"select REGMAP_SOUNDWIRE_MBQ" to fix build error:
ERROR: modpost: "__devm_regmap_init_sdw_mbq"
[sound/soc/codecs/snd-soc-tac5xx2-sdw.ko] undefined!
Signed-off-by: Niranjan H Y <niranjan.hy@ti.com>
Link: https://patch.msgid.link/20260807151623.3005-1-niranjan.hy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
rt1320_io_init() applies the vendor initialisation preset only when the
amplifier's SDCA function status has FUNCTION_NEEDS_INITIALIZATION set:
if ((amp_func_status & FUNCTION_NEEDS_INITIALIZATION)) {
Its two sibling drivers guard the same write differently, also running
the preset on the first hardware init:
rt712-sdca.c: if ((amp_func_status & FUNCTION_NEEDS_INITIALIZATION) ||
(!rt712->first_hw_init)) {
rt722-sdca.c: if ((amp_func_status & FUNCTION_NEEDS_INITIALIZATION) ||
(!rt722->first_hw_init)) {
On the Microsoft Surface Pro 11 (Intel) the RT1320 never sets that bit.
Its function status reads back 0x41 on every boot, cold or warm:
rt1320-sdca sdw:0:0:025d:1320:01: rt1320_io_init amp func_status=0x41
which is NEWLY_ATTACHED | FUNCTION_HAS_BEEN_RESET: the function reports
that it has been reset and does not consider itself in need of
initialisation. Bit 5 is never set, so the preset never runs,
rt1320_vc_preset() and the MCU patch load are skipped, and the amplifier
is left unprogrammed. rt712 and rt722 would have run it via their
first_hw_init fallback.
Add the same fallback. With it rt1320_vc_preset() executes and the
amplifier reports RT1320_KR0_INT_READY=0x1f where previously it did not.
Signed-off-by: Sergey Lebedev <lsa.uz@pm.me>
Link: https://patch.msgid.link/20260804225853.31585-2-lsa.uz@pm.me
Signed-off-by: Mark Brown <broonie@kernel.org>
The only initial jack detect is the rt5645_irq(0, rt5645) at the end of
rt5645_set_jack_detect(). A card described with simple-audio-card has no
machine driver to call that, so jack state is only ever sampled from an
edge on hp-detect-gpios.
A headphone already in the socket at boot is therefore never noticed, and
the card is silent with every mixer control set correctly.
rt5645_jack_detect() is what force enables the "LDO2" and "Mic Det Power"
supplies that the "HP amp" widget depends on, and what programs
RT5645_CHARGE_PUMP away from its reset value, so without it "HP amp"
cannot power up. Unplugging and replugging the jack is the only way to
recover.
Do the detect at the end of the component probe when the driver owns a
hp-detect GPIO and the codec's own jack detect is unused, which is the
case that has no other trigger. A machine driver calling
rt5645_set_jack_detect() later just repeats it.
Signed-off-by: Rudi Heitbaum <rudi@heitbaum.com>
Link: https://patch.msgid.link/anNU3tOUR7rOReSB@5e001e58230e
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove invalid goto exit paths that jump across guard(mutex) cleanup
variable initialization, replace them with direct kfree(src) and return,
to fix the s390 clang build error in acoustic_ctl_write().
Fixes: d75d38dc46 ("ASoC: tas2781: Add a debugfs node for acoustic tuning")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20260807000304.826-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi <peter.ujfalusi@linux.intel.com> says:
reg_defaults must be sorted by ascending register address as
regcache_lookup_reg() locates the entries in it with bsearch(), see commit
fd80df352b ("regcache: Add support for sorting defaults arrays").
These three tables have entries which are out of order, so the binary search
does not find part of them. For those registers regcache_reg_needs_sync()
cannot compare the cached value against the default and reports that a sync
is needed, so they are written to the device on every regcache_sync() even
when they were never touched.
The patches only reorder the existing entries, the text of every entry is
kept verbatim and no default value is changed. Each table was verified by
evaluating the register addresses and replaying lib/bsearch.c on them.
Entries not reachable by the binary search, per table:
cs35l41_reg 2 (of 47)
cs35l45_defaults 36 (of 73)
cs4265_reg_defaults 3 (of 16)
For cs35l45 this is nearly half of the table: the DSP1_RX*_RATE and
DSP1_TX*_RATE registers sit in the middle of it while their addresses are
far above everything else, which cuts the search off from the whole
0x4c40 - 0xf010 range.
Found by an audit of all reg_defaults tables under sound/, the SoundWire
codec drivers are fixed by a separate series.
