linux/drivers/gpu/drm/panel/panel-simple.c

4599 lines
112 KiB

drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: drop drm_device from drm_panel The panel drivers used drm_panel.drm for two purposes: 1) Argument to drm_mode_duplicate() 2) drm->dev was used in error messages The first usage is replaced with drm_connector.dev - drm_connector is already connected to a drm_device and we have a valid connector The second usage is replaced with drm_panel.dev - this makes drivers more consistent in their dev argument used for dev_err() and friends With these replacements there are no more uses of drm_panel.drm, so it is removed from struct drm_panel. With this change drm_panel_attach() and drm_panel_detach() no longer have any use as they are empty functions. v2: - editorial correction in changelog (Laurent) Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-8-sam@ravnborg.org
2019-12-07 15:03:35 +01:00
drm/panel: drop drm_device from drm_panel The panel drivers used drm_panel.drm for two purposes: 1) Argument to drm_mode_duplicate() 2) drm->dev was used in error messages The first usage is replaced with drm_connector.dev - drm_connector is already connected to a drm_device and we have a valid connector The second usage is replaced with drm_panel.dev - this makes drivers more consistent in their dev argument used for dev_err() and friends With these replacements there are no more uses of drm_panel.drm, so it is removed from struct drm_panel. With this change drm_panel_attach() and drm_panel_detach() no longer have any use as they are empty functions. v2: - editorial correction in changelog (Laurent) Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-8-sam@ravnborg.org
2019-12-07 15:03:35 +01:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: drop drm_device from drm_panel The panel drivers used drm_panel.drm for two purposes: 1) Argument to drm_mode_duplicate() 2) drm->dev was used in error messages The first usage is replaced with drm_connector.dev - drm_connector is already connected to a drm_device and we have a valid connector The second usage is replaced with drm_panel.dev - this makes drivers more consistent in their dev argument used for dev_err() and friends With these replacements there are no more uses of drm_panel.drm, so it is removed from struct drm_panel. With this change drm_panel_attach() and drm_panel_detach() no longer have any use as they are empty functions. v2: - editorial correction in changelog (Laurent) Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-8-sam@ravnborg.org
2019-12-07 15:03:35 +01:00
drm/panel: drop drm_device from drm_panel The panel drivers used drm_panel.drm for two purposes: 1) Argument to drm_mode_duplicate() 2) drm->dev was used in error messages The first usage is replaced with drm_connector.dev - drm_connector is already connected to a drm_device and we have a valid connector The second usage is replaced with drm_panel.dev - this makes drivers more consistent in their dev argument used for dev_err() and friends With these replacements there are no more uses of drm_panel.drm, so it is removed from struct drm_panel. With this change drm_panel_attach() and drm_panel_detach() no longer have any use as they are empty functions. v2: - editorial correction in changelog (Laurent) Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-8-sam@ravnborg.org
2019-12-07 15:03:35 +01:00
drm: Nuke mode->vrefresh Get rid of mode->vrefresh and just calculate it on demand. Saves a bit of space and avoids the cached value getting out of sync with reality. Mostly done with cocci, with the following manual fixups: - Remove the now empty loop in drm_helper_probe_single_connector_modes() - Fix __MODE() macro in ch7006_mode.c - Fix DRM_MODE_ARG() macro in drm_modes.h - Remove leftover comment from samsung_s6d16d0_mode - Drop the TODO @@ @@ struct drm_display_mode { ... - int vrefresh; ... }; @@ identifier N; expression E; @@ struct drm_display_mode N = { - .vrefresh = E }; @@ identifier N; expression E; @@ struct drm_display_mode N[...] = { ..., { - .vrefresh = E } ,... }; @@ expression E; @@ { DRM_MODE(...), - .vrefresh = E, } @@ identifier M, R; @@ int drm_mode_vrefresh(const struct drm_display_mode *M) { ... - if (M->vrefresh > 0) - R = M->vrefresh; - else if (...) { ... } ... } @@ struct drm_display_mode *p; expression E; @@ ( - p->vrefresh = E; | - p->vrefresh + drm_mode_vrefresh(p) ) @@ struct drm_display_mode s; expression E; @@ ( - s.vrefresh = E; | - s.vrefresh + drm_mode_vrefresh(&s) ) @@ expression E; @@ - drm_mode_vrefresh(E) ? drm_mode_vrefresh(E) : drm_mode_vrefresh(E) + drm_mode_vrefresh(E) @find_substruct@ identifier X; identifier S; @@ struct X { ... struct drm_display_mode S; ... }; @@ identifier find_substruct.S; expression E; identifier I; @@ { .S = { - .vrefresh = E } } @@ identifier find_substruct.S; identifier find_substruct.X; expression E; identifier I; @@ struct X I[...] = { ..., .S = { - .vrefresh = E } ,... }; v2: Drop TODO v3: Rebase v4: Rebase Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@siol.net> Cc: Inki Dae <inki.dae@samsung.