commit f9244fb55f upstream.
When removing a netfront device directly after a suspend/resume cycle
it might happen that the queues have not been setup again, causing a
crash during the attempt to stop the queues another time.
Fix that by checking the queues are existing before trying to stop
them.
This is XSA-465 / CVE-2024-53240.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: d50b7914fa ("xen-netfront: Fix NULL sring after live migration")
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a0c28efee upstream.
The use-after-free is actually in rswitch_tx_free(), which is inlined in
rswitch_poll(). Since `skb` and `gq->skbs[gq->dirty]` are in fact the
same pointer, the skb is first freed using dev_kfree_skb_any(), then the
value in skb->len is used to update the interface statistics.
Let's move around the instructions to use skb->len before the skb is
freed.
This bug is trivial to reproduce using KFENCE. It will trigger a splat
every few packets. A simple ARP request or ICMP echo request is enough.
Fixes: 271e015b91 ("net: rswitch: Add unmap_addrs instead of dma address in each desc")
Signed-off-by: Radu Rendec <rrendec@redhat.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20240702210838.2703228-1-rrendec@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5af53577c6 ]
Commit 8d7ae22ae9 ("net: dsa: microchip: KSZ9477 register regmap
alignment to 32 bit boundaries") fixed an issue whereby regmap_reg_range
did not allow writes as 32 bit words to KSZ9477 PHY registers, this fix
for KSZ9896 is adapted from there as the same errata is present in
KSZ9896C as "Module 5: Certain PHY registers must be written as pairs
instead of singly" the explanation below is likewise taken from this
commit.
The commit provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accessed as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9896 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Fixes: 5c844d57aa ("net: dsa: microchip: fix writes to phy registers >= 0x10")
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Link: https://patch.msgid.link/20241211092932.26881-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb9e6039c3 ]
MPIC.PIS must be set per phy interface type.
MPIC.LSC must be set per speed.
Do that strictly per datasheet, instead of hardcoding MPIC.PIS to GMII.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241211053012.368914-1-nikita.yoush@cogentembedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9871284458 ]
Similar to bonding driver, add NETIF_F_GSO_ENCAP_ALL to TEAM_VLAN_FEATURES
in order to support slave devices which propagate NETIF_F_GSO_UDP_TUNNEL &
NETIF_F_GSO_UDP_TUNNEL_CSUM as vlan_features.
Fixes: 3625920b62 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-5-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77b11c8bf3 ]
Drivers like mlx5 expose NIC's vlan_features such as
NETIF_F_GSO_UDP_TUNNEL & NETIF_F_GSO_UDP_TUNNEL_CSUM which are
later not propagated when the underlying devices are bonded and
a vlan device created on top of the bond.
Right now, the more cumbersome workaround for this is to create
the vlan on top of the mlx5 and then enslave the vlan devices
to a bond.
To fix this, add NETIF_F_GSO_ENCAP_ALL to BOND_VLAN_FEATURES
such that bond_compute_features() can probe and propagate the
vlan_features from the slave devices up to the vlan device.
Given the following bond:
# ethtool -i enp2s0f{0,1}np{0,1}
driver: mlx5_core
[...]
# ethtool -k enp2s0f0np0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k enp2s0f1np1 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k bond0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Before:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: off [requested on]
tx-udp_tnl-csum-segmentation: off [requested on]
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
After:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Various users have run into this reporting performance issues when
configuring Cilium in vxlan tunneling mode and having the combination
of bond & vlan for the core devices connecting the Kubernetes cluster
to the outside world.
Fixes: a9b3ace44c ("bonding: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-3-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acfcdb78d5 ]
With this port schedule:
tc qdisc replace dev $send_if parent root handle 100 taprio \
num_tc 8 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
map 0 1 2 3 4 5 6 7 \
base-time 0 cycle-time 10000 \
sched-entry S 01 1250 \
sched-entry S 02 1250 \
sched-entry S 04 1250 \
sched-entry S 08 1250 \
sched-entry S 10 1250 \
sched-entry S 20 1250 \
sched-entry S 40 1250 \
sched-entry S 80 1250 \
flags 2
ptp4l would fail to take TX timestamps of Pdelay_Resp messages like this:
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
ptp4l[4134.168]: port 2: send peer delay response failed
It turns out that the driver can't take their TX timestamps because it
can't transmit them in the first place. And there's nothing special
about the Pdelay_Resp packets - they're just regular 68 byte packets.
But with this taprio configuration, the switch would refuse to send even
the ETH_ZLEN minimum packet size.
This should have definitely not been the case. When applying the taprio
config, the driver prints:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
and thus, everything under 132 bytes - ETH_FCS_LEN should have been sent
without problems. Yet it's not.