Link: https://patch.msgid.link/20260805082413.26174-1-peter.ujfalusi@linux.intel.com
reg_defaults must be sorted by ascending register address, as
regcache_lookup_reg() locates entries in it with bsearch(). See commit
fd80df352b ("regcache: Add support for sorting defaults arrays").
cs4265_reg_defaults[] lists CS4265_INT_MASK (0x0e),
CS4265_STATUS_MODE_MSB (0x0f) and CS4265_STATUS_MODE_LSB (0x10) after
CS4265_SPDIF_CTL1 (0x11) and CS4265_SPDIF_CTL2 (0x12), so the binary search
does not find those three entries. regcache_reg_needs_sync() then cannot
compare them against their default and reports that a sync is needed, so
they are written to the device on every regcache_sync() even when they were
never touched.
Sort the table by register address.
Fixes: fb6f806967 ("ASoC: Add support for the CS4265 CODEC")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260805082413.26174-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
reg_defaults must be sorted by ascending register address, as
regcache_lookup_reg() locates entries in it with bsearch(). See commit
fd80df352b ("regcache: Add support for sorting defaults arrays").
cs35l45_defaults[] lists the DSP1_RX*_RATE and DSP1_TX*_RATE registers
(0x02b80080 - 0x02b802b8) in the middle of the table, ahead of entries with
much lower addresses, so the binary search does not find 36 of its 73
entries. regcache_reg_needs_sync() then cannot compare those against their
default and reports that a sync is needed, so they are written to the
device on every regcache_sync() even when they were never touched.
Sort the table by register address.
Fixes: 74b14e2850 ("ASoC: cs35l45: DSP Support")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260805082413.26174-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
reg_defaults must be sorted by ascending register address, as
regcache_lookup_reg() locates entries in it with bsearch(). See commit
fd80df352b ("regcache: Add support for sorting defaults arrays").
cs35l41_reg[] lists CS35L41_BSTCVRT_PEAK_CUR (0x3808) after
CS35L41_BSTCVRT_COEFF (0x3810) and CS35L41_BSTCVRT_SLOPE_LBST (0x3814), so
the binary search does not find those two entries.
regcache_reg_needs_sync() then cannot compare them against their default
and reports that a sync is needed, so they are written to the device on
every regcache_sync() even when they were never touched.
Sort the table by register address.
Fixes: 5f2f539901 ("ASoC: cs35l41: Correct handling of some registers in the cache")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260805082413.26174-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_RT5645 has no prompt, so it can only be turned on by a machine
driver that selects it. Every such driver is x86, MediaTek or Rockchip,
which leaves the codec unreachable on any other platform.
The part has a devicetree binding of its own,
Documentation/devicetree/bindings/sound/realtek,rt5645.yaml, and nothing
in the driver is machine specific, so a board that describes it with
simple-audio-card or audio-graph-card should be able to build it. Today
there is no configuration in which that is possible.
Give the symbol a prompt, matching SND_SOC_RT5640 immediately above it.
The machine drivers that select it are unaffected.
Signed-off-by: Rudi Heitbaum <rudi@heitbaum.com>
Link: https://patch.msgid.link/anCcciWmO6QOLTsl@5e001e58230e
Signed-off-by: Mark Brown <broonie@kernel.org>
Dawid Wróbel <me@dawidwrobel.com> says:
Both drivers access enumerated controls through value.integer.value[0]
instead of value.enumerated.item[0]. The same bug was fixed in rx-macro
and va-macro in 2022 (bcfe5f76cc, 0ea5eff7c6); tx-macro and
wsa-macro were missed.
On 64-bit kernels with CONFIG_SND_CTL_DEBUG this trips the elem value
sanity check, and every read of the affected controls fails with
-EINVAL.
Reproduced and fixed on a Xiaomi Mi Pad 5 Pro (SM8250) for tx-macro.
wsa-macro is compile-tested only — that codec is not instantiated on
this hardware.
Link: https://patch.msgid.link/20260730-worktree-lpass-tx-macro-enum-fix-v2-0-6d091c736116@dawidwrobel.com
EAR SPKR PA Gain" and the four "WSA RX* Mux" controls are enumerated,
but their get and put callbacks access the value through
ucontrol->value.integer.value[0] (a long) instead of
ucontrol->value.enumerated.item[0] (an unsigned int).
This same pattern was fixed in the sibling drivers by
commit bcfe5f76cc ("ASoC: codecs: rx-macro: fix accessing array
out of bounds for enum type") and
commit 0ea5eff7c6 ("ASoC: codecs: va-macro: fix accessing array
out of bounds for enum type"), but wsa-macro was missed.
On 64-bit kernels with CONFIG_SND_CTL_DEBUG this trips the elem value
sanity check and every read of these controls fails with -EINVAL.
Fixes: 809bcbcece ("ASoC: codecs: lpass-wsa-macro: Add support to WSA Macro")
Fixes: 2c4066e5d4 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Assisted-by: Claude:claude-fable-5
Cc: stable@vger.kernel.org
Signed-off-by: Dawid Wróbel <me@dawidwrobel.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260730-worktree-lpass-tx-macro-enum-fix-v2-2-6d091c736116@dawidwrobel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "DEC0 MODE" to "DEC7 MODE" controls are enumerated, but
tx_macro_dec_mode_get() and tx_macro_dec_mode_put() access their
value through ucontrol->value.integer.value[0] (a long) instead of
ucontrol->value.enumerated.item[0] (an unsigned int).
