[ Upstream commit cbd7ec0834 ]
When sending packets under 60 bytes, up to three bytes of the buffer
following the data may be leaked. Avoid this by extending all packets to
ETH_ZLEN, ensuring nothing is leaked in the padding. This bug can be
reproduced by running
$ ping -s 11 destination
Fixes: 9ad1a37493 ("dpaa_eth: add support for DPAA Ethernet")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240910143144.1439910-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70654f4c21 ]
The TAS module could not be configured when it's running in pending
status. We need disable the module and configure it again. However, the
pending status is not cleared after the module disabled. TC taprio set
will always return busy even it's disabled.
For example, a user uses tc-taprio to configure Qbv and a future
basetime. The TAS module will run in a pending status. There is no way
to reconfigure Qbv, it always returns busy.
Actually the TAS module can be reconfigured when it's disabled. So it
doesn't need to check the pending status if the TAS module is disabled.
After the patch, user can delete the tc taprio configuration to disable
Qbv and reconfigure it again.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://patch.msgid.link/20240906093550.29985-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 019aba04f0 ]
The current implementation of SMQ flush sequence waits for the packets
in the TM pipeline to be transmitted out of the link. This sequence
doesn't succeed in HW when there is any issue with link such as lack of
link credits, link down or any other traffic that is fully occupying the
link bandwidth (QoS). This patch modifies the SMQ flush sequence to
drop the packets after TL1 level (SQM) instead of polling for the packets
to be sent out of RPM/CGX link.
Fixes: 5d9b976d44 ("octeontx2-af: Support fixed transmit scheduler topology")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Reviewed-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://patch.msgid.link/20240906045838.1620308-1-naveenm@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1d305abef ]
Currently, trying to set the bridge mode attribute when numvfs=0 leads to a
crash:
bridge link set dev eth2 hwmode vepa
[ 168.967392] BUG: kernel NULL pointer dereference, address: 0000000000000030
[...]
[ 168.969989] RIP: 0010:mlx5_add_flow_rules+0x1f/0x300 [mlx5_core]
[...]
[ 168.976037] Call Trace:
[ 168.976188] <TASK>
[ 168.978620] _mlx5_eswitch_set_vepa_locked+0x113/0x230 [mlx5_core]
[ 168.979074] mlx5_eswitch_set_vepa+0x7f/0xa0 [mlx5_core]
[ 168.979471] rtnl_bridge_setlink+0xe9/0x1f0
[ 168.979714] rtnetlink_rcv_msg+0x159/0x400
[ 168.980451] netlink_rcv_skb+0x54/0x100
[ 168.980675] netlink_unicast+0x241/0x360
[ 168.980918] netlink_sendmsg+0x1f6/0x430
[ 168.981162] ____sys_sendmsg+0x3bb/0x3f0
[ 168.982155] ___sys_sendmsg+0x88/0xd0
[ 168.985036] __sys_sendmsg+0x59/0xa0
[ 168.985477] do_syscall_64+0x79/0x150
[ 168.987273] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 168.987773] RIP: 0033:0x7f8f7950f917
(esw->fdb_table.legacy.vepa_fdb is null)
The bridge mode is only relevant when there are multiple functions per
port. Therefore, prevent setting and getting this setting when there are no
VFs.
Note that after this change, there are no settings to change on the PF
interface using `bridge link` when there are no VFs, so the interface no
longer appears in the `bridge link` output.
Fixes: 4b89251de0 ("net/mlx5: Support ndo bridge_setlink and getlink")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861cd9b9cb ]
Before creating a scheduling element in a NIC or E-Switch scheduler,
ensure that the requested element type is supported. If the element is
of type Transmit Scheduling Arbiter (TSAR), also verify that the
specific TSAR type is supported.
Fixes: 214baf2287 ("net/mlx5e: Support HTB offload")
Fixes: 85c5f7c920 ("net/mlx5: E-switch, Create QoS on demand")
Fixes: 0fe132eac3 ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c88146abe4 ]
Ensure the scheduling element type and TSAR type are explicitly
initialized in the QoS rate group creation.
This prevents potential issues due to default values.
