linux/drivers/hwmon/Kconfig

2741 lines
83 KiB

hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 17:28:05 +03:00
hwmon: Add Baikal-T1 PVT sensor driver Baikal-T1 SoC provides an embedded process, voltage and temperature sensor to monitor an internal SoC environment (chip temperature, supply voltage and process monitor) and on time detect critical situations, which may cause the system instability and even damages. The IP-block is based on the Analog Bits PVT sensor, but is equipped with a dedicated control wrapper, which provides a MMIO registers-based access to the sensor core functionality (APB3-bus based) and exposes an additional functions like thresholds/data ready interrupts, its status and masks, measurements timeout. All of these is used to create a hwmon driver being added to the kernel by this commit. The driver implements support for the hardware monitoring capabilities of Baikal-T1 process, voltage and temperature sensors. PVT IP-core consists of one temperature and four voltage sensors, each of which is implemented as a dedicated hwmon channel config. The driver can optionally provide the hwmon alarms for each sensor the PVT controller supports. The alarms functionality is made compile-time configurable due to the hardware interface implementation peculiarity, which is connected with an ability to convert data from only one sensor at a time. Additional limitation is that the controller performs the thresholds checking synchronously with the data conversion procedure. Due to these limitations in order to have the hwmon alarms automatically detected the driver code must switch from one sensor to another, read converted data and manually check the threshold status bits. Depending on the measurements timeout settings this design may cause additional burden on the system performance. By default if the alarms kernel config is disabled the data conversion is performed by the driver on demand when read operation is requested via corresponding _input-file. Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 17:28:05 +03:00
hwmon: Add support for Amphenol ChipCap 2 The Amphenol ChipCap 2 is a capacitive polymer humidity and temperature sensor with an integrated EEPROM and minimum/maximum humidity alarms. All device variants offer an I2C interface and depending on the part number, two different output modes: - CC2D: digital output - CC2A: analog (PDM) output This driver adds support for the digital variant (CC2D part numbers), which includes the following part numbers: - non-sleep measurement mode (CC2D23, CC2D25, CC2D33, CC2D35) - sleep measurement mode (CC2D23S, CC2D25S, CC2D33S, CC2D35S) The Chipcap 2 EEPROM can be accessed to configure a series of parameters like the minimum/maximum humidity alarm threshold and hysteresis. The EEPROM is only accessible in the command window after a power-on reset. The default window lasts 10 ms if no Start_CM command is sent. After the command window is finished (either after the mentioned timeout of after a Start_NOM command is sent), the device enters the normal operation mode and makes a first measurement automatically. Unfortunately, the device does not provide any hardware or software reset and therefore the driver must trigger power cycles to enter the command mode. A dedicated, external regulator is required for that. This driver keeps the device off until a measurement or access to the EEPROM is required, making use of the first automatic measurement to avoid different code paths for sleep and non-sleep devices. The minimum and maximum humidity alarms are configured with two registers per alarm: one stores the alarm threshold and the other one keeps the value that turns off the alarm. The alarm signals are only updated when a measurement is carried out. Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://lore.kernel.org/r/20240130-topic-chipcap2-v6-5-260bea05cf9b@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2024-01-30 22:06:48 +01:00