This same pattern was fixed in the sibling drivers by
commit bcfe5f76cc ("ASoC: codecs: rx-macro: fix accessing array
out of bounds for enum type") and
commit 0ea5eff7c6 ("ASoC: codecs: va-macro: fix accessing array
out of bounds for enum type"), but tx-macro was missed.
On 64-bit kernels built with CONFIG_SND_CTL_DEBUG, the elem value
sanity check catches the 4 bytes written past the enumerated item
and every read of these controls fails with -EINVAL:
snd-sm8250 sound: control 2:0:0:DEC0 MODE:0: access overflow
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Assisted-by: Claude:claude-fable-5
Cc: stable@vger.kernel.org
Signed-off-by: Dawid Wróbel <me@dawidwrobel.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260730-worktree-lpass-tx-macro-enum-fix-v2-1-6d091c736116@dawidwrobel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SINEGAIN2_REG case in cali_reg_update() references t->sin_gn[]
rather than t->sin_gn2[], causing the second pilot tone gain
calibration to be programmed with the wrong register address.
These are distinct fields in struct fct_param_address and are
populated from separate firmware parameters by the parser in
tas2781-fmwlib.c.
Fixes: 84d6a465f2 ("ASoC: tas2781: Support dsp firmware Alpha and Beta seaies")
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20260720081616.631413-1-wangdich9700@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In max98090_probe(), the -EPROBE_DEFER check after devm_clk_get() is
broken due to a missing IS_ERR() guard.
The code intends to return -EPROBE_DEFER only when the clock lookup
fails with that specific error. However, without IS_ERR() the check:
if (PTR_ERR(max98090->mclk) == -EPROBE_DEFER)
is called unconditionally, including when devm_clk_get() succeeds and
returns a valid pointer. Calling PTR_ERR() on a valid pointer
reinterprets its address as a signed long; the result is arbitrary
and is almost never equal to -EPROBE_DEFER, so the check silently
does nothing in the success case. When devm_clk_get() fails with
any error other than -EPROBE_DEFER the check is also skipped, leaving
max98090->mclk holding an error pointer with no indication to the caller.
This means a deferred probe will never actually be triggered for this
device, and any non-EPROBE_DEFER clock error is silently swallowed with
the error pointer left in the mclk field.
Fix this by adding the missing IS_ERR() guard around the PTR_ERR() call,
matching the pattern already used in the sibling max98088 and wm8960
drivers.
Fixes: b10ab7b838 ("ASoC: max98090: Add master clock handling")
Signed-off-by: Uday Khare <udaykhare77@gmail.com>
Link: https://patch.msgid.link/20260720104254.14948-1-udaykhare77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In max98095_probe(), the -EPROBE_DEFER check after devm_clk_get() is
broken due to a missing IS_ERR() guard.
The code intends to return -EPROBE_DEFER only when the clock lookup
fails with that specific error. However, without IS_ERR() the check:
if (PTR_ERR(max98095->mclk) == -EPROBE_DEFER)
is called unconditionally, including when devm_clk_get() succeeds and
returns a valid pointer. Calling PTR_ERR() on a valid pointer
reinterprets its address as a signed long; the result is arbitrary
and is almost never equal to -EPROBE_DEFER, so the check silently
does nothing in the success case. When devm_clk_get() fails with
any error other than -EPROBE_DEFER the check is also skipped, leaving
max98095->mclk holding an error pointer with no indication to the caller.
This means a deferred probe will never actually be triggered for this
device, and any non-EPROBE_DEFER clock error is silently swallowed with
the error pointer left in the mclk field.
Fix this by adding the missing IS_ERR() guard around the PTR_ERR() call,
matching the pattern already used in the sibling max98088 and wm8960
drivers.
Fixes: e3048c3d2b ("ASoC: max98095: Add master clock handling")
Signed-off-by: Uday Khare <udaykhare77@gmail.com>
Link: https://patch.msgid.link/20260720103950.14474-1-udaykhare77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown <broonie@kernel.org> says:
While reviewing another fix for the tas2562 volume control I noticed a
few issues with the put() operation, this series fixes them.
It's also a bit weird that the volume control is defined with twice as
many values as can actually be set, probably the best fix there is to
regnerate the table of volume values with the intermediate values.