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: Seung-Woo Kim <sw0312.kim@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: CK Hu <ck.hu@mediatek.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jerry Han <hanxu5@huaqin.corp-partner.google.com> Cc: Icenowy Zheng <icenowy@aosc.io> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: VMware Graphics <linux-graphics-maintainer@vmware.com> Cc: Thomas Hellstrom <thellstrom@vmware.com> Cc: linux-amlogic@lists.infradead.org Cc: nouveau@lists.freedesktop.org Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-4-ville.syrjala@linux.intel.com
2020-04-28 20:19:27 +03:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: drop drm_device from drm_panel The panel drivers used drm_panel.drm for two purposes: 1) Argument to drm_mode_duplicate() 2) drm->dev was used in error messages The first usage is replaced with drm_connector.dev - drm_connector is already connected to a drm_device and we have a valid connector The second usage is replaced with drm_panel.dev - this makes drivers more consistent in their dev argument used for dev_err() and friends With these replacements there are no more uses of drm_panel.drm, so it is removed from struct drm_panel. With this change drm_panel_attach() and drm_panel_detach() no longer have any use as they are empty functions. v2: - editorial correction in changelog (Laurent) Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-8-sam@ravnborg.org
2019-12-07 15:03:35 +01:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: drop drm_device from drm_panel The panel drivers used drm_panel.drm for two purposes: 1) Argument to drm_mode_duplicate() 2) drm->dev was used in error messages The first usage is replaced with drm_connector.dev - drm_connector is already connected to a drm_device and we have a valid connector The second usage is replaced with drm_panel.dev - this makes drivers more consistent in their dev argument used for dev_err() and friends With these replacements there are no more uses of drm_panel.drm, so it is removed from struct drm_panel. With this change drm_panel_attach() and drm_panel_detach() no longer have any use as they are empty functions. v2: - editorial correction in changelog (Laurent) Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Stefan Mavrodiev <stefan@olimex.com> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: "Guido Günther" <agx@sigxcpu.org> Cc: Purism Kernel Team <kernel@puri.sm> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-8-sam@ravnborg.org
2019-12-07 15:03:35 +01:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel-simple: Support hpd-gpios for delaying prepare() People use panel-simple when they have panels that are builtin to their device. In these cases the HPD (Hot Plug Detect) signal isn't really used for hotplugging devices but instead is used for power sequencing. Panel timing diagrams (especially for eDP panels) usually have the HPD signal in them and it acts as an indicator that the panel is ready for us to talk to it. Sometimes the HPD signal is hooked up to a normal GPIO on a system. In this case we need to poll it in the correct place to know that the panel is ready for us. In some system designs the right place for this is panel-simple. When adding this support, we'll account for the case that there might be a circular dependency between panel-simple and the provider of the GPIO. The case this was designed for was for the "ti-sn65dsi86" bridge chip. If HPD is hooked up to one of the GPIOs provided by the bridge chip then in our probe function we'll always get back -EPROBE_DEFER. Let's handle this by allowing this GPIO to show up late if we saw -EPROBE_DEFER during probe. NOTE: since the gpio_get_optional() is used, if the "hpd-gpios" isn't there our variable will just be NULL and we won't do anything in prepare(). Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.3.I53fed5b501a31e7a7fa13268ebcdd6b77bd0cadd@changeid
2020-05-07 14:34:57 -07:00
