[ Upstream commit 24436be590 ]
This patch tries to works around erratum DS80000789E 6 of the
mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old, already processed CAN frames or new, incompletely written CAN
frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp [1] of the last
valid received CAN frame and compare against the timestamp of every
received CAN frame. If an old CAN frame is detected, abort the
iteration and mark the number of valid CAN frames as processed in the
chip by incrementing the FIFO's tail index.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames [2] are not recognized but then processed. These CAN frames
have the correct data and time stamps, but the DLC has not yet been
updated.
[1] As the raw timestamp overflows every 107 seconds (at the usual
clock rate of 40 MHz) convert it to nanoseconds with the
timecounter framework and use this to detect stale CAN frames.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com [2]
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e793c724b4 ]
The mcp251xfd chip is configured to provide a timestamp with each
received and transmitted CAN frame. The timestamp is derived from the
internal free-running timer, which can also be read from the TBC
register via SPI. The timer is 32 bits wide and is clocked by the
external oscillator (typically 20 or 40 MHz).
To avoid confusion, we call this timestamp "timestamp_raw" or "ts_raw"
for short.
Using the timecounter framework, the "ts_raw" is converted to 64 bit
nanoseconds since the epoch. This is what we call "timestamp".
This is a preparation for the next patches which use the "timestamp"
to work around a bug where so far only the "ts_raw" is used.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85505e5856 ]
This is a preparatory patch to work around erratum DS80000789E 6 of
the mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
When handling the RX interrupt, the driver iterates over all pending
FIFOs (which are implemented as ring buffers in hardware) and reads
the FIFO header index from the RX FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN frames that were already processed, or new, incompletely
written CAN frames to be (re-)processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_rx_ring_update() with mcp251xfd_get_rx_len().
The mcp251xfd_handle_rxif_ring() function reads the received CAN
frames from the chip, iterates over them and pushes them into the
network stack. Prepare that the iteration can be stopped if an old CAN
frame is detected. The actual code to detect old or incomplete frames
and abort will be added in the next patch.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d49184b7b5 ]
This is a preparation patch.
Sending the UINC messages followed by incrementing the tail pointer
will be called in more than one place in upcoming patches, so factor
this out into a separate function.
Also make mcp251xfd_handle_rxif_ring_uinc() safe to be called with a
"len" of 0.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ba54b1a276 upstream.
Refactoring of the field get conversion introduced a regression in the
legacy Wake On Lan from a magic packet with i219 devices. Rx address
copied not correctly from MAC to PHY with FIELD_GET macro.
Fixes: b9a4525450 ("intel: legacy: field get conversion")
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Florian Larysch <fl@n621.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5876b088b ]
ipheth_sndbulk_callback() can submit carrier_work
as a part of its error handling. That means that
the driver must make sure that the work is cancelled
after it has made sure that no more URB can terminate
with an error condition.
Hence the order of actions in ipheth_close() needs
to be inverted.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555a05d84c ]
The dpaa-eth driver is written for PowerPC and Arm SoCs which have 1-24
CPUs. It depends on CONFIG_NR_CPUS having a reasonably small value in
Kconfig. Otherwise, there are 2 functions which allocate on-stack arrays
of NR_CPUS elements, and these can quickly explode in size, leading to
warnings such as:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:3280:12: warning:
stack frame size (16664) exceeds limit (2048) in 'dpaa_eth_probe' [-Wframe-larger-than]
The problem is twofold:
- Reducing the array size to the boot-time num_possible_cpus() (rather
than the compile-time NR_CPUS) creates a variable-length array,
which should be avoided in the Linux kernel.
- Using NR_CPUS as an array size makes the driver blow up in stack
consumption with generic, as opposed to hand-crafted, .config files.
A simple solution is to use dynamic allocation for num_possible_cpus()
elements (aka a small number determined at runtime).
Link: https://lore.kernel.org/all/202406261920.l5pzM1rj-lkp@intel.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://patch.msgid.link/20240713225336.1746343-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adc539784c ]
Right now it's possible to hit NULL pointer dereference in
rtw_rx_fill_rx_status on hw object and/or its fields because
initialization routine can start getting USB replies before
rtw_dev is fully setup.