Link: https://patch.msgid.link/20260715-asoc-tas2562-put-retval-v1-0-97bf467c924e@kernel.org
The tas2562 digital volume is spread over four registers and is implemented
as lookups into a table so the driver stores the value for the userspace
control in the driver data. This defaults to 0 due to kzalloc() but the
register default is 0x40400000 which maps onto something a bit over the
largest value defined in the lookup table. While it's not an exact match
update the default to the largest value, avoiding user surprise due to a
sudden change on first write.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260715-asoc-tas2562-put-retval-v1-3-97bf467c924e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA put() operations should return 0 for noop updates and 1 if the
value of the control changed, this is used by the ALSA core to generate
events to userspace. tas2562_volume_control_put() does not implement
this, it just writes whatever value userspace wrote to the device and
returns 0 regardless of what the previous value was. Fix this by
suppressing writes if the value is unchanged and returning 1 if the
writes succeed.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260715-asoc-tas2562-put-retval-v1-2-97bf467c924e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
tas2562_volume_control_put() does not do any validation of the control
value written by userspace, it uses it to look up a value in a fixed
size array which can easily be overflowed and then writes whatever value
it gets back to the device. Add validation that we are loading a value
we have in the array.
Cc: stable@vger.kernel.org
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260715-asoc-tas2562-put-retval-v1-1-97bf467c924e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Haidar Lee <haidar.lee@adlinktech.com> says:
The 'Digital Volume Control' added in v5.7 has never worked correctly:
the driver writes the 32-bit DVC coefficient LSB first, but the device
latches the whole coefficient on the write to the last byte (DVC_CFG4),
so every volume change applies a mix of the previous coefficient's
upper bytes and the new LSB. Depending on the sequence of values this
mutes the output entirely or plays at full volume regardless of the
requested level.
Debugged on a TAS2562 (ADLINK OSM-520 / MT8189): traced the I2C writes
with ftrace to confirm the driver writes the intended bytes, then
reproduced both behaviours by writing the same coefficients manually in
each byte order. Patch 1 fixes the write order; patch 2 fixes two wrong
entries in the volume lookup table found while debugging this.
Link: https://patch.msgid.link/20260715-tas2562-dvc-fix-v1-0-072b13901b20@adlinktech.com
The float_vol_db_lookup table is supposed to hold
round(10^(dB/20) * 2^30) for every 2 dB step from -110 dB to 0 dB,
which is 56 entries, but it only has 55: the -90 dB entry duplicates
the -92 dB value (0x0000695b) and the -20 dB entry (0x06666666) is
missing altogether. As a result every step between -90 dB and -22 dB
is off by 2 dB, and the control's maximum raw value of 110 indexes one
element past the end of the array.
Replace the duplicated -90 dB entry with the correct value 0x000084a3
and add the missing -20 dB entry, bringing the table to the full 56
entries so index 55 (raw value 110, 0 dB) is in range again.
Fixes: bf726b1c86 ("ASoC: tas2562: Add support for digital volume control")
Cc: stable@vger.kernel.org
Signed-off-by: Haidar Lee <haidar.lee@adlinktech.com>
Link: https://patch.msgid.link/20260715-tas2562-dvc-fix-v1-2-072b13901b20@adlinktech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TAS2562 applies the 32-bit digital volume coefficient to the
playback path when the last byte, DVC_CFG4 (book 0 page 2 reg 0x0F), is
written. tas2562_volume_control_put() wrote DVC_CFG4 first and DVC_CFG1
(the MSB) last, so every volume change latched a value made of the
previous coefficient's upper three bytes combined with the new LSB; the
remaining bytes only took effect on the next volume change.
In practice the control was unusable: the first setting after power-on
always played at roughly 0 dB no matter what value was requested (the
chip's default upper bytes were still latched), and most subsequent
changes muted the output entirely or produced a distorted, over-unity
gain.
Verified on a TAS2562 (ADLINK OSM-520 / MT8189 board) by tracing the
I2C writes with ftrace and by writing the same coefficients manually in
both byte orders: written MSB-first the register block behaves exactly
as the driver expects, LSB-first reproduces the broken behaviour.
Write the bytes MSB first with DVC_CFG4 last so the complete new
coefficient is latched atomically.
Fixes: bf726b1c86 ("ASoC: tas2562: Add support for digital volume control")
Cc: stable@vger.kernel.org
Signed-off-by: Haidar Lee <haidar.lee@adlinktech.com>
Link: https://patch.msgid.link/20260715-tas2562-dvc-fix-v1-1-072b13901b20@adlinktech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In cs35l56_init() use complete_all() to signal init_completion instead
of complete().
cs35l56_init() was signaling init_completion using the complete() function.
This only releases ONE waiter.
If cs35l56_component_probe() was called multiple times the first time
would consume that one signal, then future calls would timeout waiting for
the completion. This could happen if:
- The component is probed, removed, then probed again without the cs35l56
module being removed.
- A call to component_probe() returns an error and ASoC calls it again
later.
It should use complete_all() so that after it has been signaled it will
allow any code that waits on it to continue immediately.
The one case where the driver must wait for initialization to run again is
when waiting for a reboot after firmware download, and here the code
correctly calls reinit_completion() first.
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260716132045.1469156-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On I2C/SPI call cs35l56_init() before calling
snd_soc_register_component() to prevent the potential for a deadlock
on init_completion.