For the forwarding path, the configuration is fine, yet packets injected
from Linux get stuck with this schedule no matter what.
The first hint that the static guard bands are the cause of the problem
is that reverting Michael Walle's commit 297c4de6f7 ("net: dsa: felix:
re-enable TAS guard band mode") made things work. It must be that the
guard bands are calculated incorrectly.
I remembered that there is a magic constant in the driver, set to 33 ns
for no logical reason other than experimentation, which says "never let
the static guard bands get so large as to leave less than this amount of
remaining space in the time slot, because the queue system will refuse
to schedule packets otherwise, and they will get stuck". I had a hunch
that my previous experimentally-determined value was only good for
packets coming from the forwarding path, and that the CPU injection path
needed more.
I came to the new value of 35 ns through binary search, after seeing
that with 544 ns (the bit time required to send the Pdelay_Resp packet
at gigabit) it works. Again, this is purely experimental, there's no
logic and the manual doesn't say anything.
The new driver prints for this schedule look like this:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
So yes, the maximum MTU is now even smaller by 1 byte than before.
This is maybe counter-intuitive, but makes more sense with a diagram of
one time slot.
Before:
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<----><---------------------------------------------->
33 ns 1217 ns static guard band
useful
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<-----><--------------------------------------------->
35 ns 1215 ns static guard band
useful
The static guard band implemented by this switch hardware directly
determines the maximum allowable MTU for that traffic class. The larger
it is, the earlier the switch will stop scheduling frames for
transmission, because otherwise they might overrun the gate close time
(and avoiding that is the entire purpose of Michael's patch).
So, we now have guard bands smaller by 2 ns, thus, in this particular
case, we lose a byte of the maximum MTU.
Fixes: 11afdc6526 ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20241210132640.3426788-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dd002f200 ]
Currently the stop routine of rswitch driver does not immediately
prevent hardware from continuing to update descriptors and requesting
interrupts.
It can happen that when rswitch_stop() executes the masking of
interrupts from the queues of the port being closed, napi poll for
that port is already scheduled or running on a different CPU. When
execution of this napi poll completes, it will unmask the interrupts.
And unmasked interrupt can fire after rswitch_stop() returns from
napi_disable() call. Then, the handler won't mask it, because
napi_schedule_prep() will return false, and interrupt storm will
happen.
This can't be fixed by making rswitch_stop() call napi_disable() before
masking interrupts. In this case, the interrupt storm will happen if
interrupt fires between napi_disable() and masking.
Fix this by checking for priv->opened_ports bit when unmasking
interrupts after napi poll. For that to be consistent, move
priv->opened_ports changes into spinlock-protected areas, and reorder
other operations in rswitch_open() and rswitch_stop() accordingly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Link: https://patch.msgid.link/20241209113204.175015-1-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66b7e9f85b ]
The device tree node saved in the rswitch_device structure is used at
several driver locations. So passing this node to of_node_put() after
the first use is wrong.
Move of_node_put() for this node to exit paths.
Fixes: b46f1e5793 ("net: renesas: rswitch: Simplify struct phy * handling")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-5-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb617328ba ]
If error path is taken while filling descriptor for a frame, skb
pointer is left in the entry. Later, on the ring entry reuse, the
same entry could be used as a part of a multi-descriptor frame,
and skb for that new frame could be stored in a different entry.
Then, the stale pointer will reach the completion routine, and passed
to the release operation.
Fix that by clearing the saved skb pointer at the error path.
Fixes: d2c96b9d5f ("net: rswitch: Add jumbo frames handling for TX")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-4-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c9547e6cc ]
If hardware is already transmitting, it can start handling the
descriptor being written to immediately after it observes updated DT
field, before the queue is kicked by a write to GWTRC.
If the start_xmit() execution is preempted at unfortunate moment, this
transmission can complete, and interrupt handled, before gq->cur gets
updated. With the current implementation of completion, this will cause
the last entry not completed.
