The ITE controller behind the keyboard of the Lenovo Yoga Slim 7x Gen 11
(048d:83db) carries out a reset but never raises the interrupt that
acknowledges it. i2c_hid_finish_hwreset() therefore waits out its full
one second timeout and logs "device did not ack reset within 1000 ms" on
every probe and every resume, before the keyboard comes up regardless.
Set I2C_HID_QUIRK_NO_IRQ_AFTER_RESET for it, as is already done for
several other ITE parts, so the reset is followed by a fixed 100 ms sleep
instead.
Signed-off-by: Oleg Keri <okerixx@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The headset reports connection and battery status on HID interface
5. When the device is disconnected, ignore incoming battery
reports as they will incorrectly report battery level 0.
Clamp overreported battery values to 100% and add USB ID 1038:12ad
to the driver's device tables.
Signed-off-by: Erik Håkansson <erikhakan@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The SDINNOVATION gaming keyboard (USB ID 36ae:feab) stops reporting
input events after its RGB lighting mode is switched about twice.
Disabling USB autosuspend and unbinding the other HID interfaces make
no difference; the issue does not occur on Windows.
HID_QUIRK_ALWAYS_POLL alone resolves it, verified on 7.1.8 via
usbhid.quirks=0x36ae:0xfeab:0x400.
Reported-by: Marco Carvalho <marcocarvalho.web@gmail.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2514627
Cc: stable@vger.kernel.org
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Cirque touchpads with PID D0C1 generate an error when probed
by the I2C HID driver, resulting in no hidraw device created.
Adding I2C_HID_QUIRK_NO_IRQ_AFTER_RESET fixes the issue.
Signed-off-by: Vadim Klishko <vadim@cirque.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
- initial support for 2026 Steam Controller (Vicki Pfau)
- support for sensor events on the 2025 Steam Controller (Vicki Pfau)
- assorted fixes, improvements and code refactoring (Vicki Pfau)
This brings support for the 2026 Steam Controller, comparably featureful to
the existing support for the Steam Deck.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Adds configuration HID driver for the MSI Claw series of handheld PC's.
In this initial patch add the initial driver outline and attributes for
changing the gamepad mode, M-key behavior, and add a WO reset function.
Sending the SWITCH_MODE and RESET commands causes a USB disconnect in
the device. The completion will therefore never get hit and would trigger
an -EIO. To avoid showing the user an error for every write to these
attrs a bypass for the completion handling is introduced when timeout ==
0.
The initial version of this patch was written by Denis Benato, which
contained the initial reverse-engineering and implementation for the
gamepad mode switching. This work was later expanded by Zhouwang Huang
to include more gamepad modes. Finally, I refactored the drivers data
in/out flow and overall format to conform to kernel driver best
practices and style guides. Claude was used as an initial reviewer of
this patch.
Assisted-by: Claude:claude-sonnet-4-6
Co-developed-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Co-developed-by: Zhouwang Huang <honjow311@gmail.com>
Signed-off-by: Zhouwang Huang <honjow311@gmail.com>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The tap-to-mute button of the HyperX QuadCast 2 (03f0:07b4) is handled
entirely in the device firmware. The firmware gates the audio internally
but never sends the Telephony "Phone Mute" usage (0x2f) that its own report
descriptor advertises, and it does not touch the UAC feature unit either.
Consequently neither an evdev key event nor an ALSA mixer change is ever
generated, and userspace has no way to learn that the microphone was muted:
desktops keep showing the microphone as live, and conferencing applications
keep displaying an unmuted microphone while transmitting silence.
The mute state is reported through a vendor-defined collection instead:
06 c0 ff Usage Page (Vendor-Defined 0xFFC0)
a1 01 Collection (Application)
06 c1 ff Usage Page (Vendor-Defined 0xFFC1)
85 77 Report ID (0x77)
09 f0 Usage (0xF0)
75 08 95 3f Report Size (8), Report Count (63)
81 02 Input (Data,Var,Abs)
Pressing the button emits a 64-byte report on that collection:
77 06 00 00 ... microphone unmuted
77 06 01 00 ... microphone muted
where byte 1 identifies the mute event and byte 2 carries the resulting
state. As the payload is an opaque vendor blob carrying no HID usages,
hid-input cannot map it and a hwdb entry cannot express it either.
Add a driver that decodes the report and emits KEY_MICMUTE, which makes the
button behave like any other microphone mute key.