drm/panel-simple: Support hpd-gpios for delaying prepare() People use panel-simple when they have panels that are builtin to their device. In these cases the HPD (Hot Plug Detect) signal isn't really used for hotplugging devices but instead is used for power sequencing. Panel timing diagrams (especially for eDP panels) usually have the HPD signal in them and it acts as an indicator that the panel is ready for us to talk to it. Sometimes the HPD signal is hooked up to a normal GPIO on a system. In this case we need to poll it in the correct place to know that the panel is ready for us. In some system designs the right place for this is panel-simple. When adding this support, we'll account for the case that there might be a circular dependency between panel-simple and the provider of the GPIO. The case this was designed for was for the "ti-sn65dsi86" bridge chip. If HPD is hooked up to one of the GPIOs provided by the bridge chip then in our probe function we'll always get back -EPROBE_DEFER. Let's handle this by allowing this GPIO to show up late if we saw -EPROBE_DEFER during probe. NOTE: since the gpio_get_optional() is used, if the "hpd-gpios" isn't there our variable will just be NULL and we won't do anything in prepare(). Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.3.I53fed5b501a31e7a7fa13268ebcdd6b77bd0cadd@changeid
2020-05-07 14:34:57 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel-simple: Support hpd-gpios for delaying prepare() People use panel-simple when they have panels that are builtin to their device. In these cases the HPD (Hot Plug Detect) signal isn't really used for hotplugging devices but instead is used for power sequencing. Panel timing diagrams (especially for eDP panels) usually have the HPD signal in them and it acts as an indicator that the panel is ready for us to talk to it. Sometimes the HPD signal is hooked up to a normal GPIO on a system. In this case we need to poll it in the correct place to know that the panel is ready for us. In some system designs the right place for this is panel-simple. When adding this support, we'll account for the case that there might be a circular dependency between panel-simple and the provider of the GPIO. The case this was designed for was for the "ti-sn65dsi86" bridge chip. If HPD is hooked up to one of the GPIOs provided by the bridge chip then in our probe function we'll always get back -EPROBE_DEFER. Let's handle this by allowing this GPIO to show up late if we saw -EPROBE_DEFER during probe. NOTE: since the gpio_get_optional() is used, if the "hpd-gpios" isn't there our variable will just be NULL and we won't do anything in prepare(). Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.3.I53fed5b501a31e7a7fa13268ebcdd6b77bd0cadd@changeid
2020-05-07 14:34:57 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel: simple: add panel-dpi support The panel-dpi compatible is a fallback that allows the DT to specify the timing. When matching panel-dpi expect the device tree to include the timing information for the display-panel. Background for this change: There are a lot of panels and new models hits the market very often. It is a lost cause trying to chase them all and users of new panels will often find them in situations that the panel they ues are not supported by the kernel. On top of this a lot of panels are customized based on customer specifications. Including the panel timing in the device tree allows for a simple way to describe the actual HW and use this description in a generic way in the kernel. This allows uses of proprietary panels, or panels which are not included in the kernel, to specify the timing in the device tree together with all the other HW descriptions. And thus, using the device tree it is then easy to add support for an otherwise unknown panel. The current support expect panels that do not require any delays for prepare/enable/disable/unprepare. Oleksandr Suvorov replied: I've just tested this patch on Apalis iMX6Q and Colibri iMX7D using panel settings from the following patch: https://lore.kernel.org/linux-arm-kernel/20200115123401.2264293-4-oleksandr.suvorov@toradex.com/ It works for me, thanks! Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Tested-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Maxime Ripard <mripard@kernel.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200216181513.28109-6-sam@ravnborg.org