Fix that by changing completion loop to check DT values directly, instead
of depending on gq->cur.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-3-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2c96b9d5f ]
If the driver would like to transmit a jumbo frame like 2KiB or more,
it should be split into multiple queues. In the near future, to support
this, add handling specific descriptor types F{START,MID,END}. However,
such jumbo frames will not happen yet because the maximum MTU size is
still default for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 0c9547e6cc ("net: renesas: rswitch: fix race window between tx start and complete")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcff581ee4 ]
If the driver would like to transmit a jumbo frame like 2KiB or more,
it should be split into multiple queues. In the near future, to support
this, add a setting ext descriptor function to improve code readability.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 0c9547e6cc ("net: renesas: rswitch: fix race window between tx start and complete")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 271e015b91 ]
If the driver would like to transmit a jumbo frame like 2KiB or more,
it should be split into multiple queues. In the near future, to support
this, add unmap_addrs array to unmap dma mapping address instead of dma
address in each TX descriptor because the descriptors may not have
the top dma address.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 0c9547e6cc ("net: renesas: rswitch: fix race window between tx start and complete")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a203cb516 ]
If this hardware receives a jumbo frame like 2KiB or more, it will be
split into multiple queues. In the near future, to support this, use
build_skb() instead of netdev_alloc_skb_ip_align().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 0c9547e6cc ("net: renesas: rswitch: fix race window between tx start and complete")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8857034184 ]
Array index should not be negative, so use unsigned int for
descriptors related array index.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 0c9547e6cc ("net: renesas: rswitch: fix race window between tx start and complete")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e0022390 ]
Drop unused argument and return value of rswitch_tx_free() to
simplify the code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 0c9547e6cc ("net: renesas: rswitch: fix race window between tx start and complete")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit becc6399ce ]
The module parameter qcaspi_pluggable controls if QCA7000 signature
should be checked at driver probe (current default) or not. Unfortunately
this could fail in case the chip is temporary in reset, which isn't under
total control by the Linux host. So disable this check per default
in order to avoid unexpected probe failures.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dba406fac ]
Storing the maximum clock speed in module parameter qcaspi_clkspeed
has the unintended side effect that the first probed instance
defines the value for all other instances. Fix this issue by storing
it in max_speed_hz of the relevant SPI device.
This fix keeps the priority of the speed parameter (module parameter,
device tree property, driver default). Btw this uses the opportunity
to get the rid of the unused member clkspeed.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 356983f569 ]
t4_set_vf_mac_acl() uses pf to set mac addr, but t4vf_get_vf_mac_acl()
uses port number to get mac addr, this leads to error when an attempt
to set MAC address on VF's of PF2 and PF3.
This patch fixes the issue by using port number to set mac address.
Fixes: e0cdac65ba ("cxgb4vf: configure ports accessible by the VF")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241206062014.49414-1-anumula@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddd7ba0060 ]
On port initialization, we configure the maximum frame length accepted
by the receive module associated with the port. This value is currently
written to the MAX_LEN field of the DEV10G_MAC_ENA_CFG register, when in
fact, it should be written to the DEV10G_MAC_MAXLEN_CFG register. Fix
this.
Fixes: 946e7fd505 ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f004f2e535 ]
The FDMA handler is responsible for scheduling a NAPI poll, which will
eventually fetch RX packets from the FDMA queue. Currently, the FDMA
handler is run in a threaded context. For some reason, this kills
performance. Admittedly, I did not do a thorough investigation to see
exactly what causes the issue, however, I noticed that in the other
driver utilizing the same FDMA engine, we run the FDMA handler in hard
IRQ context.
Fix this performance issue, by running the FDMA handler in hard IRQ
context, not deferring any work to a thread.
Prior to this change, the RX UDP performance was:
Interval Transfer Bitrate Jitter
0.00-10.20 sec 44.6 MBytes 36.7 Mbits/sec 0.027 ms
After this change, the rx UDP performance is:
Interval Transfer Bitrate Jitter
0.00-9.12 sec 1.01 GBytes 953 Mbits/sec 0.020 ms
Fixes: 10615907e9 ("net: sparx5: switchdev: adding frame DMA functionality")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43a4166349 ]
An unsupported RX filter will leave the port with TX timestamping still
applied as per the new request, rather than the old setting. When
parsing the tx_type, don't apply it just yet, but delay that until after
we've parsed the rx_filter as well (and potentially returned -ERANGE for
that).
Similarly, copy_to_user() may fail, which is a rare occurrence, but
should still be treated by unwinding what was done.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-6-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b454abfab5 ]
The Felix DSA driver presents unique challenges that make the simplistic
ocelot PTP TX timestamping procedure unreliable: any transmitted packet
may be lost in hardware before it ever leaves our local system.
This may happen because there is congestion on the DSA conduit, the
switch CPU port or even user port (Qdiscs like taprio may delay packets
indefinitely by design).
The technical problem is that the kernel, i.e. ocelot_port_add_txtstamp_skb(),
runs out of timestamp IDs eventually, because it never detects that
packets are lost, and keeps the IDs of the lost packets on hold
indefinitely. The manifestation of the issue once the entire timestamp
ID range becomes busy looks like this in dmesg:
mscc_felix 0000:00:00.5: port 0 delivering skb without TX timestamp
mscc_felix 0000:00:00.5: port 1 delivering skb without TX timestamp
At the surface level, we need a timeout timer so that the kernel knows a
timestamp ID is available again. But there is a deeper problem with the
implementation, which is the monotonically increasing ocelot_port->ts_id.