For most buses all the hardware would be ready when probe() returns,
but on SoundWire, probe() must return before the SoundWire bus driver
will enumerate the device. All access to the registers must be deferred
until the driver receives an ATTACHED notification. But anything that
could return -EPROBE_DEFER must be called during probe, and that includes
snd_soc_register_component(). Because of that, on SoundWire the ASoC
component can be created before the registers are accssible, so
cs35l56_component_probe() waits for init_completion to signal that the
registers are accessible.
On I2C/SPI this 2-stage startup isn't required so their probe()
functions simply called cs35l56_common_probe() and then cs35l56_init().
The problem with this was that snd_soc_register_component() was still
called early. If this triggered ASoC to create the card, ASoC would call
cs35l56_component_probe() which waits on init_completion - but this would
be running inside the cs35l56 driver probe() so blocking it from reaching
the code that signals init_completion, causing a deadlock.
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Reported-by: Salman S. Tahir <salman.abusaad@gmail.com>
Closes: https://lore.kernel.org/linux-sound/95c21574-97d5-4311-9263-9e174d22d22c@opensource.cirrus.com/T/#u
Tested-by: Salman S. Tahir <salman.abusaad@gmail.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260716132045.1469156-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fs210x driver currently puts the regmap cache into cache only mode
during suspend but at no point does it make it writable again, meaning
that device can't work after suspend other than basic powerup which
bypasses the cache.
Mark the cache as writable again when we resync the registers, it's not
clear to me that the cache only mode is needed at all but this is a
fairly minimal change. Since this is setting a flag it's safe to do
even if the cache was not previously in cache only mode.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260715-asoc-fs210x-fix-resume-v1-1-dd81d9c62c05@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The bt-sco-pcm-wb DAI uses the same stream_name strings as bt-sco-pcm
("Playback" and "Capture"). This causes duplicate DAPM AIF widget
names within the same component, leading to debugfs warnings:
debugfs: 'Playback' already exists in 'dapm'
debugfs: 'Capture' already exists in 'dapm'
Give the wideband DAI distinct stream names ("WB Playback" and
"WB Capture") and add corresponding DAPM AIF widgets and routes for
them.
Fixes: 5947e1b499 ("ASoC: bt-sco: extend rate and add a general compatible string")
Assisted-by: VeroCoder:claude-sonnet-4-5
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/20260715100620.1387159-1-shengjiu.wang@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TAS2781 firmware parser reads several variable-length description
strings with strlen() before checking that the string terminator is
present inside the firmware blob. A malformed firmware image without a
NUL terminator can therefore make the parser walk past the end of the
firmware buffer before the later size checks run.
Add a small bounded string-length helper and use it for all description
fields that are parsed from the firmware buffer. Keep the existing size
checks for the fixed bytes that follow each string.
Fixes: 915f5eadeb ("ASoC: tas2781: firmware lib")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260706144540.93929-1-pengpeng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
In tas2562_parse_dt(), the fallback lookup for the deprecated
"shut-down" GPIO property is broken due to a missing pair of braces.
The code intends to reset sdz_gpio to NULL only when the lookup
returns an error that is not -EPROBE_DEFER (so the driver gracefully
continues without a GPIO). However, without braces the statement:
tas2562->sdz_gpio = NULL;
falls outside the IS_ERR() check and is executed unconditionally
for every path through the if block, including a successful GPIO
lookup.
This means any device using the deprecated 'shut-down' DT property
will always have sdz_gpio == NULL after probe, making the GPIO
completely non-functional.
Fix this by adding the missing braces to scope the NULL assignment
inside the IS_ERR() branch, matching the pattern already used for
the primary 'shutdown' GPIO lookup above.
Fixes: f78a97003b ("ASoC: tas2562: Update shutdown GPIO property")
Signed-off-by: Uday Khare <udaykhare77@gmail.com>
Link: https://patch.msgid.link/20260706153109.10953-1-udaykhare77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if the jack is forced to the microphone mode, it will report
as line in. Correct the report to microphone.
Fixes: fc918cbe87 ("ASoC: cs42l43: Add support for the cs42l43")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260708103430.1395207-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On ThinkPad X1 Carbon Gen 13 (Lunar Lake, RT712-SDCA version VA) the
3.5mm headphone jack is silent after rebooting from Windows.
rt712_sdca_va_io_init() gates rt712_sdca_calibration() on the persisted
vendor SW_CONFIG1 flag, and io_init writes SW_CONFIG1=1 at the end
regardless of whether the calibration succeeded. Across a warm reboot
the codec keeps power, so SW_CONFIG1 stays unchanged, the calibration
may be skipped, and the retained state can be invalid, leaving the
headphone amp disabled.
This patch mimics the reset sequence in rt711-sdca.c, it adds an
rt712_sdca_reset() helper, and calls it from io_init so the codec is
reset before initialization. RT712_PARA_VERB_CTL,
RT712_HIDDEN_REG_SW_RESET and RT712_HDA_LEGACY_RESET_CTL are already
defined but were unused. The reset clears SW_CONFIG1 and the analog
state so rt712_sdca_calibration() runs from a clean state and
completes.