hwmon: Driver for disk and solid state drives with temperature sensors Reading the temperature of ATA drives has been supported for years by userspace tools such as smarttools or hddtemp. The downside of such tools is that they need to run with super-user privilege, that the temperatures are not reported by standard tools such as 'sensors' or 'libsensors', and that drive temperatures are not available for use in the kernel's thermal subsystem. This driver solves this problem by adding support for reading the temperature of ATA drives from the kernel using the hwmon API and by adding a temperature zone for each drive. With this driver, the hard disk temperature can be read using the unprivileged 'sensors' application: $ sensors drivetemp-scsi-1-0 drivetemp-scsi-1-0 Adapter: SCSI adapter temp1: +23.0°C or directly from sysfs: $ grep . /sys/class/hwmon/hwmon9/{name,temp1_input} /sys/class/hwmon/hwmon9/name:drivetemp /sys/class/hwmon/hwmon9/temp1_input:23000 If the drive supports SCT transport and reports temperature limits, those are reported as well. drivetemp-scsi-0-0 Adapter: SCSI adapter temp1: +27.0°C (low = +0.0°C, high = +60.0°C) (crit low = -41.0°C, crit = +85.0°C) (lowest = +23.0°C, highest = +34.0°C) The driver attempts to use SCT Command Transport to read the drive temperature. If the SCT Command Transport feature set is not available, or if it does not report the drive temperature, drive temperatures may be readable through SMART attributes. Since SMART attributes are not well defined, this method is only used as fallback mechanism. Cc: Chris Healy <cphealy@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-28 21:34:40 -08:00
hwmon: Driver for disk and solid state drives with temperature sensors Reading the temperature of ATA drives has been supported for years by userspace tools such as smarttools or hddtemp. The downside of such tools is that they need to run with super-user privilege, that the temperatures are not reported by standard tools such as 'sensors' or 'libsensors', and that drive temperatures are not available for use in the kernel's thermal subsystem. This driver solves this problem by adding support for reading the temperature of ATA drives from the kernel using the hwmon API and by adding a temperature zone for each drive. With this driver, the hard disk temperature can be read using the unprivileged 'sensors' application: $ sensors drivetemp-scsi-1-0 drivetemp-scsi-1-0 Adapter: SCSI adapter temp1: +23.0°C or directly from sysfs: $ grep . /sys/class/hwmon/hwmon9/{name,temp1_input} /sys/class/hwmon/hwmon9/name:drivetemp /sys/class/hwmon/hwmon9/temp1_input:23000 If the drive supports SCT transport and reports temperature limits, those are reported as well. drivetemp-scsi-0-0 Adapter: SCSI adapter temp1: +27.0°C (low = +0.0°C, high = +60.0°C) (crit low = -41.0°C, crit = +85.0°C) (lowest = +23.0°C, highest = +34.0°C) The driver attempts to use SCT Command Transport to read the drive temperature. If the SCT Command Transport feature set is not available, or if it does not report the drive temperature, drive temperatures may be readable through SMART attributes. Since SMART attributes are not well defined, this method is only used as fallback mechanism. Cc: Chris Healy <cphealy@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-28 21:34:40 -08:00
x86/Kconfig: move and modify CONFIG_I8K In Kconfig, inside the "Processor type and features" menu, there is the CONFIG_I8K option: "Dell i8k legacy laptop support". This is very confusing - enabling CONFIG_I8K is not required for the kernel to support old Dell laptops. This option is specific to the dell-smm-hwmon driver, which mostly exports some hardware monitoring information and allows the user to change fan speed. This option is misplaced, so move CONFIG_I8K to drivers/hwmon/Kconfig, where it belongs. Also, modify the dependency order - change select SENSORS_DELL_SMM to depends on SENSORS_DELL_SMM as it is just a configuration option of dell-smm-hwmon. This includes changing the option type from tristate to bool. It was tristate because it could select CONFIG_SENSORS_DELL_SMM=m . When running "make oldconfig" on configurations with CONFIG_SENSORS_DELL_SMM enabled , this change will result in an additional question (which could be printed several times during bisecting). I think that tidying up the configuration is worth it, though. Next patch tweaks the description of CONFIG_I8K. Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl> Cc: Pali Rohár <pali@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Mark Gross <markgross@kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Borislav Petkov <bp@suse.de> Link: https://lore.kernel.org/r/20220212125654.357408-1-mat.jonczyk@o2.pl Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-02-12 13:56:53 +01:00