In the presence of packet loss, it will be impossible to detect that and
reuse one of the holes created in the range of free timestamp IDs.
What we actually need is a bitmap of 63 timestamp IDs tracking which one
is available. That is able to use up holes caused by packet loss, but
also gives us a unique opportunity to not implement an actual timer_list
for the timeout timer (very complicated in terms of locking).
We could only declare a timestamp ID stale on demand (lazily), aka when
there's no other timestamp ID available. There are pros and cons to this
approach: the implementation is much more simple than per-packet timers
would be, but most of the stale packets would be quasi-leaked - not
really leaked, but blocked in driver memory, since this algorithm sees
no reason to free them.
An improved technique would be to check for stale timestamp IDs every
time we allocate a new one. Assuming a constant flux of PTP packets,
this avoids stale packets being blocked in memory, but of course,
packets lost at the end of the flux are still blocked until the flux
resumes (nobody left to kick them out).
Since implementing per-packet timers is way too complicated, this should
be good enough.
Testing procedure:
Persistently block traffic class 5 and try to run PTP on it:
$ tc qdisc replace dev swp3 parent root taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0xdf 100000 flags 0x2
[ 126.948141] mscc_felix 0000:00:00.5: port 3 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
$ ptp4l -i swp3 -2 -P -m --socket_priority 5 --fault_reset_interval ASAP --logSyncInterval -3
ptp4l[70.351]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.354]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.358]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 70.394583] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[70.406]: timed out while polling for tx timestamp
ptp4l[70.406]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[70.406]: port 1 (swp3): send peer delay response failed
ptp4l[70.407]: port 1 (swp3): clearing fault immediately
ptp4l[70.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 71.394858] mscc_felix 0000:00:00.5: port 3 timestamp id 1
ptp4l[71.400]: timed out while polling for tx timestamp
ptp4l[71.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[71.401]: port 1 (swp3): send peer delay response failed
ptp4l[71.401]: port 1 (swp3): clearing fault immediately
[ 72.393616] mscc_felix 0000:00:00.5: port 3 timestamp id 2
ptp4l[72.401]: timed out while polling for tx timestamp
ptp4l[72.402]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[72.402]: port 1 (swp3): send peer delay response failed
ptp4l[72.402]: port 1 (swp3): clearing fault immediately
ptp4l[72.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 73.395291] mscc_felix 0000:00:00.5: port 3 timestamp id 3
ptp4l[73.400]: timed out while polling for tx timestamp
ptp4l[73.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[73.400]: port 1 (swp3): send peer delay response failed
ptp4l[73.400]: port 1 (swp3): clearing fault immediately
[ 74.394282] mscc_felix 0000:00:00.5: port 3 timestamp id 4
ptp4l[74.400]: timed out while polling for tx timestamp
ptp4l[74.401]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[74.401]: port 1 (swp3): send peer delay response failed
ptp4l[74.401]: port 1 (swp3): clearing fault immediately
ptp4l[74.953]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 75.396830] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 75.405760] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[75.410]: timed out while polling for tx timestamp
ptp4l[75.411]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[75.411]: port 1 (swp3): send peer delay response failed
ptp4l[75.411]: port 1 (swp3): clearing fault immediately
(...)
Remove the blocking condition and see that the port recovers:
$ same tc command as above, but use "sched-entry S 0xff" instead
$ same ptp4l command as above
ptp4l[99.489]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.490]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.492]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 100.403768] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 100.412545] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 1 which seems lost
[ 100.421283] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 2 which seems lost
[ 100.430015] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 3 which seems lost
[ 100.438744] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 4 which seems lost
[ 100.447470] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 100.505919] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[100.963]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 101.405077] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 101.507953] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.405405] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.509391] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.406003] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.510011] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.405601] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.510624] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[104.965]: selected best master clock d858d7.fffe.00ca6d
ptp4l[104.966]: port 1 (swp3): assuming the grand master role
ptp4l[104.967]: port 1 (swp3): LISTENING to GRAND_MASTER on RS_GRAND_MASTER
[ 105.106201] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.232420] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.359001] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.405500] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.485356] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.511220] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.610938] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.737237] mscc_felix 0000:00:00.5: port 3 timestamp id 0
(...)
Notice that in this new usage pattern, a non-congested port should
basically use timestamp ID 0 all the time, progressing to higher numbers
only if there are unacknowledged timestamps in flight. Compare this to
the old usage, where the timestamp ID used to monotonically increase
modulo OCELOT_MAX_PTP_ID.
In terms of implementation, this simplifies the bookkeeping of the
ocelot_port :: ts_id and ptp_skbs_in_flight. Since we need to traverse
the list of two-step timestampable skbs for each new packet anyway, the
information can already be computed and does not need to be stored.
