mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/
synced 2026-10-28 20:03:05 +00:00
d920a2ed86
SanDisks USB3 storage may disapper after system reboot: usb usb2-port3: link state change xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0 usb usb2-port3: do warm reset, port only xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0 usb usb2-port3: not warm reset yet, waiting 50ms xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0 usb usb2-port3: not warm reset yet, waiting 200ms ... xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0 usb usb2-port3: not warm reset yet, waiting 200ms xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0 xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0 xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0 usb usb2-port3: not enabled, trying warm reset again... This is due to the USB device still cause port change event after xHCI is shuted down: xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001 xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling. xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0 xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling. xhci_hcd 0000:38:00.0: // Halt the HC xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1 xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling. xhci_hcd 0000:00:14.0: // Halt the HC xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203 xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203 xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203 usb 2-3: device not accepting address 2, error -108 xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263 xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1 usb usb2-port3: not reset yet, waiting 60ms ACPI: PM: Preparing to enter system sleep state S5 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1 usb usb2-port3: not reset yet, waiting 200ms reboot: Restarting system The port change event is caused by LPM transition, so disabling LPM at shutdown to make sure the device is in U0 for warmboot. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
History
|
|
|---|---|---|
| .. | ||
| buffer.c | ||
| config.c | ||
| devices.c | ||
| devio.c | ||
| driver.c | ||
| endpoint.c | ||
| file.c | ||
| generic.c | ||
| hcd-pci.c | ||
| hcd.c | ||
| hub.c | ||
| hub.h | ||
| Kconfig | ||
| ledtrig-usbport.c | ||
| Makefile | ||
| message.c | ||
| notify.c | ||
| of.c | ||
| otg_productlist.h | ||
| phy.c | ||
| phy.h | ||
| port.c | ||
| quirks.c | ||
| sysfs.c | ||
| urb.c | ||
| usb-acpi.c | ||
| usb.c | ||
| usb.h | ||