Problem reproducible: boot Windows (headphone is good) -> reboot
to Linux (silent).
The reproducibility may depend on Windows' behaviour.
Signed-off-by: Tianze Shao <shaotianze@outlook.com>
Link: https://patch.msgid.link/TYCPR01MB872223CB999D2099A5E0F58DC4F62@TYCPR01MB8722.jpnprd01.prod.outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A standard set of driver-specific fixes and quirks accumulated since
the merge window:
ASoC:
- SOF: Sanity check to prevent OOB reads
- rsnd: Fix clock leak and double-disable issues with PM
- tas675x: Misc fixes for register fields, etc
- lpass-va-macro: Correct codec version for Qualcomm SC7280
- amd-yc: DMIC quirk for Alienware m15 R7 AMD
Others:
- us144mkii: Fix a UAF on disconnect and anchor list corruption
- HD-audio: Realtek quirks for HP models
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmpKCqgOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE+lgBAAk83zPbT+2y7L7GewxT2QTwOj5WMudl6q9RBp
sDfT8sabkVGs68IoWBVijn6H8n7Jy9V9OVqm+I1j/53mcQl4haLiW+Uk0hcOlN1N
UOySZLQusv+UOM7eVOpfvfb+rdx0MiGOr3NZeFD5tyIfhcMjhJ0NRDFHUDu1W3YU
7BRCOqX1xchsYAnGEdI/otb1d2rEHlg4bRUYMqanfOO1mAayfd2kw3RkVlEF4dW9
+8SoVdxWNOueIuq1WWU3DI/nE5Lq0la3ZsHulKTVkfKW3wlBsFhbk5tbWPBC123o
odz71gpoM1wNM10ANWniJoZ3FlUSvKc2N3gJfKgYVp/EWSzFAp01BYpqm4JA8Iq7
EAX7vNj+4wA4HMZYg20vGaj9dekZ15jrro9Xy8sg1+8TSC377xIpXBo1WA470YrS
/B1UCvhhaYmao0tTTsChaDEcBI0OWgS+OagWDijPz8ASwskNOczVeBhE4HxgHidd
eq4IqXcK+qakTcNc6d8AdFdOog8PekUqE+ZaSPkrW7P/QIYKgWEAXfpu0f2IaK8k
3S15xQAg4dvkGAz4+vOWvZfJSP1P1xRabuSNftEgZk8UvlAoIwMZSuoB7uazt61n
4La6BdPHiY//qmco9rV310YHYQE6uISFEPgs0xxKAHWYeTNRfhACDClm8U905Jo2
LZH9c5g=
=eXcj
-----END PGP SIGNATURE-----
Merge tag 'sound-7.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A standard set of driver-specific fixes and quirks accumulated since
the merge window:
ASoC:
- SOF: Sanity check to prevent OOB reads
- rsnd: Fix clock leak and double-disable issues with PM
- tas675x: Misc fixes for register fields, etc
- lpass-va-macro: Correct codec version for Qualcomm SC7280
- amd-yc: DMIC quirk for Alienware m15 R7 AMD
Others:
- us144mkii: Fix a UAF on disconnect and anchor list corruption
- HD-audio: Realtek quirks for HP models"
* tag 'sound-7.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: rsnd: src: Add missing scu_supply clock to suspend/resume
Documentation: sound: tas675x: Fix temperature range and impedance documentation
ASoC: codecs: tas675x: Fix CHx temperature range register bit fields
ASoC: codecs: tas675x: use READ_ONCE for params to be used concurrently
ASoC: rsnd: adg: make rsnd_adg_clk_control() idempotent
ASoC: SOF: validate probe info element counts
ALSA: usx2y: us144mkii: fix work UAF on disconnect
ASoC: amd: yc: Add Alienware m15 R7 AMD to DMIC quirk table
ALSA: hda/realtek: Add quirk for HP Victus 16-e0xxx (88EE) to enable mute LED
MAINTAINERS: ASoC: SOF: add AMD reviewer for Sound Open Firmware
ASoC: codecs: lpass-va-macro: Fix LPASS Codec Version for SC7280
ALSA: us144mkii: capture_urb_complete: redundant usb_anchor_urb corrupts anchor list on each resubmission
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Sen Wang <sen@ti.com> says:
Few miscellaneous bug fixes after the initial merge of TAS675x driver, of
which includes:
- Adding READ_ONCE for all concurrent read params
- Corrected kcontrol bits for temperature range
- Corrected conversion notes in the driver documentation
Link: https://patch.msgid.link/20260630183126.2588322-1-sen@ti.com
The initial merged patch mixed up the bits for temp reg with LDG report,
now fixing to the right bits according to TRM (SLOU589A).