x86/Kconfig: move and modify CONFIG_I8K In Kconfig, inside the "Processor type and features" menu, there is the CONFIG_I8K option: "Dell i8k legacy laptop support". This is very confusing - enabling CONFIG_I8K is not required for the kernel to support old Dell laptops. This option is specific to the dell-smm-hwmon driver, which mostly exports some hardware monitoring information and allows the user to change fan speed. This option is misplaced, so move CONFIG_I8K to drivers/hwmon/Kconfig, where it belongs. Also, modify the dependency order - change select SENSORS_DELL_SMM to depends on SENSORS_DELL_SMM as it is just a configuration option of dell-smm-hwmon. This includes changing the option type from tristate to bool. It was tristate because it could select CONFIG_SENSORS_DELL_SMM=m . When running "make oldconfig" on configurations with CONFIG_SENSORS_DELL_SMM enabled , this change will result in an additional question (which could be printed several times during bisecting). I think that tidying up the configuration is worth it, though. Next patch tweaks the description of CONFIG_I8K. Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl> Cc: Pali Rohár <pali@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Mark Gross <markgross@kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Borislav Petkov <bp@suse.de> Link: https://lore.kernel.org/r/20220212125654.357408-1-mat.jonczyk@o2.pl Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-02-12 13:56:53 +01:00
x86/Kconfig: move and modify CONFIG_I8K In Kconfig, inside the "Processor type and features" menu, there is the CONFIG_I8K option: "Dell i8k legacy laptop support". This is very confusing - enabling CONFIG_I8K is not required for the kernel to support old Dell laptops. This option is specific to the dell-smm-hwmon driver, which mostly exports some hardware monitoring information and allows the user to change fan speed. This option is misplaced, so move CONFIG_I8K to drivers/hwmon/Kconfig, where it belongs. Also, modify the dependency order - change select SENSORS_DELL_SMM to depends on SENSORS_DELL_SMM as it is just a configuration option of dell-smm-hwmon. This includes changing the option type from tristate to bool. It was tristate because it could select CONFIG_SENSORS_DELL_SMM=m . When running "make oldconfig" on configurations with CONFIG_SENSORS_DELL_SMM enabled , this change will result in an additional question (which could be printed several times during bisecting). I think that tidying up the configuration is worth it, though. Next patch tweaks the description of CONFIG_I8K. Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl> Cc: Pali Rohár <pali@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Mark Gross <markgross@kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Borislav Petkov <bp@suse.de> Link: https://lore.kernel.org/r/20220212125654.357408-1-mat.jonczyk@o2.pl Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-02-12 13:56:53 +01:00
x86/Kconfig: move and modify CONFIG_I8K In Kconfig, inside the "Processor type and features" menu, there is the CONFIG_I8K option: "Dell i8k legacy laptop support". This is very confusing - enabling CONFIG_I8K is not required for the kernel to support old Dell laptops. This option is specific to the dell-smm-hwmon driver, which mostly exports some hardware monitoring information and allows the user to change fan speed. This option is misplaced, so move CONFIG_I8K to drivers/hwmon/Kconfig, where it belongs. Also, modify the dependency order - change select SENSORS_DELL_SMM to depends on SENSORS_DELL_SMM as it is just a configuration option of dell-smm-hwmon. This includes changing the option type from tristate to bool. It was tristate because it could select CONFIG_SENSORS_DELL_SMM=m . When running "make oldconfig" on configurations with CONFIG_SENSORS_DELL_SMM enabled , this change will result in an additional question (which could be printed several times during bisecting). I think that tidying up the configuration is worth it, though. Next patch tweaks the description of CONFIG_I8K. Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl> Cc: Pali Rohár <pali@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Mark Gross <markgross@kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Borislav Petkov <bp@suse.de> Link: https://lore.kernel.org/r/20220212125654.357408-1-mat.jonczyk@o2.pl Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-02-12 13:56:53 +01:00
