[ Upstream commit c6dcd8050f ]
When using a leon kernel with qemu there where no console prompt.
The root cause is the handling of the fifo size in the tx part of the
apbuart driver.
The qemu uart driver only have a very rudimentary status handling and do
not report the number of chars queued in the tx fifo in the status register.
So the driver ends up with a fifo size of 1.
In the tx path the fifo size is divided by 2 - resulting in a fifo
size of zero.
The original implementation would always try to send one char, but
after the introduction of uart_port_tx_limited() the fifo size is
respected even for the first char.
There seems to be no good reason to divide the fifo size with two - so
remove this. It looks like something copied from the original amba driver.
With qemu we now have a minimum fifo size of one char, so we show
the prompt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: d11cc8c3c4 ("tty: serial: use uart_port_tx_limited()")
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: <linux-serial@vger.kernel.org>
Cc: <sparclinux@vger.kernel.org>
Link: https://lore.kernel.org/r/20231226121607.GA2622970@ravnborg.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78d60dae9a ]
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Fixes: cb1a609236 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad90d0358b ]
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow. So all resources that were not freed
are leaked in this case. Skipping serial8250_unregister_port() has the
potential to keep enough of the UART around to trigger a use-after-free.
So replace the error return (and with it the little helpful error
message) by a more useful error message and continue to cleanup.
Fixes: e3f0c638f4 ("serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231110152927.70601-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3ef79cd141 upstream.
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d710b769c upstream.
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f93776b8 upstream.
The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.
Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before uart_get_rs485_mode() gets
called.
Also replace the assignment of rs485_config() to have the complete RS485
setup in one function.
Fixes: e2752ae3cf ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-7-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c2a5f471c upstream.
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c45eaa813 upstream.
There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74eab89b26 upstream.
If the imx driver cannot support RS485 it nullifies the ports
rs485_supported structure. But it still calls uart_get_rs485_mode() which
may set the RS485_ENABLED flag nevertheless.
This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.
Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.
With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. So remove this check.
Furthermore the explicit nullifcation of rs485_supported is not needed,
since the memory has already been set to zeros at allocation. So remove
this, too.
Fixes: 00d7a00e2a ("serial: imx: Fill in rs485_supported")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-6-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a33e33ca0 upstream.
If the RS485 feature RX-during-TX is supported by means of a GPIO set the
according supported flag. Otherwise setting this feature from userspace may
not be possible, since in uart_sanitize_serial_rs485() the passed RS485
configuration is matched against the supported features and unsupported
settings are thereby removed and thus take no effect.
Cc: <stable@vger.kernel.org>
Fixes: 163f080eb7 ("serial: core: Add option to output RS485 RX_DURING_TX state via GPIO")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-3-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c73986913f upstream.
Some uart drivers specify a rs485_config() function and then decide later
to disable RS485 support for some reason (e.g. imx and ar933).
In these cases userspace may be able to activate RS485 via TIOCSRS485
nevertheless, since in uart_set_rs485_config() an existing rs485_config()
function indicates that RS485 is supported.
Make sure that this is not longer possible by checking the uarts
rs485_supported.flags instead and bailing out if SER_RS485_ENABLED is not
set.
Furthermore instead of returning an empty structure return -ENOTTY if the
RS485 configuration is requested via TIOCGRS485 but RS485 is not supported.
This has a small impact on userspace visibility but it is consistent with
the -ENOTTY error for TIOCGRS485.
Fixes: e849145e1f ("serial: ar933x: Fill in rs485_supported")
Fixes: 55e18c6b6d ("serial: imx: Remove serial_rs485 sanitization")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-5-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4afeced55b upstream.
Among other things uart_sanitize_serial_rs485() tests the sanity of the RTS
settings in a RS485 configuration that has been passed by userspace.
If RTS-on-send and RTS-after-send are both set or unset the configuration
is adjusted and RTS-after-send is disabled and RTS-on-send enabled.