2020-02-16 19:15:13 +01:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel-edp: Split eDP panels out of panel-simple The panel-simple driver handles way too much. Let's start trying to get a handle on it by splitting out the eDP panels. This patch does this: 1. Start by copying simple-panel verbatim over to a new driver, simple-panel-edp. 2. Rename "panel_simple" to "panel_edp" in the new driver. 3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new driver. Remove those panels from the old driver. 4. Remove all recent "DP AUX bus" stuff from the old driver. The DP AUX bus is only possible on DP panels. 5. Remove all DSI / MIPI related functions from the new driver. 6. Remove bus_format / bus_flags from eDP driver. These things don't seem to make any sense for eDP panels so let's stop filling in made up stuff. In the end we end up with a bunch of duplicated code for now. Future patches will try to address _some_ of this duplicated code though some of it will be unavoidable. NOTE: This may not actually move all eDP panels over to the new driver since not all panels were properly marked with `DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward panels I could identify but even so there may be some missed. Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.7.I0a2f75bb822d17ce06f5b147734764eeb0c3e3df@changeid
2021-09-14 13:21:54 -07:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel: simple: add panel-dpi support The panel-dpi compatible is a fallback that allows the DT to specify the timing. When matching panel-dpi expect the device tree to include the timing information for the display-panel. Background for this change: There are a lot of panels and new models hits the market very often. It is a lost cause trying to chase them all and users of new panels will often find them in situations that the panel they ues are not supported by the kernel. On top of this a lot of panels are customized based on customer specifications. Including the panel timing in the device tree allows for a simple way to describe the actual HW and use this description in a generic way in the kernel. This allows uses of proprietary panels, or panels which are not included in the kernel, to specify the timing in the device tree together with all the other HW descriptions. And thus, using the device tree it is then easy to add support for an otherwise unknown panel. The current support expect panels that do not require any delays for prepare/enable/disable/unprepare. Oleksandr Suvorov replied: I've just tested this patch on Apalis iMX6Q and Colibri iMX7D using panel settings from the following patch: https://lore.kernel.org/linux-arm-kernel/20200115123401.2264293-4-oleksandr.suvorov@toradex.com/ It works for me, thanks! Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Tested-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Maxime Ripard <mripard@kernel.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200216181513.28109-6-sam@ravnborg.org
2020-02-16 19:15:13 +01:00
drm/panel: simple: add panel-dpi support The panel-dpi compatible is a fallback that allows the DT to specify the timing. When matching panel-dpi expect the device tree to include the timing information for the display-panel. Background for this change: There are a lot of panels and new models hits the market very often. It is a lost cause trying to chase them all and users of new panels will often find them in situations that the panel they ues are not supported by the kernel. On top of this a lot of panels are customized based on customer specifications. Including the panel timing in the device tree allows for a simple way to describe the actual HW and use this description in a generic way in the kernel. This allows uses of proprietary panels, or panels which are not included in the kernel, to specify the timing in the device tree together with all the other HW descriptions. And thus, using the device tree it is then easy to add support for an otherwise unknown panel. The current support expect panels that do not require any delays for prepare/enable/disable/unprepare. Oleksandr Suvorov replied: I've just tested this patch on Apalis iMX6Q and Colibri iMX7D using panel settings from the following patch: https://lore.kernel.org/linux-arm-kernel/20200115123401.2264293-4-oleksandr.suvorov@toradex.com/ It works for me, thanks! Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Tested-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Maxime Ripard <mripard@kernel.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200216181513.28109-6-sam@ravnborg.org
2020-02-16 19:15:13 +01:00