Note that the device reports the resulting absolute state, whereas
KEY_MICMUTE is a momentary key that userspace acts on as a toggle, so the
driver emits one keypress per state change.
Tested on a HyperX QuadCast 2 (03f0:07b4).
Signed-off-by: Benjamin Blume <benjaminblume@posteo.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The Arctis Nova 5X, Nova 7 Gen2, and Nova 7 2026 refresh headsets answer
status polls, but also send unsolicited battery and connection updates
on a second HID interface (interface 5). Use that interface through
async_interface so the driver does not have to poll. Add request and
parse helpers for the Nova status format (0xb0/0xb7/0xb9/0xbb opcodes).
The original (pre-Gen2) Arctis Nova 7 family answers the same status
opcodes on the same interfaces, but reports battery capacity as a
discrete 0-4 level instead of a raw percentage. Add a second parse
function that maps that level through steelseries_map_capacity(), and a
separate device_info so the two capacity encodings cannot get mixed up.
Add the fourteen USB product IDs that share these protocols:
0x2253 Arctis Nova 5X
0x2202 Arctis Nova 7
0x2206 Arctis Nova 7X
0x22a4 Arctis Nova 7X (alternate PID)
0x223a Arctis Nova 7 Diablo
0x227a Arctis Nova 7 World of Warcraft Edition
0x22a1 Arctis Nova 7 2026
0x22a7 Arctis Nova 7P 2026
0x22a5 Arctis Nova 7X 2026
0x22a9 Arctis Nova 7 Diablo 2026
0x227e Arctis Nova 7 Gen 2
0x2258 Arctis Nova 7X Gen 2
0x229e Arctis Nova 7X Gen 2 (alternate PID)
0x22ad Arctis Nova 7X Gen 2 (alternate PID)
Signed-off-by: Sriman Achanta <srimanachanta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The SteelSeries Arctis 1 Wireless for Xbox (0x12b6) was labelled as the
plain Arctis 1 Wireless. Rename USB_DEVICE_ID_STEELSERIES_ARCTIS_1 to
USB_DEVICE_ID_STEELSERIES_ARCTIS_1_X, along with the matching quirk flag
and device table entry. The device ID value is unchanged.
Signed-off-by: Sriman Achanta <srimanachanta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The AULA Mini 60 HE Pro wireless keyboard dongle (USB ID
0c45:fefe) becomes unresponsive after roughly one minute of idle.
No error appears in dmesg; the only recovery is physically
replugging the dongle.
This has been reproduced across kernels 6.8, 6.14 and 7.1.3.
Testing shows HID_QUIRK_ALWAYS_POLL alone resolves the issue,
verified via usbhid.quirks=0x0c45:0xfefe:0x400.
Signed-off-by: Yuxiang Lin <mclyxfdw@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The ASUS Zenbook A16 (UX3607OA), a Qualcomm Snapdragon X2 Elite Extreme
(Glymur)-based laptop, carries its main keyboard on an I2C-HID device
with the ID 0B05:4B42. Its Fn/media hotkeys are emitted as vendor-page
(HID_UP_ASUSVENDOR) usages on report 0x5A.
Match the device in hid-asus with the standard I2C keyboard quirks and
add the three usage mappings observed on the hardware:
0x85 -> KEY_CAMERA (Fn+F11, camera toggle)
0x86 -> KEY_PROG1 (Fn+F12, MyASUS key)
0x5f -> KEY_PROG2 (extra programmable key)
The camera-toggle key reports its usage (0x85) together with a companion
state byte in the same array report ("5a 85 01" / "5a 85 10"). The 0x10
companion aliases the brightness-down vendor usage and spuriously dims
the panel, so add QUIRK_FILTER_CAMERA_COMPANION to zero the companion
slots for this device before input mapping. The quirk is device-gated so
no other ASUS model is affected.
Assisted-by: Claude Code:claude-opus-4-8
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The BTP-KP20D dongle in Direct/HID mode (20dd:5159) re-enumerates every
few seconds because usbhid never submits its interrupt-IN URB: no HID
driver binds to the vendor-specific report descriptor, so the device is
never opened, and the firmware treats the idle endpoint as a lost link.
Add HID_QUIRK_ALWAYS_POLL to keep the interrupt-IN URB submitted from
probe time.
Signed-off-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The Logitech G915 TKL has a lightspeed receiver with a product id of
0xc545. This receiver seems to behave like 0xc547 receiver.
Add a definition for this new receiver id and a mapping for the
recvr_type_gaming_hidpp_ls_1_3 type, the receiver now reports battery
status of the connected keyboard.