This however makes only sense if both RTS modes are actually supported by
the driver.
With commit be2e2cb1d2 ("serial: Sanitize rs485_struct") the code does
take the driver support into account but only checks if one of both RTS
modes are supported. This may lead to the errorneous result of RTS-on-send
being set even if only RTS-after-send is supported.
Fix this by changing the implemented logic: First clear all unsupported
flags in the RS485 configuration, then adjust an invalid RTS setting by
taking into account which RTS mode is supported.
Cc: <stable@vger.kernel.org>
Fixes: be2e2cb1d2 ("serial: Sanitize rs485_struct")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-4-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07c30ea586 upstream.
Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
Since this function is called with the port lock held, this can be a
problem in case that setting the GPIO line can sleep (e.g. if a GPIO
expander is used which is connected via SPI or I2C).
Avoid this issue by moving the GPIO setting outside of the port lock into
the serial core and thus making it a generic feature.
Also with commit c54d485436 ("serial: stm32: Add support for rs485
RX_DURING_TX output GPIO") the SER_RS485_RX_DURING_TX flag is only set if a
rx-during-tx GPIO is _not_ available, which is wrong. Fix this, too.
Furthermore reset old GPIO settings in case that changing the RS485
configuration failed.
Fixes: c54d485436 ("serial: stm32: Add support for rs485 RX_DURING_TX output GPIO")
Fixes: ca530cfa96 ("serial: imx: Add support for RS485 RX_DURING_TX output GPIO")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Granite Rapids-D has an additional UART that is enumerated via ACPI.
Add ACPI ID for it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231205195524.2705965-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console is immediately assigned to the ma35d1 port without
checking its index. This oversight can lead to out-of-bounds
errors when the index falls outside the valid '0' to
MA35_UART_NR range. Such scenario trigges ran error like the
following:
UBSAN: array-index-out-of-bounds in drivers/tty/serial/ma35d1_serial.c:555:51
index -1 is out of range for type 'uart_ma35d1_port [17]
Check the index before using it and bail out with a warning.
Fixes: 930cbf92db ("tty: serial: Add Nuvoton ma35d1 serial driver support")
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Cc: Jacky Huang <ychuang3@nuvoton.com>
Cc: <stable@vger.kernel.org> # v6.5+
Link: https://lore.kernel.org/r/20231204163804.1331415-2-andi.shyti@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is no guarantee that the memory returned by
dma_alloc_coherent() is associated with a 'struct page', using the
architecture specific phys_to_page() is wrong, but using
virt_to_page() would be as well.
Stop using sg lists altogether and just use the *_single() functions
instead. This also simplifies the code a bit since the scatterlists in
this driver always have only one entry anyway.
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
gc: Add a commit log from the initial thread:
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
Fixes: cb06ff102e ("ARM: PL011: Add support for Rx DMA buffer polling.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231122171503.235649-1-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes commit 439c7183e5 ("serial: 8250: 8250_omap: Disable RX
interrupt after DMA enable") which unfortunately set the
UART_HAS_RHR_IT_DIS bit in the UART_OMAP_IER2 register and never
cleared it.
Cc: stable@vger.kernel.org
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031110909.11695-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there is no support for earlycon on the AM654 UART
controller. This commit adds it.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031131242.15516-1-rwahl@gmx.de
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting RX DMA on THRI interrupt is too early because TX may not have
finished yet.
This change is inspired by commit 90b8596ac4 ("serial: 8250: Prevent
starting up DMA Rx on THRI interrupt") and fixes DMA issues I had with
an AM62 SoC that is using the 8250 OMAP variant.