drm/panel: simple: Add ability to override typical timing This patch adds the ability to override the typical display timing for a given panel. This is useful for devices which have timing constraints that do not apply across the entire display driver (eg: to avoid crosstalk between panel and digitizer on certain laptops). The rules are as follows: - panel must not specify fixed mode (since the override mode will either be the same as the fixed mode, or we'll be unable to check the bounds of the overried) - panel must specify at least one display_timing range which will be used to ensure the override mode fits within its bounds Changes in v2: - Parse the full display-timings node (using the native-mode) (Rob) Changes in v3: - No longer parse display-timings subnode, use panel-timing (Rob) Changes in v4: - Don't add mode from timing if override was specified (Thierry) - Add warning if timing and fixed mode was specified (Thierry) - Don't add fixed mode if timing was specified (Thierry) - Refactor/rename a bit to avoid extra indentation from "if" tests - i should be unsigned (Thierry) - Add annoying WARN_ONs for some cases (Thierry) - Simplify 'No display_timing found' handling (Thierry) - Rename to panel_simple_parse_override_mode() (Thierry) Changes in v5: - Added Heiko's Tested-by Changes in v6: - Rebased to drm-misc next - Added tags Cc: Doug Anderson <dianders@chromium.org> Cc: Eric Anholt <eric@anholt.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Stéphane Marchesin <marcheu@chromium.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: devicetree@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190711203455.125667-2-dianders@chromium.org
2019-07-11 13:34:53 -07:00
drm/panel-edp: Split eDP panels out of panel-simple The panel-simple driver handles way too much. Let's start trying to get a handle on it by splitting out the eDP panels. This patch does this: 1. Start by copying simple-panel verbatim over to a new driver, simple-panel-edp. 2. Rename "panel_simple" to "panel_edp" in the new driver. 3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new driver. Remove those panels from the old driver. 4. Remove all recent "DP AUX bus" stuff from the old driver. The DP AUX bus is only possible on DP panels. 5. Remove all DSI / MIPI related functions from the new driver. 6. Remove bus_format / bus_flags from eDP driver. These things don't seem to make any sense for eDP panels so let's stop filling in made up stuff. In the end we end up with a bunch of duplicated code for now. Future patches will try to address _some_ of this duplicated code though some of it will be unavoidable. NOTE: This may not actually move all eDP panels over to the new driver since not all panels were properly marked with `DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward panels I could identify but even so there may be some missed. Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.7.I0a2f75bb822d17ce06f5b147734764eeb0c3e3df@changeid
2021-09-14 13:21:54 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel-edp: Split eDP panels out of panel-simple The panel-simple driver handles way too much. Let's start trying to get a handle on it by splitting out the eDP panels. This patch does this: 1. Start by copying simple-panel verbatim over to a new driver, simple-panel-edp. 2. Rename "panel_simple" to "panel_edp" in the new driver. 3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new driver. Remove those panels from the old driver. 4. Remove all recent "DP AUX bus" stuff from the old driver. The DP AUX bus is only possible on DP panels. 5. Remove all DSI / MIPI related functions from the new driver. 6. Remove bus_format / bus_flags from eDP driver. These things don't seem to make any sense for eDP panels so let's stop filling in made up stuff. In the end we end up with a bunch of duplicated code for now. Future patches will try to address _some_ of this duplicated code though some of it will be unavoidable. NOTE: This may not actually move all eDP panels over to the new driver since not all panels were properly marked with `DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward panels I could identify but even so there may be some missed. Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.7.I0a2f75bb822d17ce06f5b147734764eeb0c3e3df@changeid
2021-09-14 13:21:54 -07:00