Signed-off-by: Colin Blower <colin@1101b.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The MSI Raider A18 HX A9WJG exposes two internal SteelSeries USB HID
devices for RGB lighting: KLC (1038:1122) for the keyboard and ALC
(1038:1161) for the lightbar/logo zones.
Add DMI-gated support for these devices and expose them as multicolor
LED class devices. The driver sends the same HID class SET_REPORT
control transfer as the tested userspace implementation for this
machine and writes a uniform RGB value to all known keyboard keys or
ALC zones.
The ALC payload uses sparse LED IDs on this chassis: 0x00, 0x01,
0x02 and 0x03 are physical zones, while 0x04 and 0x05 do not appear
to map to physical LEDs. Unused payload LED ID slots are initialized
to 0xff so they are ignored by the controller instead of defaulting
to LED ID 0x00.
Limit RGB support to USB interface 0 and the tested DMI system because
the KLC product ID is shared across MSI laptop designs and the key
layout mapping is model-specific. If the DMI or interface check does
not match, keep the device bound as a regular HID device instead of
failing probe.
Also make the existing Arctis 9 vendor usage-page check defensive by
returning false for report descriptors shorter than three bytes before
inspecting hdev->rdesc[0..2].
Tested on MSI Raider A18 HX A9WJG. Both internal SteelSeries ALC
(1038:1161) and KLC (1038:1122) HID devices bind on interface 0 and
create steelseries::lightbar and steelseries::kbd_backlight. Setting
multi_intensity and brightness changes the keyboard and lightbar
colors.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202606010709.X0QYNjFZ-lkp@intel.com/
Signed-off-by: David Glushkov <david.glushkov@sntiq.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Add support for the HORI Wireless Switch Pad (vendor 0x0f0d, product
0x00f6), a licensed third-party Nintendo Switch Pro Controller.
The controller reports controller type 0x06 (vs 0x03 for first-party
Pro Controllers) and has the following quirks:
- SPI flash calibration data is incompatible; use default stick
calibration values instead.
- X and Y button bits are swapped compared to first-party controllers;
add a dedicated button mapping table.
- Rumble and IMU enable may timeout (no vibration motor in hardware);
treat as non-fatal for licensed controllers.
Tested over Bluetooth on NixOS with kernel 7.0.5 and 7.0.10:
- All 14 buttons map correctly
- Player LED sets on connect
- Sticks report correctly with default calibration
- IMU/gyro data streams at 60Hz
- D-pad reports on ABS_HAT0X/HAT0Y
Device information:
Bluetooth name: Lic Pro Controller
Bluetooth HID: 0005:0F0D:00F6
Assisted-by: Kiro:Auto [Amazon Kiro IDE]
Signed-off-by: Hector Zelaya <hector@hectorzelaya.dev>
Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Add USB ID support for the ThinkPad X13 detachable keyboard.
The Keyboard uses the same HID raw event protocol as the ThinkPad
X12 Gen 2. The functionality stays the same with X12 Gen 2 Keyboards.
Also declare KEY_PERFORMANCE capability in lenovo_input_configured()
for X13 detachable, allowing userspace to discover the key via evdev
capability bits.
Signed-off-by: Vishnu Sankar <vishnuocv@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The pen setup for this device uses bluetooth for
communicating battery levels and status instead of
reporting it over i2c.
Without this quirk, the device either reports an
extra, broken phantom battery, or hangs.
Signed-off-by: Harrison Vanderbyl <harrison.vanderbyl@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The SIGMACHIP USB mouse with VID/PID 1c4f:0034 can disconnect and
re-enumerate repeatedly after it has been enumerated if its interrupt
endpoint is not continuously polled.
This was observed with the device reporting itself as "SIGMACHIP Usb
Mouse". Keeping the input event device open avoids the disconnects.
Add HID_QUIRK_ALWAYS_POLL for this device so the HID core keeps polling
it even when there is no userspace input consumer.
Cc: stable@vger.kernel.org
Signed-off-by: hlleng <a909204013@gmail.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The BLTP7853 I2C HID touchpad may fail to probe after reboot or
reprobe because reset completion is not signalled to the host. The
driver then waits for the reset-complete interrupt until it times out
and the device probe fails:
i2c_hid i2c-BLTP7853:00: failed to reset device.
i2c_hid i2c-BLTP7853:00: can't add hid device: -61
i2c_hid: probe of i2c-BLTP7853:00 failed with error -61
Add I2C_HID_QUIRK_NO_IRQ_AFTER_RESET for the device so i2c-hid does
not wait for a reset interrupt that may never arrive.