Cc: stable@vger.kernel.org
Fixes: c26389f998 ("serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231101171431.16495-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=g+6E
-----END PGP SIGNATURE-----
Merge tag 'mips_6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed AR7 platform support
- cleanups and fixes
* tag 'mips_6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: AR7: remove platform
watchdog: ar7_wdt: remove driver to prepare for platform removal
vlynq: remove bus driver
mtd: parsers: ar7: remove support
serial: 8250: remove AR7 support
arch: mips: remove ReiserFS from defconfig
MIPS: lantiq: Remove unnecessary include of <linux/of_irq.h>
MIPS: lantiq: Fix pcibios_plat_dev_init() "no previous prototype" warning
MIPS: KVM: Fix a build warning about variable set but not used
MIPS: Remove dead code in relocate_new_kernel
mips: dts: ralink: mt7621: rename to GnuBee GB-PC1 and GnuBee GB-PC2
mips: dts: ralink: mt7621: define each reset as an item
mips: dts: ingenic: Remove unneeded probe-type properties
MIPS: loongson32: Remove dma.h and nand.h
Here is the big set of tty/serial driver changes for 6.7-rc1. Included
in here are:
- console/vgacon cleanups and removals from Arnd
- tty core and n_tty cleanups from Jiri
- lots of 8250 driver updates and cleanups
- sc16is7xx serial driver updates
- dt binding updates
- first set of port lock wrapers from Thomas for the printk fixes
coming in future releases
- other small serial and tty core cleanups and updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUTbaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk9+gCeKdoRb8FDwGCO/GaoHwR4EzwQXhQAoKXZRmN5
LTtw9sbfGIiBdOTtgLPb
=6PJr
-----END PGP SIGNATURE-----
Merge tag 'tty-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.7-rc1. Included
in here are:
- console/vgacon cleanups and removals from Arnd
- tty core and n_tty cleanups from Jiri
- lots of 8250 driver updates and cleanups
- sc16is7xx serial driver updates
- dt binding updates
- first set of port lock wrapers from Thomas for the printk fixes
coming in future releases
- other small serial and tty core cleanups and updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (193 commits)
serdev: Replace custom code with device_match_acpi_handle()
serdev: Simplify devm_serdev_device_open() function
serdev: Make use of device_set_node()
tty: n_gsm: add copyright Siemens Mobility GmbH
tty: n_gsm: fix race condition in status line change on dead connections
serial: core: Fix runtime PM handling for pending tx
vgacon: fix mips/sibyte build regression
dt-bindings: serial: drop unsupported samsung bindings
tty: serial: samsung: drop earlycon support for unsupported platforms
tty: 8250: Add note for PX-835
tty: 8250: Fix IS-200 PCI ID comment
tty: 8250: Add Brainboxes Oxford Semiconductor-based quirks
tty: 8250: Add support for Intashield IX cards
tty: 8250: Add support for additional Brainboxes PX cards
tty: 8250: Fix up PX-803/PX-857
tty: 8250: Fix port count of PX-257
tty: 8250: Add support for Intashield IS-100
tty: 8250: Add support for Brainboxes UP cards
tty: 8250: Add support for additional Brainboxes UC cards
tty: 8250: Remove UC-257 and UC-431
...
The ia64 architecture gets its well-earned retirement as planned,
now that there is one last (mostly) working release that will
be maintained as an LTS kernel.
The architecture specific system call tables are updated for
the added map_shadow_stack() syscall and to remove references
to the long-gone sys_lookup_dcookie() syscall.
-----BEGIN PGP SIGNATURE-----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=H1vH
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull ia64 removal and asm-generic updates from Arnd Bergmann:
- The ia64 architecture gets its well-earned retirement as planned,
now that there is one last (mostly) working release that will be
maintained as an LTS kernel.
- The architecture specific system call tables are updated for the
added map_shadow_stack() syscall and to remove references to the
long-gone sys_lookup_dcookie() syscall.