drm/panel-edp: Split eDP panels out of panel-simple The panel-simple driver handles way too much. Let's start trying to get a handle on it by splitting out the eDP panels. This patch does this: 1. Start by copying simple-panel verbatim over to a new driver, simple-panel-edp. 2. Rename "panel_simple" to "panel_edp" in the new driver. 3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new driver. Remove those panels from the old driver. 4. Remove all recent "DP AUX bus" stuff from the old driver. The DP AUX bus is only possible on DP panels. 5. Remove all DSI / MIPI related functions from the new driver. 6. Remove bus_format / bus_flags from eDP driver. These things don't seem to make any sense for eDP panels so let's stop filling in made up stuff. In the end we end up with a bunch of duplicated code for now. Future patches will try to address _some_ of this duplicated code though some of it will be unavoidable. NOTE: This may not actually move all eDP panels over to the new driver since not all panels were properly marked with `DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward panels I could identify but even so there may be some missed. Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.7.I0a2f75bb822d17ce06f5b147734764eeb0c3e3df@changeid
2021-09-14 13:21:54 -07:00
drm/panel-simple: Add Vivax TPC-9150 panel v6 The model and make of the LCD panel of the Vivax TPC-9150 is unknown, hence the panel settings that were retrieved with a FEX dump are named after the device NOT the actual panel. The LCD in question is a 50 pin MISO TFT LCD panel of the resolution 1024x600 used by the aforementioned device. Version 2, as Thierry kindly suggested that I fix the order in which the panel was ordered compared to others. Version 3, filling in the required info suggested by Sam. Plus some factual issues that I've corrected myself (tested working) Version 4, rearranged the display parameters and fix invalid bit format issue. (Thanks Sam) Version 5, referred to FEX file instead of manual debugging for information. Version 6, same as above. This time, it'll be documented. A bit of context first: I experimented with this a long time ago whilst I was first learning how to get Linux running on Allwinner boards, I didn't have many resources at hand so this was quite slow. Anyways, I stumbled upon this guide (https://linux-sunxi.org/LCD) and was reading about how to setup the LCD for my tablet. Since I was able to make a proper FEX dump, I was also able to read the correct parameters for myself without relying on leaked documents or part numbers and whatnot. In the FEX dump the value lcd_frm IS SET to 1, which means, at least according to the document, that this display is INDEED an 18 bit per pixel panel. Compiling U-Boot and seeing the tux in proper colors confirmed this. As per Sam Ravnborg's suggestion, I've changed the panel to his format "MEDIA_BUS_FMT_RGB666_1X7X3_SPWG", however this does not lead to any actual change in regards to the functionality since the sunxi panel driver just ignores this value. However, hopefully this clears up any errors down the road as either the driver becomes advanced enough to not ignore this value or that some other piece of software relies on this value being known. PS: Apologies to the maintainers that have to endure my misjudgement about how these things work. As for the concerns about a single patch series, I wasn't sure where to send the patches as they clearly aren't dt-bindings related and my previous patches have ended up in drm-misc-fixes anyway. So I'm guessing I'll be fine if I just post them in the list from last time??? Signed-off-by: Nikola Pavlica <pavlica.nikola@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211011212731.77763-1-pavlica.nikola@gmail.com
2021-10-11 23:27:31 +02:00
drm/panel-simple: Add Vivax TPC-9150 panel v6 The model and make of the LCD panel of the Vivax TPC-9150 is unknown, hence the panel settings that were retrieved with a FEX dump are named after the device NOT the actual panel. The LCD in question is a 50 pin MISO TFT LCD panel of the resolution 1024x600 used by the aforementioned device. Version 2, as Thierry kindly suggested that I fix the order in which the panel was ordered compared to others. Version 3, filling in the required info suggested by Sam. Plus some factual issues that I've corrected myself (tested working) Version 4, rearranged the display parameters and fix invalid bit format issue. (Thanks Sam) Version 5, referred to FEX file instead of manual debugging for information. Version 6, same as above. This time, it'll be documented. A bit of context first: I experimented with this a long time ago whilst I was first learning how to get Linux running on Allwinner boards, I didn't have many resources at hand so this was quite slow. Anyways, I stumbled upon this guide (https://linux-sunxi.org/LCD) and was reading about how to setup the LCD for my tablet. Since I was able to make a proper FEX dump, I was also able to read the correct parameters for myself without relying on leaked documents or part numbers