Also, ocelot_port->tx_skbs is always accessed under the switch-wide
ocelot->ts_id_lock IRQ-unsafe spinlock, so we don't need the skb queue's
lock and can use the unlocked primitives safely.
This problem was actually detected using the tc-taprio offload, and is
causing trouble in TSN scenarios, which Felix (NXP LS1028A / VSC9959)
supports but Ocelot (VSC7514) does not. Thus, I've selected the commit
to blame as the one adding initial timestamping support for the Felix
switch.
Fixes: c0bcf53766 ("net: dsa: ocelot: add hardware timestamping support for Felix")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c53cdb95e ]
ocelot_get_txtstamp() is a threaded IRQ handler, requested explicitly as
such by both ocelot_ptp_rdy_irq_handler() and vsc9959_irq_handler().
As such, it runs with IRQs enabled, and not in hardirq context. Thus,
ocelot_port_add_txtstamp_skb() has no reason to turn off IRQs, it cannot
be preempted by ocelot_get_txtstamp(). For the same reason,
dev_kfree_skb_any_reason() will always evaluate as kfree_skb_reason() in
this calling context, so just simplify the dev_kfree_skb_any() call to
kfree_skb().
Also, ocelot_port_txtstamp_request() runs from NET_TX softirq context,
not with hardirqs enabled. Thus, ocelot_get_txtstamp() which shares the
ocelot_port->tx_skbs.lock lock with it, has no reason to disable hardirqs.
This is part of a larger rework of the TX timestamping procedure.
A logical subportion of the rework has been split into a separate
change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: b454abfab5 ("net: mscc: ocelot: be resilient to loss of PTP packets during transmission")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6fba4b3f0 ]
This condition, theoretically impossible to trigger, is not really
handled well. By "continuing", we are skipping the write to SYS_PTP_NXT
which advances the timestamp FIFO to the next entry. So we are reading
the same FIFO entry all over again, printing stack traces and eventually
killing the kernel.
No real problem has been observed here. This is part of a larger rework
of the timestamp IRQ procedure, with this logical change split out into
a patch of its own. We will need to "goto next_ts" for other conditions
as well.
Fixes: 9fde506e0c ("net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b01bec25b ]
If ocelot_port_add_txtstamp_skb() fails, for example due to a full PTP
timestamp FIFO, we must undo the skb_clone_sk() call with kfree_skb().
Otherwise, the reference to the skb clone is lost.
Fixes: 52849bcf00 ("net: mscc: ocelot: avoid overflowing the PTP timestamp FIFO")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11776cff0b ]
The dr_domain_add_vport_cap() function generally returns NULL on error
but sometimes we want it to return ERR_PTR(-EBUSY) so the caller can
retry. The problem here is that "ret" can be either -EBUSY or -ENOMEM
and if it's and -ENOMEM then the error pointer is propogated back and
eventually dereferenced in dr_ste_v0_build_src_gvmi_qpn_tag().
Fixes: 11a45def2e ("net/mlx5: DR, Add support for SF vports")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/07477254-e179-43e2-b1b3-3b9db4674195@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e64285ff41 ]
Since '1 << rocker_port->pport' may be undefined for port >= 32,
cast the left operand to 'unsigned long long' like it's done in
'rocker_port_set_enable()' above. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20241114151946.519047-1-dmantipov@yandex.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 078e0d596f ]
qca8k_phy_eth_command() is used to probe the child MDIO bus while the
parent MDIO is locked. This causes lockdep splat, reporting a possible
deadlock. It is not an actually deadlock, because different locks are
used. By making use of mutex_lock_nested() we can avoid this false
positive.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241110175955.3053664-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 857282b819 ]
This patch fixes a NULL pointer dereference bug in brcmfmac that occurs
when a high 'sd_sgentry_align' value applies (e.g. 512) and a lot of queued SKBs
are sent from the pkt queue.
The problem is the number of entries in the pre-allocated sgtable, it is
nents = max(rxglom_size, txglom_size) + max(rxglom_size, txglom_size) >> 4 + 1.
Given the default [rt]xglom_size=32 it's actually 35 which is too small.
Worst case, the pkt queue can end up with 64 SKBs. This occurs when a new SKB
is added for each original SKB if tailroom isn't enough to hold tail_pad.
At least one sg entry is needed for each SKB. So, eventually the "skb_queue_walk loop"
in brcmf_sdiod_sglist_rw may run out of sg entries. This makes sg_next return
NULL and this causes the oops.
The patch sets nents to max(rxglom_size, txglom_size) * 2 to be able handle
the worst-case.