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Adds support for the second generation of RGB Control for OneXPlayer
devices. The interface mirrors the first generation, with some
differences to how messages are formatted.
Some devices have both a GEN1 MCU for RGB control and a GEN2 MCU for
button mapping. To avoid conflicts, quirk these devices to skip RGB
setup for the GEN2_USAGE_PAGE.
Reviewed-by: Zhouwang Huang <honjow311@gmail.com>
Tested-by: Zhouwang Huang <honjow311@gmail.com>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Adds OneXPlayer HID configuration driver. In this initial driver patch,
add the RGB interface for the first generation of HID based RGB control.
This interface provides the following attributes:
- brightness: provided by the LED core, this works in a fairly unique
way on this device. The hardware accepts 5 brightness values (0-4),
which affects the brightness of the multicolor and animated effects
built into the MCU firmware. For monocolor settings, the device
expects the hardware brightness value to be pushed to maximum, then we
apply brightness adjustments mathematically based on % (0-100). This
leads to some odd conversion as we need the brightness slider to reach
the full range, but it has no affect when incrementing between the
division points for other effects.
- multi-intensity: provided by the LED core for red, green, and blue.
- effect: Allows the MCU to set 19 individual effects.
- effect_index: Lists the 19 valid effect names for the interface.
- enabled: Allows the MCU to toggle the RGB interface on/off.
- enabled_index: Lists the valid states for enabled.
- speed: Allows the MCU to set the animation rate for the various
effects.
- speed_range: Lists the valid range of speed (0-9).
The MCU also has a few odd quirks that make sending multiple synchronous
events challenging. It will essentially freeze if it receives another
message before it has finished processing the last command. It also will
not reply if you wait on it using a completion. To get around this, we
do a 200ms sleep inside a work queue thread and debounce all but the most
recent message using a 50ms mod_delayed_work. This will cache the last
write, queue the work, then return so userspace can release its write
thread. The work queue is only used for brightness/multi-intensity as
that is the path likely to receive rapid successive writes.
Reviewed-by: Zhouwang Huang <honjow311@gmail.com>
Tested-by: Zhouwang Huang <honjow311@gmail.com>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The Rakk Dasig X gaming mouse has a faulty HID report descriptor that
declares USAGE_MAXIMUM=3 (buttons 1-3) while actually sending 5 button
bits (REPORT_COUNT=5). This causes the kernel to ignore side buttons
(buttons 4 and 5).
Fix by patching the descriptor to set USAGE_MAXIMUM=5 in the
report_fixup callback.
The mouse uses Telink vendor ID 0x248a with three product IDs for USB
direct (0xfb01), wireless dongle (0xfa02), and Bluetooth (0x8266)
connection modes. All three variants have the same bug at byte offset 17.
Suggested-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Signed-off-by: Karl Cayme <kcayme@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Elan SB974D touchpad uses ELAN_MT_I2C format to send HID reports. Add an
entry to match for the device and parse its vendor specific format.
Signed-off-by: Damien Dejean <damiendejean@google.com>
Signed-off-by: Kornel Dulęba <korneld@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When the Huawei CD30 USB keyboard undergoes 500 reboot cycles,
initialization may fail due to a report descriptor problem.
The error log is as follows:
[pid:175,cpu0,kworker/0:1,6]usb 1-1.2.2: new low-speed USB device number 6 using xhci-hcd
[pid:175,cpu0,kworker/0:1,9]usb 1-1.2.2: New USB device found, idVendor=12d1, idProduct=109b, bcdDevice= 1.03
[pid:175,cpu0,kworker/0:1,0]usb 1-1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[pid:175,cpu0,kworker/0:1,1]usb 1-1.2.2: Product: HUAWEI USB Wired Keyboard
[pid:175,cpu0,kworker/0:1,2]usb 1-1.2.2: Manufacturer: HUAWEI
[pid:175,cpu0,kworker/0:1,4]input: HUAWEI HUAWEI USB Wired Keyboard as /devices/platform/efc00000.hisi_usb/efc00000.dwc3/xhci-hcd.1.auto/usb1/1-1/1-1.2/1-1.2.2/1-1.2.2:1.0/0003:12D1:109B.0002/input/input6
[pid:175,cpu0,kworker/0:1,5]hid-generic 0003:12D1:109B.0002: input,hidraw1: USB HID v1.10 Keyboard [HUAWEI HUAWEI USB Wired Keyboard] on usb-xhci-hcd.1.auto-1.2.2/input0
[pid:175,cpu0,kworker/0:1,9]hid-generic 0003:12D1:109B.0003: collection stack underflow
[pid:175,cpu0,kworker/0:1,0]hid-generic 0003:12D1:109B.0003: item 0 0 0 12 parsing failed
[pid:175,cpu0,kworker/0:1,1]hid-generic: probe of 0003:12D1:109B.0003 failed with error -22
...