Fixes: 133c81f844 ("ASoC: codecs: Add TAS67524 quad-channel audio amplifier driver")
Signed-off-by: Sen Wang <sen@ti.com>
Link: https://patch.msgid.link/20260630183126.2588322-3-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
active_playback_dais and active_capture_dais are written atomically via
set_bit()/clear_bit() and can be read concurrently from the
fault_check_work delayed work handler.
fault_check_work already uses READ_ONCE; extend the same guard to all other
reads in tas675x_hw_params() and tas675x_mute_stream().
Fixes: 133c81f844 ("ASoC: codecs: Add TAS67524 quad-channel audio amplifier driver")
Signed-off-by: Sen Wang <sen@ti.com>
Link: https://patch.msgid.link/20260630183126.2588322-2-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to both the static definition in downstream...
yupik-audio-overlay.dtsi: qcom,bolero-version = <4>;
#define BOLERO_VERSION_2_0 0x0004)
and the runtime detection:
CDC_VA_TOP_CSR_CORE_ID_0=0x1
CDC_VA_TOP_CSR_CORE_ID_1=0xf
SC7280 has LPASS Codec Version 2.0 and not, as declared with
sm8250_va_data LPASS_CODEC_VERSION_1_0.
Create new va_macro_data with .version not set to use the runtime
detection and correctly get .version = LPASS_CODEC_VERSION_2_0.
Fixes: 77212f300b ("ASoC: codecs: lpass-va-macro: set the default codec version for sm8250")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20260526-sc7280-va-macro-2-0-v1-1-2c1b572fa388@fairphone.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We've got a good collection of device specific fix here, plus a couple
of stand out things:
- Richard fixed some special cases with the new device_link creation
by more gracefully handling any errors during creation.
- Charles did some light refactoring of the SoundWire interfaces to
fix some persistent randconfig issues that people kept running into.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmo9XtYACgkQJNaLcl1U
h9CvHAf/asLvScBxUkGKP76NoX7+czVbpfxH+yfJ6qavcOzvi+hqHlIGh/9vpFSW
GENKI/z/g/9x1WRfwODuBdvBvfkvMGfdUKZoly1zpEICML9cDwvTHwh35TkrwVTf
/cSawS/CByv2ppdeoNe4bBTTSqf4PC0tWo3tRHR2f/LTuSAyac+eJp2PGpRoofBn
te//kJBNSOGLBxJuikOcsf6xfHzB5Rnl5QMXEk1wts5Y51NEpx0PixNbQqJ7Zvee
4jGbytul9RlS26QNM6O5qLGiQy3SpECadwvtMUiYW3jn8/YtSbl760sCeGQXjaRE
7AXiqTVbFRktJ0ffg25eeD4twOE2dQ==
=NKjz
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v7.2-merge-window' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v7.2
We've got a good collection of device specific fix here, plus a couple
of stand out things:
- Richard fixed some special cases with the new device_link creation
by more gracefully handling any errors during creation.
- Charles did some light refactoring of the SoundWire interfaces to
fix some persistent randconfig issues that people kept running into.
If sclk is not provided the driver falls back to using bclk and prints
an info message in the system log. Under normal operations the message
is repeated many times:
[ 17.929576] pcm512x 0-004c: No SCLK, using BCLK: -2
[ 17.949172] pcm512x 0-004c: No SCLK, using BCLK: -2
[ 17.953029] pcm512x 0-004c: No SCLK, using BCLK: -2
[ 17.965059] pcm512x 0-004c: No SCLK, using BCLK: -2
[ 82.592980] pcm512x 0-004c: No SCLK, using BCLK: -2
[ 82.866293] pcm512x 0-004c: No SCLK, using BCLK: -2
Switch from dev_info to dev_info_once to reduce log noise.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://patch.msgid.link/20260625122811.4056274-1-christianshewitt@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In linux-firmware commit from 2026-05-19 `2f90f4fe5c67f51a8410907a...`
`ASoC: tas2783: Add Firmware files for tas2783A projects` by Baojun Xu
138 new firmware files for tas2783 were added, none of which are loaded
by the kernel. Kernel expects files to be named with the following
convention: "%04X-%1X-%1X.bin". However the added firmware files follow
"-0x%1X.bin" naming instead with `0x` hex prefix, which fails to load
resulting in following dmesg log:
slave-tas2783 sdw:0:1:0102:0000:01:8: Direct firmware load for 1714-1-8.bin failed with error -2
slave-tas2783 sdw:0:1:0102:0000:01:8: Failed to read fw binary 1714-1-8.bin
slave-tas2783 sdw:0:1:0102:0000:01:b: Direct firmware load for 1714-1-B.bin failed with error -2
slave-tas2783 sdw:0:1:0102:0000:01:b: Failed to read fw binary 1714-1-B.bin
slave-tas2783 sdw:0:1:0102:0000:01:8: error playback without fw download
slave-tas2783 sdw:0:1:0102:0000:01:8: ASoC error (-22): at snd_soc_dai_hw_params() on tas2783-codec
This same commit removes all 22 symlinks from WHENCE, that used naming
without the '0x' prefix to only 6 prevoiusly existing .bin files.