Fixes: 1ae258f8b3 ("net/mlx5: E-switch, Introduce rate limiting groups API")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80bf474242 ]
Add MLX5E_400GAUI_8_400GBASE_CR8 to the extended modes
in ptys2ext_ethtool_table, since it was missing.
Fixes: 6a89737241 ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7617d62cba ]
Add MLX5E_1000BASE_T and MLX5E_100BASE_TX to the legacy
modes in ptys2legacy_ethtool_table, since they were missing.
Fixes: 665bc53969 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27717f8b17 ]
Always call igb_xdp_ring_update_tail() under __netif_tx_lock, add a comment
and lockdep assert to indicate that. This is needed to share the same TX
ring between XDP, XSK and slow paths. Furthermore, the current XDP
implementation is racy on tail updates.
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
[Kurt: Add lockdep assert and fixes tag]
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2940002b0 ]
The description of function ice_find_vsi_list_entry says:
Search VSI list map with VSI count 1
However, since the blamed commit (see Fixes below), the function no
longer checks vsi_count. This causes a problem in ice_add_vlan_internal,
where the decision to share VSI lists between filter rules relies on the
vsi_count of the found existing VSI list being 1.
The reproducing steps:
1. Have a PF and two VFs.
There will be a filter rule for VLAN 0, referring to a VSI list
containing VSIs: 0 (PF), 2 (VF#0), 3 (VF#1).
2. Add VLAN 1234 to VF#0.
ice will make the wrong decision to share the VSI list with the new
rule. The wrong behavior may not be immediately apparent, but it can
be observed with debug prints.
3. Add VLAN 1234 to VF#1.
ice will unshare the VSI list for the VLAN 1234 rule. Due to the
earlier bad decision, the newly created VSI list will contain
VSIs 0 (PF) and 3 (VF#1), instead of expected 2 (VF#0) and 3 (VF#1).
4. Try pinging a network peer over the VLAN interface on VF#0.
This fails.
Reproducer script at:
https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/test-vlan-vsi-list-confusion.sh
Commented debug trace:
https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/ice-vlan-vsi-lists-debug.txt
Patch adding the debug prints:
f8a8814623
(Unsafe, by the way. Lacks rule_lock when dumping in ice_remove_vlan.)
Michal Swiatkowski added to the explanation that the bug is caused by
reusing a VSI list created for VLAN 0. All created VFs' VSIs are added
to VLAN 0 filter. When a non-zero VLAN is created on a VF which is already
in VLAN 0 (normal case), the VSI list from VLAN 0 is reused.
It leads to a problem because all VFs (VSIs to be specific) that are
subscribed to VLAN 0 will now receive a new VLAN tag traffic. This is
one bug, another is the bug described above. Removing filters from
one VF will remove VLAN filter from the previous VF. It happens a VF is
reset. Example:
- creation of 3 VFs
- we have VSI list (used for VLAN 0) [0 (pf), 2 (vf1), 3 (vf2), 4 (vf3)]
- we are adding VLAN 100 on VF1, we are reusing the previous list
because 2 is there
- VLAN traffic works fine, but VLAN 100 tagged traffic can be received
on all VSIs from the list (for example broadcast or unicast)
- trust is turning on VF2, VF2 is resetting, all filters from VF2 are
removed; the VLAN 100 filter is also removed because 3 is on the list
- VLAN traffic to VF1 isn't working anymore, there is a need to recreate
VLAN interface to readd VLAN filter
One thing I'm not certain about is the implications for the LAG feature,
which is another caller of ice_find_vsi_list_entry. I don't have a
LAG-capable card at hand to test.
Fixes: 23ccae5ce1 ("ice: changes to the interface with the HW and FW for SRIOV_VF+LAG")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Dave Ertman <David.m.ertman@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e843cf7b34 ]
When adding a switch filter (such as a MAC or VLAN filter), it is expected
that the driver will detect the case where the filter already exists, and
return -EEXIST. This is used by calling code such as ice_vc_add_mac_addr,
and ice_vsi_add_vlan to avoid incrementing the accounting fields such as
vsi->num_vlan or vf->num_mac.