When encountering such a situation, fix it with the correct report descriptor.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This patch adds support for the following instruments:
* Rock Band 1/2/3 Wii/PS3 instruments
* Rock Band 3 PS3 Pro instruments
* DJ Hero Turntable
Wii and PS3 instruments are the same besides the vendor and product ID.
This patch also fixes the mappings for the existing Guitar Hero
instruments.
Co-developed-by: Sanjay Govind <sanjay.govind9@gmail.com>
Signed-off-by: Sanjay Govind <sanjay.govind9@gmail.com>
Co-developed-by: Brenton Simpson <appsforartists@google.com>
Signed-off-by: Brenton Simpson <appsforartists@google.com>
Signed-off-by: Rosalie Wanders <rosalie@mailbox.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Apparently this same protocol is used by more mice from different brands.
This patch adds support for the VXE Dragonfly R1 Pro.
Tested-by: Dominykas Svetikas <dominykas@svetikas.lt>
Signed-off-by: Lode Willems <me@lodewillems.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
According to a mailing list report [1], this controller's predecessor
has the same issue. However, it uses the xpad driver instead of HID, so
this quirk wouldn't apply.
[1]: https://lore.kernel.org/linux-input/unufo3$det$1@ciao.gmane.io/
Signed-off-by: leo vriska <leo@60228.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Drop the Asus UX550* touchscreen ignore battery quirks, there is a blanket
HID_BATTERY_QUIRK_IGNORE for all USB_VENDOR_ID_ELAN USB touchscreens now,
so these are just a duplicate of those.
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
XG mobile station 2022 has a different PID than the 2023 model: add it
that model to hid-asus.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Adds initial framework for a new HID driver, hid-lenovo-go-s, along with
a uevent to report the firmware version for the MCU.
This driver primarily provides access to the configurable settings of the
Lenovo Legion Go S controller. It will attach if the controller is in
xinput or dinput mode. Non-configuration raw reports are forwarded to
ensure the other endpoints continue to function as normal.
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Co-developed-by: Ethan Tidmore <ethantidmore06@gmail.com>
Signed-off-by: Ethan Tidmore <ethantidmore06@gmail.com>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Adds initial framework for a new HID driver, hid-lenovo-go, along with
attributes that report the firmware and hardware version for each
component of the HID device, of which there are 4 parts: The MCU, the
transmission dongle, the left "handle" controller half, and the right
"handle" controller half. Each of these devices are provided an attribute
group to contain its device specific attributes. Additionally, the touchpad
device attributes are logically separated from the other components in
another attribute group.
This driver primarily provides access to the configurable settings of the
Lenovo Legion Go and Lenovo Legion Go 2 controllers running the latest
firmware. As previously noted, the Legion Go controllers recently had a
firmware update[1] which switched from the original "SepentiaUSB" protocol
to a brand new protocol for the Go 2, primarily to ensure backwards and
forwards compatibility between the Go and Go 2 devices. As part of that
update the PIDs for the controllers were changed, so there is no risk of
this driver attaching to controller firmware that it doesn't support.
--
v6:
- Make attributes static.
- Use NULL instead of 0 in mcu_propery_out when there is no data.
v5:
- Make version attributes static, retrieve them using delayed work
during probe.
- Fix endianness of version strings and print as hex.
v3:
- Add hid-lenovo.c and Mark Pearson to LENOVO HID DRIVERS entry in MAINTAINERS
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
XG mobile stations have the 0x5a endpoint and has to be initialized:
add them to hid-asus.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This patch adds the dongle device IDs for the CRKD Gibson SG
Signed-off-by: Rosalie Wanders <rosalie@mailbox.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Add support for the for the EXC3188 touchscreen from eGalaxy.
Signed-off-by: Thorsten Schmelzer <tschmelzer@topcon.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This commit adds support for the PDP Jaguar and MadCatz Stratocaster.
Signed-off-by: Rosalie Wanders <rosalie@mailbox.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