The stack trace looks like this:
rtw_rx_fill_rx_status
rtw8821c_query_rx_desc
rtw_usb_rx_handler
...
queue_work
rtw_usb_read_port_complete
...
usb_submit_urb
rtw_usb_rx_resubmit
rtw_usb_init_rx
rtw_usb_probe
So while we do the async stuff rtw_usb_probe continues and calls
rtw_register_hw, which does all kinds of initialization (e.g.
via ieee80211_register_hw) that rtw_rx_fill_rx_status relies on.
Fix this by moving the first usb_submit_urb after everything
is set up.
For me, this bug manifested as:
[ 8.893177] rtw_8821cu 1-1:1.2: band wrong, packet dropped
[ 8.910904] rtw_8821cu 1-1:1.2: hw->conf.chandef.chan NULL in rtw_rx_fill_rx_status
because I'm using Larry's backport of rtw88 driver with the NULL
checks in rtw_rx_fill_rx_status.
Link: https://lore.kernel.org/linux-wireless/CA+shoWQ7P49jhQasofDcTdQhiuarPTjYEDa--NiVVx494WcuQw@mail.gmail.com/
Signed-off-by: Marcin Ślusarz <mslusarz@renau.com>
Cc: Tim K <tpkuester@gmail.com>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240528110246.477321-1-marcin.slusarz@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8487b4af59 ]
generic_ocp_write() asks the parameter "size" must be 4 bytes align.
Therefore, write the bp would fail, if the mac->bp_num is odd. Align the
size to 4 for fixing it. The way may write an extra bp, but the
rtl8152_is_fw_mac_ok() makes sure the value must be 0 for the bp whose
index is more than mac->bp_num. That is, there is no influence for the
firmware.
Besides, I check the return value of generic_ocp_write() to make sure
everything is correct.
Fixes: e5c266a611 ("r8152: set bp in bulk")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20240903063333.4502-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bab8eb0dd4 ]
The driver generates a random MAC once on load
and uses it over and over, including on two devices
needing a random MAC at the same time.
Jakub suggested revamping the driver to the modern
API for setting a random MAC rather than fixing
the old stuff.
The bug is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://patch.msgid.link/20240829175201.670718-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04c7e14e5b ]
After XDP configuration is completed, we bring the interface up
unconditionally, regardless of its state before the call to .ndo_bpf().
Preserve the information whether the interface had to be brought down and
later bring it up only in such case.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2504b84057 ]
The main threat to data consistency in ice_xdp() is a possible asynchronous
PF reset. It can be triggered by a user or by TX timeout handler.
XDP setup and PF reset code access the same resources in the following
sections:
* ice_vsi_close() in ice_prepare_for_reset() - already rtnl-locked
* ice_vsi_rebuild() for the PF VSI - not protected
* ice_vsi_open() - already rtnl-locked
With an unfortunate timing, such accesses can result in a crash such as the
one below:
[ +1.999878] ice 0000:b1:00.0: Registered XDP mem model MEM_TYPE_XSK_BUFF_POOL on Rx ring 14
[ +2.002992] ice 0000:b1:00.0: Registered XDP mem model MEM_TYPE_XSK_BUFF_POOL on Rx ring 18
[Mar15 18:17] ice 0000:b1:00.0 ens801f0np0: NETDEV WATCHDOG: CPU: 38: transmit queue 14 timed out 80692736 ms
[ +0.000093] ice 0000:b1:00.0 ens801f0np0: tx_timeout: VSI_num: 6, Q 14, NTC: 0x0, HW_HEAD: 0x0, NTU: 0x0, INT: 0x4000001
[ +0.000012] ice 0000:b1:00.0 ens801f0np0: tx_timeout recovery level 1, txqueue 14
[ +0.394718] ice 0000:b1:00.0: PTP reset successful
[ +0.006184] BUG: kernel NULL pointer dereference, address: 0000000000000098
[ +0.000045] #PF: supervisor read access in kernel mode
[ +0.000023] #PF: error_code(0x0000) - not-present page
[ +0.000023] PGD 0 P4D 0
[ +0.000018] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ +0.000023] CPU: 38 PID: 7540 Comm: kworker/38:1 Not tainted 6.8.0-rc7 #1
[ +0.000031] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0014.082620210524 08/26/2021
[ +0.000036] Workqueue: ice ice_service_task [ice]
[ +0.000183] RIP: 0010:ice_clean_tx_ring+0xa/0xd0 [ice]
[...]