and whatnot. In the FEX dump the value lcd_frm IS SET to 1, which means, at least according to the document, that this display is INDEED an 18 bit per pixel panel. Compiling U-Boot and seeing the tux in proper colors confirmed this. As per Sam Ravnborg's suggestion, I've changed the panel to his format "MEDIA_BUS_FMT_RGB666_1X7X3_SPWG", however this does not lead to any actual change in regards to the functionality since the sunxi panel driver just ignores this value. However, hopefully this clears up any errors down the road as either the driver becomes advanced enough to not ignore this value or that some other piece of software relies on this value being known. PS: Apologies to the maintainers that have to endure my misjudgement about how these things work. As for the concerns about a single patch series, I wasn't sure where to send the patches as they clearly aren't dt-bindings related and my previous patches have ended up in drm-misc-fixes anyway. So I'm guessing I'll be fine if I just post them in the list from last time??? Signed-off-by: Nikola Pavlica <pavlica.nikola@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211011212731.77763-1-pavlica.nikola@gmail.com
2021-10-11 23:27:31 +02:00
drm/panel: simple: add panel-dpi support The panel-dpi compatible is a fallback that allows the DT to specify the timing. When matching panel-dpi expect the device tree to include the timing information for the display-panel. Background for this change: There are a lot of panels and new models hits the market very often. It is a lost cause trying to chase them all and users of new panels will often find them in situations that the panel they ues are not supported by the kernel. On top of this a lot of panels are customized based on customer specifications. Including the panel timing in the device tree allows for a simple way to describe the actual HW and use this description in a generic way in the kernel. This allows uses of proprietary panels, or panels which are not included in the kernel, to specify the timing in the device tree together with all the other HW descriptions. And thus, using the device tree it is then easy to add support for an otherwise unknown panel. The current support expect panels that do not require any delays for prepare/enable/disable/unprepare. Oleksandr Suvorov replied: I've just tested this patch on Apalis iMX6Q and Colibri iMX7D using panel settings from the following patch: https://lore.kernel.org/linux-arm-kernel/20200115123401.2264293-4-oleksandr.suvorov@toradex.com/ It works for me, thanks! Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Tested-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Maxime Ripard <mripard@kernel.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200216181513.28109-6-sam@ravnborg.org
2020-02-16 19:15:13 +01:00
drm/panel-edp: Split eDP panels out of panel-simple The panel-simple driver handles way too much. Let's start trying to get a handle on it by splitting out the eDP panels. This patch does this: 1. Start by copying simple-panel verbatim over to a new driver, simple-panel-edp. 2. Rename "panel_simple" to "panel_edp" in the new driver. 3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new driver. Remove those panels from the old driver. 4. Remove all recent "DP AUX bus" stuff from the old driver. The DP AUX bus is only possible on DP panels. 5. Remove all DSI / MIPI related functions from the new driver. 6. Remove bus_format / bus_flags from eDP driver. These things don't seem to make any sense for eDP panels so let's stop filling in made up stuff. In the end we end up with a bunch of duplicated code for now. Future patches will try to address _some_ of this duplicated code though some of it will be unavoidable. NOTE: This may not actually move all eDP panels over to the new driver since not all panels were properly marked with `DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward panels I could identify but even so there may be some missed. Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.7.I0a2f75bb822d17ce06f5b147734764eeb0c3e3df@changeid