This logic works correctly for the case where only a single VSI has added a
given switch filter.
When a second VSI adds the same switch filter, the driver converts the
existing filter from an ICE_FWD_TO_VSI filter into an ICE_FWD_TO_VSI_LIST
filter. This saves switch resources, by ensuring that multiple VSIs can
re-use the same filter.
The ice_add_update_vsi_list() function is responsible for doing this
conversion. When first converting a filter from the FWD_TO_VSI into
FWD_TO_VSI_LIST, it checks if the VSI being added is the same as the
existing rule's VSI. In such a case it returns -EEXIST.
However, when the switch rule has already been converted to a
FWD_TO_VSI_LIST, the logic is different. Adding a new VSI in this case just
requires extending the VSI list entry. The logic for checking if the rule
already exists in this case returns 0 instead of -EEXIST.
This breaks the accounting logic mentioned above, so the counters for how
many MAC and VLAN filters exist for a given VF or VSI no longer accurately
reflect the actual count. This breaks other code which relies on these
counts.
In typical usage this primarily affects such filters generally shared by
multiple VSIs such as VLAN 0, or broadcast and multicast MAC addresses.
Fix this by correctly reporting -EEXIST in the case of adding the same VSI
to a switch rule already converted to ICE_FWD_TO_VSI_LIST.
Fixes: 9daf8208dd ("ice: Add support for switch filter programming")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9debb703e1 ]
After vsi setup refactor commit 6624e780a5 ("ice: split ice_vsi_setup
into smaller functions") ice_cfg_sw_lldp function which removes rx rule
directing LLDP packets to vsi is moved from ice_vsi_release to
ice_vsi_decfg function. ice_vsi_decfg is used in more cases than just in
vsi_release resulting in unnecessary removal of rx lldp packets handling
switch rule. This leads to lldp packets being dropped after a change number
of channels via ethtool.
This patch moves ice_cfg_sw_lldp function that removes rx lldp sw rule back
to ice_vsi_release function.
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Reported-by: Matěj Grégr <mgregr@netx.as>
Closes: https://lore.kernel.org/intel-wired-lan/1be45a76-90af-4813-824f-8398b69745a9@netx.as/T/#u
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 858430db28 upstream.
axienet_dma_err_handler can race with axienet_stop in the following
manner:
CPU 1 CPU 2
====================== ==================
axienet_stop()
napi_disable()
axienet_dma_stop()
axienet_dma_err_handler()
napi_disable()
axienet_dma_stop()
axienet_dma_start()
napi_enable()
cancel_work_sync()
free_irq()
Fix this by setting a flag in axienet_stop telling
axienet_dma_err_handler not to bother doing anything. I chose not to use
disable_work_sync to allow for easier backporting.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Link: https://patch.msgid.link/20240903175141.4132898-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Adjusted to apply before dmaengine support ]
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7660833d21 ]
pci_request_regions is called to apply for PCI I/O and memory resources
when the driver is initialized, Therefore, when the driver is uninstalled,
pci_release_regions should be used to release PCI I/O and memory resources
instead of pci_release_mem_regions is used to release memory reasouces
only.
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 479ffee68d ]
When disabling wifi mt7921_ipv6_addr_change() is called as a notifier.
At this point mvif->phy is already NULL so we cannot use it here.
Signed-off-by: Bert Karwatzki <spasswolf@web.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240812104542.80760-1-spasswolf@web.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de7a670f8d ]
When the vsc73xx mdio bus work properly, the generic autonegotiation
configuration works well.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a039eeb71 ]
`ip_hdr(skb)->ihl << 2` is the same as `ip_hdrlen(skb)`
Therefore, we should use a well-defined function not a bit shift
to find the header length.
It also compresses two lines to a single line.
Signed-off-by: Moon Yeounsu <yyyynoom@gmail.com>
Reviewed-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67927a1b25 ]
Apart from the standard "configurations", "interfaces" and "alternate
interface settings" in USB, iOS devices also have a notion of
"modes". In different modes, the device exposes a different set of
available configurations.