Btw. this requires only 64-35=29 * 16 (or 20 if CONFIG_NEED_SG_DMA_LENGTH) = 464
additional bytes of memory.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241107132903.13513-1-nvbolhuis@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fa4f049dc ]
This patch fixes incorrect code alignment.
./drivers/net/wireless/intel/ipw2x00/libipw_rx.c:871:2-3: code aligned with following code on line 882.
./drivers/net/wireless/intel/ipw2x00/libipw_rx.c:886:2-3: code aligned with following code on line 900.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=11381
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241101060725.54640-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6aacd14844 ]
When the frag just got a page, then may lead to regression on VM.
Specially if the sysctl net.core.high_order_alloc_disable value is 1,
then the frag always get a page when do refill.
Which could see reliable crashes or scp failure (scp a file 100M in size
to VM).
The issue is that the virtnet_rq_dma takes up 16 bytes at the beginning
of a new frag. When the frag size is larger than PAGE_SIZE,
everything is fine. However, if the frag is only one page and the
total size of the buffer and virtnet_rq_dma is larger than one page, an
overflow may occur.
The commit f9dac92ba9 ("virtio_ring: enable premapped mode whatever
use_dma_api") introduced this problem. And we reverted some commits to
fix this in last linux version. Now we try to enable it and fix this
bug directly.
Here, when the frag size is not enough, we reduce the buffer len to fix
this problem.
Reported-by: "Si-Wei Liu" <si-wei.liu@oracle.com>
Tested-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd50c4125c ]
Cell-index value is obtained from Device Tree and then used to calculate
the index for accessing arrays port_mfl[], mac_mfl[] and intr_mng[].
In case of broken DT due to any error cell-index can contain any value
and it is possible to go beyond the array boundaries which can lead
at least to memory corruption.
Validate cell-index value obtained from Device Tree.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Link: https://patch.msgid.link/20241028065824.15452-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d10f1a4e44 ]
Currently reset state configuration of split header works fine for
non-tagged packets and we see no corruption in payload of any size
We need additional programming sequence with reset configuration to
handle VLAN tagged packets to avoid corruption in payload for packets
of size greater than 256 bytes.
Without this change ping application complains about corruption
in payload when the size of the VLAN packet exceeds 256 bytes.
With this change tagged and non-tagged packets of any size works fine
and there is no corruption seen.
Current configuration which has the issue for VLAN packet
----------------------------------------------------------
Split happens at the position at Layer 3 header
|MAC-DA|MAC-SA|Vlan Tag|Ether type|IP header|IP data|Rest of the payload|
2 bytes ^
|
With the fix we are making sure that the split happens now at
Layer 2 which is end of ethernet header and start of IP payload
Ip traffic split
-----------------
Bits which take care of this are SPLM and SPLOFST
SPLM = Split mode is set to Layer 2
SPLOFST = These bits indicate the value of offset from the beginning
of Length/Type field at which header split should take place when the
appropriate SPLM is selected. Reset value is 2bytes.
Un-tagged data (without VLAN)
|MAC-DA|MAC-SA|Ether type|IP header|IP data|Rest of the payload|
2bytes ^
|
Tagged data (with VLAN)
|MAC-DA|MAC-SA|VLAN Tag|Ether type|IP header|IP data|Rest of the payload|
2bytes ^
|
Non-IP traffic split such AV packet
------------------------------------
Bits which take care of this are
SAVE = Split AV Enable
SAVO = Split AV Offset, similar to SPLOFST but this is for AVTP
packets.
|Preamble|MAC-DA|MAC-SA|VLAN tag|Ether type|IEEE 1722 payload|CRC|
2bytes ^
|
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241016234313.3992214-1-quic_abchauha@quicinc.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3ced9bb90 ]
Arcadyan made routers with this PCI ID containing an AR2417.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930180716.139894-3-rosenp@gmail.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da04740124 ]
This is in two devices made by Gigaset, SX762 and SX763.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930180716.139894-2-rosenp@gmail.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fe45fada ]
The correct format string for resource_size_t is %pa which
acts on the address of the variable to be formatted [1].
[1] https://elixir.bootlin.com/linux/v6.11.3/source/Documentation/core-api/printk-formats.rst#L229
Introduced by commit 9d9326d3bc ("phy: Change mii_bus id field to a string")
Flagged by gcc-14 as:
drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c: In function 'fs_mii_bitbang_init':
drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c:126:46: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Wformat=]
126 | snprintf(bus->id, MII_BUS_ID_SIZE, "%x", res.start);
| ~^ ~~~~~~~~~
| | |
| | resource_size_t {aka long long unsigned int}
| unsigned int
| %llx
No functional change intended.