This patch adds `0x` prefix explicitly to the generated firmware name
allowing file to successfully load. In case prefixed firmware is missing
due to out of date linux-firmware, we set the fallback flag and attempt
to load firmware again based on the old file names.
This prefix change results in functioning firmware loading on ASUS
ProArt PX13 HN7306EAC, which uses 1714-1-0x8.bin and 1714-1-0xB.bin
firmware files.
Tested on top of 7.1 and next-20260619 with SND_SOC_AMD_ACP7X set to no.
Signed-off-by: Bartosz Juraszewski <bjuraszewski@gmail.com>
Link: https://patch.msgid.link/20260622182733.23947-1-bjuraszewski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the core no longer calls this debug helper add it back to the drivers
that originally called it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260623101814.24044-6-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the core no longer calls this debug helper add it back to the drivers
that originally called it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260623101814.24044-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the core no longer calls this debug helper add it back to the drivers
that originally called it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260623101814.24044-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the core no longer calls this debug helper add it back to the drivers
that originally called it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260623101814.24044-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adjusts several default settings to ensure
the speaker protection function can be enabled safely.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://patch.msgid.link/20260615091012.718168-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The datasheet documents that when the PLL is disabled and dual-rate mode
is enabled, only Q values {4, 8, 9, 12, 16} are valid for the CLKDIV
bypass path; all other Q values produce invalid bitclock output.
The existing loop iterates Q from 2 to 17 without this restriction,
causing silent audio failure when an out-of-spec Q is picked.
Restrict the Q search to the allowed set in dual-rate mode.
Fixes: 4f9c16ccfa ("[ALSA] soc - tlv320aic3x - revisit clock setup")
Suggested-by: Mir Jeffres <m-jeffres@ti.com>
Signed-off-by: Sen Wang <sen@ti.com>
Link: https://patch.msgid.link/20260616233322.873081-1-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's been quite a lot of framework improvements this time around,
though mainly cleanups and robustness rather than user visible features.
The same pattern is seen with a lot of the driver work that's going on,
there are new features but a huge proportion of this is bug fixing and
cleanup work. We also have a good selectio of new device support.
- Improvements to SDCA jack handling from Charles Keepax.
- Use of device links to make suspend handling more robust from Richard
Fitzgerald.
- Use of a new helper to factor out a common pattern in SoundWire
enmeration from Charles Keepax.
- Slimming down of the component from Kuninori Morimoto.
- Simplification of format auto selection from Kuninori Morimoto.
- Lots of conversions to guard() from Bui Duc Phuc.
- Addition of a simple-amplifier driver supporting more featureful GPIO
controller amplifiers than the previous basic driver from Herve
Codina.
- Support for AMD ACP 7.x, Cirrus Logic CS42448/CS42888, Everest Semi
ES9356, Mediatek MT2701 and MT8196, Renesas RZ/G3E, Spacemit K3,
Texas Instruments TAC5xx2 and TAS67524.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmov9IgACgkQJNaLcl1U
h9BOYQf/fLQJlwAIQJu540syYQL9N7Lz/+6f41WEAeF86npaz1wvggwX7rWsOlCB
f+6bGiQ/QvYGrDlKBoIRvbrcUosYo5RcPveBhLUeYQ6w2wyhYR5bjF77YMFHHIWm
h+8wG4Cf59SnAvQ2sdctcKgaCbnJgN8IfTIhdGDQwDi2vf9AUO7o4pfKXO/wligq
4vBeuFLM+WgU5x0VhvwIU6yfa8MGSMvf/oX0bn3xYjOp2LyHzdfRGvoY/wa+6pFd
9QX2QsU6Yjrt5/zvuENwOq+nb3NbdDDqdQK8PRDnzYsbhpFj1RA5XRVShhk89h3F
TZyRqht++Vfs0b3CNW1Q59XZgxNX8A==
=3lzj
-----END PGP SIGNATURE-----
Merge tag 'asoc-v7.2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v7.2
There's been quite a lot of framework improvements this time around,
though mainly cleanups and robustness rather than user visible features.
The same pattern is seen with a lot of the driver work that's going on,
there are new features but a huge proportion of this is bug fixing and
cleanup work. We also have a good selectio of new device support.
- Improvements to SDCA jack handling from Charles Keepax.
- Use of device links to make suspend handling more robust from Richard
Fitzgerald.
- Use of a new helper to factor out a common pattern in SoundWire
enmeration from Charles Keepax.
- Slimming down of the component from Kuninori Morimoto.
- Simplification of format auto selection from Kuninori Morimoto.
- Lots of conversions to guard() from Bui Duc Phuc.
- Addition of a simple-amplifier driver supporting more featureful GPIO
controller amplifiers than the previous basic driver from Herve
Codina.
- Support for AMD ACP 7.x, Cirrus Logic CS42448/CS42888, Everest Semi
ES9356, Mediatek MT2701 and MT8196, Renesas RZ/G3E, Spacemit K3,
Texas Instruments TAC5xx2 and TAS67524.