hwmon: (powerpc/powernv) hwmon driver for power, fan rpm, voltage and temperature This patch adds basic kernel support for reading power values, fan speed rpm, voltage and temperature data on powernv platforms which will be exported to user space through sysfs interface. Test results: ------------- [root@tul163p1 ~]# sensors ibmpowernv-isa-0000 Adapter: ISA adapter fan1: 5465 RPM (min = 0 RPM) fan2: 5152 RPM (min = 0 RPM) fan3: 5521 RPM (min = 0 RPM) fan4: 4891 RPM (min = 0 RPM) fan5: 0 RPM (min = 0 RPM) fan6: 0 RPM (min = 0 RPM) fan7: 7480 RPM (min = 0 RPM) fan8: 7944 RPM (min = 0 RPM) temp1: +39.0°C (high = +0.0°C) power1: 190.00 W [root@tul163p1 ~]# ls /sys/devices/platform/ alarmtimer ibmpowernv.0 power rtc-generic serial8250 uevent [root@tul163p1 ~]# ls /sys/devices/platform/ibmpowernv.0/hwmon/hwmon0/ device fan2_min fan4_min fan6_min fan8_min power fan1_fault fan3_fault fan5_fault fan7_fault in1_fault power1_input fan1_input fan3_input fan5_input fan7_input in2_fault subsystem fan1_min fan3_min fan5_min fan7_min in3_fault temp1_input fan2_fault fan4_fault fan6_fault fan8_fault in4_fault temp1_max fan2_input fan4_input fan6_input fan8_input name uevent [root@tul163p1 ~]# ls /sys/class/hwmon/hwmon0/ device fan2_min fan4_min fan6_min fan8_min power fan1_fault fan3_fault fan5_fault fan7_fault in1_fault power1_input fan1_input fan3_input fan5_input fan7_input in2_fault subsystem fan1_min fan3_min fan5_min fan7_min in3_fault temp1_input fan2_fault fan4_fault fan6_fault fan8_fault in4_fault temp1_max fan2_input fan4_input fan6_input fan8_input name uevent [root@tul163p1 ~]# Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-07-08 14:38:38 +05:30
2022-05-09 16:47:40 -07:00
hwmon: Add driver for NZXT Kraken X and Z series AIO CPU coolers This driver enables hardware monitoring support for NZXT Kraken X53/X63/X73 and Z53/Z63/Z73 all-in-one CPU liquid coolers. All models expose liquid temperature and pump speed (in RPM), as well as PWM control (natively only through a temp-PWM curve, but the driver also emulates fixed PWM control on top of that). The Z-series models additionally expose the speed and duty of an optionally connected fan, with the same PWM control capabilities. Pump and fan duty control mode can be set through pwm[1-2]_enable, where 1 is for the manual control mode and 2 is for the liquid temp to PWM curve mode. Writing a 0 disables control of the channel through the driver after setting its duty to 100%. As it is not possible to query the device for the active mode, the driver keeps track of it. The temperature of the curves relates to the fixed [20-59] C range, per device limitations, and correlating to the detected liquid temperature. Only PWM values (ranging from 0-255) can be set. The addressable RGB LEDs and LCD screen, included only on Z-series models, are not supported in this driver. Co-developed-by: Jonas Malaco <jonas@protocubo.io> Signed-off-by: Jonas Malaco <jonas@protocubo.io> Co-developed-by: Yury Zhuravlev <stalkerg@gmail.com> Signed-off-by: Yury Zhuravlev <stalkerg@gmail.com> Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20240129111932.368232-1-savicaleksa83@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2024-01-29 12:19:28 +01:00
hwmon: add HP WMI Sensors driver Hewlett-Packard (and some HP Compaq) business-class computers report hardware monitoring information via WMI. This driver exposes that information to hwmon. Initial support is provided for temperature, fan speed, and intrusion sensor types. Provisional support is provided for voltage and current sensor types. HP's WMI implementation permits many other types of numeric sensors. Therefore, a debugfs interface is also provided to enumerate and inspect all numeric sensors visible on the WMI side. This should facilitate adding support for other sensor types in the future. Tested on a HP Z420, a HP EliteOne 800 G1, and a HP Compaq Elite 8300 SFF. Note that provisionally supported sensor types are untested and seem to be rare-to-nonexistent in the wild, having been encountered neither on test systems nor in ACPI dumps from the Linux Hardware Database. They are included because their popularity in general makes their presence on past or future HP systems plausible and because no doubt exists as to how the sensors themselves would be represented in WMI (alarm attributes will need to wait for hardware to be located). A 2005 HP whitepaper gives the relevant sensor object MOF definition and sensor value scaling calculation, and both this driver and the official HP Performance Advisor utility comply with them (confirmed in the latter case by reverse engineering). Link: https://h20331.www2.hp.com/hpsub/downloads/cmi_whitepaper.pdf Signed-off-by: James Seo <james@equiv.tech> Link: https://lore.kernel.org/r/20230522115645.509701-1-james@equiv.tech [groeck: Set error return value for intrusion writes to -EINVAL. Always accept writes of 0 even if there was no intrusion. ] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2023-05-22 04:56:46 -07:00