[ +0.000013] Call Trace:
[ +0.000016] <TASK>
[ +0.000014] ? __die+0x1f/0x70
[ +0.000029] ? page_fault_oops+0x171/0x4f0
[ +0.000029] ? schedule+0x3b/0xd0
[ +0.000027] ? exc_page_fault+0x7b/0x180
[ +0.000022] ? asm_exc_page_fault+0x22/0x30
[ +0.000031] ? ice_clean_tx_ring+0xa/0xd0 [ice]
[ +0.000194] ice_free_tx_ring+0xe/0x60 [ice]
[ +0.000186] ice_destroy_xdp_rings+0x157/0x310 [ice]
[ +0.000151] ice_vsi_decfg+0x53/0xe0 [ice]
[ +0.000180] ice_vsi_rebuild+0x239/0x540 [ice]
[ +0.000186] ice_vsi_rebuild_by_type+0x76/0x180 [ice]
[ +0.000145] ice_rebuild+0x18c/0x840 [ice]
[ +0.000145] ? delay_tsc+0x4a/0xc0
[ +0.000022] ? delay_tsc+0x92/0xc0
[ +0.000020] ice_do_reset+0x140/0x180 [ice]
[ +0.000886] ice_service_task+0x404/0x1030 [ice]
[ +0.000824] process_one_work+0x171/0x340
[ +0.000685] worker_thread+0x277/0x3a0
[ +0.000675] ? preempt_count_add+0x6a/0xa0
[ +0.000677] ? _raw_spin_lock_irqsave+0x23/0x50
[ +0.000679] ? __pfx_worker_thread+0x10/0x10
[ +0.000653] kthread+0xf0/0x120
[ +0.000635] ? __pfx_kthread+0x10/0x10
[ +0.000616] ret_from_fork+0x2d/0x50
[ +0.000612] ? __pfx_kthread+0x10/0x10
[ +0.000604] ret_from_fork_asm+0x1b/0x30
[ +0.000604] </TASK>
The previous way of handling this through returning -EBUSY is not viable,
particularly when destroying AF_XDP socket, because the kernel proceeds
with removal anyway.
There is plenty of code between those calls and there is no need to create
a large critical section that covers all of them, same as there is no need
to protect ice_vsi_rebuild() with rtnl_lock().
Add xdp_state_lock mutex to protect ice_vsi_rebuild() and ice_xdp().
Leaving unprotected sections in between would result in two states that
have to be considered:
1. when the VSI is closed, but not yet rebuild
2. when VSI is already rebuild, but not yet open
The latter case is actually already handled through !netif_running() case,
we just need to adjust flag checking a little. The former one is not as
trivial, because between ice_vsi_close() and ice_vsi_rebuild(), a lot of
hardware interaction happens, this can make adding/deleting rings exit
with an error. Luckily, VSI rebuild is pending and can apply new
configuration for us in a managed fashion.
Therefore, add an additional VSI state flag ICE_VSI_REBUILD_PENDING to
indicate that ice_xdp() can just hot-swap the program.
Also, as ice_vsi_rebuild() flow is touched in this patch, make it more
consistent by deconfiguring VSI when coalesce allocation fails.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2560db6ede ]
The call of of_get_child_by_name() will cause refcount incremented
for leds, if it succeeds, it should call of_node_put() to decrease
it, fix it.
Fixes: 01e5b728e9 ("net: phy: Add a binding for PHY LEDs")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240830022025.610844-1-ruanjinjie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef4a99a016 ]
Call rtnl_unlock() on this error path, before returning.
Fixes: bc23aa949a ("igc: Add pcie error handler support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd885d90c0 ]
Kvaser's PCIe cards uses the KCAN FPGA IP block which has dual 4K
buffers for incoming messages shared by all (currently up to eight)
channels. While the driver processes messages in one buffer, new
incoming messages are stored in the other and so on.
The design of KCAN is such that a buffer must be fully read and then
released. Releasing a buffer will make the FPGA switch buffers. If the
other buffer contains at least one incoming message the FPGA will also
instantly issue a new interrupt, if not the interrupt will be issued
after receiving the first new message.