Depending on the iOS version, and depending on the current mode, the
length and contents of the carrier state control message differs:
* 1 byte (seen on iOS 4.2.1, 8.4):
* 03: carrier off (mode 0)
* 04: carrier on (mode 0)
* 3 bytes (seen on iOS 10.3.4, 15.7.6):
* 03 03 03: carrier off (mode 0)
* 04 04 03: carrier on (mode 0)
* 4 bytes (seen on iOS 16.5, 17.6):
* 03 03 03 00: carrier off (mode 0)
* 04 03 03 00: carrier off (mode 1)
* 06 03 03 00: carrier off (mode 4)
* 04 04 03 04: carrier on (mode 0 and 1)
* 06 04 03 04: carrier on (mode 4)
Before this change, the driver always used the first byte of the
response to determine carrier state.
From this larger sample, the first byte seems to indicate the number of
available USB configurations in the current mode (with the exception of
the default mode 0), and in some cases (namely mode 1 and 4) does not
correlate with the carrier state.
Previous logic erroneously counted `04 03 03 00` as "carrier on" and
`06 04 03 04` as "carrier off" on iOS versions that support mode 1 and
mode 4 respectively.
Only modes 0, 1 and 4 expose the USB Ethernet interfaces necessary for
the ipheth driver.
Check the second byte of the control message where possible, and fall
back to checking the first byte on older iOS versions.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74efed51e0 ]
RX callbacks can fail for multiple reasons:
* Payload too short
* Payload formatted incorrecly (e.g. bad NCM framing)
* Lack of memory
None of these should cause the driver to seize up.
Make such failures non-critical and continue processing further
incoming URBs.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94d7eeb6c0 ]
On iPhone 15 Pro Max one can observe periodic URBs with no payload
on the "bulk in" (RX) endpoint. These don't seem to do anything
meaningful. Reproduced on iOS 17.5.1 and 17.6.
This behaviour isn't observed on iPhone 11 on the same iOS version. The
nature of these zero-length URBs is so far unknown.
Drop RX URBs with no payload.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 655b46d7a3 ]
Rx URB length was already checked in ipheth_rcvbulk_callback_legacy()
and ipheth_rcvbulk_callback_ncm(), depending on the current mode.
The check in ipheth_rcvbulk_callback() was thus mostly a duplicate.
The only place in ipheth_rcvbulk_callback() where we care about the URB
length is for the initial control frame. These frames are always 4 bytes
long. This has been checked as far back as iOS 4.2.1 on iPhone 3G.
Remove the extraneous URB length check. For control frames, check for
the specific 4-byte length instead.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24436be590 ]
This patch tries to works around erratum DS80000789E 6 of the
mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old, already processed CAN frames or new, incompletely written CAN
frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp [1] of the last
valid received CAN frame and compare against the timestamp of every
received CAN frame. If an old CAN frame is detected, abort the
iteration and mark the number of valid CAN frames as processed in the
chip by incrementing the FIFO's tail index.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames [2] are not recognized but then processed. These CAN frames
have the correct data and time stamps, but the DLC has not yet been
updated.
[1] As the raw timestamp overflows every 107 seconds (at the usual
clock rate of 40 MHz) convert it to nanoseconds with the
timecounter framework and use this to detect stale CAN frames.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com [2]
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e793c724b4 ]
The mcp251xfd chip is configured to provide a timestamp with each
received and transmitted CAN frame. The timestamp is derived from the
internal free-running timer, which can also be read from the TBC
register via SPI. The timer is 32 bits wide and is clocked by the
external oscillator (typically 20 or 40 MHz).
To avoid confusion, we call this timestamp "timestamp_raw" or "ts_raw"
for short.
Using the timecounter framework, the "ts_raw" is converted to 64 bit
nanoseconds since the epoch. This is what we call "timestamp".
This is a preparation for the next patches which use the "timestamp"
to work around a bug where so far only the "ts_raw" is used.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85505e5856 ]
This is a preparatory patch to work around erratum DS80000789E 6 of
the mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
When handling the RX interrupt, the driver iterates over all pending
FIFOs (which are implemented as ring buffers in hardware) and reads
the FIFO header index from the RX FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN frames that were already processed, or new, incompletely
written CAN frames to be (re-)processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_rx_ring_update() with mcp251xfd_get_rx_len().