Compile tested only.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/netdev/711d7f6d-b785-7560-f4dc-c6aad2cce99@linux-m68k.org/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241014-net-pa-fmt-v1-2-dcc9afb8858b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020bfdc4ed ]
The correct format string for resource_size_t is %pa which
acts on the address of the variable to be formatted [1].
[1] https://elixir.bootlin.com/linux/v6.11.3/source/Documentation/core-api/printk-formats.rst#L229
Introduced by commit 9d9326d3bc ("phy: Change mii_bus id field to a string")
Flagged by gcc-14 as:
drivers/net/ethernet/freescale/fec_mpc52xx_phy.c: In function 'mpc52xx_fec_mdio_probe':
drivers/net/ethernet/freescale/fec_mpc52xx_phy.c:97:46: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Wformat=]
97 | snprintf(bus->id, MII_BUS_ID_SIZE, "%x", res.start);
| ~^ ~~~~~~~~~
| | |
| | resource_size_t {aka long long unsigned int}
| unsigned int
| %llx
No functional change intended.
Compile tested only.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/netdev/711d7f6d-b785-7560-f4dc-c6aad2cce99@linux-m68k.org/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241014-net-pa-fmt-v1-1-dcc9afb8858b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87e26448db ]
Vendor drivers r8125/r8126 indicate that this quirk isn't needed
any longer for RTL8126A. Mimic this in r8169.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/d1317187-aa81-4a69-b831-678436e4de62@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 630d5d8f2b ]
The return value of ieee80211_probereq_get() might be NULL, so check it
before using to avoid NULL pointer access.
Addresses-Coverity-ID: 1529805 ("Dereference null return value")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240919081216.28505-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 30447a1bc0 upstream.
Commit b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround
broken TEF FIFO tail index erratum") introduced
mcp251xfd_get_tef_len() to get the number of unhandled transmit events
from the Transmit Event FIFO (TEF).
As the TEF has no head index, the driver uses the TX-FIFO's tail index
instead, assuming that send frames are completed.
When calculating the number of unhandled TEF events, that commit
didn't take mcp2518fd erratum DS80000789E 6. into account. According
to that erratum, the FIFOCI bits of a FIFOSTA register, here the
TX-FIFO tail index might be corrupted.
However here it seems the bit indicating that the TX-FIFO is
empty (MCP251XFD_REG_FIFOSTA_TFERFFIF) is not correct while the
TX-FIFO tail index is.
Assume that the TX-FIFO is indeed empty if:
- Chip's head and tail index are equal (len == 0).
- The TX-FIFO is less than half full.
(The TX-FIFO empty case has already been checked at the
beginning of this function.)
- No free buffers in the TX ring.
If the TX-FIFO is assumed to be empty, assume that the TEF is full and
return the number of elements in the TX-FIFO (which equals the number
of TEF elements).
If these assumptions are false, the driver might read to many objects
from the TEF. mcp251xfd_handle_tefif_one() checks the sequence numbers
and will refuse to process old events.
Reported-by: Renjaya Raga Zenta <renjaya.zenta@formulatrix.com>
Closes: https://patch.msgid.link/CAJ7t6HgaeQ3a_OtfszezU=zB-FqiZXqrnATJ3UujNoQJJf7GgA@mail.gmail.com
Fixes: b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround broken TEF FIFO tail index erratum")
Tested-by: Renjaya Raga Zenta <renjaya.zenta@formulatrix.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20241126-mcp251xfd-fix-length-calculation-v2-1-c2ed516ed6ba@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee1dfbdd8b upstream.
In commit 6e86a1543c ("can: dev: provide optional GPIO based
termination support") GPIO based termination support was added.
For no particular reason that patch uses gpiod_set_value() to set the
GPIO. This leads to the following warning, if the systems uses a
sleeping GPIO, i.e. behind an I2C port expander:
| WARNING: CPU: 0 PID: 379 at /drivers/gpio/gpiolib.c:3496 gpiod_set_value+0x50/0x6c
| CPU: 0 UID: 0 PID: 379 Comm: ip Not tainted 6.11.0-20241016-1 #1 823affae360cc91126e4d316d7a614a8bf86236c
Replace gpiod_set_value() by gpiod_set_value_cansleep() to allow the
use of sleeping GPIOs.
Cc: Nicolai Buchwitz <nb@tipi-net.de>
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reported-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Tested-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Fixes: 6e86a1543c ("can: dev: provide optional GPIO based termination support")
Link: https://patch.msgid.link/20241121-dev-fix-can_set_termination-v1-1-41fa6e29216d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5085f861b4 ]
Previously a workaround was added to avoid syndrome 0xcdb051. It is
triggered when offload a rule with tunnel encapsulation, and
forwarding to another table, but not matching on the internal port in
firmware steering mode. The original workaround skips internal tunnel
port logic, which is not correct as not all cases are considered. As
an example, if vlan is configured on the uplink port, traffic can't
pass because vlan header is not added with this workaround. Besides,
there is no such issue for software steering. So, this patch removes
that, and returns error directly if trying to offload such rule for
firmware steering.