* tag 'asm-generic-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
hexagon: Remove unusable symbols from the ptrace.h uapi
asm-generic: Fix spelling of architecture
arch: Reserve map_shadow_stack() syscall number for all architectures
syscalls: Cleanup references to sys_lookup_dcookie()
Documentation: Drop or replace remaining mentions of IA64
lib/raid6: Drop IA64 support
Documentation: Drop IA64 from feature descriptions
kernel: Drop IA64 support from sig_fault handlers
arch: Remove Itanium (IA-64) architecture
Richard reported that a serial port may end up sometimes with tx data
pending in the buffer for long periods of time.
Turns out we bail out early on any errors from pm_runtime_get(),
including -EINPROGRESS. To fix the issue, we need to ignore -EINPROGRESS
as we only care about the runtime PM usage count at this point. We check
for an active runtime PM state later on for tx.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Bruce Ashfield <bruce.ashfield@gmail.com>
Cc: Mikko Rapeli <mikko.rapeli@linaro.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Randy MacLeod <randy.macleod@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231023074856.61896-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks") removed
support here for several old platforms, but kept support for earlycon
for those same platforms.
As earlycon support for otherwise unsupported platforms doesn't seem to
be useful, just drop it as well.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20231019100639.4026283-1-andre.draszik@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the PCI comment for the IS-200 card. The PCI ID for the IS-200
is 0x0d80, and the definition used (PCI_DEVICE_ID_INTASHIELD_IS200)
is indeed 0x0d80, clarify that by fixing the comment as its
neighbouring cards are all at 0x0020 offsets.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB78993B6AD85F6550AF6590FBC4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the later revisions of the Brainboxes PX cards are based
on the Oxford Semiconductor chipset. Due to the chip's unique setup
these cards need to be initialised.
Previously these were tested against a reference card with the same broken
baudrate on another PC, cancelling out the effect. With this patch they
work and can transfer/receive find against an FTDI-based device.
Add all of the cards which require this setup to the quirks table.
Thanks to Maciej W. Rozycki for clarification on this chip.
Fixes: ef5a03a26c ("tty: 8250: Add support for Brainboxes PX cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB7899D222A4AB2A4E8C57108FC4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UC-257 is a serial + LPT card, so remove it from this driver.
A patch has been submitted to add it to parport_serial instead.
Additionaly, the UC-431 does not use this card ID, only the UC-420
does. The 431 is a 3-port card and there is no generic 3-port configuration
available, so remove reference to it from this driver.
Fixes: 152d1afa83 ("tty: Add support for Brainboxes UC cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB78995ADF7394C74AD4CF3357C4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the console suspend is disabled, the genpd of the console shall not
be powered-off during suspend.
Set the flag GENPD_FLAG_ALWAYS_ON to the corresponding genpd during
suspend, and restore the original value during the resume.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20231017130540.1149721-1-thomas.richard@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move PCI_DEVICE_ID macros to the top so that these macros can be used
throughout 8250_pci.c
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20231018091739.10125-4-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When support for various old platforms was removed in commit
1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks"),
s3c24xx_serial_ops also became unused here because nothing sets port
type TYPE_S3C24XX anymore.
Remove s3c24xx_serial_ops and all the code that's unreachable now.
Fixes: 1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks")
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20231019100901.4026680-1-andre.draszik@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
esp32s3 variant of the esp32 UART has limited baudrate divisor range
that does not allow it to use 9600 and lower rates with 40MHz input
clock. Use clock prescaler present in this UART variant to help with
that.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231018191252.1551972-1-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AR7 is going to be removed from the Kernel, so remove its type
definition from 8250 code. As with previous removals, I checked with
Debian Code Search that 'PORT_AR7' is not used in userspace.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
uart_get_baud_rate has input parameters 'min' and 'max' limiting the
range of acceptable baud rates from the caller's perspective. If neither
current or old termios structures have acceptable baud rate setting and
9600 is not in the min/max range either the function returns 0 and
issues a warning.
However for a UART that does not support speed of 9600 baud this is
expected behavior.
Clarify that 0 can be (and always could be) returned from the
uart_get_baud_rate. Don't issue a warning in that case.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231010085926.1021667-2-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