The mcp251xfd_handle_rxif_ring() function reads the received CAN
frames from the chip, iterates over them and pushes them into the
network stack. Prepare that the iteration can be stopped if an old CAN
frame is detected. The actual code to detect old or incomplete frames
and abort will be added in the next patch.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d49184b7b5 ]
This is a preparation patch.
Sending the UINC messages followed by incrementing the tail pointer
will be called in more than one place in upcoming patches, so factor
this out into a separate function.
Also make mcp251xfd_handle_rxif_ring_uinc() safe to be called with a
"len" of 0.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ba54b1a276 upstream.
Refactoring of the field get conversion introduced a regression in the
legacy Wake On Lan from a magic packet with i219 devices. Rx address
copied not correctly from MAC to PHY with FIELD_GET macro.
Fixes: b9a4525450 ("intel: legacy: field get conversion")
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Florian Larysch <fl@n621.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5876b088b ]
ipheth_sndbulk_callback() can submit carrier_work
as a part of its error handling. That means that
the driver must make sure that the work is cancelled
after it has made sure that no more URB can terminate
with an error condition.
Hence the order of actions in ipheth_close() needs
to be inverted.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555a05d84c ]
The dpaa-eth driver is written for PowerPC and Arm SoCs which have 1-24
CPUs. It depends on CONFIG_NR_CPUS having a reasonably small value in
Kconfig. Otherwise, there are 2 functions which allocate on-stack arrays
of NR_CPUS elements, and these can quickly explode in size, leading to
warnings such as:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:3280:12: warning:
stack frame size (16664) exceeds limit (2048) in 'dpaa_eth_probe' [-Wframe-larger-than]
The problem is twofold:
- Reducing the array size to the boot-time num_possible_cpus() (rather
than the compile-time NR_CPUS) creates a variable-length array,
which should be avoided in the Linux kernel.
- Using NR_CPUS as an array size makes the driver blow up in stack
consumption with generic, as opposed to hand-crafted, .config files.
A simple solution is to use dynamic allocation for num_possible_cpus()
elements (aka a small number determined at runtime).
Link: https://lore.kernel.org/all/202406261920.l5pzM1rj-lkp@intel.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://patch.msgid.link/20240713225336.1746343-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adc539784c ]
Right now it's possible to hit NULL pointer dereference in
rtw_rx_fill_rx_status on hw object and/or its fields because
initialization routine can start getting USB replies before
rtw_dev is fully setup.
The stack trace looks like this:
rtw_rx_fill_rx_status
rtw8821c_query_rx_desc
rtw_usb_rx_handler
...
queue_work
rtw_usb_read_port_complete
...
usb_submit_urb
rtw_usb_rx_resubmit
rtw_usb_init_rx
rtw_usb_probe
So while we do the async stuff rtw_usb_probe continues and calls
rtw_register_hw, which does all kinds of initialization (e.g.
via ieee80211_register_hw) that rtw_rx_fill_rx_status relies on.
Fix this by moving the first usb_submit_urb after everything
is set up.
For me, this bug manifested as:
[ 8.893177] rtw_8821cu 1-1:1.2: band wrong, packet dropped
[ 8.910904] rtw_8821cu 1-1:1.2: hw->conf.chandef.chan NULL in rtw_rx_fill_rx_status
because I'm using Larry's backport of rtw88 driver with the NULL
checks in rtw_rx_fill_rx_status.
Link: https://lore.kernel.org/linux-wireless/CA+shoWQ7P49jhQasofDcTdQhiuarPTjYEDa--NiVVx494WcuQw@mail.gmail.com/
Signed-off-by: Marcin Ślusarz <mslusarz@renau.com>
Cc: Tim K <tpkuester@gmail.com>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240528110246.477321-1-marcin.slusarz@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8487b4af59 ]
generic_ocp_write() asks the parameter "size" must be 4 bytes align.
Therefore, write the bp would fail, if the mac->bp_num is odd. Align the
size to 4 for fixing it. The way may write an extra bp, but the
rtl8152_is_fw_mac_ok() makes sure the value must be 0 for the bp whose
index is more than mac->bp_num. That is, there is no influence for the
firmware.