With IRQx interrupts, it takes a little time for the interrupt to
happen, enough for any previous ISR call to do it's business and
return, but MSI interrupts are way faster so this time is reduced to
almost nothing.
So with MSI, releasing the buffer HAS to be the very last action of
the ISR before returning, otherwise the new interrupt might be
"masked" by the kernel because the previous ISR call hasn't returned.
And the interrupts are edge-triggered so we cannot loose one, or the
ping-pong reading process will stop.
This is why this patch modifies the driver to use a single write to
the SRB_CMD register before returning.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20240830153113.2081440-1-martin.jocic@kvaser.com
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48f827d4f4 ]
A new interrupt is triggered by resetting the DMA RX buffers.
Since MSI interrupts are faster than legacy interrupts, the reset
of the DMA buffers must be moved to the very end of the ISR,
otherwise a new MSI interrupt will be masked by the current one.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240620181320.235465-2-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c0 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf88a6ba7 ]
Rename the variable name board_irq in the ISR to pci_irq to
be more specific and to match the macro by which it is read.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-7-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c0 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d186697c ]
The code speaks for itself.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-4-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c0 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac765219c2 ]
This check is already done at the creation of the net devices in
kvaser_pciefd_setup_can_ctrls called from kvaser_pciefd_probe.
If it fails, the driver won't load, so there should be no need to
repeat the check inside the ISR. The number of channels is read
from the FPGA and should be trusted.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-3-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c0 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d11a676342 ]
Ethtool callbacks can be executed while reset is in progress and try to
access deleted resources, e.g. getting coalesce settings can result in a
NULL pointer dereference seen below.
Reproduction steps:
Once the driver is fully initialized, trigger reset:
# echo 1 > /sys/class/net/<interface>/device/reset
when reset is in progress try to get coalesce settings using ethtool:
# ethtool -c <interface>
BUG: kernel NULL pointer dereference, address: 0000000000000020
PGD 0 P4D 0
Oops: Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 11 PID: 19713 Comm: ethtool Tainted: G S 6.10.0-rc7+ #7
RIP: 0010:ice_get_q_coalesce+0x2e/0xa0 [ice]
RSP: 0018:ffffbab1e9bcf6a8 EFLAGS: 00010206
RAX: 000000000000000c RBX: ffff94512305b028 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9451c3f2e588 RDI: ffff9451c3f2e588
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: ffff9451c3f2e580 R11: 000000000000001f R12: ffff945121fa9000
R13: ffffbab1e9bcf760 R14: 0000000000000013 R15: ffffffff9e65dd40
FS: 00007faee5fbe740(0000) GS:ffff94546fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000020 CR3: 0000000106c2e005 CR4: 00000000001706f0
Call Trace:
<TASK>
ice_get_coalesce+0x17/0x30 [ice]
coalesce_prepare_data+0x61/0x80
ethnl_default_doit+0xde/0x340
genl_family_rcv_msg_doit+0xf2/0x150
genl_rcv_msg+0x1b3/0x2c0
netlink_rcv_skb+0x5b/0x110
genl_rcv+0x28/0x40
netlink_unicast+0x19c/0x290
netlink_sendmsg+0x222/0x490
__sys_sendto+0x1df/0x1f0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x82/0x160
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7faee60d8e27
Calling netif_device_detach() before reset makes the net core not call
the driver when ethtool command is issued, the attempt to execute an
ethtool command during reset will result in the following message:
netlink error: No such device
instead of NULL pointer dereference. Once reset is done and
ice_rebuild() is executing, the netif_device_attach() is called to allow
for ethtool operations to occur again in a safe manner.
Fixes: fcea6f3da5 ("ice: Add stats and ethtool support")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba8cf80724 ]
82580 NICs have a hardware bug that makes it
necessary to write into the TSICR (TimeSync Interrupt Cause) register
to clear it:
https://lore.kernel.org/all/CDCB8BE0.1EC2C%25matthew.vick@intel.com/
Add a conditional so only for 82580 we write into the TSICR register,
so we don't risk losing events for other models.
Without this change, when running ptp4l with an Intel 82580 card,
I get the following output:
> timed out while polling for tx timestamp increasing tx_timestamp_timeout or
> increasing kworker priority may correct this issue, but a driver bug likely
> causes it
This goes away with this change.
