some boards leads to USB timeouts for reading/writing registers
after the first frames have been sent.
The vendor driver (v5.11.5-1) checks for these invalid values and sets
default values instead. Implement something similar in
rtl8188fu_parse_efuse().
Fixes: c888183b21 ("wifi: rtl8xxxu: Support new chip RTL8188FU")
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240624140037.231657-1-martin.kaistra@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f35712ab8 ]
An incorrect definition caused DPK to fail to backup and
restore a set of KIP registers. Fixing this will improve
RX throughput from 902 to 997 Mbps.
Fixes: 5b8471ace5 ("wifi: rtw89: 8852b: rfk: add DPK")
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240621123617.6687-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c32fe1986f ]
FEC_ECR_EN1588 bit gets cleared after MAC reset in `fec_stop()`, which
makes all 1588 functionality shut down, and all the extended registers
disappear, on link-down, making the adapter fall back to compatibility
"dumb mode". However, some functionality needs to be retained (e.g. PPS)
even without link.
Fixes: 6605b730c0 ("FEC: Add time stamping code and a PTP hardware clock")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/netdev/5fa9fadc-a89d-467a-aae9-c65469ff5fe1@lunn.ch/
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