Besides, I check the return value of generic_ocp_write() to make sure
everything is correct.
Fixes: e5c266a611 ("r8152: set bp in bulk")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20240903063333.4502-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bab8eb0dd4 ]
The driver generates a random MAC once on load
and uses it over and over, including on two devices
needing a random MAC at the same time.
Jakub suggested revamping the driver to the modern
API for setting a random MAC rather than fixing
the old stuff.
The bug is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://patch.msgid.link/20240829175201.670718-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04c7e14e5b ]
After XDP configuration is completed, we bring the interface up
unconditionally, regardless of its state before the call to .ndo_bpf().
Preserve the information whether the interface had to be brought down and
later bring it up only in such case.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2504b84057 ]
The main threat to data consistency in ice_xdp() is a possible asynchronous
PF reset. It can be triggered by a user or by TX timeout handler.
XDP setup and PF reset code access the same resources in the following
sections:
* ice_vsi_close() in ice_prepare_for_reset() - already rtnl-locked
* ice_vsi_rebuild() for the PF VSI - not protected
* ice_vsi_open() - already rtnl-locked
With an unfortunate timing, such accesses can result in a crash such as the
one below:
[ +1.999878] ice 0000:b1:00.0: Registered XDP mem model MEM_TYPE_XSK_BUFF_POOL on Rx ring 14
[ +2.002992] ice 0000:b1:00.0: Registered XDP mem model MEM_TYPE_XSK_BUFF_POOL on Rx ring 18
[Mar15 18:17] ice 0000:b1:00.0 ens801f0np0: NETDEV WATCHDOG: CPU: 38: transmit queue 14 timed out 80692736 ms
[ +0.000093] ice 0000:b1:00.0 ens801f0np0: tx_timeout: VSI_num: 6, Q 14, NTC: 0x0, HW_HEAD: 0x0, NTU: 0x0, INT: 0x4000001
[ +0.000012] ice 0000:b1:00.0 ens801f0np0: tx_timeout recovery level 1, txqueue 14
[ +0.394718] ice 0000:b1:00.0: PTP reset successful
[ +0.006184] BUG: kernel NULL pointer dereference, address: 0000000000000098
[ +0.000045] #PF: supervisor read access in kernel mode
[ +0.000023] #PF: error_code(0x0000) - not-present page
[ +0.000023] PGD 0 P4D 0
[ +0.000018] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ +0.000023] CPU: 38 PID: 7540 Comm: kworker/38:1 Not tainted 6.8.0-rc7 #1
[ +0.000031] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0014.082620210524 08/26/2021
[ +0.000036] Workqueue: ice ice_service_task [ice]
[ +0.000183] RIP: 0010:ice_clean_tx_ring+0xa/0xd0 [ice]
[...]
[ +0.000013] Call Trace:
[ +0.000016] <TASK>
[ +0.000014] ? __die+0x1f/0x70
[ +0.000029] ? page_fault_oops+0x171/0x4f0
[ +0.000029] ? schedule+0x3b/0xd0
[ +0.000027] ? exc_page_fault+0x7b/0x180
[ +0.000022] ? asm_exc_page_fault+0x22/0x30
[ +0.000031] ? ice_clean_tx_ring+0xa/0xd0 [ice]
[ +0.000194] ice_free_tx_ring+0xe/0x60 [ice]
[ +0.000186] ice_destroy_xdp_rings+0x157/0x310 [ice]
[ +0.000151] ice_vsi_decfg+0x53/0xe0 [ice]
[ +0.000180] ice_vsi_rebuild+0x239/0x540 [ice]
[ +0.000186] ice_vsi_rebuild_by_type+0x76/0x180 [ice]
[ +0.000145] ice_rebuild+0x18c/0x840 [ice]
[ +0.000145] ? delay_tsc+0x4a/0xc0
[ +0.000022] ? delay_tsc+0x92/0xc0
[ +0.000020] ice_do_reset+0x140/0x180 [ice]
[ +0.000886] ice_service_task+0x404/0x1030 [ice]
[ +0.000824] process_one_work+0x171/0x340
[ +0.000685] worker_thread+0x277/0x3a0
[ +0.000675] ? preempt_count_add+0x6a/0xa0
[ +0.000677] ? _raw_spin_lock_irqsave+0x23/0x50
[ +0.000679] ? __pfx_worker_thread+0x10/0x10
[ +0.000653] kthread+0xf0/0x120
[ +0.000635] ? __pfx_kthread+0x10/0x10
[ +0.000616] ret_from_fork+0x2d/0x50
[ +0.000612] ? __pfx_kthread+0x10/0x10
[ +0.000604] ret_from_fork_asm+0x1b/0x30
[ +0.000604] </TASK>
The previous way of handling this through returning -EBUSY is not viable,
particularly when destroying AF_XDP socket, because the kernel proceeds
with removal anyway.