This (partially) reverts commit ee14cc9ea1 ("igb: Fix missing time sync events").
Fixes: ee14cc9ea1 ("igb: Fix missing time sync events")
Closes: https://lore.kernel.org/intel-wired-lan/CAN0jFd1kO0MMtOh8N2Ztxn6f7vvDKp2h507sMryobkBKe=xk=w@mail.gmail.com/
Tested-by: Daiwei Li <daiweili@google.com>
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Daiwei Li <daiweili@google.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50ea5449c5 ]
If the ring (rx, tx) and/or coalescing parameters (rx-frames-irq,
tx-frames-irq) have been configured while the interface was in CAN-CC
mode, but the interface is brought up in CAN-FD mode, the ring
parameters might be too big.
Use the default CAN-FD values in this case.
Fixes: 9263c2e92b ("can: mcp251xfd: ring: add support for runtime configurable RX/TX ring parameters")
Link: https://lore.kernel.org/all/20240805-mcp251xfd-fix-ringconfig-v1-1-72086f0ca5ee@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06d4ef3056 ]
It appears that the irq requested in m_can_open() may be leaked
if an error subsequently occurs: if m_can_start() fails.
Address this by calling free_irq in the unwind path for
such cases.
Flagged by Smatch.
Compile tested only.
Fixes: eaacfeaca7 ("can: m_can: Call the RAM init directly from m_can_chip_config")
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240805-mcan-irq-v2-1-7154c0484819@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d47bf9a495 ]
Check the return value from ice_vsi_rebuild() and prevent the usage of
incorrectly configured VSI.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9215152677 ]
The lookup function iwl_mvm_rcu_fw_link_id_to_link_conf() is
normally called with input from the firmware, so it should use
IWL_FW_CHECK() instead of WARN_ON().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240625194805.4ea8fb7c47d4.I1c22af213f97f69bfc14674502511c1bc504adfb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db163a463b ]
Currently, if the access point receives an association
request containing an Extended HE Capabilities Information
Element with an invalid MCS-NSS, it triggers a firmware
crash.
This issue arises when EHT-PHY capabilities shows support
for a bandwidth and MCS-NSS set for that particular
bandwidth is filled by zeros and due to this, driver obtains
peer_nss as 0 and sending this value to firmware causes
crash.
Address this issue by implementing a validation step for
the peer_nss value before passing it to the firmware. If
the value is greater than zero, proceed with forwarding
it to the firmware. However, if the value is invalid,
reject the association request to prevent potential
firmware crashes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ajith C <quic_ajithc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240613053528.2541645-1-quic_ajithc@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19b77e7c65 ]
Smatch throws following errors
drivers/net/wireless/ath/ath12k/mac.c:1922 ath12k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
drivers/net/wireless/ath/ath12k/mac.c:1922 ath12k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_160'.
drivers/net/wireless/ath/ath12k/mac.c:1924 ath12k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
In ath12k_peer_assoc_h_he() rx_mcs_80 and rx_mcs_160 variables
remain uninitialized in the following conditions:
1. Whenever the value of mcs_80 become equal to
IEEE80211_HE_MCS_NOT_SUPPORTED then rx_mcs_80 remains uninitialized.
2. Whenever phy capability is not supported 160 channel width and
value of mcs_160 become equal to IEEE80211_HE_MCS_NOT_SUPPORTED
then rx_mcs_160 remains uninitialized.
Initialize these variables during declaration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240611031017.297927-3-quic_aarasahu@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f962e8361a upstream.
0x7d and 0x7e bytes are meant to be escaped in the data portion of
frames, but this didn't occur since next_chunk_len() had an off-by-one
error. That also resulted in the final byte of a payload being written
as a separate tty write op.
The chunk prior to an escaped byte would be one byte short, and the
next call would never test the txpos+1 case, which is where the escaped
byte was located. That meant it never hit the escaping case in
mctp_serial_tx_work().
Example Input: 01 00 08 c8 7e 80 02
Previous incorrect chunks from next_chunk_len():
01 00 08
c8 7e 80
02
With this fix:
01 00 08 c8
7e
80 02
Cc: stable@vger.kernel.org
Fixes: a0c2ccd9b5 ("mctp: Add MCTP-over-serial transport binding")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dd9c26bd6 upstream.