Fixes: 06b4eac9c4 ("net/mlx5e: Don't offload internal port if filter device is out device")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Tested-by: Frode Nordahl <frode.nordahl@canonical.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 217bbf156f ]
The driver is currently using an ACL key block that is not supported by
Spectrum-4. This works because the driver is only using a single field
from this key block which is located in the same offset in the
equivalent Spectrum-4 key block.
The issue was discovered when the firmware started rejecting the use of
the unsupported key block. The change has been reverted to avoid
breaking users that only update their firmware.
Nonetheless, fix the issue by using the correct key block.
Fixes: 07ff135958 ("mlxsw: Introduce flex key elements for Spectrum-4")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/35e72c97bdd3bc414fb8e4d747e5fb5d26c29658.1733237440.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bec2a32145 ]
'struct mlxsw_afk_element_inst' are not modified in these drivers.
Constifying these structures moves some data to a read-only section, so
increases overall security.
Update a few functions and struct mlxsw_afk_block accordingly.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
4278 4032 0 8310 2076 drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_flex_keys.o
After:
=====
text data bss dec hex filename
7934 352 0 8286 205e drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_flex_keys.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/8ccfc7bfb2365dcee5b03c81ebe061a927d6da2e.1727541677.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 217bbf156f ("mlxsw: spectrum_acl_flex_keys: Use correct key block on Spectrum-4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cad6431b86 ]
For 12 key blocks in the A-TCAM, rules are split into two records, which
constitute two lookups. The two records are linked using a
"large entry key ID".
Due to a Spectrum-4 hardware issue, KVD entries that correspond to key
blocks 0 to 5 of 12 key blocks A-TCAM entries will be placed in the same
KVD pipe if they only differ in their "large entry key ID", as it is
ignored. This results in a reduced scale. To reduce the probability of this
issue, we can place key blocks with high entropy in blocks 0 to 5. The idea
is to place blocks that are changed often in blocks 0 to 5, for
example, key blocks that match on IPv4 addresses or the LSBs of IPv6
addresses. Such placement will reduce the probability of these blocks to be
same.
Mark several blocks with 'high_entropy' flag, so later we will take into
account this flag and place them in blocks 0 to 5.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 217bbf156f ("mlxsw: spectrum_acl_flex_keys: Use correct key block on Spectrum-4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92953e7aab ]
Two ACL regions that are configured by the driver during initialization are
the ones used for IPv4 and IPv6 multicast forwarding. Entries residing
in these two regions match on the {SIP, DIP, VRID} key elements.
Currently for IPv6 region, 9 key blocks are used:
* 4 for SIP - 'ipv4_1', 'ipv6_{3,4,5}'
* 4 for DIP - 'ipv4_0', 'ipv6_{0,1,2/2b}'
* 1 for VRID - 'ipv4_4b'
This can be improved by reducing the amount key blocks needed for
the IPv6 region to 8. It is possible to use key blocks that mix subsets of
the VRID element with subsets of the DIP element.
The following key blocks can be used:
* 4 for SIP - 'ipv4_1', 'ipv6_{3,4,5}'
* 1 for subset of DIP - 'ipv4_0'
* 3 for the rest of DIP and subsets of VRID - 'ipv6_{0,1,2/2b}'
To make this happen, add VRID sub-elements as part of existing keys -
'ipv6_{0,1,2/2b}'. Note that one of the sub-elements is called
VRID_ROUTER_MSB and does not contain bit numbers like the rest, as for
Spectrum < 4 this element represents bits 8-10 and for Spectrum-4 it
represents bits 8-11.
Breaking VRID into 3 sub-elements makes the driver use one less block in
IPv6 region for multicast forwarding. The sub-elements can be filled in
blocks that are used for destination IP.
The algorithm in the driver that chooses which key blocks will be used is
lazy and not the optimal one. It searches the block that contains the most
elements that are required, chooses it, removes the elements that appear
in the chosen block and starts again searching the block that contains the
most elements.
When key block 'ipv4_4' is defined, the algorithm might choose it, as it
contains 2 sub-elements of VRID, then 8 blocks must be chosen for SIP and
DIP and we get 9 blocks to match on {SIP, DIP, VRID}. That is why we had to
remove key block 'ipv4_4' in a previous patch and use key block that
contains one field for VRID.
This improvement was tested and indeed 8 blocks are used instead of 9.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 217bbf156f ("mlxsw: spectrum_acl_flex_keys: Use correct key block on Spectrum-4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