There is plenty of code between those calls and there is no need to create
a large critical section that covers all of them, same as there is no need
to protect ice_vsi_rebuild() with rtnl_lock().
Add xdp_state_lock mutex to protect ice_vsi_rebuild() and ice_xdp().
Leaving unprotected sections in between would result in two states that
have to be considered:
1. when the VSI is closed, but not yet rebuild
2. when VSI is already rebuild, but not yet open
The latter case is actually already handled through !netif_running() case,
we just need to adjust flag checking a little. The former one is not as
trivial, because between ice_vsi_close() and ice_vsi_rebuild(), a lot of
hardware interaction happens, this can make adding/deleting rings exit
with an error. Luckily, VSI rebuild is pending and can apply new
configuration for us in a managed fashion.
Therefore, add an additional VSI state flag ICE_VSI_REBUILD_PENDING to
indicate that ice_xdp() can just hot-swap the program.
Also, as ice_vsi_rebuild() flow is touched in this patch, make it more
consistent by deconfiguring VSI when coalesce allocation fails.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2560db6ede ]
The call of of_get_child_by_name() will cause refcount incremented
for leds, if it succeeds, it should call of_node_put() to decrease
it, fix it.
Fixes: 01e5b728e9 ("net: phy: Add a binding for PHY LEDs")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240830022025.610844-1-ruanjinjie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef4a99a016 ]
Call rtnl_unlock() on this error path, before returning.
Fixes: bc23aa949a ("igc: Add pcie error handler support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd885d90c0 ]
Kvaser's PCIe cards uses the KCAN FPGA IP block which has dual 4K
buffers for incoming messages shared by all (currently up to eight)
channels. While the driver processes messages in one buffer, new
incoming messages are stored in the other and so on.
The design of KCAN is such that a buffer must be fully read and then
released. Releasing a buffer will make the FPGA switch buffers. If the
other buffer contains at least one incoming message the FPGA will also
instantly issue a new interrupt, if not the interrupt will be issued
after receiving the first new message.
With IRQx interrupts, it takes a little time for the interrupt to
happen, enough for any previous ISR call to do it's business and
return, but MSI interrupts are way faster so this time is reduced to
almost nothing.
So with MSI, releasing the buffer HAS to be the very last action of
the ISR before returning, otherwise the new interrupt might be
"masked" by the kernel because the previous ISR call hasn't returned.
And the interrupts are edge-triggered so we cannot loose one, or the
ping-pong reading process will stop.
This is why this patch modifies the driver to use a single write to
the SRB_CMD register before returning.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20240830153113.2081440-1-martin.jocic@kvaser.com
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48f827d4f4 ]
A new interrupt is triggered by resetting the DMA RX buffers.
Since MSI interrupts are faster than legacy interrupts, the reset
of the DMA buffers must be moved to the very end of the ISR,
otherwise a new MSI interrupt will be masked by the current one.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240620181320.235465-2-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c0 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf88a6ba7 ]
Rename the variable name board_irq in the ISR to pci_irq to
be more specific and to match the macro by which it is read.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-7-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c0 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d186697c ]
The code speaks for itself.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-4-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c0 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac765219c2 ]
This check is already done at the creation of the net devices in
kvaser_pciefd_setup_can_ctrls called from kvaser_pciefd_probe.