The mcp251x_hw_wake() function is called with the mpc_lock mutex held and
disables the interrupt handler so that no interrupts can be processed while
waking the device. If an interrupt has already occurred then waiting for
the interrupt handler to complete will deadlock because it will be trying
to acquire the same mutex.
CPU0 CPU1
---- ----
mcp251x_open()
mutex_lock(&priv->mcp_lock)
request_threaded_irq()
<interrupt>
mcp251x_can_ist()
mutex_lock(&priv->mcp_lock)
mcp251x_hw_wake()
disable_irq() <-- deadlock
Use disable_irq_nosync() instead because the interrupt handler does
everything while holding the mutex so it doesn't matter if it's still
running.
Fixes: 8ce8c0abcb ("can: mcp251x: only reset hardware as required")
Signed-off-by: Simon Arlott <simon@octiron.net>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/4fc08687-1d80-43fe-9f0d-8ef8475e75f6@0882a8b5-c6c3-11e9-b005-00805fc181fe.uuid.home.arpa
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3c1e45156 upstream.
This is a clear use-after-free error. We remove it, and rely on checking
the return code of vcap_del_rule.
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/kernel-janitors/7bffefc6-219a-4f71-baa0-ad4526e5c198@kili.mountain/
Fixes: c956b9b318 ("net: microchip: sparx5: Adding KUNIT tests of key/action values in VCAP API")
Signed-off-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8321fa751 upstream.
After the commit bdacf3e349 ("net: Use nested-BH locking for
napi_alloc_cache.") was merged, the following warning began to appear:
WARNING: CPU: 5 PID: 1 at net/core/skbuff.c:1451 napi_skb_cache_put+0x82/0x4b0
__warn+0x12f/0x340
napi_skb_cache_put+0x82/0x4b0
napi_skb_cache_put+0x82/0x4b0
report_bug+0x165/0x370
handle_bug+0x3d/0x80
exc_invalid_op+0x1a/0x50
asm_exc_invalid_op+0x1a/0x20
__free_old_xmit+0x1c8/0x510
napi_skb_cache_put+0x82/0x4b0
__free_old_xmit+0x1c8/0x510
__free_old_xmit+0x1c8/0x510
__pfx___free_old_xmit+0x10/0x10
The issue arises because virtio is assuming it's running in NAPI context
even when it's not, such as in the netpoll case.
To resolve this, modify virtnet_poll_tx() to only set NAPI when budget
is available. Same for virtnet_poll_cleantx(), which always assumed that
it was in a NAPI context.
Fixes: df133f3f96 ("virtio_net: bulk free tx skbs")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Link: https://patch.msgid.link/20240712115325.54175-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[Shivani: Modified to apply on v6.6.y]
Signed-off-by: Shivani Agarwal <shivani.agarwal@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70bd03b89f ]
Under the following conditions:
1) No skb created yet
2) header_size == 0 (no SHAMPO header)
3) header_index + 1 % MLX5E_SHAMPO_WQ_HEADER_PER_PAGE == 0 (this is the
last page fragment of a SHAMPO header page)
a new skb is formed with a page that is NOT a SHAMPO header page (it
is a regular data page). Further down in the same function
(mlx5e_handle_rx_cqe_mpwrq_shampo()), a SHAMPO header page from
header_index is released. This is wrong and it leads to SHAMPO header
pages being released more than once.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240603212219.1037656-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eb76e71b1 ]
Address a warning about potential string truncation based on the
string buffer sizes. We can add some hints to the string format
specifier to set limits on the resulting possible string to
squelch the complaints.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240529000259.25775-2-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37733bffda ]
fw_running assumes that memory can be retrieved only after alive.
This assumption is no longer true as we support dump before alive.
To avoid invalid access to the NIC, check that STATUS_DEVICE_ENABLED
bit in trans status is set before dumping instead of the prior check.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.ca07138cedeb.I090e31d3eaeb4ba19f5f84aba997ccd36927e9ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea4066588 ]
We did deinit CAM in STA iteration in VIF loop. But, the STA iteration
missed to restrict the target VIF. So, if there are multiple VIFs, we
would deinit a CAM multiple times. Now, fix it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240509090646.35304-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 199f149e97 ]
smatch flagged the following issue:
drivers/net/wireless/ath/ath11k/qmi.c:2401 ath11k_qmi_load_file_target_mem() error: uninitialized symbol 'ret'.