2021-09-14 13:21:54 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel-edp: Split eDP panels out of panel-simple The panel-simple driver handles way too much. Let's start trying to get a handle on it by splitting out the eDP panels. This patch does this: 1. Start by copying simple-panel verbatim over to a new driver, simple-panel-edp. 2. Rename "panel_simple" to "panel_edp" in the new driver. 3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new driver. Remove those panels from the old driver. 4. Remove all recent "DP AUX bus" stuff from the old driver. The DP AUX bus is only possible on DP panels. 5. Remove all DSI / MIPI related functions from the new driver. 6. Remove bus_format / bus_flags from eDP driver. These things don't seem to make any sense for eDP panels so let's stop filling in made up stuff. In the end we end up with a bunch of duplicated code for now. Future patches will try to address _some_ of this duplicated code though some of it will be unavoidable. NOTE: This may not actually move all eDP panels over to the new driver since not all panels were properly marked with `DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward panels I could identify but even so there may be some missed. Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.7.I0a2f75bb822d17ce06f5b147734764eeb0c3e3df@changeid
2021-09-14 13:21:54 -07:00
drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare Unpreparing and re-preparing a panel can be a really heavy operation. Panels datasheets often specify something on the order of 500ms as the delay you should insert after turning off the panel before turning it on again. In addition, turning on a panel can have delays on the order of 100ms - 200ms before the panel will assert HPD (AKA "panel ready"). The above means that we should avoid turning a panel off if we're going to turn it on again shortly. The above becomes a problem when we want to read the EDID of a panel. The way that ordering works is that userspace wants to read the EDID of the panel _before_ fully enabling it so that it can set the initial mode correctly. However, we can't read the EDID until we power it up. This leads to code that does this dance (like ps8640_bridge_get_edid()): 1. When userspace requests EDID / the panel modes (through an ioctl), we power on the panel just enough to read the EDID and then power it off. 2. Userspace then turns the panel on. There's likely not much time between step #1 and #2 and so we want to avoid powering the panel off and on again between those two steps. Let's use Runtime PM to help us. We'll move the existing prepare() and unprepare() to be runtime resume() and runtime suspend(). Now when we want to prepare() or unprepare() we just increment or decrement the refcount. We'll default to a 1 second autosuspend delay which seems sane given the typical delays we see for panels. A few notes: - It seems the existing unprepare() and prepare() are defined to be no-ops if called extra times. We'll preserve that behavior but may try to remove it in a future patch. - This is a slight change in the ABI of simple panel. If something was absolutely relying on the unprepare() to happen instantly that simply won't be the case anymore. I'm not aware of anyone relying on that behavior, but if there is someone then we'll need to figure out how to enable (or disable) this new delayed behavior selectively. - In order for this to work we now have a hard dependency on "PM". From memory this is a legit thing to assume these days and we don't have to find some fallback to keep working if someone wants to build their system without "PM". Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210416153909.v4.7.I9e8bd33b49c496745bfac58ea9ab418bd3b6f5ce@changeid
2021-04-16 15:39:30 -07:00
drm/panel-edp: Split eDP panels out of panel-simple The panel-simple driver handles way too much. Let's start trying to get a handle on it by splitting out the eDP panels. This patch does this: 1. Start by copying simple-panel verbatim over to a new driver, simple-panel-edp. 2. Rename "panel_simple" to "panel_edp" in the new driver. 3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new driver. Remove those panels from the old driver. 4. Remove all recent "DP AUX bus" stuff from the old driver. The DP AUX bus is only possible on DP panels. 5. Remove all DSI / MIPI related functions from the new driver. 6. Remove bus_format / bus_flags from eDP driver. These things don't seem to make any sense for eDP panels so let's stop filling in made up stuff. In the end we end up with a bunch of duplicated code for now. Future patches will try to address _some_ of this duplicated code though some of it will be unavoidable. NOTE: This may not actually move all eDP panels over to the new driver since not all panels were properly marked with `DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward panels I could identify but even so there may be some missed. Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.7.I0a2f75bb822d17ce06f5b147734764eeb0c3e3df@changeid
2021-09-14 13:21:54 -07:00