If it fails, the driver won't load, so there should be no need to
repeat the check inside the ISR. The number of channels is read
from the FPGA and should be trusted.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-3-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c0 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d11a676342 ]
Ethtool callbacks can be executed while reset is in progress and try to
access deleted resources, e.g. getting coalesce settings can result in a
NULL pointer dereference seen below.
Reproduction steps:
Once the driver is fully initialized, trigger reset:
# echo 1 > /sys/class/net/<interface>/device/reset
when reset is in progress try to get coalesce settings using ethtool:
# ethtool -c <interface>
BUG: kernel NULL pointer dereference, address: 0000000000000020
PGD 0 P4D 0
Oops: Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 11 PID: 19713 Comm: ethtool Tainted: G S 6.10.0-rc7+ #7
RIP: 0010:ice_get_q_coalesce+0x2e/0xa0 [ice]
RSP: 0018:ffffbab1e9bcf6a8 EFLAGS: 00010206
RAX: 000000000000000c RBX: ffff94512305b028 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9451c3f2e588 RDI: ffff9451c3f2e588
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: ffff9451c3f2e580 R11: 000000000000001f R12: ffff945121fa9000
R13: ffffbab1e9bcf760 R14: 0000000000000013 R15: ffffffff9e65dd40
FS: 00007faee5fbe740(0000) GS:ffff94546fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000020 CR3: 0000000106c2e005 CR4: 00000000001706f0
Call Trace:
<TASK>
ice_get_coalesce+0x17/0x30 [ice]
coalesce_prepare_data+0x61/0x80
ethnl_default_doit+0xde/0x340
genl_family_rcv_msg_doit+0xf2/0x150
genl_rcv_msg+0x1b3/0x2c0
netlink_rcv_skb+0x5b/0x110
genl_rcv+0x28/0x40
netlink_unicast+0x19c/0x290
netlink_sendmsg+0x222/0x490
__sys_sendto+0x1df/0x1f0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x82/0x160
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7faee60d8e27
Calling netif_device_detach() before reset makes the net core not call
the driver when ethtool command is issued, the attempt to execute an
ethtool command during reset will result in the following message:
netlink error: No such device
instead of NULL pointer dereference. Once reset is done and
ice_rebuild() is executing, the netif_device_attach() is called to allow
for ethtool operations to occur again in a safe manner.
Fixes: fcea6f3da5 ("ice: Add stats and ethtool support")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba8cf80724 ]
82580 NICs have a hardware bug that makes it
necessary to write into the TSICR (TimeSync Interrupt Cause) register
to clear it:
https://lore.kernel.org/all/CDCB8BE0.1EC2C%25matthew.vick@intel.com/
Add a conditional so only for 82580 we write into the TSICR register,
so we don't risk losing events for other models.
Without this change, when running ptp4l with an Intel 82580 card,
I get the following output:
> timed out while polling for tx timestamp increasing tx_timestamp_timeout or
> increasing kworker priority may correct this issue, but a driver bug likely
> causes it
This goes away with this change.
This (partially) reverts commit ee14cc9ea1 ("igb: Fix missing time sync events").
Fixes: ee14cc9ea1 ("igb: Fix missing time sync events")
Closes: https://lore.kernel.org/intel-wired-lan/CAN0jFd1kO0MMtOh8N2Ztxn6f7vvDKp2h507sMryobkBKe=xk=w@mail.gmail.com/
Tested-by: Daiwei Li <daiweili@google.com>
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Daiwei Li <daiweili@google.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50ea5449c5 ]
If the ring (rx, tx) and/or coalescing parameters (rx-frames-irq,
tx-frames-irq) have been configured while the interface was in CAN-CC
mode, but the interface is brought up in CAN-FD mode, the ring
parameters might be too big.
Use the default CAN-FD values in this case.
Fixes: 9263c2e92b ("can: mcp251xfd: ring: add support for runtime configurable RX/TX ring parameters")
Link: https://lore.kernel.org/all/20240805-mcp251xfd-fix-ringconfig-v1-1-72086f0ca5ee@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