The reality is that 'ret' is initialized in every path through
ath11k_qmi_load_file_target_mem() except one, the case where the input
'len' is 0, and hence the "while (remaining)" loop is never entered.
But to make sure this case is also handled, add an initializer to the
declaration of 'ret'.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240504-qmi_load_file_target_mem-v1-2-069fc44c45eb@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb0b0a6b96 ]
smatch flagged the following issue:
drivers/net/wireless/ath/ath12k/qmi.c:2619 ath12k_qmi_load_file_target_mem() error: uninitialized symbol 'ret'.
The reality is that 'ret' is initialized in every path through
ath12k_qmi_load_file_target_mem() except one, the case where the input
'len' is 0, and hence the "while (remaining)" loop is never entered.
But to make sure this case is also handled, add an initializer to the
declaration of 'ret'.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240504-qmi_load_file_target_mem-v1-1-069fc44c45eb@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94a3ad6c08 ]
This patch reduces the size of hw_ste_arr_optimized array that is
allocated on stack from 640 bytes (5 match STEs + 5 action STES)
to 448 bytes (2 match STEs + 5 action STES).
This fixes the 'stack guard page was hit' issue, while still fitting
majority of the usecases (up to 2 match STEs).
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240730061638.1831002-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit defd8b3c37 ]
When sockfd_lookup() fails, gtp_encap_enable_socket() returns a
NULL pointer, but its callers only check for error pointers thus miss
the NULL pointer case.
Fix it by returning an error pointer with the error code carried from
sockfd_lookup().
(I found this bug during code inspection.)
Fixes: 1e3a3abd8b ("gtp: make GTP sockets in gtp_newlink optional")
Cc: Andreas Schultz <aschultz@tpip.net>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://patch.msgid.link/20240825191638.146748-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907ed83a75 ]
Add a local variable for slave->dev, to prepare for the lock change in
the next patch. There is no functionality change.
Fixes: 9a5605505d ("bonding: Add struct bond_ipesc to manage SA")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20240823031056.110999-3-jianbol@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec13009472 ]
Add this implementation for bonding, so hardware resources can be
freed from the active slave after xfrm state is deleted. The netdev
used to invoke xdo_dev_state_free callback, is saved in the xfrm state
(xs->xso.real_dev), which is also the bond's active slave. To prevent
it from being freed, acquire netdev reference before leaving RCU
read-side critical section, and release it after callback is done.
And call it when deleting all SAs from old active real interface while
switching current active slave.
Fixes: 9a5605505d ("bonding: Add struct bond_ipesc to manage SA")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20240823031056.110999-2-jianbol@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ee22f07a3 ]
Check size of WGDS revision 3 is equal to 8 entries size with some header,
but doesn't depend on the number of used entries. Check that used entries
are between min and max but allow more to be present than are used to fix
operation with some BIOSes that have such data.
Fixes: 97f8a3d161 ("iwlwifi: ACPI: support revision 3 WGDS tables")
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.cc71dfc67ec3.Ic27ee15ac6128b275c210b6de88f2145bd83ca7b@changeid
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8af174ea86 upstream.
The mana_hwc_rx_event_handler() / mana_hwc_handle_resp() calls
complete(&ctx->comp_event) before posting the wqe back. It's
possible that other callers, like mana_create_txq(), start the
next round of mana_hwc_send_request() before the posting of wqe.
And if the HW is fast enough to respond, it can hit no_wqe error
on the HW channel, then the response message is lost. The mana
driver may fail to create queues and open, because of waiting for
the HW response and timed out.
Sample dmesg:
[ 528.610840] mana 39d4:00:02.0: HWC: Request timed out!
[ 528.614452] mana 39d4:00:02.0: Failed to send mana message: -110, 0x0
[ 528.618326] mana 39d4:00:02.0 enP14804s2: Failed to create WQ object: -110
To fix it, move posting of rx wqe before complete(&ctx->comp_event).
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
